Bs en 12390 7 Testing Hardened Concrete Part 7 Density of Hardened

BRITISH STANDARD BS EN
12390-7:2000
Incorporating
Corrigendum No.1
Testing hardened
concrete —
Part 7: Density of hardened concrete
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
The European Standard EN 12390-7:2000 has the status of a

British Standard
ICS 91.100.30
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
Copyright British Standards Institution
Provided by IHS under license with BSI - Uncontrolled Copy Licensee=GHKSAR - Architectural Svc Dept/5905334001
No reproduction or networking permitted without license from IHS Not for Resale, 12/05/2006 20:23:59 MST
BS EN 12390-7:2000
National foreword
This British Standard is the official English language version of
EN 12390-7:2000, including Corrigendum September 2004. It will supersede
BS 1881-114:1983, which will be withdrawn in 2003 when the full package of
concrete standards is available.
The UK participation in its preparation was entrusted by Technical Committee
B/517, Concrete, to Subcommittee B/517/1, Concrete production and testing,
which has the responsibility to:
— aid enquirers to understand the text;
— present to the responsible international/European committee any

enquiries on the interpretation, or proposals for change, and keep the
UK interests informed;
— monitor related international and European developments and
promulgate them in the UK.
A list of organizations represented on this subcommittee can be obtained on

request to its secretary.
Cross-references
The British Standards which implement international or European
publications referred to in this document may be found in the BSI Catalogue
under the section entitled “International Standards Correspondence Index”, or
by using the “Search” facility of the BSI Electronic Catalogue or of
British Standards Online.
This publication does not purport to include all the necessary provisions of a
contract. Users are responsible for its correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, the EN title page,
pages 2 to 9 and a back cover.
The BSI copyright notice displayed in this document indicates when the
This British Standard, having document was last issued.
been prepared under the
direction of the Sector
Committee for Building and
Civil Engineering, was Amendments issued since publication
published under the authority
of the Standards Committee
and comes into effect on
Amd. No. Date Comments
15 December 2000
15440 12 November 2004 Changes to Clause 4
Corrigendum No.1
© BSI 12 November 2004
ISBN 0 580 36607 3

--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---

EUROPEAN STANDARD EN 12390-7
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2000
ICS 91.100.30 Incorporating corrigendum September 2004
English version
Testing hardened concrete - Part 7: Density of hardened

concrete
Essai pour béton durci - Partie 7: Masse volumique du Prüfung von Festbeton - Teil 7: Dichte von Festbeton
béton durci
This European Standard was approved by CEN on 18 February 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12390-7:2000 E
worldwide for CEN national Members.

Page 2
EN 12390-7:2000
Contents
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
Page
Foreword ............................................................................................................................................................................ 3
1 Scope ............................................................................................................................................................................ 3
2 Normative references ................................................................................................................................................. 4
3 Apparatus ..................................................................................................................................................................... 4
4 Test Specimens ........................................................................................................................................................... 4
5 Procedure ..................................................................................................................................................................... 4
6 Test result..................................................................................................................................................................... 8
7 Test report .................................................................................................................................................................... 8
8 Precision....................................................................................................................................................................... 8
Figure 1 - Typical stirrup arrangement for the determination of the volume of concrete
specimens by water displacement ................................................................................................................................. 7
Table 1 - Precision data for measurements of the saturated density of hardened concrete.................................. 9

