Catálogo Pferd Limas Rotativas HP-TC en

Tungsten carbide burrs
for high-performance applications
TRUST BLUE
■ Optimum stock removal rate, high aggressiveness and good guidance

■ Significant time savings and a high economic value in comparison to
conventional burrs
■ PFERD offers tungsten carbide burrs also with high-quality HICOAT coating
TC burrs for high-performance applications
PFERD cuts
CutPage
3 PLUS HC-FEP 7
■ Universal cut medium, cross cut.
■ Machining of steel, cast iron, stainless steel (INOX), nickel-based alloys and
titanium alloys.
■ High stock removal.
ALLROUND13
■ High stock removal rate on key materials such as steel, cast steel, stainless steel (INOX),
non-ferrous metals and cast iron.
■ Similar to the 3 PLUS cut but with a significantly higher stock removal rate.
STEEL23
■ Extremely high stock removal rate on steel and cast steel.
■ Smooth milling.
■ Reduced vibration and less noise.
INOX34
■ Extremely high stock removal rate on all austenitic, rust and acid-resistant steels,
stainless steel (INOX) and soft titanium alloys.
■ Significantly reduced vibration and less noise.
ALU41
■ High stock removal rate on aluminium and aluminium alloys, non-ferrous metals and
plastics.
■ Smooth milling.
NON-FERROUS41
■ High stock removal rate on non-ferrous metals, brass, copper, plastics and
fibre-reinforced plastics.
■ Suitable for universal use.
CAST48
■ Extremely high stock removal rate on cast iron.
■ Smooth milling.
TITANIUM53
■ Outstanding stock removal rate and tool life on hard titanium alloys.
■ Significantly increased aggressiveness, large chips and very good chip removal.
PLAST58
■ Trimming and contour milling of workpieces made from less hard glass and
carbon-fibre-reinforced duroplastics (GRP and CRP with up to 40 % fibre content) and
fibre-reinforced thermoplastics.
■ Minimized delamination and fraying through straight cut.
■ Highly suitable for use on machines and on robots.
2
PFERD cuts
CutPage
FVK58
■ Trimming and contour milling of workpieces made from hard glass and carbon-fibre-
reinforced duroplastics (also GRP and CRP over 40 %).
FVKS58
■ Similar to the FVK cut.
■ Smooth milling.
TOUGH60
■ High stock removal rate on cast iron, steel up to 54 HRC.
■ Extremely resistant to impacts.
■ Also suitable for use with high surface contact angles over 1/3 and under impact loads.
TOUGH-S60
■ High stock removal rate on cast iron, steel up to 54 HRC.
■ Similar to the TOUGH cut, but with smoother milling and shorter chips.
■ Extremely resistant to impacts.
■ Also suitable for use with high surface contact angles over 1/3 and under impact loads.
MICRO66
■ Good stock removal on almost all materials up to 68 HRC.
■ High surface quality.
EDGE73
■ Creates exact edge shapes – with either 30° or 45° chamfering or a defined radius of
3.0 mm.
■ Safe and comfortable to guide.
Tungsten carbide burrs with HICOAT coating

3 PLUS HC-FEP cut 7
ALLROUND cut 13
STEEL cut 23
INOX cut 34
ALU cut 41
■ In general, all PFERD tungsten carbide burrs are also available with HICOAT coatings.
■ Improved anti-adhesion characteristics.
■ Effective chip discharge.
■ Lower thermal loads.
■ Increased tool life.
■ Also suitable for use at higher cutting speeds when compared with uncoated burrs.
3
The fast way to the best tool
Application Material group Application High-performance Page

application
Construction steels, carbon steels, STEEL 23

Steels up to Coarse stock
tool steels, non-alloyed steels, ALLROUND 13
1,200 N/mm² removal
case-hardened steels, cast steel, 3 PLUS HC-FEP 7
(up to 38 HRC)
alloyed steels Fine stock removal MICRO 67
Steel,
cast steel STEEL 23
Hardened, Coarse stock
heat-treated steels Tool steels, tempering steels, ALLROUND 13
removal
over 1,200 N/mm² alloyed steels, cast steel 3 PLUS HC-FEP 7
(over 38 HRC) Fine stock removal MICRO 67
Stainless Coarse stock INOX 34
Rust and acid- Austenitic and removal
steel ALLROUND 13
resistant steels ferritic stainless steels
(INOX) Fine stock removal MICRO 67
Deburring, Coarse stock
chamfering, Aluminium alloys removal ALU 41
milling out for Fine stock removal
the prepara- Soft non-ferrous
tion of build- NON-FERROUS 41
metals Coarse stock
up welding, ALU 41
Brass, copper, zinc removal
machining ALLROUND 13
weld seams, Fine stock removal ALU 41
machining con-
TITANIUM 53
tours, cleaning Non-ferrous
cast material metals ALU 41
Bronze, titanium/titanium alloys, Coarse stock
Hard non-ferrous NON-FERROUS 41
hard aluminium alloys removal
metals INOX 34
(high Si content)
ALLROUND 13
Fine stock removal MICRO 67
Coarse stock
High-temperature- Nickel-based and cobalt-based alloys On request -
removal
resistant materials (engine and turbine construction)
Fine stock removal MICRO 67
Cast iron with flake graphite EN- Coarse stock CAST 48
GJL (GG), with nodular graphite/ removal ALLROUND 13
Grey cast iron,
Cast iron nodular cast iron EN-GJS (GGG), white
white cast iron
annealed cast iron EN-GJMW (GTW), Fine stock removal MICRO 67
black cast iron EN-GJMB (GTS)
Milling out,
Thermoplastics, fibre-reinforced plastics (GRP/CRP) with a
machining PLAST 58
fibre content up to 40 %
contours Plastics,
Coarse stock
Trimming, other FVK/FVKS 58
removal
contour materials Thermoplastics, fibre-reinforced plastics (GRP/CRP) with a ALU 41
milling, cutting fibre content over 40 %
out holes NON-FERROUS 41
4
Recommendations for use and safety notes
Users of different industries rely on high-performance burrs from PFERD when it comes to
applications like milling out, levelling, deburring or working on weld seams. TC burrs for high-
performance applications are characterized by their material- or application-specific design.
This guarantees an optimum stock removal rate, high aggressiveness and good guidance.
TC burrs for high-performance applications impress by significant time savings and high eco-
nomic value in comparison to conventional burrs. PFERD offers high-pferformance burrs also
with high-quality HICOAT coating.
Advantages:
■ Optimum stock removal rate, high aggressiveness and good guidance.
■ High economic value in comparison to conventional burrs.
■ Impact-free work without chatter marks, thanks to the high concentricity. This reduces wear
on the tool and tool drive.
Recommendations for use: Safety notes:

An optimum rotational speed and power output for the tool drive (pneumatic or electric
grinders, flexible shaft drive) are required for cost-effective use of tungsten carbide burrs.
= Wear eye protection!
■ If possible, use the tools on powerful drives with elastically mounted

spindles to avoid vibration.
■ For cost-effective use of burrs with a shank diameter over 6 mm, = Wear hearing protection!
a tool drive output of, 300–500 watts is required when used at a
RPM
higher rotational speed and cutting speed. Wearing protective gloves is
■ Use the highest rotational speed possible within the recommended = recommended. Handle the tool
rotational speed and cutting speed ranges. drive with both hands.
■ For applications with low stock removal (deburring, chamfering,
minor work on surfaces), the rotational speed can be increased by Observe the recommended
up to 100 % (this excludes tungsten carbide burrs with long shanks). = rotational speed, especially when
using burrs with long shanks!
■ Use only rigid clamping systems and drives as impacts on the tools
and tool chatter lead to premature wear.
■ The burr surface in contact with the workpiece must not exceed 1/3
of the total burr surface. Failure to comply with this recommenda-
tion will result in rough milling behaviour and possibly in broken
teeth. If this cannot be avoided, we recommend using the TOUGH
and TOUGH-S cuts.
1/3 of the total surface
■ In general, burrs are used counterrotationally or with a swinging

motion. To achieve fine finishes, pass the tool rapidly over the
workpiece in the direction of rotation.
In direction of rotation
= fine finish
5
Types with long shanks
Tungsten carbide burrs with a long shank are ideal for cost-effectively machining small, Safety notes:
hard-to-reach areas on components. Long-shank versions are available with the 3 PLUS, 5,
STEEL and TOUGH cuts. Not suitable for robotic or stationary
applications. Risk of bending. Use only rigid
Tungsten carbide burrs with a long shank can be shortened if required. clamping systems/drives.
Tungsten carbide burrs with the designation GL 75 mm are made from solid tungsten carbide,
which means they can only be shortened using diamond tools. Observe the prescribed
=
GL = total length (solid tungsten carbide) rotational speed!
SL = shank length (long steel shank)
Safety note – maximum rotational speed [RPM] for burrs with long shanks
When working with long-shank burrs, it is crucial that the burr is in contact with the To determine the recommended rotational
workpiece (or inserted in the bore or slot to be machined) before the drive system is speed range [RPM], please proceed as
turned on. As a rule, the tool must remain in contact with the workpiece for as long follows:
as the machine is running. Failure to observe this procedure may result in shank failure ➊ Select the required burr diameter.
(bending) and hence an increased risk of accidents. If continuous contact between the tool ➋ For the maximum application speed
and the workpiece is not guaranteed, the ➌ maximum idling speeds stated in the table [RPM] with contact with the workpiece,
must not be exceeded. please refer to the right-hand side of the
table.
For safety reasons, the maximum application speeds ➋ with contact with the workpiece re-
quire a reduction in the recommended speed of tungsten carbide burrs with standard shanks.
The reduced speeds are stated in the table below.
Example: ➌ Maximum ➋ Maximum

TC burr, SL 150 mm, idling speed [RPM] application speed [RPM]
STEEL cut, without contact with the workpiece with contact with the workpiece
burr dia. 12 mm. ➊
Coarse stock removal on steels Burr dia. Shank length [mm]
up to 1,200 N/mm². [mm] 75 150 75 150
Maximum application speed with contact 3 10,000 - 31,000 -
with the workpiece: 7,000 RPM
6 6,000 8,000 15,000 15,000
8 - 6,000 - 11,000
10 - 4,000 - 9,000
12 - 3,000 - 7,000
Extensions for drive spindles

In some applications, drive spindle extensions are an economic alternative to customized burrs
with long shanks. Further information can be found here.
6
TC burrs 3 PLUS HC-FEP cut
for coarse stock removal
TC burrs for for coarse stock removal on the key materials used in industrial manufacturing. 3 PLUS cut (MX according to DIN 8033)
They provide a good stock removal rate and are not specific to a particular material. with HICOAT coating HC-FEP for
Advantages: Recommendations for use: iron and steel materials
■ Good stock removal rate through optimum ■ If possible, use the tools on powerful drives
matching of tungsten carbide, geometry, with elastically mounted spindles to avoid
cut and available coating. vibration.
■ Long tool life. ■ For the cost-effective use of burrs, work
■ Reduced wear on the tool drive due to with higher rotational/cutting speeds.
impact-free work without chatter marks, Power recommendation for tool drives:
thanks to the high concentricity. - Shank diameter of 6 mm: from 300 watts ■ Machining of cast iron and steel.
■ High surface quality. ■ Please observe the rotational speed ■ High stock removal.
recommendations. ■ High hardness and wear resistance.
Materials that can be worked: ■ Effective chip removal through improved
Matching tool drives: anti-adhesion characteristics.
■ Steel, cast steel ■ Very high resistance against thermal load.
■ Flexible shaft drive ■ Increased tool life.
Applications: ■ Straight grinder ■ Also suitable for use at higher cutting
■ Robot speeds when compared with uncoated
■ Milling out ■ Machine tools burrs.
■ Levelling
■ Deburring PFERDVALUE:
■ Cutting out holes
■ Surface work PFERDEFFICIENCY recommends burrs with
■ Work on weld seams HICOAT coating for long fatigue-free and
resource-saving work with perfect results in a
very short period of time.
Recommended rotational speed range [RPM]

To determine the recommended cutting To determine the recommended rotational
speed range [m/min], please proceed as speed range [RPM], please proceed as
follows: follows:
➊ Select the material group to be machined. ➎ Select the required burr diameter.
➋ Determine the type of application. ➏ The cutting speed range and the burr
➌ Select the cut. diameter determine the recommended
➍ Establish the cutting speed range. rotational speed range.
➊ Material group ➋ Application ➌ Cut ➍ Cutting speed

Construction steels, carbon steels,
Steels up to
tool steels, non-alloyed steels, Coarse stock
1,200 N/mm² HICOAT HC-FEP 450–750 m/min
case-hardened steels, cast steel, removal
(up to 38 HRC)
Steel, alloyed steels
cast steel Hardened, heat-
treated steels over Tool steels, tempering steels, Coarse stock
HICOAT HC-FEP 250–450 m/min
1,200 N/mm² alloyed steels, cast steel removal
(over 38 HRC)
Example: ➏ Cutting speeds [m/min]

TC burr, ➎
3 PLUS HC-FEP cut, Burr dia. 250 350 450 600 750
burr dia. 12 mm. [mm] Rotational speeds [RPM]
Coarse stock removal on steels 6 13,000 19,000 24,000 32,000 40,000
up to 1,200 N/mm².
Cutting speed: 450–750 m/min 10 8,000 11,000 14,000 19,000 24,000
Rotational speed range: 12 7,000 9,000 12,000 16,000 20,000
12,000–20,000 RPM
7
Cylindrical shape ZYA without end cut d1 d2

