Em132-133 0

EM13x Series
SMART MULTIFUNCTION METER
Installation and Operation Manual
BG0491 REV. A14

LIMITED WARRANTY
The manufacturer offers the customer a 24-month functional warranty on
the instrument for faulty workmanship or parts from date of dispatch from
the distributor. In all cases, this warranty is valid for 36 months from the
date of production. This warranty is on a return to factory basis.
The manufacturer does not accept liability for any damage caused by
instrument malfunction. The manufacturer accepts no responsibility for
the suitability of the instrument to the application for which it was
purchased.
Failure to install, set up or operate the instrument according to the
instructions herein will void the warranty.
Only a duly authorized representative of the manufacturer may open your
instrument. The unit should only be opened in a fully anti-static
environment. Failure to do so may damage the electronic components and
will void the warranty.
The greatest care has been taken to manufacture and calibrate your
instrument. However, these instructions do not cover all possible
contingencies that may arise during installation, operation or
maintenance, and all details and variations of this equipment are not
covered by these instructions.
If the equipment is used in a manner not specified by SATEC LTD, the
protection provided by the equipment may be impaired.
For additional information regarding installation, operation or maintenance
of this instrument, contact the manufacturer or your local representative
or distributor.
All trademarks are property of their respective owners.

Copyright 2007-2018  SATEC LTD.
2 EM13x Series SMART MULTIFUNCTION METER

WARNING
Read the instructions in this manual before performing installation and take note of the
following precautions:
1. Ensure that all incoming AC power and other power sources are turned OFF before performing
any work on the instrument. Protect the measurement AC Inputs voltage (V1, V2, V3) with 2A
external overcurrent protection device and the power supply source inputs with 5A external
overcurrent protection device, located close to the equipment.
2. Before connecting the instrument to the power source, check the labels on the back of the
instrument to ensure that your instrument is equipped with the appropriate power supply
voltage, input voltages and currents. Failure to do so may result in serious or even fatal injury
and/or equipment damage.
3. Under no circumstances should the instrument be connected to a power source if it is damaged.
4. To prevent potential fire or shock hazard, do not expose the instrument to rain or moisture.
5. The secondary of an external current transformer must never be allowed to be open circuit
when the primary is energized. An open circuit can cause high voltages, possibly resulting in
equipment damage, fire and even serious or fatal injury. Ensure that the current transformer
wiring is secured using an external strain relief to reduce mechanical strain on the screw
terminals, if necessary.
6. Only qualified personnel familiar with the instrument and its associated electrical equipment
must perform setup procedures.
7. Do not open the instrument under any circumstances when it is connected to a power source.
8. Do not use the instrument for primary protection functions where failure of the device can cause
fire, injury or death. The instrument can only be used for secondary protection if needed.
Read this manual thoroughly before connecting the device to the current carrying
circuits. During operation of the device, hazardous voltages are present on input
terminals. Failure to observe precautions can result in serious or even fatal injury or
damage to equipment.
This equipment does not require cleaning for proper operation
EM13x Series SMART MULTIFUNCTION METER 3

Quick Start Guide
This section can be used by a licensed electrician to install and perform
basic EM13X setup. For more detailed EM13X Series setup and use
instructions, see the following chapters in this manual.
This quick start guide will assist you to have the unit running for the first
time.
During the operation of the meter, hazardous voltages are present in the
input terminals. Failure to observe precautions can result in serious or
even fatal injury or damage to equipment.
For complete and accurate in-depth instructions, refer to the following
chapters in this manual.
Installing the EM13X SERIES

Mounting the EM13X SERIES Unit
To mount the EM13X SERIES on Din rail:
 Hang the EM13X Series unit on the DIN Rail by positioning the upper side
first then lower side.
 Push up the DIN rail brackets to lock the EM13X Series on the rail.
Mounting the EM13X Series on DIN-Rail

To mount the EM13X Series on flat surface:
 Locate the EM13X Series on the surface to
 Push up the DIN rail brackets to lock the EM13X Series on the rail.
Connecting the EM13X Series Unit

 Ensure that all incoming power sources are OFF.
 Check that you have the appropriate power supply.
 For direct connection, connect to CT wires through the meter CT
terminals. Observe the arrow that indicates the current direction.
 In case of a retrofit application or high current external SATEC CT (or
Split Core) where each external CT ends with two wires:
 Connect the wire to the meter current termination
screws.
 Connect the measured voltage inputs
 Connect COM1 – RS-485 communication port
 In case of EM132/133 model with Aux. Power supply connect the Power
Supply inputs using 1.5 mm2/14AWG-dedicated wires.
Common Wiring Mode: EM13x and EM13x-SE 4LL3 or 4Ln3

EM13x-SE: Self Energized Meter model

CT wiring
To connect an Option module:

 Assemble the module on the meter.
 Power the EM13X Series unit on.
Assembly a small module

Assembling the 12DI/4RO module
To operate the EM13X Series:

 Perform device diagnostics.
 Configure the device through the EM13X Series unit front panel display
Configuring the EM13X Series remotely

 Install the PAS application software on your PC.
 Configure the PAS database for your meter.
 Configure the PAS communications settings.
 Upgrade the meter firmware if a new version is available.
 Set up the meter using the PAS application software.
 Configure your security settings through the meter security setup.
 Configure your communication protocol settings.
 Configure Billing/TOU registers.
At this stage, the EM13X Series should be ready for operation.

‎Chapter 1 General Information Features
Table of Contents
Chapter 1 General Information ..........................................................................11
1.1 Features.......................................................................................................................13
1.2 Available Options .......................................................................................................14
Digital I/O ............................................................................................................ 15
Analog Output ...................................................................................................... 15
Additional Communication Port– COM2 ................................................................... 15
1.3 Customized Options ..................................................................................................16
Device Resolution.................................................................................................. 16
Display Options..................................................................................................... 16
1.4 Measured Parameters ..............................................................................................16
1.5 Labelling ......................................................................................................................18
Chapter 2 Installation ..........................................................................................19
2.1 Site Requirements .....................................................................................................19
2.2 Package Contents......................................................................................................19
2.3 Mechanical Installation.............................................................................................19
Wall Mounting....................................................................................................... 21
DIN Rail Mounting ................................................................................................. 22
Add-On Module Mounting....................................................................................... 23
2.4 Electrical Installation.................................................................................................23
Connecting the wires ............................................................................................. 24
Typical Installation ................................................................................................ 25
Terminals ............................................................................................................. 30
Power Source Connection....................................................................................... 31
Voltage Input connection ....................................................................................... 33
Current Input Connection....................................................................................... 34
Wiring Diagrams ................................................................................................... 35
2.5 Battery Replacement ................................................................................................42
2.6 I/O Connections ........................................................................................................43
2DI/1RO Standard ................................................................................................ 43
4DI/2RO Module ................................................................................................... 44
8 DI module ......................................................................................................... 45
12DI/4RO Module ................................................................................................. 45
4AO Module - Analog Outputs................................................................................. 46
2G/3G+2 AI Module – 2 x Analog Inputs ................................................................. 48
2.7 Communications Connections.................................................................................49
RS-485 Connection ............................................................................................... 50
ETH module – COM2 Ethernet Connection................................................................ 51
PRO module – COM2 PROFIBUS Connection............................................................. 53
CANopen module – COM2 CANopen Connection ....................................................... 53
RS-232/422-485 module – COM2 Connection .......................................................... 54
Connecting a Cellular module ................................................................................. 55
Connecting an RF module ...................................................................................... 57
Connecting a WiFi module ...................................................................................... 57
Chapter 3 Using Front Display ............................................................................58
Energy Pulse LED .................................................................................................. 58
COMPort Activity LEDs ........................................................................................... 58
VOLTAGES LEDs ................................................................................................... 58
Navigation Buttons ................................................................................................ 58

3.1 Display Operations ....................................................................................................59

Navigating in Data Display Mode............................................................................. 60
Display Features ................................................................................................... 60
Measurement Units ............................................................................................... 61
3.2 Data Displays..............................................................................................................61
TEST Mode Data Display ........................................................................................ 61
Billing Period Energy Data Displays ......................................................................... 61
TOU/Maximum Demand Power Data Display ............................................................ 63
Instrumentation Measurement Maximum Demand Data Display ................................. 65
Instrumentation Measurement................................................................................ 66
Status Inputs and Outputs ..................................................................................... 68
Device Info Display ............................................................................................... 69
3.3 Programming Mode ..................................................................................................71
Entering Numeric Values ........................................................................................ 71
Password Security ................................................................................................. 71
Setup Menus and Access Rights .............................................................................. 71
Viewing and Changing Setup Options ...................................................................... 73
Chapter 4 Using PAS Software ...........................................................................74
4.1 Installing PAS .............................................................................................................74
4.2 Creating a New Site for your Meter ........................................................................74
Chapter 5 Configuring the EM13X Series ..........................................................76
5.1 Configuring Communications..................................................................................76
Setting Up Serial Communication Ports.................................................................... 76
Setting up the Ethernet.......................................................................................... 78
Setting up GPRS Network ...................................................................................... 79
Setting Up WiFi Network ........................................................................................ 80
Setting Up eXpertPower Client ................................................................................ 85
Setting Up TCP Notification Client ............................................................................ 86
5.2 General Meter Setup .................................................................................................87
Basic Meter Setup ................................................................................................. 87
Device Options ..................................................................................................... 91
Configuring Digital Inputs....................................................................................... 92
Configuring Relay Outputs...................................................................................... 94
Configuring Analog Outputs.................................................................................... 97
Configuring Counters ............................................................................................. 99
Configuring Alarm/Control Setpoints...................................................................... 101
Configuring the Display ........................................................................................ 104
Local Time Settings ............................................................................................. 106
5.3 Configuring Meter Security ................................................................................... 108
5.4 Configuring Billing/TOU ........................................................................................ 110
Configuring Billing/Tariff Registers......................................................................... 110
Configuring the Daily Tariff Schedule ..................................................................... 112
Configuring the Season Tariff Schedule.................................................................. 113
5.5 Configuring Recorders ........................................................................................... 114
Configuring Meter Memory ................................................................................... 114
Configuring the Event Recorder ............................................................................ 116
Configuring the Data Recorder .............................................................................. 116
5.6 Configuring Communication Protocols............................................................... 119
Configuring Modbus............................................................................................. 119
Configuring DNP3................................................................................................ 120

Chapter 6 Device Control and Upgrading....................................................... 123

6.1 Resetting Accumulators, Maximum Values and Files ...................................... 123
6.2 Updating the Meter Clock...................................................................................... 125
6.3 Viewing and Clearing Device Diagnostics .......................................................... 126
6.4 Viewing Communication Status and Statistics.................................................. 126
6.5 Remote Relay Control ............................................................................................ 127
6.6 Upgrading Device Firmware................................................................................. 128
Chapter 7 Monitoring Meters ........................................................................... 130
7.1 Viewing Real-time Data......................................................................................... 130
7.2 Viewing Real-time Min/Max Log ......................................................................... 133
7.3 Viewing Real-time Waveforms ............................................................................ 133
7.4 Viewing Real-time Harmonic Spectrum............................................................. 135
Chapter 8 Retrieving and Storing Files........................................................... 139
8.1 Uploading Files on Demand.................................................................................. 139
8.2 Using the Upload Scheduler.................................................................................. 140
8.3 Viewing Files On-line.............................................................................................. 142
8.4 Exporting Files......................................................................................................... 142
Exporting Files in COMTRADE and PQDIF Formats................................................... 142
Exporting Files in Excel Format ............................................................................. 143
8.5 Archiving Files ......................................................................................................... 144
Chapter 9 Viewing Files .................................................................................... 145
9.1 Operations with Files ............................................................................................. 145
9.2 Viewing Options...................................................................................................... 145
Customizing Views .............................................................................................. 145
Working with Tables ............................................................................................ 146
Working with Graphic Windows............................................................................. 146
9.3 Viewing the Event Log ........................................................................................... 148
9.4 Viewing the Data Log............................................................................................. 149
Appendix A Technical Specifications .............................................................. 151
Appendix B Standards Compliance................................................................. 157
Appendix C Analog Output Parameters ......................................................... 160
Appendix D Setpoint Triggers and Actions .................................................... 162
Appendix E Parameters for Data Monitoring and Logging.......................... 165
Appendix F Billing/TOU Profile Log File ......................................................... 174
Appendix G Data Scales.................................................................................... 176
Appendix H Device Diagnostic Codes ............................................................. 177

Chapter 1 General Information
The EM13X Series is a compact, multi-function, three-phase AC

Powermeter specially designed to meet the requirements of users
ranging from electrical panel builders to substation operators.
The EM13X Series measuring and power supply inputs comply with Measuring

Category III
The EM13X Series offers standard voltage, current, power and

frequency measurements, amp-demand, energy measurements and
data logging, harmonic analysis and control capabilities.
The EM13X Series consists of three different models series:

 EM132/EM133 with AC/DC Auxiliary Power Supply (40-318V AC/DC)
‒ EM132/EM133-5, internal CT, transformer operated

configuration with current inputs: In = 5A, Imax = 10A
‒ EM132/EM133-1, internal CT, transformer operated
‒ EM132/EM133-RS5, external CT, transformer operated
configuration with current inputs (secondary current): In =
2.mA, Imax = 5mA
‒ EM132/EM133-50, internal CT, direct connection configuration
with current inputs: In = 50A, Imax = 63A1
‒ EM132/EM133-HACS, external CT, direct connection
20mA, Imax = 40mA
 EM133-SE – self energized device with 3 Phase Power Supply,
operating from any combination of the measured phases
‒ EM133-SE-5, internal CT, transformer operated configuration

with current inputs: In = 5A, Imax = 10A
‒ EM133-SE-1, internal CT, transformer operated configuration
with current inputs: In = 1A, Imax = 2A
‒ EM133-SE-RS5, external CT, transformer operated configuration
with current inputs (secondary current): In = 2.mA, Imax =
5mA
1
Imax= 63A at 60°C max. amb. temperature, Imax=100A at 55°C max. amb. temperature

‒ EM133-SE-50, internal CT, direct connection configuration with

current inputs: In = 50A, Imax = 63A1
‒ EM133-SE-HACS, external CT, direct connection configuration
with current inputs (secondary current): In = 20mA, Imax =
40mA
 EM132/EM133-21DC with DC Auxiliary Power Supply (9-36 VDC)
‒ EM132/EM133-21DC-5, internal CT, transformer operated

‒ EM132/EM133-21DC-1, internal CT, transformer operated
‒ EM132/EM133-21DC-RS5, external CT, transformer operated
2.mA, Imax = 5mA
‒ EM132/EM133-21DC-50, internal CT, direct connection
configuration with current inputs: In = 50A, Imax = 63A1
‒ EM132/EM133-21DC-HACS, external CT, direct connection
20mA, Imax = 40mA
All models series include the following units:
 2 lines of 16 characters LCD display.
 A standard RS-485 communication port, Infra-Red Communication

port and an additional optional Ethernet, Profibus or RS-232/RS-
422/RS-485 or RF Modem port. These ports allow local and remote
automatic meter readings and setup through the supplemental
communication or user data acquisition software
 Different communication options for remote communications with the

meter. These options enable LAN and Internet communication with
the unit.
 Two digital inputs with 10-ms scan time and one relay output with 1-
cycle update time
The EM13X Series is suitable for mounting on both standard DIN-Rail

and wall-mount.
The EM13X firmware Series consists of various firmware

implementations and resources as described in following table:
Communication protocols App. Storage CPU

memory memory
Versions MODBUS/ ASCII SATEC DNP Profibus CAN WiFi 60870 AR 8 MB 512 kB
RTU
V12.02.xx V ─ ─ V V V V ─ ─ ─ ─
V12.05.xx V ─ ─ ─ V V V ─ V ─ ─
V12.06.xx V ─ V ─ V ─ ─ ─ ─ ─ ─
V12.07.xx V ─ ─ ─ V V V ─ V V ─
V12.08.xx V ─ ─ V V V V ─ ─ ─ V
V12.22.xx V ─ ─ ─ V ─ V V ─ ─ ─
V12.28.xx V ─ ─ ─ V ─ V V ─ ─ V
1

1.1 Features
Multifunctional 3-phase Power Meter
 3 voltage inputs and 3 current transformer-isolated AC inputs for
direct connection to power line or via potential and current
transformers
 True RMS, volts, amps, power, power factor, neutral current, voltage
and current unbalance, frequency
 Ampere/Volt demand meter
 25/50/60/4001 Hz measurement capabilities
Billing/TOU Energy Meter

 IEC 62053-22 Class 0.5S /ANSI C12.20 Acc. Class 0.5, four-quadrant
active and reactive energy polyphase static meter
 Three-phase total and per phase energy measurements; active,

reactive and apparent energy counters
 Time-of-Use, 4 totalization and tariff energy/demand registers x 8

tariffs, 4 seasons x 4 types of days, 8 tariff changes per day,
 One–time easy programmable tariff calendar schedule
 Automatic daily energy and maximum demand profile log for total
and tariff registers
 Voltage and current THD, current TDD and K-Factor, up to 40th

order harmonic
 Voltage and current harmonic spectrum and angles
Real-time Waveform Capture

 Real-time “scope mode” waveform monitoring capability
 Simultaneous 6-channel one-cycle waveform capture at a rate of 64

samples per cycle
Programmable Logical Controller

 Embedded programmable controller
 16 control setpoints; programmable thresholds and delays
 Relay output control
 1-cycle response time
 Non-volatile memory for long-term event and data recording
 Event recorder for logging internal diagnostic events and setup

changes
 Two data recorders; programmable data logs on a periodic basis;

automatic daily energy and maximum demand profile log
Digital I/O
 2 digital inputs (standard) and four to twelve digital inputs (optional)
with 1/2 cycle scan time; automatic recording of last five digital input
1
25Hz and 400Hz options are available only with internal CT.

‎Chapter 1 General Information Available Options
change events with timestamps (see the EM13X Series MODBUS

Reference Guide)
 1 relay output (standard) and two to four relay outputs (optional)

with 1-cycle update time; unlatched, latched, pulse and KYZ
operation; energy pulses
Display
 Easy to read 2x16 characters LCD display, adjustable update time
 Auto-scroll option with adjustable page exposition time; auto-return

to a default page
 Programmable display auto-scroll sequence
Communications
 Standard 2-wire RS-485 communication port; MODBUS RTU, DNP3,
SATEC ASCII and IEC 60870-5-101 communication protocols
 Optional second communication port; MODBUS RTU, MODBUS/TCP,

DNP3, DNP3/TCP, SATEC ASCII, PROFIBUS DP, CANopen and IEC
60870-5-104 (over TCP) communication protocols
 eXpertPower client for communicating with the SATEC proprietary

eXpertPower Internet services (with the Ethernet/GPRS module)
 TCP notification client for communicating with a remote

MODBUS/TCP server on events or periodically on a time basis (with
the Ethernet/GPRS module)
Meter Security
 Password security for protecting meter setups and accumulated data
from unauthorized changes
Upgradeable Firmware
 Easy upgrading device firmware through a serial or Ethernet port.
Software Support
 PAS™ – meter configuration and data acquisition SATEC Software
tool
 eXpertPower™ – SATEC proprietary Internet services
1.2 Available Options

The EM13X Series can be provided with an optional expansion module
from the following list:
 Digital I/O
 Analog outputs
 Ethernet communication port
 PROFIBUS DP communication port
 CANopen communication port
 RS-232/RS-422/RS-485 communication port
 Cellular communication port based on ENFORA GPRS or TELIT 3G or

4G engine
 RF communication port

‎Chapter 1 General Information Available Options
 WiFi module, wireless Ethernet communication port
Digital I/O
The EM13X Series digital I/O expansion module provides:
4DI/2RO Module
 4dry contact digital inputs (DI) for monitoring external contacts and
receiving pulses from energy, water, and gas meters; Programmable
de-bounce time; 1-ms scan time.
 2 electro-mechanical or solid-state relay outputs (RO) for alarms and

controls, and for output energy pulses; unlatched, latched and pulse
operations, failsafe operation for alarm notifications; programmable
pulse width; direct remote relay control through communications; 1-
cycle update time.
8DI module
 8 dry contact digital inputs (DI) for monitoring external contacts and
receiving pulses from energy, water, and gas meters
 Programmable de-bounce time; 1-ms scan time.
12DI/4RO Module
 12 dry contact digital inputs (DI) for monitoring external contacts
and receiving pulses from energy, water, and gas meters;
Programmable de-bounce time; 1-ms scan time.
 4 electro-mechanical relay outputs (RO) for alarms and controls, and

for output energy pulses; unlatched, latched and pulse operations,
failsafe operation for alarm notifications; programmable pulse width;
direct remote relay control through communications; 1-cycle update
time.
Analog Output
The EM13X Series analog output (AO) expansion module provides:
 4 optically isolated analog outputs with an internal power supply;
 Options for 0-20mA, 4-20mA, 0-1mA, and  1mA output; 1-cycle

update time.
Additional Communication Port– COM2

A second COM2 communication port can be ordered as an expansion
module. COM2 options available:
 Ethernet 10/100BaseT port; MODBUS/TCP, DNP3/TCP or IEC 60870-
5-104 communications protocols
 WiFi module, wireless Ethernet communication port
 PROFIBUS DP port
 CANopen port
 RS-232/RS-422/RS-485 port; MODBUS RTU, DNP3 or IEC 60870-5-

101, and SATEC ASCII communication protocols;
 GPRS or 3G/4G cellular communications port; MODBUS/TCP protocol
 RF communication; MODBUS RTU protocol

‎Chapter 1 General Information Customized Options
1.3 Customized Options

Presentation of data on the front display and via communications can
be customized to best suit the user application.
Device Resolution
A low or high-resolution option can be selected for the presentation of
voltage, current, and power for use in high and low power applications.
Display Options
Different display options are available for customization to be used in
dark or non-safe locations, or in places that are hardly accessible for
observation.
1.4 Measured Parameters

Table 1: Measured and Displayed Parameters
Parameter Display Comm. Analog Pulse Alarm
1-cycle Real-time Measurements
RMS Voltage per phase   
RMS Current per phase   
kW per phase  
kvar per phase  
kVA per phase  
Power Factor per phase  
Total kW   
Total kvar   
Total kVA   
Frequency   
Neutral Current   
Total Power Factor   
Voltage & Current unbalance  
1-sec Average Measurements

RMS Voltage per phase    
RMS Current per phase    
kW per phase   
kvar per phase   
kVA per phase   
Power Factor per phase   
Total kW    
Total kvar    
Total kVA    
Total Power Factor    
Frequency    
Neutral Current    
Voltage & Current unbalance   
Amps & Volt Demands
Ampere & Volt Demand per phase  
Ampere Maximum Demand per phase   
Voltage Maximum Demand per phase   
Power Demands
kW Accumulated Demand Import & Export   

‎Chapter 1 General Information Measured Parameters

kvar Accumulated Demand Import & Export   
kVA Accumulated Demand   
kW Demand Import & Export  
kvar Demand Import & Export  
kVA Demand  
kW Sliding Demand Import & Export  
kvar Sliding Demand Import & Export  
kVA Sliding Demand  
kW Predicted Demand Import & Export  
kvar Predicted Demand Import & Export  
kVA Predicted Demand  
kW Maximum Demand Import  
kW Maximum Demand Export  
kvar Maximum Demand Import  
kvar Maximum Demand Export 
kVA Maximum Demand  
Total Energy
Total kWh Import & Export   
Total kvarh Import & Export   
Total kvarh Net 
Total kVAh   
Energy per Phase
kWh Import per phase  
kvarh Import per phase 
kVAh per phase  
TOU Registers
4 TOU energy registers (kWh and kvarh  
import & export, kVAh, 4 pulse sources)
4 TOU maximum demand registers 
8 tariffs, 4 seasons x 4 types of day   
Harmonic MeasurementsEH
Voltage THD per phase    
Current THD per phase    
Current TDD per phase    
K-factor per phase    
Voltage harmonics per phase up to order 40 
Current harmonics per phase up to order 40 
Voltage harmonic angles up to order 40 
Current harmonic angles up to order 40 
Fundamental Component
Voltage and Current per phase  
kW, PF per phase  
kvar, KVA per phase  
Total kW, PF  
Total kvar, KVA  
Min/Max Logging
Min/Max A, V, total kW, kvar, kVA, PF  
Min/Max Frequency, Neutral current  
Phase Rotation   
Voltage and Current Phase Angles  
Day and Time  

‎Chapter 1 General Information Labelling

Pulse Counters   
Digital Inputs (optional)   
Relay Outputs (optional)   
Remote Relay Control (optional) 
Alarm Triggers/Setpoints  
Self-diagnostics  
1.5 Labelling
Figure ‎1-1 EM133 label – UL marking
Figure ‎1-2 EM133 label – NMI marking
Figure ‎1-3 EM133 label – CE MID marking

‎Chapter 2 Installation Site Requirements
Chapter 2 Installation
This chapter discusses the following types of physical installations for
the EM13X Series SMART MULTIFUNCTION METER:
 Mechanical Installation
 Electrical Installation
 I/O Connections
 COM Port Connections.
2.1 Site Requirements

 Environmental conditions: as specified in Technical Specifications in
Appendix A
 Electrical requirements: as specified in Technical Specifications in

Appendix A
See Technical Specifications in Appendix A for more details
2.2 Package Contents

The EM13X Series SMART MULTIFUNCTION METER package contains
the following items:
 EM13X Series SMART MULTIFUNCTION METER unit
 Technical Documentation CD
 EM13X Series Quick Start guide
2.3 Mechanical Installation

Refer to the figures provided in this section to properly perform the
mechanical installation.

