Revo 4

General Information
Unpacking: Thank you for purchasing the Revo 4 by American DJ®.
Every Revo 4 has been thoroughly tested and has been shipped in
perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect your fixture for any damage and be
sure all equipment necessary to operate the unit has arrived intact. In
the event damage has been found or parts are missing, please contact
our toll free customer support number for further instructions. Please
do not return this unit to your dealer without contacting customer sup-
port first.
Introduction: The Revo 4 can be a four or 256 channel, DMX intel-
ligent LED fixture. The fixture has three different operating modes;
sound-active, show mode, DMX controlled. The Revo 4 has twelve
shows to choose from. The unit can be used as a stand alone unit or in
a master/slave configuration. For best results use fog or special effects
smoke to enhance the beams projections.
Customer Support: American DJ® provides a toll free customer
support line, to provide help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: [email protected]
To purchase parts online visit http://parts.americandj.com

User Instructions Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
WARNING! Due to the magnifying type lens, please keep Warning! This may cause severe eye damage. Avoid looking directly
the lens out of contact with direct sunlight. Direct sunlight into the light source at all times!
can cause heat to build up inside of the unit, which will
seriously damage unit.

Rev. 2/10 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 2

Revo 4 General Instructions Revo 4 Safety Precautions
To optimize the performance of this product, please read these For Your Own Personal Safety, Please Read and Understand This
operating instructions carefully to familiarize yourself with the basic Manual Completely Before You Attempt To Install Or Operate
operations of this unit. These instructions contain important safety This Unit!
information regarding the use and maintenance of this unit. Please • To reduce the risk of electrical shock or fire, do not expose this unit
keep this manual with the unit, for future reference. rain or moisture
Revo 4 Features • Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
• DMX-512 Protocol Compatible (Four or 256 DMX Channels) age for your unit.
• RGB + White • Do not attempt to operate this unit if the power cord has been
• 3 Operating Modes - Show Mode; Sound Active; DMX Controlled frayed or broken.
• Stand Alone or Master/Slave Configuration • Do not attempt to remove or break off the ground prong from
• Internal Microphone the electrical cord. This prong is used to reduce the risk of electrical
• Digital Display for Address and Function Setting shock and fire in case of an internal short.
• UC3 Controller (Not Included) • Disconnect from main power before making any type of connection.
• 12 Show Modes • Do not remove the cover under any conditions. There are no user
Revo 4 Warranty Registration serviceable parts inside.
• Never operate this unit when it’s cover is removed.
The Revo 4 carries a 3 year (1095 days) limited warranty. Please fill
• Always be sure to mount this unit in an area that will allow proper
out the enclosed warranty card to validate your purchase and war-
ventilation. Allow about 6” (15cm) between this device and a wall.
ranty. You may also register your product online at www. americandj.
• Do not attempt to operate this unit, if it becomes damaged.
com. All returned service items whether under warranty or not, must
• This unit is intended for indoor use only, use of this product out-
be freight pre-paid and accompany a return authorization (R.A.) num-
doors voids all warranties.
ber. If the unit is under warranty you must provide a copy of your
• Always mount this unit in safe and stable matter.
proof of purchase invoice. Please contact American DJ® customer
• Power-supply cords should be routed so that they are not likely to
support for a R.A. number.
be walked on or pinched by items placed upon or against them,
Revo 4 Handling Precautions paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
Caution! There are no user serviceable parts inside this unit. Do not • Cleaning -The fixture should be cleaned only as recommended by
attempt any repairs yourself, doing so will void your manufactures war- the manufacturer. See page 15 for cleaning details.
ranty. In the unlikely event your unit may require service please contact • Heat -This fixture should be situated away from heat sources such
American DJ®. as radiators, heat registers, stoves, or other appliances (including
American DJ® will not accept any liability for any resulting damages amplifiers) that produce heat.
caused by the non-observance of this manual or any unauthorized • The fixture should be serviced by qualified service personnel when:
modification to this unit. A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.

