R S 4 2 5 R e cl a i m e r / S t a b i l i z e r I S P E C I F I C AT I O N S

Diesel Engine Wheel & Drive Systems

Caterpillar C-13 DIT ATAAC engine meets Tier III A (US Transmission: 2 speed
Environmental Protection Agency Standards) and Stage III
Travel Speed
(European Environmental Standards) for emissions requirements.
Gross horsepower @ 2,100 rpm, 416 hp (310 kW). 0 - 12 mph (0 - 19.31 km/hr) 2-Wheel Drive
Gross horsepower based on SAE J1995 standard conditions 77°F 0 - 5 mph (0 - 8.04 km/hr) All Wheel Drive
(25°C) and 29.31 in (99 kPa) Hg using 35 API gravity fuel and Working Speed
engine equipped with fuel, lube oil, and jacket water pumps. No
derating required up to 3,300 ft (1,005.84 m) altitude. 0 - 254 ft/min (0 - 71.6 m/min) 2-Wheel Drive
Four-cycle diesel engine with 6 cylinders, 5.1 in (130.0 mm) bore, 0 - 190 ft/min (0 - 57.9 m/min) 4-Wheel Drive
6.2 in (157 mm) stroke and 763 in3 (12.5 L) displacement. 0 - 190 ft/min (0 - 57.9 m/min) 4-Wheel Drive | Positive Assist
Air cleaner, dry type, two stages with visual service indicator. Front Axle - Steering drive axle with dual hydraulic cylinders,
24 volt electric starting system 60 amp alternator. nose-mounted transmission, differential carrier and planetary
Rotary Cutter Assembly wheel drives.
Pump - Variable electrical displacement control with load sensing
8 ft (2.44 m) wide x 50 in (1.27 m) diameter mandrel and pressure protection systems.
Positive displacement lube system which provides lubrication of Motor - Fixed displacement, closed loop with high-pressure
the lower drive shaft to seal cutter bearing. limiter.
232 tungsten carbide teeth with 0.75 in (19 mm) shanks. Teeth Rear Axle - Unitized design incorporates two steerable hydraulic
tap in/tap out for easy replacement. 218 replaceable heavy-duty wheel motors which oscillate to provide the third point in machine
steel holders on mandrel with unique dowel location system. suspension.
RS425C Reclaimer/Stabilizer
Cutting Width...................................................96 in (2,438 mm) I SPECIFICATIONS
Tires ....................................................Front - 26.5 x 25 (20PR)
Cutting Depth ............................................up to 16 in (406 mm) ................................................................Rear - 23.1-26 (10PR)
Mechanical Cutter Drive System Operator’s Station
• Direct drive results in maximum breakout force for higher • Selectable left or right operator's console with 90 degree
production rates. rotation for maximum visibility.
• Cutter drive engagement is controlled with on/off switch at the • Machine stability and low vibration reduce operator fatigue.
operator control console.
• Highly-visible systems gauges and controls.
• Engagement and disengagement is through an engine mounted
clutch and transmission which also provide for cutter speed Steering
changes.
Four-wheel steering and four-wheel drive lets operator control
• Two stage engine and cutter drive transmission overload coordinated steering (all wheels), crab steering, and steering of
protection includes a continuously engaged friction-type torque either leading pair of wheels.
limiter between transmission and differential and a load
sensing electrical control which responds to drops in engine Air System
speed with appropriate reductions in travel speed to maintain
maximum power to cutter. Two 11 gal (41,71 L) reservoir, one engine-mounted compressor,
approximately 13 ft3/min (0.62 m3/min, 8.2 bar/120 psi safety
• Three-speed select cutter transmission provides the cutter valve, quick couplers for hook-up on air impact tool.
torque needed in tough applications. Operator can select speed
range for optimum gradation. Brakes
Cutter Speeds – 3 Speed Select Heavy-duty, air-operated shoe brakes are provided on the
• 1st. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 rpm front-wheel drive axle. Brakes meet both service and parking
requirements for rubber tired construction equipment. Designed
• 2nd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 rpm to meet SAE J1152 for rubber tired construction equipment.
• 3rd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 rpm Service – Air and hydrostatic system
Heavy gauge, 163,000 lb (74,091 kg) double capacity steel drive Park – Fail-safe
chain consists of twice the amount of sideplates and hardened pins
and rollers. Heavy gauge steel chain case is partially filled with oil Emergency – Air
for chain lubrication.
Mainframe
Fabricated heavy-duty unitized-type construction. Engine and console
mounted on mainframe.
 RS425 I Reclaimer/Stabilizer
30 ft 1 in
(9.2 m)

10 ft 1 in
3.1 m

13 ft 5.5 in
4.1 m

10 ft 5 in
3.06 m

17 ft 5 in
5.3 m

Lights Weights and Dimensions

Lighting systems include job site floods, rotating beacon, • Weight* ....................................49,000 lb (22,225.62 kg)
instrument, tail and headlights. • Operating weight .....................51,000 lb (23,132.78 kg)
Service Refill Capacities • Wheel Base .......................................17 ft 5 in (5.31 m)
• Turning Radius .........................................21 ft (6.40 m)
Fuel Tank............................................................250 gal (946 L)
• Overall Width .....................................10 ft 1 in (3.07 m)
Hydraulic Oil Tank..............................................50 gal (189.3 L)
• Overall Length ...................................30 ft 1 in (9.17 m)
Cooling System .................................................18 gal (68.14 L)
• Overall Height (standard) ................10 ft 5.5 in (3.19 m)
Optional Equipment
(with ROPS) .................13 ft 3 in (4.04 m)
• Bi-directional operation kit with upcut/downcut capability * Weight without A/B cutting capability
• ROPS Dimensions will vary depending on options.
• Water/emulsion application system 500 gal/min
All dimensions and weights provided with standard width cutter.
Operating and transportation dimensions and weights will vary depending
on selected options.
All electrical specifications used herein refer to U. S. Standards of voltage
and frequency. Any electrical equipment that is factory installed will be
compatible with power availability requirements of any customer's country.