‎Chapter 2 Installation Mechanical Installation
Figure ‎2-1 Dimensions

Wall Mounting
To mount the meter on the wall:
Position the meter on the wall according to hole locations as shown in
figure 2-2
Affix the meter using washers and nuts.
Figure ‎2-2. Surface Mounting

DIN Rail Mounting

The EM13X Series can be mounted on a standard 35-mm DIN rail as
shown in figure 2-3
Figure ‎2-3. EM13X Series DIN Rail Mounting

‎Chapter 2 Installation Electrical Installation
Add-On Module Mounting

Before Add-On Module installation ensure that all incoming power
sources are shut OFF. Failure to observe this practice can result in
serious or even fatal injury and damage to equipment.
Turn off the EM13X Series auxiliary power supply or voltage supply
inputs (SE model).
Remove the module connector cover from the EM13X Series to access
the module connector as shown in figure 2-4below
Figure ‎2-4. EM13X Series module connector location
Figure ‎2-5. EM13X Series module assembly
2.4 Electrical Installation

The equipment installation shall conform to the following instructions:

a) a switch or circuit-breaker shall be included in the building
installation as close as possible to the equipment supply voltage;
b) It shall be in close proximity to the equipment and within easy reach
of the OPERATOR;
c) It shall be marked as the disconnecting device for the equipment.
d) Before installing, ensure that all incoming power sources are shut
OFF. Failure to observe this practice can result in serious or even fatal
injury and damage to equipment.
e) The current sensors may not be installed in a panel where they
exceed 75% of the wiring space of any cross-sectional area within the
panel.
Connecting the wires

All conductors must be stranded copper. All conductors and insulation
systems and crimped devices must be appropriate for the application.
SATEC requires using crimped ferrules on stranded wire.
Table 3 below summarizes the different conductors’ sizes to be used in

the EM133 external connections.
Table 2: Wiring Characteristics
Conductor size
Torque
Terminals EM133 model Minimum Maximum Notes
[Nm]
AWG (mm²) AWG (mm²)
Aux. Power N/A in EM133- 22 (0.5) 12 (4.0) 0.5-0.7 Use 600V insulated conductors
Supply Inputs SE models Required crimped ferrule:
L/+, N/- Panduit (22AWG) F75-10-M
Panduit (12AWG) F81-15-M
Voltages Inputs N/A in EM133- 22 (0.5) 12 (4.0) 0.5-0.7 Use 600V insulated conductors
V1, V2, V3, Vn SE-100A Required crimped ferrule:
Current Inputs EM133/SE- 22 (0.5) 10 (6.0) 1.8-2 Use 600V insulated conductors
I1, I2, I3, N 1A, 5A, HACS Required crimped ferrule:
Current Inputs EM133/SE- 6 (16) 4 (25) 2-2.7 Use 600V insulated conductors
I1, I2, I3, N 63A or 100A Required crimped ferrule:
COM1, I/O All Models 22 (0.5) 12 (4.0) 0.5-0.7 Use 600V insulated conductors
connections Required crimped ferrule:

Typical Installation
Figure ‎2-6a Typical Installation Diagram with Auxiliary Power Supply

*
1. SATEC RF chokes to be installed between CBR and Meter
Voltage Inputs in residential area or other places require ANCI
C12.20 compliance. Otherwise it may be bypassed.
2. AC0242 shall be routed with the voltage lines (bundled),
separately from communication & I/O lines
Figure ‎2-6b Typical Installation Diagram with Self Energized Power Supply – direct connection with HACS

Figure ‎2-6c Typical Installation Diagram with Self Energized Power Supply – direct connection

*
1. SATEC RF chokes to be installed between CBR and Meter
Voltage Inputs in residential area or other places require ANCI
C12.20 compliance. Otherwise it may be bypassed.
2. AC0242 shall be routed with the voltage lines (bundled),
separately from communication & I/O lines
Figure ‎2-6d Typical Installation Diagram with Self Energized Power Supply – Transformer Operated
(indirect connection)

Figure ‎2-6e Typical Installation Diagram with 12/24 VDC Auxiliary Power Supply

Terminals
The EM132/133/133-SE terminals are constructed as a built-in part of
the meter equipment. The terminals are divided in two different
terminal categories:
1) High power terminal, dedicated to current terminals only, with a

torque rating of 2.0-2.3Nm
2) Low power terminal, dedicated to voltage, Digital Inputs, COM1

and Relay output terminals only with a torque rating of 0.5-0.7Nm
Figure ‎2-7a Terminals View EM133 Model

Figure ‎2-7b Terminals View EM133-SE Model
Power Source Connection

of the OPERATOR;
panel.
The power source can be a dedicated fuse or a monitored voltage if it is

within the instrument power supply range.
To connect an AC Auxiliary Power Supply (EM133 model only):

Connect the Line wire to terminal (L/+ or 9).
Connect the Neutral wire to terminal (N/- or 10)
To connect to a DC Auxiliary Power Supply (EM133 and EM133-21DC models only):
Connect the positive wire to terminal (L/+ or 9)
Connect the negative wire to terminal (N/- or 10)

Figure ‎2-8 EM13X Series Auxiliary Power Supply connection

Voltage Input connection

of the OPERATOR;
panel.
EM13x Series (with Aux. Power Supply) 690V Inputs (Standard)
Figure ‎2-9EM13X Series (with Aux. Power Supply) measured Voltage connections
690V inputs are usually used with direct connection. Use any of the
seven wiring configurations shown in Figures 2-8 through 2-15.
EM13X-SE model Voltage connections
Figure ‎2-10 EM13X-SE model measured Voltage connections
EM133-SE model with measuring nominal current 1A or 5A or 2.5mA

(using RS5), indirect connection – nominal voltage input is 120(207) to
277 (480) VAC.
EM133-SE model with measuring nominal current 50A or 20mA (using

HACS), direct connection – nominal voltage input is up to 230(400)
VAC.

Current Input Connection

The EM13X Series consists of five different models according to the
current inputs measurement:
1A nominal current (2A maximum) using internal CT – transformer
operated Connection
5A nominal current (10A maximum) using internal CT – transformer
operated Connection
50A1 nominal current (63A/100A maximum) using internal CT – Direct
Connection, in EM133-SE model Current Inputs and Voltage Inputs are
internally connected together
20mA nominal current (40mA maximum) using HACS (external CT
provided by SATEC) – Transformer Connection
2.5mA nominal current (5mA maximum) using RS5 (external CT
provided by SATEC) – Transformer Connection
Figure ‎2-11 EM13X Series measured Current connections
1

Wiring Diagrams
For AC input ratings, see Technical Specifications in Appendix A for
more details.
Table 3 presents the available wiring configurations in the meter.
Table 3: Wiring Configurations
Wiring Configuration Setup Code Figure

3-wire 2-element Delta direct connection using 2 CTs 3dir2 2-12
4-wire 3-element Wye direct connection using 3 CTs 4Ln3 or 4LL3 2-13
4-wire 3-element Wye connection using 3 PTs, 3 CTs 4Ln3 or 4LL3 2-14
3-wire 2-element Open Delta connection using 2 PTs, 3OP2 2-15
2 CTs
4-wire 2½-element Wye connection using 2 PTs, 3 3Ln3 or 3LL3 2-16
CTs
3-wire 2½-element Open Delta connection using 2 3OP3 2-17
PTs, 3 CTs
4-wire 3-element Delta direct connection using 3 CTs 4Ln3 or 4LL3 2-18
3-wire 2½-element Broken Delta connection using 2 3bLn3 or 2-19
PTs, 3 CTs 3bLL3

Figure ‎2-12 3-Wire 2-Element Delta Direct Connection Using 2 CTs (Wiring Mode = 3dir2)

Figure ‎2-13 4-Wire Wye 3-Element Direct Connection Using 3 CTs (Wiring Mode = 4LL3 or 4Ln3)

Figure ‎2-14 4-Wire Wye 3-Element Connection Using 3 PTs, 3 CTs (Wiring Mode = 4LL3 or 4Ln3)
Figure ‎2-15a 3-Wire 2-Element Open Delta Connection Using 2 PTs, 2 CTs (Wiring Mode = 3OP2)

Figure ‎2-15b 3-Wire 2-Element Open Delta Connection Using 3 PTs, 2 CTs (Wiring Mode = 3OP2)
This configuration provides accurate power measurements only if the voltages are balanced.
Figure ‎2-16 4-Wire Wye 2½-Element Connection Using 2 PTs, 3 CTs (Wiring Mode = 3LL3 or 3Ln3)

Figure ‎2-17 3-Wire 2½-Element Open Delta Connection Using 2 PTs, 3 CTs (Wiring Mode = 3OP3)
Figure ‎2-18 4-Wire 3-Element Delta Direct Connection Using 3 CTs (Wiring Mode = 4LL3 or 4Ln3)

Figure ‎2-19 3-Wire 2½-Element Broken Delta Connection Using 2 PTs, 3 CTs (Wiring Mode = 3bLn3 or
3bLL3)

‎Chapter 2 Installation Battery Replacement
2.5 Battery Replacement

WARNING!
Only qualified personnel familiar with the instrument and its associated
electrical equipment must perform the RTC battery backup replacement.
The battery replacement must be performed while equipment power
supply is "ON"
To replace the CR2032 RTC battery:

1) Remove the EM13X Series cover
2) Remove the old battery by lifting up the battery holder retractable
tab.
3) Place the new CR2032 battery into the battery holder while holding up
the battery holder retractable tab in such a way that the (+) battery pole
‎ -7.
is toward the battery holder, as shown in Figure 2
Figure ‎2-7 EM13X Series Battery Replacement

‎Chapter 2 Installation I/O Connections
2.6 I/O Connections

Before I/O Module installation ensure that all incoming power sources
are shut OFF. Failure to observe this practice can result in serious or
even fatal injury and damage to equipment.
For I/O ratings, see Technical Specifications in Appendix A.
2DI/1RO Standard
Relay Output
The EM13X Series basic provides one dry contact relay (SSR FORM A)
for energy pulsing, alarms or remote control
Figure ‎2-8 EM13X Series Relay output connection
Digital Inputs
Two optically isolated status inputs are provided for status monitoring,
pulse counting, external power demand period, and time
synchronization.
Figure ‎2-9 EM13X Series Digital Input connections

4DI/2RO Module
Before I/O Module installation ensure that all incoming power sources
are shut OFF. Failure to observe this practice can result in serious or
even fatal injury and damage to equipment.
Figure ‎2-10 4DI/2RO Module Assembly
Relay Outputs
There are two relay outputs provided for energy pulsing, alarms, or
remote control.
Figure ‎2-11 Relay Output Connection
Digital Inputs
Four optically isolated status inputs are provided for status monitoring,
synchronization.
Figure ‎2-12 4 DI/2DO - Digital Input Connection

8 DI module
Eight optically isolated status inputs are provided for status monitoring,
synchronization
Figure ‎2-13 8 DI - Digital Input Connection
12DI/4RO Module
The 12DI/4RO module can be equipped with optional communication
port COM2 – ETHERNET or RS-422/485.
Figure ‎2-14 12DI/4RO Module
Relay Outputs
There are four electro-mechanic relay outputs provided for energy

pulsing, alarms, or remote control.

Figure ‎2-15 Relay Output Connection
Digital Inputs
12 optically isolated status inputs are provided for status monitoring,

synchronization.
Figure ‎2-16 12 Digital Input Connection
4AO Module - Analog Outputs

The 4AO module has four optically isolated analog outputs with an
internal power supply and current output options of 0-20 mA and 4-20
mA (current loop load of up to 500 Ohm), 0-1 mA and ±1 mA (2mA
100% overload, current loop load of up to 5 kOhm).

Figure ‎2-17 4AO Module Assembly
Figure ‎2-18 Analog Output Connection

It is recommended to connect unused Analog output channels to
Common terminal.
The 4AO module TERMINAL is for use only with equipment which has no
live parts which are ACCESSIBLE
The RATING of the insulation of the external equipment for use with the
4AO module, shall comply according to Installation Category III for
insulation to be suitable for SINGLE FAULT CONDITION

The external equipment TERMINAL connection type is normally terminal
block for wire size 14 AWG (up to 1.5 mm2)
The type of equipment that might be connected to the TERMINAL is:
Programmable Logic Controller for automation – PLC
Digital or Analog meter

2G/3G+2 AI Module – 2 x Analog Inputs

The 2G/3G+2AI module has two optically isolated analog inputs with
an internal power supply and current input measurement of 4-20 mA
(current loop load of up to 500 Ohm), that could be interfaced to a 4-
20mA Temperature sensor.

‎Chapter 2 Installation Communications Connections
2.7 Communications Connections
Before installing the Communication Module, ensure that all incoming

power sources are shut OFF. Failure to observe this practice can result
in serious or even fatal injury and damage to equipment.
Several communication options are available for the EM13X Series:

 COM1 (standard): RS-485
 COM2 (optional module):
Ethernet 10/100BaseT
PROFIBUS DP
CANopen
RS-232 or RS-422/485
2G/3G/4G
2G/3G+2AI
RF
 COM3 (standard): IR
A full description of the communication protocols is found in the EM13X

Series protocol guides that come with your meter.

RS-485 Connection
RS-485 COM1
Figure ‎2-19 COM1 RS-485 2-Wire Connection
Communication cable Specification: Shielded, #22AWG.

Note: pay attention to GND connection (SH->GND).

ETH module – COM2 Ethernet Connection

The EM13x ETHERNET module can be used in three different modules
form factors:
- Regular ETHERNET Module that can be used in PM13x & EM13x
- DIN Rail ETHERNET module that can only be used in EM13x.
- Combined with 12DI/4DO module that can be used in PM13x &

EM13x
Figure ‎2-20a Regular Ethernet module
Figure ‎2-21b DIN Rail Ethernet module
Figure ‎2-22c 12DI/4DO Combined Ethernet module

Figure ‎2-23 COM2 Ethernet Connection

The ETH module TERMINAL is for use only with equipment which has no
The RATING of the insulation of the external equipment for use with
the ETH module, shall comply according to Installation Category III for
 insulation to be suitable for SINGLE FAULT CONDITION
The external equipment TERMINAL connection type is RJ-45
Personal Computer – PC or LAPTOP
10/100Base-T LAN HUB and/or Switch

PRO module – COM2 PROFIBUS Connection
Figure ‎2-24 COM2 PROFIBUS Connection
The PRO module TERMINAL is for use only with equipment which has no
The RATING of the insulation of the external equipment for use with the
PRO module, shall comply according to Installation Category III for

insulation to be suitable for SINGLE FAULT CONDITION
The external equipment TERMINAL connection type is DB9
Programmable Logic Controller for automation – PLC
CANopen module – COM2 CANopen Connection

RS-232/422-485 module – COM2 Connection
Figure ‎2-25 COM2 RS-232 connection
Figure ‎2-26 COM2 RS-422/485 connection
The RS-232/422-485 module TERMINALS are for use only with

 equipment which has no live parts which are ACCESSIBLE
The RATING of the insulation of the external equipment for use with The

RS-232/422-485 module, shall comply according to Installation

Category III for insulation to be suitable for SINGLE FAULT CONDITION
The external equipment TERMINAL connection type is normally terminal
block for wire size 14 AWG (up to 1.5 mm²) – RS-422/485 port and
DB9 male-to-female cable more than 22 AWG (0.3mm²)
Personal Computer – PC or LAPTOP
Connecting a Cellular module

The EM13x series can be equipped with 2G/3G/4G module for remote
communication using public cellular network to a remote MODBUS/TCP
server.
It consists of three types of Cellular module:
1) 2G/3G module, mainly for GSM network (Regular or DIN rail form
factor)
2) 2G/3G+2AI module, including 2 x Analog Inputs 4-20mA (DIN Rail

form factor)
3) 4G LTE module for following service providers (Regular or DIN rail

form factor):
- Verizon (US), using Module 4G Verizon LE910-SV V2
- AT&T (US), using Module 4G AT&T LE910-NA V2
- Telstra (AU), using Module 4G Telstra LE910-AU V2
- Europe (EU), using Module 4G Europe LE910-EU V2
The EM13x Cellular module can be used in two different form factors:
- Regular Cellular Module that can be used in PM13x & EM13x
- DIN Rail Cellular module that can only be used in EM13x.
Figure ‎2-27a COM2 2G/3G/4G Regular module Connection

SIM
Cartridge

Figure ‎2-28b COM2 2G/3G+2AI DIN Rail module Connection

SIM
Cartridge
Figure ‎2-29b COM2 2G/3G/4G DIN Rail module Connection
The Cellular SIM must not have any incoming voice call. The customer
must require from the Service Provider for DATA services only
 The Cellular module can be equipped with two different antennas:
internal Antenna for installation into plastic closet or no-metallic
environment. For metallic installation use external antenna
See Setting Up GPRS in Chapter 5 for information on configuring

Cellular communications in your meter.

Connecting an RF module
Figure ‎2-30 COM2 RF module Connection
The RF modem module can be equipped with two different antennas:

 internal Antenna for installation into plastic closet or no-metallic
environment. For metallic installation use external antenna
Connecting a WiFi module

A WiFi module can be connected to the meter COM2 port to provide
communications with the remote MODBUS/TCP server via a WiFi
See Setting Up WiFi Network in Chapter 5 for information on

configuring WiFi communications in your meter.

‎Chapter 3 Using Front Display Communications Connections
Chapter 3 Using Front Display

This chapter provides EM13X Series SMART MULTIFUNCTION METER
front panel information and operating procedures.
Figure ‎3-1: EM13X Series Unit
Energy Pulse LED

The EM13X Series has a red “Energy Pulse” LED. It flashes at a
constant rate when a load is applied to the meter.
There are two modes of LED operation:

 NORMAL mode: the LED pulses indicate imported Wh at a rate of
1,000 pulses per kWh
 TEST mode: the LED pulses indicate either imported Wh, or

imported (inductive) varh at a rate of 10,000 pulses per kWh/kvarh
The energy test mode can be enabled through the Device Options
setup. When in test mode, the energy and demand accumulators do
not account for consumed energy.
COMPort Activity LEDs

The meter has two yellow LEDs “RX” and “TX”, which indicate activity
on the COM1 communication port. The LEDs flash when the port is
receiving or transmitting data.
VOLTAGES LEDs
The meter has three green LEDs “L1, "L2" and "L3”, which indicate
voltage measurement input presence. When LEDs are "ON", that
means that the voltage measurement inputs exist in the meter
Navigation Buttons
The EM13X Series is provided with two push buttons that are normally
used to navigate between different measurement displays.
The "UP" and "DOWN" function of buttons changes depending on what

operating mode the display is in. In programming mode, the buttons
access the device setup menus where the default factory-set device
settings can be changed.

