The design and construction of facilities for handling cattle

The design and construction of facilities for handling cattle

T. Grandin
Animal Science Department, Colorado State University, Fort Collins, CO 80523, USA

Abstract

The cattle handling facilities described in this paper are recommended for use with extensively raised
cattle which have a large flight zone and are not completely tame. This paper contains diagrams and
designs for corrals, yards, sorting (drafting), handling and loading trucks. Single-file races, crowd pens,
restraint devices and truck loading ramps should have high solid sides to help keep the cattle calm.
Solid fences prevent the cattle from seeing moving people and other distractions outside the fence.
Cattle will move more easily through curved races because a curved race prevents the animals from
seeing people up ahead. Curved races must be laid out correctly to make them work efficiently. A
curved single-file race must not be bent too sharply where it joins the crowd pen. An animal standing
in the crowd pen must be able to see two or three body lengths up the singlefile race. Equipment for
restraining (fixation) of cattle for veterinary procedures should utilize three behavioral principles: 6)
blocking the animal's vision; 60 slow steady motion of parts of the apparatus which are pressed against
the animal; and (iii) optimal pressure. A restraint device must apply sufficient pressure to provide the
feeling of being held, but excessive pressure that causes pain or struggling must be avoided. Shadows,
sparkling reflections, high-pitch noise and objects which jiggle or move will cause cattle to balk and
impede movement through the race. C 1997 Published by Elsevier Science B.V. Keywords: Handling;
Sorting; Drafting; Restraint; Race; Cattle

1. Introduction

Well-designed facilities for veterinary work, loading trucks, sorting and other procedures will make
handling more efficient and help reduce stress and injuries. Reducing stress during handling is
important because handling stresses can lower conception rates (Hixon et al., 1981), suppress immune
function (Kelley et al., 1981; Blecha et al., 1984), and raise cortisol levels (Zavy et al., 1992). Rough
handling will reduce weight gains and increase shrink (Grandin (1980a)). Cattle handled quietly in well
designed facilities had much lower heart rates compared to cattle handled roughly in poor facilities
(Stermer et al., 1981). The amount of stress imposed upon an animal during handling is greatly
affected by its previous experiences (Grandin, 1984a, 1987a, 1993b and Fordyce, 1987). Cattle which
have been handled gently will be quieter and less agitated when they are handled in the future. Weaner
calves accustomed to regular gentle handling usually have less bruises during marketing because they
are accustomed to handling (Wythes and Shorthose, 1984). Animals remember aversive handling
experiences for at least a year (Hutson, 1985a). Good facilities will reduce bruises and carcass damage
on cattle and injuries to people. In the US, the cattle industry loses US$22 million annually from
bruises (Livestock Conservation Institute, no date). Bruise losses in New Zealand equal to 1% of the

http://grandin.com/references/design.construction.facilities.handling.cattle.html (1 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

country's annual export beef earnings (Marshall, 1977). Labor efficiency is greatly improved in good
facilities. One person can provide a continuous flow of cattle into the squeeze chute for vaccinations,
ear tagging and other procedures (Grandin, 1983a).

2. Cattle perception

Design of efficient handling facilities will be aided by an understanding of the behavioral

characteristics of livestock. Cattle have 360' wide angle vision (Prince, 1977). They can see behind
themselves without turning their heads and are sensitive to harsh contrasts of light and dark in loading
ramps, races and handling areas. To facilitate cattle movement, illumination should be even, and there
should be no sudden changes in floor level or texture. Even though ruminant animals have depth
perception (Lemmon and Patterson, 1964), their ability to perceive depth at ground level while moving
with their heads up is probably poor. Hutson 0985b) suggests that there may be an extensive blind area
at ground level and moving livestock may not be able to use motion parallax or retinal disparity cues to
perceive depth. To see depth on the ground, the animal would have to lower its head. This would
explain why cattle stop and balk at shadows. Cattle are more sensitive to high-pitch noises than people
(Kilgour et al., 1983). The sound of banging metal can cause balking and agitation. Rubber stops on
gates and squeeze chutes will help reduce noise. The pump and motor on a hydraulic squeeze chute
(crush) should be located away from the squeeze. On pneumatically powered equipment, silencing
devices must be installed. The sound of hissing air will agitate cattle.

3. How to prevent balking

A single shadow that falls across an alley or race can cause balking. The lead animal will often stop
and refuse to cross the shadow. Cattle will also balk at puddles of water, drain grates and bright spots
of sunlight. Drains should be placed outside of races

and crowd pens. Handlers should be cautious about causing moving shadows. Cattle have a tendency
to approach a more brightly illuminated area, provided the light is not glaring in their eyes. Lamps
directed toward the interior of a truck will facilitate loading at night. However, squeeze chutes and
loading ramps should not facing the sun because cattle will not approach blinding light.

Sometimes it is difficult to drive cattle under a roof or into a building for handling. The animals will
enter more readily if they are lined up in single file in a race (Grandin, 1980a). When a squeeze chute
is inside a building or under a shade, the single race should extend at least 3-5 m outside the shade.
Never place the edge of the shade or a building wall at the junction between the single-file race and the
crowd pen.

Cattle will also balk at moving or flapping objects. A coat flung over a fence or a shiny reflection off a
truck bumper may stop the movement of cattle. If the cattle see people standing in front of the squeeze
chute, they will refuse to approach. Installation of shields for handlers to stand behind may improve
cattle movement. It will be easier to observe the distractions that are causing balking when the cattle
are calm (Grandin, 1996). Problems with balking tend to come in bunches. When one animal balks, the
tendency to balk spreads to the next animal in line. An animal must never be prodded until it has an
opening to move into. Cattle can be easily moved in large pens with a piece of cloth or a plastic tied to

http://grandin.com/references/design.construction.facilities.handling.cattle.html (2 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

a stick (Grandin, 1993a). The animals will move away from the rustling plastic or the flapping cloth.
Dogs should only be used in open areas where there is sufficient space for the cattle to move away.
When dogs bite livestock, it is highly stressful (Kilgour and DeLangen, 1970).

4. Solid fences

The sides of the single-file race, loading ramp, and crowd pen should be solid (Grandin, 1980a, 1987a).
The crowd gate should also be solid to prevent cattle from attempting to turn back and rejoin their herd
mates. The principle of solid fences is like putting blinkers on a harness horse. The solid fences prevent
the cattle from seeing people, vehicles and other distractions outside the fence with their wide-angle
vision. Solid race sides will help prevent wild cattle from becoming highly agitated in a race (Fig. 1).
Observations in a race with a solid and an open-sided portion indicated that some wild cattle are much
more agitated in the portion of the race where they could see out. The cattle should see only one
pathway of escape, up the single-file race. They will balk if the race entrance appears to be a dead end.
Sliding or one-way gates at the junction between the single-file race and the crowd pen must be
constructed from bars or mesh so that cattle can see through them. However, a gate which is used in a
single-file race for stopping cattle movement during sorting or dipping should be solid to prevent
excited animals from attempting to push through it. All other races and forcing pen fences should be
solid.

