CONTENTS

Safety Instructions 2
䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉

1. L-0185 Slit Lamp 3

䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉

2. L-0187 Slit Lamp 䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉

4
3. L-0189 Slit Lamp 䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉
5
4. L-0240 Slit Lamp 䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉
6
5. Unpacking and Assembling 䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉
7
6. Operation 10
䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉

7. Maintenance 14
䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉

8. Electrical Wiring Diagrams 15

䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉䞉

Notice
1)In order to keep the instrumentinthe best condition, please readthis manual and performthe
inspectionsof the instrument.
2) Please store the instrument avoiding humidity.
3)Beforeyou move this instrument, pleaseholdthe armand tightenthe handle to lockthe first
arm.
The instrument with locked arm should be movedslowly.
4) The content of this manual maybe changed without prior notice according to the update of
the product specification.
5) This manual is created completely. Please contact your dealer in the unlikely event that you
find any
errors in writing or missing stated points.
6) The manual will be replaced with new one if it hasmanufacturing defects. Please contact your
dealer.

Indication
Name plate
The following matters are displayed on a nameplate.
䞉Product name 䞉Model No. 䞉Maunfacture & Distributer 䞉Serial No.

The following emblems are displayed.

-1-
Safety Instructions
Please read this operation manual carefully before using the instrument.
This manual should be kept in a place where it is available for the operator whenever they need.
You must follow the safety instructions below that describes the important precautions.
The symbols and their meanings are as follows.

indicates that death or serious physical injuries will occur if necessary

Danger safety precautions are not taken.
indicates that death or serious physical injuries can occur if necessary
Warning safety precautions are not taken.
indicates that a slight physical injury or material damage can occur if
Caution necessary safety precautions are not taken.
Material damage means expanded damages related to houses, household goods, etc.

Warning
䞉During the replacement of parts, make sure to set main power switch OFF (O).
If you operate while energizing, it will cause electric shock.
䞉Do not tilt the body of the main unit more than 10 degrees.
Physical injury or material damage of houses and other instruments can occur if the unit falls over.

Caution
not use
䞉Donot
䞉Do use other
otherthan
thanAC AC100V.220V.
The equipment cannot be used except for the specified power supply voltage.
The equipment cannot be used except for the specified power supply voltage.
Using wrong power supply voltage may cause ignition.
Using wrong power supply voltage may cause ignition.
䞉Make sure to install the ground wire.
sure to
䞉MakeElectric install the ground wire.
shock may be caused when mechanical failure or electric leakage occurs.
Electric shock may be caused when mechanical failure or electric leakage occurs.
䞉Whenunplugging
䞉When /plugging
unplugging /plugging in theinpower
the power supply
supply plug, hands plug,
musthands
be dry tomust be dry to unplugging /
unplugging
plugging in /plugging
the outletin the outlet
with with insertion
insertion plug.plug.
Electric shock or ignition caused by short-circuit may occur.
Electric shock or ignition caused by short-circuit may occur.
䞉Do not use the
䞉Do not use the power power supply
supply cordplugs
cord and andwhenplugs when
they they are deteriorated
are deteriorated or damaged. or damaged.
Electric shockor or
Electric shock ignition
ignition causedcaused by short-circuit
by short-circuit may occur.may occur.
䞉Do not take following actions: damaging, bending with force, pulling, twisting and bundling
䞉Do not take following actions: damaging, bending with force, pulling, twisting and bundling the
the power supply cord as well as putting heavy things on it and pressing it.
power supply cord as well as putting heavy things on it and pressing it.
The
The power
power cordcordmaymay be damaged
be damaged resultingresulting in fire shock.
in fire or electric or electric shock.
䞉Keep the power cord clean at all times so that there is no dirt, oil etc.
If the
䞉Keep terminal
the power cordpart
cleanisatdirty, it may
all times cause
so that there ismechanical breakdown or fire.
no dirt, oil etc.
䞉Except If the
forterminal
medical parttreatment
is dirty, it may causeplease
hours, mechanical breakdown
unplug the plugor fire.
from the outlet.
It may cause electric leakage or fire.
䞉Except for medical treatment hours, please unplug the plug from the outlet.
䞉Do not usecause
It may bulbs, fuses,
electric electric
leakage parts other than specified.
or fire.
There is risk of fire caused by heating.
䞉Do not use bulbs, fuses, electric parts other than specified.
䞉Handle lenses and mirrors carefully.
There is risk of fire caused by heating.
When lenses and mirrors are scratched, it will not be possible to observe properly.
䞉Do not use
䞉Handle lenseslenses othercarefully.
and mirrors than specified.
When lenses
When wrongand mirrors
lens are are
used,scratched, it willbe
it will not notpossible
be possible totoobserve
observe properly.
with the proper focus and
䞉Domagnification.
not use lenses other than specified.
䞉When Whensetting
wrongthelensmain unit itwith
are used, thebetable,
will not possible fixtothem firmly
observe with with the handle
the proper of the table
focus and
magnification.
clamping system.
䞉When setting the main unit with the table, fix them firmly with the handle of the table clamping
If the unit slides sideways on the table and falls over, physical injury or material damage of
system.
houses
If the unitand
slidesother instruments
sideways can
on the table and occur.
falls over, physical injury or material damage of
houses
䞉Please anddisassemble
never other instruments can
the occur.
unit body.
䞉Please never disassemble the unit body.
Disassembling
Disassembling thethe
unitunit
bodybody will cause
will cause mechanical
mechanical breakdownbreakdown
or fire. or fire.