‎Chapter 3 Using Front Display Display Operations
3.1 Display Operations

The EM13X Series has a high-contrast graphical LCD display with
backlight for local data read outs, meter setup and servicing.
The display operates in two modes:

 Multi-page data display mode with Auto-Scroll feature allows you to
scroll through display screens and pages to view various billing,
instrumentation and status data.
 Programming mode allows you to enter menu-driven device setups

for inspecting and changing factory set meter parameters, or
resetting maximum demands, counters and device diagnostics
messages. The display is normally updated once per second except
of the clock display where the update rate changes to twice per
second.
Navigation Buttons
The EM13X Series is provided with two navigation buttons,
SELECT/ENTERbutton and SCROLL button.
You can perform three types of actions with each button:

 Short press, or “press and release”
 Long press, or “press and hold for 1 to 2 seconds”
 Extended press, or ”press and hold for 5 seconds or longer ”
The function of each button changes depending on what operating

mode the display is in.
The SCROLL button operates once it is briefly pressed. It has two

functions:
 In data display mode, it scrolls through the display pages.
 In programming mode, it scrolls through the menu items and allows

changing a selected digit when entering numbers.
The SELECT/ENTER button normally operates once it’s released. The

button function changes depending on the time the button is pressed:
 In data display mode, when pressed briefly and released, it scrolls
through the display views; a long press for more than 5 seconds
switches to programming mode.
 In programming mode, when pressed briefly and released, it moves

from one menu item to another; a long press for one second selects
a highlighted menu item allowing to enter a submenu or to store a
changed item.
In data display mode, when the SCROLL and SELECT/ENTER buttons

are briefly pressed together and then released, the current display
returns to the start page; in some pages, an extended press for more
than 5 seconds is used as a “shortcut” for immediate entering a
specific programming menu.

‎Chapter 3 Using Front Display Display Operations
Navigating in Data Display Mode

The following table gives a summary of the button operations in data
display mode.
Button Press Operations
SCROLL Short press Scroll through pages
SELECT/ENTER Short press Scroll through displays
SELECT/ENTER Long press Enter programmed parameter
SELECT/ENTER Extended press Enter programming mode
The EM13X Series provides 7 different multi-page data displays. See

Data Displays for the full displays list and enumeration.
Display Features
The EM13X Series display has a number of programmable features that
can be disabled, enabled and adjusted via the meter Display Setup
(see Display Setup in Chapter 5).
Backlight
A short press on any button while the display backlight is off switches
the backlight on.
The backlight stays on as long as you selected in the display setup and
then dims to conserve power. The backlight time is factory set to 1
minute and can be programmed from 1 to 10 minutes. You can
temporarily set the backlight to continuous operation if you need to
work in dark for more time.
Auto-Return
If the Auto-Return feature is enabled and no button is pressed for the

programmable Auto-Return interval (1 to 30 minutes for data displays;
fixed at 5 minutes for setup menus), the display automatically returns
to the default page from any other data display or a setup menu.
If the Auto-Scroll feature is enabled, the display immediately enters

the auto scroll sequence.
Auto-Scroll
If the Auto-Scroll feature is enabled, the data display automatically

scrolls through all pages of all data displays that are included into the
programmable auto-scroll sequence. The scroll interval is adjustable in
the range of 2 to 30 seconds. The scroll sequence may include all or
only selected displays.
The display automatically enters auto scrolling if no button is pressed

for the Auto-Return interval when the Auto-Return feature is enabled
or in 1 minute if this feature is disabled. In the last case, the scroll
sequence is restored from the point where it was interrupted.
To stop auto scrolling, press briefly any button if the backlight is on;
else press briefly any button twice since the first press only sets the
backlight on and does not affect auto scrolling.
Auto-Scroll is not operational in TEST mode.

‎Chapter 3 Using Front Display Data Displays
Measurement Units
The following table shows the display resolution for common displayed
quantities. All measured data is displayed in primary units.
Measured Voltage Connection Units and Display Resolution
Quantity
Energy kWh, kvarh, kVAh with one decimal
place. The number of digits is
programmable (see Device Options
and Mode Control in Chapter 5).
Power Direct kW, kvar, kVA with three decimal
(PT = 1.0) places
Transformer MW, Mvar, MVA with three decimal
(PT>1.0) places
Voltage Direct Volts with one decimal place
(PT = 1.0)
Transformer Kilovolts with three decimal places
(PT>1.0)
Current Amperes with two decimal places
3.2 Data Displays

The EM13X Series has 7 multi-page data displays listed in the following
table.
Display Sequence Display type Display Contents
1 Billing/TOU reg. Energy billing period data
2 TOU/Max. DEMAND Max. DMD Power billing period
data
3 Energy Total and Phase Energy data
4 MAX. DEMAND Engineering maximum demands
5 Measurement Instrumentation data
6 Phase Rotation Phase, I/O and Counter data
7 Diagnostics Device diagnostics messages and
Device service data
TEST Mode Data Display

The TEST data display is shown in TEST mode in place of the billing
period data displays, "NORM" is replaced by "TEST". See Device
Options and Mode Control in Chapter 5 on how to enter the meter
TEST mode.
DISPLAY Description
TEST mode display: test LED pulse rate in

11:13:11 TEST secondary Wh/imp, test kWh and kvarh
energy registers readings in primary units
20/09/2011 T1 - with an extended 0.001 kWh resolution.
Billing Period Energy Data Displays

The EM13X Series provides billing period data displays for energy and
general purpose volume data as m³, cf or Ccf calculated using Digital
Input for water and/or gas meter application.
Only registers you selected in the billing/TOU register setup and tariff
rates listed in the TOU daily profiles are included (see Configuring
Billing/Tariff Registers and Configuring the Daily Tariff Schedule in
Chapter 5).

The following example demonstrates the present billing period displays

for two configured billing registers (kWh imported and kvarh imported)
and for three active tariff rates. The actual register contents in your
installation may be different depending on your selection of register
sources.
DISPLAY Description
Total Import Active energy data.
Billing period according to TOU predefined
profile (Reg1 for TOU actve energy and
Reg 1 Imp Reg2 for TOU reactive energy are
725 kWh predefined TOU/Register factory setup,
can be changed by user, see Configuring
Billing/Tariff Registers and Configuring the
Daily Tariff Schedule in Chapter 5)
Reg 1/T1 Imp

Tariff 1 Import Active energy data.
517 kWh
Reg 1/T2 Imp

114 kWh
Reg 1/T3 Imp

94 kWh
Reg 2 Imp
Total Import Reactive energy data.
221 kvarh
Reg 2/T1 Imp

Tariff 1 Import Reactive energy data.
165 kvarh
Reg 2/T2 Imp

35 kvarh
Reg 2/T3 Imp

21 kvarh
Single Phase billing data1

Total Import Phase 1 active energy data
Tariff 1 Import Phase 1 active energy

data.
1
Only from S/W V12.2.1


data.

data.

data.

data.

data.

data.

data.

data.
TOU/Maximum Demand Power Data Display

The following example demonstrates the TOU/Maximum Demand
displays for three configured registers (MAX kW imported, MAX kvar
imported and MAX kVA imported) and for three active tariff rates. The
actual register contents in your installation may be different depending
on your selection of register sources.
DISPLAY Description

DISPLAY Description
Total Import Max. DMD active power data
(Reg1 for TOU/Max. DMD actve power,
Reg 1 Imp MAX Reg2 for TOU/Max. DMD reactve power
predefined TOU/Register factory setup,
0.008 kW can be changed by user, see Configuring
Billing/Tariff Registers and Configuring the
Daily Tariff Schedule in Chapter 5)
Reg 1/T1 Imp MAX Tariff 1 Import max. active power dmd
0.008 kW data.
0.008 kW data
0.002 kW data
Reg 2 Imp MAX Total Import Max. DMD reactive power

data
0.003 kvar
Reg 2/T1 Imp MAX Tariff 1 Import max. reactive power dmd
0.003 kvar data.
0.003 kvar data.
0.001 kvar data.
Reg 3 Imp MAX Total Import Max. DMD apparent power

data
0 kVA
Reg 3/T1 Imp MAX Tariff 1 Import max. apparent power dmd
0 kVA data.
0 kVA data.
0 kVA data.

Instrumentation Measurement Maximum Demand Data Display

Maximum demand displays show engineering maximum demands (not
billing maximum demands) for import/export powers, voltages, and
currents.
DISPLAY Description
MAX. DMD
Total Import Max. DMD active power data
P Imp 0.008 kW
MAX. DMD
Total Export Max. DMD active power data
P Exp 0 kW
MAX. DMD Total Import Max. DMD reactive power

Q Imp 0.003 kvar data
MAX. DMD Total Export Max. DMD reactive power

Q Exp 0 kvar data
MAX. DMD Total Import Max. DMD apparent power

S 0.008 kVA data
MAX. DMD
Max. DMD Phase 1 current data
I1 0 A
MAX. DMD
I2 0 A
MAX. DMD
I3 0 A
MAX. DMD
Max. DMD neutral current data
In 0 A
MAX. DMD
Max. DMD Phase 1 voltage data
V1 0 V
MAX. DMD
V2 0 V

MAX. DMD
V3 0 V
Instrumentation Measurement
Instrumentation Measurements represent general instrumentation data
you can use while installation and inspecting the meter. Use phase
angles displays to check the order of phases when connecting wires to
the meter terminals.
DISPLAY Description
V1 0 V V1 and V2 Phase-to-neutral voltages.

Only displayed in 4-wire configurations
V2 0 V with a neutral.
V3 0 V
V2 Phase-to-neutral voltage
V12 0 V
Phase-to-Phase voltages.
V23 0 V
V31 0 V
Phase-to-Phase voltages.
I1 0 A
Phase currents.
I2 0 A
I3 0 A Phase currents, neutral current is

In 0 A calculated.
P 0 kW
Total powers.
Q 0 kvar
S 0 kVA Total apparent power and total power

PF 0 factor
L1 P 0 kW
Phase 1 active and reactive power
L1 Q 0 kvar

DISPLAY Description
L1 S 0 kVA
Phase 1 apparent power and power factor
L1 PF 0
L2 P 0 kW
L2 Q 0 kvar
L2 S 0 kVA
L2 PF 0
L3 P 0 kW
L3 Q 0 kvar
L3 S 0 kVA
L3 PF 0
H1 P 0 kW
First Harmonic Total powers.
H1 Q 0 kvar
H1 S 0 kVA First Harmonic Total apparent power and

H1 PF 0 total power factor
H1/L1 0 kW First Harmonic Phase 1 active and

H1/L1 0 kvar reactive power
H1/L1 0 kVA First Harmonic Phase 1 apparent power

H1/L1 0 PF and power factor




DISPLAY Description

V1 THD 0 %
Phase 1 voltage and current THD
I1 THD 0 %
V2 THD 0 %
I2 THD 0 %
V3 THD 0 %
I3 THD 0 %
I1 TDD 0 %
Total Demand current Distortion
I2 TDD 0 %
I3 TDD 0 %
Total Demand current Distortion
V Unb 0 %
Voltage and Current unbalance
I Unb 0 %
Freq 0 Hz
Frequency
V1 Ang 0° Voltage and Current Phase 1 angles

I1 Ang 0° (relative to V1 voltage)


Status Inputs and Outputs
DISPLAY Description

DISPLAY Description
Phase Rotation: Phase rotation order (Error, Positive,

Error Negative)
DI: 123456
Digital Inputs status
000000
Relays: 123
Relays control status
000
Counter 1:
Status/Event Counter 1
0
Counter 2:
0
Counter 3:
0
Counter 4:
0
Device Info Display

The device info display provides different service information that may
be required for meter identification and inspection, like product and
firmware information, communication settings, and so on, and shows
device diagnostic messages recorded as a result of the meter self-test
diagnostics during start-up and operation.
If there are diagnostic messages, Some of the diagnostics events are

cleared automatically as the event source disappears. See Device
Diagnostic Codes in Appendix G for a full list of diagnostic messages
and their meanings. See Clearing Device Diagnostics for information on
how to clear the device diagnostics from the display and via PAS.
The diagnostic icon can be disabled or enabled via the Display Setup
menu.
DISPLAY Description
Diagnostics:
Power Down message
8

DISPLAY Description
S/N: 12345744 Meter identification info, serial number

S/W: V12.1.1 and device SW version
Boot: V1.1.1
Boot SW version and Modem setup
Modem: N/A
COM1: a221,b115.2
Communication port COM1 info
Modbus RTU
COM2: RF, a221

Modbus RTU
COM3: a1,b19.2
Modbus RTU

‎Chapter 3 Using Front Display Programming Mode
3.3 Programming Mode

To enter programming mode from the data display, press and hold the
SELECT/ENTER button for more than 5 seconds.
Navigation Buttons
The following table gives a summary of the button operations in
programming mode.
Button Press Operations
SCROLL Short press Scroll through a menu item list in a
highlighted window or increment a
highlighted digit in a numeric field
SELECT/ENTER Short press (less than Highlight a menu window or a digit in a
1 second) = SELECT numeric field
SELECT/ENTER Long press (1 to 2 Store the changed item or perform an
seconds) = ENTER action indicated in a highlighted window
Entering Numeric Values
Basic PT Ratio Whenever a numeric value is to be changed, use a short press on the
100.0 SELECT/ENTER button to highlight a desired digit, and then use the
SCROLL button to change the value of the highlighted digit. A
SHORT PRESS
highlighted digit appears in inversed color. If you missed a digit, just
Basic PT Ratio continue moving through the rest of digits until you reach the desired
100.0 place.
Once the number is set to the desired value, press and hold the
Basic PT Ratio SELECT/ENTER button for 1-2 seconds to save your new setting.
150.0
LONG PRESS
To reject your changes and restore the previous value, use a short
press on the SELECT/ENTER button to return to the higher-level
window.
Password Security
The setup menus are secured by 8-digit user passwords. Every time
Enter Password you enter programming mode, you are prompted for a correct
00000000 password. The meter is primarily shipped with all passwords preset to
9 at the factory.
SHORT PRESS
Enter Password It is recommended that you change the factory set passwords as fast
00000009 as possible to protect your setups and accumulated data from
LONG PRESS unauthorized changes. See Configuring Meter Passwords in Chapter 5
on how to change passwords in your meter.
Enter the password as you enter numeric values. As you move to the
next place, the digit entered is saved and then zeroed. If you missed a
digit, you should re-type all preceding digits before you reach the
missed place again.
Once the password is set to the desired value, press and hold the
SELECT/ENTER button for more than 1 second. If the password you
entered is correct, you move to the main device menu, otherwise you
return back to the data display.
Setup Menus and Access Rights

The EM13X Series setup is menu-driven. The meter provides 11 menus
that allow local accessing a limited number of meter setups and control

functions listed in the following table. Access to particular menus is

granted depending on the security level of the password you entered.
Menu Menu Function Security Level

Label View Change
Reset Reset of billing and engineering maximum Low See
demands, device diagnostics, meter and failure Table
counters below
RTC RTC clock setup Low Low
Basic Basic device setup Low High
Options Device options setup Low High
COM1 COM1 serial port setup Low Medium
Local Local settings Low Medium
Disp Display setup Low Low
Access Meter passwords setup High High
Loader Launches flash download via a local serial port Medium Medium
Access to the RESET menu entries is allowed depending on your

security level.
If your security level does not allow access to a menu, it will not be
listed in the main menu list, and you will not be able to highlight menu
items that you are not allowed to change, but you can still view their
present settings.

Viewing and Changing Setup Options

Once you entered a correct password you are moved to the main
Enter Password meter menu.
00000000
SHORT PRESS The main menu has two windows: the left window displays a submenu
list, while the right window is an assisting Exit window that allows easy
Enter Password returning back to the data display. A currently active menu item is
00000009
highlighted by flashing.
LONG PRESS
To select a desired menu entry from the menu list:

Reset Exit
If the left window is not highlighted yet, highlight it by briefly pressing
SCROLL until
Disp menu
the SELECT/ENTER button.
Disp Exit
Use the SCROLL button to scroll through the menu list until the desired
menu entry appears
LONG PRESS
Press the SELECT/ENTER button for more than 1 second to enter the
Disp Autoscroll
5
selected submenu.
SHORT PRESS Once you entered a submenu, the left window is still showing the menu
name, while the upper-right window represent a submenu options list,
Disp Autoscroll
5 and the lower-right window indicates the present option value.
SCROLL To select an option you want to view or change:

Disp Autoscroll
Disabled Use the SCROLL button to scroll through the option list until the
desired option’s name appears in the window.
LONG PRESS
Disp Autoscroll To change the selected option’s value:

Disabled Press the SELECT/ENTER button briefly to highlight the lower-right
LONG PRESS
window.
If an option is represented by a list of values, use the SCROLL button
Disp Exit to scroll through the list until a desired value appears in the window. It
an option is represented by a numeric value, use the SCROLL button to
SHORT PRESS adjust each digit to the desired value, and use a short press on the
SELECT/ENTER button to move through digits.
Disp Exit
Once the desired value is selected, press the SELECT/ENTER button for
more than 1 second to save your new setting. You return to the upper-
LONG PRESS right window and can continue scrolling through the rest of options or
can return to the main menu
10:57:00 NORM
22/09/2011 T1 -
If you wish to leave the option value unchanged, use a short press on
the SELECT/ENTER button to return to the upper-right window.
To exit the submenu and return to the main menu:

 If the upper-right window is not highlighted yet, highlight it by briefly
pressing the SELECT/ENTER button.
 Press the SELECT/ENTER button for more than 1 second. You will return
to the main menu.
To exit the main menu and return to the data display:

 Press briefly the SELECT/ENTER button to highlight the right-upper Exit
window.
 Press the SELECT/ENTER button for more than 1 second. You will return
back to the data display.

‎Chapter 4 Using PAS Software Installing PAS
Chapter 4 Using PAS Software

The support PAS software is a configuration and data acquisition tool
that allows you to configure all of the EM13X Series features, monitor
your meters on-line, retrieve recorded files and view reports. PAS can
communicate with your EM13X Series via a serial port and via the
Ethernet.
This chapter gives information on how to install and run PAS on your
computer, and how to prepare information for your meter using PAS.
4.1 Installing PAS

You need PAS V1.4 Build 5 or higher to take an advantage of the meter
data logging options.
To install PAS on your PC:

Insert the installation CD supplied with your meter into CD drive.
Open My Computer on your Desktop.
P Click on your CD drive icon, select the PAS directory, and then double
A click on Setup (shown as an Application type file).
S
S
Follow InstallShield® Wizard instructions on the screen.
A
S PAS is installed by default to the C:\Pas folder.
When installation is complete, the PAS icon appears on your Desktop.
Double click on the PAS icon to run PAS.
For general information on how to work with PAS, see the “PAS Getting
Started” guide supplied on the installation CD.
4.2 Creating a New Site for your Meter

PAS keeps all communication and configuration data for your meter in
a configuration database called a site database. During configuration,
store all setup data to the site database so that PAS recognizes device
properties regardless of whether the meter is online or offline.
To communicate with the meters, create a separate site database for

each device.
To create a new database for your meter:

Select Configuration from the Tools menu.

‎Chapter 4 Using PAS Software Creating a New Site for your Meter
Figure ‎4-1: Configuration Dialog Box – Instrument Setup Tab
Click the Sites button on the right-hand-side.
From the Look in box, select the directory where a new database will
be stored. By default, it is the Sites directory.
Type a site name for your device in the File name box, click New, and
then click OK.
On the Instrument Setup tab, select EM13X Series in the Model
box. PAS automatically selects the appropriate instrument options for
your meter.
Select a correct CT secondary current (5A or 1A) for your meter.
If you wish to add any comments for your meter, type the comments
in the Comment box.
For more device configuration details using PAS™ Software refer to

PM130 PLUS Installation and Operation Manual BG0425 REV.12

‎Chapter 5 Configuring the EM13X Series Configuring Communications
Chapter 5 Configuring the EM13X

Series
This chapter describes how to configure the EM13X Series for your
particular environment and application from the front display and via
PAS. To access your meter configuration options via PAS, you should
create a site database for your device as shown in Chapter 4.
5.1 Configuring Communications

Setting Up Serial Communication Ports
Using the Front Display
COM1 Protocol
Select COM1 through COM3 from the main menu. See Viewing and
Modbus RTU
Changing Setup Options in Chapter 3 for information on navigating in
menus.
See the table below for available communication options.

Using PAS
Select Communications Setup from the Meter Setup menu, and then
click on the Serial Ports Setup tab. In the Port box, select the desired
device port.
Figure ‎5-1: Communication Setup Dialog Box – Serial Ports Setup Tab

To change the port settings in your device, select desired port

parameters, and then click Send.
The following table lists available port options.
Table 4: COM Port Options

Display Label Parameter Options Default Description
Protocol Communication MODBUS RTU, MODBUS MODBUS RTU The
protocol ASCII, DNP3, SATEC (COM 1-3) communications
ASCII, IEC 60870-5 protocol for the
port
Interface Port interface RS485, RS232, IR, RS485 Not changeable;
GPRS1, ETHERNET, (COM1) automatically
PROFIBUS, CANopen RS232 detected by the
(COM2) IR meter
(COM3)
Address Device address MODBUS: 1-247 1 Device network

DNP3: 0-65532 address
IEC 60870-5: 1-4095
Baud Rate Baud rate COM1: 300-115.2 kbps, 19.2 kbps The port baud
COM2: 300-115.2 kbps rate
COM3: 9600-38400
kbps
Data/Parity Data format 7E, 8N, 8E 8N 7E data format
and parity should not be
used with the
MODBUS RTU and
DNP3 protocols
Send Delay Response delay 0-1000 ms 5 ms The minimum
time after the last
request character
is received to start
the transmission.
Chr.Timeout Character 0-1000 ms 4 ms The maximum
timeout time the line is
allowed to idle
before closing a
connection in the
MODBUS RTU and
DNP3 protocols
The meter automatically detects replaceable communication modules

and does not allow you to change the baud rate and data format for
the Dial-up GSM/GPRS3 modem.
1
GPRS – also covers 3G & 4G network

Setting up the Ethernet

Select Net from the main menu. See Viewing and Changing Setup
Net IP Address
Options in Chapter 3 for information on navigating in menus.
192.168.000.203
See the table below for available network options.
Using PAS
Select Communications Setup from the Meter Setup menu, and then
click on the Network Setup tab.
Figure ‎5-2: Communication Setup Dialog Box – Network Setup Tab
The following table lists available network options.

