Scribd Logo
Upload

Welcome to Scribd!

  • 78 views

    Nf528t Rev.0

    Uploaded by

    MZY Commercial Enterprises
    ADMERTM NF528T is an anhydride modified L-LDPE based adhesive resin designed to bond PE and EVOH together in co-extrusion applications such as blown film, cast film, and blow molding. It can also bond PE and aluminum together in heat lamination applications. The resin has a melt flow rate of 1.8 g/10 min, density of 0.91 g/cm3, tensile strength of 12 MPa, and elongation at break over 500%. Processing temperatures between 200-230°C are suggested, with a maximum of 300°C and minimum of 180°C.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Nf528t Rev.0

    Uploaded by

    MZY Commercial Enterprises
    78 views1 page
    ADMERTM NF528T is an anhydride modified L-LDPE based adhesive resin designed to bond PE and EVOH together in co-extrusion applications such as blown film, cast film, and blow molding. It can also bond PE and aluminum together in heat lamination applications. The resin has a melt flow rate of 1.8 g/10 min, density of 0.91 g/cm3, tensile strength of 12 MPa, and elongation at break over 500%. Processing temperatures between 200-230°C are suggested, with a maximum of 300°C and minimum of 180°C.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    ADMERTM NF528T is an anhydride modified L-LDPE based adhesive resin designed to bond PE and EVOH together in co-extrusion applications such as blown film, cast film, and blow molding. It can also bond PE and aluminum together in heat lamination applications. The resin has a melt flow rate of 1.8 g/10 min, density of 0.91 g/cm3, tensile strength of 12 MPa, and elongation at break over 500%. Processing temperatures between 200-230°C are suggested, with a maximum of 300°C and minimum of 180°C.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    78 views1 page

    Nf528t Rev.0

    Uploaded by

    MZY Commercial Enterprises
    ADMERTM NF528T is an anhydride modified L-LDPE based adhesive resin designed to bond PE and EVOH together in co-extrusion applications such as blown film, cast film, and blow molding. It can also bond PE and aluminum together in heat lamination applications. The resin has a melt flow rate of 1.8 g/10 min, density of 0.91 g/cm3, tensile strength of 12 MPa, and elongation at break over 500%. Processing temperatures between 200-230°C are suggested, with a maximum of 300°C and minimum of 180°C.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    ADMERTM

    NF528T
    Linear Low-Density Polyethylene (L-LDPE) Based Adhesive Resin

    GENERAL DESCRIPTION
    ADMERTM NF528T is an anhydride modified L-LDPE based adhesive resin, which is primarily designed to bond PE and
    EVOH together in co-extrusion blown film applications. It is also used in co-extrusion processes such as cast film, cast sheet,
    blow molding, tubing and pipe applications. ADMERTM NF528T is also designed to bond PE and Aluminum (AL) together in
    heat lamination applications.

    TYPICAL MATERIAL PROPERTIES


    Property Typical Value Units ASTM Test Method
    Melt Flow Rate (@ 190 ºC) 1.8 g/10 min. ASTM D1238
    Density 0.91 g/cm3 ASTM D1505
    Stress at Yield Point 7 MPa ASTM D 638
    Tensile Strength at Break 12 MPa ASTM D 638
    Elongation at Break >500 Percent (%) ASTM D 638
    Shore Hardness 40 D – Scale ASTM D2240
    Vicat Softening Point 69 ºC ASTM D1525
    Melting Point 120 ºC ASTM D3418

    Adhesion Strength to EVOH


    - 5 layer Blown Film: PE/AD/EVOH/AD/PE
    30μ/5μ/5μ/5μ/30μ (@ 15m/min) 8 N/15mm T-Peel Method, 300mm/min

    - 3-layer Heat Sealed Sheet: AL/AD/AL


    200μ/100μ/200μ
    Heat Seal Condition: 140℃*0.1MPa*60s 95 N/20mm 180°-Peel Method, 200mm/min
    160℃*0.1MPa*60s 110 N/20mm 180°-Peel Method, 200mm/min

    PROCESSING PARAMETERS
    Processing temperatures of between 200ºC and 230ºC are suggested for initial evaluations. Maximum processing temperatures
    should not exceed 300ºC. Minimum Temperatures should not fall below 180ºC. Additional processing suggestions shall be
    given when a customer’s equipment and process conditions are known. Contact your Mitsui Chemicals Sales Representative
    for additional information.

    FOOD CONTACTING REGULATORY STATUS*


    1. FDA (USA)
    ADMERTM comply with Federal Food, Drug and Cosmetic Act and 21 CFR Section 175.105 (Adhesives).
    2. EU Directive (Europe)
    The starting monomers and the additives contained in ADMERTM are listed as authorized in the EU Plastics Directive
    2002/72/EC and/or its amendments 2004/1/EC, 2004/19/EC, 2005/79/EC, 2007/19/EC and 2008/39/EC. (Some of the
    components have specific migration limits.)
    3. National Standard of the P.R.C. (China)
    The base PE and PP resin of ADMERTM comply with GB9692 and GB9693 respectively. The contained additives are listed in
    GB9685-2008 (Provisional list).
    4. JHOSPA (Japan)
    ADMERTM grades made in Japan comply with “the self-restrictive standards for food contacting package – container and
    utensil made of polyolefins and certain polymers” of Japan Hygienic Olefin and Styrene Plastics Association.
    *For further information and details, please contact our sales representatives, since there are some exceptional cases.

    The information contained herein is, to the best of our knowledge, accurate and reliable. However, since the actual conditions of use(s) of our products are
    beyond our control, IT IS THE USER’S RESPONSIBILITY TO ASSUME ALL RISKS OF SUCH USE(S) FOR SPECIFIC APPLICATIONS. Mitsui
    Chemical makes no guarantees of results and assumes no liability in connection with its recommendations or suggestions. Nothing contained herein shall be
    construed as a recommendation for use in violation of any patents or of applicable laws and regulations. SAMPLES ARE PROVIDED WITHOUT ANY
    WARRANTIES, EXPRESSED OR IMPLIED.

    You might also like