-2-
 1. L-0185 SLIT LAMP
New L-0185 & L0185DC, top line 911 series of INAMI Slit Lamp microscope, are now available with
advanced features. L-0185 & L0185DC are designed based on experience of INAMI for over 90 years
in designing, qualifying and manufacturing high quality ophthalmic instruments.

䐟 Lamp Housing Cover

䐱 Lamp Housing Cover
䐠 Slit Length Scale
Retaining Nuts
䐡 Filter Control Lever
䐢 Slit Rotation Control Lever and 䐲 Headrest
䞡 Focusing Rod
Slit Length Control Knob
䐣 Prism Housings 䞢 Angle Scale Ring
䐤 Eyepiece Focus Adjustment Ring 䞣 Angle Index Ring
䐥 Eyeiece 䞤 Illumination Arm Lock
䐦 Lever for converting magnification 䞥 Microscope Arm Lock
䐧 Centering Screw 䞦 Horizontal Motion
䐨 Slit Tilt Stops Lock䞧 Rack Cover
䐩 Slit Tilt Latch 䞨 Control for Chinrest
䐪 Slit Width Control Knob
䐪-A Slit Width Control Scale
䐫 Microscope Arm
䐬 Joystick (Horizontal & Vertical
direction control) -A
䐭 Illumination Control Knob
䐮 Pilot Lamp
䐯 Power Switch
䐰 Joystick Glide Plate

Fig. 1

Specification : L-0185
Converging binocular microscope
Eyepiece Eyepiece magnification: 10x, 16x䚷 䚷Objectives magnification: 1x, 1.6x
Total magnification: 10x, 16x, 25x
P.D.adjustment 52-90mm (w/10x eyepieces)
Illumination unit
Slit Slit image rotation angle: 0 - 180°, 䚷 Tilting illumination: 5, 10, 15, 20°
Slit diaphragm disc: 10 / 6 / 4 / 3 / 2 / 1 / 0.2mm
Wedge-shaped diaphragm for variable slit lengths
Filter Unfiltered (Opened aperture), Cobalt blue, ND(T:50%), Heat absorbing, Red free filter
Controller Joystick (Horizontal & Vertical direction, coaxial control)
Light source 12V/50W Halogen bulb (L0160H1)䚷䚷*prefocused
Optional accessories
Applanation tonometer, Fixation lamp
-3-
 2. L-0187 SLIT LAMP
INAMI L-0187 Slit Lamp microscope provides all the features required to perform a complete slit
lamp examination for eye care professionals. L-0187 is designed based on experience of INAMI for
over 90 years in designing, qualifying and manufacturing high quality ophthalmic instruments.