Table 5: Ethernet Setup Options
Display Label Parameter Default
IP Address Device IP Address 192.168.0.203
Subnet Mask Network Subnet Mask 255.255.255.0
Def. Gateway Network Default Gateway 192.168.0.1
TCPServicePort 502 = Modbus/TCP 502
20000 = DNP3/TCP
NOTES
 The meter provides the permanent MODBUS TCP server on port 502.
 Selecting the DNP3 TCP service port launches the second DNP3 TCP
server allowing simultaneous connections on both TCP ports. Selecting
the Modbus TCP port disables the DNP3 TCP server.
The TCP service port can also be changed trough the COM2 serial port setup.
Changing the communication protocol for the port automatically changes the
TCP port for the Ethernet.
 When you change the device network settings through the Ethernet port,
the device port restarts so communication will be temporarily lost. You
may need to wait some additional time until PAS restores a connection
with your device.Setting-Up Dial-Up GPRS Network

Setting up GPRS Network

The EM13X Series can provide wireless Cellular communications with

the remote Modbus/TCP server via an external Enfora GSM1308 SA-G+
GSM/GPRS modem. See Connecting a GSM/GPRS modem in Chapter 2
on how to connect a modem to your meter.
Using PAS
 Select Communications Setup from the Meter Setup menu, and then
click on the GPRS Setup tab.
Select Communications Setup from the Meter Setup menu, and
then click on the GPRS Setup tab.
Figure ‎5-3: Communication Setup Dialog Box – GPRS Setup Tab

The following table lists available GPRS options.

Table 6: GPRS Setup Options
Parameter Default Description
Access Point Name (APN) internetg The mobile network APN name
User name Username (if required)
Password Password (if required)
GPRS Mode Client mode Can also be configured as server
 Configure your mobile network APN, username and password. Consult
your network operator regarding proper network settings. Leave the
username and password fields blank if network authorization is not
required.
 Send your GPRS settings to the meter.
 Select the GPRS interface in the COM2 port setup (see Setting Up Serial
Communication Ports).
 Configure your eXpertPower client (see Setting Up eXpertPower Client)
or/and TCP Notification client (see Setting Up TCP Notification Client) for
communicating with a remote server.
You can check the status of the GPRS communications from the front
panel via the Status Display or via the Device Control dialog in PAS
(see Viewing Communication Status and Statistics).
Setting Up WiFi Network

WiFi communications is available in the meters equipped with a WiFi
expansion module.
Make sure the power is off before

attaching a WiFi expansion module to
the meter to avoid damage to sensitive
electronic components.
A WiFi module can be configured to work in one of the following

modes:
a) as a regular WiFi station for connection of the meter to an existing
WiFi network;
b) as a WiFi access point/router to create a separate secured WiFi
network without using an additional external router. It also serves as
a network gateway for the connected meter.
When access point mode is disabled (see instructions below), the

module operates as a regular WiFi station.
Use the accompanying PAS software to configure WiFi communications

in your meters.
Configuring WiFi Station Parameters
Skip this section if the WiFi module is to be configured as an access

point/router since the network parameters for the meter will be
automatically set up.
To connect your meter to the existing wireless network, select

Communication Setup from the Meter Setup menu and click on the
WiFi Station Setup tab.

Configure the wireless network parameters as follows:
Network Name (SSID) – the wireless network name you want to

connect to. The default factory preset network name is DEVICE-NET.
Security/Encryption Type – the WiFi security and data encryption

method set for the wireless network in the network router.
Security Key – the pass phrase to authenticate the meter with your
wireless network.
If you connect the meter to a SATEC WiFi network, use same network
authentication parameters as you configured for the network access
point/router (see Section 3 below).
If you connect the meter to a foreign WiFi network, you can identify
the wireless network parameters via the Windows Network and Sharing
Center on your PC connected to the WiFi network:
On Windows 7 and 8.1, click the Start button, and then open the
Control Panel. Select Network and Internet -> Network and Sharing
Center.
On Windows 10, click the Start button, then select Settings -> Network
& Internet -> Status -> Network and Sharing Center.
In Network and Sharing Center, next to Connections, select your WiFi

network name. In Wi-Fi Status, select Wireless Properties, and then
click on the Security tab to see the network security type and
encryption method. Check the Show characters check box to see
your WiFi network security key.

Configuring WiFi Access Point/Router Mode
To configure a WiFi module as a WiFi access point, select

Communication Setup from the Meter Setup menu and click on the
WiFi Access Point Setup tab.
The following explains the network parameters you need to configure

for your wireless network:
Access Point Enable – defines the WiFi module operation mode:

Disabled = WiFi station mode, Enabled = WiFi Access Point/Router
mode.
Network Name (SSID) – the wireless network name (service set

identifier) that uniquely identifies your wireless network among other
neighboring networks – 1 to 15 ASCII characters long. The default
network name is DEVICE-NET.
WiFi Protocol – the WiFi physical layer protocol that defines the
supported WiFi network technology and network bandwidth. If you find
it difficult to choose the right one to cover all technologies supported
by your network devices, it’s recommended that you leave the default
802.11b/g/n protocol setting.
WiFi Channel – selects the working network channel (frequency band)

among 11 available channels. You can select a fixed channel or set it to
AUTO mode (factory default) so that the module will automatically
select the most reliable channel for your network.
LAN IP Address – the network router IP address. It also defines the

range of addresses (address segment, or network prefix) to be used
across your wireless network. It is recommended to use private (non-
routable) address segments you can select from the following ranges:
10.0.0.1 – 10.255.255.254
172.16.0.1 – 172.31.255.254
192.168.0.1 – 192.168.255.254
The default factory set wireless LAN router address is 10.10.1.254.
LAN Subnet Mask – specifies the network prefix part of the IP

addresses (address segment) for your wireless network. The default
255.255.255.0 mask defines the network prefix as 10.10.1.XXX, where
XXX – the host part of 1 to 254 you can assign to wireless devices
connected to the network.
Security/Encryption Type – the WiFi security and data encryption

method for your wireless network. The default WPA/AES setting is
chosen meaning the support of most available wireless devices. For
higher security, select WPA2/AES as the most secure option that is
now the current standard for WiFi security.

Security Key – the pass phrase (password) that will be used to

authenticate connected devices with your wireless network. Depending
on the selected security type, the security key length should be as
follows:
WEP – 5 or 13 ASCII characters (64-bit or 128-bit key respectively)
WPA and WPA2 – 8 to 15 ASCII characters.
The factory-set temporary security key is “12345678”. For highest

security, use WPA2/AES encryption with a randomly selected security
key.
Configuring Network IP Addresses
SATEC meters use fixed network addresses rather than dynamic

address configuration to avoid receiving a random address every time
the meter is reconnected to a WiFi network.
NOTE: The meter connected to a WiFi access point/router

should be provided with a network address different from the
LAN/router IP address like any other WiFi device.
You can configure the network address in your meter either from the
meter front display (see the meter operation manual for more
information), or via PAS.
To configure the meter address via PAS, select Communication Setup

from the Meter Setup menu and click on the Network Setup tab.

Configure the meter’s wireless network address as follows.
If your meter is connected to a SATEC WiFi network, set the default

gateway and the network subnet mask to the LAN IP address and LAN
subnet mask as you configured for the WiFi network access points in
Section 3. For the device IP address, use the WiFi network prefix
(address segment) with a host part in the range of 1-99 or 200-254.
Host addresses 100 to 199 are reserved for dynamic configuration of
the devices and computers connected to the network using DHCP
protocol.
If you connect the meter to a foreign WiFi network, you can identify
the default gateway address and subnet mask via the Windows
Network and Sharing Center on your PC connected to the WiFi network
as shown above in Section 2. In Network and Sharing Center, next to
Connections, select your Wi-Fi network name. In Wi-Fi Status, select
Details. Consult with the network administrator for the
applicable host IP addresses, or select one within the network
address segment that has not yet been assigned to any host across
the WiFi network.
Monitoring a WiFi Connection
If your WiFi module is properly configured, the meter will automatically

connect to the WiFi network any time the meter is restarted.
You can monitor the connection status and signal quality via the meter
front display or via PAS.
To check a WiFi connection from the meter display:

In the EM133, move to the Diagnostics display and then scroll to the
“WiFi” page where you can see the network connection status and
received signal quality. The following page indicates the meter network
address.
In the PM130, move to the STA display and then scroll to the “rSSi”
page where you can see the received signal quality in percent followed
by the network connection status.
In the PM135, move to the Device Info display and then scroll to the
“WiFi” page.
To check a WiFi connection via PAS, select Device Control from the
Monitor menu and click on the Communications tab. The connection
status and received signal quality are indicated under the WiFi Wireless
Communications section.
Setting Up eXpertPower Client

The PM130 PLUS has an embedded eXpertPowerTM client that provides
communications with the eXpertPowerTM server – the SATEC
proprietary Internet services. Connections to the eXpertPower TM server
are handled on a periodic basis.
To set up communications with the eXpertPowerTM server, select

Communication Setup from the Meter Setup menu, and then click
on the ExpertPower Client Setup tab.

Figure ‎5-4: eXpertPower Client Setup Tab
The following table lists available options. Refer to your eXpertPower

service provider for the correct network settings.
Table 6: eXpertPower Client Setup Options
Parameter Options Default Description
XPW Server IP Address 207.232.60.18 The IP address of the
eXpertPower server
XPWServerPort 0-65535 5001 The TCP service port of the
eXpertPower server
XPW Client Enabled NO, YES NO Enables operations of the
eXpertPower client
Time to Next Session, 1-99999 The time remaining to the
min next connection session
NOTES
 Do not enable the eXpertPower client in your meter if you do not use the
eXpertPowerTM service.
 Do not change the connection time setting. It is for information only. The
eXpertPower server updates it automatically.
Setting Up TCP Notification Client

The TCP notification client can establish connections with a remote
Modbus/TCP server and send notification messages either on events,
or periodically on a time basis.
To set up communications with a remote TCP Notification server, select

Communication Setup from the Meter Setup menu, and then click
on the TCP Notification Client Setup tab.

‎Chapter 5 Configuring the EM13X Series General Meter Setup
Figure ‎5-5: TCP Notification Client Setup Tab
The following table lists available client options.

Table 7: TCP Notification Client Setup Options
Client Enabled NO, YES NO Enables operations of the
notification client
Server IP Address 192.168.0.3 The IP address of the notification
server
ServerPort 0-65535 502 The TCP service port of the
notification server
Message Exchange 0-65535 1000 The start address of a block
Address of 16 Modbus registers for receiving
notification messages
Connections with a remote server are triggered via programmable

setpoints. To send event notifications to a server, configure a setpoint
to respond to desired triggers or to periodic time events and put the
"Notification" action to the setpoint action list (see Configuring
Alarm/Control Setpoints).
See the PM130 PLUS Modbus Reference guide for more information on
operation of the notification client and the notification message
structure.
5.2 General Meter Setup

Basic Meter Setup
This section describes how to configure the EM13X Series for your
particular environment and application.
Before operating your meter, provide the device with basic information
about your electrical network.

Select the Basic entry from the main menu. See Viewing and Changing
Basic Exit
Setup Options in Chapter 3 for information on configuring parameters
via the front display.
LONG PRESS
See the table below for the Basic Setup options.
Basic Conf
4Ln3
SCROLL until
CT menu
Basic CT
50

Using PAS
Select General Setup from the Meter Setup menu. See the table
below for the Basic Setup options.
Table 8: Basic Setup Options

Display Parameter Options Default Description
Label
Conf Wiring Mode See Table 9 4Ln3 The wiring connection of the device
PT Ratio PT Ratio 1.0-6500.0 1.0 The phase potential transformer’s
primary to secondary ratio
PT Factor PT Ratio Multiplier ×1, ×10 ×1 PT Ratio multiplication factor. Used
in extra high voltage networks to
accommodate the PT ratio for
500 kV and higher networks.
CT CT Primary Current 1-50000 A 5A The primary rating of the phase
current transformer
PowDmdPer Power block 1, 2, 3, 5, 10, 15, 15 min The length of the demand period
demand period 20, 30, 60 min, for power demand calculations. If
E=external sync the external synchronization is
selected, a pulse front on the
digital input DI1 denotes the start
of the demand interval.
Num.Per. The number of 1-15 1 The number of blocks to be
blocks in the averaged for sliding window
sliding demand demands
window
ADmdPer. Volt/Ampere 0-1800 sec 900 sec The length of the demand period
Demand Period for ampere and volt demand
calculations
Freq Nominal Frequency 50,60,25,400 Hz 60 Hz The nominal line frequency
MaxDmdLd Maximum Demand 0-50000 A 0 The maximum demand load
Load Current current (0 = CT primary current)
1. Always specify the wiring mode and transformer ratings prior to setting up
setpoints and analog outputs.
2. The maximum value for the product of the phase CT primary current and PT
ratio is 57,500,000. If the product is greater, power readings are zeroed.

Figure ‎5-6: General Setup Dialog Box – Basic Setup Tab
Table 9 lists the available wiring modes.
Table 9: Wiring Modes

Wiring Mode Description
3OP2 3-wire Open Delta using 2 CTs (2 element)
4LN3 4-wire Wye using 3 PTs (3 element), line-to-neutral voltage readings
3DIR2 3-wire Delta Direct Connection using 2 CTs (2 element)
4LL3 4-wire Wye using 3 PTs (3 element), line-to-line voltage readings
3OP3 3-wire Open Delta using 3 CTs (2½ element)
3LN3 4-wire Wye using 2 PTs (2½ element), line-to-neutral voltage
readings
3LL3 4-wire Wye using 2 PTs (2½ element), line-to-line voltage readings
3BLN3 3-wire Broken Delta using 2 PTs, 3 CTs (2½ element), line-to-neutral
voltage readings
3BLL3 3-wire Broken Delta using 2 PTs, 3 CTs (2½ element), line-to-line
voltage readings
In 4LN3, 3LN3 and 3BLN3 wiring modes, Min/Max volts, volt demands and
voltage harmonics represent line-to-neutral voltages; otherwise, they will be
line-to-line voltages.

Device Options
The Device Options setup allows changing user-configurable device
options or putting the meter into energy test mode.
Select Options from the main menu. See Viewing and Changing Setup
Options TestMode
Options in Chapter 3 for information on configuring parameters via the
OFF front display.
Using PAS
Select General Setup from the Meter Setup menu, and then click on
the Device Options tab.
Table 10 lists available device options.
Table 10: User-configurable Device Options

Label
TestMode Energy Test Three options: Disabled Setting this option puts the
Mode OFF = disabled meter into the energy test
Wh pulses mode (see Energy Pulse
varh pulses LED in Chapter 3)
PowMode Power Reactive = using reactive power S=f(P, Q) The method used for
Calculation S=f(P, Q), calculating reactive and
Mode NonActive = using non-active apparent powers (see
power Q=f(S, P) Power Calculation Modes
below)
EngyRoll Energy Roll 10000 = 10000 kWh 10000000 The value at which energy
Value 100000 = 100000 kWh counters roll over to zero
1000000 = 1000000 kWh
10000000 = 10000000kWh
100000000 = 100000000 kWh
1000000000 = 1000000000 kWh
Phs.Engy Phase Energy Disabled Disabled Enables phase energy
Calculation Enabled calculations
StrtVolt Starting 1.5-5.0% 1.5% The device starting voltage

Voltage in percent of FS (120V or
400V)
Resolution Device Low Low The voltage, current and
Resolution High power resolution on the
front display (see
Measurement Units in
Chapter 3) and in
communications (see
communication guides)

Figure ‎5-7: General Setup Dialog Box – Device Options Tab
Power Calculation Modes
The power calculation mode option allows you to change the method
for calculating reactive and apparent powers in presence of high
harmonics. The options work as follows:
 When the reactive power calculation mode is selected, active and
reactive powers are measured directly and apparent power is
calculated as:
S  P2  Q2

 This mode is recommended for electrical networks with low harmonic

distortion, commonly with THD < 5% for volts, and THD < 10% for
currents. In networks with high harmonics, the second method is
preferable.
 When the non-active power calculation mode is selected, active

power is measured directly, apparent power is taken as product S =
V x I, where V and I are the RMS volts and amps, and reactive power
(called non-active power) is calculated as:
 N  S2  P2
Configuring Digital Inputs

The EM13X Series can be provided with two digital inputs (standard)
and 4, 8 or 12 optional digital inputs that can be linked to control
setpoints to give an indication on input status change (see Configuring
Alarm/Control Setpoints), or can be linked to general pulse counters to
count incoming pulses (see Configuring Counters). They can also be
linked to the Billing/TOU registers to count pulses from external
wattmeters or gas and water meters.

Using PAS
the Digital Inputs tab.
Figure ‎5-8: General Setup Dialog Box – Digital Inputs Dialog Box
The available options are shown in Table 11.

Table 11: Digital Inputs Options
Parameter
T Options Default Description
Input
h Polarity NORMAL NORMAL For the normal polarity, the open
e INVERTING to closed transition is considered
closed. For the inverting polarity,
the closed to open transition is
d
considered a closed
e
Pulse
b Input PULSE MODE PULSE In pulse mode, either leading, or
Mode KYZ MODE MODE trailing edge of the input pulse is
o
recognized as an event. In KYZ
u mode, both leading and trailing
n edges of the input pulse are
c recognized as separate events.
e Polarity
Pulse NORMAL (N.O.), NORMAL For the normal polarity, the open
INVERTING (N.C.) to closed transition is considered
t a pulse. For the inverting polarity,
i the closed to open transition is
m considered a pulse.
e It has no meaning in KYZ mode
where both transitions are used.
Debounce
i 1-100 ms 10 ms The amount of time while the
Time
s state of the digital input should
not change to be recognized as a
new state. Too low debounce time
a could produce multiple events on
p the input change.
a
The debounce time is applied the same for all digital inputs. If you
change the debounce time for a digital input, the same debounce time
is automatically assigned to the others.
Configuring Relay Outputs

The PM130 PLUS can be provided with one relay (standard) and 2 or 4
optional relay outputs. Each relay can be operated either locally from
the alarm/control setpoints in response to an event or by a remote
command sent through communications. It can also be linked to an
internal pulse source to produce energy pulses.
Using PAS
the Relay Outputs tab.

Figure ‎5-9: General Setup Dialog Box – Relay Outputs Tab

The available relay outputs options are shown in Table 12.
Table 12: Relay Output Options

Operation UNLATCHED UNLATCHED Unlatched mode: the relay
mode LATCHED goes into its active state
PULSE when the control setpoint is
KYZ in active (operated) state,
and returns into its non-
active state when the setpoint
is released.
Latched mode: the relay goes
into its active state when the
control setpoint goes into
active state and remains in
the active state until it is
returned into its non-active
state by a remote command.
Pulse mode (normal pulse):
the relay goes into its active
state for the specified time,
goes into non-active state for
the specified time and
remains in the non-active
state.
KYZ mode (transition pulse):
the relay generates transition
pulses. The relay changes its
output state upon each
command and remains in this
state until the next
command.
Polarity NORMAL (N.O.) NORMAL Normal polarity: the relay is
INVERTING normally de-energized in its
(N.C.) non-active state and is
energized in its active
(operated) state.
Inverting polarity: the relay is
normally energized in its non-
active state and is de-
energized in its active
(operated) state. It is called
failsafe relay operation.
Pulse width 20-1000 ms 100 ms The actual pulse width is a
multiple of the 1-cycle time
rounded to the nearest bigger
value.
The pause time between
pulses is equal to the pulse
width.
Pulse source NONE NONE Links a pulse relay to the
Ac.Ei = kWh IMP internal energy pulse source.
Ac.EE = kWh EXP The relay must be set into
rE.Ei = kvarh IMP either pulse, or KYZ mode.
rE.EE = kvarh
EXP
rE.Et = kvarh
TOT
AP.Et = kVAh
TOT
Pulse rate, 0.1-1000.0 1.0 Defines the pulse weight in
kWh/Pulse kWh/Pulse kWh units per pulse

Generating Energy Pulses through Relay Outputs

To generate energy pulses through a relay output:
 Set a relay to either pulse, or KYZ mode, and then select a polarity
(active pulse edge) for energy pulses and a pulse width.
 Select a source energy accumulator and the pulse rate for your output
 Send your new setup to the meter
Configuring Analog Outputs

The meter can be ordered with four optional analog outputs with
options for 0-1mA, ±1mA, 0-20mA and 4-20mA current outputs.
Using PAS
the Analog Outputs tab.
Figure ‎5-10: General Setup Dialog Box – Analog Outputs Tab

The available analog output options are described in Table 13.

Table 13: Analog Output Options
Option Range Description
AO type 0-1mA The analog output type. When connected
±1mA to the meter, shows the actual AO type
0-20mA received from the device. When working
4-20mA off-line, select the analog output option
corresponding to your analog module.
Output parameter See Appendix B Selects the measured parameter to be
transmitted through the analog output
channel.
Zero scale Defines the low engineering scale (in
primary units) for the analog output
corresponding to a lowest (zero) output
current (0 or 4 mA)
Full scale Defines the high engineering scale (in
primary units) for the analog output
corresponding to a highest output current
(1 or 20 mA)
When you select an output parameter for the analog output channel,
the default engineering scales are set automatically. They correspond
to the maximum available scales. If the parameter actually covers a
lower range, you can change the scales to provide a better resolution
on an analog output.
Scaling Non-Directional Analog Outputs
For non-directional analog outputs with a 0-1mA, 0-20mA or 4-20mA

current option, you can change both zero and full engineering scales
for any parameter. The engineering scale need not be symmetrical.
Scaling Directional Power Factor
The engineering scale for the signed power factor emulates analog
power factor meters.
The power factor scale is -0 to +0 and is symmetrical with regard to

1.000 (-1.000  +1.000). The negative power factor is scaled as
-1.000 minus the measured value, and non-negative power factor is
scaled as +1.000 minus the measured value. To define the entire
power factor range from -0 to +0, the default scales are specified as -
0.000 to 0.000.
Scaling ±1mA Analog Outputs
Programming engineering scales for directional ±1mA analog outputs

depends on whether the output parameter represents unsigned (as
volts and amps) or signed (as powers and power factor) values.
For an unsigned output value, you can change both zero and full
engineering scales.
For a signed (directional) value, you should only provide the

engineering scale for the +1 mA output current.
The engineering scale for the 0 mA output current is always equal to

zero for all values except the signed power factor, for which it is set to
1.000 (see Scaling Directional Power Factor above).