On steel corrals, it would be too expensive to construct all the holding pens, sorting pens and alleys
with completely solid fences. On fences built from pipe or rod, a 30-60 cm-wide belly rail placed at
cow eye height will facilitate movement and will prevent the ramming of the fence by excited cattle.
This is especially important in facilities where wild Brahman, Brahman cross and Zebu cattle are
handled because Brahman-type cattle are more excitable and difficult to block at gates (Tulloh, 1961).
A belly rail is also recommended for handling excitable genetic lines of European continental cattle.
Corrals constructed from wide wood planks do not need an additional belly rail because the boards
create a substantial visual barrier.

5. Flight zone

When a person enters an animal's flight zone it will move away. If the handler penetrates the flight
zone too deeply, the animal will either bolt and run away or turn back and run past the person. When
the flight zone of a group of bulls was invaded by a mechanical trolley, the bulls moved away and
maintained a constant distance between themselves and the trolley (Kilgour, 1971). The best place for
the person to work is on the edge of the flight zone (Grandin, 1980a). This will cause the cattle to
move away in an orderly manner. The animals will stop moving when the handler retreats from the
flight zone. To make an animal move forward, the handler must be positioned behind the point of
balance at the shoulder (Kilgour and Dalton, 1984).

http://grandin.com/references/design.construction.facilities.handling.cattle.html (3 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 1. Well-designed curved single-file race with solid sides and a walkway along the inner
radius for the handler.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (4 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 2. Correct handler positions for driving cattle. The handler should remain on the boundary
of the flight zone for most efficient cattle movement. He moves from position A to position B to
make the animal move forward. From Grandin, 1980a.

The size of the flight zone varies depending on the tameness or wildness of the cattle. The flight zone
for extensively raised cows may be as much as 50 m, whereas the flight zone of feedlot cattle may be 2-
8 m. The edge of the flight zone can be determined by slowly walking up to the animals. The circle in
Fig. 2 represents the edge of the flight zone. Extremely tame cattle are often difficult to drive because
they no longer have a flight zone. The size of the enclosure in which the livestock are confined in may
affect the size of the flight zone. Sheep experiments indicated that animals confined in a narrow alley
had a smaller flight zone compared to animals confined in a wider alley (Hutson, 1982). Flight distance
is also affected by previous experience. Cattle with previous experiences with gentle handling will
have a smaller flight distance than cattle which have been handled roughly, and animals raised
intensively in buildings in close contact with people will have a smaller flight distance than extensively
raised range cattle.

Many people make the mistake of deeply invading the flight zone when cattle are being driven down
an alley or into an enclosed area such as a crowd pen. If the cattle attempt to turn back, the person
should back up and retreat from inside the flight zone. The cattle attempt to turn back because they are
trying to escape from the person inside their flight zones. Cattle sometimes rear up and become

http://grandin.com/references/design.construction.facilities.handling.cattle.html (5 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

agitated while waiting in a single-file race. A common cause of this problem is a person leaning over
the race and deeply penetrating the flight zone (Grandin, 1983a). The animal will usually settle back
down if the person backs up and retreats from the flight zone.

6. Curved race more efficient

A curved race is more efficient than a straight race for two reasons. First, it prevents the cattle from
seeing the truck or squeeze chute until they are almost in it. A curved race also takes advantage of the
animal's tendency to circle around the handler (Grandin, 1980a). Cattle will face a handler who enters
their pen. As the handler moves through the pen, the animals will circle around him. A curved race
takes advantage of the natural tendency to circle around a person. A curved race provides the greatest
advantage when the cattle have to wait in line for vaccination or other procedures. Experiments with
continuously moving livestock indicated no significant difference between straight and curved races
for run-through time (Vowles et al., 1984a). However, when a curved race with a round crowd pen is
used in a practical situation with the livestock lined up and waiting to enter a squeeze chute, the curved
system is faster (Vowles and Hollier, 1982). Circular crowding pens and curved races can reduce the
time spent in moving cattle by up to 50% (Vowles and Hollier, 1982).

Cattle can be driven most efficiently if the handler is situated at a 45-60' angle to the animal's shoulder
(Fig. 2). A well designed curved race has a walkway for the handler along the inner radius (Fig. 1). The
handler is forced to stand in the correct position to facilitate animal movement. The curved lines on
Fig. 2 represent the curved race. The solid fences in Fig. I block out all visual distractions except for
the handler on the catwalk.

In Australia and South America, cattle are often given veterinary treatment in the single-file race,
whereas in the US, Canada and many European countries, the animals are treated while held in a
squeeze chute (crush) or head gate (stanchion) at the end of the race. In a South American or
Australian operation, completely solid race sides would block access to the cattle. In this situation, the
outer fence should be completely solid and the fence on the inside radius should be constructed from
pipe or wood planks with spaces between them. The handler walkway is omitted. To prevent leg
injuries, the inner radius fence should have a 60 cm high solid panel at the bottom. In curved race
systems with completely solid sides, the handler walkway should run alongside the race and never be
placed overhead. The distance from the walkway platform to the top of the race fence should be 100
cm.

7. Curved race and crowd pen dimensions

For feedlot and range cattle handling facilities, the recommended inside radius for a curved race is 3.5-
6 m (Grandin, 1980a; Vowles and Hollier, 1982). A single-file race must be long enough to take
advantage of cattle following behavior. The minimum length for a race used for handling large
numbers of cattle is 9 m (Grandin, 1983a). A half circle race with a 3.5-5 m inner radius is the ideal
length. Excessively long races are not recommended because some cattle have a tendency to lie down
and get trampled if they are held too long in a race. The longer race with the 6 m inside radius is
recommended when cattle are vaccinated rapidly while held in the race. When a race is designed, care
must be taken to avoid bending the race sharply at the junction between the single-file race and the

http://grandin.com/references/design.construction.facilities.handling.cattle.html (6 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

crowd pen. A sharp bend at this point will make the entrance to the race appear to be a dead end. The
cattle will balk and may refuse to enter. An animal standing in the crowd pen must be able to see a
minimum of two body lengths up the single-file race.

Curved races can be built from wood, steel or concrete. When wood or concrete is used, the race can
be built in a series of straight sections (Fig. 3). The posts should be spaced 1.2 m apart. To reduce
construction costs, the race in Fig. 3 has a single board for a person to step on to prod cattle. For large
numbers of cattle, a complete handler walkway should be constructed.

Fig. 3. Curved wood, wide curved lane with solid sides which leads to the round forcing pen.