Cylindrical burr according to DIN 8032 with cut conforming to DIN 8033.
l2
PFERDVALUE: l1

d1 l2 d2 l1 Cut Description
[mm] [mm] [mm] [mm] 3 PLUS HC-FEP
EAN 4007220
Shank dia. 6 mm
6 16 6 55 835548 1 ZYA 0616/6 Z 3 PLUS HC-FEP
10 20 6 60 222508 1 ZYA 1020/6 Z 3 PLUS HC-FEP
12 25 6 65 835555 1 ZYA 1225/6 Z 3 PLUS HC-FEP
Ball shape KUD d1 d2

Ball-shaped burr according to DIN 8032 with cut conforming to DIN 8033.
l2
PFERDVALUE: l1

EAN 4007220
Shank dia. 6 mm
6 5 6 45 835586 1 KUD 0605/6 Z 3 PLUS HC-FEP
10 9 6 49 835593 1 KUD 1009/6 Z 3 PLUS HC-FEP
12 10 6 51 835609 1 KUD 1210/6 Z 3 PLUS HC-FEP
8
Cylindrical shape with radius end WRC d1 d2

Cylindrical burr with radius end according to DIN 8032 with cut conforming to DIN 8033.
l2
Combination of cylindrical and ball-shaped geometries. l1
PFERDVALUE:

EAN 4007220
Shank dia. 6 mm
6 16 6 55 835562 1 WRC 0616/6 Z 3 PLUS HC-FEP
10 20 6 60 222546 1 WRC 1020/6 Z 3 PLUS HC-FEP
12 25 6 65 835579 1 WRC 1225/6 Z 3 PLUS HC-FEP
Flame shape B d1 d2
Flame-shaped burr according to ISO 7755/8 with cut conforming to DIN 8033. r l2
l1
PFERDVALUE:

d1 l2 d2 l1 r Cut Description
[mm] [mm] [mm] [mm] [mm] 3 PLUS HC-FEP
EAN 4007220
Shank dia. 6 mm
10 25 6 65 1.7 222515 1 B 1025/6 Z 3 PLUS HC-FEP
12 30 6 70 2.1 222522 1 B 1230/6 Z 3 PLUS HC-FEP
9
Pointed tree shape SPG d1 d2

Pointed tree-shaped burr according to DIN 8032 with cut conforming to DIN 8033,
l2
flattened tip. l1
PFERDVALUE:

EAN 4007220
Shank dia. 6 mm
6 18 6 55 835630 1 SPG 0618/6 Z 3 PLUS HC-FEP
10 20 6 60 222591 1 SPG 1020/6 Z 3 PLUS HC-FEP
12 25 6 65 835654 1 SPG 1225/6 Z 3 PLUS HC-FEP
Conical shape with radius end KEL α

d1 d2
Conical burr with radius end according to DIN 8032 with cut conforming to DIN 8033.
r l2
PFERDVALUE: l1

d1 l2 d2 l1 a r Cut Description
EAN 4007220
Shank dia. 6 mm
10 20 6 60 14° 2.9 222607 1 KEL 1020/6 Z 3 PLUS HC-FEP
12 25 6 65 14° 3.3 222614 1 KEL 1225/6 Z 3 PLUS HC-FEP
30 6 70 14° 2.6 222621 1 KEL 1230/6 Z 3 PLUS HC-FEP
10
Conical pointed shape SKM d1 α d2

Conical pointed burr according to DIN 8032 with cut conforming to DIN 8033, flattened tip.
l2
PFERDVALUE: l1

d1 l2 d2 l1 a Cut Description
EAN 4007220
Shank dia. 6 mm
6 18 6 55 18° 222553 1 SKM 0618/6 Z 3 PLUS HC-FEP
10 20 6 60 28° 222560 1 SKM 1020/6 Z 3 PLUS HC-FEP
12 25 6 65 26° 222577 1 SKM 1225/6 Z 3 PLUS HC-FEP
Tree shape with radius end RBF d1 d2

Tree-shaped burr with radius end according to DIN 8032 with cut conforming to DIN 8033.
l2
PFERDVALUE: l1

EAN 4007220
Shank dia. 6 mm
6 18 6 55 1.5 835616 1 RBF 0618/6 Z 3 PLUS HC-FEP
10 20 6 60 2.5 222584 1 RBF 1020/6 Z 3 PLUS HC-FEP
12 25 6 65 2.5 835623 1 RBF 1225/6 Z 3 PLUS HC-FEP
11
Oval shape TRE d1 d2

Oval burr according to DIN 8032 with cut conforming to DIN 8033. r l2
PFERDVALUE: l1

EAN 4007220
Shank dia. 6 mm
6 10 6 50 2.8 222638 1 TRE 0610/6 Z 3 PLUS HC-FEP
10 16 6 56 4.0 222669 1 TRE 1016/6 Z 3 PLUS HC-FEP
12 20 6 60 5.0 222676 1 TRE 1220/6 Z 3 PLUS HC-FEP
12
TC burrs ALLROUND cut
for versatile use
With the innovative ALLROUND cut, PFERD has developed unique burrs for versatile use on
key materials such as steel and cast steel, stainless steel (INOX), non-ferrous metals and cast
iron. The ALLROUND cut offers all the benefits of the tried-and-tested 3 PLUS cut, but its stock
removal rate is up to 30 % higher for steel. It enables comfortable working with reduced
vibration and less noise. They also offer significant time savings and a high economic value.
PFERD also offers tungsten carbide burrs with ALLROUND cut with a high-quality HICOAT
coating.
Advantages: Applications: Safety note:

■ Reduced wear on the tool drive due to ■ Milling out ■ The very high stock removal rate can cause
impact-free work without chatter marks, ■ Levelling discolouration on the shank. This does not
thanks to the high concentricity. ■ Deburring constitute a safety risk.
Materials that can be worked: ■ Surface work PFERDVALUE:
■ Work on weld seams
■ Steel, cast steel PFERDERGONOMICS recommends burrs
■ Stainless steel (INOX) Recommendations for use: with ALLROUND cut as an innovative tool
■ Non-ferrous metals solution for comfortable working with
■ Cast iron ■ If possible, use the tools on powerful drives significantly reduced vibration and less noise.
with elastically mounted spindles to avoid
Performance values for applications on vibration.
steel ■ For the cost-effective use of burrs, work
with higher rotational/cutting speeds.
up to Power recommendation for tool drives: PFERDEFFICIENCY recommends burrs with
30 % from 300 watts. ALLROUND cut for long fatigue-free and
■ Please observe the rotational speed resource-saving work with perfect results in a
Stock removal rate
recommendations. very short period of time.
Matching tool drives:

■ Flexible shaft drive
■ Straight grinder
■ Robot
■ Machine tools
PFERDVIDEO:
■ Conventional burrs with cross cut Learn more about the advantages
■ Tungsten carbide burrs, ALLROUND cut of using tungsten carbide burrs
with ALLROUND cut.
ALLROUND cut ALLROUND cut with

HICOAT coating HC-FEP
Advantages: Advantages:
■ Significantly better stock removal rate than ■ High hardness and wear resistance.
burrs with a conventional cross cut. ■ Effective chip removal through improved
■ Saves money and time through its very anti-adhesion characteristics.
high stock removal rate on key materials. ■ Very high resistance against thermal load.
■ Comfortable working with reduced ■ Increased service life.
vibration and less noise. ■ Also suitable for use at higher cutting
speeds when compared with uncoated
burrs.
13
for versatile use

follows: follows:
➊ Select the material group to be machined. ➍ Select the required burr diameter.
➋ Select the cut. ➎ The cutting speed range and the burr
➌ Establish the cutting speed range. diameter determine the recommended
rotational speed range.
➊ Material group Application ➋ Cut ➌ Cutting speed

Construction steels, carbon steels, ALLROUND 450–750 m/min
Steels
tool steels, non-alloyed steels, case- Coarse stock
up to 1,200 N/mm²
hardened steels, cast steel, alloyed removal
(< 38 HRC) ALLROUND HC-FEP 450–900 m/min
Steel, steels
cast steel Hardened, ALLROUND 250–450 m/min
heat-treated steels Tool steels, tempering steels, Coarse stock
over 1,200 N/mm² alloyed steels, cast steel removal
ALLROUND HC-FEP 250–600 m/min
(> 38 HRC)
Stain-
Rust and Austenitic and Coarse stock
less steel ALLROUND 450–600 m/min
acid-resistant steels ferritic stainless steels removal
(INOX)
Soft non-ferrous Coarse stock ALLROUND 450–750 m/min
Brass, copper, zinc
Non- metals removal ALLROUND HC-FEP 450–900 m/min
ferrous Bronze, titaniumium/titanium alloys, ALLROUND 450–600 m/min
metals Hard non-ferrous Coarse stock
hard aluminium alloys (high Si
metals removal ALLROUND HC-FEP 450–750 m/min
content)
Cast iron with flake graphite EN-GJL
(GG), with nodular graphite/nodular
Grey cast iron, Coarse stock
Cast iron cast iron EN-GJS (GGG), white an- ALLROUND 450–900 m/min
white cast iron removal
nealed cast iron EN-GJMW (GTW),
Example: ➎ Cutting speeds [m/min]

TC burr, ➍
ALLROUND cut, Burr dia. 250 450 600 750 900
Coarse stock removal on steels 3 27,000 48,000 64,000 80,000 95,000
up to 1,200 N/mm².
12,000–20,000 RPM 10 8,000 14,000 19,000 24,000 29,000
12 7,000 12,000 16,000 20,000 24,000
16 5,000 9,000 12,000 15,000 18,000
14
for versatile use
Cylindrical shape ZYAS with end cut d1 d2

Cylindrical burr according to DIN 8032 with circumferential and end cut. l2
l1
Ordering notes:
■ Please complete the description with the
desired cut.
PFERDVALUE:

[mm] [mm] [mm] [mm] ALLROUND
ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 13 3 43 391303 - 1 ZYAS 0313/3 ...
6 13 3 43 391310 - 1 ZYAS 0613/3 ...
Shank dia. 6 mm
6 16 6 55 092866 - 1 ZYAS 0616/6 ...
8 20 6 60 092897 - 1 ZYAS 0820/6 ...
10 20 6 60 092903 221815 1 ZYAS 1020/6 ...
12 25 6 65 092941 221860 1 ZYAS 1225/6 ...
16 25 6 65 092958 - 1 ZYAS 1625/6 ...

Ball-shaped burr according to DIN 8032.
l2
l1
Ordering notes:
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 2 3 33 391327 - 1 KUD 0302/3 ...
4 3 3 34 391341 - 1 KUD 0403/3 ...
6 5 3 35 391358 - 1 KUD 0605/3 ...
Shank dia. 6 mm
6 5 6 45 093009 - 1 KUD 0605/6 ...
8 7 6 47 093030 - 1 KUD 0807/6 ...
10 9 6 49 093108 221877 1 KUD 1009/6 ...
12 10 6 51 093115 221907 1 KUD 1210/6 ...
16 14 6 54 093146 - 1 KUD 1614/6 ...
15
for versatile use

Cylindrical burr with radius end according to DIN 8032. Combination of cylindrical and
l2
ball-shaped geometries. l1
Ordering notes:
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 13 3 43 391365 - 1 WRC 0313/3 ...
6 13 3 43 391372 - 1 WRC 0613/3 ...
Shank dia. 6 mm
6 16 6 55 093153 - 1 WRC 0616/6 ...
8 20 6 60 093184 - 1 WRC 0820/6 ...
10 20 6 60 093191 221938 1 WRC 1020/6 ...
12 25 6 65 093221 221945 1 WRC 1225/6 ...
16 25 6 65 093238 - 1 WRC 1625/6 ...
Flame shape B d1 d2
Flame-shaped burr according to ISO 7755/8. r l2
l1
Ordering notes:
desired cut.
PFERDVALUE:

[mm] [mm] [mm] [mm] [mm] ALLROUND
ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 7 3 37 0.8 391464 - 1 B 0307/3 ...
6 13 3 43 1.0 391501 - 1 B 0613/3 ...
Shank dia. 6 mm
8 20 6 60 1.5 093269 - 1 B 0820/6 ...
10 25 6 65 1.7 093276 221952 1 B 1025/6 ...
12 30 6 70 2.1 093306 221969 1 B 1230/6 ...
16 35 6 75 2.6 093313 - 1 B 1635/6 ...
16
for versatile use

Pointed tree-shaped burr according to DIN 8032, flattened tip.
l2
Ordering notes: l1
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 7 3 37 391716 - 1 SPG 0307/3 ...
13 3 43 391723 - 1 SPG 0313/3 ...
6 13 3 43 391730 - 1 SPG 0613/3 ...
Shank dia. 6 mm
6 18 6 55 093344 - 1 SPG 0618/6 ...
8 20 6 60 093351 - 1 SPG 0820/6 ...
10 20 6 60 093382 221983 1 SPG 1020/6 ...
12 25 6 65 093399 222003 1 SPG 1225/6 ...
16 30 6 70 093436 - 1 SPG 1630/6 ...

d1 d2
Conical burr with radius end according to DIN 8032.
r l2
Ordering notes: l1
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 6 mm
8 20 6 60 16° 1.25 093481 - 1 KEL 0820/6 ...
10 20 6 60 14° 2.9 093498 222010 1 KEL 1020/6 ...
12 25 6 65 14° 3.3 093535 222027 1 KEL 1225/6 ...
16 30 6 70 14° 4.8 093542 - 1 KEL 1630/6 ...
17
for versatile use

Conical pointed burr according to DIN 8032, flattened tip. l2
l1
Ordering notes:
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 7 3 37 21° 391747 - 1 SKM 0307/3 ...
11 3 41 14° 391754 - 1 SKM 0311/3 ...
6 13 3 43 25° 391761 - 1 SKM 0613/3 ...
Shank dia. 6 mm
6 18 6 55 18° 093696 - 1 SKM 0618/6 ...
8 20 6 60 22° 093702 - 1 SKM 0820/6 ...
10 20 6 60 28° 093719 222072 1 SKM 1020/6 ...
12 25 6 65 26° 093726 222089 1 SKM 1225/6 ...