The meter does not allow access to the low scale setting if the
parameter is directional. Whenever the sign of the output parameter is
changed to negative, the meter automatically uses the full engineering
scale setting for +1 mA with a negative sign.
Scaling Analog Outputs for 0-2 mA and ±2 mA
The 0-1mA and ±1mA current outputs provide a 100% overload, and
actually output currents up to 2 mA and ±2mA whenever the output
value exceeds the engineering scale you set for the 1 mA or ±1mA.
The output scales for 0-1 mA and ±1 mA analog outputs are

programmed for 0 mA and +1 mA regardless of the required output
current range.
To use the entire output range of 2 mA or ±2 mA, set the analog

output scales as follows:
 0-2 mA: set the 1 mA scale to ½ of the required full scale output for
uni-directional parameters, and set the 0 mA scale to the negative
full scale and the 1 mA scale to zero for bi-directional parameters.
 ±2 mA: set the 1 mA scale to ½ of the required full-scale output for

both uni-directional and bi-directional parameters.
For example, to provide the 0 to 2 mA output current range for Volts

measured by the meter in the range of 0 to 120V, set the 1 mA scale
to 60V; then the 120V reading will be scaled to 2 mA.
Configuring Counters
The EM13X Series has four six-digit general counters that can count
pulses delivered through the device digital inputs with a programmable
scale factor. Each counter can also be incremented in response to any
internal or external event, checked and cleared through the Control
Setpoints.
Using PAS
the Pulse/Event Counters tab.

Figure ‎5-11: General Setup Dialog Box – Pulse/Event Counters
Table 14 lists available counter options.

Table 14: Counter Options
Option Range Default Description
Pulse Input None, None Links a digital input to the
DI1 counter
DI2
DI3
DI4
DI5
DI6
DI7
---
DI14
Multiplier 1-9999 1 The value added to the counter
when a pulse is detected on the
pulse source input
Counter Value Displays the present counter
contents
You can preset a counter to a required value or clear it without

affecting the counter setup.
To preset or clear a counter:
 Click the Online button on the PAS toolbar before accessing the setup
dialog box.
 Type in the required value into the Counter Value field
 Click Send

Configuring Alarm/Control Setpoints

The EM13X Series has an embedded logical controller that can perform
different actions in response to user-defined internal and external
events. Unlike a PLC, the meter uses a simplified programming
technique based on setpoints that allows the user to define a logical
expression based on measured analog and digital values that produce
a required action.
The meter provides 16 control setpoints with programmable operate

and release delays. Each setpoint evaluates a logical expression with
one trigger argument. Whenever an expression is evaluated as “true”,
the setpoint performs a programmable action that can send a
command to the output relay, or increment a counter.
The logical controller provides very fast response to events. The scan
time for all setpoints is 1 cycle time (16.6 ms at 60Hz and 20 ms at
50/400 Hz).
Using PAS
the Control/Alarm Setpoints tab.
Figure ‎5-12: General Setup Dialog Box – Control/Alarm Setpoints Tab

The following table lists the available setpoint options.

Table 15: Setpoint Options
Trigger See Appendix C The trigger parameter that is used as an
parameter argument in the logical expression
Operate limit The threshold (in primary units) at which
the conditional expression would be
evaluated to true. Not applicable for digital
triggers.
Release limit The threshold (in primary units) at which
the conditional expression would be
evaluated to false. Defines the hysteresis
for analog triggers. Not applicable for
digital triggers.
Operate delay 0.1-999.9 sec The time delay before operation when the
operate conditions are fulfilled
Release delay 0.1-999.9 sec The time delay before release when the
release conditions are fulfilled
Action See Appendix C The action performed when the setpoint
expression is evaluated to true (the
setpoint is in operated state)
Using Numeric Triggers
For numeric (analog) triggers, you can specify two thresholds for each
trigger to provide hysteresis (dead band) for setpoint operations.
The Operate Limit defines the operating threshold, and the second
Release Limit defines the release threshold for the trigger. The trigger
thresholds are specified in primary units.
If you do not want to use hysteresis for the trigger, set the Release
Limit to the same value as the Operate Limit.
Using Binary Triggers
Binary (digital) triggers like digital inputs and relays are tested for
ON/CLOSED or OFF/OPEN status.
In the PM130, the binary events are level-sensitive events. An event is

asserted all the time while the corresponding condition exists.
Delaying Setpoint Operations
Two optional delays can be added to each setpoint to extend

monitoring triggers for a longer time before reaching a decision on
whether the expected event occurred or not. When a delay is specified,
the logical controller changes the setpoint status only if all conditions
are asserted for a period of at least as long as the delay time.
Using Setpoint Events and Actions
When a setpoint status changes, i.e., a setpoint event is either

asserted or de-asserted, the following happens in your meter:
 The new setpoint status is logged to the setpoint status register that
can be monitored through communications from the SCADA system
or from a programmable controller in order to give an indication on
the expected event.
 The operated setpoint status is latched to the setpoint alarm latch

register that can be inspected through communications and via the
display (see Status Display in Chapter 3). The register holds the last

setpoint alarm status until it is explicitly cleared through

communications or via the display.
 A programmable action is performed on setpoint status transition

when a setpoint event is asserted.
Generally, setpoint actions are performed independently for each

setpoint and can be repeated a number of times for the same target.
The exceptions are relay operations that are shared for each target
relay between all setpoints using an OR scheme.
A relay output is operated when one of the setpoints linked to the relay
is activated and remains operated until all of these setpoints are
released (except for latched relays that require a separate release
command to be deactivated).
Using Time Counters
Any of the general counters can be used to count the setpoint

operation time. If you select the TIME CNT n action for a setpoint, the
target counter measures the time while the setpoint is in the operated
state. The counter resolution is 0.1 hour. See Status Display in Chapter
3 on how to examine the counters via the front display.

Configuring the Display

This setup allows configuring the meter display. It also has an entry for
launching the meter Flash Loader.
Select the Disp entry from the main menu. See Viewing and Changing
Setup Options in Chapter 3 for information on configuring parameters
Disp AutoScroll via the front display.
5
See Table 16 for the available options.
Table 16: Display Setup Options

Label
AutuoScroll Display update Disabled 5 sec Defines the interval
rate 2 – 30sec between display updates
AutoReturn Auto return to Disabled, 5 mn Enables automatic return to
the main screen 1 – 30 mn the main display if no
buttons are pressed for 5
minutes
Backlight Display Continuous, 1 Defines the display
Backlight period 1 – 10 mn backlight light on time
duration
Phas.Power Phase powers Enabled Disabled Disables or enables phase
display mode Disabled powers in the main display
Fund.Power Fundamental Enabled Disabled Disables or enables
component Disabled fundamental values in the
display mode main display

Using PAS
the Display Setup tab.
Figure ‎5-13: General Setup Dialog Box – Display Setup Tab
The available options are listed in the table 17 below.
See Display Operations in Chapter 3 for more information on display

functionality and configuring display options. See Data Displays for
information on display page contents and enumeration.

Table 17: Display Setup Options

Display Label Parameter Options Default Description
Auto-Scroll Auto-Scroll Disabled, 5 Defines the display
Interval 2-10, 15, 20, scroll interval or
25, 30 seconds disables auto-scroll
Scroll Seq. Auto-Scroll 1 1 Selects the display
Sequence 1-2 to 1-7 sequence for auto-
1, 5 scrolling from 9
1, 5-6, data displays (see
1, 5-7, Data Displays for
1-2, 5-7 display
1-3, 5-7 enumeration)
1, 6-7
1-2, 6-7
1-3, 6-7
1-4, 6-7
1, 7
1-2, 7
1-3, 7
1-4, 7
1-5, 7
3
3-4
3-5
3-6
3-7
3, 5
3, 5-6
3, 5-7
3, 7
5
5-6
5-7
5,7
Auto-Return Auto-Return Disabled, 5 Defines the time
1-5, 10, 15, 20, delay before
25, 30 min returning to the
default page
Backlight Backlight Time Continuous, 1 Defines the time
1-10 min while the backlight
is ON
Phase Power Phase powers Enabled Disabled Disables or enables
display mode Disabled phase powers in the
main display
Fundamental Power Fundamental Enabled Disabled Disables or enables
component Disabled fundamental values
display mode in the main display
Local Time Settings

This setup allows you to specify your time zone, daylight saving time,
and clock synchronization options.
Select Local from the main menu. See Viewing and Changing Setup
Locak Exit Options in Chapter 3 for information on configuring parameters via the
front display.
Using PAS
the Local Settings tab.

Figure ‎5-14: General Setup Dialog Box – Local Settings Tab
The available options are described in Table 18.

Table 18: Local Time Options
Label
Date Order Day/month/year DD/MM/YY DD/MM/YY Defines date order
order MM/DD/YY presentation
YY/MM/DD
Country Country code Default, or country Default Defines calendar setting.
name The default setting stands
for the U.S.A.
Daylight Daylight Saving Disabled Disabled When DST is disabled, the
Time Enabled RTC operates in standard
time only. When enabled,
the meter automatically
updates the time at the pre-
defined DST switch dates.
Start Mon DST Start Month January to December March The month when Daylight
Saving Time begins.
Start Week DST Start Week 1st to 4th and last Second The 2nd week of the month
when Daylight Saving Time
begins.
Start Day DST Start Day The weekday Sunday The 2nd Sunday of the
month when Daylight
Saving Time begins.
Start Hour DST Start Hour 1-6 2 The hour when Daylight
Saving Time begins.
dSt.E DST End Month-week-weekday First Sunday The date when Daylight
Weekday Week = 1, 2, 3, 4 or L in November Saving Time ends.
(last week of the month)
End Mon DST End Month January to December November The month when Daylight
Saving Time ends.

‎Chapter 5 Configuring the EM13X Series Configuring Meter Security

Label
End Week DST End Week 1st to 4th and last First The 1st week of the month
when Daylight Saving Time
ends.
End Day DST End Day The weekday Sunday The 1st Sunday of the
month when Daylight
Saving Time ends.
End Hour DST End Hour 1-6 2 The hour when Daylight
Saving Time ends.
Clock Sync Time None None The external port receiving
Synchronization DI1 1PPM the time synchronization
Input DI2 1PPM pulses
DI3 1PPM
DI4 1PPM
DI5 1PPM
DI6 1PPM
DI7 1PPM
…
DI14 1PPM
Daylight Saving Time
When the daylight saving time is enabled, the meter automatically

advances the device clock by one hour when daylight saving time
begins and puts the clock back one hour when it ends. The default
daylight saving time change points are preset for the U.S.A.
The daylight saving time option is disabled in the PM130 by default. If

the daylight saving time option is disabled, you need to manually
adjust the device clock for daylight saving time.
Time Synchronization Pulses
External time synchronization pulses can be delivered through one of

the digital inputs.
If a digital input is selected as the time synchronization source, the

edge of an external pulse adjusts the device clock at the nearest whole
minute. The time accuracy could be affected by the debounce time of
the digital input, and by the operation delay of the external relay.
5.3 Configuring Meter Security

This setup allows changing the user password and enabling or disabling
password protection. The EM13X Series provides 3 configurable
passwords.
The password in your meter is preset to 0 at the factory, and password

protection is disabled.
Select the Access entry from the main menu. See Viewing and
Changing Setup Options in Chapter 3 for information on configuring
parameters via the front display.

‎Chapter 5 Configuring the EM13X Series Configuring Meter Security
To change the password:
Access Passwrd 1  Apply LONG PRESS on ENTER button to select the Passwrd 1 entry
9  Apply SHORT PRESS on ENTER button to select the password digit to
change.
LONG PRESS
 Apply LONG PRESS on ENTER button to exit the Passwrd 1 digit field
Access Passwrd 1
00000009  Apply LONG PRESS on ENTER button to exit the Passwrd 1 field to
move to Access field
SHORT PRESS
The new password is effective for both the display and

communication ports.
Using PAS
Ensure that the On-line button on the PAS toolbar is checked, select
Administration from the Monitor menu, and then select Change
Password -> Password 1.
An Authorization Required dialog box will ask for administrator

password to access the Change Password menu.
Figure ‎5-15: Password Setup Dialog Box
To change the password:

 Type in a new 8-digit password
 Repeat the password in the Confirm new password box
 Click Send

‎Chapter 5 Configuring the EM13X Series Configuring Billing/TOU
5.4 Configuring Billing/TOU

Billing Energy Registers
The EM13X Series has 4 fully programmable billing energy registers

that can be linked to any internal energy source or to an external pulse
source that delivers pulses through the meter digital inputs.
Any energy register can provide either a single-tariff energy

accumulation or be individually linked to the TOU system providing
both total and multi-tariff energy billing.
Tariff Rates
The meter tariff structure supports 8 different tariff rates using an

arbitrary tariff schedule. A total of 4 types of days and 4 seasons are
supported with up to eight tariff changes per day.
Maximum Demand Registers
Any of billing energy registers can be individually linked to the

maximum demand register providing the same demand tariff structure
as you selected for energy registers.
Recording Billing Data and Load Profiling
The EM13X Series can provide automatic recording of the daily energy
and maximum demand profile to a data log file. Maximum demand
profiling can be individually configured for every register.
See Factory Preset Data Log Files in Chapter 5 and Billing Profile Log
File in Appendix E for more information on the file layout and contents.
To configure the billing registers and the tariff system in your meter:
 Link the billing registers to the respective energy sources.
 Configure the options for the registers to whether the only totalization or
both total and tariff registers would be used, and whether daily profiling
should be enabled for the energy usage and maximum demand
registers.
 Configure the daily tariff schedule using the TOU daily profiles for all
types of days and seasons.
 Configure the season tariff schedule using the TOU calendar.
Configuring Billing/Tariff Registers

To configure the billing/TOU registers in your meter:
 Select Energy/TOU from the Meter Setup menu.

Figure ‎5-16: Energy/TOU Setup Dialog Box – Billing/TOU Registers tab
 Configure the register options according to the valid parameters shown

in Table 19.
Table 19: Billing/TOU Register Options

Billing/TOU Registers
TOU Unchecked Unchecked Links tariff registers to the selected energy
Checked source
Use Profile Unchecked Checked Enables recording energy registers in a daily
Checked billing profile file (both total and tariff
registers if TOU is enabled).
Dmd Profile Unchecked Unchecked Enables recording maximum demand
Checked registers in a daily billing profile file (both
total and tariff registers if TOU is enabled)
Sum Profile Unchecked Checked Enables recording total (summary) registers
Checked in a daily billing profile file.
Units kWh, kvarh, kVAh, None The register measurement units. When a
m3, CF (cubic register is linked to an internal energy
foot), CCF source, it is set automatically. When an
(hundred cubic external pulse source is used, the user can
feet) select a measurement unit for the register.
Register Source List
Source Input None None Links an energy source to the register
kWh Import
kWh Export
kvarh Import
kvarh Export
kvarh Q1-Q4
kVAh Total
kVAh Import
kVAh Export
kWh L1 Import
kWh L2 Import
kWh L3 Import
DI1-DI14
Multiplier 0.001 to 100.000 1.000 The multiplication factor for the energy
source. Unchangeable for internal energy
sources.
Target Reg#1- Reg#4 None Defines the target billing register for the
energy source. It is set automatically.

Configuring the Daily Tariff Schedule

To configure your daily tariff schedule, select Energy/TOU from the
Meter Setup menu, and then click on the TOU Daily Profiles tab.
Figure ‎5-17: Energy/TOU Setup Dialog Box – TOU Daily Profiles Tab
The daily profile setup allows you to specify the daily tariff change
points with a 15-minute resolution for 4 seasons using 4 different daily
schedules for each season.
To configure your daily profiles:
 Select the desired season and day type.
 Select the start time for each tariff change point and the corresponding
active tariff number.
 Repeat the setup for all active profiles.
 The first tariff change point is fixed at 00:00 hours, and the last tariff
change you specified will be in use until 00:00 hours on the next day.
NOTE
The billing daily profile log file is automatically configured for the
number of active tariffs you defined in the meter TOU daily profiles.

Configuring the Season Tariff Schedule

To configure your season tariff schedule, select Energy/TOU from the
Meter Setup menu, and then click on the TOU Calendar tab.
Figure ‎5-18: TOU Calendar Setup Dialog Box – TOU Calendar Tab
The meter TOU calendar allows you to configure any tariff schedule
based on any possible utility regulation. The calendar provides 32
entries that allow you to specify profiles for working days and holidays
through all seasons in any order that is convenient for you, based on
simple intuitive rules.
To configure your season tariff schedule:
In the Season/Period box, select the season, and in the Day Type
box, select a day type for this calendar entry.
Define the time interval when this daily tariff schedule is effective,
based on the start and end weekdays and, for a multi-season schedule,
on the start and end month for the selected season. It does not matter
which order of weekdays or months you select: the meter recognizes
the correct order.
For exception days like weekends and designated holidays, define a
specific day either by a month and a month day, or by selecting a
month, a week and a weekday within the month.
There are no limitations on how to build your schedule. A common

recommendation is to use minimum time constraints and only when it
is needed to avoid ambiguity. You need not to define month days if a
daily schedule is effective all days of the month, or to define the start
and end months if it is effective through all the year. If you wish to
define a specific period within a month using the start and end days,
put this entry before allocating the remaining days to another daily
schedule without specified month days, so it would be checked first for
a match.
The above picture shows a typical single-season tariff schedule with

two daily tariff profiles configured for working days, and weekends and
the designated U.S.A. holidays.

‎Chapter 5 Configuring the EM13X Series Configuring Recorders
5.5 Configuring Recorders

The EM13X Series has a 125-KByte onboard non-volatile memory for
data and event recording. The memory is fully configurable and can be
freely partitioned between log files.
The meter provides memory for a total of 3 log files:
 Event log
 Two data logs
The two data log files are pre-configured at the factory for recording a
15-minute energy and demand profile and for the daily billing energy
data profile. If you wish to change the factory settings, follow the
guidelines in the next section.
Configuring Meter Memory

To view the present memory settings, select Memory/Log from the
Meter Setup menu, and then click on the Log Memory tab.
Figure ‎5-19: Log Setup Dialog Box – Log Memory Tab
The following table describes file options.

Type Wrap- Wrap-around: recording continues over the oldest
around records.
Non-wrap Non-wrap: recording is stopped until the file is
cleared.
Size The size of memory allocated to the file.
Sections/Channels 0-8 The numbers of sections in a multi-section profile
data log file
Num. of Records 0-65535 Allocates the file memory for predefined number of
records
Record size The size of the file record for a single channel or a
single section. It is set automatically depending on
the file and on the number of parameters in the
data records
Parameters 0-9 The number of parameters in a single data log
record

To change the file properties or to create a new file:

 Double click on the file you want to change.
 Select desired parameters for your log.

 Click OK.
For your reference, the record size and the number of records available
for your file are reported in the dialog box.
To delete an existing file partition:
 Click on Delete.
 Click OK.
NOTES
 Memory is allocated for a file statically when you set up your files and
will not change unless you re-organize files.
 The meter automatically performs de-fragmentation of the memory each
time you re-organize your files. This prevents possible leakage of
memory caused by fragmentation. It may take a couple of seconds.
For more information on configuring specific files, see the following

sections.
The following table can help you calculate an estimated file size when
planning your memory allocation.
File Record Size, Bytes File Size, Bytes

Event Log 16 Record size  Number of records
Conventional data Log 12 + 4  Number of parameters Record size  Number of records
Billing/TOU daily 12 + 4  (Number of season tariffs + 1 Record size  Number of billing registers
profile log for the TOU summary/total register) ( 2 for the maximum demand profile) x
Number of records
The factory pre-set file configuration is shown in the following table.

No. File Size, Channels Number of Number Factory-set Configuration
Bytes Records of Events
1 Event log 3200 200 200 200 last events
2 Data log #1 46080 5760 5760 15-min data profile for 15 days
17 Data log #16 8640 4 90 90 Daily billing/TOU profile for 90
days, 4 registers, totals + 3 tariffs

Configuring the Event Recorder

To configure the Event log file:
Double click on the Event Log file partition with the left mouse button.
Select a desired file type for your file.

Select the maximum number of records you want to be recorded in the
file.
Click OK, then send your new setup to the meter or save to the device
database.
By default, the Event recorder stores all events related to configuration

changes, resets, and device diagnostics.
Configuring the Data Recorder

Conventional Data Log Files
The Data recorder is programmable for recording up to 9 data

parameters per record in each of the conventional data log files. The
list of parameters to be recorded to a data log is configurable
individually for each file.
To create a new data log file or re-configure an existing file:

Double click on the file partition with the left mouse button.
Select a partition type for your file.

Select the number of parameters you want to be recorded in the file
records.
file.

Click OK, and then send your new setup to the meter, or save to the
device database.
To define the contents of the file:

Highlight the data log file row with the left mouse button, and then
click on the Setup Recorder button, or click on the Data Recorder
tab and select the corresponding log number.
Figure ‎5-20: Log Setup Dialog Box – Data Recorder Tab
Configure the list of parameters to be recorded in a log file. You are

not allowed to select more parameters than you defined when
configuring your file. Refer to Appendix D for a list of available
parameters.
For your convenience, PAS follows your selection and helps you
configure a series of the neighboring parameters: when you open the
Group box for the next parameter, PAS highlights the same group as
in your previous selection; if you select this group again, PAS
automatically updates the Parameter box with the following
parameter in the group.
Add the name for your data log file in the Name box. It will appear in
the data log reports.
Save your new setup to the device database, and send it to the meter.
Billing/TOU Daily Profile Log File
Data log #16 is configurable to store TOU daily profile log records on a
daily basis.
The file is organized as a multi-section file that has a separate section

of the same structure for each billing energy and maximum demand
register. The number of sections is taken automatically from the
Billing/TOU Registers setup (see Configuring Billing/Tariff Registers). If the
maximum demand profiling is used, then the number of sections in the
file will be twice the number of the allocated billing registers.
To configure a daily profile log file:
Configure your Billing/TOU registers and tariff schedule in the meter

(see Configuring Billing/Tariff Registers) first.

Double click on the Data Log#16partition with the left mouse button.
Select the TOU Daily Profile file type.
Select the number of season tariffs in your TOU schedule. Add one
additional parameter if you selected to record the Summary (TOU
total) registers as well.

file assuming that a new record will be added once a day.
Click OK and send your setup to the meter or save to the meter
database.
Factory Preset Data Log Files

Conventional Data Log #1
Data log #1 is factory preset for 15-min periodic recording of the

standard energy and demand quantities. You can freely change the list
of recorded parameters and the file update rate.
The default list of parameters is shown in the following table.

No. Parameter
1 kWh import
2 kWh export
3 kW import sliding demand
4 V1 demand
5 V2 demand
6 V3 demand
Periodic recording data is triggered by Setpoint #1 that is linked to the

meter clock. To change the periodic rate at which data is recorded,
change the time interval for the MINUTE INTERVAL trigger in Setpoint
#1 (see Configuring Alarm/Control Setpoints).
Billing/TOU Profile Data Log #16
Data log #16 is pre-configured for daily billing energy and maximum
demand recording for the last 90 days. It is automatically updated
once a day.
See Billing Profile Log File in Appendix E for the file record structure.