䐟 Lamp Housing Cover 䐱 Lamp Housing Cover

䐠 Slit Length Scale
Retaining Nuts
䐡 Filter Control Lever
䐢 Slit Rotation Control Lever and 䐲 Headrest
Slit Length Control Knob 䞡 Focusing Rod
䐣 Prism Housings 䞢 Angle Scale Ring
䐤 Eyepiece Focus Ring 䞣 Angle Index Ring
䐥 Eyepiece 䞤 Illumination Arm Lock
䐦 Magnification Control Knob 䞥 Microscope Arm Lock
䐧 Centering Screw 䞦 Horizontal Motion Lock
䐨 Slit Tilt Stops 䞧 Rack Cover
䐩 Slit Tilt Latch 䞨 Control for Chinrest
䐪 Slit Width Control Knob
䐪-A Slit Width Control Scale
䐫 Microscope Arm
䐬 Joystick (Horizontal & Vertical
direction control)
䐭 Illumination Control Knob
䐮 Pilot Lamp
䐯 Power Switch
䐰 Joystick Glide Plate -A
㻙㻭

Fig.2

Specifications : L-0187
Parallel tube stereomicroscope
Eyepiece Eyepiece magnification: 12.5x, Variable magnification: 10x, 16x, 25x
Working distance: 98mm, Diopter adjustment range: - 6D to + 6D
P.D.adjustment 53-83mm
Illumination system
Slit Slit length: 0.2, 1, 3, 4, 6, 10mm in steps / 0-10mm continuously variable
Slit width: 0-10mm continuously variable
Slit image rotation angle: 0 - 180°, Slit tilt: 5, 10, 15, 20°
Filter Unfiltered (Opened aperture), Cobalt blue, ND(T:50%), Heat absorbing, Red-free filter
Light source 12V / 50W Halogen bulb (L0160H1) *prefocused
Optional accessories:
Applanation tonometer, Beam splitter module, Obserbation tube for image rotation,
35mm camera adaptor,35mm SLR camera body with automatic film advance,CCD TV Camera & adaptor
-4-
 3. L-0189 SLIT LAMP
INAMI L-0189 Slit Lamp microscope provides all the features required to perform a complete slit
lamp examination for eye care professionals. L-0189 is designed based on experience of INAMI for
over 90 years in designing, qualifying and manufacturing high quality ophthalmic instruments.

䐟 Lamp Housing Cover 䐱 Lamp Housing Cover

䐠 Slit Length Scale Retaining Nuts
䐡 Filter Control Lever 䐲 Headrest
䐢 Slit Rotation Control Lever and
䞡 Focusing Rod
Slit Length Control Knob 䞢 Angle Scale Ring
䐣 Prism Housings
䞣 Angle Index Ring
䐤 Eyepiece Focus Ring
䞤 Illumination Arm Lock
䐥 Eyepiece 䞥 Microscope Arm Lock
䐦 Magnification Control Knob 䞦 Horizontal Motion Lock
䐧 Centering Screw 䞧 Rack Cover
䐨 Slit Tilt Stops 䞨 Control for Chinrest
䐩 Slit Tilt Latch
䐪 Slit Width Control Knob
䐪-A Slit Width Control Scale
䐫 Microscope Arm
䐬 Joystick (Horizontal & Vertical
direction control)
䐭 Illumination Control Knob
䐮 Pilot Light
䐯 Power Switch
䐰 Joystick Glide Plate -A

Fig.3

Specifications: L-0189
Parallel tube stereomicroscope
Magnification Eyepieces: Total Magnification: 12.5x,
Variable magnification: 6x, 10x, 16x, 25x, 40x
Working distance: 98mm, Diopter adjustment range: - 6D to + 6D
P.D.adjustment 53 - 83mm
Illumination system
Slit Slit length: 0.2, 1, 3, 4, 6, 10mm in steps / 0–10mm continuously variable
Slit width: 0-10mm continuously variable, Slit image rotation: 0–180°,
Slit tilt: 5, 10, 15, 20°
Filter Unfiltered (Opened aperture), Cobalt blue, ND(T:50%), Heat absorbing, Red-free filter
Light source 12V/50W Halogen bulb (L0160H1)䚷䚷䚷*prefocused
Optional accessories
Applanation tonometer, Beam splitter module, Obserbation tube for image rotation,
35mm camera adaptor,35mm SLR camera body with automatic film advance,CCD TV Camera & adaptor
-5-
 4. L-0240 SLIT LAMP
INAMI L-0240 Slit Lamp microscope provides all the features required to perform a complete slit
lamp examination for eye care professionals. L-0240 is designed based on experience of INAMI for
over 90 years in designing, qualifying and manufacturing high quality ophthalmic instruments.