Page 3
EN 12390-7:2000
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 104, Concrete (performance,
production, placing and compliance criteria), the Secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by April 2001, and conflicting national standards shall be withdrawn at the latest by
December 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries
are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France,
Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland
and the United Kingdom.
This standard is one of a series of methods for testing concrete.
It is based on the International Standard ISO 6275 - Concrete, hardened - Determination of density.
A draft for this standard was published in 1996 for CEN enquiry as prEN 12363. It was one of a series of individually
numbered test methods for fresh or hardened concrete. For convenience it has now been decided to combine these
separate draft standards into three new standards with separate parts for each method, as follows:
- Testing fresh concrete (EN 12350)
- Testing hardened concrete (EN 12390)
- Testing concrete in structures (EN 12504)
The series EN 12390 includes the following parts where the brackets give the numbers under which particular test
methods were published for CEN enquiry:
EN 12390 Testing hardened concrete -
Part 1: Shape, dimensions and other requirements of specimens and moulds (former prEN 12356:1996)
Part 2: Making and curing specimens for strength tests (former prEN 12379:1996)
Part 3: Compressive strength of test specimens (former prEN 12394:1996)
Part 4: Compressive strength - Specification for testing machines (former prEN 12390:1996)
Part 5: Flexural strength of test specimens (former prEN 12359:1996)
Part 6: Tensile splitting strength of test specimens (former prEN 12362:1996)
Part 7: Density of hardened concrete (former prEN 12363:1996)
Part 8: Depth of penetration of water under pressure (former prEN 12364:1996)
1 Scope
This standard specifies a method for determining the density of hardened concrete.
It is applicable to lightweight, normal-weight and heavy-weight concrete.
It differentiates between hardened concrete in the following states:
– as-received;
– water saturated;
– oven-dried.
The mass and the volume of the specimen of hardened concrete are determined and the density calculated.
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---

Page 4
EN 12390-7:2000
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 12390-1, Testing hardened concrete – Part 1: Shape, dimensions and other requirements of specimens and
moulds.
ISO 5725-1, Accuracy (trueness and precision) of measurement methods and results - Part 1: General principles and
definitions.
3 Apparatus
3.1 Callipers and rules, capable of determining the dimensions of a specimen to within ± 0,5 %.
3.2 Balance, equipped with a stirrup for weighing the specimen in both air and water to an accuracy of 0,1 % of
the mass.
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
3.3 Water tank, fitted with a device to maintain the water at a constant level and of sufficient size to allow the
specimen on the stirrup to be fully immersed to a constant depth.
3.4 Ventilated oven, in which the temperature is capable of being controlled at (105 ± 5) °C.
NOTE The apparatus required depends upon the method selected for determining the volume of the
specimen.
4 Test specimens
The minimum volume of a specimen shall be 0,785 l. If the nominal maximum aggregate size of specimens cast in
moulds exceeds 25 mm, the minimum volume shall be not less than 50 D3, where D is the nominal maximum size of
the coarse aggregate.
Normally, the entire specimen as received shall be used for the determination. If the shape or size of a specimen is
such that it is not possible to use all of it, a smaller specimen may be broken or sawn from the original.
Capped specimens shall not be used.
5 Procedures
5.1 General
5.1.1 Determination of mass
The standard recognizes three conditions under which the mass of a specimen can be determined:
a) as-received;
b) water saturated;
c) oven-dried.

Page 5
EN 12390-7:2000
5.1.2 Determination of volume
The standard recognizes three methods for determining the volume of the specimen:
a) by water displacement (reference method);
b) by calculation using actual measurements;
c) for cubes, by calculation, using checked, designated dimensions.
NOTE 1 The precision of the method depends on the method selected for measuring the volume of the
specimen. Measurement of volume by the water-displacement method is the most precise, followed by
calculation using measurement of actual dimensions and lastly calculation using checked, designated,
dimensions.
NOTE 2 The limitation to cubes in 5.1.2 c) of using designated dimensions in calculation of volume is due to
the greater tolerance on length, according to EN 12390-1, of other specimen shapes.
5.2 Mass of as-received specimen
Weigh the as-received specimen (mr), to an accuracy of 0,1 % of the mass of the specimen. Record the value
indicated, in kilograms.
5.3 Mass of water saturated specimen
Immerse the specimen in water at (20 ± 2) °C until the mass changes by less than 0,2 % in 24 h, wiping the surplus
water from the surface before each weighing. Record the value of the saturated mass (ms), in kilograms.
NOTE Specimens of concrete cured in water for at least 72 h prior to testing, may be assumed to be
saturated to a constant mass.
5.4 Mass of oven-dried specimen
Dry the specimen in a ventilated oven at (105 ± 5) °C until the mass changes by less than 0,2 % in 24 h. Before each
weighing, cool the specimen to near room temperature in a dry airtight vessel or desiccator. Record the value of the
oven-dried mass (mo) as indicated, in kilograms.
5.5 Volume obtained by water displacement
5.5.1 General
Ensure that the specimen is in a saturated condition.
NOTE 1 This method is suitable for specimens of all shapes and is the only method suitable for specimens of
irregular shape.
NOTE 2 This method is normally unsuitable for specimens of no-fines concrete, lightweight aggregate
concrete with large pores, or specimens whose moisture content must not to be altered. However, the
application of a thin water impermeable layer can make this method practicable.
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---