If space is restricted, a race with an inner radius as small as 1.5 m can be used if certain rules are
followed (Grandin, 1984b). When the inner radius is shorter than 3 m, the race must have a minimum
of a 3 m-long straight section joining the race to the crowd pen. This prevents the race from appearing
to be a dead end. A race with a very short inner radius must be built in a continuous smooth curve.
Cattle will get stuck if it is built in a series of straight sections. The recommended race width for a race
with straight sides is 66-71 cm for adult cows and 51 cm for calves. These dimensions may vary
depending on cow size. A V-shaped race should be 41-45 cm wide at the bottom and 81 cm wide at the
152 cm level. A common mistake is to make the race too wide. There should only be 2 cm of clearance
on each side of the largest cow which will use the race. Fence height for races, crowd pens and corrals
is 152 cm for English breeds and tame cattle, and 167-183 cm for Brahman, Brahman cross, Zebu

http://grandin.com/references/design.construction.facilities.handling.cattle.html (7 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

excitable genetic lines of European continental or wild cattle.

Fig. 4. Basic cattle handling system with curved race, round crowd pen and curved lane.

Fig. 4 illustrates a curved race, round crowd (forcing) pen and a wide curved lane. The crowd pen has
solid fences and is equipped with a crowd gate which can be advanced behind the cattle. This gate
should be solid. The wide curved lane holds cattle which are waiting to go into the crowd pen. A single
person can easily move them into the crowd pen by working along the inner radius of the 3.5 m wide
lane. This basic layout can be used on ranches, in feedlots for the main cattle handling facility, and in
slaughter plants. For small handling facilities on farms or feedlot hospitals, the wide curved lane can be
deleted and the round crowd pen can be connected directly to existing alleys. Fig. 4 is designed for
easy layout. It consists of three half circles which are located along the dotted line on Fig. 4. If the
crowd pen is constructed from wood, the fence can be built in a series of straight sections with 1.2 m
post-spacing. The ideal length for the crowd gate is 3.5 m. A longer gate is unwieldy and a larger
crowd pen is inefficient because it holds too many cattle. For smaller operations, the gate length can be
reduced to 3 m.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (8 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 5. Well-designed round crowd pen with solid fences and a solid crowd gate.

Fig. 5 illustrates a well designed round crowd pen with solid fences, solid crowd gate and a walkway
for the handler. The handler can advance the crowd gate as he walks along the walkway. This crowd
pen can be used to direct cattle into a single-file race or into a single-file loading ramp. There is one
mistake in Fig. 5; the sliding gate at the junction between the single-file race and the crowd pen should
be constructed from bars so that the cattle can see through it. A solid sliding gate makes the race
entrance look like a dead end. Research indicates that solid fences for crowd pens are more efficient.
Cattle moved faster through a crowd pen with solid fences compared to one with a pipe fence or
partially open-board fence (Vowles et a]., 1984b). The inside of Fig. 5 is smooth to prevent bruises. All
structural supports are on the outside.

If a straight crowd pen is used with a funnel leading to the single-file race, one side should be straight
and the other side should be on a 30' angle (Meat and Livestock Commission, no date). If space
permits, a round crowd pen is recommended because it is more efficient, as some types of cattle move
more slowly when they walk straight through the crowd pen into the single-file race (Vowles et al.,
1984b).

Mangates should be installed as indicated on Fig. 4, and they should be 45 cm wide because large
cattle cannot pass through the narrow opening. A hinged solid metal or plywood flap which opens

http://grandin.com/references/design.construction.facilities.handling.cattle.html (9 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

inward toward the cattle makes a good mangate. The flap is held shut with a spring and there is no
latch. If a person is chased by the cattle, he can open the gate quickly because there is no latch.

8. Loading ramps

Fig. 4 has a gate which can be used to direct cattle to either the loading ramp or the single-file race to
the squeeze. In the US, the most efficient loading ramps are single-file, because US trucks have a
narrow 76 cm wide rear door. Therefore, the ramp should be 76 cm wide for adult cows and fattened
cattle. This is narrow enough to prevent adult cattle from turning around. If the ramp is used for calves
only, it should be made narrower. The efficiency of the ramp can be further improved by curving the
single file ramp. The use of a ramp wider than the truck door is not recommended for loading, because
it is inefficient and the cattle will become bruised when they strike the door frame. In countries where
the back gate of the truck opens up to the full width of the truck, a ramp equal to the truck width can be
used. In the US and other countries where trucks with narrow doors are used, a 2.5-3 m-wide ramp is
recommended for unloading only.

Many animals are injured on loading ramps which are too steep. The maximum recommended angle is
20' for permanent ramps and 25' for adjustable ramps (Grandin, 1983b). The crowd pen on a single-file
loading ramp must have a level floor except for a slight drainage slope. Sloping the floor of the crowd
pen 10' will cause livestock to pile up against the crowd gate. On concrete ramps, stair steps are
recommended. The dimensions for the stair steps are a 30-cm tread width and a 10-cm rise. The steps
should be deeply grooved to provide a nonslip surface. On wooden ramps, the cleats should have 20
cm of space in between them (Mayes, 1978). To help prevent falling during unloading, permanently
installed ramps should have a flat-level dock at the top (Stevens and Lyons, 1977). The minimum
width for the level dock is 1.5 m. A self-aligning dock bumper will help prevent injuries caused by
cattle stepping down between the truck and the loading-dock (Rider et al., 1974). Even if the truck
backs up to the dock into a misaligned position, the gap is blocked by the self-aligning bumper. The
bumper can be constructed from two pieces of steel welded together to form an 'L' shape. The 'L'-
shaped piece of metal pivots on a heavy steel pin attached to the front of the dock. One side of the 'L'
overlaps and rests on the dock floor. Loading ramps should also have telescoping side panels to
prevent cattle from jumping out between the truck and the ramp. If a portable ramp is used, it should be
sturdy. Ramps which sway or move when cattle walk on them are likely to cause balking.

9. Working corral for a large ranch

Figs. 6 and 7 are of a large corral system for gathering cattle for transport, sorting, working through the
squeeze chute, weighing and other chores. It can be used by handlers on foot or people mounted on
horses. It is especially suited for ranches where calves or yearlings are removed from the ranch
annually for shipment to feedlots. The layout shown in Fig. 4 forms the left-hand side of the corral.
The only difference is that the inside radius of the wide curved lane is expanded to 10.66 m. Most of
the actual cattle handling and sorting is conducted in the wide curved lane labeled 'sorting reservoir',
the single-file race, round crowd pen and diagonal pens. Cattle are more easily controlled in the 3.5 m-
wide lanes and pens. The large gathering and post-working pens are only used to hold cattle before and
after the actual handling operation. The curved lanes and diagonal pens eliminate square comers and
promote cattle movement. The gates on the diagonal pens are 4.2 m long on a 3.5 m-wide lane because
gates opening on an angle eliminate sharp comers. The round gathering and holding pens have no

http://grandin.com/references/design.construction.facilities.handling.cattle.html (10 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

square comers for cattle to bunch up in. Fig. 6 is easy to set out by placing strings on the ground as
indicated by the dotted lines. To prevent mistakes, the entire corral should be set out and the ground
should be marked with lime before starting construction.