Tree-shaped burr with radius end according to DIN 8032. r l2
l1
Ordering notes:
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 7 3 37 0.75 391785 - 1 RBF 0307/3 ...
13 3 43 0.75 391891 - 1 RBF 0313/3 ...
6 13 3 43 1.5 392010 - 1 RBF 0613/3 ...
Shank dia. 6 mm
6 18 6 55 1.5 093580 - 1 RBF 0618/6 ...
8 20 6 60 1.2 093641 - 1 RBF 0820/6 ...
10 20 6 60 2.5 093658 222041 1 RBF 1020/6 ...
12 25 6 65 2.5 093672 222065 1 RBF 1225/6 ...
16 30 6 70 3.6 093689 - 1 RBF 1630/6 ...
18
for versatile use

Oval burr according to DIN 8032. r l2
l1
Ordering notes:
desired cut.
PFERDVALUE:

ALLROUND HC-FEP
EAN 4007220
Shank dia. 3 mm
3 7 3 37 1.2 392034 - 1 TRE 0307/3 ...
6 10 3 40 2.8 392041 - 1 TRE 0610/3 ...
Shank dia. 6 mm
6 10 6 50 2.8 093733 - 1 TRE 0610/6 ...
8 13 6 53 3.7 093740 - 1 TRE 0813/6 ...
10 16 6 56 4.0 093757 222096 1 TRE 1016/6 ...
12 20 6 60 5.0 093764 222133 1 TRE 1220/6 ...
16 25 6 65 6.5 093771 - 1 TRE 1625/6 ...
Set 1412 ALLROUND

Set 1412 ALLROUND contains five tungsten carbide burrs for versatile use on key materials
such as steel and cast steel, stainless steel (INOX), non-ferrous metals and cast iron in the
most common shapes and dimensions. The sturdy plastic box protects the tools from dirt and
damage.
The burrs are secured at the shanks, facilitating the selection and withdrawal of the tools.
Five further slots are available for other burrs.
Contents: PFERDVALUE:
5 tungsten carbide burrs,
shank dia. of 6 mm,
ALLROUND cut
1 piece each:
■ ZYAS 1225/6 ALLROUND
■ KUD 1210/6 ALLROUND
■ WRC 1225/6 ALLROUND
■ SPG 1225/6 ALLROUND
■ RBF 1225/6 ALLROUND
Cut Description
ALLROUND
EAN 4007220
Shank dia. 6 mm
133576 1 1412 ALLROUND
19
for versatile use
Set 1403 ALLROUND

The 1403 ALLROUND set contains three small tungsten carbide burrs for use on key materi-
als such as steel and cast steel, stainless steel (INOX), non-ferrous metals and cast iron in the
damage.
3 small tungsten carbide burrs,
shank dia. 3 mm,
ALLROUND cut
1 piece each:
Cut Description
ALLROUND
EAN 4007220
Shank dia. 3 mm
420423 1 1403 ALLROUND
Set 1404 ALLROUND

The 1404 ALLROUND set contains three small tungsten carbide burrs for use on key materi-
als such as steel and cast steel, stainless steel (INOX), non-ferrous metals and cast iron in the
damage.
shank dia. 3 mm,
ALLROUND cut
1 piece each:
Cut Description
ALLROUND
EAN 4007220
Shank dia. 3 mm
420430 1 1404 ALLROUND
20
for versatile use
Set 1406 ALLROUND

The 1406 ALLROUND set contains three versatile tungsten carbide burrs for use on key
materials such as steel and cast steel, stainless steel (INOX), non-ferrous metals and cast iron in
the most common shapes and dimensions. The sturdy plastic box protects the tools from dirt
and damage.
shank dia. 6 mm,
ALLROUND cut
1 piece each:
Cut Description
ALLROUND
EAN 4007220
Shank dia. 6 mm
226698 1 1406 ALLROUND
Set 1414 ALLROUND

The 1414 ALLROUND set contains three versatile tungsten carbide burrs for use on key
materials such as steel and cast steel, stainless steel (INOX), non-ferrous metals and cast iron in
the most common shapes and dimensions. The sturdy plastic box protects the tools from dirt
and damage.
shank dia. 6 mm,
ALLROUND cut
1 piece each:
Cut Description
ALLROUND
EAN 4007220
Shank dia. 6 mm
226704 1 1414 ALLROUND
21
for versatile use
Set 1414 ALLROUND HC-FEP

The 1414 ALLROUND HC-FEP set contains three versatile tungsten carbide burrs with high-
quality HICOAT coating for use on key materials such as steel and cast steel, stainless steel
(INOX), non-ferrous metals and cast iron in the most common shapes and dimensions. The
sturdy plastic box protects the tools from dirt and damage.
shank dia. 6 mm,
ALLROUND cut HC-FEP
1 piece each:
■ ZYAS 1225/6 ALLROUND HC-FEP
■ WRC 1225/6 ALLROUND HC-FEP
■ RBF 1225/6 ALLROUND HC-FEP
Cut Description
ALLROUND HC-FEP
EAN 4007220
Shank dia. 6 mm
226711 1 1414 ALLROUND HC-FEP
22
TC burrs STEEL cut
for use on steel and cast steel
With the innovative STEEL cut, PFERD has developed unique burrs for working with steel and
cast steel. They are characterized by significantly increased aggressiveness and good guidance.
Thus they ensure safe and precise work. The extremely high stock removal rate makes burrs
with the STEEL cut impressive, with significant time savings and a high economic value. PFERD
also offers tungsten carbide burrs with STEEL cut with a high-quality HICOAT coating.
Advantages: Materials that can be worked: PFERDVALUE:

■ Reduced wear on the tool drive due to ■ Steel PFERDERGONOMICS recommends burrs
impact-free work without chatter marks, ■ Cast steel with STEEL cut as an innovative tool solution
thanks to the high concentricity. for comfortable working with significantly
Recommendations for use: reduced vibration and less noise.
Applications:
■ If possible, use the tools on powerful drives
■ Milling out with elastically mounted spindles to avoid
■ Levelling vibration.
■ Deburring ■ For the cost-effective use of burrs, work
PFERDEFFICIENCY recommends burrs with
■ Cutting out holes with higher rotational/cutting speeds.
STEEL cut for long fatigue-free and resource-
■ Surface work Power recommendation for tool drives:
saving work with perfect results in a very
■ Work on weld seams from 300 watts.
short period of time.
■ Please observe the rotational speed
Performance values for applications on recommendations.
steel and cast steel
up to
50 % ■ Flexible shaft drive
Stock removal rate
■ Robot
■ Machine tools
Safety note:
■ The very high stock removal rate can cause
discolouration on the shank. This does not
constitute a safety risk.
PFERDVIDEO:
Learn more about the advantages
■ Conventional burrs with cross cut
of using tungsten carbide burrs
■ Tungsten carbide burrs, STEEL cut
with STEEL cut.
STEEL cut STEEL cut with

■ Up to 50 % higher stock removal rate ■ High hardness and wear resistance.
when used on steel and cast steel in ■ Effective chip removal through improved
comparison to conventional cross-cut anti-adhesion characteristics.
burrs. ■ Very high resistance against thermal load.
■ Significantly increased aggressiveness, ■ Increased service life.
large chips and very good chip removal ■ Also suitable for use at higher cutting
through the innovative tooth geometry. speeds when compared with uncoated
■ Workpiece is protected through much burrs.
lower thermal load.
23
TC burrs STEEL cut
Recommended rotational speed range [RPM] Safety note:

To determine the recommended rotational speed range [RPM], please proceed as follows: Please observe the reduced
➊ Select the cut. ➍ The cutting speed range and the burr rotational speeds for burrs with a
➋ Establish the cutting speed range. diameter determine the recommended long shank. They can be found on
➌ Select the required burr diameter. rotational speed range. page 6.
Material group Application ➊ Cut ➊ Cutting speed

Construction steels, carbon
Steels STEEL 450–750 m/min
steels, tool steels, non-alloyed
up to 1,200 N/mm²
steels, case-hardened steels, cast
(< 38 HRC) STEEL HC-FEP 450–900 m/min
Steel, steel, alloyed steels Coarse stock
cast steel Hardened, removal
STEEL 450–750 m/min
heat-treated steels Tool steels, tempering steels,
over 1,200 N/mm² alloyed steels, cast steel
STEEL HC-FEP 450–900 m/min
(> 38 HRC)
Example: ➍ Cutting speeds [m/min]

TC burr, ➌
STEEL cut, Burr dia. 450 750 900
Cutting speed: 450–750 m/min 6 24,000 40,000 48,000
Rotational speed range:
12,000–20,000 RPM 8 18,000 30,000 36,000
10 14,000 24,000 29,000
12 12,000 20,000 24,000
16 9,000 15,000 18,000
24
TC burrs STEEL cut

Cylindrical burr according to DIN 8032. l2
l1
Ordering notes:
desired cut.
PFERDVALUE:

d1 l2 d2 l1 Cut RPM Description

[mm] [mm] [mm] [mm] STEEL
STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 16 6 55 937198 - 24,000–40,000 1 ZYA 0616/6 ...
8 20 6 60 937211 - 18,000–30,000 1 ZYA 0820/6 ...
10 20 6 60 937235 221662 14,000–24,000 1 ZYA 1020/6 ...
12 25 6 65 937242 221655 12,000–20,000 1 ZYA 1225/6 ...
16 25 6 65 002360 - 9,000–15,000 1 ZYA 1625/6 ...

Cylindrical burr according to DIN 8032. Form ZYAS with circumferential and end cut.
l2
SL = shank length (long steel shank) l1
Safety notes:
The rotational speeds for long-
shank burrs relate to applications
where the tool is in contact with the
workpiece. More safety notes can
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.


STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 16 6 55 937259 - 24,000–40,000 1 ZYAS 0616/6 ...
8 20 6 60 937266 - 18,000–30,000 1 ZYAS 0820/6 ...
10 20 6 60 937310 221600 14,000–24,000 1 ZYAS 1020/6 ...
12 25 6 65 937341 221686 12,000–20,000 1 ZYAS 1225/6 ...
16 25 6 65 002889 - 9,000–15,000 1 ZYAS 1625/6 ...
Long shank dia. of 6 mm, SL 150 mm
8 20 6 170 091173 - 11,000 1 ZYAS 0820/6 ... SL 150
10 20 6 170 091289 - 9,000 1 ZYAS 1020/6 ... SL 150
12 25 6 175 091982 - 7,000 1 ZYAS 1225/6 ... SL 150
25
TC burrs STEEL cut

l2
Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.


STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 5 6 45 936832 - 24,000–40,000 1 KUD 0605/6 ...
8 7 6 47 936849 - 18,000–30,000 1 KUD 0807/6 ...
10 9 6 49 936863 221679 14,000–24,000 1 KUD 1009/6 ...
12 10 6 51 936870 221693 12,000–20,000 1 KUD 1210/6 ...
16 14 6 54 003008 - 9,000–15,000 1 KUD 1614/6 ...
10 9 6 159 092002 - 9,000 1 KUD 1009/6 ... SL 150
12 10 6 160 087206 - 7,000 1 KUD 1210/6 ... SL 150
26
TC burrs STEEL cut

Cylindrical burr with radius end according to DIN 8032. Combination of cylindrical and ball-
l2
shaped geometries. l1
Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.


STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 16 6 55 937129 - 24,000–40,000 1 WRC 0616/6 ...
8 20 6 60 937150 - 18,000–30,000 1 WRC 0820/6 ...
10 20 6 60 937174 222713 14,000–24,000 1 WRC 1020/6 ...
12 25 6 65 936696 221570 12,000–20,000 1 WRC 1225/6 ...
16 25 6 65 003022 - 9,000–15,000 1 WRC 1625/6 ...
8 20 6 170 092309 - 11,000 1 WRC 0820/6 ... SL 150
10 20 6 170 092422 - 9,000 1 WRC 1020/6 ... SL 150
12 25 6 175 092439 - 7,000 1 WRC 1225/6 ... SL 150
27
TC burrs STEEL cut
Flame shape B d1 d2
Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.

d1 l2 d2 l1 r Cut RPM Description

[mm] [mm] [mm] [mm] [mm] STEEL
STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
8 20 6 60 1.5 936719 - 18,000–30,000 1 B 0820/6 ...
10 25 6 65 1.7 092590 221617 14,000–24,000 1 B 1025/6 ...
12 30 6 70 2.1 936764 221624 12,000–20,000 1 B 1230/6 ...
16 35 6 75 2.6 003039 - 9,000–15,000 1 B 1635/6 ...
10 25 6 175 1.7 092446 - 9,000 1 B 1025/6 ... SL 150
12 30 6 180 2.1 092453 - 7,000 1 B 1230/6 ... SL 150
28
TC burrs STEEL cut

l2
Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.


STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 18 6 55 936979 - 24,000–40,000 1 SPG 0618/6 ...
8 20 6 60 936993 - 18,000–30,000 1 SPG 0820/6 ...
10 20 6 60 937013 221716 14,000–24,000 1 SPG 1020/6 ...
12 25 6 65 937082 221648 12,000–20,000 1 SPG 1225/6 ...
16 30 6 70 003046 - 9,000–15,000 1 SPG 1630/6 ...
8 20 6 170 092460 - 11,000 1 SPG 0820/6 ... SL 150
10 20 6 170 092477 - 9,000 1 SPG 1020/6 ... SL 150
12 25 6 175 092484 - 7,000 1 SPG 1225/6 ... SL 150
29
TC burrs STEEL cut

d1 d2
SL = shank length (long steel shank) r l2
l1
Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.

d1 l2 d2 l1 a r Cut RPM Description

STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
10 20 6 60 14° 2.9 936771 221587 14,000–24,000 1 KEL 1020/6 ...
12 30 6 70 14° 2.6 936818 222904 12,000–20,000 1 KEL 1230/6 ...
16 30 6 70 14° 4.8 003053 - 9,000–15,000 1 KEL 1630/6 ...
10 20 6 170 14° 2.9 092576 - 9,000 1 KEL 1020/6 ... SL 150
12 30 6 180 14° 2.6 092583 - 7,000 1 KEL 1230/6 ... SL 150
30
TC burrs STEEL cut
Conical pointed shape SKM d1

α
d2
Conical pointed burr according to DIN 8032, flattened tip.
l2
Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.

d1 l2 d2 l1 a Cut RPM Description

STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 18 6 55 18° 092736 - 24,000–40,000 1 SKM 0618/6 ...
8 20 6 60 22° 092774 - 18,000–30,000 1 SKM 0820/6 ...
10 20 6 60 28° 092781 221747 14,000–24,000 1 SKM 1020/6 ...
12 25 6 65 26° 092859 221754 12,000–20,000 1 SKM 1225/6 ...
10 20 6 170 28° 092545 - 9,000 1 SKM 1020/6 ... SL 150
12 25 6 175 26° 092569 - 7,000 1 SKM 1225/6 ... SL 150
31
TC burrs STEEL cut

Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.


STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
6 18 6 55 1.5 936887 - 24,000–40,000 1 RBF 0618/6 ...
8 20 6 60 1.2 936900 - 18,000–30,000 1 RBF 0820/6 ...
10 20 6 60 2.5 936924 221631 14,000–24,000 1 RBF 1020/6 ...
12 25 6 65 2.5 936931 221563 12,000–20,000 1 RBF 1225/6 ...
16 30 6 70 3.6 003060 - 9,000–15,000 1 RBF 1630/6 ...
8 20 6 170 1.2 092491 - 11,000 1 RBF 0820/6 ... SL 150
10 20 6 170 2.5 092507 - 9,000 1 RBF 1020/6 ... SL 150
12 25 6 175 2.5 092514 - 7,000 1 RBF 1225/6 ... SL 150
32
TC burrs STEEL cut

Safety notes:
be found on page 6.
PFERDVALUE:
Ordering notes:
desired cut.


STEEL HC-FEP
EAN 4007220
Shank dia. 6 mm
8 13 6 53 3.7 092637 - 18,000–30,000 1 TRE 0813/6 ...
10 16 6 56 4.0 092644 221808 14,000–24,000 1 TRE 1016/6 ...
12 20 6 60 5.0 092682 221778 12,000–20,000 1 TRE 1220/6 ...
16 25 6 65 6.5 092729 - 9,000–15,000 1 TRE 1625/6 ...
10 16 6 160 4.0 092521 - 9,000 1 TRE 1016/6 ... SL 150
12 20 6 170 5.0 092538 - 7,000 1 TRE 1220/6 ... SL 150
Set 1812 STEEL

Set 1812 STEEL contains five tungsten carbide burrs for use on steel and cast steel in the
damage.
shank dia. 6 mm,
STEEL cut
1 piece each:
■ ZYA 1225/6 STEEL
■ KUD 1210/6 STEEL
■ WRC 1225/6 STEEL
■ SPG 1225/6 STEEL
■ RBF 1225/6 STEEL
Cut Description
STEEL
EAN 4007220
Shank dia. 6 mm
004357 1 1812 STEEL
33
TC burrs INOX cut
for use on stainless steel (INOX)
With the INOX cut, PFERD has developed innovative burrs for work on stainless steel (INOX).
The INOX cut is characterized by an extremely high stock removal rate on all austenitic as
well as rust- and acid-resistant steels. It creates significantly less vibration than a comparable
cross cut. PFERD also offers tungsten carbide burrs with INOX cut with a high-quality HICOAT
coating.
Advantages: Applications: Safety note:

■ Reduced wear on the tool drive due to ■ Milling out ■ The very high stock removal rate can cause
impact-free work without chatter marks, ■ Levelling discolouration on the shank. This does not
thanks to the high concentricity. ■ Deburring constitute a safety risk.
Materials that can be worked: ■ Surface work PFERDVALUE:
■ Stainless steel (INOX) PFERDERGONOMICS recommends burrs
■ Soft titanium alloys Recommendations for use: with INOX cut as an innovative tool solution
(tensile strength < 500 N/mm²) for comfortable working with significantly
■ If possible, use the tools on powerful drives reduced vibration and less noise.
vibration.
Performance values for applications ■ For the cost-effective use of burrs, work
on stainless steel (INOX) with higher rotational/cutting speeds.
Power recommendation for tool drives: PFERDEFFICIENCY recommends burrs with
up to - Shank diameter of 3 mm: 75 to INOX cut for long fatigue-free and resource-
300 watts saving work with perfect results in a very
100 %
- Shank diameter of 6 mm: from 300 watts short period of time.
Stock removal rate

recommendations.
The RPMs shown in the product tables on
the product pages are for work on stainless
steel (INOX) only.

PFERDVIDEO:
■ Conventional burrs with cross cut ■ Straight grinder Learn more about the advantages
■ Tungsten carbide burrs, INOX cut ■ Robot of using tungsten carbide burrs
■ Machine tools with INOX cut.
INOX cut INOX cut with

■ Outstanding stock removal rate and tool ■ High hardness and wear resistance.
life due to the innovative tooth geometry. ■ Effective chip removal through improved
■ Achieves high surface qualities through anti-adhesion characteristics.
optimum chip formation. ■ Very high resistance against thermal load.
■ Prevents heat discolouration in the ■ Increased service life.
material due to the reduced heat ■ Also suitable for use at higher cutting
generation. speeds when compared with uncoated
burrs.
34
TC burrs INOX cut
Recommended rotational speed range [RPM] PFERD tools for use on stainless steel
More PFERD tools and
information on working
To determine the recommended rotational speed range [RPM], please proceed as follows: with stainless steel (INOX)
➊ Select the material group to be machined. ➎ The cutting speed range and the burr can be found in our PRAXIS
➋ Select the cut. diameter determine the recommended brochure "PFERD tools for use
➌ Establish the cutting speed range. rotational speed range. on stainless steel (INOX)" at
➍ Select the required burr diameter. www.pferd.com.
TRUST BLUE

Stainless Austenitic and Coarse stock INOX 450–600 m/min
Rust and acid-resistant steels
steel (INOX) ferritic stainless steels removal INOX HC-FEP 450–750 m/min
Non-ferrous Coarse stock INOX 250–450 m/min
Non-ferrous metals Titanium/titanium alloys
metals removal INOX HC-FEP 250–600 m/min

TC burr, ➍
INOX cut, Burr dia. 250 450 600 750
Coarse stock removal on stainless steel 3 27,000 48,000 64,000 80,000
(INOX).
Cutting speed: 450–600 m/min 4 20,000 36,000 48,000 72,000
Rotational speed range: 5 16,000 29,000 40,000 48,000
12,000–16,000 RPM 6 13,000 24,000 32,000 40,000
8 10,000 18,000 24,000 30,000
10 8,000 14,000 19,000 24,000
12 7,000 12,000 16,000 20,000
35
TC burrs INOX cut

l1
Ordering notes:
desired cut.
PFERDVALUE:


[mm] [mm] [mm] [mm] INOX
INOX HC-FEP
EAN 4007220
Shank dia. 3 mm
3 13 3 43 930380 - 27,000–64,000 1 ZYA 0313/3 ...
6 13 3 43 930403 - 13,000–32,000 1 ZYA 0613/3 ...
Shank dia. 6 mm
6 16 6 55 900499 - 13,000–32,000 1 ZYA 0616/6 ...
8 20 6 60 952245 - 10,000–24,000 1 ZYA 0820/6 ...
10 20 6 60 952252 222270 8,000–19,000 1 ZYA 1020/6 ...
12 25 6 65 900505 222256 7,000–16,000 1 ZYA 1225/6 ...

Cylindrical burr according to DIN 8032 with circumferential and end cut.
l2
Ordering notes: l1
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 3 mm
3 13 3 43 034453 - 27,000–64,000 1 ZYAS 0313/3 ...
6 13 3 43 034460 - 13,000–32,000 1 ZYAS 0613/3 ...
Shank dia. 6 mm
6 16 6 55 034477 - 27,000–64,000 1 ZYAS 0616/6 ...
12 25 6 65 034484 222249 7,000–16,000 1 ZYAS 1225/6 ...
36
TC burrs INOX cut

l2
Ordering notes: l1
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 3 mm
3 2 3 33 930434 - 27,000–64,000 1 KUD 0302/3 ...
4 3 3 34 034439 - 20,000–48,000 1 KUD 0403/3 ...
5 4 3 35 034446 - 16,000–40,000 1 KUD 0504/3 ...
6 5 3 35 930441 - 13,000–32,000 1 KUD 0605/3 ...
Shank dia. 6 mm
6 5 6 45 900536 - 13,000–32,000 1 KUD 0605/6 ...
8 7 6 47 952269 - 10,000–24,000 1 KUD 0807/6 ...
10 9 6 49 952276 222348 8,000–19,000 1 KUD 1009/6 ...
12 10 6 51 900543 222362 7,000–16,000 1 KUD 1210/6 ...

l2
Ordering notes:
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 3 mm
3 13 3 43 930410 - 27,000–64,000 1 WRC 0313/3 ...
6 13 3 43 930427 - 13,000–32,000 1 WRC 0613/3 ...
Shank dia. 6 mm
6 16 6 55 900512 - 13,000–32,000 1 WRC 0616/6 ...
8 20 6 60 952283 - 10,000–24,000 1 WRC 0820/6 ...
10 20 6 60 952290 222317 8,000–19,000 1 WRC 1020/6 ...
12 25 6 65 900529 222331 7,000–16,000 1 WRC 1225/6 ...
37
TC burrs INOX cut
Flame shape B d1 d2
l1
Ordering notes:
desired cut.
PFERDVALUE:


[mm] [mm] [mm] [mm] [mm] INOX
INOX HC-FEP
EAN 4007220
Shank dia. 6 mm
8 20 6 60 1.5 952306 - 10,000–24,000 1 B 0820/6 ...
10 25 6 65 1.7 952313 222287 8,000–19,000 1 B 1025/6 ...
12 30 6 70 2.1 930502 222294 7,000–16,000 1 B 1230/6 ...

Pointed tree-shaped burr according to DIN 8032, flattened tip. l2
l1
Ordering notes:
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 3 mm
3 7 3 37 034491 - 27,000–64,000 1 SPG 0307/3 ...
13 3 43 034507 - 27,000–64,000 1 SPG 0313/3 ...
6 13 3 43 034514 - 13,000–32,000 1 SPG 0613/3 ...
Shank dia. 6 mm
6 18 6 55 936948 - 13,000–32,000 1 SPG 0618/6 ...
8 20 6 60 952320 - 10,000–24,000 1 SPG 0820/6 ...
10 20 6 60 952337 222409 8,000–19,000 1 SPG 1020/6 ...
12 25 6 65 936894 222430 7,000–16,000 1 SPG 1225/6 ...
38
TC burrs INOX cut

Ordering notes: l1
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 3 mm
3 13 3 43 0.75 930472 - 27,000–64,000 1 RBF 0313/3 ...
6 13 3 43 1.5 930489 - 13,000–32,000 1 RBF 0613/3 ...
Shank dia. 6 mm
6 18 6 55 1.5 900550 - 13,000–32,000 1 RBF 0618/6 ...
8 20 6 60 1.2 952344 - 10,000–24,000 1 RBF 0820/6 ...
10 20 6 60 2.5 952351 222386 8,000–19,000 1 RBF 1020/6 ...
12 25 6 65 2.5 900567 222393 7,000–16,000 1 RBF 1225/6 ...

Ordering notes: l1
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 6 mm
8 13 6 53 3.7 952368 - 10,000–24,000 1 TRE 0813/6 ...
10 16 6 56 4.0 952375 222478 8,000–19,000 1 TRE 1016/6 ...
12 20 6 60 5.0 930519 222492 7,000–16,000 1 TRE 1220/6 ...
39
TC burrs INOX cut

d1 d2
r l2
Ordering notes: l1
desired cut.
PFERDVALUE:


INOX HC-FEP
EAN 4007220
Shank dia. 6 mm
8 20 6 60 16° 1.25 952382 - 10,000–24,000 1 KEL 0820/6 ...
10 20 6 60 14° 2.9 952399 222454 8,000–19,000 1 KEL 1020/6 ...
12 30 6 70 14° 2.6 930496 222461 7,000–16,000 1 KEL 1230/6 ...
Set 1912 INOX

Set 1912 INOX contains five tungsten carbide burrs for processing stainless steel (INOX) in the
damage.
Shank dia. 6 mm, INOX cut
1 piece each:
■ ZYA 1225/6 INOX
■ KUD 1210/6 INOX
■ WRC 1225/6 INOX
■ RBF 1225/6 INOX
■ SPG 1225/6 INOX
Cut Description
INOX
EAN 4007220
Shank dia. 6 mm
068816 1 1912 INOX
40
TC burrs ALU and NON-FERROUS cuts
for use on aluminium/non-ferrous metals
When it comes to machining aluminium and non-ferrous metals, PFERD offers two high-
412 ALU grinding oil
performance cuts and a HICOAT coating which have been designed specifically for demanding
machining tasks on long-chipping and lubricating materials. Grinding oil can be used as an
alternative to the HICOAT coating
Advantages: Recommendations for use: HC-NFE. Grinding oil 412 ALU
in a 400 ml aerosol is particularly
■ Reduced wear on the tool drive due to ■ If possible, use the tools on powerful drives well suited: EAN 4007220791332.
impact-free work without chatter marks, with elastically mounted spindles to avoid Detailed information on grinding
thanks to the high concentricity. vibration. oil 412 ALU can be found in
■ For the cost-effective use of burrs, work our Tool Manual 23, catalogue
Applications: with higher rotational/cutting speeds. section 4.
Power recommendation for tool drives:
■ Milling out - Shank diameter of 3 mm: 75 to
■ Levelling 300 watts
■ Deburring - Shank diameter of 6 mm: from 500 watts
■ Cutting out holes ■ Please observe the rotational speed
■ Surface work recommendations.

