Scribd
Upload
45 views2 pages

Datasheet

The VIP Sensors Model 1006A is a small, lightweight triaxial piezoelectric accelerometer designed for vibration measurement in three axes without external power. It has a frequency response up to 5 kHz and resonance frequency of 30 kHz. The accelerometer utilizes PZT-5 crystal material and provides stable output sensitivity over an operating temperature range of -4°F to 248°F. It comes with low noise coaxial cables and is recommended for use with VIP Sensors signal conditioners.

Uploaded by

Senthamizhan Nandhakumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
45 views2 pages

Datasheet

The VIP Sensors Model 1006A is a small, lightweight triaxial piezoelectric accelerometer designed for vibration measurement in three axes without external power. It has a frequency response up to 5 kHz and resonance frequency of 30 kHz. The accelerometer utilizes PZT-5 crystal material and provides stable output sensitivity over an operating temperature range of -4°F to 248°F. It comes with low noise coaxial cables and is recommended for use with VIP Sensors signal conditioners.

Uploaded by

Senthamizhan Nandhakumar
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Quality

Innovations

Customer Satisfaction

PIEZOELECTRIC ACCELEROMETER
Vibration Measurement in Three Axes No External Power Required Frequency Response to 5 KHz Resonance Frequency at 30 KHz Light Weight (17 grams) Thru-Hole Center Mount
Description
The VIP Sensors Model 1006A is a small triaxial piezoelectric accelerometer designed for vibration measurement in three orthogonal axes. Its light weight (17 grams) minimizes mass loading. The accelerometer is a self-generating device that requires no external power source for operation. The transducer features three 10-32 receptacles for output connection and is typically screw mounted. The Model 1006A utilizes the PZT-5 crystal material, exhibiting stable output sensitivity over the operating temperature range. Signal ground is connected to the case of the unit. Low-noise, flexible coaxial cables are used for error-free operation. VIP Sensors Signal Conditioner Models 5002 and 5005 are recommended for use with this high impedance accelerometer.
in (mm) actual size

MODEL 1006A

0.984 (25) 0.787 (20) 0.984 (25) 0.787 (20) 2x 10-32 2-M5

Y X Z
H = 0.40 (10) H=10

Typical Amplitude Response


15.00 % DEVIATION 10.00 5.00 0.00 -5.00 1 10 100 1000 10000

Typical Temperature Response 15 10 5 0 -5 -10 -15 -50 (-46) 50 (10) 150 (66) 250 (121)
% DEVIATION

FREQUENCY (HZ)

350 (177)

TEMPERATURE F (C)
VIP Sensors California, USA
Ph (949) 429 3558 Fx (949) 528 0126 [email protected] www.vipsensors.com

VIP Sensors reserves the right to modify these specifications without notice. V01

Quality

Innovations

Customer Satisfaction

PIEZOELECTRIC ACCELEROMETER
SPECIFICATIONS
The following performance specifications conform to ISA-RP-37.2 (1964) and are typical values, referenced at +75F (+24C) and 100 Hz, unless otherwise noted. Calibration data, traceable to National Institute of Standards and Technology (NIST), is supplied.

MODEL 1006A

UNITS DYNAMIC CHARACTERISTICS Axial Sensitivity Transverse Sensitivity Frequency Response Resonance Frequency Amplitude Response [1] +5% + 1 dB Temperature Response Amplitude Linearity ELECTRICAL CHARACTERISTICS Output Polarity Resistance Capacitance Grounding G pF pC/g % Hz Hz Hz % 13 (10 minimum) 5 See Typical Amplitude Response 30,000 1 5,000 0.5 6,000 See Typical Temperature Response <1

Acceleration directed from the base into the transducer is defined as positive >1 1,500 Signal ground connected to case

ENVIRONMENTAL CHARACTERISTICS Temperature Range Humidity Shock Limit g pk Base Strain equiv. g pk/ strain Magnetic Field Sensitivity equiv. g rms/gauss (/T) Thermal Transient Sensitivity equiv. g pk/F (/C) PHYSICAL CHARACTERISTICS Weight Case Material Mounting Piezoelectric Material Structure Output Connector ACCESSORIES
Included: 9006-120 Cable, Low Noise 10-32/10-32, 3.3 m, qty 3 9509-1 M5 Mounting Screw Calibration Certificate

-4F to 248F (-20C to +120C) Epoxy sealed 2,000 0.004 5E-6 (0.5) 0.0144 (0.008)

oz (grams)

0.6 (17) Stainless Steel


Center mount with M5 screw, two side mounts with 10-32, torque 2 N-m (18 lbf-in)

PZT-5 Flat Plate Shear 10-32 receptacles for X, Y and Z

Optional: 9604 Cable Adapters 10-32/10-32 (extend cable length)

NOTES
1. Low end response of the transducer is a function of its electronics.

VIP Sensors California, USA

Ph (949) 429 3558 Fx (949) 528 0126

[email protected] www.vipsensors.com

VIP Sensors reserves the right to modify these specifications without notice. V01

You might also like