Page 6
EN 12390-7:2000
5.5.2 Mass in water
Determine the mass of the specimen in water according to the following procedure:
Raise the water tank until the stirrup, without a specimen, is immersed in the water tank and not touching the bottom
of the tank. Record the apparent mass of the stirrup (mst), in kilograms.
NOTE 1 The apparent mass of the stirrup may alternatively be allowed for using a zero setting facility on the
balance (tareing).
Place the specimen in the stirrup and raise the water tank until the specimen is submerged and the water level on the
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
stirrup is the same as it was without the specimen.
NOTE 2 Trapping of air bubbles on the sides of the specimen and on the stirrup should be avoided.
Record the apparent mass (mst + mw), in kilograms, of the immersed specimen and stirrup.
5.5.3 Mass in air
Determine the mass of the specimen in air according to the following procedure:
Remove the specimen from the stirrup and wipe the surplus water from the surfaces, using a damp cloth. Place the
specimen on the balance and record the mass of the specimen in air (ma) in kilograms.
5.5.4 Calculate the volume of the specimen
Calculate the volume of the specimen, using the formula :
- [( mst + m w ) - mst ]
V = ma
ρw
where:
V is the volume of the specimen, in cubic metres;
ma is the mass of the specimen in air, in kilograms;
mst is the apparent mass of the immersed stirrup, in kilograms;
mw is the apparent mass of the immersed specimen, in kilograms;
ρw is the density of water, at 20 °C, taken as 998 kg/m³.

Page 7
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
EN 12390-7:2000
a) Stirrup suspeded beneath b) Alternative form of stirrup suspended

balance mechanism above balance mechanism
Key
1 Balance
2 Stirrup
3 Concrete specimen
4 Guide
5 Water tank is moved vertically
6 Side view of stirrup
Figure 1 - Typical stirrup arrangement for the determination of the volume of concrete
specimens by water displacement
5.5.4 Volume obtained by measurement
Calculate the volume of the specimen from measurements made on the specimen in accordance with EN 12390-1, in
cubic metres, rounded to four significant figures.
5.5.5 Volume obtained by using designated dimensions (cubes only)
Confirm that the cube has been made in a calibrated mould, conforming to EN 12390-1.
Check the dimensions in accordance with EN 12390-1.
Calculate the volume of the cube in cubic metres, expressed to 3 significant figures.

Page 8
EN 12390-7:2000
6 Test result
Calculate the density using the values determined for the mass of specimen and its volume, using the formula:
m
D=
V
where:
D is the density related to the condition of the specimen and the method of determining the volume, in
kilograms per cubic metre;
m is the mass of the specimen in its condition at the time of test, in kilograms;
V is the volume determined by the particular method, in cubic metres.
Report the condition of the specimen at the time of test and the method used for determining the volume of the
specimen as part of the test result.
Express the result of the density determination to the nearest 10 kg/m³.
7 Test report
The report shall include:
a) identification of the test specimen;
b) location of performance of test;
c) description of the specimen (e.g. 100 mm cube, 150 mm diameter core);
d) details of specimen preparation (if any);
e) condition of specimen at time of test; (as-received, or water saturated, or oven-dried);
f) method of determination of volume; (water displacement, or measured size, or checked, designated size);
g) date of test;
h) calculated density of specimen;
i) any deviation from standard test methods;
j) a declaration by the person technically responsible for the test that it was carried out in accordance with this
standard, except as noted in item i).
8 Precision
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---
Precision data are given in Table 1. These apply to density measurements in the range 2 300 kg/m3 to 2 400 kg/m3
on cubes made from the same sample of concrete and when each test result is obtained from a single determination
of the saturated density of a single cube. They indicate the variability that occurs when sampling, making and curing
the cubes.