■ Robot
■ Machine tools
ALU cut ALU cut with Materials that can be worked:

HICOAT coating HC-NFE ■ Aluminium
■ Bronze
■ Copper
■ Brass
■ Titanium
■ Titanium alloys
■ Zinc
■ Fibre-reinforced plastics (GRP/CRP)
PFERD has further developed the ALU cut The use of burrs with the PFERD HICOAT ■ Thermoplastics
especially for stock removal on aluminium. coating HC-NFE prevents chips adhering
This cut is characterized by its high stock during work on soft aluminium alloys. This PFERDVALUE:
removal rate. increases the tool life and improves the
surface quality of the workpiece. PFERDEFFICIENCY recommends burrs with
HICOAT coating for long fatigue-free and
Advantages: Advantages: resource-saving work with perfect results in a
very short period of time.
■ Extremely high stock removal rate. ■ Mainly used for long-chipping and
■ Large chips. lubricating non-ferrous metals.
■ Reduced material adhesion. ■ Highest stock removal rate.
■ Long tool life and smooth running. ■ Effective chip removal through improved
■ Can be used with cutting speeds of up to anti-adhesion characteristics.
1,100 m/min. ■ Lower thermal loads. PFERDVIDEO:
■ Longer service life. Learn more about the advantages
with ALU cut.
NON-FERROUS cut
PFERD has developed the NON-FERROUS cut Materials that can be worked:
for universal use on non-ferrous metals and
fibre-reinforced plastics. This cut is character- ■ Bronze
ized by its high stock removal rate. ■ Copper
■ Brass
Advantages: ■ Zinc
■ Fibre-reinforced plastics (GRP/CRP)
■ Very good stock removal rate when used ■ Thermoplastics
on non-ferrous metals such as brass and
copper, plastics and fibre-reinforced
plastics.
41
TC burrs ALU and NON-FERROUS cut

follows: follows:
➊ Select the material group to be machined. ➎ Select the required burr diameter.
➋ Determine the type of application. ➏ The cutting speed range and the burr
➌ Select the cut. diameter determine the recommended
➍ Establish the cutting speed range. rotational speed range.
➊ Material group ➋ Application ➌ Cut ➍ Cutting speed

ALU 600–1,100 m/min
Coarse stock removal
ALU HC-NFE 600–1,300 m/min
Aluminium alloys
ALU 900–1,100 m/min
Fine stock removal
Soft non-ferrous ALU 600–1,100 m/min
metals
Coarse stock removal ALU HC-NFE 600–1,300 m/min
Brass, copper, zinc NON-FERROUS 450–600 m/min
ALU 900–1,100 m/min
Fine stock removal
Non-ferrous metals
ALU 600–1,100 m/min
Coarse stock removal
Hard aluminium alloys ALU HC-NFE 600–1,300 m/min
(high Si content) ALU 900–1,100 m/min
Fine stock removal
Hard non-ferrous ALU 600–900 m/min
metals
Coarse stock removal ALU HC-NFE 600–1,100 m/min
Bronze NON-FERROUS 600–900 m/min
ALU 600–1,100 m/min
Fine stock removal
NON-FERROUS
600–1,100 m/min
Coarse stock removal ALU
Plastics, Thermoplastics, fibre-reinforced plastics
other materials (GRP/CRP) ALU HC-NFE 600–1,300 m/min
ALU 600–1,100 m/min
Fine stock removal
Example: ➏ Cutting speeds [m/min]

TC burr, ➎
ALU cut, Burr dia. 450 600 900 1,100 1,300
Coarse stock removal on hard non-ferrous 3 48,000 64,000 95,000 117,000 138,000
metals, e.g. bronze.
16,000–24,000 RPM 10 14,000 19,000 29,000 35,000 42,000
12 12,000 16,000 24,000 30,000 35,000
16 9,000 12,000 18,000 22,000 26,000
42

l1
[mm] [mm] [mm] [mm] NON-FERROUS
EAN 4007220
Shank dia. 6 mm
6 16 6 55 221044 1 ZYA 0616/6 NON-FERROUS
12 25 6 65 533314 1 ZYA 1225/6 NON-FERROUS
Shank dia. 8 mm
12 25 8 65 221051 1 ZYA 1225/8 NON-FERROUS

l2
Ordering notes: l1
desired cut.
PFERDVALUE:
HICOAT coating:

[mm] [mm] [mm] [mm] ALU ALU HC-NFE
EAN 4007220
Shank dia. 3 mm
3 13 3 43 803653 - 1 ZYAS 0313/3 ...
6 13 3 43 803660 - 1 ZYAS 0613/3 ...
Shank dia. 6 mm
6 16 6 55 246986 - 1 ZYAS 0616/6 ...
8 20 6 60 952955 - 1 ZYAS 0820/6 ...
10 20 6 60 533321 - 1 ZYAS 1020/6 ...
12 25 6 65 533345 804117 1 ZYAS 1225/6 ...
16 25 6 65 803974 - 1 ZYAS 1625/6 ...
Shank dia. 8 mm
12 25 8 65 246979 - 1 ZYAS 1225/8 ...
43

Ball-shaped burr according to DIN 8032. l2
l1
Ordering notes:
desired cut.
PFERDVALUE:
HICOAT coating:

[mm] [mm] [mm] [mm] ALU ALU HC-NFE NON-FERROUS
EAN 4007220
Shank dia. 3 mm
3 2 3 33 803714 - - 1 KUD 0302/3 ...
6 5 3 35 803721 - - 1 KUD 0605/3 ...
Shank dia. 6 mm
6 5 6 45 869123 - - 1 KUD 0605/6 ...
8 7 6 47 869130 - 221082 1 KUD 0807/6 ...
10 9 6 49 952962 - - 1 KUD 1009/6 ...
12 10 6 51 533147 804155 533154 1 KUD 1210/6 ...
16 14 6 54 803998 - - 1 KUD 1614/6 ...

l2
Ordering notes:
desired cut.
PFERDVALUE:
HICOAT coating:

[mm] [mm] [mm] [mm] ALU ALU HC-NFE NON-FERROUS
EAN 4007220
Shank dia. 3 mm
3 13 3 43 803691 - - 1 WRC 0313/3 ...
6 13 3 43 803707 - - 1 WRC 0613/3 ...
Shank dia. 6 mm
6 16 6 55 247006 - 221068 1 WRC 0616/6 ...
8 20 6 60 952979 - - 1 WRC 0820/6 ...
10 20 6 60 952986 - - 1 WRC 1020/6 ...
12 25 6 65 533260 804131 533284 1 WRC 1225/6 ...
16 25 6 65 803981 - - 1 WRC 1625/6 ...
Shank dia. 8 mm
12 25 8 65 247013 - - 1 WRC 1225/8 ...
44

l1
Ordering notes:
desired cut.
PFERDVALUE:
HICOAT coating:

[mm] [mm] [mm] [mm] ALU ALU HC-NFE
EAN 4007220
Shank dia. 3 mm
3 7 3 37 003350 - 1 SPG 0307/3 ...
13 3 43 003435 - 1 SPG 0313/3 ...
6 13 3 43 003442 - 1 SPG 0613/3 ...
Shank dia. 6 mm
6 18 6 55 003503 - 1 SPG 0618/6 ...
8 20 6 60 003534 - 1 SPG 0820/6 ...
10 20 6 60 003558 - 1 SPG 1020/6 ...
12 25 6 65 003596 222706 1 SPG 1225/6 ...

d1 d2
r l2
Ordering notes: l1
desired cut.
PFERDVALUE:
HICOAT coating:

[mm] [mm] [mm] [mm] [mm] ALU ALU HC-NFE NON-FERROUS
EAN 4007220
Shank dia. 6 mm
8 20 6 60 16° 1.25 953013 - - 1 KEL 0820/6 ...
10 20 6 60 14° 2.9 953020 - 221105 1 KEL 1020/6 ...
12 30 6 70 14° 2.6 533109 533093 533116 1 KEL 1230/6 ...
16 30 6 70 14° 4.8 804018 - - 1 KEL 1630/6 ...
Shank dia. 8 mm
12 30 8 70 14° 2.6 247037 - - 1 KEL 1230/8 ...
16 30 8 70 14° 4.8 - - 221129 1 KEL 1630/8 ...
45

Ordering notes: l1
desired cut.
PFERDVALUE:
HICOAT coating:

[mm] [mm] [mm] [mm] [mm] ALU ALU HC-NFE
EAN 4007220
Shank dia. 3 mm
3 13 3 43 0.75 803677 - 1 RBF 0313/3 ...
6 13 3 43 1.5 803684 - 1 RBF 0613/3 ...
Shank dia. 6 mm
6 18 6 55 1.5 328071 - 1 RBF 0618/6 ...
8 20 6 60 1.2 952993 - 1 RBF 0820/6 ...
10 20 6 60 2.5 953006 - 1 RBF 1020/6 ...
12 25 6 65 2.5 533208 533192 1 RBF 1225/6 ...
16 30 6 70 3.6 804001 - 1 RBF 1630/6 ...
Shank dia. 8 mm
12 25 8 65 2.5 247020 - 1 RBF 1225/8 ...
46
Set 1603 ALU

Set 1603 ALU contains ten small tungsten carbide burrs for processing aluminium in the
damage.
Contents:
shank diameter of 3 mm, ALU cut
1 piece each:
■ ZYAS 0313/3 ALU ■ WRC 0613/3 ALU
■ ZYAS 0613/3 ALU ■ RBF 0313/3 ALU
■ KUD 0302/3 ALU ■ RBF 0613/3 ALU
■ KUD 0605/3 ALU ■ SPG 0313/3 ALU
■ WRC 0313/3 ALU ■ SPG 0613/3 ALU
Cut Description
ALU
EAN 4007220
Shank dia. 3 mm
004401 1 1603 ALU
Set 1612 ALU

Set 1612 ALU contains five tungsten carbide burrs for processing aluminium in the most
common shapes and dimensions. The sturdy plastic box protects the tools from dirt and
damage.
Contents:
shank diameter of 6 mm, ALU cut
1 piece each:
■ ZYAS 1225/6 ALU ■ RBF 1225/6 ALU
■ KUD 1210/6 ALU ■ KEL 1230/6 ALU
■ WRC 1225/6 ALU
Cut Description
ALU
EAN 4007220
Shank dia. 6 mm
068823 1 1612 ALU
47
TC burrs CAST cut
for use on cast iron
With the CAST cut, PFERD has developed innovative burrs especially for work on cast iron.
They are characterized by an extremely high stock removal rate on cast iron and impress
through smooth milling with significantly reduced vibration and less noise.
Advantages: Applications:
■ Up to 100 % higher stock removal rate ■ Milling out
when used on cast iron due to the innova- ■ Levelling PFERDVALUE:
tive tooth geometry, when compared with ■ Deburring
conventional cross-cut burrs. ■ Cutting out holes PFERDERGONOMICS recommends burrs
■ Significantly increased aggressiveness, ■ Surface work with CAST cut as an innovative tool solution
large chips and very good chip removal. ■ Work on weld seams for comfortable working with significantly
■ Comfortable working with reduced vibra- reduced vibration and less noise.
tion and less noise. Recommendations for use:
■ Reduced wear on the tool drive due to
impact-free work without chatter marks, ■ If possible, use the tools on powerful drives
thanks to the high concentricity. with elastically mounted spindles to avoid
vibration. PFERDEFFICIENCY recommends burrs with
Materials that can be worked: ■ For the cost-effective use of burrs, work CAST cut for long fatigue-free and resource-
with higher rotational/cutting speeds. saving work with perfect results in a very
■ Grey cast iron Power recommendation for tool drives: short period of time.
■ Nodular cast iron from 300 watts.
■ Annealed cast iron ■ Please observe the rotational speed
recommendations.
Performance values for
applications on cast iron Matching tool drives:
up to ■ Flexible shaft drive
100 %
■ Robot
Stock removal rate
■ Machine tools
Safety notes:
■ The very high stock removal rate can cause
discolouration on the shank. This does not
constitute a safety risk.
PFERDVIDEO:
■ Conventional burrs with cross cut
■ Tungsten carbide burrs, Cut CAST
with CAST cut.

