GYRO COMPASS REPEATER COMPASS AND ACCESSORIES @ OPERATOR'S MANUAL FEBRUARY 1993CONTENTS: Page GENERAL. i DESCRIPTION POR EACH UNIT 2 2-1 Repeater Conpass ... 2 2-2 Open Scale Repeater Compass ... 4 2-3 G. C. P. Repeater Compass 6 2-4 Repeater Stand BH type 8 2-5 Repeater Mounting BB Type and Junction Box . 2-6 Repeater Mounting KB Type and Junction Box .......-..++5 10 2-7 Junction Box for RDF (Radio Direction Pinder) . 2-8 Azimuth Circle 2-9 Shadow Pin 2-10 Repeater Cover 2-11 Repeater Shading Plate .. OPERATION .. MAINTENANCE AND INSPECTION TROUBLESHOOTING ATTACHED DRAWING External Dinensions of Repeaters and AccessoriesGENERAL The repeater compass receives the ship's heading bearing signal transmitted from the master compass, bearing. and remotely indicates the The repeater compass contains a torque synchro motor or a step wotor with which the repeater conpass card is rotated through the gear train. It is possible to use even in the night as the card is illuminated by the lamp which can be adjusted in brightness fron the outside. The following types of repeaters are provided. Type Name Specification RP-11-2 | Synchro repeater | AC 100/110 ¥ 0/60 Hz Synchro notor RP-18-1 | Synchro open AC 100/110 ¥ 50/60 Hz Synchro motor scale repeater 30x RP-L4-1 | Synchro G. CP | AC 100/110 ¥ 50/60 Hz Synchro repeater notor 90X RP-21-2 | Step repeater De 70 V step motor 90X RP-SI-1 | Step repeater De 35 V step motor 90x RP-A1-1 [Step repeater | DC 24 V step notor 90x And, the following accessories are also provided. Type Name Specification BH-L1-1_| Repeater stand Bil type for synchro repeater Bil-2i-1_| Repeater stand BI type for step repeater BB-11-L_| Repeater mounting BB type | for synchro repeater BB-21-1 | Repeater mounting BB type | for step repeater wp-11-1 | Repeater mounting MB type | for synchro repeater MB-21-1 | Repeater mounting MB type | for step repeater Junetion box for RDF Azimuth circle Shadow pin Repeater cover Repeater shading plate2. DESCRIPTION FOR EACH UNIT 2-1 Repeater Compass (Type RP-11-2, RP-21-2, RP-31-1, RP-41-1) The repeater conpass is used to measure the bearing or to steer the ship, and the case is nade of FRP (fiber reinforced plastic) and is water-proof construction abled to use even in the open deck. For PR-11-2, the torque synchro notor with AC 100/110 V, 1%, 50/60 lz is contained in the case. Por RP-21-2, RP-31-1, RP-41-1, the step motor instead of the synchro motor is containec in the case. The gear train with 1/90 ratio is mounted between the motor and the card. On the repeater card, 360 degrees with every one degree aro graduated (1X). There are two illumination lanps for the card below the repeater card. In the side of the repeater case, there is a synchronizing knob which synchronizes the repeater compass bearing with the master compass bearing, and is a hole and a screw hole to mount the repeater case on the repeater stand BH type or on the repeater mounting HB type. There is a bezel ring for the azimuth circle at the top of the repeater case. The bezel ring fixes the surface glass on the case together with the packing The seat for the shadow pin is adhered at the center of the surface glass. At the bottom of the repeater case, the cabtire cable (1-8 a) with the packing for the water-proof gland is connected. {Electric parts] syabol_| Draving Now Wane Renarks B701 | 10350133- | Torque synchro motor | for RP-11-2 4701 | 10359030- DC 70 V 90X step motor | for RP-21-2 10359058- DC 35 V 90X step