SFP 1G SX 31 T02#151011

SFP-1G-SX-31-T02#151011
1Gbps 1310nm 2km SX SFP Optical Transceiver
Product 1Gbps 1310nm 2km SX SFP Optical Transceiver
Model SFP-1G-SX-31-T02
File No. SFP-1G-SX-31-T02#151011
Version 1.0
Issuing Date 2019-12-19
Specification Revision Record

Date Version Page Revision Description Prepare Approve
20200928 1.0 Deng SC
All right reserved by Guilin GLsun Science and Tech Group Co., LTD. Without written permission,
-1-
any unit or individual can’t reproduce, copy or use it for any commercial purpose.
Guilin GLsun Science and Tech Group Co., LTD.

-1-
Tel: +86-773-3116006 [email protected] Web: www.glsun.com
SFP-1G-SX-31-T02#151011
Product Description
SFP-1G-SX-31-T02 SFP transceivers are high performance, cost effective modules supporting dual
data-rate of 1.25Gbps/1.0625Gbps and 2km transmission distance with MMF.The transceiver consists of
three sections: a FP laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier
(TIA) and MCU control unit. All modules satisfy class I laser safety requirements.The transceivers are
compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to
SFP MSA.
Product Feature
Supports 1.25Gbps/1.0625Gbps bit rates

Duplex LC connector
Hot pluggable SFP footprint
1310nm FP laser transmitter and PIN photo-detector
Applicable for 2Km MMF connection
Low power consumption, < 0.8W
Digital Diagnostic Monitor Interface
Compliant with SFP MSA and SFF-8472
Very low EMI and excellent ESD protection
Operating case temperature:
Commercial: 0 to 70 °C
Industrial: -40 to 85 °C
Applications
Gigabit Ethernet
Fiber Channel
Switch to Switch interface
Switched backplane applications
Router/Server interface
Other optical transmission systems
Functional Diagram

-2-
SFP-1G-SX-31-T02#151011
Absolute Maximum Rating
Parameter Symbol Min Max Unit Note

Supply Voltage Vcc -0.5 4.0 V
Storage Temperature TS -40 85 °C
Relative Humidity RH 0 85 %
Note: Stress in excess of the maximum absolute ratings can cause permanent damage to the transceiver.
General Operating Characteristics
Parameter Symbol Min Typ Max Unit Note

Data Rate DR 1.0625 1.25 Gb/s
Supply Voltage Vcc 3.13 3.3 3.47 V
Supply Current Icc5 220 mA
Tc 0 70
Operating Case Temp. °C
TI -40 85
Electrical Characteristics (TOP(C) = 0 to 70 °C, TOP(I) =-40 to 85 °C,VCC = 3.13 to 3.47 V)

Transmitter
Differential data input swing VIN,PP 120 820 mVpp 1
Tx Disable Input-High VIH 2.0 Vcc+0.3 V
Tx Disable Input-Low VIL 0 0.8 V
Tx Fault Output-High VOH 2.0 Vcc+0.3 V 2
Tx Fault Output-Low VOL 0 0.5 V 2
Input differential impedance Rin 100 Ω
Receiver
Differential data output swing Vout,pp 300 650 800 mVpp 3
Rx LOS Output-High VROH 2.0 Vcc+0.3 V 2
Rx LOS Output-Low VROL 0 0.8 V 2
Notes:
1. TD+/- are internally AC coupled with 100Ω differential termination inside the module.
2. Tx Fault and Rx LOS are open collector outputs, which should be pulled up with 4.7k to 10kΩ
resistors on the host board. Pull up voltage between 2.0V and Vcc+0.3V.
3. RD+/- outputs are internally AC coupled, and should be terminated with 100Ω (differential) at the user
SERDES

-3-
SFP-1G-SX-31-T02#151011
Optical Characteristics (TOP(C) = 0 to 70°C, TOP(I) =-40 to 85°C, VCC = 3.13 to 3.47 V)

Transmitter
Operating Wavelength λ 1270 1310 1360 nm
Ave. output power (Enabled) PAVE -9 -3 dBm 1
Extinction Ratio ER 9 dB 1
RMS spectral width Δλ 5 nm
Rise/Fall time (20%~80%) Tr/Tf 0.26 ns 2
Dispersion penalty TDP 3.9 dB
Output Optical Eye IEEE802.3ah-2004 Compliant
Receiver
Operating Wavelength λ 1260 1610 nm
Receiver Sensitivity PSEN1 -21 dBm 3
Overload PAVE -3 dBm 3
LOS Assert Pa -35 dBm

LOS De-assert Pd -22 dBm
LOS Hysteresis Pd-Pa 0.5 dB

LOS Hysteresis 0.5 5 dB
Notes:
1. Measured at 1.25Gb/s with PRBS 2 223–1 NRZ test pattern
2. Unfiltered, measured with a PRBS 2 223–1 test pattern @1.25Gbps
3. Measured at 1.25Gb/s with PRBS 223 – 1 NRZ test pattern for BER < 1x10-12
Pin Definition And Functions