To determine the recommended rotational speed range [RPM], please proceed as follows:
➊ Refer to the table for the cutting speed. ➌ The cutting speed range and the burr
➋ Select the required burr diameter. diameter determine the recommended
Material group Application Cut ➊ Cutting speed

Cast iron with flake graphite EN-GJL (GG),
with nodular graphite/nodular cast iron
Grey cast iron, Coarse stock
Cast iron EN-GJS (GGG), white annealed cast iron CAST 450–750 m/min
white cast iron removal
EN-GJMW (GTW), black cast iron EN-GJMB
(GTS)
Example: ➌ Cutting speeds [m/min]

TC burr,
Cut CAST, ➋ 450 750
burr dia. 12 mm. Burr dia. [mm] Rotational speeds [RPM]
Coarse stock removal on cast iron. 6 24,000 40,000
Cutting speed: 450–750 m/min
Rotational speed range: 10 14,000 24,000
12,000–20,000 RPM 12 12,000 20,000
48
TC burrs CAST cut

l2
PFERDVALUE: l1


[mm] [mm] [mm] [mm] CAST
EAN 4007220
Shank dia. 6 mm
6 16 6 55 952658 24,000–40,000 1 ZYAS 0616/6 CAST
10 20 6 60 952665 14,000–24,000 1 ZYAS 1020/6 CAST
12 25 6 65 952672 12,000–20,000 1 ZYAS 1225/6 CAST
Shank dia. 8 mm
12 25 8 65 067925 12,000–20,000 1 ZYAS 1225/8 CAST

l2
l1
PFERDVALUE:


EAN 4007220
Shank dia. 6 mm
10 9 6 49 952504 14,000–24,000 1 KUD 1009/6 CAST
12 10 6 51 952511 12,000–20,000 1 KUD 1210/6 CAST
Shank dia. 8 mm
12 10 8 51 068038 12,000–20,000 1 KUD 1210/8 CAST
49
TC burrs CAST cut

l2
PFERDVALUE:


EAN 4007220
Shank dia. 6 mm
6 16 6 55 952610 24,000–40,000 1 WRC 0616/6 CAST
10 20 6 60 952627 14,000–24,000 1 WRC 1020/6 CAST
12 25 6 65 952634 12,000–20,000 1 WRC 1225/6 CAST
Shank dia. 8 mm
12 25 8 65 067932 12,000–20,000 1 WRC 1225/8 CAST
Flame shape B d1 d2
l1
PFERDVALUE:


[mm] [mm] [mm] [mm] [mm] CAST
EAN 4007220
Shank dia. 6 mm
12 30 6 70 2.1 952450 12,000–20,000 1 B 1230/6 CAST
Shank dia. 8 mm
12 30 8 70 2.1 068021 12,000–20,000 1 B 1230/8 CAST
50
TC burrs CAST cut

l1
PFERDVALUE:


EAN 4007220
Shank dia. 6 mm
6 18 6 55 952580 24,000–40,000 1 SPG 0618/6 CAST
10 20 6 60 952597 14,000–24,000 1 SPG 1020/6 CAST
12 25 6 70 952603 12,000–20,000 1 SPG 1225/6 CAST
Shank dia. 8 mm
12 25 8 70 067956 12,000–20,000 1 SPG 1225/8 CAST

d1 d2
r l2
PFERDVALUE: l1


EAN 4007220
Shank dia. 6 mm
12 30 6 70 14° 2.6 952474 12,000–20,000 1 KEL 1230/6 CAST
Shank dia. 8 mm
12 30 8 70 14° 2.6 068014 12,000–20,000 1 KEL 1230/8 CAST
51
TC burrs CAST cut

Conical pointed burr according to DIN 8032, flattened tip. l2
l1
PFERDVALUE:

d1 l2 d2 l1 a Cut RPM Description

EAN 4007220
Shank dia. 6 mm
12 25 6 65 26° 952481 12,000–20,000 1 SKM 1225/6 CAST

PFERDVALUE: l1


EAN 4007220
Shank dia. 6 mm
6 18 6 55 1.5 952528 24,000–40,000 1 RBF 0618/6 CAST
10 20 6 60 2.5 952559 14,000–24,000 1 RBF 1020/6 CAST
12 25 6 65 2.5 952566 12,000–20,000 1 RBF 1225/6 CAST
Shank dia. 8 mm
12 25 8 65 2.5 067949 12,000–20,000 1 RBF 1225/8 CAST

l1
PFERDVALUE:


EAN 4007220
Shank dia. 6 mm
12 20 6 60 5.0 952467 12,000–20,000 1 TRE 1220/6 CAST
52
TC burrs TITANIUM cut
for use on titanium
The TITANIUM cut has been especially developed for work on hard titanium materials (tensile
strength over 500 N/mm²). It is characterized by an extremely high stock removal rate on this
material group, which has very challenging stock removal properties. Tungsten carbide burrs
with the TITANIUM cut impress with their smooth milling with considerably reduced vibration
and less noise.
Advantages: Recommendations for use:

■ Outstanding stock removal rate and tool ■ Determine the rotational speed in each Safety notes:
life due to the innovative tooth geometry. case depending on the titanium alloy you ■ The very high stock removal rate can cause
■ Significantly increased aggressiveness, need to machine. discolouration on the shank. This does not
large chips and very good chip removal. ■ Reduce the rotational speed if excessive constitute a safety risk.
■ Comfortable working with reduced flying sparks occur. Depending on the
vibration and less noise. titanium alloy you are machining, flying
■ Reduced wear on the tool drive due to sparks may not be entirely avoidable.
PFERDVALUE:
impact-free work without chatter marks, ■ If possible, use the tools on powerful drives PFERDERGONOMICS recommends burrs
thanks to the high concentricity. with elastically mounted spindles to avoid with TITANIUM cut as an innovative tool
vibration. solution for comfortable working with
Materials that can be worked: ■ For the cost-effective use of burrs, work significantly reduced vibration and less
with higher rotational/cutting speeds. noise.
■ Titanium Power recommendation for tool drives:
■ Hard titanium alloys - Shank diameter of 3 mm: 75 to 300
watts
Applications: - Shank diameter of 6 mm: from 300 watts
■ Please observe the rotational speed PFERDEFFICIENCY recommends burrs with
■ Milling out
recommendations. TITANIUM cut for long fatigue-free and
■ Levelling
■ Deburring resource-saving work with perfect results in a
■ Cutting out holes Matching tool drives: very short period of time.
■ Surface work ■ Flexible shaft drive
■ Work on weld seams ■ Straight grinder
■ Robot
■ Machine tools
PFERDVIDEO:
with TITANIUM cut.
53
for use on titanium


Coarse stock
Non-ferrous metals Hard non-ferrous metals Hard titanium alloys TITANIUM 250–450 m/min
removal

TC burr,
TITANIUM cut, ➋ 250 450
Coarse stock removal on hard titanium 3 27,000 48,000
alloys.
Cutting speed: 250–450 m/min 4 20,000 36,000
7,000–12,000 RPM 6 13,000 24,000
12 7,000 12,000
Note:
For soft titanium alloys (tensile strength under 500 N/mm²), we recommend tungsten
carbide burrs with the INOX cut. The special tooth geometry on these burrs prevents the
flutes becoming clogged, particularly for soft, lubricating materials (see page 34).
54
for use on titanium

l2
PFERDVALUE: l1


[mm] [mm] [mm] [mm] TITANIUM
EAN 4007220
Shank dia. 3 mm
3 13 3 43 034217 27,000–48,000 1 ZYAS 0313/3 TITANIUM
6 13 3 43 034224 13,000–24,000 1 ZYAS 0613/3 TITANIUM
Shank dia. 6 mm
6 16 6 55 034248 13,000–24,000 1 ZYAS 0616/6 TITANIUM
12 25 6 65 034255 7,000–12,000 1 ZYAS 1225/6 TITANIUM

l2
l1
PFERDVALUE:


EAN 4007220
Shank dia. 3 mm
3 2 3 33 034149 27,000–48,000 1 KUD 0302/3 TITANIUM
4 3 3 34 034163 20,000–36,000 1 KUD 0403/3 TITANIUM
5 4 3 35 034170 16,000–29,000 1 KUD 0504/3 TITANIUM
6 5 3 35 034187 13,000–24,000 1 KUD 0605/3 TITANIUM
Shank dia. 6 mm
6 5 6 45 034194 13,000–24,000 1 KUD 0605/6 TITANIUM
12 10 6 51 034200 7,000–12,000 1 KUD 1210/6 TITANIUM
55
for use on titanium

l2
PFERDVALUE:


EAN 4007220
Shank dia. 3 mm
3 13 3 43 034309 27,000–48,000 1 WRC 0313/3 TITANIUM
6 13 3 43 034316 13,000–24,000 1 WRC 0613/3 TITANIUM
Shank dia. 6 mm
6 16 6 55 034330 13,000–24,000 1 WRC 0616/6 TITANIUM
12 25 6 65 034347 7,000–12,000 1 WRC 1225/6 TITANIUM

l2
PFERDVALUE: l1


EAN 4007220
Shank dia. 3 mm
3 7 3 37 034323 27,000–48,000 1 SPG 0307/3 TITANIUM
13 3 43 034392 27,000–48,000 1 SPG 0313/3 TITANIUM
6 13 3 43 034408 13,000–24,000 1 SPG 0613/3 TITANIUM
Shank dia. 6 mm
6 18 6 55 034415 13,000–24,000 1 SPG 0618/6 TITANIUM
12 25 6 65 034422 7,000–12,000 1 SPG 1225/6 TITANIUM
56
for use on titanium

l1
PFERDVALUE:


[mm] [mm] [mm] [mm] [mm] TITANIUM
EAN 4007220
Shank dia. 3 mm
3 13 3 43 0.75 034354 27,000–48,000 1 RBF 0313/3 TITANIUM
6 13 3 43 1.5 034361 13,000–24,000 1 RBF 0613/3 TITANIUM
Shank dia. 6 mm
6 18 6 55 1.5 034378 13,000–24,000 1 RBF 0618/6 TITANIUM
12 25 6 65 2.5 034385 7,000–12,000 1 RBF 1225/6 TITANIUM
57
TC burrs PLAST, FVK and FVKS cut
for work on GRP/CRP
Tungsten carbide burrs with the PLAST, FVK and FVKS cuts are suitable for trimming and
contour milling on a wide range of fibre-reinforced plastics (GRP/CRP).
Burrs with a drill cut (BS) or with a centre drill (ZBS) allow combined drilling and milling work.
Burrs with an end cut (two teeth, STS) enable holes to be drilled with minimal burr formation,
whilst the version with a flat end cut (two teeth, FSTS) is used to mill grooves and pockets.
The STS and FSTS versions are suitable only for machine and robot applications. The special
tooth geometry allows high feed rates due to the low resistance. In addition, these burrs are
characterized by smooth milling.
Advantages: ■ Select a burr diameter greater than the Applications:

thickness of the material to be machined,
■ Reduced wear on the tool drive due to to avoid impacts and chattering with the ■ Trimming
impact-free work without chatter marks, risk of damaging or breaking the tool. ■ Contour milling
thanks to the high concentricity. ■ Increase the rotational speed if the tool ■ Deburring
tends to chatter. ■ Milling grooves and pockets (with FSTS)
Recommendations for use: ■ If necessary, reduce the rotational speed ■ Drilling blind holes (with FSTS)
and contact pressure if melting occurs. ■ Drilling with minimal burr formation
■ The version with a drill cut (BS) is (with STS)
■ If possible, use the tools on powerful drives
particularly suitable for machine and ■ Milling out
robot applications, while the version with ■ Cutting out holes
vibration.
a centre drill (ZBS) is used for manual
■ For the cost-effective use of burrs, work
applications. It allows secure drilling on
with higher rotational/cutting speeds. Matching tool drives:
almost all surface conditions.
■ The versions with an end cut (two teeth, ■ Flexible shaft drive
- Shank diameter of 3 mm: 75 to
STS) and flat end cut (two teeth, FSTS) ■ Straight grinder
300 watts
are suitable only for machine and robot ■ Robot
- Shank diameter of 6 mm: from 300 watts
applications. ■ Machine tools
recommendations.
PLAST cut
Advantages: PFERDVALUE:
■ Particularly suitable for GRP and CRP with PFERDERGONOMICS recommends burrs
up to 40 % fibre content. with PLAST cut as an innovative tool solution
■ Minimizes delamination and fraying due to for comfortable working with significantly
the special cut that is similar to PCD mills. reduced vibration and less noise.
Tungsten carbide burrs with the PLAST cut ■ Particularly suitable for use on machines
are particularly suitable for use on less hard and on robots
glass and carbon-fibre-reinforced duroplas- ■ Very low cutting force.
tics (GRP and CRP with up to 40 % fibre ■ High feed rates.
content) and fibre-reinforced thermoplastics. PFERDEFFICIENCY recommends burrs with
The cut (similar to PCD milling) minimizes Materials that can be worked: PLAST cut for long fatigue-free and resource-
delamination and fraying. saving work with perfect results in a very
■ Plastics short period of time.
■ Fibre-reinforced plastics (GRP/CRP) with a
PFERDVIDEO: fibre content up to 40 %
■ Thermoplastics
with PLAST cut.
Cut FVK Cut FVKS

Advantages:
■ Particularly suitable for GRP and CRP, also
with over 40 % fibre content.
■ The FVKS cut produces smooth edges and
Tungsten carbide burrs with the FVK and FVKS cuts are suitable for universal use on hard glass is characterized by smooth milling.
and carbon-fibre-reinforced duroplastics. Due to its high concentricity, the FVK cut is suitable
for tool machines and manual applications. It is characterized by smooth milling and produces Materials that can be worked:
a smooth EDGE cut. The FVKS cut is suitable for use on machines and robots with high feed ■ Plastics
rates. ■ Fibre-reinforced plastics (GRP/CRP) with a
fibre content over 40 %
58
TC burrs PLAST, FVK and FVKS cut
for work on GRP/CRP


Thermoplastics, fibre-rein-
forced plastics (GRP/CRP) with Trimming, PLAST
Plastics, a fibre content up to 40 % contour mill-
other ing, cutting 450–900 m/min
materials Fibre-reinforced plastics out holes, FVK
(GRP/CRP) with a fibre content deburring
over 40 % FVKS

TC burr, ➋
PLAST cut, Burr dia. 450 900
Trimming plastics. 6 24,000 48,000
18,000–36,000 RPM
Cylindrical shape ZYA BS d1 d2

