IEEE 802.15.

IEEE 802.15.4 is a technical standard which defines the operation of a low-rate wireless personal
area network (LR-WPAN). It specifies the physical layer and media access control for LR-WPANs,
and is maintained by the IEEE 802.15 working group, which defined the standard in 2003.[1] It is
the basis for the Zigbee,[2] ISA100.11a,[3] WirelessHART, MiWi, 6LoWPAN, Thread and SNAP
specifications, each of which further extends the standard by developing the upper layers which
are not defined in IEEE 802.15.4. In particular, 6LoWPAN defines a binding for the IPv6 version of
the Internet Protocol (IP) over WPANs, and is itself used by upper layers like Thread.

Overview

IEEE standard 802.15.4 intends to offer the fundamental lower network layers of a type of
wireless personal area network (WPAN) which focuses on low-cost, low-speed ubiquitous
communication between devices. It can be contrasted with other approaches, such as Wi-Fi,
which offer more bandwidth and requires more power. The emphasis is on very low cost
communication of nearby devices with little to no underlying infrastructure, intending to exploit
this to lower power consumption even more.

The basic framework conceives a 10-meter communications range with line-of-sight at a

transfer rate of 250 kbit/s. Bandwidth tradeoffs are possible to favor more radically embedded
devices with even lower power requirements for increased battery operating time, through the
definition of not one, but several physical layers. Lower transfer rates of 20 and 40 kbit/s were
initially defined, with the 100 kbit/s rate being added in the current revision.
Even lower rates can be used, which results in lower power consumption. As already mentioned,
the main goal of IEEE 802.15.4 regarding WPANs is the emphasis on achieving low
manufacturing and operating costs through the use of relatively simple transceivers, while
enabling application flexibility and adaptability.

Key 802.15.4 features include:

1. real-time suitability by reservation of Guaranteed Time Slots (GTS).

2. collision avoidance through CSMA/CA.

3. integrated support for secure communications.

4. power management functions such as link speed/quality and energy detection.

5. Support for time and data rate sensitive applications because of its ability to operate either
as CSMA/CA or TDMA access modes. The TDMA mode of operation is supported via the
GTS feature of the standard.[4]

6. IEEE 802.15.4-conformant devices may use one of three possible frequency bands for
operation (868/915/2450 MHz).

Protocol architecture

IEEE 802.15.4 protocol stack

Devices are designed to interact with each other over a conceptually simple wireless network.
The definition of the network layers is based on the OSI model; although only the lower layers are
defined in the standard, interaction with upper layers is intended, possibly using an IEEE 802.2
logical link control sublayer accessing the MAC through a convergence sublayer.
Implementations may rely on external devices or be purely embedded, self-functioning devices.

The physical layer

The physical layer is the bottom layer in the OSI reference model used worldwide, and protocols
layers transmit packets using it

The physical layer (PHY) provides the data transmission service. It also, provides an interface to
the physical layer management entity, which offers access to every physical layer management
function and maintains a database of information on related personal area networks. Thus, the
PHY manages the physical radio transceiver, performs channel selection along with energy and
signal management functions. It operates on one of three possible unlicensed frequency bands:

868.0–868.6 MHz: Europe, allows one communication channel (2003, 2006, 2011[5])

902–928 MHz: North America, originally allowed up to ten channels (2003), but since has
been extended to thirty (2006)

2400–2483.5 MHz: worldwide use, up to sixteen channels (2003, 2006)

The original 2003 version of the standard specifies two physical layers based on direct-
sequence spread spectrum (DSSS) techniques: one working in the 868/915 MHz bands with
transfer rates of 20 and 40 kbit/s, and one in the 2450 MHz band with a rate of 250 kbit/s.

The 2006 revision improves the maximum data rates of the 868/915 MHz bands, bringing them
up to support 100 and 250 kbit/s as well. Moreover, it goes on to define four physical layers
depending on the modulation method used. Three of them preserve the DSSS approach: in the
868/915 MHz bands, using either binary or QPSK offset quadrature phase-shift keying (the
second of which is optional); in the 2450 MHz band, using QPSK.

An optional alternative 868/915 MHz layer is defined using a combination of binary keying and
amplitude-shift keying (thus based on parallel, not sequential spread spectrum, PSSS). Dynamic
switching between supported 868/915 MHz PHYs is possible.

Beyond these three bands, the IEEE 802.15.4c study group considered the newly opened 314–
316 MHz, 430–434 MHz, and 779–787 MHz bands in China, while the IEEE 802.15 Task Group
4d defined an amendment to 802.15.4-2006 to support the new 950–956 MHz band in Japan.
First standard amendments by these groups were released in April 2009.