‎Chapter 5 Configuring the EM13X Series Configuring Communication Protocols
5.6 Configuring Communication Protocols

This section describes how to customize protocol options for use with
your application software.
Configuring Modbus
Modbus Point Mapping
The EM13X Series provides 120 user assignable registers at addresses

0 to 119. You can re-map any register available in the meter to any
assignable register so that registers found at different locations may be
accessed with a single request by re-mapping them to adjacent
addresses.
Initially these registers are reserved and none of them points to an

actual data register. To build your Modbus register map:
Select Protocol Setup from the Meter Setup menu, and click on the
Modbus Registers tab.
Click on the Default button to cause the assignable registers to
reference the actual default meter register 6656 (0 through 119 are
not allowable register addresses for re-mapping).
Figure ‎5-21 : Protocol Setup Dialog Box – MODBUS Registers Tab
Type in the actual addresses you want to read from or write to via the
assignable registers. Refer to the PM130 PLUS Modbus Reference Guide
for a list of the available registers. Note that 32-bit Modbus registers
should always start at an even register address.
Click Send to download your setup to the meter.

Changing 32-bit Register Format
The EM13X Series allows you to read 32-bit Modbus analog registers,
energy counters and binary counters either in integer format, or in
IEEE single precision floating point format.
The 32-bit MODBUS registers are factory-set to integer format. To

change the register format:
Select Protocol Setup from the Meter Setup menu, and click on the
Modbus Registers tab.
Change the 32-bit register format in the MODBUS Options pane.
Configuring DNP3
Refer to the EM13X Series DNP3 Reference guide for information on
the DNP3 protocol implementation and a list of the available data
points.
DNP Options
Select Protocol Setup from the Meter Setup menu and click on the
DNP Options tab.
Figure ‎5-22: Protocol Setup Dialog Box – DNP Options Tab
The following table describes available options. Refer to the DNP3 Data
Object Library document available from the DNP User’s Group on the
DNP3 object types.

Table 20: DNP Options

Binary Inputs (BI)
Binary Input Object Single-bit Single-bit The default BI object variation for
With Status requests with qualifier code 06 when no
specific variation is requested
Analog Inputs (AI)
Analog Input Object 32-bit 16-bit-Flag The default AI object variation for
32-bit–Flag requests with qualifier code 06 when no
16-bit specific variation is requested
16-bit–Flag
Binary Counters (BC)
Binary Counter Object 32-bit+Flag 32-bit-Flag The default BC object variation for
32-bit–Flag requests with qualifier code 06 when no
16-bit+Flag specific variation is requested
16-bit–Flag
DNP General Options
16-bit AI Scaling Disabled Enabled Allows scaling 16-bit analog input
Enabled objects (see description below)
16-bit BC Scaling x1, x10, x1 Allows scaling 16-bit binary counter
x100, x1000 objects (see description below)
1
SBO Timeout 2-30 sec 10 Defines the Select Before Operate (SBO)
timeout when using the Control-Relay-
Output-Block object
2
Time Sync Period 0-86400 sec 86400 Defines the time interval between
periodic time synchronization requests
Multi Fragment 50-500 ms 50 Defines the time interval between
Interval fragments of the response message
when it is fragmented
Scaling 16-bit AI objects
Scaling 16-bit AI objects allows accommodating native 32-bit analog

input readings to 16-bit object format; otherwise it may cause an over-
range error if the full-range value exceeds a 16-bit point limit.
Scaling is enabled by default. It is not related to points that are read

using 32-bit AI objects.
Refer to the PM130 DNP3 Reference Guide for information on the data
point scales and a reverse conversion that should be applied to the
received scaled values.
Scaling 16-bit Binary Counters
Scaling 16-bit Binary Counters allows changing a counter unit in

powers of 10 to accommodate a 32-bit counter value to 16-bit BC
object format.
1
The Select Before Operate command causes the meter to start a timer. The
following Operate command must be sent before the specified timeout value
expires.
2
The meter requests time synchronization by bit 4 in the first octet of the
internal indication word being set to 1 when the time interval specified by the
Time Sync Period elapses. The master should synchronize the time in the meter
by sending the Time and Date object to clear this bit. The meter does not send
time synchronization requests if the Time Sync Period is set to 0.

If the scaling unit is greater than 1, the counter value is reported being
divided by the selected scaling unit from 10 to 1000. To get the actual
value, multiply the counter reading by the scaling unit.
Configuring DNP Class 0 Responses
The most common method of getting static object information from the
meter via DNP is to issue a read Class 0 request. The EM13X Series
allows you to configure the Class 0 response by assigning ranges of
points to be polled via Class 0 requests.
To view or build a DNP Class 0 response message:
Select Protocol Setup from the Meter Setup menu and click on the
DNP Class 0 Points tab.
Select the object and variation type for a point range.
Specify the start point index and the number of points in the range.
Refer to the EM13X Series DNP3 Reference Guide for available data
points.
Repeat these steps for all point ranges you want to be included into the
Class 0 response.
The factory-set Class 0 point ranges are shown in the picture below.
Figure ‎5-23: Protocol Setup Dialog Box – DNP Class 0 Points Tab

‎Chapter 6 Device Control and Upgrading Resetting Accumulators, Maximum Values and Files
Chapter 6 Device Control and

Upgrading
This section describes operations on the meter you can perform from
the front display or via PAS. To access device control options from PAS,
you should have your meter online.
6.1 Resetting Accumulators, Maximum Values and Files

Select the RESET entry from the main menu. See Viewing and
Changing Setup Options in Chapter 3 for information on configuring
parameters via the front display.
To reset the desired values:
Highlight the middle window by pressing briefly the SELECT button.
Select a reset entry by scrolling through the list with the UP and
DOWN arrow buttons.
Press the SELECT button briefly to highlight the lower item.
Press and hold the ENTER button for 5 seconds.
Release the button.
The do entry is replaced with done showing the operation is complete.
Table 21 shows the reset options available from the front display.
Table 21: Front Display Reset Options

Display Label Description
Power Dmd Clears power maximum demands
V/A Dmd Clears ampere and volt maximum demands
Min/Max Clears Min/Max log
Counters Clears all counters
Counter 1 – Counter 4 Clears counter #1-#4
Diagnostics Clears device diagnostics
Using PAS
Ensure that the On-line button on the PAS toolbar is checked, and
then select Reset from the Monitor menu.

‎Chapter 6 Device Control and Upgrading Resetting Accumulators, Maximum Values and Files
Figure ‎6-1: Reset Dialog
To reset the desired values or files:

Click on the corresponding button, and then confirm your command.
If an entry has more than one target, you are allowed to select targets
to reset.
Check the corresponding boxes, and then click OK.
Figure ‎6-2: Reset Maximum Demands Dialog Box

‎Chapter 6 Device Control and Upgrading Updating the Meter Clock
6.2 Updating the Meter Clock

Select the RTC entry from the main menu.

To change the time or date:
Reset Exit
When in RTC setup menu, applying a LONG PRESS on the
SCROLL until SELECT/ENTER button will display the Time/Date screen while Time
RTC menu
RTC Exit willflash. Another LONG PRESS on SELECT/ENTER button will
flash the actual hour to be changed using SCROLL button

LONG PRESS
RTC Oct 23,2011

Time 15:03:16
LONG PRESS
RTC Oct 23,2011

Time 15:03:16
SHORT PRESS
Moves to Date
Table 22 describes available options.
Table 22: Clock Setup Options

Display Parameter Options Description
Label
Time Time Hh:mm:ss Hours, minutes and seconds are
separated by ":". The time is displayed as
hh:mm:ss.
Month Date Mon XX, Year Month/Day Date and year are separated
name by",". Where the first three letters
represent the month, then the day of the
months is represented by two digits and
finally the year presented by 4 digits
Using PAS
then select RTC from the Monitor menu or click on the Real-Time
Clock button on the PAS toolbar.
The RTC dialog box displays the current PC time and the time in your
meter.
Figure ‎6-3: Real Time Clock Window
To synchronize the meter clock with the PC clock, click Set.

‎Chapter 6 Device Control and Upgrading Viewing and Clearing Device Diagnostics
6.3 Viewing and Clearing Device Diagnostics

See Diagnostics Display in Chapter 3 on how to view and clear device

diagnostics from the front display.
Using PAS
Device Control from the Monitor menu, and then click on the Device
Diagnostics tab.
See Device Diagnostic Codes in Appendix G for the list of diagnostic

codes and their meaning.
Figure ‎6-4: Device Control Dialog Box – Device Diagnostics Tab
To clear the device diagnostics events, click on Clear.
6.4 Viewing Communication Status and Statistics

Device Control from the Monitor menu, and then click on the
Communications tab.

‎Chapter 6 Device Control and Upgrading Remote Relay Control
Figure ‎6-5: Device Control Dialog Box – Communications Tab
This window indicates the present GPRS communication status (see

Setting Up GPRS Network in Chapter 5) and connection statistics of the
TCP clients (see Setting Up eXpertPower Client and Setting Up TCP
Notification Client in Chapter 5).
To clear the communication counters, click on Clear.
You can also clear the communications counters via the PAS Reset
dialog (see Resetting Accumulators, Maximum Values and Files).
6.5 Remote Relay Control

You can use PAS to send a remote command to your meter to operate any
relay output or release a latched relay, except of the relays linked to an
internal pulse source. These relays are blocked for operating from outside
of the meter.
To access the relay control dialog, ensure that the On-line button on the
PAS toolbar is checked, select Device Control from the Monitor menu,
and then click on the Remote Relay Control tab.

‎Chapter 6 Device Control and Upgrading Upgrading Device Firmware
Figure ‎6-6: Device Control Dialog Box – Remote Relay Control Tab
To send a remote command to a relay:

Select a desired command in the Relay Command box for a relay:
OPERATE – to operate a relay
RELEASE – to remove your remote command, or to release a latched
relay
Click Send.
6.6 Upgrading Device Firmware

Your meter has upgradeable firmware. If you need to upgrade your
device, download a new firmware file to the meter through PAS.
Firmware can be downloaded via the MODBUS RTU or MODBUS/TCP

protocol through any communication port.
To download a new firmware file to your device:
Ensure that the communication port you are connected through to the
meter operates in Modbus mode.
If you are connected to the meter through a serial interface, it is
recommended to set the port baud rate to 115,200 bps. See Setting
Up Serial Communication Ports on how to remotely change the protocol
and baud rate in your meter.
then select Flash Downloader from the Monitor menu and confirm
downloading.
Point to the firmware upgrade file for your meter, click Open, and then
confirm upgrading the meter.

‎Chapter 6 Device Control and Upgrading Upgrading Device Firmware
You are asked for the password regardless of the password protection
setting in your meter. Type the meter password, and click OK. If you
did not change the password in the meter, enter the default password
0.
Wait until PAS completes upgrading your device. It takes about 3-4
minutes at 115,200 bps to download the file to the meter.
After upgrading firmware is completed, the meter restarts, so

communications can be temporarily lost. You may need to wait a short
duration until PAS restores a connection with your device.

‎Chapter 7 Monitoring Meters Viewing Real-time Data
Chapter 7 Monitoring Meters

7.1 Viewing Real-time Data
Real-time data can be continuously retrieved from your devices and
updated on the screen at the rate you defined in the Instrument Setup.
To get real-time data from your meter:

Ensure that the On-line button on the PAS toolbar is checked.
Select the device site from the list box on the PAS toolbar.
Point to RT Data Monitor on the Monitor menu, and then select a
data set you want to view.
Polling Devices
Click on the “Poll” or “Continuous poll” button to poll the meter

once or continuously.
Click on the Stop button to stop continuous polling.

The following picture shows a typical data monitor window.
Figure ‎7-1: RT Data Monitor Window
You can open as many monitor windows as you wish, either for
different sites, or for the same site using different data sets. An open
data monitor window is linked to the current site and does not change
if you select another site in the site list.
You can view acquired data in a tabular form or in a graphical form as

a data trend.

‎Chapter 7 Monitoring Meters Viewing Real-time Data
Organizing Data Sets
PAS supports 33 programmable data sets with up to 40 data

parameters. Set #0 is intended for simple meters, which have a limited
number of parameters, and is not recommended for the use with the
EM13X Series. To re-organize data sets, select RT Data Sets from the
Monitor menu or click on the button on the local toolbar.
Some data sets are preset for your convenience and others are empty.
You can freely modify data sets.
See Appendix D for a list of data available in your meter.
Polling Options
To change the polling options, click on the Data Monitor window with
the right mouse button and select Options.
If you check Do not stop on errors, polling is resumed automatically

when a communication error occurs, otherwise polling stops until you
restart it manually.
Viewing a Data Table

Changing the Data View
PAS displays data in either a single record or multi-record view. To

change the view, click on the Data Monitor window with the right
mouse button and select either Wrap to see a single record, or
UnWrap to go to the multi-record view.
Adjusting the Number of Rows in a Multi-Record View
Click the window with the right mouse button, select Options, adjust
the number of records you want to see in the window, and then click
OK. When the number of retrieved records exceeds the number of rows
in the window, the window scrolls up so that older records are erased.

‎Chapter 7 Monitoring Meters Viewing Real-time Min/Max Log
See Working with Tables in Chapter 9 for more information on working

with tables.
Viewing Data Trend
To view a data trend, click on the button on the local toolbar.
To change the time range for your graph, click on the button on the
local toolbar, and then select the desired date and time range.
See Working with Graphic Windows in Chapter 9 for more information

on working with graphs.
Saving Data to a File
To save retrieved data to a file for later analysis, click on the Save
button , select an existing database or type the name for a new
database, and then click Save.
To avoid confusion, do not store data files into the Sites directory
where site databases are located.
Printing Data
To check the report, as it will look when printed, select Print Preview
from the File menu.
To print retrieved data, click on the buttonon the PAS toolbar,

select a printer, and then click OK.
Real-time Data Logging
PAS allows you to store data records to a database automatically at the

time it updates data on the screen.
To setup the real-time logging options:

Open the Data Monitor window.
Click on the RT Logging On/Off button on the local toolbar, or

select RT Logging Options from the Monitor menu.
Select a database, or type the name for a new database and select a
directory where you want to save it.
Select the number of tables, and the number of records in each table
you want recorded.
Adjust the file update rate for automatic recording. It must be a
multiple of the sampling rate that you defined in the Instrument Setup
dialog.
Click Save.
When you run real-time data polling, PAS automatically saves retrieved
records to a database at the rate you specified.
The RT Logging On/Off button on the toolbar should be checked

all the time. You can suspend logging by un-checking the button, and
then resume logging by checking it again.

‎Chapter 7 Monitoring Meters Viewing Real-time Min/Max Log
7.2 Viewing Real-time Min/Max Log

To retrieve the real-time Min/Max log data from your meter:
Select the device site from the list box on the PAS toolbar.
Point to RT Min/Max Log on the Monitor menu, and then select a
data set you want to view.
Click on the Pollbutton .
PAS supports 9 programmable data sets that you can organize as you
wish. To build your data sets, select MinMax Data Sets from the
Monitor menu or click on the button on the local toolbar.
See Working with Tables in Chapter 9 for more information on working

with tables.
7.3 Viewing Real-time Waveforms

To retrieve real-time waveforms from your meter:

Select the device site from the list box on the toolbar.
Select RT Waveform Monitor from the Monitor menu or click on the
button on the PAS toolbar.
Use the Poll button for a single-step poll or the Continuous poll
button for continuous polling.
To stop continuous polling, click on the Stop button .
The meter provides simultaneous capture of six one-cycle voltage and

current AC waveforms at a rate of 64 samples per cycle. To give you a
more representative picture, PAS extends the waveforms across the
window up to eight cycles by repeating the captured waveforms.
To select the channels you want to view, click with the right mouse
button on the waveform window, select Channels..., check the
channels for the phase you want displayed, and then click OK.
See Working with Graphic Windows in Chapter 9 for more information

on working with waveforms.
Retrieved waveforms can be displayed in different views as overlapped

or non-overlapped waveforms, as RMS cycle-by-cycle plot, or as a
harmonic spectrum chart or table.
Viewing a Waveform Graph
When you open a new file, PAS shows you a waveform graph with non-
overlapped waveforms as shown in the picture above.
Click on the button on the local toolbar to see overlapped

waveforms.
Click on the button for non-overlapped waveforms.

‎Chapter 7 Monitoring Meters Viewing Real-time Waveforms
Figure ‎7-2: RT Waveform Monitor Window
Viewing a Frequency Plot
Click on the button to view a cycle-by-cycle frequency plot for the

sampled voltage waveforms.
Viewing a Harmonic Spectrum
Click on the button to view a spectrum chart for the selected

waveform channel. PAS provides voltage, current, active power and
reactive power spectrum charts. See Viewing Real-time Harmonic
Spectrum for more information on viewing options.
Viewing Phasor Diagrams
The phasor diagrams show you relative magnitudes and angles of the
three-phase voltage and current fundamental component. All angles
are shown relative to the reference voltage channel.
To change the reference channel, click on the waveform window with

the right mouse button, select Options..., click on the Phasor tab,
check the channel you want to make a reference channel, and then
click OK.
Viewing Symmetrical Components
Waveform views have an additional pane at the right where PAS

displays the symmetrical components for voltages and currents,
calculated for the point indicated by the left marker line.
To enable or disable the symmetrical components, click on the

waveform window with the right mouse button, select Options...,
check or uncheck the Symmetrical components box on the
Channels tab, and then click OK.

‎Chapter 7 Monitoring Meters Viewing Real-time Harmonic Spectrum
Viewing Phase-to-phase Voltages
PAS can transform phase-to-neutral voltage waveforms in

configurations with a neutral into phase-to-phase waveforms allowing
you to view the waveshape, angle relationships and harmonics of the
phase-to-phase voltages.
Click on the button on the waveform window toolbar. Click the

button once again to return to phase-to-neutral waveforms.
7.4 Viewing Real-time Harmonic Spectrum

To retrieve real-time harmonic spectrum from your meter:

Select the device site from the list box on the toolbar.
Select RT Harmonic Monitor from the Monitor menu or click on the
button on the PAS toolbar.
Click on the “Poll” or “Continuous poll” button to poll the meter

once or continuously. Click on the Stop button to stop continuous
polling.
Figure ‎7-3: RT Harmonic Monitor – Spectrum Chart
PAS retrieves harmonic spectrum for V1-V3 and I1-I3 channels.

Harmonics can be displayed as a spectrum chart for a selected channel
or in a table. PAS can also synthesize waveforms based on the
harmonic spectrum to let you view a shape of the voltage and current
waveforms in your network.
Viewing a Spectrum Chart
Click on the button to view a spectrum chart for the selected

channel. To change a channel, click on the window with the right
mouse button, select Channels..., check the channel you want
displayed, and then click OK. PAS provides voltage, current, active
power and reactive power spectrum charts.

PAS can give you indication on whether harmonic levels in the sampled
waveforms exceed compliance limits defined by the power quality
standards or local regulations.
To review or change harmonic limits:
Click on the spectrum window with the right mouse button and select
Limits….
Select a known harmonics standard, or select Custom and specify
your own harmonic limits.
Check the Enabled box to visualize harmonic faults on the spectrum
graph and in harmonic tables.
Harmonics that exceed selected compliance levels are colored in red on

the graph and in the tables.
Figure ‎7-4: Harmonic Limits
Viewing a Spectrum Table
Click on the button on the local toolbar to display the harmonics

spectrum in a tabular view for a selected phase or for all phases
together.
The spectrum table shows voltage, current, active power and reactive
power harmonic components both in percent of the fundamental and in
natural units, and harmonic phase angles.
To change a phase, click on the window with the right mouse button,
select Options..., check the phase you want displayed, and then click
OK.

Figure ‎7-5: RT Harmonic Monitor – Spectrum Table
Viewing Synthesized Waveforms

To view the synthesize waveforms based on the sampled harmonic
spectrum, click on the button on the local toolbar to view non-
overlapped voltage and current waveforms, or click on the button to
view them overlapped.
PAS shows a pair of 4-cycle voltage and current synthesized AC
waveforms for a single phase.
To select the channels you want to view, click with the right mouse button
on the waveform window, select “Channels...”, check the channels for the
phase you want displayed, and then click OK.

Figure ‎7-6: RT Harmonic Monitor – Synthesized Waveforms

‎Chapter 8 Retrieving and Storing Files Uploading Files on Demand
Chapter 8 Retrieving and Storing Files

PAS allows you to retrieve recorded events and data from your meters
and to save them to files on your PC in the Microsoft Access database
format.
Historical data can be uploaded on demand any time you need it, or
periodically through the Upload Scheduler that retrieves data
automatically on a predefined schedule, for example, daily, weekly or
monthly.
If you do not change the destination database location, new data is

added to the same database so you can store long-term data profiles
in one database regardless of the upload schedule you selected.
8.1 Uploading Files on Demand

To retrieve the log files from your meter:

Select a device site from the list box on the PAS toolbar.
Select Upload Logs from the Logs menu.
Select a database, or type the name for a new database, and select a
directory where you want to save it.
Click on the Select Logs button and check boxes for logs you want to
be retrieved from the meter.
If you wish to retrieve data starting with a known date, check the
“From” box and select the start date for retrieving data.
If you wish to retrieve data recorded before a known date, check the
“To” box and select the last date for retrieving data.
Click OK.

‎Chapter 8 Retrieving and Storing Files Using the Upload Scheduler
8.2 Using the Upload Scheduler

To setup the Upload Scheduler:
Select Upload Scheduler from the Logs menu.
Figure ‎8-1: Upload Scheduler Setup Dialog Box
Click Add Site, point to the site database for which you want to
organize the schedule, and then click OK.
Click Browse and select a database for storing retrieved data, or type
the name for a new database, select a directory where you want to
save it, and then click OK.
Click Configure or double click on the site row.