Cylindrical burr. l2
l1
Ordering notes:
■ Please complete the description with the ZBS d3
desired cut.
STS
PFERDVALUE:
PLAST cut:
FSTS

d1 l2 d2 l1 Centre Cut RPM Description

[mm] [mm] [mm] [mm] drill dia. PLAST FVK FVKS
d3
[mm]
EAN 4007220
Shank dia. of 6 mm with drill cut (BS)
6 25 6 65 - 900413 050217 808900 24,000–48,000 1 ZYA 0625/6 ... BS
Shank dia. of 8 mm with drill cut (BS)
8 25 8 65 - 900468 050231 808917 18,000–36,000 1 ZYA 0825/8 ... BS
Shank dia. of 6 mm with centre drill (ZBS)
6 25 6 65 2.5 900451 869048 869055 24,000–48,000 1 ZYA 0625/6 ... ZBS
Shank dia. 6 mm with end cut (STS)
6 25 6 65 - 003107 - - 24,000–48,000 1 ZYA 0625/6 ... STS
Shank dia. 8 mm with end cut (STS)
8 25 8 65 - 003121 - - 18,000–36,000 1 ZYA 0825/8 ... STS
Shank dia. 6 mm with flat end cut (FSTS)
6 25 6 65 - 003138 - - 24,000–48,000 1 ZYA 0625/6 ... FSTS
Shank dia. 8 mm with flat end cut (FSTS)
8 25 8 65 - 003152 - - 18,000–36,000 1 ZYA 0825/8 ... FSTS
59
TC burrs TOUGH and TOUGH-S cut
for tough applications
The TOUGH and TOUGH-S cuts have been specially designed for tough operating conditions TOUGH cut
in dockyards, foundries and steel construction. They are also ideal for use in all manufacturing
sectors where, due to the difficult production environment, tooth breakages or other damage
to conventional burrs is a frequent occurrence.
Advantages: Materials that can be worked:

■ Innovative, special cuts providing excep- ■ Cast iron
tional impact resistance. ■ Steel
■ Minimized tooth chipping/breakage, ■ Cast steel Tungsten carbide burrs with the TOUGH
splintering and burr failures due to very ■ The TOUGH and TOUGH-S cuts can be cut are particularly aggressive and are
robust, high-performance cuts. used on materials up to 54 HRC. For harder characterized by high stock removal.
■ Can also be used at low rotational speeds. materials, it is recommended to perform
■ Due to their extreme impact resistance, trials beforehand. TOUGH-S cut
they can perfectly be used as long-shank
variants. Recommendations for use:
■ Reduced wear on the tool drive due to
impact-free work without chatter marks, ■ For the cost-effective use of burrs, work
thanks to the high concentricity. with higher rotational/cutting speeds.
Applications: - Shank diameter of 3 mm: 75 to
300 watts Tungsten carbide burrs with the TOUGH-S
■ High-impact applications when using - Shank diameter of 6 mm: from 300 watts cut are characterized by smooth milling and
shank extensions ■ Please observe the rotational speed high stock removal.
■ Applications with a high angle of surface recommendations.
contact PFERDVIDEO:
■ Milling of narrow contours Matching tool drives:
■ Applications where high rotational speeds Learn more about the advantages
are not available ■ Flexible shaft drive of using tungsten carbide burrs
■ Straight grinder with TOUGH and TOUGH-S cuts.
Recommended rotational speed range [RPM] Safety note:

To determine the recommended cutting To determine the recommended rotational Please observe the reduced
speed range [m/min], please proceed as speed range [RPM], please proceed as rotational speeds for burrs with a
follows: follows: long shank. They can be found on
➊ Select the material group to be machined. ➍ Select the required burr diameter. page 6.

Construction steels, carbon steels, TOUGH
Steels up to
tool steels, non-alloyed steels, case-
1,200 N/mm² 250–600 m/min
hardened steels, cast steel, alloyed Coarse stock TOUGH-S
Steel, (up to 38 HRC)
steels removal with
cast steel
Hardened, heat-treated impact load TOUGH
Tool steels, tempering steels, alloyed
steels over 1,200 N/mm² 250–350 m/min
steels, cast steel TOUGH-S
(over 38 HRC)
Cast iron with flake graphite EN-GJL
(GG), with nodular graphite/nodular Coarse stock TOUGH
Grey cast iron,
Cast iron cast iron EN-GJS (GGG), white an- removal with 250–600 m/min
white cast iron
nealed cast iron EN-GJMW (GTW), impact load TOUGH-S

TC burr,
TOUGH cut, ➍ 250 350 600
Coarse stock removal with impact load on 8 10,000 14,000 24,000
steels up to 1,200 N/mm².
Rotational speed range: 12 7,000 9,000 16,000
7,000–16,000 RPM 16 5,000 7,000 12,000
60

Cylindrical burr according to DIN 8032.
l2
Ordering notes: l1
desired cut.
[mm] [mm] [mm] [mm] TOUGH TOUGH-S
EAN 4007220
Shank dia. 6 mm
8 20 6 60 895504 - 1 ZYA 0820/6 ...
10 20 6 60 895658 - 1 ZYA 1020/6 ...
12 25 6 65 895665 895672 1 ZYA 1225/6 ...

l1
[mm] [mm] [mm] [mm] TOUGH
EAN 4007220
Shank dia. 6 mm
8 20 6 60 769997 1 ZYAS 0820/6 TOUGH
10 20 6 60 770023 1 ZYAS 1020/6 TOUGH
12 25 6 65 869109 1 ZYAS 1225/6 TOUGH
Shank dia. 8 mm
12 25 8 65 770054 1 ZYAS 1225/8 TOUGH
61

l2
l1
[mm] [mm] [mm] [mm] TOUGH
EAN 4007220
Shank dia. 6 mm
8 7 6 47 955383 1 KUD 0807/6 TOUGH
12 10 6 51 770160 1 KUD 1210/6 TOUGH

l2
Ordering notes:
desired cut.
Safety notes:
Please observe the reduced
rotational speeds for burrs with a
=
long shank. They can be found on
page 6.
EAN 4007220
Shank dia. 6 mm
8 20 6 60 770108 - 1 WRC 0820/6 ...
10 20 6 60 770115 - 1 WRC 1020/6 ...
12 25 6 65 770122 770139 1 WRC 1225/6 ...
12 25 6 175 091043 - 1 WRC 1225/6 ... SL 150
Shank dia. 8 mm
12 25 8 65 769881 - 1 WRC 1225/8 ...
62
Flame shape B d1 d2
l1
[mm] [mm] [mm] [mm] [mm] TOUGH
EAN 4007220
Shank dia. 6 mm
8 20 6 60 1.5 770061 1 B 0820/6 TOUGH
12 30 6 70 2.1 770085 1 B 1230/6 TOUGH
Shank dia. 8 mm
12 30 8 70 2.1 770092 1 B 1230/8 TOUGH

Ordering notes:
desired cut.
Safety notes:
=
page 6.
EAN 4007220
Shank dia. 6 mm
10 20 6 60 770252 770269 1 SPG 1020/6 ...
12 25 6 65 770276 - 1 SPG 1225/6 ...
12 25 6 175 090930 - 1 SPG 1225/6 ... SL 150
Shank dia. 8 mm
12 25 8 65 770283 - 1 SPG 1225/8 ...
63

d1 d2
SL = shank length (long steel shank) r l2
l1
Safety notes:
=
page 6.
EAN 4007220
Shank dia. 6 mm
12 25 6 65 14° 3.3 770320 1 KEL 1225/6 TOUGH
12 25 6 175 14° 3.3 091166 1 KEL 1225/6 TOUGH SL 150
Shank dia. 8 mm
12 25 8 65 14° 3.3 770337 1 KEL 1225/8 TOUGH

Ordering notes:
desired cut.
Safety notes:
=
page 6.
[mm] [mm] [mm] [mm] [mm] TOUGH TOUGH-S
EAN 4007220
Shank dia. 6 mm
8 20 6 60 1.2 770191 - 1 RBF 0820/6 ...
10 20 6 60 2.5 770207 - 1 RBF 1020/6 ...
12 25 6 65 2.5 770214 770238 1 RBF 1225/6 ...
16 25 6 65 4.9 869116 - 1 RBF 1625/6 ...
12 25 6 175 2.5 090947 - 1 RBF 1225/6 ... SL 150
Shank dia. 8 mm
12 25 8 65 2.5 770221 770245 1 RBF 1225/8 ...
64

l1
EAN 4007220
Shank dia. 6 mm
10 16 6 56 4.0 770344 1 TRE 1016/6 TOUGH
12 20 6 60 5.0 770351 1 TRE 1220/6 TOUGH
Set 1712 TOUGH

Set 1712 TOUGH contains five tungsten carbide burrs for tough applications in the most
damage.
Contents:
shank dia. 6 mm, TOUGH cut
1 piece each:
■ WRC 1225/6 TOUGH
■ SPG 1225/6 TOUGH
■ RBF 1225/6 TOUGH
■ KEL 1225/6 TOUGH
■ TRE 1220/6 TOUGH
Cut Description
TOUGH
EAN 4007220
Shank dia. 6 mm
955635 1 1712 TOUGH
65
TC burrs MICRO cut
for finishing work
Tungsten carbide burrs with the MICRO cut are specifically designed for finishing and are used
in areas in which mounted grinding points are usually used. They offer a higher stock removal
rate and produce a high surface quality, particularly compared with conventionally milled
surfaces. They also operate with low vibration and little noise. They maintain their geometry
over their entire tool life, and are well suited to manual and machine applications. Almost all
materials up to a hardness of 68 HRC can be machined.

PFERDVALUE:
■ High surface quality. ■ If possible, use the tools on powerful drives
■ Unlike with mounted grinding points, with elastically mounted spindles to avoid PFERDERGONOMICS recommends burrs
there is no change in geometry due to vibration. with MICRO cut as an innovative tool solu-
wear and tear. ■ For the cost-effective use of burrs, work tion for comfortable working with signifi-
■ Work on almost all materials up to with higher rotational/cutting speeds. cantly reduced vibration and less noise.
68 HRC. Power recommendation for tool drives:
■ Reduced wear on the tool drive due to - Shank diameter of 3 mm: 75 to
impact-free work without chatter marks, 300 watts
thanks to the high concentricity. - Shank diameter of 6 mm: from 300 watts
■ Please observe the rotational speed PFERDEFFICIENCY recommends burrs
Applications: recommendations. with MICRO cut for long fatigue-free and
resource-saving work with perfect results in a
■ Finishing Matching tool drives: very short period of time.
■ Very fine cleaning work
■ Corrections in tool and mould construction ■ Flexible shaft drive
■ Sharpening cutting tools ■ Straight grinder
■ Robot applications
Materials that can be worked: ■ Machine tools
PFERDVIDEO:
■ Steel and cast steel
■ Stainless steel (INOX) Learn more about the advantages
■ Non-ferrous metals of using tungsten carbide burrs
■ Cast iron with MICRO cut.
66
TC burrs MICRO cut
for finishing work

follows: follows:
➊ Select the material group to be machined. ➌ Select the required burr diameter.
➋ Establish the cutting speed range. ➍ The cutting speed range and the burr
diameter determine the recommended
➊ Material group Application Cut ➋ Cutting speed

Steels up to Construction steels, carbon steels, tool
1,200 N/mm² steels, non-alloyed steels, case-hardened 600–750 m/min
(up to 38 HRC) steels, cast steel, alloyed steels
Steel,
Hardened, Fine stock removal MICRO
cast steel
heat-treated steels over Tool steels, tempering steels,
450–600 m/min
1,200 N/mm² alloyed steels, cast steel
(over 38 HRC)
Stainless
Rust and acid-resistant
steel Austenitic and ferritic stainless steels Fine stock removal MICRO 450–600 m/min
steels
(INOX)
Bronze, titanium/titanium alloys,
Non- Hard non-ferrous metals
hard aluminium alloys (high Si content)
ferrous Fine stock removal MICRO 450–600 m/min
metals High-temperature- Nickel-based and cobalt-based alloys
resistant materials (engine and turbine construction)
Cast iron with flake graphite EN-GJL (GG),
with nodular graphite/nodular cast iron
Grey cast iron,
Cast iron EN-GJS (GGG), white annealed cast iron Fine stock removal MICRO 600–750 m/min
white cast iron
EN-GJMW (GTW), black cast iron EN-
GJMB (GTS)
Example: ➍ Cutting speeds [m/min]

TC burr, ➌
MICRO cut, Burr dia. 450 600 750
Fine stock removal on steels 2 72,000 95,000 120,000
up to 1,200 N/mm².
Rotational speed range: 4 36,000 48,000 60,000
19,000–24,000 RPM 6 24,000 32,000 40,000
8 18,000 24,000 30,000
10 14,000 19,000 24,000
12 12,000 16,000 20,000
67
TC burrs MICRO cut
for finishing work

l1
PFERDVALUE:

[mm] [mm] [mm] [mm] MICRO
EAN 4007220
Shank dia. 3 mm
2 10 3 40 895511 1 ZYA 0210/3 MICRO
3 13 3 43 895535 1 ZYA 0313/3 MICRO
4 13 3 43 895542 1 ZYA 0413/3 MICRO
6 13 3 43 953068 1 ZYA 0613/3 MICRO
Shank dia. 6 mm
6 16 6 55 895559 1 ZYA 0616/6 MICRO
8 20 6 60 895573 1 ZYA 0820/6 MICRO
10 20 6 60 895603 1 ZYA 1020/6 MICRO
12 25 6 65 953051 1 ZYA 1225/6 MICRO

l1
PFERDVALUE:

EAN 4007220
Shank dia. 6 mm
6 16 6 55 895566 1 ZYAS 0616/6 MICRO
8 20 6 60 895580 1 ZYAS 0820/6 MICRO
10 20 6 60 895610 1 ZYAS 1020/6 MICRO
12 25 6 65 953105 1 ZYAS 1225/6 MICRO
68
TC burrs MICRO cut
for finishing work

l2
l1
PFERDVALUE:

EAN 4007220
Shank dia. 3 mm
2 1.5 3 33 895399 1 KUD 021,5/3 MICRO
3 2 3 33 895405 1 KUD 0302/3 MICRO
4 3 3 34 895412 1 KUD 0403/3 MICRO
6 5 3 35 953129 1 KUD 0605/3 MICRO
Shank dia. 6 mm
6 5 6 45 895436 1 KUD 0605/6 MICRO
8 7 6 47 895474 1 KUD 0807/6 MICRO
10 9 6 49 895481 1 KUD 1009/6 MICRO
12 10 6 51 953112 1 KUD 1210/6 MICRO

l2
PFERDVALUE:

