Mn00224e E

ALS - ALCplus2
Access Link Series
User manual
MN.00224.E - 001
Volume 1/1
The information contained in this handbook is subject to change without notice.
Property of Siae Microelettronica S.p.A. All rights reserved according to the law and according to the inter-
national regulations. No part of this document may be reproduced or transmitted in any form or by any
means, electronic or mechanical, without written permission from Siae Microelettronica S.p.A.
Unless otherwise specified, reference to a Company, name, data and address produced on the screen dis-
played is purely indicative aiming at illustrating the use of the product.
MS-DOS®, MS Windows® are trademarks of Microsoft Corporation.
HP®, HP OpenView NNM and HP–UX are Hewlett Packard Company registered trademarks.
UNIX is a UNIX System Laboratories registered trademark.
Oracle® is a Oracle Corporation registered trademark.
Linux term is a trademark registered by Linus Torvalds, the original author of the Linux operating system.
Linux is freely distributed according the GNU General Public License (GPL).
Other products cited here in are constructor registered trademarks.
Contents
Section 1.
USER GUIDE 7
1 DECLARATION OF CONFORMITY ............................................................................... 7
2 FIRST AID FOR ELECTRICAL SHOCK AND SAFETY RULES .......................................... 8

2.1 FIRST AID FOR ELECTRICAL SHOCK ..................................................................... 8
2.1.1 Artificial respiration .................................................................................. 8
2.1.2 Treatment of burns .................................................................................. 8
2.2 SAFETY RULES .................................................................................................. 9
2.3 CORRECT DISPOSAL OF THIS PRODUCT (Waste electrical & electronic equipment) ....11
2.4 INTERNAL BATTERY ..........................................................................................11
3 PURPOSE AND STRUCTURE OF THE MANUAL ............................................................12

3.1 PURPOSE OF THE MANUAL .................................................................................12
3.2 AUDIENCE BASIC KNOWLEDGE ..........................................................................12
3.3 STRUCTURE OF THE MANUAL .............................................................................12
Section 2.
DESCRIPTIONS AND SPECIFICATION 15
4 ABBREVIATION LIST................................................................................................15
4.1 LIST OF ABBREVIATIONS...................................................................................15
5 SYSTEM PRESENTATION ..........................................................................................17

5.1 RECOMMENDATION ..........................................................................................17
5.2 SYSTEM ARCHITECTURE ....................................................................................17
5.3 ALCplus2 modular IDU ........................................................................................17
5.3.1 LIM .......................................................................................................18
5.3.2 RIM.......................................................................................................18
5.4 ALCplus2 compact IDU ......................................................................................18
5.5 ODU ...............................................................................................................19
5.6 Management ....................................................................................................19
5.6.1 Hardware platform ..................................................................................19
5.6.2 Management ports ..................................................................................20
5.6.2.1 Q3/1 and Q3/2 ........................................................................20
ALS - ALplus2, ALCplus2 - MN.00224.E - 001 1

5.6.2.2 RS232 ....................................................................................20
5.6.2.3 LCT USB .................................................................................20
5.6.3 Protocols ...............................................................................................20
6 TECHNICAL SPECIFICATIONS ..................................................................................23

6.1 IDU CHARACTERISTISC .....................................................................................23
6.1.1 Traffic interfaces .....................................................................................23
6.1.1.1 2 Mbit/s (E1 G.703) ..................................................................23
6.1.1.2 STM1 electrical ........................................................................24
6.1.1.3 STM1 optical............................................................................24
6.1.1.4 Ethernet interface ....................................................................25
6.1.2 Service channels.....................................................................................27
6.1.2.1 2 Mbit/s (E1 G.703) wayside......................................................27
6.1.2.2 64 kbit/s codirectional...............................................................28
6.1.2.3 64 kbit/s contradirectional .........................................................28
6.1.2.4 9600 bit/s synch/asynch ...........................................................28
6.1.2.5 9600 or 2x4800 bit/s synch/asynch ............................................28
6.1.3 Modulation and channel bandwidth ............................................................29
6.1.4 1+1 switching criteria..............................................................................29
6.1.5 Cable Interface .......................................................................................30
6.1.6 Consumption and max current adsorption ..................................................31
6.1.7 Fuses ....................................................................................................31
6.2 ODU characteristics...........................................................................................32
6.3 EQUIPMENT GENERAL CHARACTERISTICS............................................................32
6.3.1 Dimensions ............................................................................................32
6.3.2 Weight ..................................................................................................32
6.3.3 Environmental condition ..........................................................................33
7 ALPLUS2 IDU DESCRIPTION ....................................................................................34

7.1 CONFIGURATION ..............................................................................................34
7.1.1 ALCplus2 block diagrams ...........................................................................34
7.1.2 Controller ..............................................................................................34
7.1.2.1 Service signals.........................................................................35
7.1.2.2 Firmware ................................................................................35
7.1.2.3 Web Lct ..................................................................................35
7.1.3 LIM .......................................................................................................35
7.1.3.1 Switch for Ethernet ports...........................................................36
7.1.3.2 STM-1 synchronisation ..............................................................38
7.1.4 RIM.......................................................................................................39
7.1.4.1 Modulator................................................................................39
7.1.4.2 Demodulator ...........................................................................39
7.1.4.3 Adaptive code modulation .........................................................39
7.1.4.4 Power supply ...........................................................................41
7.1.4.5 Telemetry IDU/ODU..................................................................41
7.2 LOOPS ............................................................................................................42
7.2.1 Tributary ...............................................................................................42
7.2.2 BaseBand ..............................................................................................42
7.2.3 IDU loop ................................................................................................42
8 ALCPLUS2 IDU DESCRIPTION ..................................................................................46

8.1 CONFIGURATION ..............................................................................................46
8.1.1 Switch for ethernet ports .........................................................................46
2 ALS - ALplus2, ALCplus2 - MN.00224.E - 001

8.1.2 Service channels.....................................................................................46
8.2 ALC BLOCK DIAGRAMS......................................................................................46
9 ODU DESCRIPTION ..................................................................................................49

9.1 ODU VERSIONS................................................................................................49
9.1.1 AS ODU .................................................................................................49
9.1.2 ASN ODU ...............................................................................................49
9.2 DESCRIPTION ..................................................................................................49
9.3 CABLE INTERFACE ............................................................................................50
9.4 POWER SUPPLY ................................................................................................50
9.5 TX SECTION.....................................................................................................50
9.5.1 ATPC operation.......................................................................................51
9.6 RX SECTION ....................................................................................................51
9.7 1+1 Tx SYSTEM...............................................................................................51
Section 3.
INSTALLATION 57
10 INSTALLATION AND PROCEDURES FOR ENSURING THE ELECTROMAGNETIC

COMPATIBILITY.......................................................................................................57
10.1 GENERAL INFORMATION TO BE READ BEFORE THE INSTALLATION..........................57
10.2 GENERAL.........................................................................................................58
10.3 MECHANICAL INSTALLATION..............................................................................58
10.3.1 IDU installation.......................................................................................58
10.3.2 IDU installation.......................................................................................58
10.4 ELECTRICAL WIRING.........................................................................................58
10.5 CONNECTIONS TO THE SUPPLY MAINS ................................................................60
10.6 GROUNDING CONNECTION ................................................................................60
11ALCPLUS2CONNECTORS ............................................................................................61
11.1 IDU FRONT PANEL ............................................................................................61
11.1.1 LIM connectors .......................................................................................61
11.1.2 RIM connectors.......................................................................................61
11.1.3 Controller connectors ..............................................................................61
11.2 IDU BODY CONNECTORS ...................................................................................62
12 ALCPLUS2 CONNECTORS ..........................................................................................69

12.1 IDU FRONT PANEL ............................................................................................69
12.2 ALCplus2 1+0/1+1 (GAI0157/GAI0152) ..............................................................69
12.3 ALCplus2 16E1 1+0/1+1 (GAI0155/GAI0156) ......................................................70
12.4 ALCplus2 NODAL 1+0/1+1 (GAI0163/GAI0162)....................................................70
12.5 ALCplus2 32E1 1+0/1+1 (GAI0169/GAI0168) ......................................................71
13 INSTALLATION ONTO THE POLE OF THE ODU WITH SEPARATED ANTENNA .............72
13.1 INSTALLATION KIT ...........................................................................................72
13.2 REQUIRED TOOLS FOR MOUNTING (NOT SUPPLIED) .............................................73
13.3 INSTALLATION PROCEDURE ...............................................................................73
13.4 GROUNDING ....................................................................................................75

14 INSTALLATION ONTO THE WALL OF THE ODU WITH SEPARATED ANTENNA.............89
14.1 INSTALLATION KIT ...........................................................................................89
14.2 REQUIRED TOOLS FOR MOUNTING (NOT SUPPLIED) .............................................89
14.3 INSTALLATION PROCEDURE ...............................................................................90
14.4 GROUNDING ....................................................................................................92
15 INSTALLATION ONTO THE POLE OF THE ODU WITH INTEGRATED ANTENNA .........103
15.1 FOREWORD ................................................................................................... 103
15.2 INSTALLATION KIT ......................................................................................... 103
15.3 REQUIRED TOOLS FOR MOUNTING (NOT SUPPLIED) ........................................... 104
15.4 INSTALLATION PROCEDURE ............................................................................. 104
15.4.1 Installation onto the pole of the support system and the antenna ................ 104
15.4.2 Installation of ODU................................................................................ 105
15.4.3 ODU installation.................................................................................... 106
15.5 ANTENNA AIMING........................................................................................... 106
15.6 COMPATIBILITY.............................................................................................. 106
15.7 GROUNDING .................................................................................................. 107
16 INSTALLATION ONTO THE POLE OF THE ODU WITH INTEGRATED ANTENNA

(KIT V32307, V32308, V32309) .............................................................................123
16.1 FOREWORD ................................................................................................... 123
16.5 1+0 MOUNTING PROCEDURES ......................................................................... 125
16.5.1 Setting antenna polarization ................................................................... 125
16.5.2 Installation of the centring ring on the antenna ......................................... 125
16.5.3 Installation of 1+0 ODU support ............................................................. 125
16.5.4 Installation onto the pole of the assembled structure ................................. 125
16.5.5 Installation of ODU (on 1+0 support)....................................................... 125
16.5.6 Antenna aiming .................................................................................... 126
16.5.7 ODU grounding..................................................................................... 126
16.6.1 Installation of Hybrid ............................................................................. 126
16.6.2 Installation of ODUs (on hybrid for 1+1 version) ....................................... 127
17 INSTALLATION ONTO THE POLE OF THE ODU WITH RFS INTEGRATED ANTENNA...138
17.1 FOREWORD ................................................................................................... 138
17.5.1 Setting antenna polarization ................................................................... 139
17.5.2 Installation of the centring ring on the antenna ......................................... 140
17.5.3 Installation of 1+0 ODU support ............................................................. 140
17.5.4 Installation onto the pole of the assembled structure ................................. 140
17.5.5 Installation of ODU (on 1+0 support)....................................................... 140
17.5.6 Antenna aiming .................................................................................... 140
17.5.7 ODU grounding..................................................................................... 141
17.6.1 Installation of Hybrid ............................................................................. 141
17.6.2 Installation of ODUs (on hybrid for 1+1 version) ....................................... 141

Section 4.
LINE-UP 153
18 LINE–UP OF THE RADIO HOP .................................................................................153

18.1 LINE–UP OF THE RADIO HOP............................................................................ 153
18.1.1 Equipment configuration ........................................................................ 153
18.1.2 Antenna alignment and received field measurement .................................. 154
18.1.3 Network element configuration ............................................................... 154
18.1.4 Radio checks ........................................................................................ 155
19 BACK UP FULL EQUIPMENT CONFIGURATION WITHOUT POSSIBILITY OF MODIFYING

THE PARAMETERS .................................................................................................156
19.1 SCOPE .......................................................................................................... 156
19.2 CONFIGURATION UPLOAD ............................................................................... 156
19.3 CONFIGURATION DOWNLOAD .......................................................................... 156
20 LINE-UP FOR ETHERNET TRAFFIC ..........................................................................157

20.1 GENERAL....................................................................................................... 157
20.2 LOCAL LAN-1 PORT TO REMOTE LAN-1 PORT TRANSPARENT CONNECTION LAN
PER PORT ...................................................................................................... 157
20.3 FROM 3 PORT TO 3 PORT CONNECTIONS ........................................................... 162
20.4 FROM 3 PORT TO 3 PORT CONNECTIONS ........................................................... 167
21 HOW TO CHANGE ADDRESS ON REMOTE EQUIPMENT WITHOUT LOSING THE

CONNECTION .........................................................................................................172
21.1 TOOLS .......................................................................................................... 172
21.2 PROCEDURE................................................................................................... 172
Section 5.
PROGRAMMING AND SUPERVISION 185
22 PROGRAMMING AND SUPERVISION .......................................................................185

22.1 GENERAL....................................................................................................... 185
22.2 WEBLCT ........................................................................................................ 185
Section 6.
COMPOSITION 189
23 COMPOSITION OF MODULAR IDU...........................................................................189

23.1 GENERAL....................................................................................................... 189
23.2 IDU PART NUMBER ......................................................................................... 189
23.3 COMPOSITION OF THE INDOOR UNIT................................................................ 190
24 COMPOSITION OF OUTDOOR UNIT.........................................................................192

24.1 GENERAL....................................................................................................... 192
Section 7.
LISTS AND SERVICES 213
25 LIST OF FIGURES ...................................................................................................213
26 LIST OF TABLES .....................................................................................................217
27 ASSISTANCE SERVICE............................................................................................219

Section 1.
USER GUIDE
1 DECLARATION OF CONFORMITY
SIAE Microelettronica S.p.A. declares that the products:
- digital radio relay system AS6

complies with the essential requirements of article 3 of the R&TTE Directive (1999/5/EC) and therefore is
marked CE.
The following standards have been applied:
- EN 60950-1: 2006 “Safety of information technology equipment”.

- EN 301 489–4 V.1.3.1 (2002–8): “Electromagnetic compatibility and radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 4. Specific con-
ditions for fixed radio links and ancillary equipment and services”
- ETSI EN 301 751 V.1.1. (2002–12): “Fixed Radio Systems; Point–to point equipment and antennas;
generic harmonized standard for point–to–point digital fixed radio systems and antennas covering the
essential requirements under article 3.2 of the 1999/5/EC Directive”.
7
2 FIRST AID FOR ELECTRICAL SHOCK AND SAFETY
RULES
2.1 FIRST AID FOR ELECTRICAL SHOCK
Do not touch the bare hands until the circuit has been opened. pen the circuit by switching off the line
switches. If that is not possible protect yourself with dry material and free the patient from the con-
ductor.
2.1.1 Artificial respiration
It is important to start mouth respiration at once and to call a doctor immediately. suggested procedure
for mouth to mouth respiration method is described in the Tab.1.
2.1.2 Treatment of burns
This treatment should be used after the patient has regained consciousness. It can also be employed while
artificial respiration is being applied (in this case there should be at least two persons present).
Warning
• Do not attempt to remove clothing from burnt sections
• Apply dry gauze on the burns
• Do not apply ointments or other oily substances.
8
Tab.1 - Artificial respiration
Step Description Figure
Lay the patient on his back with his arms parallel to the body.
If the patient is laying on an inclined plane, make sure that his
1 stomach is slightly lower than his chest. Open the patients
mouth and check that there is no foreign matter in mouth (den-
tures, chewing gum, etc.).
Kneel beside the patient level with his head. Put an hand under
the patient’s head and one under his neck.
Lift the patient’s head and let it recline backwards as far

2 as possible.
Shift the hand from the patient’s neck to his chin and his
mouth, the index along his jawbone, and keep the other fingers
closed together.
3 While performing these operations take a good supply of oxy-

gen by taking deep breaths with your mouth open
With your thumb between the patient’s chin and mouth keep
his lips together and blow into his nasal cavities
While performing these operations observe if the patient’s

chest rises. If not it is possible that his nose is blocked: in that
case open the patient’s mouth as much as possible by pressing
on his chin with your hand, place your lips around his mouth
and blow into his oral cavity. Observe if the patient’s chest
5
heaves. This second method can be used instead of the first
even when the patient’s nose is not obstructed, provided his
nose is kept closed by pressing the nostrils together using the
hand you were holding his head with. The patient’s head must
be kept sloping backwards as much as possible.
Start with ten rapid expirations, hence continue at a rate of

twelve/fifteen expirations per minute. Go on like this until the
6
patient has regained conscious–ness, or until a doctor has as-
certained his death.
2.2 SAFETY RULES
When the equipment units are provided with the plate, shown in Fig.1, it means that they contain compo-
nents electrostatic charge sensitive.
9
Fig.1 - Components electrostatic charge sensitive indication
In order to prevent the units from being damaged while handling, it is advisable to wear an elasticized band
(Fig.2) around the wrist ground connected through coiled cord (Fig.3).
Fig.2 - Elasticized band
Fig.3 - Coiled cord
The units showing the label, shown in Fig.4, include laser diodes and the emitted power can be dangerous
for eyes; avoid exposure in the direction of optical signal emission.
Fig.4 - Laser indication
10
ALS - ALplus2, ALCplus2 - MN.00224.E - 001
2.3 CORRECT DISPOSAL OF THIS PRODUCT (Waste electrical &
electronic equipment)
(Applicable in the European Union and other European countries with separate collection systems). This
marking of Fig.5 shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household users should contact either
the retailer where they purchased this product, or their local government office, for details of where and
how they can take this item for environmentally safe recycling. Business users should contact their supplier
and check the terms and conditions of the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
Fig.5 - WEEE symbol - 2002/96/CE EN50419
2.4 INTERNAL BATTERY
Inside the equipment, in IDU unit, there is a lithium battery.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to law.

11
3 PURPOSE AND STRUCTURE OF THE MANUAL
3.1 PURPOSE OF THE MANUAL
The purpose of this manual consists in providing the user with information which permit to operate and
maintain the ALS radio family.
Warning: This manual does not include information relevant to the SCT/LCT management program win-
dows and relevant application. They will provided by the program itself as help-on line.
3.2 AUDIENCE BASIC KNOWLEDGE
The following knowledge and skills are required to operate the equipment:
• a basic understanding of microwave transmission
• installation and maintenance experience on digital radio system
• a good knowledge of IP/OSI networks and routing policy.
3.3 STRUCTURE OF THE MANUAL
The manual is subdivided into sections each of them developing a specific topic entitling the section.
Each section consists of a set of chapters, enlarging the main subject master.
Section 1 – User Guide
It provides the information about the main safety rules and expounds the purpose and the structure of the
manual.
Section 2 – Description and specifications
It traces the broad line of equipment operation and lists the main technical characteristics of the whole
equipment and units it consists of.
List of abbreviation meaning is also supplied.
Section 3 – Installation
The mechanical installation procedures are herein set down as well as the user electrical connections.
The content of the tool kit (if supplied) is also listed.
12
Section 4 – Line–Up
Line–up procedures are described as well as checks to be carried out for the equipment correct operation.
The list of the instruments to be used and their characteristics are also set down.
Section 5 – Programming and supervision
The ALS radio family is programmed and supervised using different software tools. Some of them are al-
ready available, some other will be available in the future.
This section lists the tools implemented and indicates if descriptions are already available.
Each description of software tools is supplied in a separated manual.
Section 6 – Composition
Position, part numbers of the components the equipment consist of, are shown in this section.
Section 7 – Lists and assistance
This section contains the lists of figures and tables and the assistance service information.

13
14
Section 2.
DESCRIPTIONS AND SPECIFI-
CATION
4 ABBREVIATION LIST
4.1 LIST OF ABBREVIATIONS
- ACM Adaptive Code Modulation
- AF Assured Forwarding
- AL Access Link
- ALS Access LInk Series
- AIS Alarm Indication Signal

- ATPC Automaric Transmit Power Control
- BB Baseband
- BBER Background Block Error Radio
- BER Bit Error Rate
- DSCP Differentiated Service Code Point
- DSP Digital Signal Processing

- E1 2 Mbit/s
- EMC/EMI Electromagnetic Compatibility/Electromagnetic Interference
- EOC Embedded Overhead Channel
- ERC European Radiocommunication Committee
- ESD Electrostatic Discharge
- FEC Forward Error Corrector
- FEM Fast Ethernet Module
- HDLC High Level Data Link Control

15
- IDU Indoor Unit
- IF Intermediate Frequency
- IpToS Type of Service IP
- LAN Local Area Network
- LAPS Link Access Procedure SDH
- LCT Local Craft Terminal
- LIM Line Interface Module
- LLF Link Loss Forwarding
- LOF Loss Of Frame
- LOS Loss Of Signal
- MAC Media Access Control

- MDI Medium Dependent Interface
- MDIX Medium Dependent Interface Crossover
- MIB Management Information Base
- MMIC Monolitic Microwave Integrated Circuit
- MTBF Mean Time Between Failure
- NE Network Element
- ODU Outdoor Unit
- OSI Open System Interconnection
- PDH Plesiochronous Digital Hierarchy
- PPI Plesiochronous Physical Interface
- PPP Point to Point Protocol
- PTOS Priority Type Of Service
- RIM Radio Interface Module
- SCT Subnetwork Craft Terminal
- SNMP Simple Network Management Protocol

- TCP/IP Transmission Control Protocol/Internet Protocol
- TOS Type Of Service
- VID Virtual LAN Identifier
- VLAN Virtual LAN
- WFQ Wait Fair Queue
- Wayside Traffic Additional 2 Mbit/s Traffic
16
5 SYSTEM PRESENTATION
5.1 RECOMMENDATION
The equipment complies with the following international standards:
• EN 301 489–4 for EMC
• EN 302 217 for all frequency bands
• ITU–R recommendations for all frequency bands
• EN 300 132–2 characteristics for power supply

• EN 300 019 environmental characteristics (Operation class 3.2 for IDU and class 4.1 for ODU; stor-
age: class 1.2; transport: class 2.3)
• EN 60950 for safety.
5.2 SYSTEM ARCHITECTURE
The ALplus2 radio link is a split mount equipment made up of:
• an indoor unit called IDU for 19” rack mounting that interfaces tributaries and supervises the full
equipment
• an outdoor unit called ODU for pole or wall mounting with RF circuitry and antenna flange.
IDU units are available in the following mechanical versions