Fig. 6. Corral layout for a large ranch where calves are shipped to a feedlot.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (11 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 7. Corral similar to Fig. 6 constructed from wood planks.

Groups of 20-40 animals are directed from the gathering pen into the curved sorting reservoir lane.
This lane serves two functions. First, it holds cattle which are waiting to go to the loading ramp, or the
squeeze chute, in the same manner which was described in Fig. 4. Secondly, it holds groups of cattle
which are being sorted back into the diagonal pens (Fig. 6). Sorting back into the diagonal pens is
efficient because the animals have a strong tendency to move back in the same direction from which
they came (Grandin, 1980a). Many US ranchers prefer sorting back into the pens from an alley because
it is quick, and it enables them to see the animals more easily than sorting through a single-file race.
Cattle which have been sorted into the diagonal pens can either be released back to pasture or moved
into the curved lane to go to the scale, loading ramp or squeeze chute.

When cows and calves are being separated, the calves are sorted into the diagonal pens. The cows are
allowed to pass through one of the diagonal pens into the large postworking pen. This corral system
can handle 300 cow-and-calf pairs or 400 adult cattle. To expand the systems, additional diagonal pens
can be added. The length of the diagonal pens should not be increased. If they are too long, the cattle
will bunch up. Increasing the size of the gathering pen is not recommended. If it is too big, driving
cattle into the curved lane may be difficult. To increase the gathering area, an additional round
gathering pen should be built at the pasture entrance. The corrals can be reduced for smaller herds by
omitting one or two of the diagonal sorting pens and reducing the size of the gathering and post-

http://grandin.com/references/design.construction.facilities.handling.cattle.html (12 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

working pens. The basic round shape of the pens should be maintained to eliminate comers for cattle to
bunch up in.

Fig. 6 is equipped with a sorting gate in front of the squeeze chute. When cows are pregnancy-tested,
the pregnant cows can be directed to the post-working pen, and the nonpregnant cows can be directed
into one of the diagonal pens. A second sorting gate and alley can be easily added to create a three-way
sort out of the squeeze chute. The sorting gate or gates in front of the squeeze chute can also be used
for high-speed sorting as cattle walk through the squeeze. Any animal which needs veterinary
treatment can be easily caught in the squeeze. An added advantage of sorting through the squeeze
chute is that the cattle will learn to enter it readily. As an added incentive to enter the squeeze, feed can
be made available in the postworking pen. Feeding palatable barley grain to sheep immediately after
handling reduced the time required to drive them through a race (Hutson, 1985b).

This corral can also be used in pasture rotation systems which have centrally located handling facilities
and the pastures are laid out like a wagon wheel (Savory, 1978). The gathering pen and post-working
pen are eliminated and replaced with a 6 m-wide lane which encircles the corral and forms the hub of
the wheel. Pasture fences radiate from the 6 m-wide lane. Switching cattle from pasture to pasture is
easy when they come in for water in the 6 m-wide lane.

Fig. 6 can also be used in feedlots by eliminating the gathering and post-working pens and connecting
the lanes to the alleys in the feedlot. Additional feedlot handling system layouts are available from
Paine et a]. (no date). Paine's publication contains layouts of diagonal pens for shipping, receiving,
weighing and loading cattle in large feedlots, and it also discusses feedlot hospital design.

The corrals in Figs. 6 and 7 are most suitable for use with British, European or British/European
crosses with Brahman. These types of cattle can be readily sorted back into the diagonal pens by
cutting animals out of the reservoir lane one at a time. Purebred Brahmans and Zebu tend to mill and
circle more tightly. Cutting out animals and sorting them back is often more difficult.

Fig. 8 is designed for large properties (ranches) in Australia or South America which handle Brahman
or Zebu cattle fattened on grass. In this type of operation, the steers remain on the ranch for several
years instead of being shipped to a feedlot. More sorting is required due to the greater range of cattle
ages and types. Older steers which have been sorted many times may be harder to sort back in an alley
than inexperienced calves and yearlings, hence the Australians developed the pound yard (Dept. of
Primary Industries, 1969). It enables the person sorting the cattle to look at each animal carefully
before a sorting decision is made. However, it is slower than sorting back in the alley.

Fig. 8 provides the advantages of both high speed sorting in a single-file race and pound yard sorting.
Cattle can be sorted three ways with the two sorting gates in the single-file race. During sorting, all
cattle have to pass through the headgate and squeeze chute.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (13 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 8. Corral layout for a large Australian or South American ranch which has greater sorting
requirements because steers remain on the ranch for fattening on grass. This design can also be
used with electronic sorting and computerized systems, where each individual animal is
evaluated and then sorted into different weight or frame size categories.

They can be sorted five ways out of the 5-m diameter pound yard. Each animal is admitted one at a
time. A person on a platform over the pound yard can easily open and shut the gates with ropes or
levers. A triangular block gate is used to stop incoming cattle and control cattle flow into the pound
yard. It consists of 1.52 in high solid sided triangle with 76cm sides which is hinged at its apex. For
details on building this gate, refer to Juergenson, 1979; Canada Plan Service, 1979. After sorting, the
cattle in the sorting pens can be easily moved through the return lane for vaccinating, branding, truck
loading, etc. If a dip vat is required, an additional directional gate and race can be added to lead to the
dip vat. Fig. 8 is easy to set out and build by using the dotted lines as a guide. Fig. 4 has been
incorporated into this corral. Sorting pens 2 through 6 are in a half circle with a 17.8-m radius. Fig. 8
can be easily modified for electronic sorting of cattle. Producers in the US are now doing more
individual animal evaluation and there will be an increasing need for the type of layout shown in Fig.
8.

10. Squeeze chutes and headgates

http://grandin.com/references/design.construction.facilities.handling.cattle.html (14 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

A good headgate and squeeze chute will improve the care and management of cattle health because
catching and restraining cattle is easy. There are many different types of commercially available
headgates for restraining the animal's head. Headgates can also be built from plans available from
Midwest Plan Service, 1975, Inglis and Williams, 1979 and Vowles, 1980. The four basic types are
scissors stanchion, full opening stanchion, positive control and self catcher (Grandin, 1980b). A
description and the advantages and disadvantages of each type are listed below.

10.1. Scissors stanchion

It consists of two biparting halves that have pivots at the bottom (Fig. 9). After release, the animal
walks out through the headgate. It is available in the curved bar type shown in Fig. 9 or a straight bar.
The curved bar stanchion in Fig. 9 is one of the most popular general-purpose headgates. The curved
bar provides better head control because it prevents the Fig. 9. Squeeze chute with scissors stanchion
headgate with curved neck bars. animal from sliding its head up and down. The animal may choke if it
lays down in the chute. The straight bar provides poor head control because the animal can slide its
head up and down. Choking in a straight bar stanchion is almost impossible because the straight bars
can not press on the throat. A curved bar stanchion is recommended for general cattle handling on
feedlots and ranches. A straight bar stanchion is recommended for gentle dairy cows and for veterinary
clinics where an animal must remain in the headgate for a long period. It is also recommended if the
primary use of the headgate is restraining cows for pregnancy checking or artificial insemination or
when a headgate is used alone without a squeeze chute.

