RV3-65D-R4-V2: General Specifications

Download as pdf or txt
Download as pdf or txt
You are on page 1of 5

RV3-65D-R4-V2

8-port sector antenna, 2x 694–960 and 6x 1695–2690 MHz, 65°


HPBW, 4x IntRET
All Internal RET actuators are connected in “Cascaded SRET” configuration
Supports re-configurable antenna sharing capability enabling control of the internal RET
system using up to two separate RET compatible OEM radios

General Specifications
Antenna Type Sector

Band Multiband

Grounding Type RF connector inner conductor and body grounded to reflector and
mounting bracket

Performance Note Outdoor usage    |   Wind loading figures are validated by wind tunnel
measurements described in white paper WP-112534-EN

RF Connector Interface 7-16 DIN Female

RF Connector Location Bottom

RF Connector Quantity, high band 6

RF Connector Quantity, low band 2

RF Connector Quantity, total 8

Remote Electrical Tilt (RET) Information, General


RET Hardware CommRET v2

RET Interface 8-pin DIN Female    |   8-pin DIN Male

RET Interface, quantity 2 female    |   2 male

Dimensions
Width 350 mm   |   13.78 in

Length 2688 mm   |   105.827 in

Depth 208 mm   |   8.189 in

Array Layout

Page 1 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: February 5, 2020
RV3-65D-R4-V2

Port Configuration

Page 2 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: February 5, 2020
RV3-65D-R4-V2

Electrical Specifications
Operating Frequency Band 1695 – 2690 MHz    |   694 – 960 MHz

Total Input Power, maximum 800 W @ 50 °C

Remote Electrical Tilt (RET) Information, Electrical


Protocol 3GPP/AISG 2.0 (Single RET)

Power Consumption, idle state, maximum 1W

Power Consumption, normal conditions, maximum 8W

Input Voltage 10–30 Vdc

Internal RET High band (3)    |   Low band (1)

Electrical Specifications
Page 3 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: February 5, 2020
RV3-65D-R4-V2
Frequency Band, MHz 694–790 790–890 890–960 1695–1920 1920–2200 2300–2500 2500–2690
Gain, dBi 16.5 17.3 17.4 17 17.5 18.2 18.2
Beamwidth, Horizontal, 67 64 61 63 63 63 62
degrees
Beamwidth, Vertical, degrees 8.2 7.4 6.8 7.3 6.4 5.6 5.3
Beam Tilt, degrees 0–10 0–10 0–10 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 18 24 23 16 17 16 16
Front-to-Back Ratio at 180°, 31 33 34 35 37 37 37
dB
Isolation, Cross Polarization, 28 28 28 28 28 28 28
dB
Isolation, Inter-band, dB 30 30 30 30 30 30 30
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0

PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50° 250 250 250 200 200 200 200
C, maximum, watts

Electrical Specifications, BASTA


Frequency Band, MHz 694–790 790–890 890–960 1695–1920 1920–2200 2300–2500 2500–2690
Gain by all Beam Tilts, 16.3 17 17.3 16.5 17.1 17.8 17.7
average, dBi
Gain by all Beam Tilts ±0.3 ±0.4 ±0.3 ±0.8 ±0.6 ±0.6 ±0.6
Tolerance, dB
Gain by Beam Tilt, average, 0 ° | 16.1 0 ° | 16.7 0 ° | 17.1 2 ° | 16.3 2 ° | 16.8 2 ° | 17.3 2 ° | 17.4
dBi 5 ° | 16.4 5 ° | 17.0 5 ° | 17.4 6 ° | 16.6 6 ° | 17.2 6 ° | 17.9 6 ° | 17.9
10 ° | 16.3 10 ° | 17.0 10 ° | 17.3 12 ° | 16.4 12 ° | 17.1 12 ° | 17.7 12 ° | 17.4

Beamwidth, Horizontal ±1.1 ±1.9 ±1.4 ±3.9 ±2.7 ±3.4 ±3.5


Tolerance, degrees
Beamwidth, Vertical ±0.4 ±0.4 ±0.3 ±0.6 ±0.5 ±0.3 ±0.3
Tolerance, degrees
USLS, beampeak to 20° 15 17 18 12 14 13 12
above beampeak, dB
Front-to-Back Total Power at 26 25 25 28 28 29 28
180° ± 30°, dB
CPR at Boresight, dB 17 20 21 18 20 19 17
CPR at Sector, dB 11 10 10 11 11 7 7

Material Specifications
Radiator Material Aluminum    |   Low loss circuit board

Radome Material Fiberglass, UV resistant

Reflector Material Aluminum

Page 4 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: February 5, 2020
RV3-65D-R4-V2
Mechanical Specifications
Wind Loading at Velocity, frontal 107.2 lbf @ 150 km/h    |   477.0 N @ 150 km/h

Wind Loading at Velocity, lateral 409.0 N @ 150 km/h    |   91.9 lbf @ 150 km/h

Wind Loading at Velocity, maximum 1,010.0 N @ 50 km/h    |   227.1 lbf @ 50 km/h

Wind Speed, maximum 241 km/h   |   149.75 mph

Packaging and Weights


Width, packed 460 mm   |   18.11 in

Depth, packed 350 mm   |   13.78 in

Length, packed 2830 mm   |   111.417 in

Net Weight, without mounting kit 32.5 kg   |   71.65 lb

Weight, gross 46.5 kg   |   102.515 lb

Regulatory Compliance/Certifications
Agency Classification
CE Compliant with the relevant CE product directives
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system

Included Products
BSAMNT-4 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
bracket set and one bottom bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

Page 5 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: February 5, 2020

You might also like