notor| for RP-31-1 10359005- | DC 24 V 90X step notor Seen 2032 ge 115V pve see ae (for RP-11-2, 21-2) 10004345- | Lanp 45 V 5 Le (for RP-31-1, 41-1)THE SEAT FOR THE SKADOW F y+ F Boe Bek NAME | REPEATER S wi ve- 9 TYPE | RP-11~2, RP=21-2 S85 | RP-31-1, RP-41-1 MASS | a | 4 OK NO, NAME tH 1_|SYNCHRONTZING_KNOB|faa/7 2 _[CASE(F. R. P) 5-2(FRP) 3 [BEZEL RING (BRONZE) | ¥47 (Ai@) 4 [COVER(F. R. P) a (FR) BTIRE CABLE 1, 8m SUPPLIED BY TOKIMEC a4¥r- FHT, Bm FF STEP MOTOR = wot eye ye ruroi rime} reroi ru102 sano ro salclels DOCOMO} miele aa es VE- STARE (STEP MOTOR TYPE) ve-gayitaieain = (SYNCHRO MOTOR TYPE) (AFYIE-FH) (Y790E- FR) CIRCUIT DIAGRAMS B2-2 Open Scale Repeater Compass (type RP-13-1) It is convenient to use the open scale repeater compass for steering because the scale of the compass card is magnified. The repeater case is nade of FRP and can be used in the open deck because of the water-proof construction. In the case, the torque synchro motor with AC 100/110 V, 1@, 50/60 liz is contained. The gear train is mounted between the motor and the card. The card graduation of the open scale repeater is magnified 5 times that of the normal repeater. There are two illumination lamps for the card below the repeater card. In the side of the repeater case there is a synchronizing knob which synchronizes the repeater conpass bearing with the naster compass bearing, and is a hole and a screw hole to mount the repeater case on the repeater mounting. A part of the repeater card can be seen through the surface glass at the top of the repeater case. At the bottom of the repeater case, the cabtire cable (1-8 m) with the packing for the water-proof gland is connected. [Electric parts] cimea’ | Drawing No- Nane Remark B701 | 10350133- | Torque synchro notor PL701 081012032 Lamp KPIS V5 W PL702 (for RP-11-2, 21-2)RUBBER LINE & ® NAME | OPEN SCALE REPEATER % & |*-FvAy-w VE-F TYPE | pp-13- mee 13-1 MASS | 4. 5K. wisp | 4 5Ke NO, NAME 4 f 1_[ SYNCHRONIZING KNOB] gi 2_[ CASE (F. R. P) 5-2.(FRP) 3 [BEZEL RING (BRONZE) | Y77 (8m) 4 [COVER(F. R. P) K—(FRP)| CAB CABLE 1, 8m SUPPLIED BY TOKIMEC Fe IIIVS-JW1, Bm hEADD GENERAL VIEW ah ah | puoi Put0e |TS4N60. 8701 | | | | Lo “To THE REPEATER COMPASS JUNCTION BOX bes aorta CIRCUIT DIAGRAMS % 8 Jape2-3 G. C. P Repeater Compass (Type RP-14-1) G. C. P repeater compass is used for the course sensing signal in the automatic steering of the auto pilot (gyro). The repeater case is nade of FRP and is water-proof construction. The torque synchro motor with AC 100/110 V, 1, 50/60 Hz is contained in the case. The gear train with 1/90 ratio is mounted between the motor and the repeater card. On the repeater card, 360 degrees with every one degree are graduated. The magnet bar for sensing the course signal is contained in the cover at the center of the compass card. This magnet bar generates signal for the course sensing in the pick off coil in the control unit for the automatic steering (refer to the separate manual). There are two illuminaticn lamps for the card below the repeater card. In the side of the repeater case, there is a synchronizing knob which synchronizes the repeater compass bearing with the master compass bearing, and is a hole and a screw hole to nount the repeater case on the repeater mounting. At the botton of the repeater case, the cabtire cable (1.8 m) with the packing for the water-proof gland is connected. (Electric parts] Circuit synbol | Dravine No- Name Remark B70L 10350133- Torque synchro