• modular: ALCplus2. Main circuits are divided in modules, replaceable in case of failure
• compact: ALCplus2. All the circuitry is housed in a single board.
ODU units are available in the following versions:
• AS (max capacity of 341 Mbit/s)
• ASN (max capacity of 341 Mbit/s)
5.3 ALCplus2 modular IDU
The unit is available in the following configurations:
• ALCplus2 1+0 for E1 and Ethernet traffic (see Fig.6)
• ALCplus2 1+1 for E1 and Ethernet traffic (see Fig.7)
The following modules make up the modular IDU.
17
5.3.1 LIM
The LIM interfaces the in (out) E1 streams and Ethernet traffic and, through a multiplexing (demultiplex-
ing) and bit insertion (bit extraction) process, supplies (receives) the aggregate signal to the modulator
(from the demodulator). In addition the LIM performs the digital processing of the QAM modulator.
Moreover the module duplicates the main signals at the Tx side and performs the changeover at the Rx
side in the 1+1 version.
5.3.2 RIM
The RIM contains:
• the IF section of the programmable modemodulator (8 available profiles: 4QAM, 4QAM strong,
8PSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM)
• the power supply unit that processes the battery voltage to supply power to the IDU circuits and
send the battery voltage towards the ODU
• the cable interface for the bidirectional communication between IDU and ODU via interconnecting
cable
• thanks to ACM (Adaptive Code Modulation) actual modulation can be automatically changed accord-
ing to available S/N.
5.3.3 Controller
The Controller performs the following operations:
• interfaces the service signals as 1x9600 bit/s or 2x4800 bit/s, 64 kbit/s, 2 Mbit/s (details are given
in the system technical specification)
• contains the equipment software that permits to control and to manage all the equipment function-
ality through a main controller and associated peripherals distributed within IDU and ODU
• interfaces the SCT/LCT management system through Ethernet, RS232 and USB ports
• receive external alarms and route them to relay contact along with the internal alarms generated
by the equipment.
5.4 ALCplus2 compact IDU
The unit is available in the following configurations:
• ALCplus2 1+0 see Fig.8
• ALCplus2 1+1 see Fig.9
• ALCplus2 1+0 exp 16E1 see Fig.10

• ALCplus2 1+0 exp nodal see Fig.14
• ALCplus2 1+1 exp nodal see Fig.15
The compact IDU are made by a single board.
18
The line interfaces contain the tributary connectors and, by means of processes of multiplexing/demulti-
plexing and of bit insertion/extraction, provide/receive the aggregate signal to/from the modulator/de-
modulator.
The line interfaces realize the digital processing for the QAM modulator and, in 1+1 configuration, duplicate
the main signals on the transmission side and execute the switch on the reception side.
The interfaces to the ODU contain the interface of the cable for the bidirectional communication between
ODU and IDU, and implement the IF section of the mo-demodulator. The power supply units of the IDU
process the battery voltage and supply power to the circuits of IDU and ODU. The controller section of the
radio contains the interfaces of the service channels, stores the firmware of the IDU, interfaces the SIAE
management systems through dedicated supervision ports and forwards external and internal alarms to
the relay contacts.
5.5 ODU
The ODU unit contains circuits that permits to interface from one side the IDU and the antenna from the
other side.
The QAM modulated carrier is shifted to RF frequency bands through a double conversion.
Similarly it occurs at the receive side to send the IF converted carrier to the demodulator within the IDU.
The ODU unit is available in two different versions: AS and ASN (optimized).
The ODU AS is also called “Universal” because it can be used as SDH ODU connected to SIAE ALS SDH IDU
(SIAE SDH link family).
Antenna coupling is performed through a balanced or unbalanced hybrid system.
5.6 Management
ALplus2 equipment can be locally and remotely controlled via an internal dedicated application software
called WEBLCT through Internet Browser and LAN connection. A serial/USB connection can be used through
the Web Lct console, an application that can be downloaded from SIAE site (http://www.siaemic.com)
It provides a friendly graphic interface complying with current standard use of keyboard, mouse, windows
and so on.
Other software available for management of a network of ALplus2 is SCT (Windows) and NMS5UX/NMS5LX
(Unix/Linux).
5.6.1 Hardware platform
The hardware platform used by SCT/LCT is based on personal computer having at least following charac-
teristics:
• microprocessor Pentium 4 or similar
• 1GB RAM
• windows compatible graphic monitor
• HD with 200 Mbyte of free space
• Windows 95/Windows NT/Windows 98/Windows 2000/Windows XP/Window Vista
• LAN o USB connection

19
5.6.2 Management ports
The SCT/LCT program is connected to the equipment via the following communication ports:
• MNGT/1 or MNGT/2 (Ethernet LAN 10BaseT)
• RS232 (asynchronous serial line)
• LCT (USB)
• Embedded Overhead Channel (EOC) embedded into the radio frame
• Embedded Overhead Channel (EOC) embedded into a 16 kbit/s or 4x16 kbit/s time slot of one of
the 2 Mbit/s tributary signals.
5.6.2.1 Q3/1 and Q3/2
• LAN cable type 802.3 10BaseT
• Connector RJ45
• Connection to LAN direct with a CAT5 Twisted Pair
• Protocol TCP/IP or IPoverOSI
5.6.2.2 RS232
• Electrical interface V.28
• Connector SUB-D 9pin
• Asynchronous baud rate 9600,19200,38400,57600
• Protocol PPP
5.6.2.3 LCT USB
• Electrical interface USB 1.1 version
• Baud rate 1.5 Mbit/s
• Protocol PPP
5.6.3 Protocols
SNMP along with IP or OSI protocol stacks are used to reach and manage the equipment operation.
1 2 3 ON 48V
SPEED
PoE
ACT FAIL
LINK
+
10-100-1000 BaseT/100-1000 BaseX 1 STM1 2 Trib: 1-8 Trib: 9-16

-
LINK LINKNURG URG
ACT ACT WAY
SIDE
SW TEST
LCT RS232 USER IN/OUT MNGT/1 MNGT/2 CH1 CH2 2Mb/s
Fig.6 - ALCplus2 1+0
20
1 2 3 ON 48V
SPEED
PoE
ACT FAIL
LINK
+
-
LINK LINK NURG URG 48V
ACT ACT WAY
SIDE
+
SW TEST
-
YELLOW SPEED LAN 2 LAN 4 Trib. B
2
M 3.15A
250VAC 48VDC
MNGT LAN 3 LAN 4 NURG URG
1 LCT
SW
+
GREEN LINK LAN 1 LAN 3 Trib. A SD USER IN/OUT TEST ON -
YELLOW SPEED LAN 2 LAN 4 Trib. B
2 2
M 3.15A
250VAC
MNGT 48VDC
LAN 3 LAN 4 NURG URG
1 LCT 1 2 1
SW
+
YELLOW SPEED LAN 2 LAN 4 Trib. B Trib. 1-8 Trib. 9-16
2
M 3.15A
250VAC 48VDC
1 LCT
SW
+
Fig.10 - ALCplus2 1+0 exp 16E1
YELLOW SPEED LAN 2 LAN 4 Trib. B Trib. 1-8 Trib. 9-16
2 2
M 3.15A
250VAC
MNGT 48VDC
1 LCT 1 2 1
SW
GREEN LINK LAN 1 LAN 3 Trib. A SD USER IN/OUT TEST ON + -
Fig.11 - ALCplus2 1+1 exp 16E1
YELLOW SPEED LAN 2 LAN 4 STM1 Trib. B Trib. 1-8 Trib. 9-16 Trib. 17-24 Trib. 25-32
1 2
2
ON M 3.15A 48V
MNGT LAN 3 LAN 4 250V
NURG URG
1 LCT
SW
-
+
GREEN LINK LAN 1 LAN 3 Trib. A SD USER IN/OUT TEST ON
Fig.12 - ALCplus2 1+0 32E1
YELLOW SPEED LAN 2 LAN 4 STM1 Trib. B Trib. 1-8 Trib. 9-16 Trib. 17-24 Trib. 25-32
1 2 2
2
ON M 3.15A
MNGT 48V
LAN 3 LAN 4 NURG URG 250V
1 LCT 1 2 1
SW
-
+
GREEN LINK LAN 1 LAN 3 Trib. A SD USER IN/OUT TEST ON
Fig.13 - ALCplus2 1+1 32E1
YELLOW SPEED LAN 2 LAN 4 STM1 Trib. B Trib. 1-8 Trib. 9-16
1 2 1 2
2
M 3.15A
ON NBUS 250VAC 48VDC
1 LCT
SW
+
Fig.14 - ALCplus2 1+0 exp nodal

21
YELLOW SPEED LAN 2 LAN 4 STM1 Trib. B Trib. 1-8 Trib. 9-16
1 2 1 2
2 2
M 3.15A
ON 250VAC
MNGT NBUS 48VDC
1 LCT 1 2 1
SW
+
Fig.15 - ALCplus2 1+1 exp nodal
22
6 TECHNICAL SPECIFICATIONS
6.1 IDU CHARACTERISTISC
In the following paragraphs are listed only the main characteristics of an IDU typology.
Further information are included in the chapter relevant that IDU.
6.1.1 Traffic interfaces
• ALCplus2, max transmitted capacity 341 Mbit/s:
- 16E1 G.703 75/120 Ohm (2SCSI connector, 8E1 each)
- 2 STM1 (SFP connector)
- 3 Ethernet ports: 2 RJ45, electrical (LAN1 and LAN2) and 2 SFP, optical (LAN1 and LAN3). LAN1
can be set electrical or optical.
• ALCplus2, max transmitted capacity 341 Mbit/s. Traffic options can vary depending on IDU version:
- 16E1 G.703 75/120 Ohm (2SCSI connectors, 8E1 each)
- 32E1 G.703 75/120 Ohm (4SCSI connectors, 8E1 each)
- 2 STM1 (SFP connector)

- 4 Ethernet ports: 4 RJ45, electrical (LAN1, LAN2, LAN3 and LAN4) and 2 SFP, optical (LAN3 and
LAN4). LAN3 and LAN4 can be set electrical or optical
- 2 BUS for traffic connections with other ALCplus2 IDUs (same version).
6.1.1.1 2 Mbit/s (E1 G.703)
Input side
• Bit rate 2048 kbit/s ±50 ppm
• Line code HDB3
• Rated impedance 75 Ohm or 120 Ohm
• Rated level 2.37 Vp/75 Ohm or 3 Vp/120 Ohm
• Return loss 12 dB from 57 kHz to 102 kHz

18 dB from 102 kHz to 2048 kHz
• Max attenuation of the input cable 6 dB according to f trend
• Accepted jitter see Tab. 2, CCITT Rec. G.823
• Transfer function see Fig. 1, CCITT Rec. G.742
• Connector type SCSI 50 pin

23
Output side
• Output jitter according to G.742/G.823
• Pulse shape see Fig. 15, CCITT Rec. G.703

• Connector type SCSI 50 pin
6.1.1.2 STM1 electrical
Input side
• Bit rate 155520 kbit/s ±4.6 ppm
• Line code CMI
• Rated impedance 75 Ohm
• Rated level 1 Vpp ±0.1V
• Return loss ≥ 15 dB from 8 MHz to 240 MHz

• Max attenuation of the input cable 12.7 dB at 78 MHz ( f trend)
Output side
• Bit rate 155520 kbit/s ±4.6 ppm
• Rated level 1 Vpp ±0.1 V
• Pulse shape see Fig. 24 and Fig. 25 of ITU-T Rec. G.703
6.1.1.3 STM1 optical
The STM1 interface can be specialised for different applications, by simply equipping the STM1 interface
with the appropriate pluggable optical or electrical transceiver. Optical interface has LC connectors. Electric
interface has 1.0/2.3 connectors. Information about the presence/absence and type of transceiver to the
main controller. The characteristics of all the possible optical interfaces are summarised in Tab.2.
Tab.2 - Optical interface characteristics
Launched Minimum
Operating Distance
Interface Ref. power sensitivity Transceiver Fibre
wavelength (km)
(dBm) (dBm)
L-1.2 G.957 0 ... -5 -34 1480 - 1580 Laser Single-Mode Up to 80
L-1.1 G.957 0 ... -5 -34 1263 - 1360 Laser Single-Mode Up to 40
S-1.1 G.957 -8 ... -15 -28 1263 - 1360 Laser Single-Mode Up to 15
I-1 ANSI -14 ... -20 -28 1263 - 1360 Laser MultiMode Up to 2
The LIM is provided with Automatic Laser Shutdown as prescribed by ITU-T G.664 Recommendation.
24
6.1.1.4 Ethernet interface
- Ethernet connectors IEEE 802.3 10/100/1000 BaseT RJ45

IEEE 802.3 100/1000 BaseX LC
- Ethernet switch functionality MAC Switching

MAC Learning
MAC Ageing
IEEE 802.1q VLAN
IEEE 802.3x Flow Control
IEEE 802.1p QoS
IP-V4 ToS/DSCP
IP-V6 TC/DSCP
IEEE 802.1D STP
IEEE 802.1W RSTP
- Ethernet latency ≤ 2609 μs for standard frame sizes

≤ 11684 μs for Jumbo frame sizes
- Guaranteed Ethernet Throughput (Mbit/s) see Tab.3
Tab.3 - Guaranteed Ethernet Throughput (Mbit/s) for ALCplus2/ALCplus2 (Ethernet only)
Frame Size (byte)

Bandwidth Modulation
64 128 256 512 1024 1518
4QAMs 10.1 9.4 9.1 8.9 8.7 8.7
4QAM 12.5 11.6 11.2 11.0 10.8 10.7
8PSK 17.1 16.0 15.4 15.1 14.8 14.7
16QAM 24.3 22.7 21.8 21.4 21.0 20.9

7 MHz
32QAM 29.3 27.4 26.4 25.8 25.4 25.2
64QAM 36.3 33.8 32.6 31.9 31.3 31.2
128QAM 40.7 38.0 36.6 35.8 35.2 35.0
256QAM 47.9 44.7 43.0 42.2 41.4 41.2
4QAMs 20.3 18.9 18.2 17.8 17.5 17.4
4QAM 24.2 22.6 21.7 21.3 20.9 20.8
8PSK 33.7 31.4 30.3 29.6 29.1 29.0
16QAM 47.6 44.5 42.8 41.9 41.2 41.0

14 MHz
32QAM 59.7 55.8 53.7 52.6 51.6 51.4
64QAM 71.5 66.7 64.2 62.9 61.8 61.5
128QAM 83.1 77.6 74.7 73.2 71.9 71.5
256QAM 97.7 91.2 87.7 85.9 84.4 84.0
4QAMs 41.5 38.6 37.2 36.4 35.8 35.6
4QAM 48.7 45.3 43.6 42.7 41.9 41.7
8PSK 72.8 67.7 65.2 63.9 62.7 62.4
16QAM 96.7 90.0 86.6 84.8 83.4 82.9

28 MHz
32QAM 121.1 112.7 108.5 106.2 104.4 103.8
64QAM 145.0 135.0 129.9 127.3 125.0 124.4
128QAM 168.7 157.0 151.1 148.0 145.4 144.7
256QAM 198.1 184.4 177.5 173.9 170.8 169.9

25
4QAMs 82.3 76.6 73.6 72.1 71.2 70.9
4QAM 95.7 89.1 85.6 83.8 82.8 82.5
8PSK 142.9 133.0 127.7 125.0 123.5 123.1
16QAM 192.9 179.0 171.9 168.3 166.1 165.5

56 MHz
32QAM 235.3 218.4 209.8 205.3 202.7 201.9
64QAM 280.0 259.8 249.6 244.3 241.1 240.2
128QAM 333.3 309.6 297.4 291.0 288.2 287.2
256QAM 396.2 369.9 355.3 347.7 343.2 341.9
- Guaranteed ethernet latency (ms) see Tab.4
for ALCplus2 (Ethernet only)
Frame Size (byte)

Bandwidth Modulation
64 128 256 512 1024 1518 10000
4QAMs 1.042 1.111 1.248 1.522 2.09 2.609 11.684
4QAM 0.844 0.900 1.011 1.233 1.693 2.113 9.465
8PSK 0.627 0.668 0.750 0.913 1.229 1.541 6.974
16QAM 0.477 0.505 0.560 0.67 0.895 1.115 4.755

7 MHz
32QAM 0.401 0.426 0.475 0.573 0.756 0.938 4.214
64QAM 0.477 0.496 0.533 0.607 0.768 0.908 3.35
128QAM 0.52 0.537 0.572 0.642 0.774 0.914 3.222
256QAM 0.507 0.521 0.550 0.608 0.726 0.845 2.761
4QAMs 0.954 0.987 1.053 1.186 1.462 1.715 6.104
4QAM 0.8 0.828 0.884 0.995 1.226 1.439 5.12
8PSK 0.575 0.596 0.637 0.719 0.882 1.044 3.557
16QAM 0.418 0.432 0.461 0.518 0.639 0.757 2.634

14 MHz
32QAM 0.345 0.357 0.381 0.428 0.518 0.618 2.176
64QAM 0.439 0.449 0.469 0.51 0.59 0.669 2.02
128QAM 0.458 0.467 0.486 0.523 0.594 0.663 1.907
256QAM 0.444 0.452 0.468 0.499 0.557 0.623 1.656
4QAMs 0.475 0.492 0.526 0.595 0.735 0.867 3.136
4QAM 0.406 0.421 0.450 0.508 0.628 0.74 2.677
8PSK 0.274 0.284 0.305 0.347 0.426 0.508 1.881
16QAM 0.214 0.222 0.238 0.271 0.334 0.395 1.483

28 MHz
32QAM 0.176 0.183 0.197 0.224 0.276 0.326 1.235
64QAM 0.227 0.232 0.243 0.265 0.311 0.356 1.067
128QAM 0.237 0.242 0.252 0.272 0.312 0.351 1.003
256QAM 0.231 0.236 0.246 0.265 0.298 0.333 0.982
26
4QAMs 0.241 0.250 0.268 0.304 0.377 0.447 1.651
4QAM 0.207 0.215 0.230 0.261 0.324 0.384 1.418
8PSK 0.14 0.146 0.158 0.181 0.226 0.27 1.052
16QAM 0.112 0.117 0.126 0.144 0.179 0.214 0.83

56 MHz
32QAM 0.094 0.098 0.106 0.122 0.154 0.185 0.697
64QAM 0.125 0.129 0.137 0.152 0.178 0.205 0.71
128QAM 0.126 0.129 0.135 0.147 0.172 0.196 0.601
256QAM 0.121 0.124 0.129 0.14 0.162 0.183 0.549
6.1.2 Service channels
ALplus2 only.
Three service channels available subdivided as follows:

• V28 data channel, via software can be set as:
- one channel V.28 async. 9600 kbit/s
- two channels (in the same connector) V.28 async. 4800 kbit/s
- one channel V.28 async. 9600 kbit/s with DTR and DSR
- one channel V.28 sync. 9600 kbit/s with DTR, DSR and DCD locally terminated
• V11 64 kbit/s co/contradirectional

• E1 wayside for capacities greater or equal to 16x2 Mbit/s
6.1.2.1 2 Mbit/s (E1 G.703) wayside
Input side
• Line code HDB3
• Return loss 12 dB from 57 kHz to 102 KHz

• Max attenuation of the input cable 6 dB according to f trend
• Accepted jitter see Tab. 2, CCITT Rec. G.823
• Transfer function see Fig. 1, CCITT Rec. G.742

• Connector type RJ45 (in/out in the same conn.)
Output side

27
• Output jitter according to G.742/G.823
• Pulse shape see Fig. 15, CCITT Rec. G.703
• Connector type RJ45 (in/out in the same conn.)
6.1.2.2 64 kbit/s codirectional
• Tolerance ± 100 ppm
• Coding synch + data + octet as per G.703
• Impedance 120 Ohm
• Max attenuation of the input cable 3 dB at 128 kHz
• User side CCITT Rec. G.703
• Input/output level 1 Vp/120 Ohm ±0.1 V
• Return loss see par. 1.2.1.3 in CCITT Rec. G.703
• Connector RJ45
6.1.2.3 64 kbit/s contradirectional
• Tolerance ± 100 ppm

• Coding clock and data on separate wires
• Impedance 120 Ohm
• Max attenuation of the input cable 3 dB at 128 kHz

• Equipment side contradirectional
• Input/output level 1 Vp/120 Ohm ±0.1 V
• Electrical interface CCITT Rec. V.11

• Connector RJ45
6.1.2.4 9600 bit/s synch/asynch
• Data interface RS232
• Input speed 9600 baud

• Control wires DTR, DSR, DCD
• Connector RJ45
6.1.2.5 9600 or 2x4800 bit/s synch/asynch
• Input speed 4800 or 9600 bit/s

• Connector RJ45
28
6.1.3 Modulation and channel bandwidth
• Carrier IF mo-demodulating frequency Tx side 330 MHz

Rx side 140 MHz
• Type of modulation 4QAM strong, 4QAM, 8PSK, 16QAM, 32QAM,

64QAM, 128QAM, 256 QAM
• Bandwidth 7MHz, 14MHz, 28MHz, 56MHz
• Modulation approach ACM
• Modulating signal depending on selected capacities

• Equalization 5 taps
• Coding gain 2.5 dB at 10-6 1 dB at 10-3
• Correction LDPC
6.1.4 1+1 switching criteria
Rx switch
Rx switch is hitless and the system has built in capabilities of minimizing errors during the detection time.
Branch 1 is preferential and the system switches to branch 2 only when branch 1 is error affected. The
switching facility provides automatic synchronization of the two incoming streams up to:
• dynamic difference ±100 bytes
• static delays ± 100 bytes.

Tab.5 shows Rx Alarm Priority.
Tab.5 - Rx Alarm Priority
Priority Levels Definition
Highest Priority 1 RIM PSU Alarm
l Manual forcing (selectable by software)

l
l CRC pulse from demodulator
l Priority 2
V Branch Rx alarms
Lowest Revertive Rx (preferential branch selectable by software)
Changeover time for Rx switching (including detection time due to counting of BER 10-6) is ≤ 1 ms.
Tx switch (1+1 hot stand-by)
Tx switch is not hitless. Maximum outage due to the Tx switching (sum of the maximum automatic change-
over + Rx IDU resynchronisation time), with ACM (Adaptive Code and Modulation) activated, is shown in
Tab.6.

29
Tab.6 - Maximum outage due to the Tx switching
Bandwidth Maximum outage due to the Tx switching (msec)
7 MHz < 1500
14 MHz < 1200
28 MHz < 900
56 MHz < 400
Tab.7 shows Tx Alarm Priority.
Tab.7 - Tx Alarm Priority
Priority Levels Definition
Highest Priority 1 RIM PSU Alarm
Priority 2 Manual forcing (selectable by software)
Priority 3 Cable Short Alarm
Priority 3 Cable Open Alarm
Priority 3 Modulator Failure
Priority 3 ODU Unit Failure Alarm
Priority 3 VCO Failure Alarm
Priority 3 IF Unit Alarm
Priority 3 Tx Power Low Alarm
Priority 4 Request from Remote Terminal (both Receivers Alarmed)
Lowest Priority 5 Revertive Rx (preferential branch selectable by software)
The maximum automatic changeover time (including sensing time) for transmitter switching is ≤ 200 ms.
6.1.5 Cable Interface
• Interconnection with ODU unit single coaxial cable for both Tx and Rx
• Cable length 300 m
• Cable rated impedance 50 Ohm
• Signal running along the cable
- Tx nominal frequency 330 MHz
- Rx nominal frequency 140 MHz

- Telemetry IDU -> ODU 17.5 MHz
- Telemetry ODU <- IDU 5.5 MHz
• Transceiver management signals 388 kbit/s bidirectional
• Remote power supply direct from battery voltage.
30
6.1.6 Consumption and max current adsorption
In this paragraphs are listed the following three characteristics: the max current (IMAX) at the power con-
nector of the IDU alone, the max current (IMAX) at the power connector of the IDU with the complete equip-
ment (IDU 1+1 and relevant 2 ODUs) and the consumption of the IDU alone. The consumption of the
complete equipment is described inside the ODU attachment (one for each frequency) with high precision,
at this point we have considered the ODU with the higher consumption (about 25W) among all the avail-
able.
Indicated voltage is related to max current and max consumption.