-4-
SFP-1G-SX-31-T02#151011
Pin Symbol Name/Description Notes

1 VeeT Tx ground
2 Tx Fault Tx fault indication, Open Collector Output, active “H” 1
3 Tx Disable LVTTL Input, internal pull-up, Tx disabled on “H” 2
4 MOD-DEF2 2 wire serial interface data input/output (SDA) 3
5 MOD-DEF1 2 wire serial interface clock input (SCL) 3
6 MOD-DEF0 Model present indication 3
7 Rate select No connection
8 LOS Rx loss of signal, Open Collector Output, active “H” 4
9 VeeR Rx ground
10 VeeR Rx ground
11 VeeR Rx ground
12 RD- Inverse received data out 5
13 RD+ Received data out 5
14 VeeR Rx ground
15 VccR Rx power supply
16 VccT Tx power supply
17 VeeT Tx ground
18 TD+ Transmit data in 6
19 TD- Inverse transmit data in 6
20 VeeT Tx ground
Notes:
1. When high, this output indicates a laser fault of some kind. Low indicates normal operation. And should
be pulled up with a 4.7 – 10KΩ resistor on the host board.
2. TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the
module with a 4.7 – 10KΩ resistor. Its states are:
Low (0 – 0.8V): Transmitter on (>0.8, < 2.0V): Undefined
High (2.0V~Vcc+0.3V): Transmitter Disabled Open: Transmitter Disabled
3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10KΩ
resistor on the host board. The pull-up voltage shall be between 2.0V~Vcc+0.3V.
Mod-Def 0 has been grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
4. When high, this output indicates loss of signal (LOS). Low indicates normal operation
5. RD+/-: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which
should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the
module and is thus not required on the host board.
6. D+/-: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω
differential termination inside the module. The AC coupling is done inside the module and is thus not
required on the host board
-5-
SFP-1G-SX-31-T02#151011
Digital Diagnostic Specifications
The SFP-1G-SX-31-T02 SFP transceivers can be used in host systems that require either internally or
externally calibrated digital diagnostics.
Parameter Symbol Unit Min Max Accuracy Note

Transceiver temperature DTemp-E ºC -45 +90 ±5ºC 1
Transceiver supply voltage DVoltage V 2.8 4.0 ±3%
Transmitter bias current DBias mA 2 15 ±10% 2
Transmitter output power DTx-Power dBm -12 0 ±3dB
Receiver average input power DRx-Power dBm -24 0 ±3dB
Notes:
1. When Operating temp.=0~70 ºC,the range will be min=-5,Max=+75
2. The accuracy of the Tx bias current is 10% of the actual current from the laser driver to the laser
3. Internal/ External Calibration compatible.
Typical Interface Circuit

-6-
SFP-1G-SX-31-T02#151011
Package Dimensions
Ordering information
Part Number Operating Case temperature DDMI
SFP-1G-SX-31-T02 Commercial (0~70°C) Yes

-7-

SFP 1G SX 31 T02#151011

Uploaded by

Copyright:

Available Formats

SFP 1G SX 31 T02#151011

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SFP 1G SX 31 T02#151011

Uploaded by

Copyright:

Available Formats

SFP-1G-SX-31-T02#151011

1Gbps 1310nm 2km SX SFP Optical Transceiver

Product 1Gbps 1310nm 2km SX SFP Optical Transceiver

File No. SFP-1G-SX-31-T02#151011

Issuing Date 2019-12-19

Specification Revision Record

20200928 1.0 Deng SC

Guilin GLsun Science and Tech Group Co., LTD.

Supports 1.25Gbps/1.0625Gbps bit rates

Guilin GLsun Science and Tech Group Co., LTD.

Absolute Maximum Rating

Parameter Symbol Min Max Unit Note

General Operating Characteristics

Parameter Symbol Min Typ Max Unit Note

Electrical Characteristics (TOP(C) = 0 to 70 °C, TOP(I) =-40 to 85 °C,VCC = 3.13 to 3.47 V)

Parameter Symbol Min Typ Max Unit Note

Guilin GLsun Science and Tech Group Co., LTD.

Parameter Symbol Min Typ Max Unit Note

Ave. output power (Enabled) PAVE -9 -3 dBm 1

Overload PAVE -3 dBm 3

LOS Assert Pa -35 dBm

LOS Hysteresis Pd-Pa 0.5 dB

Pin Definition And Functions

Guilin GLsun Science and Tech Group Co., LTD.

Pin Symbol Name/Description Notes

Digital Diagnostic Specifications

Parameter Symbol Unit Min Max Accuracy Note

Transceiver supply voltage DVoltage V 2.8 4.0 ±3%

Transmitter bias current DBias mA 2 15 ±10% 2

Transmitter output power DTx-Power dBm -12 0 ±3dB

Receiver average input power DRx-Power dBm -24 0 ±3dB

Typical Interface Circuit

Guilin GLsun Science and Tech Group Co., LTD.

Part Number Operating Case temperature DDMI

SFP-1G-SX-31-T02 Commercial (0~70°C) Yes

Guilin GLsun Science and Tech Group Co., LTD.

You might also like