Page 9
EN 12390-7:2000
Table 1 - Precision data for measurements of the saturated density of hardened concrete
Test method Repeatability conditions Reproducibility conditions

sr r sR R
3 3 3
kg/m kg/m kg/m kg/m3
By calculation using
measured dimensions:
100 mm cubes, 13,9 39 20,5 57
150 mm cubes. 9,9 28 20,5 57
By water displacement:
100 mm cubes
150 mm cubes 6,5 18 12,8 36
6,4 18 10,6 30
NOTE 1 The precision data were determined as part of an experiment carried out in
1987 in which precision data were obtained for several of the tests described in
BS 1881. The experiment involved 16 operators. The concretes were made using an
ordinary Portland cement, Thames Valley sand, and Thames Valley 10 mm and
20 mm coarse aggregates.
NOTE 2 The difference between two test results from the same sample by one
operator using the same apparatus within the shortest feasible time interval will
exceed the repeatability value r on average not more than once in 20 cases in the
normal and correct operation of the method.
NOTE 3 Test results on the same sample obtained within the shortest feasible time
interval by two operators each using their own apparatus will differ by the
reproducibility value R on average not more than once in 20 cases in the normal and
correct operation of the method.
NOTE 4 For further information on precision, and for definitions of the statistical
terms used in connection with precision, see ISO 5725-1.
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---

BS EN
12390-7:2000
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL
--`,``,`,`,,`,,`,`,``,,,```,`,`-`-`,,`,,`,`,,`---


Bs en 12390 7 Testing Hardened Concrete Part 7 Density of Hardened

Uploaded by

Copyright:

Available Formats

Bs en 12390 7 Testing Hardened Concrete Part 7 Density of Hardened

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bs en 12390 7 Testing Hardened Concrete Part 7 Density of Hardened

Uploaded by

Copyright:

Available Formats

BRITISH STANDARD BS EN

The European Standard EN 12390-7:2000 has the status of a

— aid enquirers to understand the text;

— present to the responsible international/European committee any

A list of organizations represented on this subcommittee can be obtained on

ISBN 0 580 36607 3

Copyright British Standards Institution

ICS 91.100.30 Incorporating corrigendum September 2004

Testing hardened concrete - Part 7: Density of hardened

This European Standard was approved by CEN on 18 February 2000.

EUROPEAN COMMITTEE FOR STANDARDIZATION

Management Centre: rue de Stassart, 36 B-1050 Brussels

Copyright British Standards Institution

2 Normative references ................................................................................................................................................. 4

4 Test Specimens ........................................................................................................................................................... 4

7 Test report .................................................................................................................................................................... 8

Copyright British Standards Institution

This standard is one of a series of methods for testing concrete.

- Testing fresh concrete (EN 12350)

- Testing hardened concrete (EN 12390)

- Testing concrete in structures (EN 12504)

EN 12390 Testing hardened concrete -

It is applicable to lightweight, normal-weight and heavy-weight concrete.

It differentiates between hardened concrete in the following states:

Copyright British Standards Institution

Capped specimens shall not be used.

5.1.1 Determination of mass

Copyright British Standards Institution

5.1.2 Determination of volume

a) by water displacement (reference method);

b) by calculation using actual measurements;

c) for cubes, by calculation, using checked, designated dimensions.

5.2 Mass of as-received specimen

5.3 Mass of water saturated specimen

5.4 Mass of oven-dried specimen

5.5 Volume obtained by water displacement

Ensure that the specimen is in a saturated condition.

Copyright British Standards Institution

5.5.2 Mass in water

stirrup is the same as it was without the specimen.

5.5.3 Mass in air

5.5.4 Calculate the volume of the specimen

Calculate the volume of the specimen, using the formula :

V is the volume of the specimen, in cubic metres;

ma is the mass of the specimen in air, in kilograms;

mst is the apparent mass of the immersed stirrup, in kilograms;

mw is the apparent mass of the immersed specimen, in kilograms;

ρw is the density of water, at 20 °C, taken as 998 kg/m³.

Copyright British Standards Institution

a) Stirrup suspeded beneath b) Alternative form of stirrup suspended

5.5.4 Volume obtained by measurement

5.5.5 Volume obtained by using designated dimensions (cubes only)

Check the dimensions in accordance with EN 12390-1.

Copyright British Standards Institution

V is the volume determined by the particular method, in cubic metres.

Express the result of the density determination to the nearest 10 kg/m³.

a) identification of the test specimen;

b) location of performance of test;

c) description of the specimen (e.g. 100 mm cube, 150 mm diameter core);

d) details of specimen preparation (if any);