motor PL701 | 081012032 | Lamp KPIS V5 PL702 (for RP-11-2, 21-2)RUBBER LINE ® NAME | GCP_REPEATER & wl ocp ve-9» TYPE | pp-y4- weg | RPo14-1 MASS vg | 4: 9Ko ee NO. NAME a & 1_[SYNGHRONIZ ING_KNOB] Faa/F 2 _[CASE(F, RP) 5-2(FRP)| 3 [BEZEL RING (BRONZE) | V7 (7m) 4 [COVERCF. RP) au (FRP)| 5_[CONTROL_UNIT ee 6 [MAGNIFYING GLASS [Ai CABTIRE GABLE 1, 8m SUPPLI Fr SPIT-IW1, Om PIIGD GENERAL VIEW * # a SYNCHRO MOTOR 5 Be 1 PL701 L702 frsanoo t 8701 (23) (SYNCHRO MOTOR TYPE) 1 (7908-98) | GIRCUIT DIAGRAMS % TO THE REPEATER COMPASS JUNCTION BOX besa2-4 Repeater Stand BH type (Type BH-11-1, 21-1) It is a stand to support the repeater compass when the repeater compass is installed on the deck. The stand body is made of FRP and has corrosion resistance abled to use in the open deck. It has a gimbal ring at the upper part of the stand to support the repeater compass horizontally even when the whip is rolling and pitching. At the middle part of the stand, there is a repeater switch and a dinner for illumination. (Electric parts] Circuit synbol | Drawing No. Name Remark R701 | 10010896- | Variable resistor | 1kQ 50W S701 11160036 - Toggle switchNAME | REPEATER STAND BH TYPE 2 Of BH Mb Em AE TYPE | BH-11-1 MASS: 16Ka ates | BH-21-1 fi @ NO, NAME a STAND (FR, P) | A9UK (F.R.P) HELMET (F,R,P) [Auxyh (FR, PD] REPEATER ve-9 DIMMER ed REPEATER SWITCH) LU-92494 CABLE GLAND 250] RiNRIRRWZ% 254) GENERAL VIEW * BR olen] a |eo|no|— a | ! | ota i eet | to me [ . L +r) | REPEATER: ‘ i R70 10 THe REPEATER Coens ConASS vedo 2X3LAXEXE] | _vessaoin OTHE ROGONPASS RELATING THE GYROCOWPASE RELATING Toe ao ‘TERI NAL’ BOARD. Te OTD, PRI YNCH R_ TYPE: (STEP MOTOR TYPE) . peepee s) ) AFVIE-IK) Gee CIRGUIT DIAGRAM ao eB B Fed, RTA aay 32-5 Repeater Hounting BB Type and Junction Box (Type BB-L1-1, 21-1) This mounting has a gimbal ring to support the repeater compass horizontally when the ship is rolling and pitching. ‘The repeater conpass is supported with the pins in the gimbal ring, and the gimbal ring is fixed on the junction box. The junction box consists of a repeater ‘switch, a dinner for illumination and terminal boards to which the signal cable fron the master compass and the cable to the repeater conpass are connected. [Electric parts] Circuit syabol | Drawing No- Nane Remark R701 10010896 - Variable resistor 1kQ 504 $701 11160036- Toggle switch 2-6 Repeater Mounting MB Type and Junction Box (Type MB-11-1, 21-1) The repeater mounting Mi type can support the repeater compass at a tilt with mounting screws. It can be used for ship’s steering and watching. The junction box has the sane dimensions as those of BB type and fixes the repeater mounting. The junction box consists ofa repeater compass switch, a dinner for illumination and terminal boards to vhich the signal cable fron the master compass and the cable to the repeater compass are connected. {Electric parts] Circuit synbol | Drawing No Name Renark R701 10010896- | Variable resistor | 1 KQ 50 W 8701 | 11160036- | Toggle switch = agesWAME | REPEATER MOUNTING 8B TYPE & Ree ve FRAE Type | BB-1 1-1 ates | BB-21-1 MASS Bea | & TKo WANE | REPEATER MOUNTING MB TYPE 2 &|M oe ve-FRNE 2% NO [ NAME DINER REPEATER SWITCH] LY=pat9F CABLE GLAND 250 | MARSIRARH 250) REPEATER, ve-2 oa ro ne [EE ane GENERAL VIEW eo ee “TO THE {OGOMPASS. RELAYING TERMINAL BOARD FeAOKNT OORT (STEP MOTOR TYPE) (259 FE- IR) oe “TO THE GYROCOMPASS RELAYING TERMINAL BOARD Yed034N2, $MEA (SYNCHRO MOTOR TYPE) (9990E-9R) CIRCUIT DIAGRAM a ® eee2-7 