VSU 12 Splice inspection

Dimensioned drawing
Part No. 501 11731

20 … 40mm

10 - 30 V
DC

z Reliable detection of splice on paper web or

plastic web
z Sheet speeds up to 1000m/min
z Automatic adaptation to the medium
z High acoustic power (guaranteeing reliable
functionality even for thick materials)
z Ultrasonic sensor in the M18 round-sleeve
housing
z Plug connection
z Short-circuit proof PNP transistor outputs
operating-state indication by means of
LEDs
A Transmitter DB 18 U (P)
z Sensors have a very short construction (can B Receiver DB 18 U (P)
thus also be used in applications with lim- C Indicator diodes
ited available space)
z Paper tear detection (...4.5)

Electrical connection
We reserve the right to make changes • VSU_12_gb.fm

IP 65

VSU 12/4.4 VSU12/4.5

IEC 60947... IEC 60947...

Accessories:
(available separately)
z M12 connectors (KD …)
z Ready-made cables (KB …)
5-pin: KB-095-5000-5A

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 VSU 12/4.4(.5) - 03
[email protected] • www.leuze.com DB 18 UP.1 - 03
 VSU 12

Specifications Tables
Sensor data DB 18 UP VSU 12/4.4.../4.5
Operating range (recommended) 25mm
Operating range limit 20 … 40mm
Converter frequency 200kHz ± 2%
Sound cone approx. 12°
Timing
Web speed max. 1000m/min
min.≥ 6mm/s
(with 30mm splice width)
Recovery-time constant (LED A flashes path clear/
briefly) inserted medium < 5s
Delay before start-up ≤ 100ms
Pulse stretching 0 … 200ms, adjustable
Electrical data
Operating voltage UB 10 … 30VDC
(incl. residual ripple)
Residual ripple ≤ 15% of UB
Bias current ≤ 75mA
Outputs
Tape PNP transistor output
Function forced tripping of transistor
when splice detected
Level under limit PNP transistor output
Function forced tripping of transistor
when material not detectable
VSU 12/4.5
Web material (paper tear) PNP transistor output Diagrams
Function forced tripping of transistor
Splice width in dependence of web speed
when material present between
the sensors 70
Signal voltage high/low ≥ (UB -2V)/≤ 2V
60
Output current max. 200mA per output

Splice width [mm]

50
Indicators 40
VSU 12/4.4 30
LED B green foil selected 20
LED D green paper selected 10
LED C yellow splice detected 0
LED A red flashing material not detectable 0 10 20 30 40
Web speed [m/s]
VSU 12/4.5
LED A red flashing material not detectable
LED A yellow paper tear
Mechanical data
Housing nickel-faced brass aluminum, powder coated black
Weight 30g 400g
Connection type M8 connector, 3-pin, with M12 connector,
2m cable 5-pin
Environmental data
Ambient temp. (operation/storage) 0°C … +60°C/-40°C … +70°C
Protective circuit 1) 1,2,3
VDE safety class III
Protection class IP 65
Standards applied EN 60947-5-2
Options Note
Commutation input Paper/Foil 2)
Paper mode 0V or not connected
Foil mode ≥ 8V
1) 1=transient protection, 2=polarity reversal protection, 3=short circuit protection
2) Switch S1 must be in position 0 "Paper"

Order guide
Designation Part No.
Sensor pair DB 18 UP.1-25, 2500 501 08998

Amplifier VSU 12/4.4 501 04022

VSU 12/4.5 501 04139

VSU 12/4.4(.5) - 03 0904

DB 18 UP.1 - 03
VSU 12

Technical description

General
The ultrasonic system for splice detection consists of a VSU 12/4… evaluation amplifier and a DB 18 UP ultrasonic sensor pair.
It mainly detects splices on paper, plastic or metal web used on roll machines.

Mounting
Transmitter and receiver (DB 18 UP) have the same construction and are to be mounted at an angle of 65° (± 2°) relative to the
sheet.
The distance between transmitter and receiver should be 25mm (± 5mm).
Exact alignment (± 1°) must be ensured. Alignment which is not in line with the axis results in a reduction of the working range.
The material to be scanned must be located approx. 8 … 10mm above the transmitter.
The pitch of the sensors should be parallel to the tape or, as the case may be, splices.

Function
The evaluation unit can be operated in two different modes.

a) Parameter switch S1 in position "0" (paper)

The sheet is either paper or cardboard.

b) Parameter switch S1 in position "1" (foil)

The sheet is either plastic or metalised foil.
The amplifier has a higher sensitivity.

The changeover from "paper" to "foil" can also be performed via PIN 5 "Paper/Foil". Low-level on connection 5 means "paper",
high-level (≥ 8V) on connection 5 means "foil". The parameter switch S1 must be in position 0 "paper" in order to use this feature
(state on delivery).

Adjusting the sensitivity (P2)

Inhomogeneities in the web material may lead to erroneous switching in the detection of glued seams. These faults may generate
signals even if there is no glued seam. By lowering the sensitivity via the potentiometer P2 (turn left), this erroneous switching
may be alleviated. Full right turn position on P2 corresponds to maximum sensitivity (factory setting).

Operation VSU 12/4.4

The VSU 12/4.4 evaluation unit automatically adapts to the acoustic transmissivity of the medium. As soon as a splice is detected,
the "splice detected" output (tape) is triggered. The duration of the output signal can be set via the potentiometer (pulse stretch-
ing) P1. The maximum time which can be set is 200ms. A detected splice is indicated on LED C.
If the level is not sufficient for reliable detection, the "Material not detectable" output (Level under Limit) is triggered. This is also
signalled via the red flashing LED A.
Operation VSU 12/4.5
The VSU 12/4.5 evaluation unit automatically adapts to the acoustic transmissivity of the medium. As soon as a splice is detected,
the "splice detected" output (tape) is triggered. The duration of the output signal can be set via the potentiometer (pulse stretch-
ing) P1. The maximum time which can be set is 200ms. A detected splice is indicated on LED C.
If the level is not adequate for reliable detection, this is indicated by the red, flashing LED A. As soon as the system detects a
paper tear or if no material is present between the sensors, this is indicated at PIN 2 via the PNP output.

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 VSU 12/4.4(.5) - 03
[email protected] • www.leuze.com DB 18 UP.1 - 03
 VSU 12

Controls and indicators

Display
(see Specifications)

A Red LED
Adjustment
B Green LED
(see Specifications)
C Yellow LED
D Green LED

P1 Potentiometer
0 … 200ms pulse stretching
P2 Potentiometer
sensitivity adjustment
S1 Foil/Paper switch
0 = paper
1 = foil

Mounting and notes

Note
z When aligning the sender
and receiver, the best possi-
ble alignment must be
ensured.
z For proper function, the sen-
sors must be positioned at
an angle of F = 65° (± 2°) rel-
A Receiver
ative to the web.
B Outer edge
C Tape min. 15mm wide
D Paper or foil web
E Transmitter
F Pitch relative to the direction of travel

A Receiver
B Holder
C Transmitter
D Paper or foil web
E Direction of travel
F Splice

VSU 12/4.4(.5) - 03 0904

DB 18 UP.1 - 03