EAN 4007220
Shank dia. 3 mm
2 10 3 40 953167 1 WRC 0210/3 MICRO
3 13 3 43 869000 1 WRC 0313/3 MICRO
6 13 3 43 953150 1 WRC 0613/3 MICRO
Shank dia. 6 mm
6 16 6 55 869017 1 WRC 0616/6 MICRO
8 20 6 60 869024 1 WRC 0820/6 MICRO
10 20 6 60 869031 1 WRC 1020/6 MICRO
12 25 6 65 953136 1 WRC 1225/6 MICRO
69
TC burrs MICRO cut
for finishing work

l1
PFERDVALUE:

EAN 4007220
Shank dia. 3 mm
3 7 3 37 003886 1 SPG 0307/3 MICRO
13 3 43 003893 1 SPG 0313/3 MICRO
6 13 3 43 003909 1 SPG 0613/3 MICRO
Shank dia. 6 mm
6 18 6 55 003916 1 SPG 0618/6 MICRO
8 20 6 60 003923 1 SPG 0820/6 MICRO
10 20 8 60 003930 1 SPG 1020/6 MICRO
12 25 6 65 003954 1 SPG 1225/6 MICRO

Conical pointed burr according to DIN 8032, flattened tip.
l2
PFERDVALUE: l1

EAN 4007220
Shank dia. 3 mm
3 7 3 37 21° 067833 1 SKM 0307/3 MICRO
11 3 41 14° 067864 1 SKM 0311/3 MICRO
6 13 3 43 25° 067871 1 SKM 0613/3 MICRO
Shank dia. 6 mm
6 18 6 55 18° 067888 1 SKM 0618/6 MICRO
8 20 6 60 22° 067895 1 SKM 0820/6 MICRO
10 20 6 60 28° 067901 1 SKM 1020/6 MICRO
12 25 6 65 26° 067918 1 SKM 1225/6 MICRO
70
TC burrs MICRO cut
for finishing work

l1
PFERDVALUE:

[mm] [mm] [mm] [mm] [mm] MICRO
EAN 4007220
Shank dia. 3 mm
3 7 3 37 0.75 835524 1 RBF 0307/3 MICRO
13 3 43 0.75 955352 1 RBF 0313/3 MICRO
6 13 3 43 1.5 955338 1 RBF 0613/3 MICRO
Shank dia. 6 mm
6 18 6 55 1.5 835494 1 RBF 0618/6 MICRO
8 20 6 60 1.2 835500 1 RBF 0820/6 MICRO
10 20 6 60 2.5 835517 1 RBF 1020/6 MICRO
12 25 6 65 2.5 953143 1 RBF 1225/6 MICRO
Set 1502 MICRO

Set 1502 MICRO contains ten small tungsten carbide burrs for finishing work in the most
damage.
shank dia. 3 mm, MICRO cut
1 piece each:
■ ZYA 0210/3 MICRO ■ WRC 0613/3 MICRO
■ ZYA 0313/3 MICRO ■ KUD 0302/3 MICRO
■ ZYA 0613/3 MICRO ■ KUD 0605/3 MICRO
■ WRC 0210/3 MICRO ■ RBF 0307/3 MICRO
■ WRC 0313/3 MICRO ■ RBF 0613/3 MICRO
Cut Description
MICRO
EAN 4007220
Shank dia. 3 mm
896181 1 1502 MICRO
71
TC burrs MICRO cut
for finishing work
Set 1303 MICRO

The 1303 MICRO set contains three small tungsten carbide burrs for finishing in the most
damage.
1 piece each:
■ ZYA 0313/3 MICRO
■ WRC 0313/3 MICRO
■ RBF 0313/3 MICRO
Cut Description
MICRO
EAN 4007220
Shank dia. 3 mm
226667 1 1303 MICRO
Set 1306 MICRO

The 1306 MICRO set contains three tungsten carbide burrs for finishing in the most common
shapes and dimensions. The sturdy plastic box protects the tools from dirt and damage.
1 piece each:
■ ZYAS 0616/6 MICRO
Cut Description
MICRO
EAN 4007220
Shank dia. 6 mm
226674 1 1306 MICRO
Set 1312 MICRO

The 1312 MICRO set contains three tungsten carbide burrs for finishing in the most common
shapes and dimensions. The sturdy plastic box protects the tools from dirt and damage.
1 piece each:
■ ZYAS 1225/6 MICRO
Cut Description
MICRO
EAN 4007220
Shank dia. 6 mm
226681 1 1312 MICRO
72
TC burrs EDGE cut
for defined work on edges
Tungsten carbide burrs for work on edges represent a separate PFERD product line. They are
mainly used in steel and aluminium construction and have been specifically designed for
chamfering, deburring and rounding of edges. PFERD offers tools for both flexible as well as
for defined work on edges.
Materials that can be worked: Matching tool drives:

■ Steel and cast steel ■ Flexible shaft drive
■ Stainless steel (INOX) ■ Straight grinder
■ Non-ferrous metals ■ Robot
■ Cast iron ■ Machine tools
■ Plastics, other materials
Defined work on edges with the EDGE cut

Tungsten carbide burrs with the EDGE cut have been especially developed for defined work
on edges. The special design allows the burr to run directly along the edges without damag-
ing the workpiece. Exact edge shapes can therefore be created in a single step – with either
defined chamfers of 30° or 45°, or to a defined radius of 3.0 mm. Among other things, round-
ing edges is a precautionary measure for anti-corrosion protection according to ISO 12944-3,
ISO 8501-3, SOLAS XII/6.3 (Ref. T4/3.01 MSC.1/Circ.1198).

■ Special design for precise guidance. ■ Use the burrs counterrotationally. In order
■ Safe and comfortable to guide. to produce a fine surface, finally pass them
■ Create exact edge shapes in a single step. over the edges in the direction of rotation.
Applications: PFERDVALUE: PFERDVIDEO:

■ Defined work on edges PFERDEFFICIENCY recommends burrs with Learn more about the advantages
■ Defined deburring EDGE cut for long fatigue-free and resource- of using tungsten carbide burrs
■ Breaking and rounding edges in steel and saving work with perfect results in a very with EDGE cut.
aluminium construction short period of time.
■ Rounding edges in preparation for the
application of anti-corrosion coatings in
shipbuilding, on crane systems and other
steel constructions which are exposed to
corrosion loading
■ Defined chamfering for weld seam
preparation for V-shaped seams (60°,
ISO 9692-1)
■ Defined chamfering for edge breaking
(45°)
EDGE Cutting System (ECS)
The EDGE Cutting System consists of burrs Advantages:

with the EDGE cut and a special guide
sleeve. The system can be positioned on ■ Improved guidance.
any conventional drive to ensure optimal ■ Can be used with any conventional
guidance during light deburring work (see straight grinder.
pages 75–76). ■ Burr is interchangeable.
73
TC burrs EDGE cut

follows: follows:
➊ Select the material group to be machined. ➍ Select the required burr diameter.

Construction steels, carbon steels, tool
Steels up to 1,200 N/mm²
steels, non-alloyed steels, case-hardened 600–900 m/min
(up to 38 HRC)
Steel, steels, cast steel, alloyed steels Work on
EDGE
cast steel Hardened, heat-treated edges
Tool steels, tempering steels, alloyed
steels over 1,200 N/mm² 600–750 m/min
steels, cast steel
(over 38 HRC)
Soft aluminium alloys Work on EDGE ALU 900–1,100 m/min
Soft non-ferrous metals
Brass, copper, zinc edges EDGE 600–900 m/min
Bronze, hard aluminium alloys
Non-ferrous Work on EDGE ALU 900–1,100 m/min
Hard non-ferrous metals (high Si content)
metals edges
Titanium/titanium alloys EDGE 250–450 m/min
Nickel-based and cobalt-based alloys Work on
Hochwarmfeste Werkstoffe EDGE 250–450 m/min
(engine and turbine construction) edges
Plastics, Work on
Fibre-reinforced plastics (GRP/CRP), thermoplastics EDGE ALU 750–1,100 m/min
other materials edges

TC burr, ➍
EDGE cut, Burr dia. 250 350 450 600 750 900 1,100
Machining steels up to 1,200 N/mm². 16 5,000 7,000 9,000 12,000 15,000 18,000 22,000
Rotational speed range:
12,000–18,000 RPM
74
TC burrs EDGE cut
Conical counterbore shape KSJ EDGE α
Conical counterbore burr for the production of precisely defined chamfers. Suitable for d1 d3 d2
chamfering of defined 30° chamfer angles.
l2
Ordering notes: l3
■ Please complete the description with the l1
desired cut.
PFERDVALUE:

d1 l2 d2 l1 d3 l3 a Cut Description
[mm] [mm] [mm] [mm] [mm] [mm] EDGE EDGE ALU
EAN 4007220
Shank dia. 6 mm
16 5 6 54 10 14 60° 952443 098011 1 KSJ 1605/6 ... 30°
Conical counterbore shape KSK EDGE α
Conical counterbore burr for the production of precisely defined chamfers. Suitable for cham- d1 d3 d2
fering of defined 45° chamfer angles. The chamfers created using the EDGE Cutting System
(ECS) are 1.2 mm (+/- 0.2 mm) wide. l2
l3
Ordering notes: l1
■ The EDGE Cutting System (ECS) burr can
be reordered and replaced if required.
Matching burr: KSK 1603/6 EDGE ALU 45°. d4
desired cut. l2
l3
PFERDVALUE:
d1 l2 d2 l1 d3 l3 d4 a Cut Description
[mm] [mm] [mm] [mm] [mm] [mm] [mm] EDGE EDGE ALU
EAN 4007220
Shank dia. 6 mm
16 3 6 52 10 12 - 90° 952436 098004 1 KSK 1603/6 ... 45°
1 6 52 10 24 25 90° 097984 097991 1 KSK 1603/6 ... 45° ECS
75
TC burrs EDGE cut
Concave radius burrs V EDGE r
Concave radius burrs for the production of precise radii. Cannot be re-sharpened. Suitable for d1 d3 d2
the production and processing of 3 mm outer radii.
l2
Ordering notes: l3
■ The EDGE Cutting System (ECS) burr can l1
be reordered and replaced if required.
Matching burr: V 1612/6 EDGE R3,0. d4
PFERDVALUE:
l2
l3
d1 l2 d2 l1 d3 l3 d4 r Cut Description
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] EDGE
EAN
4007220
Shank dia. 6 mm
16 3 6 52 10 12 - 3.0 952412 1 V 1612/6 EDGE R3,0
24 25 3.0 098028 1 V 1612/6 EDGE R3,0 ECS
Subject to technical modifications.

03/2022
www.pferd.com · [email protected]
PFERD quality certified according to ISO 9001.
76

Catálogo Pferd Limas Rotativas HP-TC en

Uploaded by

Copyright:

Available Formats

Catálogo Pferd Limas Rotativas HP-TC en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catálogo Pferd Limas Rotativas HP-TC en

Uploaded by

Copyright:

Available Formats

Tungsten carbide burrs

for high-performance applications

■ Optimum stock removal rate, high aggressiveness and good guidance

Tungsten carbide burrs with HICOAT coating

Application Material group Application High-performance Page

Construction steels, carbon steels, STEEL 23

Recommendations for use: Safety notes:

■ If possible, use the tools on powerful drives with elastically mounted

■ In general, burrs are used counter­rotationally or with a swinging

Example: ➌ Maximum ➋ Maximum

Extensions for drive spindles

Recommended rotational speed range [RPM]

➊ Material group ➋ Application ➌ Cut ➍ Cutting speed

Example: ➏ Cutting speeds [m/min]

Cylindrical shape ZYA without end cut d1 d2

Ball shape KUD d1 d2

Cylindrical shape with radius end WRC d1 d2

Pointed tree shape SPG d1 d2

Conical shape with radius end KEL α

Conical pointed shape SKM d1 α d2

Tree shape with radius end RBF d1 d2

Oval shape TRE d1 d2

Advantages: Applications: Safety note:

recommendations. very short period of time.

Matching tool drives:

ALLROUND cut ALLROUND cut with

Recommended rotational speed range [RPM]

➊ Material group Application ➋ Cut ➌ Cutting speed

Example: ➎ Cutting speeds [m/min]

Cylindrical shape ZYAS with end cut d1 d2

Ball shape KUD d1 d2

Cylindrical shape with radius end WRC d1 d2

Pointed tree shape SPG d1 d2

Conical shape with radius end KEL α

Conical pointed shape SKM d1 α d2

Tree shape with radius end RBF d1 d2

Oval shape TRE d1 d2

Set 1412 ALLROUND

Set 1403 ALLROUND

Set 1404 ALLROUND

Set 1406 ALLROUND

Set 1414 ALLROUND

Set 1414 ALLROUND HC-FEP

Advantages: Materials that can be worked: PFERDVALUE:

STEEL cut STEEL cut with

Recommended rotational speed range [RPM] Safety note:

Material group Application ➊ Cut ➊ Cutting speed

Example: ➍ Cutting speeds [m/min]

Cylindrical shape ZYA without end cut d1 d2

d1 l2 d2 l1 Cut RPM Description

Cylindrical shape ZYAS with end cut d1 d2

d1 l2 d2 l1 Cut RPM Description

Ball shape KUD d1 d2

d1 l2 d2 l1 Cut RPM Description

Cylindrical shape with radius end WRC d1 d2

d1 l2 d2 l1 Cut RPM Description

d1 l2 d2 l1 r Cut RPM Description

Pointed tree shape SPG d1 d2

d1 l2 d2 l1 Cut RPM Description

■ In general, burrs are used counterrotationally or with a swinging