N.B. The consumption of the complete equipment is described inside the ODU attachment (one for each
frequency).
• ALplus2 IMAX and consumption see Tab.8
• ALCplus2 IMAX and consumption see Tab.8
The power supply connectors of ALplus2 are independent.
The power supply connectors of ALCplus2 are in parallel (through diode).
Tab.8 - IMAX and consumption
Consumption
IDU IMAX (IDU only) IMAX (IDU+ODUs)
(IDU only)
ALplus2 1+0 1A (@40.8 Vdc) 1.7A (@40.8 Vdc) 40W (@57.6 Vdc)
ALplus2 1+1 1.2A (@40.8 Vdc) 1.7A (@40.8 Vdc) 48W (@57.6 Vdc)
ALCplus2 1+0 0.81A (@40.8 Vdc) 1.42A (@40.8 Vdc) 33W (@57.6 Vdc)
ALCplus2 1+1 0.92A (@40.8 Vdc) 2.15A (@40.8 Vdc) 38W (@57.6 Vdc)
ALCplus2 1+0
0.88A (@40.8 Vdc) 1.5A (@40.8 Vdc) 36W (@57.6 Vdc)
exp 16E1
ALCplus2 1+0
0.91A (@40.8 Vdc) 1.52A (@40.8 Vdc) 37W (@57.6 Vdc)
exp nodal
ALCplus2 1+1
1.1A (@40.8 Vdc) 2.23A (@40.8 Vdc) 41W (@57.6 Vdc)
exp 16E1
ALCplus2 1+1
0.91A (@40.8 Vdc) 2.33A (@40.8 Vdc) 45W (@57.6 Vdc)
exp nodal
6.1.7 Fuses
Power supply circuits are protected against overcurrent with fuses on supply line:
• ALplus2 there is an internal soldering fuse on the RIM PCB behind front panel
- Nominal current 3A
- Nominal voltage 125 Vac/dc
- Type timed
- Dimensions 6.10 mm x x2.59 mm
• ALCplus2 accessible on the front panel
- Nominal current 3.15A
- Nominal voltage 250 Vac/dc
- Type medium timed
- Dimensions 5 mm x x20 mm

31
6.2 ODU characteristics
• Frequency range see attachment relevant to ODU frequency
• RF channelling see attachment relevant to ODU frequency
• Go-return frequency see attachment relevant to ODU frequency

• Frequency stability see attachment relevant to ODU frequency
• Spurious transmission see attachment relevant to ODU frequency
• Output power see attachment relevant to ODU frequency
• BER Rx threshold see attachment relevant to ODU frequency
• Max RF level in Rx for BER 10-3 see attachment relevant to ODU frequency
• Additional Tx and Rx losses for 1+1 version see attachment relevant to ODU frequency
• Antenna configuration see attachment relevant to ODU frequency
• Consumption see attachment relevant to ODU frequency
6.3 EQUIPMENT GENERAL CHARACTERISTICS
6.3.1 Dimensions
The dimensions of the unit are the following:

• IDU ALplus2 (1+0/1+1) 480mm x 45mm x 270mm (wxhxd)
• IDU ALCplus2 (1+0/1+1, all versions) 480mm x 45mm x 213mm (wxhxd)
• ODU 1+0 ASN ODU version 254mm x 254mm x 114mm (wxhxd)

• ODU 1+0 AS ODU version 254mm x 254mm x 154mm (wxhxd)
• ODU 1+1 ASN ODU version 278mm x 254mm x 296mm (wxhxd)
• ODU 1+1 AS ODU version 358mm x 254mm x 296mm (wxhxd)
6.3.2 Weight
The weight of the units is the following:
• IDU ALplus2 (1+0/1+1) 3.5 kg
• IDU ALCplus2 (1+0/1+1, all versions) 2.5 kg

• ODU AS (1+0) 5.5 kg
• ODU AS (1+1, with branching unit) 15.5 kg
32
6.3.3 Environmental condition
• IDU operating temperature -5° C to +45° C
• ODU operating temperature -33° C to +45° C
• IDU survival temperature -10° C to +55° C
• ODU survival temperature -40° C to +60° C

• ODU operating humidity 95% at 35° C
• ODU operating condition according to IP65
• ODU dissipation thermal resistance 0.5° C/W
• ODU solar heat gain < 5° C
• Wind speed (ODU with integrated antenna) < 200 km/h
• Storage condition according to T.1.2 ETSI EN 300 019-1-1 (weather

protected, not temperature controlled storage
locations)

33
7 ALPLUS2 IDU DESCRIPTION
7.1 CONFIGURATION
The IDU of the ALplus2 is available in 1+0 and 1+1 configuration.
The IDU is made up by the following modules:
• Controller
• LIM
• RIM (one module in 1+0 configuration, two modules in 1+1 configuration).
7.1.1 ALplus2 block diagrams
In Fig.18 you can find the block diagram of ALplus2 with 16E1, version 1+0 and 1+1 configuration. In
Fig.19 you can find the block diagram of Alplus2 with 16E1, 2x(1+0) configuration.
7.1.2 Controller
The module performs the following operations:

• communication management: it makes use of SNMP as management protocol and IP or IPoverOSI
as communication protocol stacks. The interface ports for the equipment management are the fol-
lowing:
- 2 LAN Ethernet 10BaseT (MNGT/1 and MNGT/2, both RJ45)
- USB port
- RS232 asynchronous used for SCT/NMS connection (using PPP protocol and baud rate speed up
to 57600)
- RS232 asynchronous used for connecting further NEs (using PPP protocol and baud rate speed
up to 57600)
- EOC embedded within the PDH radio frame for connection to the remote NEs
- EOC into a 16kbit/s or 64kbit/s of an E1 timeslot.
• WEB LCT interface can be used woth EOC capacity equal or bigger than 64 kbit/s
• max 2 WEB LCT users can access the same controller
• log-in: the main controller manages the equipment or network login/logout by setting and then con-
trolling the user ID and relevant password
• database (MIB): equipment configuration is stored in a non-volatile memory
• equipment configuration: the equipment is configured through stored configuration parameters or

user commands
• alarm monitoring: acquisition, filtering and correlation of the alarms gathered logger and alarm
sending to the connected managers: SCT/LCT - NMS5UX. Management of the alarm LEDs on the
LIM front panel.
34
• user in and alarm out management: it receives external alarms and route them to relay contacts
along with the internal alarms generated by the equipment
• performance monitoring: PM management as per Recc. G.828
• download: firmware, Web Lct and configuration file can be downloaded. Download activity is based
on FTP protocol.
lLithium battery inside, refer to national rules for disposal.
7.1.2.1 Service signals
The controller offers an electrical interface to the following three service channel:
• 9600 baud/V.28 or 2x4800 baud/V.28 or 9600 baud V.28/RS232 synch/asynch channels
• 64 kbit/s/V.11 codirectional or contradirectional

• E1 wayside G.703.
Service signals connected to the controller modules are sent to the LIM module for MUX/DEMUX process-
ing.
7.1.2.2 Firmware
Equipment software permits to control and manage all the equipment functionality and it is distributed on
two hardware levels: main controller and ODU peripheral controllers.
Firmware can be updated through the Web Lct and it is stored in two different memory banks: one con-
taining the running firmware and the other the stand-by firmware. This permits to download a new
firmware release to the stand by bank without cutting the traffic
Bank switch enables the new release to be used.
7.1.2.3 Web Lct
The Web Lct allows the configuration and the management of the local equipment.
When the remote one is configured properly, the whole radio link can be managed.
Web Lct runs on Internet Explorer and Firefox with Flash player plugin.
WLC is a utility to connect to ALplus2 with USB cable.
WLC and Flash player plugin for IE and Firefox can be downloaded from the site www.siaemic.com after
registration.
7.1.3 LIM
The LIM performs the following operations:
• multiplexing and demultiplexing (MUX/DEMUX process) of traffic (tributaries and Ethernet frames)
• aggregation of the multiplexed signals along with services through a Bit Insertion circuit and vice-
versa. The aggregate frame contains:
- the main signal from the MUX(s)

- the framed service signal from the service MUX
- the EOC signals for supervision message propagation towards the remote equipment
- the frame alignment word (FAW)

35
- the bits dedicated to the FEC
• switch functionality for Ethernet ports
• processing of the signals during the mo-demodulation
• STM1 signal processing and RSOH management
• duplication of the digital processed signals to supply two RIMs in 1+1 configuration.
From the two RIMs the LIM receives I and Q analogue signals then digital converted for the following
processing:
• clock recovery
• frequency and phase carrier locking
• baseband equalisation and filtering
• bit polarity decision

• differential decoding
• parallel to serial conversion to recover the aggregate signal at the receive side.
The aggregate signal is then sent to a frame alignment circuit and CRC analysis and then to the error cor-
rector.
The errors uncorrected by the FEC are properly counted to achieve:
• BER estimate measurement
• radio performances.
7.1.3.1 Switch for Ethernet ports
Inside LIM is present an Ethernet switch with 3 external ports (electrical 1000BaseT or optical 1000BaseX)
and one internal. Only port 1 is present with both kind of interface, the port 2 is electrical and port 3 optical.
The external interfaces (3 operational on 4 presents) are placed on the front panel. Internal port is repre-
sented by the local radio stream where through native Ethernet transport is connected with the remote
equipment.
Ethernet port LEDs
There are 2 LEDs:
• Speed
- one blinking = 10BaseT
- Two blinking = 100BaseT
- Three blinking = 1000BaseT
• LINK/ACT
- on = link up, no activity
- off = link down
- blinking = activity.
Switch function
LIM can operate like a switch between two or more separated LANs with the following advantages:
• to connect two separate LANs more distant than the limits of 2.5 km
• to connect two LANs via radio within a complex digital network
• to keep separated the traffic into two LANs towards MAC filtering to get a total traffic greater than
the traffic in a single LAN.
36
The switch realised into LIM/Ethernet module is transparent (IEEE 802.1d and 802.q) into the same Vlan
described by VLAN Configuration Table.
It works at data link level, Layer 2 of OSI pile, and leave untouched Layer 3 and it takes care to send traffic
from a local LAN to another one (Local and Remote).
Routing is only on the basic of Level 2 addresses, sublevel MAC.
The operation is the following: when a LAN port receives a MAC frame, on the basis of destination address,
it decides which LAN to send it:
• if destination address is on originating LAN the frame is discarded
• if destination address is a known address (towards address learning procedure) and is present into
local address table, the frame is sent only on destination LAN (MAC switching)
• otherwise the frame is sent to all ports with the same VLAN ID (flooding).
Ethernet Full Duplex function
Full duplex mode can be activated into 10/100BaseT interfaces manually or with autonegotiation.
100BaseFx operates always into full duplex mode.
Link Loss Forwarding
Link Loss Forwarding (LLF) is an alarm status of Ethernet interface. LLF can be enabled or disabled.
If LLF is enabled, an US (Un-serviceable) radio alarm condition will generate the alarm status of Ethernet
interface blocking any transmission to it. LLF can be enabled for each ports at front panel.
With LLF enabled the equipment connected (routers, switches so on) can be notified that radio link is not
available and can temporarily re-route the traffic.
MDI/MDIX cross-over
The Ethernet electrical interface into FEM module can be defined by WebLct as MDI or MDIX to cross-over
between pairs so that external cross-over cable is not required.
VLAN functionality
LIM Ethernet module works with IEEE 802.1q and 802.1p tag.
Tag is made up with:
• a fixed word of 2 bytes
• 3 bits for priority according with 802.1p
• 1 fixed bit
• 12 bits VLAN identifier (VLAN ID) according with 802.1q.
Switch cross-connections are based on Vlan Configuration Table where input and output ports or only out-
put ports should be defined for any used VID.
Vlan Configuration Table has 64 position for Vlan ID range from 1 to 4095.

37
7.1.3.2 STM-1 synchronisation
Refer to Fig.16.
STM-1 frame generation requires that it is synchronised to a SDH network.
Into ALplus2 a synchronisation circuit, called SETS, gets the synchronisation signal from the following dif-
ferent sources:
• radio
• STM1
• tributary A/WST
• tributary B
• tributary n
• Lan3
• Lan4
• Internal source
As shown in Fig.16 the clocks extracted from the sources are sent to a selection circuit that chooses one
of the signals depending on the control sent by a selection logic.
This latter acts on the base of alatm roots (LOS-loss of input signal, LTI-loss of timing input, LOS-loss of
frame), on the base of assigned priority and manual forcing.
The selected clock drives an oscillator through a PLL circuit. The oscillator will generate the required syn-
chronisation for the STM-1 frame generation. If no input signals are available the internal oscillator source
is used for the local restart.
Alplus2 synchronisation is not yet implemented.
Radio
Trib A
Trib B/n Synchronisation
Source
for
STM-1 selector
STM-1 interface
Lan3
Lan4
LOS
Logic circuit
LTI
for
Priority Control clock
Manual Forcing synchronisation
Fig.16 - Synchronisation block diagram
38
7.1.4 RIM
The RIM consists of the following main circuits:
• IF part of the QAM modulator
• IF part of the QAM demodulator
• power supply
• telemetry IDU/ODU.
7.1.4.1 Modulator
Signals from LIM are connected to a programmable modulator. It consists of the following circuits:
• recovery low pass filter to eliminate signal periodicity
• two mixers for carrier amplitude and phase modulation process
• 330 MHz local oscillator
• a 90° phase shifter to supply two mixers with two in quadrature carriers
• a combiner circuit to generate the QAM modulation.
The obtained 330 MHz QAM modulated carrier is then sent to the cable interface for connection with ODU.
7.1.4.2 Demodulator
At the receive side, from the cable interface, the 140 MHz QAM modulated carrier is sent to the QAM de-
modulator passing through a cable equalizer circuit.
The QAM demodulator within the RIM extracts the I and Q signals to be sent to the digital part of the de-
modulator within the LIM.
7.1.4.3 Adaptive code modulation
ACM profiles
In ALplus2/ALplus2 radio family uses Adaptive Code and Modulation (ACM) in order to employ the correct
modulation profile depending on the Rx signal quality.
Available ACM profiles are the following:
• 4QAM strong
• 4QAM
• 8PSK
• 16QAM
• 32QAM
• 64QAM
• 128QAM
• 256QAM.

39
These profiles operate in an RF channel with the following bandwidth:
• 7 MHz
• 14 MHz
• 28 MHz
• 56 MHz
ACM switching
The usage of the previous modulation profiles in a fixed channel bandwidth results in a variable capacity.
The criteria defining the necessity of an ACM switching, upshift or downshift, is the Rx S/N ratio.
• Upshift - When there is an increase of received S/N, within the same Channel Spacing, the modu-
lation complexity is increased in the direction from 4QAM strong to 256QAM increasing the spectral
efficiency
• Downshift - When there is a decrease of received S/N, within the same Channel Spacing, the mod-
ulation is reduced in the direction from 256QAM to 4QAM strong reducing the spectral efficiency,
In order to configure properly the radio link using ACM facility, an optimization must be found between
max traffic during good propagation conditions and max availability during bad propagation conditions. To
obtain this purpouse the ACM in ALplus2/ALCplus2 family can be configured via software setting the fol-
lowing parameters: ACM setting and Tx Power mode.
ACM setting
The ACM can vary modulation profiles between two extremes defined by the operator through software
configuration: Upper Modulation and Lower Modulation.
• Upper modulation - When propagation into the given radio channel is in the better condition (high
Rx S/N), the radio link is working at the maximum throughput defined at Upper Modulation: the
highest modulation profile that ACM can employ
• Lower modulation - When propagation into the given radio channel is in the worst condition (low
Rx S/N), the radio link is working at the minimum throughput, defined at Lower Modulation: the
lowest modulation profile that ACM can employ
Tx power mode
Tx power mode can be set as Constant Peak or Constant Average (constant bolometer measurement).
• Constant Peak - Tx power is at maximum at 4QAM and at 256QAM is reduced (typical 4.5 dB) so
the RF Tx amplifier can operate in better linear conditions.
• Constant Average - Tx power is the same at any modulation.
The Tx Power mode is set depending on the modulation license of the user and depending on the Lower
Modulation that has been set.
For example:
In case of a 4QAM licence, all the other modulations must remain into the 4QAM mask. In this condition
Tx power must be Constant Peak (Tx Power Constant Peak Mode = Enable): Max Tx power at 4QAM and
reduced power at all the other modulations.
In case of a 16QAM licence (or higher complexity) and Lower Modulation is set at 4QAM, the emitted spec-
trum must remain into the emitted spectrum defined for 16QAM even if the equipment is transmitting at
4QAM. In this case Tx power must be Constant Average (Tx Power Constant Peak Mode = Disable): Tx
power is always the same at any modulation and typically is the Upper Modulation's power. As an alterna-
tive the Lower Modulation can be set at 16QAM so Tx power Constant Peak can be activated.
With Constant Average Tx power (Tx Power Constant Peak Mode = Disable), the Tx power at 4QAM and
any other modulation is the same of Upper Modulation, so if Upper Modulation is 256QAM the output power
at any modulation is the same of 256QAM which is 4.5 dB less than 4QAM. The result is that enabling
256QAM is a big advantage for traffic but less link budget margin at 4QAM.
40
E1 priority
E1 available tributaries belong to two groups.
One is Permanent E1 equal to High Priority E1 that will never be interrupted during modulation downshift.
Downshift modulation will be limited to the minimum to obtain the selected Permanent E1.
The second group is Extra E1 equal to Low Priority, these tributaries will be interrupted progressively during
modulation downshift. They will start to be cut from the highest e.g. tributaries 16th or 32nd up to the first.
In Tab.9 it is reported the priority of tributaries, the lowest will be cut first.
Ethernet traffic
Once defined the bandwidth, Permanent E1 and Extra E1 at any modulation the amount of Ethernet ca-
pacity is the total radio capacity minus the Permanent + Extra E1 at any modulation.
Tab.9 - E1 priority
Priority ALplus2 ALCplus2
Permanent E1 never Permanent E1 never

Highest
disappears disappears
l
l Tributary A
l WST
l Tributary B
l
l E1 tributary n°1 E1 tributary n°1
l
V E1 tributary n°16 E1 tributary n°16
Lowest
E1 tributary n°32 E1 tributary n°32
7.1.4.4 Power supply
The -48 V battery voltage feeds the IDU and ODU circuitry. The service voltage for the IDU feeding are
achieved through a DC/DC converter for +3.6 V generation and a step down circuit for -5 V.
Both voltages are protected against overvoltages and overcurrents. The same battery running through the
interconnection cable gives the power to the ODU.
An electronic breaker protects the battery against cable failure.
7.1.4.5 Telemetry IDU/ODU
The dialogue IDU/ODU is made-up by the main controller and associated peripherals within the ODU. Con-
trols for ODU management and alarm reporting is performed making use of a bidirectional 388 kbit/s
framed signals.
The transport along the interconnecting cable is carried out via two FSK modulated carriers:
• 17.5 MHz from IDU to ODU
• 5.5 MHz from ODU to IDU.

41
7.2 LOOPS
To control the IDU correct operation a set of local and remote loops are made available. The commands
are forwarded by the WEBLCT/NMS program. Loop block diagram is shown by Fig.17.
7.2.1 Tributary
Tributary local loop
Each input tributary is routed directly to the tributary output upon receiving the command. The Tx line
transmission is still on.
Tributary remote loop
Each tributary directed towards the Rx output line is routed back to the Tx line. The Rx line is still on.
7.2.2 BaseBand
The kind of loop is only local and is activated at BI/BE level. The Tx line is still on.
7.2.3 IDU loop
This kind of loop permits to check the full IDU operation. When activated, the modulator output is connect-
ed to demodulator input.
The loop is assured by converting the frequency of the modulator from 330 MHz to 140 MHz.
42
LIM RIM
Trib. IN 330 MHz

MUX BI MOD to ODU
Trib. rem.
loop
BB loop
330
DEMUX BE
Trib. OUT 140
IDU loop
Fig.17 - IDU loopback

Trib. loc. loop DEM
140 MHz
from ODU
43
10/100BaseT
LAN1 Ethernet
1000BaseT
packet switch
10/100/1000BaseT
LAN2 Port A
1000BaseSX,LX
LAN3
Permanent E1
up to 60E1 Radio
E1
STM-1 cross-connect
Extra E1
STM-2
up to 19E1
16E1
2E1
Up to 80E1
- Permanent = High Priority

- Extra = Low Priority
Fig.18 - ALplus2 with 16E1, 1+0 and 1+1 version, block diagram
44
Ethernet
10/100BaseT packet switch Port A
LAN1
1000BaseT
10/100/1000BaseT
LAN2
Port B
1000BaseSX,LX
LAN3
Permanent E1
up to 60E1 Radio A
E1
STM-1 cross-connect
Extra E1
up to 19E1
STM-2
16E1
E1 WST
Permanent E1
up to 60E1 Radio B
Extra E1
up to 19E1
Fig.19 - ALPlus2 with 16E1, 2x(1+0) configuration, block diagram

45
8 ALCPLUS2 IDU DESCRIPTION
8.1 CONFIGURATION
The IDU of ALCplus2 is available in 1+0 and 1+1 configuration.
Into the IDU there are the following circuits:
• Controller
• LIM
• RIM (one circuit in 1+0 configuration, two circuits in 1+1 configuration).
The IDU of ALCplus2 is one RU subrack.
All the listed circuits are inserted into a single board.
Circuits for others 16xE1 or 32xE1 are inserted into the ALCplus2 IDU, one RU subrack, with exp16E1 or
exp32E1 options.
Please refer to chapter 7 ALPLUS2 IDU DESCRIPTION for any information relevant to functionalities of the
listed circuits.
8.1.1 Switch for ethernet ports
Inside IDU is present an Ethernet switch with 4 external ports (electrical 1000BaseT or optical 1000BaseX)
and one internal. Port 3 and Port 4 have both interfaces, Port 1 and Port 2 are electrical only.
The external interfaces (4operational on 6 present) are placed on the front panel. Internal port is reère-
sented by the local radio stream where, through native Ethernet transport, is connected with the remote
equipment.
For Ethernet switch functionnalities, please refer to chapter 7 ALPLUS2 IDU DESCRIPTION.
8.1.2 Service channels
No service channels ports are available for ALCplus2 IDU.
8.2 ALC BLOCK DIAGRAMS
On Fig.20,Fig.21 and Fig.22 you can find block diagrams of ALCplus2 with 32E1 expansion, with 16E1 ex-
pansion and without any expansion.
46
10/100BaseT
LAN1 Ethernet
1000BaseT
packet switch
10/100/1000BaseT
LAN2 Port A
10/100/1000BaseT
LAN3 1000BaseT,SX,LX
10/100/1000BaseT
LAN4 1000BaseSX,LX
Radio
Permanent E1
1+0
up to 60E1
1+1
E1
STM-1 cross-connect
Extra E1
STM-2
up to 19E1
32E1
2E1
Up to 80E1

Fig.20 - ALCplus2 with 32E1 expansion, 1+0 and 1+1 version, block diagram

47
10/100BaseT
LAN1 Ethernet
1000BaseT
packet switch
10/100/1000BaseT
LAN2 Port A
10/100/1000BaseT
10/100/1000BaseT
LAN4 1000BaseSX,LX
Radio
1+0
1+1
2E1

Fig.21 - ALCplus2 with 2E1, 1+0 and 1+1 version, block diagram
10/100BaseT
LAN1 Ethernet
1000BaseT
packet switch
10/100/1000BaseT
LAN2 Port A
10/100/1000BaseT
10/100/1000BaseT
LAN4 1000BaseSX,LX
16E1 Radio
1+0
1+1
2E1

Fig.22 - ALCplus2 with 16E1, 1+0 and 1+1 version, block diagram
48
9 ODU DESCRIPTION
9.1 ODU VERSIONS
Two ODU versions are available: As and ASN.
In the following pages evenctual differences are pointed out.
The ODU (refer to Fig.23) consists of a two shell alluminium mechanical structure, one shell housing all the
ODU circuits, the other forming the covering plate.
On the ODU are accessible:
• the “N” type connector for cable interfacing IDU and ODU
• the “BNC” connector for connection to a multimeter with the purpose to measure the received field
strength
• a ground bolt.
The 1+1 configuration consists of two 1+0 ODUs mechanically secured to a structure housing the hybrid
(or branching unit) for the antenna connection.
9.1.1 AS ODU
The AS ODU is shown in Fig.23 (single ODU) and in Fig.24 (1+1 ODU with branching unit).
Electrical and mechanical characteristics are listed in a separate addendum relevant to ODU frequency.
9.1.2 ASN ODU
The ASN ODU is shown in Fig.23 (single ODU) and in Fig.24 (1+1 ODU with branching unit).
Electrical and mechanical characteristics are listed in a separate addendum relevant to ODU frequency.
9.2 DESCRIPTION
The blocks that arrange the ODU are the following:

• cable interface
• power supply
• Tx section
• Rx section
• 1+1 branching unit

49
9.3 CABLE INTERFACE
The cable interface permits to interface the cable interconnecting IDU to ODU and viceversa.
It receives/transmits the following signals:
• 330 MHz (from IDU to ODU)

• 140 MHz (from ODU to IDU)
• 17.5 MHz (from IDU to ODU)
• 5.5 MHz (from ODU to IDU)
• remote power supply.
The 17.5 MHz and 5.5 MHz FSK modulated carriers, carry the telemetry channel. This latter consists of two
388 kbit/s streams one from IDU to ODU with the information to manage the ODU (RF power, RF frequen-
cy, capacity, etc...) while the other, from ODU to IDU, sends back to IDU measurements and alarms of the
ODU. The ODU management is made by a µP.
9.4 POWER SUPPLY
The battery voltage is dropped from the cable interface and then sent to a DC/DC converter to generate
three stabilized output voltages to be distributed to the ODU circuitry:
• +3.5 V
• a voltage comprised between +6.2 V and +8.2 V to power MMIC amplifiers operating at different
frequency bands
• a –12 V through an inverter circuit.
Each voltage is protected against overcurrent with automatic restart.