American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 3 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 4
 Revo 4 Set Up Revo 4 Set Up
Power Supply: Before plugging your unit in, be sure the source volt-
REMOTE INPUT OUTPUT REMOTE INPUT OUTPUT

shielded cable (This cable may be purchased at almost all professional

SOUND CONTROL SOUND CONTROL SOUN
INPUT INPUT

age in your area matches the required voltage for your American DJ® sound and lighting stores). Your cables should be made with a male
Revo 4. The American DJ® Revo 4 contains a electronic ballast, which and female XLR connector on either end of the cable. Also remember
will auto sense the voltage when it is plugged into the power source. that DMX cable must be daisy chained and cannot be split.
With the electronic ballast you do not need to worry about wall volt-
age, this unit can be plugged in anywhere. Also be sure to only use the POWER POWER

included I.E.C. power cable supplied with the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro- Notice: Be sure to follow figures two and three when making your own
DMX512

tocol used by most lighting and controller manufactures as a form of cables. Do not use the ground lug on the XLR connector. Do not con-
DMX+,DMX-,COMMON

communication between intelligent fixtures and controllers. A DMX nect the cable’s shield conductor to the ground lug or allow the shield
controller sends DMX data instructions from the controller to the fix- conductor to come in contact with the XLR’s outer casing. Grounding
ture. DMX data is sent as serial data that travels from fixture to fixture the shield could cause a short circuit and erratic behavior.
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
COMMON
fixtures (most controllers only have a DATA “OUT” terminal). 1 DMX + 1 1
Termination
avoids sign
DMX512 OUT DMX512 IN
3 3 3 and interfere
DMX Linking: DMX is a language allowing all makes and models
3-PIN XLR 2 DMX - 3-PIN XLR
2 2 to connect a
120 Ohm 1/4
of different manufactures to be linked together and operate from a Figure 2 and PIN 3 (

single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using XLR Male Socket XLR Female Socket XLR Pin Configuration
several DMX fixtures try to use the shortest cable path possible. The 1 Ground 2 Cold 2 Cold 1 Ground Pin 1 = Ground
order in which fixtures are connected in a DMX line does not influence
SOUND
REMOTE
CONTROL
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT OUTPUT

Pin 2 = Data Compliment (negative)

the DMX addressing. For example; a fixture assigned a DMX address
INPUT INPUT INPUT

of 1 may be placed anywhere in a DMX line, at the beginning, at the 3 Hot 3 Hot Pin 3 = Data True (positive)

end, or anywhere in the middle. Therefore, the first fixture controlled Figure 3
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located POWER
Special Note: Line Termination. When longer runs of cable are
POWER POWER

in the DMX chain. used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
Data Cable (DMX Cable) Requirements (For DMX DMX512
DMX+,DMX-,COMMON nected between pins 2 and 3 of a male XLR connector (DATA + and
and Master/Slave Operation): The Revo 4 can DATA -). This unit is inserted in the female XLR connector of the last
be controlled via DMX-512 protocol. The Revo 4 unit in your daisy chain to terminate the line. Using a cable terminator
can be a four or 256 channel DMX unit. The DMX (ADJ part number Z-DMX/T) will decrease the possibilities of erratic
address is set electronically using the controls on behavior.
the rear panel of the unit. Your unit and your DMX COMMON
controller require a approved DMX-512 110 Ohm DMX512 OUT DMX +
1 1 1
Termination reduces signal errors and
avoids signal transmission problems
3 DMX512 IN 3 and interference. It is always advisable
Data cable for data input and data output (Figure
3
3-PIN XLR DMX -
2 3-PIN XLR
2 2 to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
1). We recommend Accu-Cable DMX cables. If you Figure 1 and PIN 3 (DMX +) of the last fixture. Figure 4
are making your own cables, be sure to use standard 110-120 Ohm
American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 5 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 6
Revo 4 Set Up Revo 4 System Menu

5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting stan-
dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 3-Pin XLR Female (Out) 5-Pin XLR Male (In)

Ground/Shield Pin 1 Pin 1
Data Compliment (- signal) Pin 2 Pin 2
Data True (+ signal) Pin 3 Pin 3
Not Used Pin 4 - Do Not Use
Not Used Pin 5 - Do Not Use

American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 7 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 8
Revo 4 System Menu Revo 4 System Menu

ADDR - DMX Address Setting. SOUN - In this mode you can run the unit in sound active
mode
1. Tap the either the MENU, UP, or DOWN buttons until “ADDR”
is displayed, press ENTER. 1. Tap the MENU button until “SOUN” is displayed, press
ENTER.
2. “1” will now be displayed and flashing. Press the UP or
DOWN buttons to find your desired address. Press ENTER to 2. Either “ON” or “OFF” will now be displayed. Press the UP or
set your desired DMX address. DOWN buttons to select one or the other.