2-8 2-10 2-1 Junction Box for RDF (Radio Direction Finder) This is a relaying junction box for transmitting the naster conpass bearing signal to a radio direction finder, and has a relaying terninal board in the case. Azimuth Circle The azimuth circle is placed on the bezel ring of the repeater compass to support the repeater compass horizontally with two levels. In this condition, astronomical observation can be made with the mirror and the slit located on the azinuth circle, and measurement of objects with the lubber’s line and the slit. Shadow Pin The shadow pin is used for astronomical observation or neasurement of objects by standing the pin in the seat at the center of the surface glass of the repeater compass which is mounted on the repeater stand BH type or the repeater nounting BB type. Repeater Cover It protects the glass by placing on the repeater conpass when the repeater compass mounted in the repeater stand BB type is not used. Repeater Shading Plate When the bearing repeater mounted in the repeater stand BB is used, this plate shades direct rays of the sun for easier reading. SaiNAME | JUNCTION BOX FOR RDF ois BoM RF DwG NO }1o00621 30) gS neg Ba {0-9ko NAME [ AZIMUTH CIRCLE Ti 1 sonal 5S @ © Gr NB ftoosoo0a0] 55 [2.2Ks | 9 NO,[ NAME | &_ FINDER WA MIRROR it PRISM & LENS| JAK AU UIA oO PRISM yA i t wae PSunoow Pin] 2. [wane [a é & wlyrkoey 1 [seat |e DWE NOT rogson1s0| 2 [Pin le a # 3 [rin [ey 8 NAME [REPEATER COVER & Bye - 9a - WG NO MASS a gfe |e 0,5Ko no, | NAME [% 1 [oover | an 2 [KNos [99s Tune [RPENTER SusooW PLATE C) \ We a aly e - 9 @ % 8 DWE NOT; 591 92380] MASS 0. ako = 13 =3. OPERATION Turn OFF the repeater switch, and synchronize the repeater card with the reading of the master compass by the synchronizing knob. Turn ON the repeater switch. The repeater card is synchronized with the master compass at every 4 degrees. Make sure the complete synchronization. If there is any difference between the two readings, synchronize again. 4, MAINTENANCE AND INSPECTION Routine Inspection Hake sure the repeater compass reading coincides with that of the master compass. Maintenance Apply grease sometimes on the gimbal shaft of the repeater nounting BB type and Bi type to rotate the gimbal smoothly. When the inside surface of the repeater glass is dim, select a fine and dried day, and open the back cover of the repeater conpass and leave as it is for several hours. Close the cover when the water drop inside the glass has disappeared. To replace the lamp, open the back cover of the repeater conpass and replace the lamp inserted in the socket. Periodical Inspection Many packings for water-proof construction are used in the repeater compass. These packings deteriorate while using for a Jong tine. It is recommended to replace packings at the periodical inspection for the gyro compass. 5. TROUBLESHOOTING The repeater reading does not agree. Check the repeater fuse in the master compass, and synchronize the readings. i. [anThe repeater does not follow up. Check the repeater fuse in the master conpass. When the fuse is normal, contact the service station to replace the repeater motor. Illumination is no good. Open the back cover of the repeater compass and replace the lamp inserted in the socket with a spare lamp. Inside surface of glass is d: Open the back cover of the repeater conpass in a fine and dried day, and leave as it is for several hours. Glose the cover when the water drop inside the glass has disappeared. = ese