䐟 Lamp Housing Cover 䐱 Lamp Housing Cover

䐠 Slit Length Scale Retaining Nuts
䐡 Filter Control Lever 䐲 Headrest
䐢 Slit Rotation Control Lever and
䞡 Focusing Rod
Slit Length Control Knob
䞢 Angle Scale Ring
䐣 Prism Housings
䞣 Angle Index Ring
䐤 Eyepiece Focus Ring
䞤 Illumination Arm Lock
䐥 Eyepiece
䞥 Microscope Arm Lock
䐦 Magnification Control Knob
䐧 Centering Screw 䞦 Horizontal Motion Lock
䐨 Slit Tilt Stops 䞧 Rack Cover
䐩 Slit Tilt Latch 䞨 Control for Chinrest
䐪 Slit Width Control Knob
䐪-A, Slit Width Control Scale
䐫 Microscope Arm
䐬 Joystick (Horizontal &
Vertical direction control)
䐭 Illumination Control Knob
䐮 Pilot Lamp
䐯 Power Switch
䐰 Joystick Glide Plate
-A

Fig.4

Specifications : L-0240
Parallel tube stereomicroscope
Eyepieces Eyepieces: 15x, Variable magnification: 11x – 33x ,
Working distance: 98mm, Diopter adjustment range: - 6D to + 6D
P.D.adjustment 53 - 83mm
Illumination system
Slit Slit length: 0.2, 1, 3, 4, 6, 10mm in steps / 0 – 10mm continuously variable
Slit width: 0 – 10mm continuously variable
Slit image rotation angle: 0 - 180°, Slit tilt: 5, 10, 15, 20°
Filter Unfiltered (Opened aperture), Cobalt blue, ND(T:50%), Heat absorbing, Red-free filter
Light source 12V/50W Halogen bulb (L0160H1) *prefocused
Optional accessories:
Applanation tonometer, Beam splitter module, Obserbation tube for image rotation, 35mm camera adaptor
35mm SLR camera body with automatic film advance, CCD TV Camera & adaptor
-6-
5. Unpacking and Assembling
Unpacking Assembling
Headrest on tabletop
The whole package of INAMI Slit Lamp is consist 1) Take out the tabletop and accessaries from
of 3 stackable styrofoam hard containers. the upper container.
They are covered with a durable sheet(Fig. 5). 2) Place the tabletop upside down on a table or
Each box contains items as below. other suitable workbench.
The headrest side of the table top is made the
Lower container (Fig. 6) lamp
- Microscope with supporting arm unit side.
- Illumination unit with supporting arm 3) Unscrew 2 hex socket screws from Headrest
- Focusing rod mounting bracket using with one of the supplied
- 3 hexagonal wrenches for assembling wrenches (Fig. 9).
4) Unscrew the thumbscrews from the wire
Middle container (Fig. 7) retaining plastic plate (Fig. 10).
- Headrest 5) Assemble Headrest to Mounting plate.
- Fixation unit Make sure that the bottom of the plate engages
the groove of Headrest. The wires should be in
Upper container (Fig. 8) the the goove of the bracket (Fig. 11).
- Tabletop (Option) 6) Cover with wire retaining plate and tighten with
- Power supply unit 2 thumbscrews (Fig. 12).
- Accessory box including:
Dust cover Chinrest papers Handgrips (opition for patient use)
Spare fuses Focusing rod 1) Screw and attach Handgrips to both side of
Headrest (Fig. 13).

Fig. 5: Shipping container Fig .6: Lower container Fig. 7: Middle container

Fig. 8: Upper container Fig. 9: Unscrewing hex screw Fig. 10: Unscrewing thumbscrews
from Mounting plate from wire retaining plastic plate

Fig. 11: Assembling Headrest to Fig. 12: Fixing Headrest with Fig. 13: Attaching Handgrips (option)
Mounting plate wire retaining plate and thumbscrews
-7-
Assembling