CHND - This will let you switch between 4 Channel DMX BLND - Blackout or Stand by mode.
mode and 256 Channel DMX mode. 1. Tap the either the MENU button until “BLND” is displayed,
1. Tap the either the MENU button until “CHND” is displayed, press ENTER. Either Yes or No will be displayed.
press ENTER. Either “4CH” or “256C” will be displayed 2. To activate Blackout tap the UP or DOWN buttons until Yes is
2. Tap the UP or DOWN buttons to choose your desired DMX displayed, press ENTER to confim and exit. The fixture will now
mode and press ENTER to confim and exit. be in Blackout mode. To deactivate Blackout mode, select No
and press Enter.
SLND - This will let you set unit as a master or slave in a LED - With this function the LED display will turn off after
master/slave configuration.
2 minutes.
1. Tap the either the MENU button until “SLND” is displayed,
1. Tap the either the MENU button until “LED” is displayed,
press ENTER. “MAST”, “SL 1” or “SL 2” will be displayed.
press ENTER.
2. Tap the UP or DOWN buttons until your desired setting is
2. The display will show either “ON” or “OFF”. Press the UP or
displayed, press ENTER to confim and exit.
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to allow the LED display to turn off after 2 min-
SHND: SH 1 - SH 12 - Show modes 0 - 12 For Show Mode utes. Press any button to turn on the LED display again.
to run properly make sure Sound Active Mode is off. 3. Press ENTER to confirm and exit.
1. Tap the MENU button until “ShNd” is displayed, press
ENTER.
DISP - This function will reverse the display 180º.
2. “Sh X” will now be displayed, “X” representing a number 1. Tap the either the MENU button until “DISP” is displayed,
between 1-12. Programs 1-12 are preset shows, while “Sh 0” press ENTER.
is random mode. Press the UP or DOWN buttons to find your
2. Press the UP button to select “DISP” to activate this function,
desired show and press ENTER to confirm.
or “DSIP” to deactivate this function.

American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 9 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 10
Revo 4 System Menu Revo 4 Operation

3. Press ENTER to confirm. Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller. A DMX controller allows you to create
unique programs tailored to your individual needs.
TEST - This function will run a self test program. 1. The Revo 4 has 4 DMX channel mode and a 256 DMX channel
mode. To set the channel mode see page 8. See page 14 a for
1. Tap the MENU button until “TEST” is displayed, press ENTER.
detailed description of the DMX traits.
2. The fixture will now run a self test. 2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are
included with your DMX controller.
FHRS - With this function you can display the running time 3. Use the controller’s faders to control the various DMX fixture traits.
of the unit. 4. This will allow you to create your own programs.
1. Tap the either the MENU button until “FHRS” is displayed, 5. Follow the instruction on page 8 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
press ENTER.
the last fixture.
2. The display shows the running time of the unit. Press MENU 7. For help operating in DMX mode consult the manual included
to exit. with your DMX controller.
Master-Slave Operation: This function will allow you to link up to
VER - Use this function to display the Software version of 16 units together and operate without a controller. In Master-Slave
the unit. operation one unit will act as the controlling unit and the others will
react to the controlling units programs. Any unit can act as a Master
1. Tap the either the MENU button until “VER” is displayed, or as a Slave.
press ENTER. 1. Using standard XLR microphone cables, daisy chain your units
together via the XLR connector on the rear of the units. Remem-
2. The display will show the software version. ber the Male XLR connector is the input and the Female XLR
connector is the output. The first unit in the chain (master) will use
the female XLR connector only - The last unit in the chain will use
the male XLR connector only. For longer cable runs we suggest a
terminator at the last fixture.
2. On the Master unit find your desired show or choose sound act-
tive mode and set that by pressiing the ENTER button.
3. On the slave units tap the MENU button until “SLND” is display-
ed, and Press ENTER.
4. The slave units will now follow the Master unit.
5. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.

Sound Active Mode: This mode allows a single unit or several units
American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 11 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 12
Revo 4 Operation Revo 4 Traits & Values - 4 Channel DMX Mode
linked together, to run to the beat of the music.
1. Tap the MENU button until “SOUN” is displayed, and press
ENTER.
2. Tap the UP or DOWN buttons until “ON” is displayed and press
ENTER.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.