Protection against overvoltage occurs as soon as the output voltage raises more than 15% respect to the
nominal voltage. The restart is automatic.
9.5 TX SECTION
Refer to block diagram shown in Fig.25.
The 330 MHz QAM modulated carrier from the cable interface (see chapter 9.3 CABLE INTERFACE) is for-
warded to a mixer passing through a cable equalizer for cable loss compensation up to 40 dB at 330 MHz.
The mixer and the following bandpass filter give rise to a second IF Tx carrier the frequency of which de-
pends on the go/return frequency value. The mixer is of SHP type.
All the IF and RF local oscillators are μP controlled.
The IF carrier is converted to RF and then amplified making use of a MMIC circuit. The conversion mixer is
SSB type with side band selection.
The power at the MMIC output can be manually attenuated by 40 dB, 1 dB step (20dB, 1dB step for ODU
ASN).
The automatic adjustment is performed making use of an ATPC (see paragraph 9.5.1 ATPC operation for
details). The regulated output power is kept constant against amplifier stage gain variation by a feedback
including the AGC.
Before reaching the antenna side the RF signal at the output of MMIC passes through the following circuits:
• a decoupler plus detector diode to measure the output power
50
• a circulator to protect the amplifier stages against possible circuit mismatch.
• a ON/OFF switch for 1+1 operation
• an RF bandpass filter for antenna coupling.
A particular setting of Tx and Rx RF oscillators allows to obtain a RF Loop, managed by Controller module.
The particular way used to perform the RF loop avoids the necessity to switch off the remote Transmitter.
RF Loop is available in AS ODU only.
9.5.1 ATPC operation
The ATPC regulates the RF output power of the local transmitter depending on the value of the RF level at
the remote terminal. This value has to be preset from the local terminal as threshold high and low. The
difference between the two thresholds must be equal or higher than 3 dB.
As soon as the received level crosses the preset threshold level low (see Fig.28) due to the increase of the
hop attenuation, a microP at the received side of the remote terminal sends back to the local terminal a
control to increase the transmitted power. The maximum ATPC range is 40 dB (ODU AS, 20dB only in ODU
ASN)
If the hop attenuation decreases and the threshold high is crossed then the control sent by the microP
causes the output power to decrease.
9.6 RX SECTION
The RF signal from the Rx bandpass filter is sent to a low noise amplifier that improves the receiver sen-
sitivity. The following down–converter translates the RF frequency to approximately 765 MHz. The conver-
sion mixer is SSB type. The sideband selection is given through a µP control.
A second down converter generates the 140 MHz IF carrier to be sent to the demodulator within the IDU.
The level of the IF carrier is kept constant to –5 dBm thank to the IF amplifier stages, AGC controlled,
distributed in the IF chain. In addition the AGC gives a measure of the receive RF level.
Between two amplifiers a bandpass filter assures the required selectivity to the receiver. The filter is SAW
type and the bandwidth depends on the transmitted capacity.
9.7 1+1 Tx SYSTEM
The two ODUs are coupled to the antenna side via a balanced or unbalanced hybrid.
1+1 Tx switching occurs in the 1+1 hot stand–by 1 antenna or 2 antennas versions as shown in Fig.26 and
Fig.27.
The transmitter switchover is electromechanical type and consists of two ON/OFF switches within the two
ODUs that assure at least 40 dB insulation on the stand–by transmitter.

51
Reference tooth
O-ring
ODU side flange
ASN version
"N"
"BNC"
Ground bolt
AS version
Fig.23 - AS and ASN ODUs
52
ASN version
Suncover (optional)
AS version
Fig.24 - Final 1+1 assembly with AS and ASN ODU

53
54
DC +3.5 V
DC
Step +6.2 to 8.2 V

up
PTx att.
control
-12 V
INV 0 to 40 dB (ODU AS)
-48 V
0 to 20 dB (ODU ASN)
AGC
Tx LO
µP x
N type 330
Cable MHz Cable IF Tx
interface equaliz. T
MMIC
MOD Alarm Alm

388 manag comm
5.5 kbit/s MUX Tx
5.5 loops
MHz MHz DEMUX &
ctrl ctrl
control IF LO
BNC REC DEM unit
17.5 17.5 388
17.5 MHz kbit/s Rx antenna
MHz
MHz side
PRx
Fig.25 - ODU block diagram

meas.
approx.
ctrl 765
MHz
140 LNA
MHz
x
variable bw 140
(capacity MHz
depending) Rx LO
PRx meas AGC

µP

Tx side
SW control
Rx side
Antenna
side
Tx side
SW control
Rx side
Fig.26 - 1+1 hot stand–by 1 antenna
Tx side
SW control
First
antenna
Rx side
Tx side
SW control
Second
antenna
Rx side
Fig.27 - 1+1 hot stand–by 2 antennas

55
Remote PRx
dBm
Local Remote
Tx Rx
Thresh High
PTx actuation PRx recording
Thresh Low level
µP µP
PTx control
Transmission
Rx Tx
of PTx control
Hop attenuation (dB)
Local PTx
dBm
PTx max.
40 dB (ODU AS)
20 dB (ODU ASN)
ATPC range
PTx min.
Hop attenuation (dB)
Fig.28 - ATPC operation
56
Section 3.
INSTALLATION
10 INSTALLATION AND PROCEDURES FOR ENSUR-

ING THE ELECTROMAGNETIC COMPATIBILITY
10.1 GENERAL INFORMATION TO BE READ BEFORE THE INSTALLA-

TION
The equipment is a split mount (indoor-outdoor) radio link system operating in the frequency ranges 4, 6,
7, 8, 13, 15, 18, 23, 25, 28 and 38 GHz, for low, medium and high transport capacity (from 4 up to 622
Mbit/s), designed to establish LAN-LAN connections and PDH/SDH access. For the details related to the
actual used frequency band refer to the label on the equipment.
The system is provided with an integral antenna; however, in case its antenna is not used, it should be
connected to an antenna conforming to the requirements of ETSI EN 302 217-4-2 for the relevant frequen-
cy band.
The equipment is composed by the following separate units:
• radio unit (outdoor) with or without integral antenna
• Baseband (indoor)
This equipment makes use of non-harmonized frequency bands.
Class 2 radio equipment subject to Authorisation of use. The equipment can operate only at the fre-
quencies authorised by the relevant National Authority.
The deployment and use of this equipment shall be made in agreement with the national regulation
for the Protection from Exposure to Electromagnetic Field.
The symbol indicates that, within the European Union, the product is subject to separate collec-
tion at the product end-of-life. Do not dispose of these products as unsorted municipal waste. For more
information, please contact the relevant supplier for verifying the procedure of correct disposal.

57
10.2 GENERAL
The equipment consists of IDU and ODU(s) units and is mechanically made up of a wired 19” subrack (IDU)
and a weather proof metallic container (ODU). The two units are shipped together in an appropriate card-
board box.
After unpacking, mechanical installation takes place followed by electrical connections as described in the
following paragraphs.
10.3 MECHANICAL INSTALLATION
10.3.1 IDU installation
On their sides the subracks making up the several IDU versions are provided with two holes for the M6
screws fastening the subracks to a rack or to a 19” mechanical structure. The front of the IDU mechanical
structure is provided with the holes at the sides. This permits to fasten the subrack to a 19” rack by means
of 4 M6 screws.
10.3.2 IDU installation
ALPlus2 - To avoid overtemperature problems the free space below and above an IDU must be 44 mm
(1RU) minimum.
ALCPlus2 - IDUs can be stacked.
10.4 ELECTRICAL WIRING
The electrical wiring must be done using appropriate cables thus assuring the equipment responds to the
electromagnetic compatibility standards.
The cable terminates to flying connectors which have to be connected to the corresponding connectors on
the equipment front.
Position and pin–out of the equipment connectors are available in this section.
Tab.10 shows the characteristics of the cables to be used and the flying connector types.
58
Tab.10 - Characteristics of the cables
Type of connector terminating

Interconnecting points Type of cable/conductor
the cable
Polarized SUB–D 3W3 female con- Section of each wire ≥ 2.5

Battery
nector sq.mm a
– 75 ohm coaxial cable with

double shield diameter 4.5
mm dielectric in expanded
polyethylene type 2YCC
0.4/2.5 or equivalent
Tributary signals 1.0/2.3 male connector – Alternatively to the above
option, 75 ohm coaxial ca-
ble with double shield, di-
ameter 3.1 mm dielectric in
Teflon type RG179 B/U DS
or equivalent
–120 Ohm balanced four

symmetric pairs with shield
–75 Ohm unbalanced four
coaxial cable pairs with the
Tributary signals 25 pin SUB–D male connector
shield connect to ground
pin (see “11 ALPLUS2 CON-
NECTORS” document for
pin details)
8 conductor cable different

SCSI 50 pin male connector
Tributary signals for 75 Ohm and 120 Ohm
(IDU Plus)
signals
9 conductor cable with

Female type D connector with 9 double brass sheath type
User input/alarm output
pins and shielded holder interconductor DB28.25 or
equivalent
9 conductor cable with

Female type D connector with 9 double brass sheath type
LCT/RS232
pins and shielded holder interconductor DB 28.10 or
equivalent
GND Faston male type Section area ≥ 6 sq. mm.
a. For power cable length longer than 20 m. a section of 4 mm is required.

59
10.5 CONNECTIONS TO THE SUPPLY MAINS
During the final installation, the IDU must be protected by a magneto-thermal switch (not supplied with
the equipment), whose characteristics must comply with the laws in force in one's country.
The disconnection from the supply mains is made disconnecting the connector SUB-D 3W3 from the IDU.
10.6 GROUNDING CONNECTION
Fig.29 and annexed legend show how to perform the grounding connections.
Indoor 3 4
3 4
ODU
unit
1 5
7 IDU 2
unit
(+) (-)
6
Station Local
ground ground
ground
rack
Legend
1 IDU grounding point, faston type. The cross section area of the cable used must be ≥ 4 sq. mm. The
faston is available on the IDU both sides.
2 ODU grounding bolt. The cross section area of the cable used must be ≥ 16 sq. mm
3 IDU–ODU interconnection cable type Celflex CUH 1/4” terminated with N–type male connectors at
both sides.
4 Grounding kit type Cabel Metal or similar to connect the shield of interconnection cable.
5 Matching cable (tail) terminated with SMA or BNT male and N female connectors.
6 Battery grounding point of IDU to be connected to earth by means of a cable with a section area
2.5 sq. mm. Length ≤ 10 m.
7 Grounding cords connected to a real earth internal of station. The cross section area of the cable
must be ≥ 16 sq. mm
Fig.29 - Grounding connection
60
11 ALPLUS2 CONNECTORS
11.1 IDU FRONT PANEL
The front panel of the ALplus2 modular IDU is made up by the front panels of the modules LIM, RIM and
Controller. See Fig.30.
11.1.1 LIM connectors
• Ethernet port 1 electrical, 10/100/1000BaseT RJ45 (see Tab.11)
• Ethernet port 1, 100/1000BaseX SFP-LC
• Ethernet port 2 electrical, 10/100/1000BaseT RJ45 (see Tab.11)
• Ethernet port 3, 100/1000BaseX SFP-LC
Electrical port 1 and port 2 can be configured MDI or MDIX via WEBLCT.
• STM-1 1 in/out SFP

• STM-1 2 in/out SFP
SFP can be I.1, S1.1, L1.1, L1.2, electrical coaxial 1.0/2.3
• Trib 1-8, 75 Ohm and 120 Ohm E1 in/out 50 pin SCSI female
(Tab.12 for 75Ohm and Tab.13 for
120Ohm)
• Trib 9-16, 75 Ohm and 120 Ohm E1 in/out 50 pin SCSI female
(Tab.12 for 75Ohm and Tab.13 for
120Ohm)
E1, 75 Ohm and 120 Ohm interfaces are present in the same connector (different pins).
11.1.2 RIM connectors
• Connector for 50 Ohm interconnection to ODU SMA
• -48 Vdc power supply SUB-D 3W3 (pinout on the panel)
11.1.3 Controller connectors
• LCT, management USB type B (receptable)

• RS232, management SUB-D male 9 pin (see Tab.14)
• USER IN/OUT SUB-D male 9 pin (see Tab.15)
• MNGT/1, management RJ45 (see Tab.16)

61
• MNGT/2, management RJ45 (see Tab.16)
Port MNGT/1 and port MNGT/2 set MDI or MDIX status automatically.
• CH1 service channel RJ45 (see Tab.17, Tab.18, Tab.19)
• CH2 service channel RJ45 (see Tab.20)
• 2 Mbit/s wayside, 120 Ohm E1 in/out RJ45 (see Tab.21)
11.2 IDU BODY CONNECTORS
• Ground connection 6.3 mm male (Faston).
Ethernet Power
IDU-ODU
Port 1 Port 2 Port 3 2xSTM-1 16E1 cable supply
1 2 3 ON 48V
SPEED
PoE
ACT FAIL
LINK
+
-
LINK LINK IDU ODU 48V
ACT ACT WAY
SIDE
+
REM TEST
LCT RS232 USER IN/OUT MNGT/1 MNGT/2 CH1 CH2 2Mb/s -
Management/ Management/ CH1, CH2 2 Mbit/s ON/OFF

Configuration Configuration service wayside
4 user IN
2 alarm OUT channel
Fig.30 - IDU ALplus2 front panel
Tab.11 - 10/100/1000BaseT, RJ45
Function
Pin RJ45
10/100BaseT 1000BaseT
1 Twisted pair IN_P BI_DB+
2 Twisted pair IN_N BI_DB-
3 Twisted pair OUT_P BI_DA+
4 nc BI_DD+
5 nc BI_DD-
6 Twisted pair OUT_N BI_DA-
7 nc BI_DC+
8 nc BI_DC-
62
Tab.12 - 8xE1, 50 pin SCSI female 75 Ohm
Pin 75 Ohm
48 Ground A
23 Tributary 1/9 input
50 Ground A
25 Tributary 1/9 output
47 Ground A
45 Ground A
42 Ground A
43 Ground A
40 Ground A
39 Ground A
36 Ground B
37 Ground B
34 Ground B
33 Ground B
29 Ground B
31 Ground B
28 Ground B
26 Ground B
Note: Join pin 44 with ground A pins, join pin 32 with ground B pins.
25 1
.........................
.........................
50 26
Fig.31 - Pin-out Tributary 50 pin SCSI female

63
Tab.13 - 8xE1, 50 pin SCSI female 120 Ohm)
Pin 120 Ohm
44 Ground A
44 Ground A
44 Ground A
44 Ground A
44 Ground A
44 Ground A
44 Ground A
44 Ground A
32 Ground B
32 Ground B
32 Ground B
32 Ground B
64
32 Ground B
32 Ground B
32 Ground B
2 Tributary 8/16output
32 Ground B
25 1
.........................
.........................
50 26
Fig.32 - Pin-out Tributary 50 pin SCSI female
Tab.14 - RS232 SUB-D 9 pin male
Pin Description
1 DCD (IN)
2 RD (IN)
3 TD (OUT)
4 DTR (OUT)
5 GND
6 Not connected
7 RTS (OUT)
8 CTS (IN)
9 Not connected

65
Tab.15 - SUB-D 9 pin male USER IN/OUT)
Pin Description
1 C relay contact- branch 1
2 NA/NC relay contact - branch 1
3 C relay contact - branch 2
4 NA/NC relay contact - branch 2
5 User input 01
6 User input 02
7 User input 03
8 User input 04
9 Ground
Tab.16 - MNGT/1 and MNGT/2 100BaseT connector pin-out for 10/100BaseT Ethernet connec-
tion (RJ45)
Pin Description
1 Tx+
2 Tx-
3 Rx+
4 --
5 --
6 Rx-
7 --
8 --
Tab.17 - CH1 connector pin-out for 9600 bit/s synchronous V.24 interface (RJ45)
Pin Description
1 CKTx (OUT)
2 TD (IN)
3 DTR (IN)
4 DSR (OUT)
5 GND
6 RD9600 (OUT)
7 CKRx (OUT)
8 DCD (OUT)
66
Tab.18 - CH1 connector pin-out for 9600 bit/s asynchronous V.24 interface (RJ45)
Pin Description
1 --
2 TxD (IN)
3 DTR (IN)
4 DSR
5 GND
6 RxD (OUT)
7 --
8 DCD (OUT)
Tab.19 - CH1 connector pin-out for 1x9600 or 2x4800 kbit/s V.28 interface (RJ45)
Pin Description
1 --
2 TD (1° ch 9600 or 4800) (IN)
3 TD (2° ch 4800) (IN)
4 --
5 GND
6 RD (1° ch 9600 or 4800) (OUT)
7 --
8 RD (2° ch 4800) (OUT)
Tab.20 - CH2 connector pin-out for 64 kbit/s channel - V.11 interface (RJ45)
Pin Description
1 D-V11-Tx
2 D+V11-Tx
3 C-V11-Tx
4 C+V11-Tx
5 D-V11-Rx
6 D+V11-Rx
7 C-V11-Rx
8 C+V11-Rx

67
Tab.21 - 2 Mbit/s wayside connector pin-out (RJ45)
Pin Description
1 Tx-C (IN) common
2 TX-F (IN) 120 Ohm
3 GND
4 TX-F (IN) 75 Ohm
5 Rx-C (OUT) common
6 Rx-F (OUT) 120 Ohm
7 GND
8 Rx-F (OUT) 75 Ohm
68
12 ALCPLUS2 CONNECTORS
12.1 IDU FRONT PANEL
The front panel of the ALCplus2 IDU is made up by various connectors depending on IDU version: in the
following type of connectors and relevant pin-out are listed. On the body of each IDU there is the ground
connection: 6.3mm male (Faston).
12.2 ALCplus2 1+0/1+1 (GAI0157/GAI0152)
In Fig.8 and Fig.9 are shown the 1+0 and 1+1 version. The following connectors are available:
• MNGT1, 2 management
Port MNGT 1, 2 set MDI or MDIX status automatically RJ45 (Tab.16)
• LAN port 1, 2, 3, 4 electrical 10/100/1000BaseT

Electrical port 1, 2, 3, 4 can be configured
MDI or MDIX via WEBLCT RJ45 (Tab.11)
• LAN port 3, 4 100/1000BaseX SFP-LC

• Trib A, B RJ45 (Tab.22)
• USER IN/OUT SUB-D male 9 pin (Tab.23)
• Connector for 50 Ohm interconnection to ODU

1 connector 1+0, 2 connectors in 1+1 SMA
• -48 Vdc power supply

1 connector in 1+0, 2 connectors in 1+11 SUB-D 3W3 (pinout on the panel)
Tab.22 - Trib A, B connector
PIN RJ45 Function
1 Rx-F (OUT) 120 Ohm
2 Rx-C (OUT) 120 Ohm common
3 GND
4 Tx-F (IN) 120 Ohm
5 Tx-C (IN) 120 Ohm common
6 Tx-F (IN) 75 Ohm
7 GND
8 Rx-F (OUT) 75 Ohm
1 In 1+1 the two power supply connectors are in parallel

69
Tab.23 - SUB-D 9 pin male USER IN/OUT
PIN RJ45 Function
1 C relay contact
2 NO relay contact
3 User Input 01
4 User Input 02
5 Ground
6 Do not use
7 NC relay contact
8 Not connected
9 Do not use
12.3 ALCplus2 16E1 1+0/1+1 (GAI0155/GAI0156)
In Fig.10 and Fig.11 are shown the 1+0 and 1+1 version. The following connectors are presents:

DI or MDIX via WEBLCT RJ45 (Tab.11)

• Trib 1/8, 9/16

E1, 75 Ohm and 120 Ohm interfaces are present
in the same connectors (different pins) 50 pin SCSI female (Tab.12 for 75 Ohm
and Tab.13 for 120 Ohm)


1
1 connector in 1+0, 2 connectors in 1+1 SUB-D 3W3 (pinout on the panel)
12.4 ALCplus2 NODAL 1+0/1+1 (GAI0163/GAI0162)
In Fig.14 and Fig.15 are shown the 1+0 and 1+1 version. The following connectors are present:

70
• STM-1 1, 2 in/out
SFP can be I.1, S1.1, L1.1, L1.2, electrical coaxial 1.0/2.3 SFP
• N-BUS 1, 2 connection among IDUs only

through SIAE cable F03471

• Trib 1/8, 9/16

in the same connectors (different pins) 50 pin SCSI female (Tab.12 for 75 Ohm
and Tab.13 for 120 Ohm)


1 connector in 1+0, 2 connectors in 1+1 1 SUB-D 3W3 (pinout on the panel)
12.5 ALCplus2 32E1 1+0/1+1 (GAI0169/GAI0168)
In Fig.12 and Fig.13 are shown the 1+0 and 1+1 version. The following connectors are present:

• STM-1 1, 2 in/out
SFP can be I.1, S1.1, L1.1, L1.2, electrical coaxial 1.0/2.3 SFP

• N-BUS 1, 2 connection among IDUs only

through SIAE cable F03471
• Trib 1/8, 25/32

in the same connectors (different pins) 50 pin SCSI female (Tab.12 for
75 Ohm and Tab.13 for 120 Ohm)


1 connector in 1+0, 2 connectors in 1+1 1 SUB-D 3W3 (pinout on the panel)

71
13 INSTALLATION ONTO THE POLE OF THE ODU
WITH SEPARATED ANTENNA
13.1 INSTALLATION KIT
Following installation kits are supplied with the equipment depending on different versions:
• 1+0 version
- antisliding strip (see Fig.33)
- supporting plate plus 60–114 mm pole fixing bracket and relevant nuts and bolts (see Fig.34)
- adapting tools and relevant bolts and nuts for 219 mm pole (see Fig.35)
- Band-it fixing system (see Fig.38)
- antenna side flange, variable as function of RF frequency (see Fig.36)
- support with ODU fast locking mechanism (see Fig.34)
- connection to the antenna with flexible wave guide and possible use of a rigid elbow (optional)
(see Fig.36)
- kit for ground connection making part of ODU
• 1+0 version (6 GHz only)
Besides the previous items a specific flange adaptor (kit V32409) must be used (see Fig.44). The
flange is UDR70.
• 1+1 version
- antisliding strip (see Fig.33)
- supporting plate plus pole fixing bracket and relevant nuts and bolts (see Fig.34)
- adapting tools and relevant bolts and nuts for 219 mm pole (see Fig.35)
- hybrid with ODU fast locking mechanism (see Fig.37)
- flexible waveguide trunk for connection to antenna (optional) (see Fig.36)
- kit for ground connection making part of the two ODUs.
flange is UDR70.
Warning: in order to avoid damages to flexible waveguides, don’t fold or twist them more than values
specified as limit in installation instructions of the waveguide supplier.
In case of flexible wave guide use, Tab.26 shows the maximum bending radius.
72
13.2 REQUIRED TOOLS FOR MOUNTING (NOT SUPPLIED)
• N.2 13mm torque wrench
• N.1 15 mm torque wrench

• N.1 3 mm Allen wrench
Warning: if screwing operation concerns more than one screw or bolt, tighten subsequently everyone and
its opposite, step by step.
13.3 INSTALLATION PROCEDURE
Installation procedure proceeds according to the following steps:
• Version 1+0: installation onto the pole of the supporting plate 2
• Version 1+0: installation onto the pole of the support plate by Band-it
• Version 1+1: installation onto the pole of the supporting plate 2
• Installation of the ODU (common to both 1+0 and 1+1 version)
• ODU grounding
1+0 version – Installation onto the pole of the supporting plate
Fig.33 – Mount antislide strip around the pole. The position of the plastic blocks depends on the position
of the supporting plate (see next step)
Fig.34 – Adhere the supporting plate to the antisliding strip plastic blocks and then secure it to the pole
through the fixing bracket for 60–114 mm pole (see Fig.34). Bolts and nuts are available on the supporting
plate. Tightening torque must be 32 Nm.
Warning: As shown in Fig.35 an adapting kit must be used for the 219 mm pole. It consists of an additional
plate to enlarge the standard supporting plate dimension and relevant U–bolt for 219 mm pole fixing.
Fig.36 – Fix the flexible waveguide to the antenna side flange. Four fixing screws are available the dimen-
sions of which depend on the waveguide type. Tighten progressively and alternatively the four screws with
the following torque:
Tab.24 - Torques for tightening screws
Frequencies Screw Tool Torque
from 18 to 38 GHz Allen screw M3 Allen key 2.5 mm 1 Nm
up to 15 GHz Allen screw M4 Allen key 3 mm 2 Nm
Fig.36 – Fix the antenna side flange to the support with ODU fast locking mechanism. The flange can be
mounted horizontally (as shown in Fig.36) or vertically as function of convenience.
Fig.37 – Fix the support with ODU fast locking mechanism to the supporting plate making use of available
bolts and nuts. Fig.37 shows the possible positions. Tightening torque must be 18 Nm.
2 In case of 219 mm pole, an adapting kit is supplied for the purpose.

73
1+0 version – Installation onto the pole of the supporting plate by Band-it
In case of 1+0 ODU installation, a Band-it pole mounting kit can be used: through slots (see Fig.38) on
the supporting plate two metallic bands secure the plate on the pole. Band characteristics are:
• thickness 0.76 mm
• width 19 mm.
It is also possible to use the anti-sliding system (optional).
1+1 version – Installation onto the pole of the supporting plate
Fig.33 – Mount antislide strip around the pole. The position of the plastic blocks depends on the position
of the supporting plate (see next step)
Fig.34 – Position the supporting plate to the antisliding strip plastic blocks and then secure it to the pole
through the fixing bracket for 60–114 mm pole (see Fig.34). Bolts and nuts are available on the supporting
plate kit. Tightening torque must be 32 Nm.
Fig.39 – Secure the hybrid with ODU fast locking mechanism to the supporting plate using bolt and nuts
available on the support plate. Tightening torque must be 18 Nm.
Remove the plastic cover from the hybrid flange sides.
Warning: Do not remove the foil from the hybrid flange sides.
Warning: It is advisable to shape the waveguide flexible trunk, connecting ODU flange with antenna flange
as shown in Fig.42. This avoids possible condensate to be channelled towards the ODU flange.
Installation of the ODU
1 Remove the plastic cover from the ODU flange side. Apply silicon grease e.g. type RHODOSIL PATE
4 to the O–ring of Fig.41.
Warning: Do not remove the foil from the flange.
2 Bring the ODU with the two hands and position the ODU handle at the bottom side.
3 Position the ODU body close to the support with ODU fast locking mechanism and align ODU side
flange (see Fig.41) to antenna side flange (see Fig.36 – 1+0 version) or hybrid side flange (see
Fig.39 – 1+1 version).
Note: For 1+0 version the ODU can assume positions of Fig.40 depending on the polarisation.
4 With respect to the flange alignment, turn the ODU body approx. 30° anti–clockwise and then insert
the ODU body into the support and search for alignment between reference tooth on the support
(see Fig.36 – 1+0 version or Fig.39 – 1+1 version) and ODU body reference tooth (see detail Fig.41)
5 When alignment is achieved, turn the ODU body clockwise until “clack” is heard and the ODU rota-
tion stops.
6 Secure ODU body on the support by tightening bolts (1) (see Fig.36 – 1+0 version or Fig.39 – 1+1
version). Tightening torque must be 6 Nm.
Final assembly of 1+1 version is shown in Fig.42. A parasol mounting is optionally possible.
74
13.4 GROUNDING
The ODU must be connected to ground making reference to details of Fig.43.
Tab.26 - Waveguide bending radius according to frequency
Bending radius Bending radius Bending radius Bending radius

without rebending without rebending with rebending with rebending
Frequency
mm (inch) mm (inch) mm (inch) mm (inch)
E-plane a H-plane b E-plane a. H-plane b.
6 GHz or 7 GHz
200 (7,9) 500 (19,8) 300 (11,9) 600 (23,7)
low
7 GHz high 200 (7,9) 500 (19,8) 250 (9,9) 600 (23,7)
11 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
13 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
15 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
18 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
23 GHz 110 (4,3) 230 (9,1) 130 (5,1) 250 (9,9)
38 GHz 80 (3,1) 140 (5,5) 90 (3,6) 150 (5,9)
a. Bending E-plane
Rmin/E
Bending E-plane
(short side of the section)
b. Bending H-plane
Rmin/H
Bending H-plane
(long side of the section)

75
Plastic blocks
Antisliding strip
Fig.33 - Antisliding strip
76
Use 17 mm wrench
(32Nm torque)
Supporting plate
Use 15 mm wrench
(32Nm torque)
Fig.34 - 60–114 mm pole supporting plate fixing

77
Fig.35 - Adapting kit for 219 mm pole
78
In option
Antenna side flange
Support with ODU fast

lockinh mechanism
Reference tooth
Reference tooth
1
1
Position of antenna
side flange
1 13 mm wrench
6 Nm torque
Fig.36 - Mounting position

79
A
Adapting kit for 219 mm pole
B C
Fig.37 - Possible positions of the support with ODU fast locking mechanism
80
Fig.38 - Band-it pole mounting kit

81
Use 13 mm wrench
(18 Nm torque)
Hybrid with ODU fast

locking mechanism
Reference tooth Reference tooth
Optional vawe
guide
RT1 RT2
Fig.39 - Installation onto the pole of the supporting plate
82
Vertical Horizontal
Fig.40 - Position of the ODU body depending on the polarisation for 1+0. For 1+1 the polarisa-
tion is always vertical: handle at the left side.

83
Reference tooth
O-ring
ODU side flange
ASN version
"N"
"BNC"
Ground bolt
AS version
Fig.41 - ODU body reference tooth
84
ASN version
Suncover (optional)
AS version
Fig.42 - Final ODU assembly of 1+1 version

85
1
2
3
4
5
ASN version
AS version
Fig.43 - ODU grounding
86
Spring
Washer
Screw M5x25
UDR70 antenna flange
Screw M4x8
Fig.44 - Kit V32409

87
UDR70 flange
Screw M4x18
Spring
Washer
O-Ring
Hybrid 6 GHz
(balanced or
unbalanced)
Fig.45 - Kit V32415
88
14 INSTALLATION ONTO THE WALL OF THE ODU
WITH SEPARATED ANTENNA
• 1+0 version
- wall supporting plate with additional contact surface extension plates (see Fig.46)
- antenna side flange, variable as function of RF frequency (see Fig.47)
- support with ODU fast locking mechanism (see Fig.47)
(see Fig.47)
- kit for ground connection making part of ODU
flange is UDR70.
• 1+1 version
- supporting plate with additional contact surface extension tools (see Fig.46)
- hybrid with ODU fast locking mechanism (see Fig.49)
(see Fig.47)
- kit for ground connection making part of the two ODUs.
flange is UDR70.
In case of flexible wave guide use, Tab.29 shows the maximum bending radius.
• N.2 13mm torque wrench
• N.1 3 mm allen wrench.

89
Installation procedure proceeds according to the following steps:
• version 1+0: installation onto the wall of the supporting plate
• version 1+1: installation onto the wall of the supporting plate

• installation of the ODU (common to both 1+0 and 1+1 version)
• ODU grounding.
1+0 version – Installation onto the wall of the supporting plate
Fig.46 – Fix on the supporting plate the two supplied extension plates to increase the wall contact surface.
Fig.46 – Secure the supporting plate on the wall using the more suitable screws.
Fig.47 – Fix the antenna side flange to the support with ODU fast locking mechanism. The flange can be
mounted horizontally (as shown in Fig.47) or vertically as function of convenience.
Fig.48 – Fix the support with ODU fast locking mechanism to the supporting plate making use of available
bolts and nuts. Fig.48 shows three possible positions. Tightening torque must be 18 Nm.
1+1 version – Installation onto the wall of the supporting plate
Fig.46 – Fix on the supporting plate the two supplied extension plates to increase the wall contact surface.
Fig.46 – Secure the supporting plate on the wall using the more suitable screws.
Fig.49 – Secure the hybrid with ODU fast locking mechanism to the supporting plate using bolt and nuts
available on the support plate. Tightening torque must be 18 Nm.
Remove the plastic cover from the hybrid flange sides.
Warning: Do not remove the foil from the hybrid flange sides.
Warning: It is advisable to shape the waveguide flexible trunk, connecting ODU flange with antenna flange
as shown in Fig.52 This avoids possible condensate to be channelled towards the ODU flange.
90
Installation of the ODU
1 Remove the plastic cover from the ODU flange side. Apply silicon grease e.g. type RHODOSIL PATE
4 to the O–ring of Fig.51.
Warning: Do not remove the foil from the flange.
2 Bring the ODU with the two hands and position the ODU handle at the bottom side.
3 Position the ODU body close to the support with ODU fast locking mechanism and align ODU side
flange (see Fig.51) to antenna side flange (see Fig.47 – 1+0 version) or hybrid side flange (see
Fig.49 – 1+1 version).
Note: For 1+0 version the ODU can assume positions of Fig.50 depending on the polarisation.
4 With respect to the flange alignment, turn the ODU body approx. 30° anti–clockwise and then insert
the ODU body into the support and search for alignment between reference tooth on the support
(see Fig.47 – 1+0 version or Fig.49 – 1+1 version) and ODU body reference tooth (see detail Fig.51)
tion stops.
6 Secure ODU body on the support by tightening bolts (1) (see Fig.47 – 1+0 version or Fig.49 – 1+1
version). Tightening torque must be 6 Nm.
Final assembly of 1+1 version is shown in Fig.52. A parasol mounting is optionally possible.

91
14.4 GROUNDING
The ODU must be connected to ground making reference to details of Fig.53.
Tab.29 - Waveguide bending radius according to frequency
Bending radius Bending radius Bending radius Bending radius

without rebending without rebending with rebending with rebending
Frequency
mm (inch) mm (inch) mm (inch) mm (inch)
E-plane a H-plane b E-plane a. H-plane b.
6 GHz or 7 GHz
200 (7,9) 500 (19,8) 300 (11,9) 600 (23,7)
low
7 GHz high 200 (7,9) 500 (19,8) 250 (9,9) 600 (23,7)
11 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
13 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
15 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
18 GHz 130 (5,1) 280 (11,0) 150 (5,9) 300 (11,9)
23 GHz 110 (4,3) 230 (9,1) 130 (5,1) 250 (9,9)
38 GHz 80 (3,1) 140 (5,5) 90 (3,6) 150 (5,9)
a. Bending E-plane
Rmin/E
Bending E-plane
(short side of the section)
b. Bending H-plane
Rmin/H
Bending H-plane
(long side of the section)
92
Extension plate
Supporting plate
M8 bolt and nut
Another possible fixation
Fig.46 - Wall supporting plate

93
In option
Antenna side flange
Support with ODU fast

locking mechanism
Reference tooth
Reference tooth
1
1
13 mm wrench
6 Nm torque
Position of antenna
side flange
Fig.47 - Support with ODU fast locking mechanism
94
Fig.48 - Mounting possible positions

95
Use 13 mm wrench
(18 Nm torque)
Hybrid with ODU fast

locking mechanism
Reference tooth Reference tooth
Optional wave
guide
RT1 RT2
Fig.49 - Installation onto the wall of the supporting plate
96
Vertical Horizontal
Fig.50 - Position of the ODU body depending on the polarisation for 1+0. For 1+1 the polarisa-
tion is always vertical: handle at the left side.

97
Reference tooth
O-ring
ODU side flange
ASN version
"N"
"BNC"
Ground bolt
AS version
98
Suncover (optional)
ASN version
AS version
Fig.52 - Final ODU assembly of 1+1 version

99
1
2
3
4
5
ASN version
AS version
1 Bolt
2 Spring washer
3 Flat washer
4 Earth cable collar
5 Flat washer
100
Spring
Washer
Screw M5x25
UDR70 antenna flange
Screw M4x8
Fig.54 - Kit V32409

101
UDR70 flange
Screw M4x18
Spring
Washer
O-Ring
Hybrid 6 GHz
(balanced or
unbalanced)
Fig.55 - Kit V32415
102
WITH INTEGRATED ANTENNA
15.1 FOREWORD
The installation onto the pole of the ODU with integrated antenna concerns both 1+0 and 1+1 versions.
1+0 version
• 60 to 114 mm pole mounting kit consisting of:
- centring ring and relevant screws (see Fig.56)
- antislide strip (see Fig.57)
- pole support system and pole fixing brackets (see Fig.58)
- ODU with O–ring and devices for ground connection
1+1 version
• pole mounting kit from 60 to 114 mm for 1+1 consisting of:
- centring ring and relevant screws (see Fig.56)
- antislide strip (see Fig.57)
- pole support system and pole fixing brackets (see Fig.58)
• hybrid mechanical body (see Fig.67)
• polarization twist disk (see Fig.69)
• 2 ODUs with O–rings and devices for ground connection.

103
• N.1 3 mm allen wrench.
Installation procedure proceeds according with the following steps:
1+0 version
1 installation onto the pole of the support system

2 installation of the antenna
3 installation of ODU
4 antenna aiming
5 ODU grounding
1+1 version
1 installation onto the pole of the support system
2 installation of the antenna
3 installation of hybrid circuit
4 installation of the two ODUs
5 antenna aiming
6 ODU grounding.
15.4.1 Installation onto the pole of the support system and the antenna
Fig.56 – Set the antenna in such a position as to be able to operate on its rear side. Locate the five threaded
holes around antenna flange. Mount centring ring onto antenna flange and tight it with 3 calibrated bolts.
Caution: centring ring should be mounted so that the screws do not stick out.
Define if the antenna will be mounted with vertical or horizontal polarization. Check that free drain holes
stay at bottom side. Mount bolt type M10x30, in position A leaving it loose of 2 cm approx. With horizontal
polarization mount bolt type M10x30 in position D, leaving it loose of 2 cm approx.
Fig.57 – Mount antislide strip onto the pole. Place blocks as in Fig.57 following antenna aiming direction.
Tighten the strip with screwdriver.
Fig.58 – Mount pole supporting system with relevant pole fixing brackets following antenna aiming direc-
tion as indicated by arrow. Antislide strip should result at the centre of supporting plate. Supporting system
should lean against antislide clamp with the tooth as in Fig.59. Position the antenna in such a way that bolt
104
in position A or D of Fig.56 cross through hole E of Fig.60. Secure the support system to the pole by means
of the pole fixing brackets and relevant fixing bolts.
Fig.61 – Rotate the antenna body until the remainder three antenna holes coincide with the three support
holes. Secure the antenna to the support by thightening the relevant passing through bolts.
15.4.2 Installation of ODU
1+0 version
1 Apply silicon grease e.g. RHODOSIL PATE 4” to the O–ring (4) of Fig.64 by protecting finger hands
with gloves.
2 Bring the ODU with the two hands and position the ODU handle at the bottom side. The ODU handle
can assume position of Fig.62 depending on the polarization.
3 Position the ODU body near the support system and align ODU side flange to antenna side flange
(see Fig.63). With respect to the flange alignment, turn the ODU body approx. 30° anti–clockwise
and then insert the ODU body into the support and search for alignment between reference tooth
on the support (see Fig.63) and ODU body reference tooth (see detail of Fig.64).
tion stops.
Fig.65 and Fig.66 show ODU housing final position for vertical and horizontal polarization respec-
tively.
5 Secure ODU body on the support system by tightening bolts (1) of Fig.63.
1+1 version
Fig.67 – Apply silicon grease, type “RHODOSIL PATE 4” to O–rings (1). Insert O–rings (1) and (6) into twist
polarization disk (2).
Vertical polarization
Fix the disk on hybrid flange placing marker (4), on disk, close to V mark.
Horizontal polarization
Fix the disk on hybrid flange placing reference (4), on disk, close to H mark.
In 13 GHz and 15 GHz ODUs the polarization disk is fixed to the hybrid flange by means of 3 screws as
shown in Fig.68.
Caution: Twist disk has two planes. Take care of position marker (4) on twist disk. The position of marker
(4) plane should be in contact to hybrid like in figure. Tighten progressively and alternatively screws (7)
with the same number of spring washers (8) with the following torque:
Fig.69 – Fix hybrid to support system with four bolts (1) taking care of RT1/RT2 position shown by labels
of Fig.69. Tighten progressively and alternatively four bolts (1).

105
15.4.3 ODU installation
The installation procedure of the two ODUs is the same.
1 Apply silicon grease e.g. RHODOSIL PATE 4” to the O–ring (4) of the Fig.64 by protecting finger
hands with gloves.
2 Bring the ODU with the two hands and position the ODU handle at the bottom side. For 1+0 the
ODU can assume position of Fig.62 depending on the polarisation. For 1+1 the handle ODU position
is always placed at the right side (horizontal polarization).
3 Position the ODU body near the support system and align ODU side flange to antenna side flange
(see Fig.63). With respect to the flange alignment, turn the ODU body approx. 30° anti–clockwise
and then insert the ODU body into the support and search for alignment between reference tooth
on the support (see Fig.63) and ODU body reference tooth (see detail of Fig.64).
tion stops.
Fig.65 and Fig.66 show ODU housing final position for vertical and horizontal polarization respec-
tively for 1+0 version.
Fig.70 shows ODU housing final position for 1+1 version.
5 Secure ODU body on the support system by tightening bolts (1) of Fig.63.
15.5 ANTENNA AIMING
Antenna aiming for 1+0 version and 1+1 version is the same. The antenna aiming devices allow to perform
the following adjustments with respect to the starting aiming position:
- Horizontal ± 15° operating on the nut (3) shown in Fig.71, only after having loosen
the nuts (7), (8), (9), (10) of Fig.72.
- vertical ± 15° operating on vertical adjustment worm screw (2) shown in Fig.71
only after having loosen nuts (1), (2), (11) of Fig.72 and (4) and (5) of
Fig.71.
For adjustment from 0° to +30° extract nut (1) Fig.72 and position it in
hole (4), extract nut (2) Fig.72 and position it in hole (6). Operate on
vertical adjustment worm screw (2) after having loosen nuts (1), (2), (11) of
Fig.72 and (4) of Fig.71.
For adjustment from 0° to –30° extract nut (1) of Fig.72 and position it in
hole (3), extract nut (2) of Fig.72 and position it in hole (5). Operate on
vertical adjustment worm screw (2) after having loosen nuts (1), (2), (11) of
Fig.72 and (4) of Fig.71.
For vertical adjustment some markers, every 10°, are available on support.
The bigger marker gives 0° starting aiming position. Once the optimum aiming
position is obtained, tighten firmly the four nuts (1), (2), (11) of Fig.72 and
(4) and (5) of Fig.71 for vertical adjustment and the four nuts (7), (8), (9),
(10) of Fig.72 for horizontal adjustment. Tighten with 15 mm wrench and
32 Nm torque.
15.6 COMPATIBILITY
The pole installation kit of the ODU unit in 1+0 and 1+1 configuration is compatible with integrated antenna
complying with SIAE standard with measures 0.2 m, 0.4 m, 0.6 m, 0.8 m of diameter.
106
15.7 GROUNDING
See Fig.73.
On ODU grounding can be connected with the available bolt spring washer and flat washers as shown.