10.2. Full opening stanchion

This consists of two biparting halves which open and close like a pair of sliding doors. It is available in
both straight bar and curved bar models. The advantage of this type of headgate is that large bulls can
walk through it more easily. The disadvantage is that the sliding mechanism is more complicated.

10.3. Self-catching

This headgate can be set like a trap to automatically catch the animal's head when it enters. Forward
movement of the animal will close the gate around its neck. Self-catching gates are recommended for
gentle cattle without horns. To prevent injuries to the cattle and damage to the gate, the cattle should
walk slowly into the headgate. The mechanism is complex and needs constant adjustment. These gates
work best on small ranches or dairies where a single person handles gentle cattle. They are available in
both curved and straight bar stanchions.

10.4. Positive control

This headgate locks very tightly around the animal's neck like a pillory. It provides excellent control of
the head, but it is more likely to choke animals than a curved bar stanchion. It is recommended for wild
cattle with homes because it is easier to catch homed cattle with this type of gate. After the neck is
released, the animal must back up before the gate is swung open to allow it to exit. Another advantage
is that it requires less effort to operate than the other types of head gates.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (15 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Choking in a headgate is usually asphyxiation caused by excessive pressure on the carotid arteries in
the neck (White, 1961) or on the wind-pipe (Fowler, 1978). Due to the pressure on the arteries, animal
can die very rapidly if it starts to lose consciousness in a headgate. The headgate must be released
instantly when the first signs of asphyxiation occur. Choking is most likely to occur when a headgate is
used without a squeeze. A properly adjusted squeeze chute can greatly reduce choking by preventing
the animal from lying down. The best squeeze chutes have two movable side panels which are hinged
at the bottom and pulled together by a lever system at the top. These are superior to chutes with a
single movable side because the animal remains standing in a balanced position. The 'V' shape of the
squeeze sides supports the animal. Proper adjustment of the space between the squeeze sides at the
floor can greatly reduce choking. For 113-180 kg calves, the squeeze sides should be 16 cm apart at the
chute floor, 21 cm for 272-360 kg cattle and 30 cm apart for most cows and fed steers (Grandin,
1980b). For large bulls the spacing may need to be wider.

On commercially available squeeze chutes, the sides have bars which can be dropped down for access
to the sides of the animal (Fig. 9). The solid panel at the bottom can also be opened for access to the
underside of the animal. When a squeeze chute is being purchased, the position of the control levers
should be considered. On some headgates and squeeze chutes, the levers are situated where they may
injure the operator if a latch is accidentally released. Commercially built headgates and squeeze chutes
have two basic types of latches. The first type is a ratchet-latch which locks into a definite notch as the
headgate or squeeze is closed. It has the disadvantage of being noisy, but it is safer because it is less
likely to be released accidentally. The second type is a friction latch which consists of a steel rod which
passes through a hinged metal plate. It has the advantage of being quieter than a ratchet latch, but it is
more likely to come unlatched accidentally. Friction latches must be well maintained to keep them
safe.

A survey conducted in large feedlots by Grandin (1980b) indicated that operator carelessness and
trying to handle cattle too rapidly was the primary cause of choking, escaping and legs caught in
squeeze chutes. The survey results also indicated that Brahman cross cattle were more likely to escape
from a squeeze chute than English/European cross cattle. Allowing cattle to run rapidly into a squeeze
chute and slam against the headgate can cause serious injuries. Examination of beef carcasses revealed
old, healed spinal injuries in the back and neck (Grandin, 1980b). Even animals which appeared to be
normal may have had hidden spinal damage. A skillful squeeze-chute operator can slow cattle down
before they reach the headgate by partially closing the squeeze. Injuries can also be reduced by
handling cattle quietly in the race leading up to the squeeze chute. Excessive use of electric prods
especially on Brahman, Brahman cross and Zebu cattle can increase squeeze-chute injuries because
excited cattle slam into the headgate and make greater attempts to escape.

To prevent shoulder bruises, the headgate should have neck bars constructed from round pipe with a
minimum diameter of 6.2 cm. A 7.6 cm diameter pipe is recommended. The larger pipe diameter is
less likely to bruise the neck. Headgates can be padded with old conveyor belts or split tires. Split
motorcycle tires are the ideal size for headgate stanchions.

Many large feedlots and some ranches use hydraulics instead of muscle power to operate the squeeze
chute. A correctly adjusted hydraulic squeeze chute is usually safer for both people and animals. The
dangerous protruding levers are eliminated, and people are less likely to become tired and make errors
which can cause an accident. Most commercially available hydraulic squeeze chutes in the US have a

http://grandin.com/references/design.construction.facilities.handling.cattle.html (16 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

factory adjusted pressure relief valve which prevents excessive pressure from being applied to the
animal. Cattle can be seriously injured if excessive squeeze pressure is applied. Animals which have
been oversqueezed will sometimes appear to have pneumonia symptoms a few days later. Autopsies of
cattle which have died from oversqueezing indicated that they had internal ruptures (Grandin, 1980b).
When a hydraulic squeeze chute is designed, the force exerted on the animal should be determined.
Measurements with a hydraulic load cell of the force exerted by the squeeze sides indicated that the
recommended force 69 cm from the bottom pivots at a single point is 454-680 kg for cattle weighing
over 272 kg and 270362 kg for cattle weighing less than 272 kg (Grandin, 1983a). These force
readings are not hydraulic system pressure. Oversqueezing is most likely to occur if the pump motor
supplied with the squeeze chute is substituted with a larger motor or if a tractor hydraulic system is
used. If an animal has difficulty breathing while held in a hydraulic squeeze chute, the pressure relief
valve should be loosened.

11. Calf tables

Young calves on many US ranches are restrained for branding, castration and dehorning by roping
them with a lariat. Roping calves properly so excitement is minimized is a highly skilled occupation.
Many ranches now use a calf table to restrain calves. This is a miniature squeeze chute which can be
tilted to the horizontal position. Commercially available calf tables are available with the four different
types of headgates. Some calf tables have no headgate and the calf table is squeezed and tilted with the
same lever. A well designed calf table requires little physical effort to bring it to the horizontal
position. Tables are available which will handle up to 200 kg calves. For tilting adult cattle to the
horizontal position for foot trimming, two basic types of equipment are commercially available: a
tilting table on which the animal is secured by two wide belly straps, or a tilting squeeze chute. The
tilting squeeze chute is safer for both the operator and the animal.