Base, Microscope, Joystick Connecting plugs toTransformer

1) Place Base (Cross-slide base) and Microscope 1) Connect plugs to the receptacles at the back side
unit on tabletop. Engage the pinion to the rail. of the transformer(Fig. 16).
The rollers should engage the same pins on Plugs to be connected are; AC code, 8 cored cable
each tracks. for illumination adjustment, and banana connector.
Place the bottom of Joystick on the teflon plate.
2) Move Base (Cross-slide base) to forward / - Connect the main power plug to the three pins on
backward / left / right. the lamp housing cover.
Check the movement of Joystick - Connect the lamp plugs (black and red) to the black
and Base (Cross-slide base) is smooth. and red receptacles according to color code.
3) Install each Rack Cover (Fig. 1-4(27)) by sliding - Connect the two-pin plug to receptacle No.2.
it on the rail. - Connect the slit lamp base to the tranceformer
4) Attach Illumination unit to the shaft on the base using the eight core cable.(When you use the
sliding it carefully(Fig. 14.) digital camera attachment:L-0541DC, connect the
Tighten Illumination unit with retaining screw cable to receptacle No.3)
using supplied hex wrench(Fig 15).
Focusing
1) Insert the focusing rod in the pivot hole (Fig. 17).
Make sure the flat surfece of the focusing rod
㻮㼞㼑㼍㼠㼔㻌㼟㼔㼕㼑㼘㼐 should be perpendicular to the axis of the
microscope.
2) Remove caps from the eyepieces and objective
lenses.
3) Turn the instrument on.
4) Adjust the instrument to be in focus and the image
become clear while watching a narrow slit image
on the surface of the forcusing rod.

Breath shield
1) Attach breath shield to the microscope arm.
(Fig. 14)
Fig. 14: Installing Illumination unit

No.1 No.2 No.3

Fig. 15: Tightening Illumination unit

with retaining screw

Black Red
Fig. 16: Transformer case
(Rear View)

Fig. 17: Focusing rod

-8-
Base fixed

(1)Fixed to base
Attach the base to sturdy poles, supports, etc.

(2)Screw mounting
Securely fix with three screws (Fig. 18).

Fig. 18: fixed to base

Installation Environment

2.1Installation Environment

(1)Installation conditions
䞉Settheinstrumentin a placenotsubject to water.
䞉Setthe instrumentin aplacewhere there is no
fear of adverse effect due to atmospheric
pressure, temperature,humidity, ventilation,
sunlight, dust, salt, air containing ions etc.
䞉Stable environment must be maintained
avoiding inclination, vibration and impact etc.
䞉Do not setthe instrumentin a place where
chemicals are stored or gas is generated.

(2)Environmental conditions
䞉The operating environmental conditions below
must be required when installing the
instrument.

-9-
6. OPERATION
Adjusting P.D Adjusting Slit Width
1) Adjust the eyepeices diopter and the pupillary 1) Rotate either of Slit Width Control Knobs
distance before starting examination. (the control knobs of slit width) to vary the slit
2) If user is emmetropic, or is wearing a width(Fig. 20(12)).
diopter correction, focus the eyepieces at zero These knobs are also used as handles to rotate
by the illumination system to the left or right.
rotating the focusing rings (Fig. 1-4(6)), The angle between the microscope and the
until the index marks coincide with the 0 illumination system is adjustable from 0䜪 to 90䜪on
on the adjacent scales. If the operator is either side. This angle is indicated by Angle Scale
ametropic and is not wearing a correction, Ring(Figs. 1-4(22)). The scale on the left side of Slit
for each eye on the scale. Width Control indicates Slit Width(Fig. 21(12-A)).
If a significant amount of astigmatism is
present, the user should wear the spectacles Adjusting Slit Rotation and Slit Length
for correction to astigma. The projected slit image is rotated continuously
Adjust the interpupillary distance by graping around the optical axis verticaly and horizontaly
the prism housings (Fig. 1-4(5)), and rotating by the lever and the knob(Fig. 22(4)).
them to the correct value according to Click stops for slit angles is provided at 45䜪, 90䜪and
the scale below the right eyepiece. 135䜪(Fig. 22(4)).
3) Seat the patient facing to the headrest.
The patient lean forward, resting the forehead
on the headrest.
4) Adjust the height of the instrument by turning
Control for Chinrest(Fig. 1-4(14)).
(Adjust the hight of the chair, if necessary.)
The patient's eyes should be aligned with the
canthus mark.
5) Adjust the instrument base to the appropriate
position controlling with Joystick (Fig. 1-4(14)).
You can move the lamp and microscope
together in your required direction.
6) Press the main power swith to turn the Slit
Lamp on. Check the pilot lamp indicates
power is on(Fig. 19(F and E)).
Fig.20: (12) Slit Width Control Knobs
(Knobs for controling slit width)
Adjusting Illumination and Focus
1) Adjust the brightness of illumination by turning
Illumination knob (Fig. 19(D)).
2) Mount the illumination unit and adjust focusing -A
of the fixation lamp (Fig. 1-4(21)) to obtain the
desired patient's gaze direction.
3) Adjust focusing until the slit image is
is approximately nealy in focus to the naked
eye.
Adjust the focal point and the observing Fig. 21. (12-A) Slit Width Control Scale
positon by looking through the microscope Adjustable up to 20䜪in 5 steps
and controlling Joystick (Fig. 1-4(14)).

