J A PA N E S E

INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association

JIS B 0001 : 2019

(JSA)
Technical drawings for mechanical
engineering

ICS 01.100.20
Reference number : JIS B 0001 : 2019 (E)

PROTECTED BY COPYRIGHT 52 S
B 0001 : 2019

Date of Establishment: 1958-10-07

Date of Revision: 2019-05-20
Date of Public Notice in Official Gazette: 2019-05-20
Investigated by: Japanese Industrial Standards Committee
Standards Board for ISO area

JIS B 0001 : 2019, First English edition published in 2020-08

Translated and published by: Japanese Standards Association

Mita MT Building, 3-13-12, Mita, Minato-ku, Tokyo, 108-0073 JAPAN

In the event of any doubts arising as to the contents,

the original JIS is to be the final authority.

© JSA 2020
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or
utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.

Printed in Japan
AT

PROTECTED BY COPYRIGHT
 B 0001 : 2019

Contents

Page

1 Scope ························································································································ 1
2 Normative references ····························································································· 1
3 Terms and definitions ···························································································· 2
4 General matters ······································································································ 3
5 Size and format of drawings ·················································································· 6
5.1 Size of drawings ······································································································ 6
5.2 Format of drawings ································································································ 7
6 Lines ························································································································· 8
6.1 Thickness of lines ··································································································· 8
6.2 Types and application of lines ··············································································· 9
6.3 Order of priority of coinciding lines ···································································· 15
7 Characters and texts ···························································································· 16
7.1 Types and height of characters ··········································································· 16
7.2 Expression of texts ······························································································· 19
8 Method of projection ····························································································· 19
8.1 General matters ···································································································· 19
8.2 Designation of projection view ············································································ 19
8.3 Third angle projection method ············································································ 20
8.4 First angle projection method ············································································· 21
8.5 Reference arrow layout ························································································ 21
8.6 Other projection methods ····················································································· 23
9 Scale ······················································································································· 23
10 Expression of view ································································································ 24
10.1 Expression of projection view ·············································································· 24
10.2 Sectional view ······································································································· 29
10.3 Omission of views ································································································· 39
10.4 Special representation of view ············································································ 45
11 Dimensioning ········································································································· 52
11.1 General matters ···································································································· 52
11.2 Projection lines ······································································································ 55
11.3 Dimension lines ····································································································· 56
11.4 Dimension figures ································································································· 60
11.5 Arrangement of dimensions ················································································· 64
11.6 Symbols for dimensioning ···················································································· 67
11.7 Expression of hole dimensions ············································································ 78

(i)

PROTECTED BY COPYRIGHT
B 0001 : 2019

11.8 Expression of keyway ··························································································· 82

11.9 Expression of dimensions of steel constructions and the like ························· 87
11.10 Expression of thin wall part ················································································ 90
11.11 Display of range of working and surface treatment ········································· 91
11.12 Dimensions of non-rigid parts ············································································· 91
11.13 Non-proportional dimensions··············································································· 92
11.14 Dimensions of identical shapes ··········································································· 92
12 Expression of dimensions of full view ································································ 94
13 Reference number ································································································· 95
14 Correction and change of drawing ······································································ 96
Bibliography ······················································································································ 97

(ii)

PROTECTED BY COPYRIGHT
 B 0001 : 2019

This Japanese Industrial Standard has been revised by the Minister of Economy, Trade
and Industry through deliberations at the Japanese Industrial Standards Committee as
the result of proposal for revision of Japanese Industrial Standard submitted by
Japanese Standards Association (JSA) with the draft being attached, based on the
provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the
case of revision by the provision of Article 14. Consequently JIS B 0001:2010 is replaced
with this Standard.
This JIS document is protected by the Copyright Law.
Attention is drawn to the possibility that some parts of this Standard may conflict with
patent rights, applications for a patent after opening to the public or utility model rights.
The relevant Minister and the Japanese Industrial Standards Committee are not
responsible for identifying any of such patent rights, applications for a patent after
opening to the public or utility model rights.

(iii)

PROTECTED BY COPYRIGHT
Blank
JAPANESE INDUSTRIAL STANDARD JIS B 0001 : 2019

Technical drawings for mechanical

engineering

1 Scope
This Japanese Industrial Standard specifies the technical drawings for mechanical
engineering, mainly part drawings and assembly drawings based on JIS Z 8310.
The matters not stated in this Standard shall be in accordance with JIS Z 8310 and
other individual Japanese Industrial Standards related to technical drawings.

2 Normative references
The following standards contain provisions which, through reference in this text, con-
stitute provisions of this Standard. The most recent editions of the standards (including
amendments) indicated below shall be applied.
JIS B 0021 Geometrical product specifications (GPS)—Geometrical tolerancing—
Tolerancing of form, orientation, location and run-out
JIS B 0026 Technical drawings—Dimensioning and tolerancing—Non-rigid parts
JIS B 0028 Geometrical product specifications (GPS)—Dimensioning and toler-
ancing—Cones
JIS B 0031 Geometrical Product Specifications (GPS)—Indication of surface texture
in technical product documentation
JIS B 0405 General tolerances—Part 1: Tolerances for linear and angular dimen-
sions without individual tolerance indications
JIS B 0419 General tolerances—Part 2: Geometrical tolerances for features without
individual tolerance indications
JIS B 0420-1 Geometrical product specifications (GPS)—Dimensional tolerancing—
Part 1: Linear sizes
JIS B 0601 Geometrical Product Specifications (GPS)—Surface texture: Profile
method—Terms, definitions and surface texture parameters
JIS B 0672-1 Geometrical Product Specifications (GPS)—Geometrical features—
Part 1: General terms and definitions
JIS B 0681-2 Geometrical product specifications (GPS)—Surface texture: Areal—
Part 2: Terms, definitions and surface texture parameters
JIS Z 3021 Welding and allied processes—Symbolic representation
JIS Z 8114 Technical product documentation—Terms relating to technical drawings
JIS Z 8310 Technical drawings—General code of drafting practices
JIS Z 8311 Technical drawings—Sizes and layout of drawing sheets
JIS Z 8312 Technical drawings—General principles of presentation—Basic conven-
tion for lines

PROTECTED BY COPYRIGHT