12. Artificial insemination chute

For improved conception rates, cows should be handled gently during artificial insemination. They
should not be allowed to become agitated and overheated (Stott et al., 1975). The chute used for
artificial insemination should not be used for painful procedures such as dehorning, branding or having
her head pulled around and restrained with nose tongs. Nose tongs are very aversive to cattle and they
will attempt to avoid them after having experienced them once. A less aversive form of head restraint
is a rope halter.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (17 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 10. Dark box chute for artificial insemination and pregnancy testing.

Cows can be easily restrained for artificial insemination or pregnancy testing in a dark-box chute
(Parsons and Helphinstine, 1969; Swan, 1975; Canada Plan Service, 1984) Fig. 10. It has no headgate
or squeeze sides and it will hold the wildest cow with minimum excitement. The dark box is 66-71 cm
wide depending on cow size, and consists of completely solid sides, solid front, and a solid top. A
piece of cloth is hung over the cow's rump to make it completely dark. When the cow is inside the box,
she is in a snug dark enclosure. If the cows refuse to enter the dark box, a small window can be cut in
the front gate. Cow entry is usually not a problem if a good single-file race leads up to the dark box.
The dark box works on the same principle as the dark room which is used for handling deer in New
Zealand. Groups of deer brought into the dark room will allow people to touch them and remain clam.
Outside the dark room, the deer would become agitated and attempt to jump high fences. The dark box
and the dark room may reduce physiological arousal levels (Hale et al., 1987; Lay et al., 1992).
Experiments with poultry indicated that blind-folded birds had lower heartrates and respiration rates
during shackling and slaughter (Douglas et al., 1984). Preliminary experiments with cattle are yielding
a similar result (Kinsman, 1986, personal communication). A new novel dark box can cause stress
(Lay et al., 1992). Prior to breeding cattle should be handled in the box so that they can become
familiar with it.

If wild cows are to be handled, an extra-long dark box can be constructed. A tame cow which is not
displaying estrus is placed in front of the cow which will be inseminated. A wild cow will usually

http://grandin.com/references/design.construction.facilities.handling.cattle.html (18 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

stand quietly and place her head on the 'Pacifier' cow's rump. Cattle will often remain calmer when
they are in bodily contact with other cattle (Ewbank, 1968). After insemination the cow is released
through a side gate. The 'pacifier' cow remains in the dark box. If large numbers of cows are going to
be pregnancy checked or inseminated, 26 dark-box chutes can be built side by side in a herringbone
pattern on a 60' angle (McFarlane, 1976). They are built like regular dark-box chutes and the cows exit
through the front of each chute. On some herringbone systems a single, large front gate is used to
release all the cows at once. The outer fences, front gates, and tops are solid. The fences in between the
cows are constructed from bars so the cows can see and feel each other. This will help keep them
calmer.

13. New restraint ideas

There is a need to improve restraint devices for handling cattle, especially for extensively raised
animals that are often wild. When untamed semi-wild cattle are handled in a squeeze chute, 1.6-7.8%
are bruised (Brown et al., 1981; Grandin, 1987b). Most of these bruises are caused by hitting the
headgate too hard. From a behavioral standpoint, existing squeeze chutes are poorly designed. The
open barred sides permit cattle to see the operator who is deep inside the animal's flight zone. This may
cause the animals to become agitated. The installation of solid sides and a solid barrier in front of the
headgate to block the animal's vision will keep a semi wild animal calmer (Grandin, 1993b). The
behavioral principles of restraint are: blocking the animal's vision; slow, steady motion of the
equipment and optimal pressure. The device must apply sufficient pressure to provide the feeling of
being held, but excessive pressure that causes pain and struggling should be avoided. Semi-wild cattle
will remain calmer if restraint in a headgate is accompanied with body restraint. Slow steady motions
of people and equipment are calming and sudden jerky motion excites and agitates cattle.

Design ideas from equipment used in slaughter plants should be adopted for ranch and feedlot use
(Marshall et al., 1963; Grandin, 1992, 1993b). A double rail conveyor restrainer used for beef cattle in
slaughter plants outfitted with a head restraint device would almost eliminate injuries to cattle caused
by lunging against the headgate. The animals straddle a moving conveyor. The system is described by
Giger et al. (1977), Grandin 0987b, 1988, 1991, 1993c).

14. Dipping vats

Pharmaceuticals are reducing the need for dipping cattle to eradicate external parasites. Ivermectin has
replaced dipping on many cattle ranches and feedlots in the US. There is still a need for dip vats in
areas where livestock have to be dipped frequently due to the high cost of ivermectin. Dipping is still
required in some quarantine areas because Ivermectin does not kill all the parasites immediately
(Campbell et al., 1983). The eventual replacement of dip vats with injectable or pour on products is
beneficial because dipping is stressful and the disposal of used dip chemicals may create pollution.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (19 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Fig. 11. Dip vat entrance design which will reduce injuries and chemical splashing. From
Grandin, 1980a.

Injuries, stress and chemicals splashing on people can be reduced by a well designed entrance to the
dip vat (Fig. 11, Grandin, 1980a). Many injuries and drownings occur because too many cattle enter
the dip vat at once or they jump on top of each other. The two anti-bunch gates in Fig. 11 can be
adjusted to allow only one animal to pass through at a time. The pair of gates is located on each side of
the single-file race. The opening between the ends of the two gates is adjusted for animal size. To
prevent wild cattle leaping into the vat, an overhead rack directs the animal head first into the water.
Over 95% of the cattle will fully submerge their heads and will not have to be pushed under with a
stick. The hold-down rack also reduces chemical splashing. To further reduce splashing, an 8 cm-
diameter pipe should be installed on both sides of the vat wall approximately 1 m above the water.
Splashing water will hit the pipe and fall back into the vat.

Each animal enters the vat by walking down a ramp which is deeply grooved to prevent the animal
from slipping. The ramp is on a 20-25' angle. The animal can stand on the ramp without slipping.
When it steps out over the steep drop off, its center of gravity will change and it will fall into the water.
The animal will seldom attempt to back out because it does not start slipping. Many vat builders make
the mistake of building a slide. A slide is a bad design because the cattle sometimes flip over
backwards while going down the slide. More detailed information on vat design and construction can

http://grandin.com/references/design.construction.facilities.handling.cattle.html (20 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

be found in Grandin (1980a,c, 1983a). For specific information on chemical use and disposal contact, it
should be made with the local agricultural officials in each country. Universities and pharmaceutical
companies can also provide information on dip vat management and chemical usage.