E
F
D

Fig. 19: Illumination Controls

D. Illumination Knob
E. Pilot Lamp Fig. 22: (4) Slit Rotation Control Lever &
F. Main Power Switch Slit Length Control Knob

-10-
Tilting Illumination System Types of Illuminations
By pressing down the latch, the illumination system Except for direct forcal illumination such as,
is tilted down with the angle up to 20 in 5䜪steps. retro-illumination, indirect illumination and
(This is valuable in the examination using lateral scanned illumination, it is easy to
gonioscopy and the fundus examinations.) controll illumination system.
1) Press down the latch and pull the illumination 1) Loosen the Centering Screw(Fig. 27(9)).
base toward the operator until the tilt reach 2) Rotate the optical center of the illuminating
to the appropriate tilt stop position (Fig.24). system.
2) Release the latch to fix the illumination at For normal use, the slit image is automatically
required tilt stop position. back to the center by tightening the screw.

Fig. 23: (11) Latch

Fig. 25: Illumination System Controls
(3) Filter Disc Lever
(4) Aperture Disc Control Knob
(Knob for controling aperture disc)

Fig. 24: Tilting the system

The illumination system also contains a filter disc

and an aperture disc. Fig. 26: (2)Slit Length Scale

Filters
The filter disc is controlled by Filter Disc Lever(Fig.
25(3)). This disc contains filters and each filter is
located in the following order : Cobalt blue filter (for
fluorescein examinations), Unfiltered (Opened
aperture), Heat absorbing filter, 50% neutral density
filter and Red free filter.

Aperture for Adjusting Slit Length

The aperture disc is controlled by turning the knob
for controling aperture disc (Fig. 25(4)).
Turn the knob to adjust the length of the projected
slit image(Fig. 25(4)). Apertures with fixed diameters
are provided in 10, 6, 4, 3, 1 and 0.2mm. The Fig. 27: (9) Centering Screw
wedge-shaped diaphragm is controlled with Aperture (12) Slit Width Control Knob
Disc Control Knob (Fig. 25(4).) The Slit length is (Knob for controling slit width)
continuously variable from 0 to 10mm. The slit
length is indicated by scale (Fig. 26(2)).

-11-
Magnification Control

L-0187
L-0185
Converting the eyepieces total Converting magnification with
magnifications with lever under tube (8) Magnification Control Knob
Total magnification rate: 10x,16x, 25x L-0187: Total magnification rate: 10x,16x, 25x
L-0189: Total magnification rate: 6x,10x,16x,25x,40x

The magnification is controlled by the knob (Fig.

28(8)). The objective lenses are parfocal and the
working distance is constant for any magnification.
As long as the microscope is focused at the
highest magnification, it is also in focus at all
lower magnifications.

L-0240
Converting magnification with
(8) Magnification Control Knob
Total magnification rate: 10x - 30x continuous

Fig. 28: Magnification Control

䒇
䑻

Fig. 29: Instrument Base Fig. 30: Positioning the Hruby Lens
(22) Angle Scale Ring (H) Hruby Lens(option)
(23) Angle Index Ring (S) Slide
(24) Illumination Arm Lock (G) Guide Plate
(25) Microscope Arm Lock

-12-
Locking rotations
You can lock the lateral movement of the
instrument base by tightening the screw (Fig.
29(26)).