107
A D D C
B C A B
Vertical polarization horizontal polarization
3 mm allen key 2
2,5 Nm torque
A
1
C
1 Antenna
2 Calibrated Allen screw
3 Centring ring
Fig.56 - Centring ring position
108
2
1 Steel belt
2 Plastic blocks
Fig.57 - Antislide strip

109
1
Antenna aiming direction

3
15 mm wrench
32 Nm torque 3
3 3
3
1 Pole fixing brackets
2 Tooth
3 Bolt
4 Pole support system
Fig.58 - Support mount on pole
110
Antenna aiming direction
1 Tooth
Fig.59 - Supporting system position
Fig.60 - Hole E

111
B C
A D
15 mm wrench
32 Nm torque
A, B, C, D Bolt slots
Fig.61 - Antenna installation on pole support
Vertical Horizontal
Fig.62 -Position of the ODU handle depending on the polarisation for 1+0. For 1+1 the polari-
sation is always horizontal. Handle at the right side.
112
1 13 mm wrench
6 Nm torque
H
H
H
H
1
1
H
H
H
H
1
H: Reference tooth
Fig.63 - Support system for ODU housing and reference tooth in evidence

113
Reference tooth
O-ring
ODU side flange
ASN version
"N"
"BNC"
Ground bolt
AS version
114
5
30
Fig.65 - ODU housing final position for vertical polarization
5
30
5
30
Fig.66 - ODU housing final position for horizontal polarization

115
7
2
4
6
1 O–ring
2 Polarization twist disk
3 Hybrid mechanical body
4 Position marker of twist disk

5 Reference label for twist disk
6 O–ring
7 Allen screws
8 Spring washer
Fig.67 - Hybrid and polarization disk
116
Fig.68 - Polarization disk fixing (only for 13GHz and 15 GHz)

117
1
RT1
2
1
RT2
13 mm wrench
18 Nm torque
1 Bolts
2 Spring washer
Fig.69 - Hybrid mount on pole support
118
ASN version
AS version
Fig.70 - ODU housing final position for 1+1 version

119
3
4
5 1
2
1 Marker
2 Vertical adjustment
3 Horizontal adjustment
4 Bolt
5 Fixing nut
Fig.71 - Vertical and horizontal adjustments
120
15 mm wrench 15 mm wrench
32 Nm torque 32 Nm torque
7
4 11 1 8
3
10
9 15 mm wrench
6 32 Nm torque
5 2
15 mm wrench
32 Nm torque
1., 2., 3., 4. Horizontal aiming block bolts
5., 6., 7. Vertical aiming block bolts
8., 11. Threaded hole for vertical aiming up to –30°
9., 10. Threaded hole for vertical aimimg up to +30°
Fig.72 - Antenna aiming block

121
1
2
3
4
5
ASN version
AS version
1 Bolt
2 Spring washer
3 Flat washer
5 Flat washer
122
WITH INTEGRATED ANTENNA (KIT V32307,
V32308, V32309)
16.1 FOREWORD
The description concerns pole mounting of ODU, in 1+0 and 1+1 version, using following installation kits:
- V32307 for ODU with frequency from 10 to 13 GHz
Differences regard the dimensions and the presence of the centring ring (see Fig.74):
- V32307 centring ring for antenna flange from 10 to 13 GHz
- V32308 centring ring for antenna flange from 15 to 38 GHz
- V32309 no centring ring (and relevant screws).
Following installation kits are supplied with the equipment depending on different versions.
1+0 version
• 60 to 129 mm pole mounting kit:
- centring ring and relevant screws
- pole support system plus antenna (already assembled) and pole fixing brackets
- 1+0 ODU support and relevant screws

1+1 version
- 1+0 ODU support
- hybrid and relevant screws
- polarization twist disk and relevant screws
- 2 ODUs with O–rings and devices for ground connection.

123
• N.1 2.5 mm Allen wrench

• N.1 13 mm spanner
• N.2 17 mm spanner.
Installation procedure is listed below:
1+0 version
1 antenna polarization
2 installation of the centring ring on the antenna

3 installation of 1+0 ODU support
4 installation onto the pole of the assembled structure
6 antenna aiming
7 ODU grounding
1+1 version

5 installation of hybrid
6 installation of ODUs
7 antenna aiming
8 ODU grounding.
124
16.5 1+0 MOUNTING PROCEDURES
16.5.1 Setting antenna polarization
Fig.74 – Set the antenna in such a position to operate on its rear side. Locate the four M3 Allen screws
around the antenna flange. Unscrew them (use 2.5 mm Allen wrench) and position the antenna flange ac-
cording on: horizontal wave guide –> vertical polarization, vertical wave guide –> horizontal polariza-
tion. Screw again the four Allen screws (torque = 1 Nm).
16.5.2 Installation of the centring ring on the antenna
Fig.74 – Set the antenna in such a position to operate on its rear side. Locate the three holes around the
antenna flange. Mount the centring ring onto antenna flange and tight it with the 3 Allen screws M4 (use
3mm Allen wrench, torque 2 = Nm).
16.5.3 Installation of 1+0 ODU support
Fig.74 – Mount the support onto assembled structure (pole support system plus antenna) using the four
M8 Allen screws (use 6 mm Allen wrench, torque 18 = Nm). Two of the four screws, diagonally opposed,
must be mounted with the two bushes around.
16.5.4 Installation onto the pole of the assembled structure
Fig.74 – Mount the assembled structure on the pole using the two pole fixing brackets and the four M10
screws (use 17 mm spanner, torque = 13 Nm); the heads of the screws are inserted on the antenna side,
the four nuts and the springs between nut and brackets are inserted on bracket side.
16.5.5 Installation of ODU (on 1+0 support)
Fig.75 – Apply silicon grease (e.g. RHODOSIL PATE 4”) on the O–ring by protecting fingers with gloves.
Fig.76 – Bring the ODU with the two hands and position the ODU handle at the bottom side. The handle
can assume the positions shown in the figure depending on the polarization. Position the ODU body near
the support and align the wave guide of the ODU to the Wave guide of the antenna: respect to the position
of wave guide alignment, turn the ODU body approx. 30° counter–clockwise into the support and search
for matching between reference tooth on the support (see Fig.77) and reference tooth on the ODU body.
Fig.78 – When alignment of the references teeth is achieved, turn the ODU body clockwise until rotation is
stopped. In figure are shown ODU final position for both polarizations.
Fig.77 – When ODU positioning is over, secure ODU body on the support by tightening bolts (use 13mm
spanner, torque = 6Nm).

125
16.5.6 Antenna aiming
Antenna aiming procedure for 1+0 version or 1+1 version is the same.
Horizontal aiming: ±5° operating on the 17 mm nut shown in Fig.79 with a 17 mm spanner, only after
having loosen the two 17 mm nut on the pivot.
Vertical aiming: ±20° operating on the 13 mm nut shown in Fig.79 with a 13 mm spanner, only after having
loosen the three 13 mm nut on the pole support.
Once optimum position is obtained, tighten firmly all the nuts previously loosen.
16.5.7 ODU grounding
ODU grounding is achieved with:
• M8 screw without washers
• M6 screw with washer
as shown in Fig.80.
In further page are explained all the mounting step not already discussed in paragraph “16.5 1+0 MOUNT-
ING PROCEDURES”.
16.6.1 Installation of Hybrid
Fig.81 – The polarization disk must be always fixed on hybrid flange. Apply silicon grease (e.g. RHODOSIL
PATE 4”) on the O–rings by protecting fingers with gloves. Bring the polarization twist disk with the position
marker down. Insert the O–ring into polarization twist disk.
Vertical polarization: fix the twist disk on hybrid flange placing the marker of the disk towards V mark.
Horizontal polarization: fix the twist disk on hybrid flange placing the marker of the disk towards H mark.
shown in Fig.82.
Tighten progressively and alternatively the screws and the spring washer with following torque:
Fig.83 – Fix hybrid body to 1+0 support with four M8 bolts (use 13 mm spanner, torque = 18 Nm), tighten
progressively and alternatively the bolts.
126
16.6.2 Installation of ODUs (on hybrid for 1+1 version)
For both ODUs.
Fig.75 – Apply silicon grease e.g. RHODOSIL PATE 4” to the O–ring by protecting fingers with gloves.
the support and align the wave guide of the ODU to the wave guide of the hybrid: respect to the position
of wave guide alignment, turn the ODU body approx. 30° counter–clockwise and then insert the ODU body
into the support. For 1+1 system the handle of the ODU is always positioned on the right. The polarization
twist disk on the hybrid matches the antenna polarization.
Fig.84 – When alignment of the reference teeth is achieved, turn the ODU body clockwise until the rotation
stops. In figure are shown ODUs final position.
Fig.77 – When ODU positioning is over, secure ODU body on the support by tightening bolts (use 17 mm
spanner, torque = 6 Nm).
WARNING: Internal codes (e.g. installation items, antennas, PCB) are here reported only as example. The
Manufacturer reserves the right to change them without any previous advice.
Four 13mm
screws
Centring ring
(not present in V32309)
Three 3mm Allen screws Antenna

(not present in V32309)
1+0 support
Two bushes
Fig.74 - 1+0 pole mounting

127
Reference tooth
O-ring
ODU wave guide
"N"
"BNC"
Ground bolt
Vertical Horizontal
Fig.76 - Position of the ODU handle depending on the polarisation for 1+0. For 1+1 the polari-
128
3
1
1
5
4 4
1
2
3
1 6 mm Allen screw
2 Bush (diagonally placed)

3 17 mm Tightening bolts (max torque = 6 Nm)
4 Reference point for horizontal polarization
5 Reference point for vertical polarization
Fig.77 - 1+0 support

129
1+0 ODU HP with handle on the right:
horizontal polarization
1+0 ODU standard with handle on the left:

vertical polarization
Fig.78 - ODU housing final position for both polarization
130
Horizontal aiming:
two 17mm block screws
Vertical aiming:
13mm block screws
Pole support
17mm nut for horizontal

adjustment of antenna
Internal 5mm Allen

screw for vertical
adjustment of antenna
Fig.79 - Antenna aiming

131
1
2
3
4
5
ASN version
AS version
1 Bolt
2 Spring washer
3 Flat washer
5 Flat washer
132
7
2
4
6
1 O–ring
6 O–ring
7 Allen screws
8 Spring washer
Fig.81 - Hybrid and twist disk

133
Fig.82 - Polarization disk fixing (only for 13 GHz and 15 GHz)
134
Fig.83 - Hybrid installation

135
ASN version
AS version
Fig.84 - 1+1 ODUs installation
136
137
WITH RFS INTEGRATED ANTENNA
17.1 FOREWORD
The installation onto the pole of the ODU with integrated antenna concerns both 1+0 and 1+1 version.
Following installation kits are supplied with the equipment depending on different versions.
1+0 version

- 1+0 ODU support and relevant screws

1+1 version
- 1+0 ODU support
- hybrid and relevant screws
- polarization twist disk and relevant screws
- 2 ODUs with O–rings and devices for ground connection.
• N.1 2.5 mm Allen wrench

138
• N.1 13 mm spanner
• N.2 17 mm spanner.
Installation procedure is listed below:
1+0 version

6 antenna aiming
7 ODU grounding
1+1 version
5 installation of hybrid
6 installation of ODUs
7 antenna aiming
8 ODU grounding.
17.5.1 Setting antenna polarization
Fig.74 – Set the antenna in such a position to operate on its rear side. Locate the four M3 Allen screws
around the antenna flange. Unscrew them (use 2.5 mm Allen wrench) and position the antenna flange ac-
cording on: horizontal wave guide –> vertical polarization, vertical wave guide –> horizontal polariza-
tion. Screw again the four Allen screws (torque = 1 Nm).

139
17.5.2 Installation of the centring ring on the antenna
Fig.74 – Set the antenna in such a position to operate on its rear side. Locate the three holes around the
antenna flange. Mount the centring ring onto antenna flange and tight it with the 3 Allen screws M4 (use
3mm Allen wrench, torque 2 = Nm).
17.5.3 Installation of 1+0 ODU support
Fig.74 – Mount the support onto assembled structure (pole support system plus antenna) using the four
M8 Allen screws (use 6 mm Allen wrench, torque 18 = Nm). Two of the four screws, diagonally opposed,
must be mounted with the two bushes around.
17.5.4 Installation onto the pole of the assembled structure
Fig.74 – Mount the assembled structure on the pole using the two pole fixing brackets and the four M10
screws (use 17 mm spanner, torque = 13 Nm); the heads of the screws are inserted on the antenna side,
the four nuts and the springs between nut and brackets are inserted on bracket side.
17.5.5 Installation of ODU (on 1+0 support)
Fig.75 – Apply silicon grease (e.g. RHODOSIL PATE 4”) on the O–ring by protecting fingers with gloves.
the support and align the wave guide of the ODU to the Wave guide of the antenna: respect to the position
of wave guide alignment, turn the ODU body approx. 30° counter–clockwise into the support and search
for matching between reference tooth on the support (see Fig.77) and reference tooth on the ODU body.
Fig.78 – When alignment of the references teeth is achieved, turn the ODU body clockwise until rotation is
stopped. In figure are shown ODU final position for both polarizations.
Fig.77 – When ODU positioning is over, secure ODU body on the support by tightening bolts (use 13mm
spanner, torque = 6Nm).
17.5.6 Antenna aiming
Antenna aiming procedure for 1+0 version or 1+1 version is the same.
Horizontal aiming: ±5° operating on the 17 mm nut shown in Fig.79 with a 17 mm spanner, only after
having loosen the two 17 mm nut on the pivot.
Vertical aiming: ±20° operating on the 13 mm nut shown in Fig.79 with a 13 mm spanner, only after having
loosen the three 13 mm nut on the pole support.
Once optimum position is obtained, tighten firmly all the nuts previously loosen.
140
17.5.7 ODU grounding
ODU grounding is achieved with:
• M8 screw without washers
• M6 screw with washer
as shown in Fig.80.
In further page are explained all the mounting step not already discussed in paragraph “16.5 1+0 MOUNT-
ING PROCEDURES”.
17.6.1 Installation of Hybrid
Fig.81 – The polarization disk must be always fixed on hybrid flange. Apply silicon grease (e.g. RHODOSIL
PATE 4”) on the O–rings by protecting fingers with gloves. Bring the polarization twist disk with the position
marker down. Insert the O–ring into polarization twist disk.
Vertical polarization: fix the twist disk on hybrid flange placing the marker of the disk towards V mark.
Horizontal polarization: fix the twist disk on hybrid flange placing the marker of the disk towards H mark.
shown in Fig.82.
Tighten progressively and alternatively the screws and the spring washer with following torque:
Fig.83 – Fix hybrid body to 1+0 support with four M8 bolts (use 13 mm spanner, torque = 18 Nm), tighten
progressively and alternatively the bolts.
17.6.2 Installation of ODUs (on hybrid for 1+1 version)
For both ODUs.

Fig.75 – Apply silicon grease e.g. RHODOSIL PATE 4” to the O–ring by protecting fingers with gloves.
the support and align the wave guide of the ODU to the wave guide of the hybrid: respect to the position
of wave guide alignment, turn the ODU body approx. 30° counter–clockwise and then insert the ODU body
into the support. For 1+1 system the handle of the ODU is always positioned on the right. The polarization
twist disk on the hybrid matches the antenna polarization.
Fig.84 – When alignment of the reference teeth is achieved, turn the ODU body clockwise until the rotation
stops. In figure are shown ODUs final position.

141
Fig.77 – When ODU positioning is over, secure ODU body on the support by tightening bolts (use 17 mm
spanner, torque = 6 Nm).
WARNING: Internal codes (e.g. installation items, antennas, PCB) are here reported only as example. The
Manufacturer reserves the right to change them without any previous advice.
Three 3 mm
Centering ring Allen screws
Antenna Four 13mm screws
1+0 support
Fig.85 - 1+0 pole mounting
142
Reference tooth
O-ring
ODU wave guide
"N"
"BNC"
Ground bolt
Vertical Horizontal
Fig.87 - Position of the ODU handle depending on the polarisation for 1+0. For 1+1 the polari-

143
2
1
1
4
3 3
1
1 6 mm Allen screw M10
2 17 mm Tightening bolts (max torque = 6 Nm)
3 Reference point for horizontal polarization
4 Reference point for vertical polarization
Fig.88 - 1+0 support
144
1+0 ODU with handle on the left:
vertical polarization
1+0 ODU with handle on the right:

horizontal polarization
Fig.89 - ODU housing final position for both polarization

145
Pole support
Vertical aiming
2
1
Horizontal aiming
Fig.90 - Antenna aiming
146
1
2
3
4
5
ASN version
AS version
1 Bolt
2 Spring washer
3 Flat washer
5 Flat washer

147
7
2
4
6
1 O–ring
6 O–ring
7 Allen screws
8 Spring washer
Fig.92 - Hybrid and twist disk
148
Fig.93 - Polarization disk fixing (only for 13 GHz and 15 GHz)

149
Fig.94 - Hybrid installation
150
AS version
ASN version
Fig.95 - 1+1 ODUs installation

151
152
Section 4.
LINE-UP
18 LINE–UP OF THE RADIO HOP
18.1 LINE–UP OF THE RADIO HOP
The line–up consists of the following steps:

• on site radio terminal installation (user connections and ODU installation as described in the rele-
vant chapters)
• equipment switch–on
• equipment configuration (through PC software)
• antenna alignment for maximum received RF signal level
• network element configuration
• check measurements.
Equipment installation is described in Section 3. INSTALLATION.
18.1.1 Equipment configuration
In order to have the link working properly, in the local and remote equipment the same parameters have
to be set:
• system layout (1+0, 1+1 hot stand-by, 1+1 frequency diversity.....) (Equipment - Configuration)
• ACM Engine (Equipment - Modulation&Capacity)
• Bandwidth&Modulation (Equipment - Modulation&Capacity)
• link ID (Equipment - General)
• RF channel (Equipment-Radio-Radio Branch1A/2A-Tx Frequency Selector)

153
The software to run is Web LCT Console and Web LCT on Internet Explorer with Flash player.
You can download Web Lct Console program and Flash Player from http://www.siaemic.com.
Traffic (Baseband - Tributary)
Used tributaries must be enabled on local and on remote equipment.
18.1.2 Antenna alignment and received field measurement
Purpose of antenna alignment is to maximize the RF received signal level.
Proceed as follows:
• connect a multimeter to BNC connector on the ODU for AGC measurement

• adjust antenna pointing as soon as the maximum AGC voltage value is achieved.
The relationship between AGC voltage and received field is shown by Fig.96.
The received field level has a tolerance of ±4 dB in the full temperature range.
18.1.3 Network element configuration
A factory default address is assigned to each network element that must normally be reconfigurated on
site following the network administrator rules.
For this purpose it is required to connect the PC, where the WLC program has been installed, to the network
interfaces.
This has to be done via USB cable or Ethernet cable.
Warning: the checks that follow require a good knowledge of the program use.
Run the program and perform the connection to equipment by choosing from menu “Option” the connec-
tion made via USB cable.
Perform the login to the equipment by entering:
• Equipment IP address 3
• User ID (default: SYSTEM)
• Password: (default: siaemicr)

Proceed to program what above mentioned following this path:
• IP Address: select Port Configuration. Enter the required port addresses in the available communi-
cation ports.
• Routing Table and Default Gateway: select Routing table: add the routes and default gateway if nec-
essary.
Warning: the routing policy depends on the routing type: static IP/OSPF/IS–IS. The relevant rout-
ing rules must be normally given by network administrator.
• Remote Element Table: select Remote Element Table. Add station name. Add local equipment IPad-
dress, add remote equipment IP address selecting Remote Link.
• Agent IP Address: select Equipment Properties. Assign the address in accordance to the address of
Ethernet port.
3 If the connection is made via USB cable, the IP address is automatically achieved.
154
18.1.4 Radio checks
It is advisable to perform the following measurements to check the correct operation of the radio hop:
• transmitted power
• received power
• RF frequency
• BER measurement
All these checks make use of the WLC program.
• Transmitted power, received RF level, RF frequency

- run WLC program and then perform the connection to the equipment you want to check.
- on top of the window Tx/Rx power and frequency values are displayed. In case of Tx power and
frequency setup proceed to Branch 1/2 and Power/Frequencies submenus.
• BER measurement
- Run WLC program and then perform the connection to the equipment you want to check.
- On the left side select BER1/2 measure.

In alternative it is possible to use the PRBS function if one or 2 Mbit/s line is free.
- Perform the BER measurement and check that values comply with the requirements.
2,625
2,25
1,875
1,5
1,125
0,75
0 dBm
-100 -80 -70 -60 -50 -40 -30 -20
Fig.96 - Detected voltage versus RF received signal

155
19 BACK UP FULL EQUIPMENT CONFIGURATION
WITHOUT POSSIBILITY OF MODIFYING THE PA-
RAMETERS
19.1 SCOPE
This chapter describes the procedure to back up the full equipment configuration. This permits to recover
the original equipment configuration in case of faulty CONTROLLER module replacement with spare.
19.2 CONFIGURATION UPLOAD
Foreword: it is advisable to upload the configuration during the first installation. Proceed as follows:
1 Select “Equipment Configuration Wizard” from menu “Tools”; “Equipment Configuration Wiz-
ard” window will be displayed.
2 Select “Upload” and then “Backup Full Equipment Configuration”; “Template Selection” win-
dow will be displayed.
3 Select the correct equipment template (in case of uncorrected choice the backup will be aborted).
4 Press OK and then select the equipment to be uploaded from “Upload Configuration File” window.
5 Press OK and then edit the file name from “Save backup as” window.
6 Press Save; “Equipment Configuration Wizard: Complete Backup” window will appear.
The window shows dynamically the backup procedure. If everything is OK, at the end of the upload
will appear the word “done” showing the procedure success.
7 Press OK to finish.
19.3 CONFIGURATION DOWNLOAD
Once the spare LIM has been installed proceed as follows:
1 Select “Equipment Configuration Wizard” from menu “Tools”. “Equipment Configuration Wizard”
window will be displayed.
2 Select “Download” and than “Restore Full Equipment Configuration” from Equipment Config-
uration Wizard. “Select Backup File” window will be displayed.
3 Select the wanted backup file with extension .bku and then press Open. “Download Configuration
File” window will be displayed.
4 Select the equipment to download and then press OK; “Equipment Configuration Wizard: Complete
restore” window will be displayed. This window shows dynamically the download operation. The
word “done” indicates that download has been successfully.
5 Press OK to finish.
Warning: In case of EOC alarm proceed to restart the equipment.
156
20 LINE-UP FOR ETHERNET TRAFFIC
20.1 GENERAL
This paragraph deals with line-up of LIM Ethernet module with details of WebLCT program related only to
Ethernet application.
Assuming that the radio link is already in service, with correct frequency, output power and correct antenna
alignment, the line up procedure for two different kinds of connection set up of a radio link ALplus2,
equipped with LIM module with Ethernet ports, is hereafter described:
• Local Lan-1 port to remote Lan-1 port connection Lan per port, see Fig.97
• from 3 ports to 3 ports connections and segregated traffic for Untagged Traffic, see Fig.105
• from 3 ports to 3 ports connections and segregated traffic for Tagged and Untagged Traffic, see
Fig.115.
Settings here below are intended to be done both into local and remote radio equipment. The software to
be used to configure the equipment is WEB LCT. In the following chapters all configuration steps are shown
using WEB LCT.
20.2 LOCAL LAN-1 PORT TO REMOTE LAN-1 PORT TRANSPARENT

CONNECTION LAN PER PORT
Settings for Untagged and Tagged Traffic
switch switch
Lan-1 port 1 port 1 Lan-1
Lan-2 AL AL Lan-2
radio radio
Lan-3 Lan-3
Nx2 Nx2
Mbit/s Mbit/s
Local Remote
Fig.97 - Local Lan-1 port to remote Lan-1 port connection
The first example is local Lan1 port to remote Lan1 port transparent connection for tagged and untagged
traffic please refer to Fig.97.