15. Bruise and injury prevention

Careful, quiet handling will greatly reduce bruises. Fifty percent of all bruises are caused by rough
handling (Grandin, 1983b). Surfaces which contact cattle should be smooth (Stevens and Lyons, 1977).
Sharp comers should be padded with old conveyor belts or split tires. A smooth, flat surface such as
the inside of a race does not need padding. Bruises are most likely to occur when animals hit an object
with a small diameter such as the edge of a steel bar or a nail sticking out of a fence. An animal
striking the comer of a square 10 cm diameter post is more likely to bruise than an animal striking a
round 10 cm diameter pipe post. Gates should be equipped with tie-backs to hold them back against the
fence. A gate swinging out into an alley can seriously bruise an animal if it becomes jammed between
the end of the gate and the fence. The use of sticks, metal pipes and sharp objects for driving cattle
should be forbidden. Guillotine gates which slide up and down should be counterweighted to prevent
them from injuring an animal's back. The bottom of the guillotine gate should be constructed from a
7.5 cm diameter pipe to prevent bruises. If an air cylinder is used to actuate the gate it should be
connected to the gate with a cable. This will prevent back injuries because gravity will close the
counter balanced gate. Back injuries caused by a powerful cylinder forcing the gate down on an animal
are prevented.

Animals can become crippled and injured if they slip and fall on slippery concrete floors. Cattle
handling facilities should have nonslip floors (Stevens and Lyons, 1977; Grandin, 1983b). In races,
crowd pens, scales and other cattle-handling areas, concrete floors should be deeply grooved. The
grooves should be made in both directions in a 20 cm square or diamond pattern. The grooves should
be 2.5-5 cm deep. In existing facilities, concrete floors can be roughened with a pneumatic hammer or
a grooving machine. These recommendations are for handling facilities where cattle are handled
intermittently such as auctions, feedlots and ranches. The deep grooves described above should not be
used in the animal's living quarters or in milking parlors where dairy cows walk twice a day. The deep
grooves will cause excessive hoof wear in these locations.

16. Washable facilities

In large feedlots, veterinary clinics and dairies, handling facilities should be designed so the squeeze
chute, single-file race and the concrete slab around the squeeze chute can be easily washed. Drains
should be located outside of the areas where cattle will walk. Concrete floors should be sloped
0.630.30 cm every 30 cm towards a drain. Curbs should be installed to contain the wash water and
direct it to a drain. The best type of drains are open concrete ditches. Square concrete ditches should be
constructed slightly wider than the width of a shovel for easy cleaning. One good drain design is to
locate a large drain directly under the squeeze chute and slope the floor towards it from all sides. Cattle
can not see the drain under the squeeze-chute floor.

References

http://grandin.com/references/design.construction.facilities.handling.cattle.html (21 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Blecha, F., Boyles, S.L., Riley, J.G., 1984. Shipping suppresses lymphocyte blastogenic responses in
Angus and Brahman X Angus feeder calves. J. Anim. Sci. 59, 576-583.

Brown, H., Elliston, N.G., McAskill, JW., Tonkins, L.V., 1981. The effect of restraining fat cattle prior
to slaughter on the incidence and severity of injuries resulting in carcass bruises. Proc. West. Sec.
Amer. Soc. Anim. Sci. 32, 363-365.

Campbell, W.C. et al., 1983. Ivermectin: a potent new antiparasitic agent.

Canada Plan Service, 1979. Triangular pivoting gate, Leaflet Plan S-108. In: Beef Cattle Housing and
Equipment, Canada Plan Service, Agric. Eng. Services, Saskatchewan Dept. of Agriculture. Regina,
Saskatchewan.

Canada Plan Service, 1984. Herringbone, A.I. Breeding chute, Plan 1819. Agriculture Canada. Ottowa,
Ontario, Canada.

Dept. of Primary Industries, 1969. Basic plan for beef cattle yards. Advisory Leaflet No. 631, Division
of Animal Industry, Australia.

Douglas, A.G., Darre, M.D., Kinsman, D.M., 1984. Sight restriction as a means of reducing stress
during slaughter. Proc. 30th European Meeting of Meat Research Workers. Briston, England,
September 9-14, 1984, pp. 10- 11.

Ewbank, R., 1968. The behavior of animals in restraint. In: Fox, M.W. (Ed.), Abnormal behavior in
Animals. Saunders, Philadelphia, PA, pp. 159-178.

Fordyce, G., 1987. Weaner training. Queensland Agric. J, 113, 323-324.

Fowler, M.E., 1978. Restraint and handling of wild and domestic animals. Iowa State University Press,
Ames, Iowa.

Giger, W., Prince, R.P., Westervelt, R.G., Kinsman, D.M., 1977. Equipment for low stress animal
slaughter. Trans. Amer. Soc. Agric. Eng. 20, 571-578.

Grandin, T., 1980a. Observations of cattle behavior applied to the design of cattle handling facilities.
Applied Anim. Ethology 6, 19-31.

Grandin, T., 1980b. Good cattle restraining equipment is essential. Vet. Med. and Small Anim.
Clinician 75, 1291-1296.

Grandin, T., 1980c. Safe design and management of cattle dipping vats. Tech. Paper No. 80-5518.
Amer. Soc. Agric. Eng. St. Joseph, Michigan.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (22 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Grandin, T., 1983a. Handling and processing feedlot cattle. In: Thompson, G.B., O'Mary, C.C. (Eds.),
The Feedlot. Lea and Febiger, Philadelphia, pp. 213-235.

Grandin, T., 1983b. Welfare requirements of handling facilities. In: Baxter, S.H., Baxter, M.R.,
McCormack, J.A.C. (Eds.), Farm Animal Housing and Welfare. Martinus Nijhoff, Boston, pp.137-149.

Grandin, T., 1984a. Reduce stress of handling to improve productivity of livestock. Veterinary
Medicine 79, 827-831.

Grandin, T., 1984b. Race system for cattle slaughter plants with a 1.5-cm radius curve. Applied Anim.
behavior Sci. 13, 295299.

Grandin, T., 1987a. Animal handling. Veterinary Clinics of North America: Food Animal Practice 3
(2), 323-338.

Grandin, T., 1987b. Preventing squeeze-chute injuries. Large Animal Veterinarian, September-
October, pp. 14-17.

Grandin, T., 1988. Double rail restrainer conveyor for livestock handling. Journal of Agricultural
Engineering Research 41, 327-338.

Grandin, T., 1991. Double-rail restrainer for handling beef cattle. Paper No. 91-5004. American
Society of Agricultural Engineers. St. Joseph, Missouri, USA.

Grandin, T., 1992. Observations of cattle restraint devices for stunning and slaughtering. Animal
Welfare 1, 85-91.

Grandin, T., 1993a. Behavioral principles of cattle handling under extensive conditions. In: Grandin, T.
(Ed.), Livestock Handling and Transport. CAB International, Wallingford, Oxon, UK, pp. 43-57.

Grandin, T., 1993b. The effect of previous experiences on livestock behavior during handling. Agri-
Practice 14 (4), 15-20.

Grandin, T., 1993c. Handling and welfare in slaughter plants. In: Grandin, T. (Ed.), Livestock
Handling and Transport. CAB International, Wallingford, Oxon, UK, pp. 289-311.

Grandin, T., 1996. Factors which impede animal movement in salter plants. J. Amer. Vet. Med. Soc.
209, 757-759.