‎Chapter 8 Retrieving and Storing Files Using the Upload Scheduler
Select a daily, weekly or monthly schedule, and adjust the start time.
If you wish to upload data periodically in predefined intervals, click on
Periodic and define the time period in hours and minutes.
Select the number of attempts to upload data in the event of
temporary communication problems or unavailability of your device,
and the delay between attempts in minutes and seconds.
If you wish to use the schedule to synchronize the device clock with
your PC, check the RTC Synchronization Enable box. If your device
is password protected by a communications password, type in the
password you set in the device to allow PAS to update the clock.
Click on the Select Logs button, check the boxes for logs you want to
upload on a schedule, and then click OK.
Check the Enabled box at left to activate a schedule for the device.
Click Close to store your schedule.
To keep the Upload Scheduler running, the On-line button on the

PAS toolbar must be checked all the time. If you uncheck it, the
scheduler stops operations. This does not cause loss of data, since the
scheduler will resume operations when you check this button again.
Suspending the Scheduler
To suspend the Upload Scheduler, check the Suspend Scheduler box

at right. To activate the Upload Scheduler, leave this box unchecked.
Running the Scheduler on Demand
You can run the scheduler at any time outside the schedule by
checking the Start Now box at right. This is a one-time action. After
uploading is completed, the Upload Scheduler un-checks this box
automatically.
Reviewing Upload Problems
When the Upload Scheduler fails to retrieve data from the device, or
some data is missing, or another problem occurs, it puts an error
message to the log file. To review this file, select System Log from
the View menu.

‎Chapter 8 Retrieving and Storing Files Viewing Files On-line
8.3 Viewing Files On-line

Sometimes, it is useful to review a particular piece of historical data
on-line at the time you expect new events to appear in the log. PAS
allows you to retrieve historical data from a particular log without
storing it to a file. The data appears only in the window on your screen.
You can save it manually to the database.
To view the log data on-line, check the On-line button on the PAS
toolbar, select the log you want to retrieve in the Logs menu, and then
click on the Pollbutton . Only new log records are retrieved from
the device. If you want to review the entire log from the beginning,
click on the Restore logbutton , and then click on the Poll button
.
NOTE
When reading multi-section profile data, only the first section is

available for reading online.
See Chapter 9 Viewing Files for information on using different log

views.
8.4 Exporting Files

Exporting Files in COMTRADE and PQDIF Formats
The COMTRADE and PQDIF file converters allow you to convert saved
real-time waveforms into COMTRADE or PQDIF file format, and data
log tables – into PQDIF format.
Manual Converting
To manually convert your waveforms or a data log into COMTRADE or

PQDIF format:
Click on the Export button on the PAS toolbar.
Select the database and a data log table you want to export, and then
click Open.

‎Chapter 8 Retrieving and Storing Files Exporting Files
Select a folder where you want to store your exported files, type a file
name that identifies your files, select a file output format, and then
click on the Save button.
The PQDIF files are commonly recorded in compressed format. If you
do not want your files to be compressed, uncheck the Compress box
before saving the file.
In COMTRADE format, each waveform event is recorded into a

separate file.
PQDIF file names are followed by a timestamp of the first event

recorded to the file, and may look like follows:
12KVSUB_20040928T133038.pqd.
Automatic Converting
PAS allows you to automatically convert data logs into PQDIF format at
the time you upload data from your devices via the Upload Scheduler.
To automatically convert your data log tables into PQDIF format:

Open the Upload Scheduler.
Highlight a desired device site with the left mouse button, and then
click on the Export button.
Check the Enabled box for a data log or a waveform log table you
want to automatically convert at the upload time.
Highlight the Record to… row for the selected table and click on the
Browse button.
Select a folder where you want to store converted files, type in the
converted file’s name, select a desired output file format, and then
click on Save.
Repeat the same for all tables you wish to be converted.
Click OK.
Exporting Files in Excel Format

PAS allows you to convert data tables into the Microsoft Excel
workbook format, either manually, or automatically while retrieving
data from your meters via the Upload Scheduler.

‎Chapter 8 Retrieving and Storing Files Archiving Files
To store files in Excel format, follow instructions in the previous section

and select Excel Workbook as the output file format.
The first row of the Excel table lists data names (see Appendix D) and
the second row provides data codes, which identify recorded data
points (see Modbus communications guide for data codes) that may be
useful for automated table processing.
Each table row is provided with the device identifier that you can
define in the meter database (see Creating a New Site for your Meter).
8.5 Archiving Files

Microsoft Access databases tend to grow fast. Databases above 0.5
Gigabytes can drastically slow down file operations.
To avoid enormous growing files, you can either periodically change

the target database, or use the Upload Scheduler’s file archiver to
automatically move older data to archives.
The Upload Scheduler archives files upon a weekly, monthly or yearly

schedule. When archiving data, a new database is created to where
older data from your present database with the expired archiving date
is moved.
An archive file keeps the original database name to which the date of
the oldest database record is added, so you can easily identify your
archives and work with them as you work with a regular database.
To provide a schedule for archiving files:

When defining a schedule for uploading files from your meter, click on
Configure or double click on the site row.
Click Auto Archive.
Check the Enable box and select a periodic schedule for archiving your
files for this site.
Click OK.
To avoid archiving partially updated data, archiving is performed in a

day after expiring a scheduled period and not before 2 hours a.m.

‎Chapter 9 Viewing Files Operations with Files
Chapter 9 Viewing Files

9.1 Operations with Files
Files you read from the meters are stored in one or in a number of
tables in the meter database. Sections of multi-section files like energy
load profiles are stored in multiple tables – each file section in a
separate database table.
Opening a Database Table
To open a database table:
Click on the Open button on the PAS toolbar, or select Open...

from the File menu.
Select Access Database (*.mdb) in the Files of type box; select a
directory where your files are located, and point to the file you wish to
open.
Select a desired table on the right pane, and then click Open, or
double click on the table name.
Names of the last 16 files you opened are stored in the File menu, so
you can select them directly from the menu.
Saving Data to a File
To save data from the open database table to a file:
Click on the Savebutton , and select a directory where you want

your file to be stored.
Select a database or type the name for a new database.
Click Save.
To avoid confusion, do not store data files into the Sites directory
where site databases are located.
9.2 Viewing Options

Customizing Views
Changing Date Order
To change the way PAS displays the date:

Select Options from the Tools menu and click on the Preferences
tab.
Select the preferred date order.
Click OK.
Selecting Timestamp Format
The timestamp is normally recorded and displayed on the screen at a

1-ms resolution. If you have an application that does not support this
format, you may instruct PAS to drop milliseconds.
To change the way PAS records and displays the timestamp:

Select Options from the Tools menu and click on the Preferences
tab.

‎Chapter 9 Viewing Files Viewing Options
Select the preferred timestamp format.

Click OK.
Working with Tables

Selecting Font and Grid
To change the table font or a type of the grid lines:

Click with right mouse button on the table, select Options and click on
the Table tab.
Select the font type and size and how you wish the table grid to be
shown.
Click OK.
Selecting Primary and Secondary Units
Voltages and currents can be displayed in primary or secondary units.
To change units, click on the table with the right mouse button, select
Options, select the desired units for voltages and currents, and then
click OK.
Copying a Table
To copy the entire table, or its part, into the Clipboard or into another
application such as Microsoft Excel or Word:
Click on the data window with the right mouse button and choose
Select All, or click on the upper-left corner of the table (where the
“No.” label is commonly displayed).
Click with the right mouse button on the window again and choose
Copy, or click on the Copy button on the PAS toolbar.
Run the application to which you want to copy data, position the cursor
at the correct place.
Click the Paste button on the application's toolbar or select Paste

from the Edit menu.
When copying, table columns are separated by a tab character.
Printing a Table
To check how your document appears on a printed page, select

PrintPreview from the File menu.
To print a table to a printer, click on the print button on the

toolbar, select a printer and click OK.
Working with Graphic Windows

Selecting Channels
To select the channels you want to view on the screen, click on the
graph window with the right mouse button, select Channels..., check
the channels you want displayed, and then click OK.
Checkboxes for channels that are not available in the present view are
dimmed.

‎Chapter 9 Viewing Files Viewing Options
Selecting Primary and Secondary Units
Voltages and currents can be displayed in primary or secondary units.
To change units, click on the table with the right mouse button, select
Options, select the desired units for voltages and currents, and then
click OK.
Selecting the Time Axis
In waveform views, the horizontal axis can be displayed either in

absolute time with date and time stamps, or in milliseconds relatively
to the beginning of a waveform.
To change the time units, click on the waveform window with the right
mouse button, select Options..., click on the Axes tab, select the
desired units, and then click OK.
Selecting Line Styles and Colors
Channel waveforms can be displayed using different colors and line

styles.
To change the colors or line styles, click on the graph window with the
right mouse button, select Options..., click on the Display tab, adjust
colors and styles, and then click OK.
Selecting Grid and Frame Colors
Click on the graph window with the right mouse button, select
Options..., and click on the Display tab
To change the color or style of the grid lines, click on the Grid line on
the left pane, and then select the color and style for the grid. To
disable the grid, uncheck the Grid Visible box.
To change the window frame color to white, check the White Frame
box at right.
Using Marker Lines
The waveform and trend windows have two blue dashed marker lines.
The left marker indicates the starting position and the right marker
indicates the end position for calculating the average and peak values.
The minimum distance between the two markers is exactly one cycle.
To change the marker position, click on the button, or click on the

window with the right mouse button and select Set Marker, and then
click on the point where you want to put the marker.
You can also drag both markers with the mouse, or use the right and
left arrow keys on your keyboard to change the marker position. Click
on the graph pane to allow the keyboard to get your input before using
the keyboard.
Delta Measurements
To measure the distance between two waveform or trend points, click

on the Deltabutton , then click on the first point, and then click on
the second point.

‎Chapter 9 Viewing Files Viewing the Event Log
The first reference point is still frozen until you uncheck and check the
Delta button again, while the second point can be placed anywhere
within the graph line by clicking on the graph to the left or right from
the reference point.
To disable delta measurements, click on the Delta button once again.
Using a Zoom
You can use a horizontal and, for waveforms, also a vertical, zoom to
change size of your graph.
Use the buttons on your local toolbar to zoom in and

zoom out. One click gives you a 100-percent horizontal or 50-percent
vertical zoom. Two buttons representing magnifying glasses
give you a proportional zoom in both directions.
Copying a Graph
To copy a graph, or its part, into the Clipboard or into another

application such as Microsoft Excel or Word:
Click on the graph window with the right mouse button and choose
Copy All, or Copy Waveform. Some windows may have additional
options.
Position the cursor at the place where you whish to copy the graph.
Click the Paste button on the application's toolbar or select Paste

from the Edit menu.
Printing a Graph
To check how the graph appears on a printed page, select Print

Preview from the File menu.
To print a graph to a printer, click on the Print button on the PAS

toolbar, select a printer and click OK.
9.3 Viewing the Event Log

The Event log contains time-tagged events related to configuration
changes, resets and device diagnostics.
The Event log is displayed in a tabular view, one event per row. Use
the scroll bar to view the entire log contents.

‎Chapter 9 Viewing Files Viewing the Data Log
Figure ‎9-1: Event Log Window
See Working with Tables for more information on viewing options.
Filtering and Sorting Events
You can use filtering to find and work with a subset of events that
meet the criteria you specify.
Click on the Filter button , or click on the report window with the
right mouse button and select Filter.... Check the causes of events you
want to display, and then click OK. PAS temporary hides rows you do
not want displayed.
To change the default sorting order based on the date and time, click
on the Sortbutton , or click on the report window with the right
mouse button and select Sort..., check the desired sort order, and
then click OK.
9.4 Viewing the Data Log

Data log files can be displayed in a tabular view, one data record per
row, or in a graphical view as a data trend graph.

‎Chapter 9 Viewing Files Viewing the Data Log
Figure ‎9-2: Data Log Window
Viewing Data Trend
To view data in a graphical form, click on the Data Trend button on

the local toolbar.
To change the time range for your graph, click on the Time Range
button on the local toolbar, and then select the desired date and
time range.

‎Appendix A Technical Specifications
Appendix A Technical Specifications

A.1 Environmental Conditions
Operational ambient temperature limit range: –25C to +60C
Specified ambient temperature range: –20C to +60C
Long-term damp heat withstand according to IEC 68-2-3 <95% (non-
condensing), +40 C
Transport and storage temperature range: –30C to +85 C
IEC 60068-2-6, AS 60068-2-6 [18]: Vibration
Frequency range: 10Hz to 150Hz
Vibration time (each axis): 75 min
Sweep rate: 1 oct/min
Max Vibration level:10 m/s2 (1g), f > 60Hz
IEC 60068-2-27, AS 60068-2-27 [19]: Shock
Shock level: 30 g
Time duration: 18 ms
Shape: Half sine
Number of shocks: 18
A.2 Construction
Case enclosure: Reinforced Polycarbonate
Packaging case: Carton and Stratocell® (Polyethylene Foam) brackets
Labels: Polyester film (UL94-V0)
A.3 Three Phase Power Supply – EM133-SE (Y &)

Indirect Connection or Direct Connection using HACS
Rated input from 1, 2 or 3 phases: 3 x 120/207-277/480 VAC 50/60Hz
Burden 2VA per phase
Direct Connection
Rated input from 1, 2 or 3 phases: 3 x 120/207-230/400 VAC 50/60Hz
Burden 2VA per phase
Isolation:
Input to ground: 4000V AC
A.4 Auxiliary Power Supply – EM132-133

Rated input: 40-300VAC 50/60Hz, 40-300VDC, Burden 5VA
Frequency range operation 25-400 Hz
Isolation:
Input to ground: 4000V AC

A.5 Input Ratings

Voltage Inputs – Installation category III
Model with 3 Phase Power Supply – EM133-SE (Y &)
Operating range: 120/207V to 277/480VAC for 1A/5A/RS5 models
Operating range: 120/207V to 230/400VAC for HACS models
Frequency range measurement 50-60 Hz
Burden for 277V: < 1.5 VA
Burden for 120V: < 2 VA
Model with Aux. Power Supply – EM132-133
Operating range: up to 400/690 VAC
Measurement range: direct input and input via PT up to 828VAC line-to-
line, up to 480VAC line-to-neutral
Over-voltage withstands: 1000 VAC continuous, 2000 VAC for 1 second
Input impedance: 1000 k
Current Inputs (via CT) – Installation category III
Galvanic isolation: 4000V AC
5A secondary (standard)
Current rating: 5A RMS
Maximum continuous current: 10A RMS
Burden: < 0.2 VA @ In=5A
Overload withstanding:
15A RMS continuous, 300A RMS for 1 second
1A secondary (1A option)
Maximum continuous current: 2A RMS
50A direct (100A option)
Maximum continuous current: 100A RMS @ 55°C ambient temperature
Maximum continuous current: 60A RMS @ 60°C ambient temperature
Frequency range measurement 25-400 Hz up to 50A

100A RMS continuous @ 55°C, 2500A RMS for 1 second

40mA secondary – with HACS (external CT option)
External CT Operating range: continuous 100-1200A RMS
5mA secondary – with external CT (RS5 option)
Operating range: continuous 10A RMS
Sampling Rate measurement
128 samples per cycle
A.6 Relay Outputs

Solid State relay standard
1 relay rated at 0.15A/24V AC/DC, 1 contact (SPST Form A)
Galvanic isolation: 4000V AC 1 min
Operate time: 1 ms max.
Release time: 0.25 ms max.
Update time: 1 cycle
Electromechanical relay - DRY contact, option (4DI/2DO and
12DI/4DO Optional modules)
2 or 4 relays rated at 5A/250V AC; 5A/30V DC, 1 contact (SPST Form A)

Galvanic isolation:
Between contacts and coil: 3000V AC 1 min
Between open contacts: 750V AC
Release time: 5 ms max.
Solid State relay option (4DI/2DO Optional module)
2 relays rated at 0.15A/250V AC/DC, 1 contact (SPST Form A)
Release time: 0.25 ms max.
Connector type: removable, 4 pins.
A.7 Digital Inputs

Digital Input (standard)
1 Digital Inputs Dry Contacts, internally wetted @ 5VDC

Sensitivity: Open @ input resistance >100 k, Closed @ Input

resistance < 100 
Internal power supply: 5VDC
Scan time: 1 ms
Digital Input (option)
4 Digital Inputs Dry Contacts, internally wetted @ 24VDC (4DI/2DO
Optional module)
Internal power supply: 24V DC
Scan time: 1 ms
8 Digital Inputs Dry Contacts, internally wetted @ 24VDC (8DI
Optional module)
Internal power supply: 24V DC
Scan time: 1 ms
Connectors type: removable, 4 and 5 pins
12 Digital Inputs Dry Contacts (12DI/4DO Optional module)
Scan time: 1 ms
Internally/externally wetted @ 24VDC - option 1/2:
Wet contact sensing: Open > 16k, Closed < 10k
Externally wetted @ 120VDC - option 3:
Wet contact sensing option 1: Open > 160k, Closed <60k
Externally wetted @ 220VDC - option 4:
Wet contact sensing option 1: Open >320k, Closed <100k
A.8 Optional Analog Outputs

4 Analog Outputs optically isolated (AO Optional module)
Ranges (upon order):
1 mA, maximum load 5 k (100% overload)
0-20 mA, maximum load 510 
4-20 mA, maximum load 510 
0-1 mA, maximum load 5 k  (100% overload)
Isolation: 2500V AC 1 min
Power supply: internal
Accuracy: 0.5% FS


A.9 Communication Ports

COM1 (standard)
RS-485 optically isolated port
Baud rate: up to 115.2 kbps.
Protocols: Modbus RTU, DNP3, SATEC ASCII and IEC 60870-5-101
Connector type: removable, 3 pins
COM2 option
Ethernet Port(Optional module)
Transformer-isolated 10/100BaseT Ethernet port
Protocols: MODBUS/TCP (Port 502), DNP3/TCP (Port 20000),
IEC 60870-5-104
Number of simultaneous connections: 4 (2 MODBUS/TCP + 2 DNP3/TCP).
Connector type: RJ45 modular.
PROFIBUS DP (IEC 61158) (Optional module)
RS-485 optically isolated PROFIBUS interface.
Baud rate: 9600 bit/s – 12 Mb/s (auto detection).
32 bytes input, 32 bytes output.
Protocols: PROFIBUS
CANopen (Optional module)
RS-485 optically isolated CANopen interface.
Protocols: CANopen
RS-232/422-485 Port (Optional module)
RS-232 or RS-422/485 optically isolated port
Protocols: MODBUS RTU, DNP3, and SATEC ASCII
Connector type: removable, 5 pins for RS-422/485 and DB9 for RS-232.
COM3 (standard)
Infra-Red COM port
Protocols: MODBUS RTU
A.10 Real-time Clock

Standard Meter Clock
Crystal Clock Accuracy: typical error 13.15 sec per month (2.63 minutes
per year) @ 25C (±5ppm)

Typical clock retention time: 15 months

TOU Module Meter Clock (option)
Accuracy: typical error 7 seconds per month @ 25C (±2.5ppm)
Typical clock retention time: 36 months

‎Appendix B Standards Compliance
Appendix B Standards Compliance

Per EN50470-1-3, IEC 62052-11, NMI M6-1 and ANSI C12.1
UL916 E472110
Accuracy:
EN50470-3, class C
IEC/AZ 62053-22, class 0.5S – active energy
IEC 62053-21, class 0.5 – reactive energy
IEC 60688, class 0.5S – active energy
IEC 60688, class 1 – reactive energy
ANSI C12.20, class 100 (HACS), accuracy class 0.5
Electromagnetic Immunity according to IEC 62052-11 and
EN50470-1/3:
IEC61000-4-2: Electrostatic discharge, 15/8 kV air/contact
IEC61000-4-3: Electromagnetic RF Fields, 10V/m @ 80 MHz – 1000MHz
IEC61000-4-4: Fast Transients burst, 4KV on current and voltage circuits
and 2 KV for auxiliary circuits
IEC61000-4-5: Surge 4KV on current and voltage circuits and 1 KV for
auxiliary circuits
IEC61000-4-6: Conducted Radio-frequency, 10V @ 0.15 MHz – 80MHz
IEC61000-4-8: Power Frequency Magnetic Field
IEC61000-4-12: Oscillatory waves
Electromagnetic Emission:
Comply with IEC CISPR 22:
Radiated Class B
Conducted class A
Conducted class B (with SATEC RF choke)
Safety/Construction:
EN/IEC 62052-11: 4000V AC @ 1 minute, 6KV/500Ω @ 1.2/50 μs impulse
NMI M6-1 (EM133-SE only): 4000V AC @ 1 minute, 12KV/40Ω @ 1.2/50
μs impulse
UL916, UL1059

Measurement Specifications
Table 23: Measurement Specifications Parameters
Parameter Full Scale @ Accuracy Range

InputRange % % Conditions
Reading FS
Voltage, V 120VxPT @ 120V 0.2 0.02 10% to 120% 0 to 1,150,000 V
400VxPT @ 690V 0.2 0.02 10% to 115% Starting voltage
1.5-5.0% FS (selectable)
Voltage, V VL = 120V, 0.2 0.02 10% to 120% 80 to 1,150,000 V
(EM133-SE model) VL = 230V 0.2 0.02 10% to 115% Starting voltage 80VAC
(w/1phase)
Line current, A CT 0.2 0.02 For In = 5A Starting current 0.1% FS
1% to 200% FS
For In = 1A
2% to 200% FS
Line current - 50 A 0.2 0.02 2% to 200% FS Starting current 0.1% FS
direct
Active power, kW 0.36PTCT @ 120V 0.3 0.02 |PF|  0.51 -10,000,000 kW to
1.2PTCT @ 690V +10,000,000 kW
34.5 @(230V,50A)
Reactive power, 0.36PTCT@ 120V 0.3 |PF|  0.91 -10,000,000 kvar to
kvar 1.2PTCT @ 690V 0.03 +10,000,000 kvar
34.5 @(230V,50A)
Apparent power, 0.36PTCT @ 120V 0.3 0.02 |PF|  0.51 0 to 10,000,000 kVA
kVA 1.2PTCT @ 690V
34.5 @(230V,50A)
Power factor 1.000 0.2 |PF|  0.5, -0.999 to +1.000
I  2% FSI
Frequency 50 Hz 0.02 VL-N> 25V 15 Hz to 70 Hz
60 Hz 0.02 15 Hz to 70 Hz
25 Hz 0.04 15 Hz to 70 Hz
400 Hz 0.04 320 Hz to 480 Hz
Total Harmonic 999.9 1.5 0.2 THD  1%, 0 to 999.9
Distortion, THD V  10% FSV and
V(I), %Vf (%If) VL-N> 25V,
I  10% FSI
Total Demand 100 1.5 TDD  1%, 0 to 100
Distortion, TDD, % I  10% FSI,
VL-N> 25V
Active energy In = 5 and 1 A Class C as per EN50470-3, Class 0 to 999,999,999 kWh
Import & Export 0.5S under conditions as per
IEC/AZ 62053-22:2003 at 50/60 Hz
& ANSI C12.20 Ac. Class 0.5
Reactive energy In = 5 and 1 A Class 0.5S under conditions as per 0 to 999,999,999 kvarh
Import & Export IEC 62053-22:2003, |PF|  0.9 and
at 50/60 Hz
Apparent energy In = 5 and 1 A Class 0.5S under conditions as per 0 to 999,999,999 kVAh
IEC 62053-22:2003 at 50/60 Hz
PT - external potential transformer ratio
CT - primary current rating of the external current transformer
FSV - voltage full scale
FSI - current full scale
Vf - fundamental voltage
If - fundamental current
1
@ 80% to 120% of voltage FS, 1% to 200% of current FS at (In = 5 and 1 A), 2% to 200% of
current FS 50 A and frequency 50/60 Hz

NOTES:
 Accuracy is expressed as  (percentage of reading + percentage of full
scale)  1 digit. This does not include inaccuracies introduced by the
user's potential and current transformers. Accuracy calculated at
1second average.
 Specifications assume: voltage and current waveforms with THD  5%
for kvar, kVA and PF, and reference operating temperature 20C - 26C.
 Measurement error is typically less than the maximum error indicated.