Show Mode: This mode allows a single unit or several units linked
together, to run 1 of 12 light shows. For Show Mode to run properly
make sure that Sound Active Mode is off.
1. Tap the MENU button until “SHND” is displayed, and press
ENTER.
2. Tap the UP or DOWN buttons until you find your desired show,
and press ENTER to confirm.
Using 4 Channel DMX Mode:
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. To project a pattern using Channel 2, the Channel values must
be between 10-99. This also applies to changing the pattern
color using Channel 3.
Revo 4 Power Cord Daisy Chain To run the chases using Channel 2, the Channel 1 values must
be between 100-239. This also applies to controlling the chase
With this feature you can connect the fixtures to one another
speed using Channel 3.
using the IEC input and output sockets. The quantity that can be
connected is 20 fixtures maximum. After 20 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO Revo 4 Traits & Values - 256 Channel DMX Mode
NOT mix fixtures.

Revo 4 UC3 Control

Blackout Blackout the unit

1. Sound White Strobe Select Show

Function
2. Sound Color Strobe (Show 1-12)

Sound/Strobe Show
Mode
(LED OFF) (LED ON)

American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 13 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 14
 Revo 4 Fuse Replacement Revo 4 Warranty
MANUFACTURER’S LIMITED WARRANTY
First unplug the power. The fuse holder is located next to the power A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
cord. Using a flat-head screw driver unscrew the fuse holder. Remove Audio products to be free of manufacturing defects in material and workmanship for a prescribed
the bad fuse and replace with a new one. period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by ac-
Revo 4 Cleaning ceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
internal and external optical lenses and mirror should be carried out the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
periodically to optimize light output. Cleaning frequency depends on American DJ, Inc. will pay return shipping charges only to a designated point within the United
the environment in which the fixture operates (I.e. smoke, fog residue, States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
dust, dew). In heavy club use we recommend cleaning on a monthly Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
basis. Periodic cleaning will ensure longevity, and crisp output. safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
1. Use normal glass cleaner and a soft cloth to wipe down the out- modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
side casing. of the product; if the product has been repaired or serviced by anyone other than the American DJ,
2. Use a brush to wipe down the cooling vents and fan grill. Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
3. Clean the external optics and mirror with glass cleaner and a soft D. This is not a service contract, and this warranty does not include maintenance, cleaning
cloth every 20 days. or periodic check-up. During the period specified above, American DJ, Inc. will replace defec-
4. Clean the internal optics with glass cleaner and a soft cloth every tive parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
30-60 days. of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replace-
5. Always be sure to dry all parts completely before plugging the unit ment thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
back in.
E. American DJ, Inc. reserves the right to make changes in design and/or improvements
Revo 4 Trouble Shooting upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
Trouble Shooting: Listed below are a few common problems that law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
you may encounter, with solutions. above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
No light output from the unit; sole remedy shall be such repair or replacement as is expressly provided above; and under no
1. Be sure the external fuse has not blown. The fuse is located on circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product.
the rear panel of the unit. This warranty is the only written warranty applicable to American DJ and American Audio
2. Be sure the fuse holder is completely and properly seated. Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
Unit does not respond to sound; MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampli-
1. Low frequencies (bass) should cause the unit to react to sound. fiers)
Tapping on the microphone, quiet or high pitched sounds may • All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
not activate the unit. • American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 15 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 16
Revo 4 Notes Revo 4 Notes

American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 17 American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 18
Revo 4 Specifications

Model: Revo 4
Voltage: 100V~240V 60Hz/50Hz
LEDs: 256 LEDs (64 Red, 64 Green,
64 Blue, and 64 White)
Power Consumption: 29W
Beam Angle: 50 Degrees
Fuse: 7A
Power Cord Daisy Chain: 20 Fixtures Max.
Dimensions: 12.25”(L) x 12”(W) x 13.25”(H)
312mm x 306mm x 334mm
Weight: 10 Lbs. / 4.2 kgs.
Colors: RGB + White
Duty Cycle: None
DMX: 4 or 256 DMX Channels
Sound Active: Yes
Working Position: Any Safe, Secure Position
Warranty: 3 Year (1095 days)

Auto Sensing Voltage: This fixture contains a electronic bal-

last, which will auto sense the voltage when it is plugged into the
power source.

Please Note: Specifications and improvements in the design

of this unit and this manual are subject to change without any
prior written notice. ©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: [email protected]

American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
American DJ® - www.americandj.com - Revo 4 Instruction Manual Page 19 Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99