157
Fig.98 - Modulation and capacity
Select 1+0 or 1+1 configuration according system requirements.

Please refer to Fig.98. First selection is channel bandwidth and modulation, in this example we selected
28MHz and 16QAM.
ACM Engine, Upper Modulation, Lower Modulation, Permanent Traffic and extra TDM Capacity at any mod-
ulation must be the same local and remote.
The troughput at any modulation with 28 MHz bandwidth is shown in Fig.99 with View Current Config but-
ton of Fig.98.
Fig.99 - View Current Configuration
So with 4QAMstrong modulation the Ethernet capacity is 20 Mbit/s and with 256QAM modulation the Eth-
ernet capacity is 140 Mbit/s.
158
Fig.100 - Switch general settings
See Fig.100 for general settings of the switch. All the used ports must be Enabled, so enable Lan-1 and
Internal Port A, see Fig.101.
Please notice the MAC Address Aging Time reduced, only for this test at 15 sec.
The other ports should be disabled. The correct cable crossover arrangement must be selected too (see
Fig.101). Enable LLF, if needed, only at the end of link line up.
Select Master or Slave Role for 1000BaseT interface.
Switch connections are done with Lan per port selections. Referring to Fig.102, incoming traffic at Lan-1
exits at internal Port A and as in Fig.103 and in Fig.104 incoming traffic at internal Port A exits at Lan-1
port. This connection are done for all Untagged packets and all Tagged packets with Vlan Id not described
into Vlan Configuration Table.
If Vlan Configuration Table is blank all Tagged traffic follows the rules of Lan per port.
Possible selections of Ingress Filtering Check:
• "Disable 802.1q": no check of Virtual Lan tag is done and all packets follow Lan per port settings
• "Fallback": if Tagged packets have their Vlan Id into Vlan Configuration Table they follow the con-
nection described into the table, otherwise they follow the Lan per port settings as Untagged pack-
ets
• "Secure": no Untagged packet transits; only Tagged packets with Vlan Id listed into the table can
transit.
For all previous configuration "Disable 802.1" should be selected. With Egress Mode as Unmodified the out-
going packets at Lan-1 port exit Untagged or Tagged exactly as they were Untagged or Tagged at the in-
coming port.

159
Fig.101 - Lan-1 interface settings
Fig.102- Vlan settings for LAN-1
160
Fig.103 - Vlan settings for Port A
Fig.104 - Priority setting for Lan-1 and Port A

161
20.3 FROM 3 PORT TO 3 PORT CONNECTIONS
Settings for Untagged traffic.
switch switch
Lan-2 AL AL Lan-2
radio radio
Lan-3 Lan-3
Nx2 Nx2
Mbit/s Mbit/s
Local Remote
Fig.105 - 3 ports to 3 ports connections with segregated traffic
In this example 3 local port must communicate with corresponding 3 remote ports. All the ports share the
same radio channel but traffic originated and directed to Lan1 should be kept separated from traffic from
Lan2 and Lan3 and viceversa.
Lan-1 to Lan-1, connection must transfer untagged packets.
Lan-2 and Lan-3 have the same requirements. Please refer to Fig.105.
Fig.106 - Modulation and capacity
28MHz and 16QAM.
ton of Fig.106.
162
See Fig.108 for Switch general settings of the switch. All the used ports must be Enabled, so enable Lan-
1, Lan-2, Lan-3 and Internal Port, see Fig.109.
Please notice the MAC Address Aging Time reduced, only for this test, at 15 sec. The correct cable crossover
arrangement must be selected too (see Fig.109). Enable LLF if needed only at the end of link line up.
Select Master or Slave Role for 1000BaseT interface.
For Untagged traffic, connections are done with Lan per port selections. Referring to Fig.110 incoming traf-
fic at Lan-1 exits at internal Port A and into Fig.113 incoming traffic at internal Port A exits at Lan-1 port.

163
This connection are done for all Untagged traffic and all Tagged packets with Vlan Id not described into
Vlan Configuration Table.
If Vlan Configuration Table is blank all Tagged traffic follows the rules of Lan per port.
Possible selections of Ingress Filtering Check:
• "Disable 802.1q": no check of Virtual Lan tag is made and all packets follow Lan per port settings
• "Fallback": if Tagged packets have their Vlan Id into Vlan Configuration Table they follow the con-
nection described into the table, otherwise they follow the Lan per port settings as Untagged pack-
ets
• "Secure": no Untagged packet transits; only Tagged packets with Vlan Id listed into the table can
transit.
Fig.109 - Lan-1 interface settings
All the used ports must be Enabled.

The correct Cable Crossover arrangement must be selected too.
Untagged traffic transits only if the selection for Ingress Filtering Check is disabled at each input port and
a separated Vlan for Untagged traffic is set up for each port.
Each port of the switch must be associated with a different Default VLAN ID, Lan-1 with Default VID 4001,
Lan-2 with Default VID 4002, Lan-3 with Default VID 4003, for Lan-1 see Fig.109 and Fig.110.
Untagged packets coming at physical ports are tagged on common radio channel but tagged with different
Vlans. At receiving end packets are distributed at their ports and untagged.
Vlan Configuration Table will be defined in order to group traffic from Lan-1, Lan-2, Lan-3 to Port A.
The Vlan Configuration Table must be programmed as in Fig.114.
164
Fig.110 - Lan1 Vlan settings

165
Fig.113 - Port A Vlan settings
166
Fig.114 - Vlan Configuration Table
20.4 FROM 3 PORT TO 3 PORT CONNECTIONS
Settings for Tagged Traffic, QinQ
switch switch
Lan-2 AL AL Lan-2
radio radio
Lan-3 Lan-3
Nx2 Nx2
Mbit/s Mbit/s
Local Remote
Fig.115 - 3 ports to3 ports connections with segregated Tagged and Untagged traffic
In this example 3 local port must communicate with corresponding 3 remote ports. All the ports share the
same radio channel but traffic originated and directed to Lan1 should be kept separated from traffic from
Lan2 and Lan3 and viceversa.
Lan-1 to Lan-1, connection must transfer tagged and untagged packets. Lan-2 and Lan-3 have the same
requirements. Please refer to Fig.115.

167
Fig.116 -Modulation and Capacity
28MHz and 16QAM.
ton of Fig.116.
168
See Fig.118 for Switch general settings of the switch. All the used ports must be Enabled, so enable Lan-
1, Lan-2, Lan-3 and internal Port A, see Fig.101.
For already Tagged traffic we need to add a second Vlan Tag to the packets creating the Vlan of Vlan into
radio channel, so we need a Max packet size of 2048.
Settings are as reported in Fig.119, Fig.120, Fig.121, Fig.122, Fig.123.

169
170
Fig.122 - Port A Vlan settings
Fig.123 - Vlan Configuration Table

171
21 HOW TO CHANGE ADDRESS ON REMOTE EQUIP-
MENT WITHOUT LOSING THE CONNECTION
21.1 TOOLS
The following procedure can be done with SCT/LCT or with Web LCT and similar windows.
21.2 PROCEDURE
1 Set new addresses on remote equipment

2 Clear the Stored Routing Table on remote equipment and add new lines to it
3 Set the new Agent and restart remote equipment
4 Configure Local equipment

5 Prepare Subnetwork on local equipment, capture the remote equipment and send it the new sub-
netork
Select the remote equipment
Select menu Equipment -> Configuration Setup -> Port Configuration
172
Fig.124 - Subnetwork Craft Terminal - Communication setup
Configuration
Configure:
IP Ethernet ->Ip address and netmask (see Fig.125)
Lct PPP -> Ip address and netmask (see Fig.126)
PPP Radio -> Ip address and netmask (see Fig.127)
If you have other port to configure ex. PPP RS232 - 2Mbit/s EOC ecc. configure it with IP and netmask

173
Fig.125 - IP Ethernet
Fig.126 - LCT PPP
174
Fig.127 - PPP Radio
At the end select Set Values -> Confirm and Store -> Confirm.

175
Select the equipment
Select menu Equipment -> Configuration Setup -> Stored Routing Table
Fig.128 - Store Routing Table
In this menu delete all lines and default gateway, push Apply and then Save.
176
Fig.129 - Stored Routing Table
Add new routine lines (relevant the new addresses configuration) pushing the Add button.
When the Stored Routing Table is complete, push Apply and then Save.
Select the remote equipment
Select menu Equipment -> Properties. Set new Agent (equal to Ethernet port address).
Push Restart and then Confirm.
After the restart, the Remote Equipment disappears from SCT display.
Configure the local equipment
Configure the local equipment with the same procedure seen before. Then restart the local equipment.
Subnetwork Configuration Wizard
To see both local and remote equipment the new subnetwork (station and equipment) must be prepared.
Select menu Tools -> Subnetwork Configuration Wizard.

177
Fig.130 - Subnetwork Configuration Wizard
178
Fig.131 - Subnetwork Configuration Wizard - Actual Configuration
Push Add Station, write its name and push OK.

179
Fig.132 - Add new station
Select this new station and push Add Element.
The Ip Address to set is the Agent (equal to Ethernet port address).
180
Fig.133 - Add New Network Element
After having set the Equipment Address, push OK.
The new element is created inside the previously created station
This step must be done for local and remote equipment.

181
Select the local equipment (the one with System (Local))
182
Send the configuration to local equipment.
When the remote equipment appears in Actual Configuration, prepare again the network configuration you
have set before (or select the local equipment, push Retrieve) and send the configuration to remote equip-
ment.

183
184
Section 5.
PROGRAMMING AND SUPERVI-
SION
22 PROGRAMMING AND SUPERVISION
22.1 GENERAL
The radio equipment was designed to be easily programmed and supervised.
The following tools are implemented to the purpose:

• SCT Subnetwork Craft Terminal + WEB LCT Local Craft Terminal. They are used for remote and local
control of a subnetwork consisted of a maximum of 100 AL radio equipment.
• NMS5–UX Network Management. It is used for the remote control of an entire network consisted of
different SIAE equipment including radio equipment.
For details refer to relevant documentation. SCT/LCT documentation is available as help on–line.
22.2 WEBLCT
Equipment can be locally controlled by an embedded Web Server, the WEB LCT, and an http browser run-
ning on PC.
It is also available a software named SCT that can manage sub networks of SIAE Network Elements.
The hardware platform used by SCT is based on Personal Computer with at least the following character-
istics:
• HD with 100 Mbyte of free space

• Windows XP/Windows Vista
• Flash Player version 8.1 or higher

185
Fault Management
The operator can check the status the equipment through an "Alarm Display Panel" that is automatically
updated by the system.
Alarm records are stored by the equipment in an history log together with all information which could be
of interest for the user, among which:
• event occurrence date and time
• equipment type and address
• unit identification information
• alarm description
• event severity level
The operator can access the history log using different filters.
Equipment Configuration
The configuration parameters the operator can update from the WebLCT are:
• System type (protected or not protected)
• Channel bandwidth
• ACM profiles
• RF channel
• ATPC enable/disable
• ATPC Rx thresholds
• RTPC
• Rx power alarm threshold

• Tributary port enable/disable
• STM-1, VC4 and VC12 parameters
• E1 cross connection matrix

• Ethernet switch parameters
• Synchronisation parameters
• Alarm enable
• Alarm severity
• User inputs and relay configuration
• TMN port configuration
Equipment Maintenance
The main maintenance parameters that the operator can update from the WebLCT are:
• transmitter enable/disable
• carrier only
• loops4 (see Fig.136)
• active state forcing in 1+1 configuration
• PRBS
The following figure shows the loops that can be set from the WEBLCT, for any IDU configuration.
4 Line loops can be done for E1, STM-1 and Ethernet interfaces. Internal loops can be done for E1 and
STM-1 interfaces.
186
Internal
loop (2)
IDU ODU
Line IDU ODU

loop (1) loop (3) loop (4)
1. Line tributary loop

2. Internal tributary loop
3. IDU loop
4. RF loop
Fig.136 - Loop
Software management
A new firmware or a new WEBLCT release can be downloaded from the WEBLCT itself. Actual software re-
lease is reported to the operator.
Performance management
G828, Rx Power, Tx Power and ACM counters are calculated both on radio side and line side
All counters are available on 15 minutes basis and daily, the WEBLCT collects 16 blocks of 15 minutes
counters showing in this way the history of 4 hours.
The user can Start and Stop the Performance Monitoring function.
The user can define a threshold for each counter, when the threshold is crossed an alarm is set by the
equipment, the performance alarm severity can be set by the operator.
Fig.137 reports all the Termination points for the performance monitoring supported by ALplus2.
G828 Radio 1
G828 - 2 Mbit/s Rx&Tx
radio side Power Radio 1
ODU1
G828 - B1 STM-1
G.829 B2 & M1 STM-1 IDU
Line side
Rx&Tx
G828 - 2 Mbit/s ODU2 Power Radio 2
line side
G828 Radio 2
Fig.137 - Termination points for the Performance Monitoring

187
In addition to what shown in the figure above, the following performance monitoring features are available:
• RMON for Ethernet port statistics, both on tributary and radio side
• ACM performance monitoring counters
Security Management
The WEBLCT Administrator creates and manages a set of user accounts, the security information (Pass-
word and User profile) is used for identification, authentication purpose.
Two operator levels are enabled depending on the profile assigned to the operator:
• full privilege level allows the operator to perform all the available options.
• partial privilege level allows the operator to read alarm and configuration parameters and mainte-
nance commands (e.g. force switch over in 1+1 systems).
188
Section 6.
COMPOSITION
23 COMPOSITION OF MODULAR IDU
23.1 GENERAL
The ALplus2 IDU is available in following versions:

• 1RU 1+0 unduplicated
• 1RU 1+1 standard.
Both units consist of plug-in modules as LIM/RIM/Controller that can individually be replaced.
Module part number, hardware layout and equipment composition are subject to change without notice.
23.2 IDU PART NUMBER
Every version is identified by a specific part number shown on a label (see Fig.140) attached on IDU, top
left side. Important power supply informations are also written.
The P/N consists of seven digits with the following meaning:

189
Tab.33- IDU part number
Digit Letter/number Meaning
Functional assembly of units completed by a mechanical

1 G
structure
2 A AL equipment
3 I Indoor installation
0165 1+0 - 1 unit - 16E1 + 2xSTM1 + FE

4 to 7
0166 1+1 - 1 unit - 16E1 + 2xSTM1 + FE
23.3 COMPOSITION OF THE INDOOR UNIT
1+0/1+1 standard, Ethernet version
The IDU consists of LIM/RIM/CONTROLLER modules. Each module is identified through internal label indi-
cating the relevant P/N.
The P/Ns are the following:
- LIM
- RIM
- CONTROLLER.
1 2 3 ON 48V
SPEED
PoE
ACT FAIL
LINK
+

-
LINK LINK IDU ODU
ACT ACT WAY
SIDE
REM TEST
Fig.138 - IDU GAI0165
1 2 3 ON 48V
SPEED
PoE
ACT FAIL
LINK
+

-
LINK LINK IDU ODU 48V
ACT ACT WAY
SIDE
+
REM TEST
-
Fig.139 - IDU GAI0166
190
Fig.140 - IDU P/N

191
24 COMPOSITION OF OUTDOOR UNIT
24.1 GENERAL
The ODU consists of a mechanical structure that houses all the transceiver circuitry. In 1+1 HSB version
the connection to the antenna is performed through a passive hybrid.
Both transceiver and hybrid are offered in different versions depending on the operating bands, the anten-
na configuration etc...
A label (see Fig.141) attached on the ODU structure shows the most significant parameters as go/return
frequency value, subband, operating band and part number.
Part number identifies the ODU type. ODU description in the following tables shows frequency, go-return,
channel and capacity if specified.
For example:
• ODU AS 11/530 ITU CH9L 2xSTM1 means:

ODU 11 GHz band frequency, 530 MHz go-return, CH9 Low fixed preset, 2xSTM1 capacity
• ODU AS 23/1008 SB 2H means:
ODU 23 GHz band frequency, 1008 MHz go-return, 2 high subband.
In Tab.34 and Tab.35 various ODU versions and hybrid part number are listed.
Part number, hardware layout and equipment composition are subject to change without notice.
Tab.34 - Part number and description
RF band in GHz ODU description Part number
ODU AS6L CH=1H GE9185
ODU AS6L CH=1H GE9185-03
ODU AS6L CH=1L GE9184
ODU AS6L CH=1L GE9184-03
192
6 ODU AS6L CH=8L GE9198
ODU AS6L SB=1H GE9269
ODU AS6L SB=1H GE9269-03
ODU AS6L SB=1L GE9268
ODU AS6L SB=1L GE9268-03
ODU AS6U CH=1H GE9291

193
ODU AS6U CH=1H GE9291-03
ODU AS6U CH=1L GE9290
ODU AS6U CH=1L GE9290-03
6 ODU AS6U CH=5L GE9298-03
ODU AS6U SB=1H GE9285
ODU AS6U SB=1H GE9285-03
ODU AS6U SB=1L GE9284
ODU AS6U SB=1L GE9284-03
194

6
ODU AS7H/245 SB=1H GE9137
ODU AS7H/245 SB=1H GE9137-03
ODU AS7H/245 SB=1L GE9136
ODU AS7H/245 SB=1L GE9136-03
ODU AS7H/245 SB=2H GE9139-03
ODU AS7H/245 SB=2L GE9138-03
ODU AS7H/245 SB=3H GE9141-03
ODU AS7H/245 SB=3L GE9140-03
ODU AS7L/161 SB=1H GE9253
ODU AS7L/161 SB=1H GE9253-03
7 ODU AS7L/161 SB=1L GE9252
ODU AS7L/161 SB=1L GE9252-03
ODU AS7L/161 SB=2H GE9255-03
ODU AS7L/161 SB=2L GE9254
ODU AS7L/161 SB=2L GE9254-03
ODU AS7L/161 SB=3H GE9257-03
ODU AS7L/161 SB=3L GE9256-03
ODU AS7L/196 SB=1H GE9009-03
ODU AS7L/196 SB=1L GE9008-03

195
ODU AS7L/196 SB=2H GE9011-03
ODU AS7L/196 SB=2L GE9010-03
ODU AS7L/196 SB=3H GE9013-03
ODU AS7L/196 SB=3L GE9012-03
ODU AS7M/154 SB=10H GE9329
ODU AS7M/154 SB=10L GE9328
ODU AS7M/154 SB=10L GE9328-03
ODU AS7M/154 SB=1H GE9173-03
ODU AS7M/154 SB=1L GE9172-03
ODU AS7M/154 SB=2H GE9175-03
ODU AS7M/154 SB=2L GE9174-03
7 ODU AS7M/154 SB=3H GE9177
ODU AS7M/154 SB=3H GE9177-03
ODU AS7M/154 SB=3L GE9176-03
ODU AS7M/154 SB=4H GE9179-03
ODU AS7M/154 SB=4L GE9178-03
ODU AS7M/154 SB=5H GE9181-03
ODU AS7M/154 SB=5L GE9180-03
ODU AS7M/154 SB=7H GE9323-03
ODU AS7M/154 SB=7L GE9322-03
ODU AS7M/154 SB=8H GE9325-03
196
ODU AS7M/154 SB=8L GE9324-03
ODU AS7M/154 SB=9H GE9327-03
ODU AS7M/154 SB=9L GE9326-03
ODU AS7M/161 SB=1H GE9259-03
ODU AS7M/161 SB=1L GE9258-03
ODU AS7M/161 SB=2H GE9261-03
ODU AS7M/161 SB=2L GE9260-03
7 ODU AS7M/161 SB=3H GE9263-03
ODU AS7M/161 SB=3L GE9262-03
ODU AS7M/168 SB=1H GE9015-03
ODU AS7M/168 SB=1L GE9014-03
ODU AS7M/168 SB=2H GE9017-03
ODU AS7M/168 SB=2L GE9016-03
ODU AS7M/168 SB=3H GE9019-03
ODU AS7M/168 SB=3L GE9018-03
ODU AS8/266 SB=1H GE9279
ODU AS8/266 SB=1H GE9279-03
ODU AS8/266 SB=1L GE9278
ODU AS8/266 SB=1L GE9278-03

8
ODU AS8/266 SB=2H GE9281-03
ODU AS8/266 SB=2L GE9280-03

197
ODU AS8/266 SB=3H GE9283-03
ODU AS8/266 SB=3L GE9282-03
ODU AS8/310 SB=1H GE9145-03
ODU AS8/310 SB=1L GE9144-03
ODU AS8/310 SB=2H GE9147-03
ODU AS8/310 SB=2L GE9146-03
ODU AS8/310 SB=3H GE9149-03
ODU AS8/310 SB=3L GE9148-03
ODU AS8/311,32 SB=1H GE9051
ODU AS8/311,32 SB=1H GE9051-01

8
ODU AS8/311,32 SB=1H GE9051-03
ODU AS8/311,32 SB=1L GE9050
ODU AS8/311,32 SB=1L GE9050-01
ODU AS8/311,32 SB=1L GE9050-03
ODU AS8/311,32 SB=2H GE9053
ODU AS8/311,32 SB=2H GE9053-01
ODU AS8/311,32 SB=2H GE9053-03
ODU AS8/311,32 SB=2L GE9052
ODU AS8/311,32 SB=2L GE9052-01
ODU AS8/311,32 SB=2L GE9052-03
ODU AS8/311,32 SB=3H GE9265
ODU AS8/311,32 SB=3H GE9265-03
ODU AS8/311,32 SB=3L GE9264
ODU AS8/311,32 SB=3L GE9264-03
ODU AS8/311,32 SB=4H GE9267
ODU AS8/311,32 SB=4H GE9267-03
ODU AS8/311,32 SB=4L GE9266
ODU AS8/311,32 SB=4L GE9266-03
11 ODU AS11 - G/R490 CH=9H GE9129-03
198
ODU AS11 SB=1H GE9235
ODU AS11 SB=1H GE9235-03
ODU AS11 SB=1L GE9234
ODU AS11 SB=1L GE9234-03
ODU AS11/490 CH=10H GE9131
ODU AS11/490 CH=10L GE9130
ODU AS11/490 CH=11H GE9133
ODU AS11/490 CH=11H GE9133-03
ODU AS11/490 CH=11L GE9132
ODU AS11/490 CH=11L GE9132-03
11 ODU AS11/490 CH=12H GE9135
ODU AS11/490 CH=12L GE9134
ODU AS11/490 CH=1H GE9113
ODU AS11/490 CH=1L GE9112
ODU AS11/490 CH=4H GE9119-03
ODU AS11/490 CH=4L GE9118-03
ODU AS11/490 CH=5H GE9121-03
ODU AS11/490 CH=5L GE9120-03

199
ODU AS11/490 CH=7H GE9125-03
ODU AS11/490 CH=7L GE9124-03
ODU AS11/490 CH=8H GE9127-03
ODU AS11/490 CH=8L GE9126-03
ODU AS11/490 CH=9L GE9128-03
ODU AS11/530 ITU CH=10H GE9229
ODU AS11/530 ITU CH=10L GE9228
11 ODU AS11/530 ITU CH=2H GE9213
ODU AS11/530 ITU CH=3H 2XSTM1 GE9333
ODU AS11/530 ITU CH=3L 2XSTM1 GE9332
200
11 ODU AS11/530 ITU CH=9H 2XSTM1 GE9339
ODU AS13 CH=1H GE9151
ODU AS13 CH=1H GE9151-03
ODU AS13 CH=1L GE9150
ODU AS13 CH=1L GE9150-03