‎Appendix C Analog Output Parameters
Appendix C Analog Output

Parameters
The following table lists parameters that can be provided on the
meter’s analog outputs.
Table 24: Analog Output Parameters

Designation Description
NONE None (output disabled)
1-Cycle Phase Values
V1/12 RT1 V1/V12 Voltage
V2/23 RT 1 V2/V23 Voltage
V3/31 RT 1 V3/V31 Voltage
V12 RT V12 Voltage
V23 RT V23 Voltage
V31 RT V31 Voltage
I1 RT I1 Current
I2 RT I2 Current
I3 RT I3 Current
1-Cycle Total Values
kW RT Total kW
kvar RT Total kvar
kVA RT Total kVA
PF RT Total PF
PF LAG RT Total PF Lag
PF LEAD RT Total PF Lead
1-Cycle Auxiliary Values
In RT In Current
FREQ RT Frequency
1-Sec Phase Values
V1/12 AVR 1 V1/V12 Voltage
V12 AVR V12 Voltage
V23 AVR V23 Voltage
V31 AVR V31 Voltage
I1 AVR I1 Current
I2 AVR I2 Current
I3 AVR I3 Current
1-Sec Total Values
kW AVR Total kW
kvar AVR Total kvar
kVA AVR Total kVA
PF AVR Total PF
PF LAG AVR Total PF Lag
PF LEAD AVR Total PF Lead
1-Sec Auxiliary Values
In AVR In Current
FREQ AVR Frequency

‎Appendix C
Demands E, EH
kW IMP ACD Accumulated kW import demand

kW EXP ACD Accumulated kW export demand
kvar IMP ACD Accumulated kvar import demand
kvar EXP ACD Accumulated kvar export demand
kVA ACD Accumulated kVA demand
1In4LN3, 3LN3 and 3BLN3 wiring modes, the voltages will be line-to-
neutral; for any other wiring mode, they will be line-to-line voltages.

‎Appendix D Setpoint Triggers and Actions
Appendix D Setpoint Triggers and

Actions
Table 25: Setpoint Triggers
NONE None (condition is not active)
Status Inputs
STAT INP #1 ON Status input #1 ON
STAT INP #1 OFF Status input #1 OFF
Relays
RELAY #1 ON Relay #1 ON
RELAY #1 OFF Relay #1 OFF
Phase Reversal
POS PHASE REVERSAL Positive phase rotation reversal
NEG PHASE REVERSAL Negative phase rotation reversal
Low/High 1-Cycle Values on any Phase
HI VOLT RT 1 High voltage
LO VOLT RT 1 Low voltage
HI AMPS RT High current
LO AMPS RT Low current
HI V THD 2 High voltage THD
HI I THD 2 High current THD
HI KF RT High K-Factor
HI I TDD High current TDD
1-Cycle Auxiliary Values
HI FREQ RT High frequency
LO FREQ RT Low frequency
HI V UNB% RT 1 High voltage unbalance
HI I UNB% RT High current unbalance
1-Sec Phase Values
HI I1 AVR High I1 current
LO I1 AVR Low I1 current

‎Appendix D
1-Sec Values on any Phase
HI VOLT AVR 1 High voltage
LO VOLT AVR 1 Low voltage
HI AMPS AVR High current
LO AMPS AVR Low current
1-Sec Total Values
HI kW IMP AVR High total kW import
HI kW EXP AVR High total kW export
HI kvar IMP AVR High total kvar import
HI kvar EXP AVR High total kvar export
HI kVA AVR High total kVA
HI PF LAG AVR Low total PF Lag
HI PF LEAD AVR Low total PF Lead
1-Sec Auxiliary Values
HI In AVR High neutral current
HI FREQ RT High frequency
LO FREQ RT Low frequency
Demands
HI V1/12 DMD 1 High V1/V12 Volt demand
HI I1 DMD High I1 Ampere demand
HI kW IMP BD High block kW import demand
HI kvar IMP BD High block kvar import demand
HI kVA BD High block kVA demand
HI kW IMP SD High sliding window kW import demand
HI kvar IMPSD High sliding window kvar import demand
HI kVA SD High sliding window kVA demand
HI kW IMP ACD High accumulated kW import demand
HI kvar IMP ACD High accumulated kvar import demand
HI kVA ACD High accumulated kVA demand
HI kW IMP PRD High predicted kW import demand
HI kvar IMP PRD High predicted kvar import demand
HI kVA PRD High predicted kVA demand
Time and Date Parameters
DAY OF WEEK Day of week
YEAR Year
MONTH Month
DAY OF MONTH Day of month
HOURS Hours
MINUTES Minutes
SECONDS Seconds
MINUTE INTERVAL Minute interval: 1-5, 10, 15, 20, 30, 60 min
1In
4LN3, 3LN3 and 3BLN3 wiring modes, the voltages will be line-
to-neutral; for any other wiring mode, they will be line-to-line
voltages.

‎Appendix D Setpoint Triggers and Actions
Table 26: Setpoint Actions

NONE None (no action)
OPERATE RELAY #1 Operate relay RO1
RELEASE RELAY #1 Release latched relay RO1
INC CNT #1 Increment counter #1
TIME CNT #1 Count operation time using counter #1
NOTIFICATION Send a notification message
DATA LOG #1 Record data to Data Log #1

‎Appendix E
Appendix E Parameters for Data

Monitoring and Logging
The following table lists parameters measured by the meter that are
available for monitoring through communications and for recording to a
data log file. The left column shows data abbreviations used in PAS.
Parameter groups are highlighted in bold.
Table 27: Data Monitoring and Logging Parameters

NONE None (stub, read as zero)
DIGITAL INPUTS Digital Inputs
DI1:16 Digital Inputs Status DI1:DI6
RELAYS Relays
RO1:16 Relay Status RO1:RO3
COUNTERS Pulse Counters
COUNTER 1 Counter #1
RT PHASE 1-Cycle Phase Values
V1 V1/V12 Voltage 1
V2 V2/V23 Voltage 1
V3 V3/V31 Voltage 1
I1 I1 Current
I2 I2 Current
I3 I3 Current
kW L1 kW L1
kW L2 kW L2
kW L3 kW L3
kvar L1 kvar L1
kvar L2 kvar L2
kvar L3 kvar L3
kVA L1 kVA L1
kVA L2 kVA L2
kVA L3 kVA L3
PF L1 Power factor L1
V1 THD V1/V12 Voltage THD 1
I1 THD I1 Current THD
I1 KF I1 K-Factor
I2 KF I2 K-Factor
I3 KF I3 K-Factor
I1 TDD I1 Current TDD

‎Appendix E Parameters for Data Monitoring and Logging
V12 V12 Voltage
V23 V23 Voltage
V31 V31 Voltage
RT TOTAL 1-Cycle Total Values
kW Total kW
kvar Total kvar
kVA Total kVA
PF Total PF
PF LAG Total PF lag
PF LEAD Total PF lead
kW IMP Total kW import
kW EXP Total kW export
kvar IMP Total kvar import
kvar EXP Total kvar export
V AVG 3-phase average L-N/L-L voltage
V LL AVG 3-phase average L-L voltage
I AVG 3-phase average current
RT AUX 1-Cycle Auxiliary Values
In In (neutral) Current
FREQ Frequency
V UNB% Voltage unbalance 2
I UNB% Current unbalance 2
AVR PHASE 1-Second Phase Values
V1 V1/V12 Voltage
V2 V2/V23 Voltage
V3 V3/V31 Voltage
I1 I1 Current
I2 I2 Current
I3 I3 Current
kW L1 kW L1
kW L2 kW L2
kW L3 kW L3
kvar L1 kvar L1
kvar L2 kvar L2
kvar L3 kvar L3
kVA L1 kVA L1
kVA L2 kVA L2
kVA L3 kVA L3
I1 KF I1 K-Factor

‎Appendix E
I2 KF I2 K-Factor
I3 KF I3 K-Factor
V12 V12 Voltage
V23 V23 Voltage
V31 V31 Voltage
AVR TOTAL 1-Second Total Values
kW Total kW
kvar Total kvar
kVA Total kVA
PF Total PF
PF LAG Total PF lag
PF LEAD Total PF lead
kW IMP Total kW import
kW EXP Total kW export
kvar IMP Total kvar import
kvar EXP Total kvar export
V AVG 3-phase average L-N/L-L voltage 1
V LL AVG 3-phase average L-L voltage
I AVG 3-phase average current
AVR AUX 1-Second Auxiliary Values
In In (neutral) Current
FREQ Frequency
V UNB% Voltage unbalance 2
I UNB% Current unbalance 2
PHASORS Phasors
V1 Mag V1/V12 Voltage magnitude 1
I1 Mag I1 Current magnitude
V1 Ang V1/V12 Voltage angle 1
I1 Ang I1 Current angle
DEMANDS Present Demands (Power Demands E, EH)
V1 DMD V1/V12 Volt demand 1
I1 DMD I1 Ampere demand
kW IMP BD kW import block demand
kvar IMP BD kvar import block demand
kVA BD kVA block demand

kW IMP SD kW import sliding window demand
kvar IMPSD kvar import sliding window demand
kVA SD kVA sliding window demand
kW IMP ACD kW import accumulated demand
kvar IMP ACD kvar import accumulated demand
kVA ACD kVA accumulated demand
kW IMP PRD kW import predicted sliding window demand
kvar IMP PRD kvar import predicted sliding window demand
kVA PRD kVA predicted sliding window demand
PF IMP@kVA DMD PF (import) at Maximum kVA sliding window demand
kW EXP BD kW export block demand
kvar EXP BD kvar export block demand
kW EXP SD kW export sliding window demand
kvar EXPSD kvar export sliding window demand
kW EXP ACD kW export accumulated demand
kvar EXP ACD kvar export accumulated demand
kW EXP PRD kW export predicted sliding window demand
kvar EXP PRD kvar export predicted sliding window demand
In DMD In (neutral) current demand
SUMM ACC DMD Billing Summary (Total) Accumulated Demands
REG1 ACD Register #1 accumulated demand
SUMM BLK DMD Billing Summary (Total) Block Demands
REG1 BD Register #1 block demand
SUMM SW DMD Billing Summary (Total) Sliding Demands
REG1 SD Register #1 sliding demand
ENERGY Total Energy
kWh IMPORT kWh import
kWh EXPORT kWh export
kvarh IMPORT kvarh import
kvarh EXPORT kvarh export
kVAh TOTAL kVAh total
SUMMARY REGS Billing Summary (Total and single phase) Energy
Registers
SUM REG1 Summary energy register #1
PHASE ENERGY Phase Energy
kWh IMP L1 kWh import L1
kvarh IMP L1 kvarh import L1

‎Appendix E
kVAh L1 kVAh total L1
%HD V1 V1/V12 Harmonic Distortions EH1
V1 %HD01 H01 Harmonic distortion
… ...
… ...
… ...
%HD I1 I1 Harmonic Distortions EH
I1 %HD01 H01 Harmonic distortion
… ...
… ...
… ...
ANG V1 V1/V12 Harmonic Angles EH1
V1 H01 ANG H01 Harmonic angle
… ...
… ...
… ...

ANG I1 I1 Harmonic Angles EH
I1 H01 ANG H01 Harmonic angle
… ...
… ...
… ...
H1 PHASE Fundamental (H01) Phase Values
V1 H01 V1/V12 Voltage 1
I1 H01 I1 Current
I2 H01 I2 Current
I3 H01 I3 Current
kW L1 H01 kW L1
kW L2 H01 kW L2
kW L3 H01 kW L3
kvar L1 H01 kvar L1
kvar L2 H01 kvar L2
kvar L3 H01 kvar L3
kVA L1 H01 kVA L1
kVA L2 H01 kVA L2
kVA L3 H01 kVA L3
PF L1 H01 Power factor L1
HRM TOT POW Fundamental and Harmonic Total Power Values
kW H01 Total fundamental kW
kvar H01 Total fundamental kvar
kVA H01 Total fundamental kVA
PF H01 Total fundamental PF
MIN PHASE Minimum 1-Cycle Phase Values
V1 MIN V1/V12 Voltage 1
I1 MIN I1 Current
I2 MIN I2 Current
I3 MIN I3 Current
MIN TOTAL Minimum 1-Cycle Total Values
kW MIN Total kW
kvar MIN Total kvar
kVA MIN Total kVA

‎Appendix E
PF MIN Total PF
MIN AUX Minimum 1-Cycle Auxiliary Values
In MIN In Current
FREQ MIN Frequency
MAX PHASE Maximum 1-Cycle Phase Values
V1 MAX V1/V12 Voltage 1
I1 MAX I1 Current
I2 MAX I2 Current
I3 MAX I3 Current
MAX TOTAL Maximum 1-Cycle Total Values
kW MAX Total kW
kvar MAX Total kvar
kVA MAX Total kVA
PF MAX Total PF
MAX AUX Maximum 1-Cycle Auxiliary Values
In MAX In Current
FREQ MAX Frequency
MAX DMD Maximum Demands (Power Demands E, EH)
V1 DMD MAX V1/V12 Maximum volt demand 1
I1 DMD MAX I1 Maximum ampere demand
kW IMP SD MAX Maximum kW import sliding window demand
kW EXP SD MAX Maximum kvar import sliding window demand
kvar IMP SD MAX Maximum kW export sliding window demand
kvar EXP SD MAX Maximum kvar export sliding window demand
kVA SD MAX Maximum kVA sliding window demand
In DMD MAX In (neutral) current maximum demand
MAX SUMMARY DMD Billing Summary (Total) Maximum DemandsE, EH
REG1 MD Summary register #1 maximum demand
AO RAW Raw Analog Outputs (A/D Units)
AO1 Analog output AO1
TOU PRMS TOU Parameters E, EH
ACTIVE TARIFF Active TOU tariff
ACTIVE PROFILE Active TOU profile
TOU REG1 Billing TOU Energy Register #1 E, EH
REG1 TRF1 Tariff #1 register
… …

… …
… …
… …
TOU MAX DMD REG1 Billing TOU Maximum Demand Register #1 E, EH
REG1 TRF1 MD Tariff #1 maximum demand
… …
… …
… …
… …
1In 4LN3, 3LN3 and 3BLN3 wiring modes, the voltages will be line-
to neutral; for any other wiring mode, they will be line-to-line voltages.
2The value is calculated as a relation of the maximum deviation of

phase values from a 3-phase average value to a 3-phase average.
NOTE
Designations of some enginering demands and billing energy and

demand registers are shown using a short name notation available in
PAS V1.4. By default, PAS uses long names compatible with older
versions of PAS. You can select a desired notation from the
Tools/Options/Preferences tab.
PAS does not allow to store data in files using different data names. If
you have a file uploaded with a previous version of PAS using long data

‎Appendix E
names, either continue using long data names, or store data in a new
file.
See table below for a list of parameters with short and long names.
Short Data Long Data Name Description
Name
kW IMP ACD kW IMP ACC DMD Accumulated demand
kW IMP PRD kW IMP PRD DMD Predicted sliding window demand
PF IMP@kVA MD PF IMP@kVA MXDMD PF (import) at maximum kVA demand
REG1 ACD SUM REG1 ACC DMD Billing summary (total) register accumulated demand
REG1 BD SUM REG1 BLK DMD Billing summary (total) register block demand
REG1 SD SUM REG1 SW DMD Billing summary (total) register sliding demand
REG1 SUM REG1 Billing summary (total) energy register
REG1 MD SUM REG1 DMD MAX Billing summary (total) register maximum demand
REG1 TRF1 TOU REG1 TRF1 Billing tariff energy register
REG1 TRF1 MD DMD1 TRF1 MAX Billing tariff register maximum demand
TRF1 SEASON TRF1 Generic billing tariff energy register
TRF1 MD SEASON TRF1 Generic billing tariff register maximum demand

‎Appendix F Billing/TOU Profile Log File
Appendix F Billing/TOU Profile Log

File
The following table shows the record structure for the daily billing data
profile log file.
The second column shows data abbreviations used in the PAS data log
reports. Data log file sections are highlighted in bold.
Table 28: Daily Billing/TOU Profile Data Log (Data Log #16)
Field No. Designation Description

Energy Register #1
1 REG1 Summary (total) energy reading
2 TRF1 Tariff #1 energy reading
…
Energy Register #4
1 REG4 Summary (total) energy reading
Daily Maximum Demand Register #1
1 REG1 MD Summary (total) max. demand reading
2 TRF1 MD Tariff #1 max. demand reading
…
Daily Maximum Demand Register #4
1 REG4 MD Summary (total) max. demand reading

‎Appendix F
Field No. Designation Description

The number of parameters in each section is automatically configured

depending on the number of actual tariffs you defined in the TOU Daily
Profiles.

‎Appendix G Data Scales
Appendix G Data Scales

The maximum values for volts, amps and power in the EM13X Series
setup and in communications are limited by the voltage and current
scale settings.
The following table shows the meter data scales.
Table 29: Data Scales Values

Scale Conditions Range
Maximum voltage All configurations Voltage scale  PT Ratio, V 1
(V max)
Maximum current All configurations Current scale  CT Ratio, A 2, 3
(I max)
Maximum Power 4 Wiring 4LN3, 3LN3, 3BLN3 V max  I max  3, W
Wiring 4LL3, 3LL3, 3BLL3, V max  I max  2, W
3OP2, 3OP3, 3DIR2
Maximum frequency 25, 50 or 60 Hz 100 Hz
400Hz 500 Hz
1The default voltage scale is 144V. The recommended voltage scale is

120V+20% = 144V for using with external PT’s, and 690V+20% =
828V for a direct connection to power line.
2CT Ratio = CT primary current/CT secondary current
3The default current scale is 2  CT secondary (2.0A with 1A secondary

and 10.0A with 5A secondary).
4Maximum power is rounded to whole kilowatts. With PT=1.0, it is

limited to 9,999,000 W.

‎Appendix H
Appendix H Device Diagnostic Codes

Table 30: Device Diagnostic Codes
Diagnostic Description Reason
Code
2 Memory/Data fault Hardware failure
3 Hardware watchdog reset Hardware failure
5 CPU exception Hardware failure
6 Run-time software error Hardware failure
7 Software watchdog Hardware failure
timeout
8 Power Down/Up Normal power-up sequence
9 Warm restart External restart via
communications or by
firmware upgrade
10 Configuration reset Corrupted setup data has
been replaced with the
default configuration
11 RTC fault The clock time has been lost
13 Low battery (with a Battery replacement is
battery backup unit) required
15 EEPROM fault Hardware failure

Em132-133 0

Uploaded by

Copyright:

Available Formats

Em132-133 0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Em132-133 0

Uploaded by

Copyright:

Available Formats

EM13x Series

SMART MULTIFUNCTION METER

Installation and Operation Manual

BG0491 REV. A14

All trademarks are property of their respective owners.

2 EM13x Series SMART MULTIFUNCTION METER

This equipment does not require cleaning for proper operation

EM13x Series SMART MULTIFUNCTION METER 3

Installing the EM13X SERIES

Mounting the EM13X Series on DIN-Rail

4 EM13x Series SMART MULTIFUNCTION METER

Connecting the EM13X Series Unit

Common Wiring Mode: EM13x and EM13x-SE 4LL3 or 4Ln3

EM13x Series SMART MULTIFUNCTION METER 5

To connect an Option module:

Assembly a small module

6 EM13x Series SMART MULTIFUNCTION METER

To operate the EM13X Series:

Configuring the EM13X Series remotely

At this stage, the EM13X Series should be ready for operation.

EM13x Series SMART MULTIFUNCTION METER 7

8 EM13x Series SMART MULTIFUNCTION METER

3.1 Display Operations ....................................................................................................59

EM13x Series SMART MULTIFUNCTION METER 9

Chapter 6 Device Control and Upgrading....................................................... 123

10 EM13x Series SMART MULTIFUNCTION METER

Chapter 1 General Information

The EM13X Series is a compact, multi-function, three-phase AC

The EM13X Series offers standard voltage, current, power and

The EM13X Series consists of three different models series:

‒ EM132/EM133-5, internal CT, transformer operated

‒ EM133-SE-5, internal CT, transformer operated configuration

EM13x Series SMART MULTIFUNCTION METER 11

‒ EM133-SE-50, internal CT, direct connection configuration with

‒ EM132/EM133-21DC-5, internal CT, transformer operated

 A standard RS-485 communication port, Infra-Red Communication

 Different communication options for remote communications with the

The EM13X Series is suitable for mounting on both standard DIN-Rail

The EM13X firmware Series consists of various firmware

Communication protocols App. Storage CPU

12 EM13x Series SMART MULTIFUNCTION METER

 Ampere/Volt demand meter

 25/50/60/4001 Hz measurement capabilities

Billing/TOU Energy Meter

 Three-phase total and per phase energy measurements; active,

 Time-of-Use, 4 totalization and tariff energy/demand registers x 8

 One–time easy programmable tariff calendar schedule

 Voltage and current THD, current TDD and K-Factor, up to 40th

 Voltage and current harmonic spectrum and angles

Real-time Waveform Capture

 Simultaneous 6-channel one-cycle waveform capture at a rate of 64

Programmable Logical Controller

 16 control setpoints; programmable thresholds and delays

 Relay output control

 1-cycle response time

 Non-volatile memory for long-term event and data recording

 Event recorder for logging internal diagnostic events and setup

 Two data recorders; programmable data logs on a periodic basis;

EM13x Series SMART MULTIFUNCTION METER 13