The microscope and illumination system can

be rotate independently or simultaneously
on the vertical pivot axis.
- The two systems are moved together with
at any fixed angle between them by
tightening the knob for Illumination Arm
Lock(Fig. 29(24)).
- To fix the rotating microscope system,
tighten the knob for Microscope Arm
Lock(Fig. 29(25)).
- If you want to rotate only the illumination
system, tighten the knob for Microscope
Arm Lock and loosen Illumination Arm
Lock (Fig. 29(25 and 24)).

Angle between Micrscope & Illumination

Angle Scale Ring and Angle Index Ring
indicate the angle between the micrscope
and illumination systems (Fig. 29(25 and
24)).
Click stops are provided at 0°, 10° to the
right and 10° to the left orientation.

Hruby Lens (Option)

Examinations of the posterior vitreous
detachment and the fundus oculi can be
performed either with the fundus contact
lenses or with the Hruby Lens (option).
For the initial orientation, use relatively low
magnification and low illumination. When
using the optional Hruby Lens, Slide and
Guide Plate are available(Fig. 30(S and G)).
The hruby lens will be followed to the every
movement of the slit larnp accordingly.
The fine adjustment of the hruby lens is
required during the examination.

Illumination intensity
Normally, the control of illumination is set for
the appropriate slit illumination for the the
examination.
- To mixmize the illumination intencity,
keep pressing the right button
on the base(Fig.31).
- To adjust the illumination intencity,
turn the knob on the base.

-13-
7. MAINTENANCE
Cleaning Chinrest paper replacement
1) Clean the chinrest with 70% ethanol for
Mirror cleaning disinfection.
Remove dust accumulation with a camel's 2) Replace the old chinrest paper with a new
hair brush. Then, remove fingerprints with one.
cotton swab soaked in isopropyl alcohol. Dry
the mirror with a soft facial tissue. Mirror replacement
1) Tilt the illumination system by releasing
Eyepiece cleaning
Latch (Fig. 23(11)).
Follow the same procedure as mirror
cleaning to remove fingerprints on eyepiece. 2) Pull upward and pull out the mirror
However, use as little alcohol as possible for holding the narrow edge of the mirror.
cleaning the eyepieces. (Fig. 37).
3) Replace the old mirror with a new one.
Equipment surface cleaning 4) Set back the tilt of the illumination system
Clean the equipment surfaces, especially the to the original position.
joystick glide plate, by wiping with a soft dry
cloth. Do not use comrnerical or household
cleaners.

Replacement
Main lamp replacement
The main lamp is a tungsten or halogen lamp
which have long lifetime without blackening of
the glass envelope. When it is eventually
needed to replace the lamp, follow the
procedure below for the quick and easy
replacement.
CAUTION
Fig. 33: Fig. 34: Removing
Allow sufficient time for the lamp to be cool
(19) Lamp Housing Cover (1) Lamp Housing Cover
before replacing. Metal and glass parts of the
lamp could be too hot to burn the fingers even Retaining Nuts
if the instrument has been used only for short
period.

1) Loosen 2 retaining nuts for lamp housing

cover (Fig. 33(19)).
2) Remove the lamp housing cover.
(Fig. 34(1)).
3) Remove the old lamp and replace it with
a new one (Fig. 35-36)
The lamps are pre-focused and aligned.
4) Engage the notch of lamp base and the Fig. 35: Removing light bulb Fig. 36: Installing light
tab on the lamp housing (Fig. 36(35)).
5) Cover the lamp housing cover pressing
down it againt the spring force.
Tighten it with 2 retaing nuts.

Fixation Lamp (Option)

1) Remove the front part of the fixation unit by
rotating it counterclockwise.
2) Unscrew 2 screws.
3) Rremove the old battry and replace it with
a new one.
4) Reassemble the front part by pushing and
turning it clockwise.

Fig. 37: Mirror replacement

-14-
Base Sheet Replacement

1) Unscrew 3 screws of the base and pull out the sheet under the plastic cover.
2) Turn over the sheet and set it back to the original positon on the base.
3) Put the plastic cover on the sheet and tighten it with screws.

Screws

Plastic cover

Sheet

Fig. 38: Replacement of sheet

8. Electrical Wiring Diagrams

-15-
Sept 2018. Rev.11