Hale, R.H., Friend, T.H., Macauley, A.S., 1987. Effect of method of restraint on heart rate, cortisol and
thyroid hormones. J. Anim. Sci. (Suppl. 1): (Abstract).

Hixon, D.L. et al., 1981. Reproductive hormone secretions and first service conception rate subsequent

http://grandin.com/references/design.construction.facilities.handling.cattle.html (23 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

to ovulation control with Synchromate B. Therio. 16, 219-229. Hutson, G.D., 1982. Flight distance in
Merino sheep. Animal Production 35, 231-235.

Hutson, G.D., 1985a. The influence of barley food rewards on sheep movement through a handling
system. Applied Anim, behavior Sci. 14, 263273.

Hutson, G.D., 1985b. Sheep and cattle handling facilities. In: Moore, B.L., Chenoweth, P.J. (Eds.),
Grazing Animal Welfare. Australian Veterinary Assn., Queensland, pp. 124-136.

Inglis, S., Williams, R., 1979. Cattle yards. Bulletin No. 3/79, Dept. of Agriculture, South Australia.

Juergenson, E.M., 1979. Handbook of Livestock Equipment. Interstate, Danville, Illinois.

Kelley, K.W. et al., 1981. Whole blood leukocytes vs. separated mononuclear cell blastogenesis in
calves, time dependent changes after shipping. Canadian J. Comp. Med. 45, 249-258.

Kilgour, R., 1971. Animal handling in works, pertinent behavior studies. 13th Meat Industry Research
Conference. Hamilton, New Zealand, pp. 9-12.

Kilgour, R., Dalton, C., 1984. Livestock behavior: a Practical Guide. Granada Publishing, Ltd.,
Frogmore, St. Albans, Herts, UK.

Kilgour, R., DeLangen, H., 1970. Stress in sheep resulting from management practices. Proc. New
Zealand Soc. Anim. Production 30, 65-76.

Kilgour, R. et al., 1983. Using operant test results for decisions on cattle welfare. Proc. Conference on
the Human Animal Bond. Minneapolis, MN, June 13-14, 1983.

Kinsman, D.M, 1986. University of Connecticut, Personal communication.

Lay, D.C., Friend, T.H., Grissom, K.K., Hale, R.L., Bowers, C.C., 1992. Novel breeding box has
variable effect on heart rate and cortisol response of cattle. J. Anim. Sci. 35, 1-10.

Lemmon, W.B., Patterson, G.H., 1964. Depth perception in sheep: Effects of interrupting the mother-
neonate bond. Science 145, 835-836.

Livestock Conservation Institute (no date). Only you can stop bruising. 239 Livestock Exchange Bldg.,
South St. Paul, MN.

Marshall, B.L., 1977. Bruising in cattle presented for slaughter. New Zealand Vet. J. 25, 83-86.

Marshall, M., Milbury, E.E., Shultz, E.W., 1963. Apparatus for holding cattle in position for humane
slaughtering. U.S. Patent 3,092,871.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (24 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Mayes, H.F., 1978. Design criteria for livestock loading chutes. Tech. Paper No. 80-4023, Amer. Soc.
Agric. Eng., St. Joseph, mi.

McFarlane, 1., 1976. Rationale in the design of housing and handling facilities. In: Ensminger, M.D.
(Ed.), Beef Cattle Science Handbook. Agriservices Foundation, Clovis, CA 13, pp. 223-227.

Meat and Livestock Commission (no date). Cattle handling. Livestock Buildings Consultancy, Meat
and Livestock Commission, Queensway, Bletchley, Milton Keynes, England. Midwest Plan Service,
1975. Beef Housing and Equipment Handbook, 3rd edn. Iowa State University, Ames, Iowa.

Paine, M., Teter, Guyer, P. (no date). Feedlot layout. Great Plains Beef Cattle Handbook, Bulletin GPE-
5201 Agricultural Extension, Oklahoma State University, Stillwater, OK.

Parsons, R.A., Helphinstine, W.N., 1969. Rambo Al breeding chute for beef cattle. University of
California Agricultural Extension Service, Davis, CA.

Prince, J.H., 1977. The eye and vision. In: Swenson, M.J. (Ed.), Dukes Physiology of Domestic
Animals. Cornell University Press, New York, pp. 696-712.

Rider, A., Butchbaker, A.F., Harp, S., 1974. Beef working, sorting and loading facilities. Technical
Paper No. 74-4523. Amer. Soc. Agric. Eng., St. Joseph, MI.

Savory, A., 1978. Ranch and range management using the short duration grazing method. In:
Ensminger, M.E. (Ed.), Beef Cattle Science Handbook, Vol. 15. Agriservices Foundation, Clovis, CA,
pp. 376-381.

Stermer, R.A., Camp, T.H., Stevens, D.G., 1981. Feeder cattle stress during handling and
transportation. Technical Paper No. 81-6001. Amer. Soc. Agric. Eng., St. Joseph, MI.

Stevens, R.A., Lyons, D.J., 1977. Livestock bruising project: Stockyard and crate design. National
Materials Handling Bureau, Dept. of Productivity, Australia (no city listed).

Stott, G.H. et al., 1975. Embryonic mortality. West. Dairy J., April, pp. 26-27.

Swan, R., 1975. About Al facilities. New Mexico Stockman, February, pp. 2425.

Tulloh, N.M., 1961. behavior of cattle in yards: 11. A study of temperament. Anim. Behav. 9, 25-30.

Vowles, W.J. 1980. A walk-through headbail for farmers to build. Agnote 1327/80. Victoria Dept. of
Agriculture, Australia.

Vowles, W.J., Hollier, T.J., 1982. The influence of cattle yard design on the movement of animals.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (25 of 26) [2007-12-18 13:23:25]

The design and construction of facilities for handling cattle

Proc. Aust. Soc. Anim. Prod. 14, 597.

Vowles, W.J., Eldridge, G.A., Hollier, T.J., 1984a. The behavior and movement of cattle through
single file handling races. Proc. Soc. Anim. Prod. 15, 767.

Vowles, W.J., Eldridge, G.A., Hollier, T.J., 1984b. The behavior and movement of cattle through
forcing yards. Proc. Aust. Soc. Anim. Prod. 15, 766.

White, J.B., 1961. Letter to the Editor. Vet. Rec. 73, 935.

Wythes, J.R., Shorthose, W.R., 1984. Marketing cattle: its effect on liveweight carcasses and meat
quality. Australian Meat Research Committee Review, No. 46, A.M.R.C., Sydney.

Zavy, M.T., Juniewicz, P.E., Phillips, W.A., Von Tungeln, D.L., 1992. Effects of initial restraint,
weaning and transport stress on baseline and ACTHstimulated cortisol responses in beef calves of
different genotypes. Am. J. Vet. Res. 53, 551-557.

Click here to return to the Homepage for more information on animal behavior, welfare, and care.

http://grandin.com/references/design.construction.facilities.handling.cattle.html (26 of 26) [2007-12-18 13:23:25]