13

201

13
ODU AS15/315 /322 SB=3H GE9205
ODU AS15/315/322 SB=1H GE9201
15 ODU AS15/315/322 SB=1H GE9201-03
ODU AS15/315/322 SB=1L GE9200
ODU AS15/315/322 SB=1L GE9200-03
ODU AS15/315/322 SB=1L GE9207-03
ODU AS15/315/322 SB=2H GE9203
ODU AS15/315/322 SB=2H GE9203-03
ODU AS15/315/322 SB=2L GE9202
ODU AS15/315/322 SB=2L GE9202-03
ODU AS15/315/322 SB=3H GE9205-03
ODU AS15/315/322 SB=3L GE9204
ODU AS15/315/322 SB=3L GE9204-03
202
ODU AS15/315/322 SB=4H GE9207
ODU AS15/315/322 SB=4L GE9206
ODU AS15/315/322 SB=4L GE9206-03
ODU AS15/315/322 SB=5H GE9209
ODU AS15/315/322 SB=5H GE9209-03
ODU AS15/315/322 SB=5L GE9208
ODU AS15/315/322 SB=5L GE9208-03
ODU AS15/420 SB=1H GE9027-03
ODU AS15/420 SB=1L GE9026-03
ODU AS15/420 SB=2H GE9029-03
ODU AS15/420 SB=2L GE9028-03
ODU AS15/420 SB=3H GE9031-03
15 ODU AS15/420 SB=3L GE9030-03
ODU AS15/420 SB=4H GE9033-03
ODU AS15/420 SB=4L GE9032-03
ODU AS15/490 SB=1H GE9035-03
ODU AS15/490 SB=1L GE9034-03
ODU AS15/490 SB=2H GE9037-03
ODU AS15/490 SB=2L GE9036-03
ODU AS15/490 SB=3H GE9039-03
ODU AS15/490 SB=3L GE9038-03
ODU AS15/490 SB=4H GE9041-03

203
ODU AS15/490 SB=4L GE9040-03
ODU AS15/644 SB=1H GE9313-03
ODU AS15/644 SB=1L GE9312-03
ODU AS15/644 SB=2H GE9315-03
ODU AS15/644 SB=2L GE9314-03
ODU AS15/728 CH=1H GE9105-03

15
ODU AS15/728 CH=1L GE9104-03
ODU AS15/728 CH=2H GE9107-03
ODU AS15/728 CH=2L GE9106-03
ODU AS15/728 CH=3H GE9109-03
ODU AS15/728 CH=3L GE9108-03
ODU AS15/728 CH=4H GE9111-03
ODU AS15/728 CH=4L GE9110-03
ODU AS15/728 SB=1H GE9047-03
ODU AS15/728 SB=1L GE9046-03
18 ODU AS18 CH=13L GE9078
204
18 ODU AS18 CH=9L GE9070
ODU AS18/1010 CH=10H GE9073-03
ODU AS18/1010 CH=10L GE9072-03
ODU AS18/1010 CH=11H GE9075-03
ODU AS18/1010 CH=11L GE9074-03
ODU AS18/1010 CH=12H GE9077-03
ODU AS18/1010 CH=12L GE9076-03
ODU AS18/1010 CH=13H GE9079-03
ODU AS18/1010 CH=13L GE9078-03
ODU AS18/1010 CH=14H GE9081-03
ODU AS18/1010 CH=14L GE9080-03

205
ODU AS18/1010 CH=15H GE9083-03
ODU AS18/1010 CH=15L GE9082-03
ODU AS18/1010 CH=16H GE9085-03
ODU AS18/1010 CH=16L GE9084-03
ODU AS18/1010 CH=17H GE9087-03
ODU AS18/1010 CH=17L GE9086-03
ODU AS18/1010 CH=1H GE9055-03
ODU AS18/1010 CH=1L GE9054-03
ODU AS18/1010 CH=2H GE9057-03
ODU AS18/1010 CH=2L GE9056-03
ODU AS18/1010 CH=3H GE9059-03
ODU AS18/1010 CH=3L GE9058-03
ODU AS18/1010 CH=4H GE9061-03
ODU AS18/1010 CH=4L GE9060-03
ODU AS18/1010 CH=5H GE9063-03
ODU AS18/1010 CH=5L GE9062-03
ODU AS18/1010 CH=6H GE9065-03
ODU AS18/1010 CH=6L GE9064-03

18
ODU AS18/1010 CH=7H GE9067-03
ODU AS18/1010 CH=7L GE9066-03
ODU AS18/1010 CH=8H GE9069-03
ODU AS18/1010 CH=8L GE9068-03
ODU AS18/1010 CH=9H GE9071-03
ODU AS18/1010 CH=9L GE9070-03
ODU AS18/1010 SB=1H GE9001-03
ODU AS18/1010 SB=1L GE9000-03
ODU AS18/1010 SB=2H GE9003-03
ODU AS18/1010 SB=2L GE9002-03
ODU AS18/1010 SB=3H GE9005-03
ODU AS18/1010 SB=3L GE9004-03
ODU AS18/1010 SB=4H GE9007-03
ODU AS18/1010 SB=4L GE9006-03
ODU AS18/1560 SB=1H GE9183
ODU AS18/1560 SB=1H GE9183-03
ODU AS18/1560 SB=1L GE9182
ODU AS18/1560 SB=1L GE9182-03
23 ODU AS23/1008 SB=1H GE9171
206
ODU AS23/1008 SB=1H GE9171-03
ODU AS23/1008 SB=1L GE9170
ODU AS23/1008 SB=1L GE9170-03
ODU AS23/1008 SB=2H GE9049
ODU AS23/1008 SB=2H GE9049-03
ODU AS23/1008 SB=2L GE9048
ODU AS23/1008 SB=2L GE9048-03
ODU AS23/1200-1232 SB=1H GE9241
ODU AS23/1200-1232 SB=1H GE9241-03
23 ODU AS23/1200-1232 SB=1L GE9240
ODU AS23/1200-1232 SB=1L GE9240-03
ODU AS23/1200-1232 SB=2H GE9243
ODU AS23/1200-1232 SB=2H GE9243-03
ODU AS23/1200-1232 SB=2L GE9242
ODU AS23/1200-1232 SB=2L GE9242-03
ODU AS23/1200-1232 SB=3H GE9245
ODU AS23/1200-1232 SB=3H GE9245-03
ODU AS23/1200-1232 SB=3L GE9244
ODU AS23/1200-1232 SB=3L GE9244-03

25

32

207

32

38
Tab.35 - ODU ASN part number and description
ODU ASN6L SB=1H GE9501
ODU ASN6L SB=1L GE9500

6
ODU ASN6U SB=1H GE9509
ODU ASN6U SB=1L GE9508
ODU ASN7L/161 SB=1H GE9519
ODU ASN7L/161 SB=1L GE9518
7 ODU ASN7L/161 SB=3H GE9523
208
ODU ASN7M/154 SB=1H GE9535
ODU ASN7M/154 SB=1L GE9534
7 ODU ASN7M/154 SB=4H GE9541
ODU ASN8/311,32 SB=1H GE9583
ODU ASN8/311,32 SB=1L GE9582
ODU ASN8/311,32 SB=2H GE9585
ODU ASN8/311,32 SB=2L GE9584

8
ODU ASN8/311,32 SB=3H GE9587
ODU ASN8/311,32 SB=3L GE9586
ODU ASN8/311,32 SB=4H GE9589
ODU ASN8/311,32 SB=4L GE9588
ODU ASN10/350 SB=1H GE9601

10
ODU ASN10/350 SB=1L GE9600
ODU ASN13 SB=1H GE9613
ODU ASN13 SB=1L GE9612

13

209
ODU ASN15 315/322 SB=1H GE9629
ODU ASN15 315/322 SB=1L GE9628

15

18
ODU ASN23/1200/1232 SB=1H GE9727

23
ODU ASN23/1200/1232 SB=1L GE9726
ODU ASN23/1200/1232 SB=2H GE9729
ODU ASN23/1200/1232 SB=2L GE9728
ODU ASN23/1200/1232 SB=3H GE9731
ODU ASN23/1200/1232 SB=3L GE9730

25
210
Fig.141 - Label attached on the ODU mechanical body AL

211
212
Section 7.
LISTS AND SERVICES
25 LIST OF FIGURES
Fig.1 - Components electrostatic charge sensitive indication................................................ 10
Fig.2 - Elasticized band .................................................................................................. 10

Fig.3 - Coiled cord ......................................................................................................... 10
Fig.4 - Laser indication................................................................................................... 10
Fig.5 - WEEE symbol - 2002/96/CE EN50419 .................................................................... 11

Fig.6 - ALplus2 1+0 ....................................................................................................... 20
Fig.7 - ALplus2 1+1 ....................................................................................................... 21
Fig.8 - ALCplus2 1+0 ..................................................................................................... 21
Fig.9 - ALCplus2 1+1 ..................................................................................................... 21
Fig.10 - ALCplus2 1+0 exp 16E1 ..................................................................................... 21
Fig.11 - ALCplus2 1+1 exp 16E1 ..................................................................................... 21

Fig.12 - ALCplus2 1+0 32E1 ........................................................................................... 21
Fig.13 - ALCplus2 1+1 32E1 ........................................................................................... 21
Fig.14 - ALCplus2 1+0 exp nodal..................................................................................... 21
Fig.15 - ALCplus2 1+1 exp nodal..................................................................................... 22
Fig.16 - Synchronisation block diagram ............................................................................ 38
Fig.17 - IDU loopback .................................................................................................... 43
Fig.18 - ALplus2 with 16E1, 1+0 and 1+1 version, block diagram ........................................ 44
Fig.19 - ALPlus2 with 16E1, 2x(1+0) configuration, block diagram ....................................... 45
Fig.20 - ALCplus2 with 32E1 expansion, 1+0 and 1+1 version, block diagram ....................... 47
Fig.21 - ALCplus2 with 2E1, 1+0 and 1+1 version, block diagram ........................................ 48
Fig.22 - ALCplus2 with 16E1, 1+0 and 1+1 version, block diagram ...................................... 48
Fig.23 - AS and ASN ODUs ............................................................................................. 52

Fig.24 - Final 1+1 assembly with AS and ASN ODU ............................................................ 53
Fig.25 - ODU block diagram ............................................................................................ 54
Fig.26 - 1+1 hot stand–by 1 antenna ............................................................................... 55
Fig.27 - 1+1 hot stand–by 2 antennas ............................................................................. 55
Fig.28 - ATPC operation ................................................................................................. 56
Fig.29 - Grounding connection ........................................................................................ 60
Fig.30 - IDU ALplus2 front panel ..................................................................................... 62

Fig.31 - Pin-out Tributary 50 pin SCSI female ................................................................... 63
Fig.32 - Pin-out Tributary 50 pin SCSI female ................................................................... 65
Fig.33 - Antisliding strip ................................................................................................. 76
Fig.34 - 60–114 mm pole supporting plate fixing ............................................................... 77
Fig.35 - Adapting kit for 219 mm pole .............................................................................. 78
Fig.36 - Mounting position .............................................................................................. 79
Fig.37 - Possible positions of the support with ODU fast locking mechanism .......................... 80
Fig.38 - Band-it pole mounting kit ................................................................................... 81
Fig.39 - Installation onto the pole of the supporting plate ................................................... 82
Fig.40 - Position of the ODU body depending on the polarisation for 1+0. For 1+1 the polarisation
is always vertical: handle at the left side. .......................................................................... 83
Fig.41 - ODU body reference tooth .................................................................................. 84
Fig.42 - Final ODU assembly of 1+1 version...................................................................... 85
Fig.43 - ODU grounding ................................................................................................. 86
Fig.44 - Kit V32409 ....................................................................................................... 87
Fig.45 - Kit V32415 ....................................................................................................... 88
Fig.46 - Wall supporting plate ......................................................................................... 93
Fig.47 - Support with ODU fast locking mechanism ............................................................ 94
Fig.48 - Mounting possible positions................................................................................. 95

Fig.49 - Installation onto the wall of the supporting plate.................................................... 96
Fig.50 - Position of the ODU body depending on the polarisation for 1+0. For 1+1 the polarisation
is always vertical: handle at the left side. .......................................................................... 97
Fig.51 - ODU body reference tooth .................................................................................. 98
Fig.52 - Final ODU assembly of 1+1 version...................................................................... 99
Fig.53 - ODU grounding ............................................................................................... 100
Fig.54 - Kit V32409 ..................................................................................................... 101
Fig.55 - Kit V32415 ..................................................................................................... 102
Fig.56 - Centring ring position....................................................................................... 108

Fig.57 - Antislide strip.................................................................................................. 109
Fig.58 - Support mount on pole..................................................................................... 110
Fig.59 - Supporting system position ............................................................................... 111
Fig.60 - Hole E ............................................................................................................ 111
Fig.61 - Antenna installation on pole support................................................................... 112
Fig.62 -Position of the ODU handle depending on the polarisation for 1+0. For 1+1 the polarisation
is always horizontal. Handle at the right side.................................................................... 112
Fig.63 - Support system for ODU housing and reference tooth in evidence .......................... 113
Fig.64 - ODU body reference tooth ................................................................................ 114

Fig.65 - ODU housing final position for vertical polarization ............................................... 115
Fig.66 - ODU housing final position for horizontal polarization............................................ 115
Fig.67 - Hybrid and polarization disk .............................................................................. 116
Fig.68 - Polarization disk fixing (only for 13GHz and 15 GHz) ............................................ 117
Fig.69 - Hybrid mount on pole support ........................................................................... 118
Fig.70 - ODU housing final position for 1+1 version ......................................................... 119
Fig.71 - Vertical and horizontal adjustments ................................................................... 120

Fig.72 - Antenna aiming block....................................................................................... 121
Fig.74 - 1+0 pole mounting .......................................................................................... 127
Fig.76 - Position of the ODU handle depending on the polarisation for 1+0. For 1+1 the polarisation
Fig.77 - 1+0 support ................................................................................................... 129

Fig.78 - ODU housing final position for both polarization ................................................... 130
Fig.79 - Antenna aiming ............................................................................................... 131
Fig.81 - Hybrid and twist disk ....................................................................................... 133
Fig.82 - Polarization disk fixing (only for 13 GHz and 15 GHz) ........................................... 134
Fig.83 - Hybrid installation............................................................................................ 135
Fig.84 - 1+1 ODUs installation ...................................................................................... 136
Fig.85 - 1+0 pole mounting .......................................................................................... 142
Fig.87 - Position of the ODU handle depending on the polarisation for 1+0. For 1+1 the polarisation
Fig.88 - 1+0 support ................................................................................................... 144

Fig.89 - ODU housing final position for both polarization ................................................... 145
Fig.90 - Antenna aiming ............................................................................................... 146
Fig.92 - Hybrid and twist disk ....................................................................................... 148
Fig.93 - Polarization disk fixing (only for 13 GHz and 15 GHz) ........................................... 149
Fig.94 - Hybrid installation............................................................................................ 150
Fig.95 - 1+1 ODUs installation ...................................................................................... 151
Fig.96 - Detected voltage versus RF received signal ......................................................... 155
Fig.97 - Local Lan-1 port to remote Lan-1 port connection ................................................ 157
Fig.98 - Modulation and capacity ................................................................................... 158
Fig.99 - View Current Configuration ............................................................................... 158
Fig.100 - Switch general settings................................................................................... 159
Fig.101 - Lan-1 interface settings .................................................................................. 160
Fig.102 - Vlan settings for LAN-1.................................................................................... 160
Fig.103 - Vlan settings for Port A ................................................................................... 161
Fig.104 - Priority setting for Lan-1 and Port A ................................................................. 161
Fig.105 - 3 ports to 3 ports connections with segregated traffic ......................................... 162
Fig.106 - Modulation and capacity ................................................................................. 162

Fig.107 - View Current Configuration ............................................................................. 163
Fig.109 - Lan-1 interface settings .................................................................................. 164
Fig.110 - Lan1 Vlan settings ......................................................................................... 165
Fig.113 - Port A Vlan settings........................................................................................ 166

Fig.114 - Vlan Configuration Table ................................................................................. 167
Fig.115 - 3 ports to3 ports connections with segregated Tagged and Untagged traffic ........... 167
Fig.116 -Modulation and Capacity .................................................................................. 168
Fig.117 - View Current Configuration ............................................................................. 168
Fig.122 - Port A Vlan settings........................................................................................ 171
Fig.123 - Vlan Configuration Table ................................................................................. 171

Fig.124 - Subnetwork Craft Terminal - Communication setup ............................................ 173
Fig.125 - IP Ethernet ................................................................................................... 174
Fig.126 - LCT PPP ........................................................................................................ 174

Fig.127 - PPP Radio ..................................................................................................... 175
Fig.128 - Store Routing Table ....................................................................................... 176
Fig.129 - Stored Routing Table...................................................................................... 177
Fig.130 - Subnetwork Configuration Wizard .................................................................... 178
Fig.131 - Subnetwork Configuration Wizard - Actual Configuration ..................................... 179
Fig.132 - Add new station............................................................................................. 180

Fig.133 - Add New Network Element .............................................................................. 181

Fig.136 - Loop ............................................................................................................ 187
Fig.137 - Termination points for the Performance Monitoring ............................................. 187
Fig.138 - IDU GAI0165 ................................................................................................ 190

Fig.139 - IDU GAI0166 ................................................................................................ 190
Fig.140 - IDU P/N........................................................................................................ 191
Fig.141 - Label attached on the ODU mechanical body AL ................................................. 211

26 LIST OF TABLES
Tab.1 - Artificial respiration .............................................................................................. 9
Tab.2 - Optical interface characteristics .............................................................................24
Tab.3 - Guaranteed Ethernet Throughput (Mbit/s) for ALplus2/ALCplus2 (Ethernet only) ..........25
Tab.4 - Guaranteed Ethernet Latency (ms) for ALplus2/ALCplus2 (Ethernet only)....................26
Tab.5 - Rx Alarm Priority .................................................................................................29
Tab.6 - Maximum outage due to the Tx switching ...............................................................30
Tab.7 - Tx Alarm Priority .................................................................................................30
Tab.8 - IMAX and consumption..........................................................................................31
Tab.9 - E1 priority ..........................................................................................................41

Tab.10 - Characteristics of the cables................................................................................59
Tab.11 - 10/100/1000BaseT, RJ45 ...................................................................................62
Tab.12 - 8xE1, 50 pin SCSI female 75 Ohm ......................................................................63
Tab.13 - 8xE1, 50 pin SCSI female 120 Ohm) ....................................................................64
Tab.14 - RS232 SUB-D 9 pin male ...................................................................................65
Tab.15 - SUB-D 9 pin male USER IN/OUT) .........................................................................66
Tab.16 - MNGT/1 and MNGT/2 100BaseT connector pin-out for 10/100BaseT Ethernet connection
(RJ45) ...........................................................................................................................66
Tab.17 - CH1 connector pin-out for 9600 bit/s synchronous V.24 interface (RJ45)...................66
Tab.18 - CH1 connector pin-out for 9600 bit/s asynchronous V.24 interface (RJ45) .................67
Tab.19 - CH1 connector pin-out for 1x9600 or 2x4800 kbit/s V.28 interface (RJ45) .................67
Tab.20 - CH2 connector pin-out for 64 kbit/s channel - V.11 interface (RJ45) .........................67
Tab.21 - 2 Mbit/s wayside connector pin-out (RJ45)............................................................68
Tab.22 - Trib A, B connector ............................................................................................69
Tab.23 - SUB-D 9 pin male USER IN/OUT .........................................................................70
Tab.24 - Torques for tightening screws..............................................................................73
Tab.26 - Waveguide bending radius according to frequency .................................................75
Tab.29 - Waveguide bending radius according to frequency .................................................92
Tab.30 - Torques for tightening screws............................................................................ 105

Tab.33 - IDU part number .............................................................................................. 190
Tab.34 - Part number and description ............................................................................. 192
Tab.35 - ODU ASN part number and description ............................................................... 208

27 ASSISTANCE SERVICE
For more information, refer to the section relevant to the technical support on the Internet site of the com-
pany manufacturing the product.


Mn00224e E

Uploaded by

Copyright:

Available Formats

Mn00224e E

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mn00224e E

Uploaded by

Copyright:

Available Formats

What is the purpose of the manual?

What is the purpose of the manual?

What safety rules are outlined in the manual?

What safety rules are outlined in the manual?

ALS - ALCplus2

Access Link Series

1 DECLARATION OF CONFORMITY ............................................................................... 7

2 FIRST AID FOR ELECTRICAL SHOCK AND SAFETY RULES .......................................... 8

3 PURPOSE AND STRUCTURE OF THE MANUAL ............................................................12

5 SYSTEM PRESENTATION ..........................................................................................17

ALS - ALplus2, ALCplus2 - MN.00224.E - 001 1

6 TECHNICAL SPECIFICATIONS ..................................................................................23

7 ALPLUS2 IDU DESCRIPTION ....................................................................................34

8 ALCPLUS2 IDU DESCRIPTION ..................................................................................46

2 ALS - ALplus2, ALCplus2 - MN.00224.E - 001

9 ODU DESCRIPTION ..................................................................................................49

10 INSTALLATION AND PROCEDURES FOR ENSURING THE ELECTROMAGNETIC

12 ALCPLUS2 CONNECTORS ..........................................................................................69

ALS - ALplus2, ALCplus2 - MN.00224.E - 001 3

16 INSTALLATION ONTO THE POLE OF THE ODU WITH INTEGRATED ANTENNA

4 ALS - ALplus2, ALCplus2 - MN.00224.E - 001

18 LINE–UP OF THE RADIO HOP .................................................................................153

19 BACK UP FULL EQUIPMENT CONFIGURATION WITHOUT POSSIBILITY OF MODIFYING

20 LINE-UP FOR ETHERNET TRAFFIC ..........................................................................157

21 HOW TO CHANGE ADDRESS ON REMOTE EQUIPMENT WITHOUT LOSING THE

22 PROGRAMMING AND SUPERVISION .......................................................................185

23 COMPOSITION OF MODULAR IDU...........................................................................189

24 COMPOSITION OF OUTDOOR UNIT.........................................................................192

ALS - ALplus2, ALCplus2 - MN.00224.E - 001 5

25 LIST OF FIGURES ...................................................................................................213

26 LIST OF TABLES .....................................................................................................217

6 ALS - ALplus2, ALCplus2 - MN.00224.E - 001

SIAE Microelettronica S.p.A. declares that the products:

- digital radio relay system AS6

- digital radio relay system AS7

- digital radio relay system AS8

- digital radio relay system AS11

- digital radio relay system AS13

- digital radio relay system AS15

- digital radio relay system AS18

- digital radio relay system AS23

- digital radio relay system AS25

- digital radio relay system AS28

- digital radio relay system AS38

The following standards have been applied:

- EN 60950-1: 2006 “Safety of information technology equipment”.

2.1 FIRST AID FOR ELECTRICAL SHOCK

2.1.1 Artificial respiration

2.1.2 Treatment of burns

• Do not attempt to remove clothing from burnt sections

• Apply dry gauze on the burns

• Do not apply ointments or other oily substances.

Step Description Figure

Lift the patient’s head and let it recline backwards as far

3 While performing these operations take a good supply of oxy-

While performing these operations observe if the patient’s

Start with ten rapid expirations, hence continue at a rate of

2.2 SAFETY RULES

Fig.2 - Elasticized band