In August 2007, IEEE 802.15.4a was released expanding the four PHYs available in the earlier
2006 version to six, including one PHY using Direct Sequence ultra-wideband (UWB) and another
using chirp spread spectrum (CSS). The UWB PHY is allocated frequencies in three ranges:
below 1 GHz, between 3 and 5 GHz, and between 6 and 10 GHz. The CSS PHY is allocated
spectrum in the 2450 MHz ISM band.[6]

In April, 2009 IEEE 802.15.4c and IEEE 802.15.4d were released expanding the available PHYs
with several additional PHYs: one for 780 MHz band using O-QPSK or MPSK,[7] another for
950 MHz using GFSK or BPSK.[8]

IEEE 802.15.4e was chartered to define a MAC amendment to the existing standard 802.15.4-
2006 which adopts channel hopping strategy to improve support for the industrial markets,
increases robustness against external interference and persistent multi-path fading. On February
6, 2012, the IEEE Standards Association Board approved the IEEE 802.15.4e which concluded all
Task Group 4e efforts.

The MAC layer

The medium access control (MAC) enables the transmission of MAC frames through the use of
the physical channel. Besides the data service, it offers a management interface and itself
manages access to the physical channel and network beaconing. It also controls frame
validation, guarantees time slots and handles node associations. Finally, it offers hook points for
secure services.

Note that the IEEE 802.15 standard does not use 802.1D or 802.1Q, i.e., it does not exchange
standard Ethernet frames. The physical frame-format is specified in IEEE802.15.4-2011 in
section 5.2. It is tailored to the fact that most IEEE 802.15.4 PHYs only support frames of up to
127 bytes (adaptation layer protocols such as the IETF's 6LoWPAN provide fragmentation
schemes to support larger network layer packets).

Higher layers

No higher-level layers and interoperability sublayers are defined in the standard. Other
specifications, such as Zigbee, SNAP, and 6LoWPAN/Thread, build on this standard. RIOT,
OpenWSN, TinyOS, Unison RTOS, DSPnano RTOS, nanoQplus, Contiki and Zephyr operating
systems also use a few items of IEEE 802.15.4 hardware and software.

Network model

Node types

The standard defines two types of network node.

The first one is the full-function device (FFD). It can serve as the coordinator of a personal area
network just as it may function as a common node. It implements a general model of
communication which allows it to talk to any other device: it may also relay messages, in which
case it is dubbed a coordinator (PAN coordinator when it is in charge of the whole network).

On the other hand, there are reduced-function devices (RFD). These are meant to be extremely
simple devices with very modest resource and communication requirements; due to this, they
can only communicate with FFDs and can never act as coordinators.

Topologies

IEEE 802.15.4 star and peer-to-peer

IEEE 802.15.4 cluster tree

Networks can be built as either peer-to-peer or star networks. However, every network needs at
least one FFD to work as the coordinator of the network. Networks are thus formed by groups of
devices separated by suitable distances. Each device has a unique 64-bit identifier, and if some
conditions are met, short 16-bit identifiers can be used within a restricted environment. Namely,
within each PAN domain, communications will probably use short identifiers.

Peer-to-peer (or point-to-point) networks can form arbitrary patterns of connections, and their
extension is only limited by the distance between each pair of nodes. They are meant to serve as
the basis for ad hoc networks capable of performing self-management and organization. Since
the standard does not define a network layer, routing is not directly supported, but such an
additional layer can add support for multihop communications. Further topological restrictions
may be added; the standard mentions the cluster tree as a structure which exploits the fact that
an RFD may only be associated with one FFD at a time to form a network where RFDs are
exclusively leaves of a tree, and most of the nodes are FFDs. The structure can be extended as a
generic mesh network whose nodes are cluster tree networks with a local coordinator for each
cluster, in addition to the global coordinator.

A more structured star pattern is also supported, where the coordinator of the network will
necessarily be the central node. Such a network can originate when an FFD decides to create its
own PAN and declare itself its coordinator, after choosing a unique PAN identifier. After that,
other devices can join the network, which is fully independent from all other star networks.

Data transport architecture

Frames are the basic unit of data transport, of which there are four fundamental types (data,
acknowledgment, beacon and MAC command frames), which provide a reasonable tradeoff
between simplicity and robustness. Additionally, a superframe structure, defined by the
coordinator, may be used, in which case two beacons act as its limits and provide
synchronization to other devices as well as configuration information. A superframe consists of
sixteen equal-length slots, which can be further divided into an active part and an inactive part,
during which the coordinator may enter power saving mode, not needing to control its network.

Within superframes contention occurs between their limits, and is resolved by CSMA/CA. Every
transmission must end before the arrival of the second beacon. As mentioned before,
applications with well-defined bandwidth needs can use up to seven domains of one or more
contentionless guaranteed time slots, trailing at the end of the superframe. The first part of the
superframe must be sufficient to give service to the network structure and its devices.
Superframes are typically utilized within the context of low-latency devices, whose associations
must be kept even if inactive for long periods of time.

Data transfers to the coordinator require a beacon synchronization phase, if applicable, followed
by CSMA/CA transmission (by means of slots if superframes are in use); acknowledgment is
optional. Data transfers from the coordinator usually follow device requests: if beacons are in
use, these are used to signal requests; the coordinator acknowledges the request and then
sends the data in packets which are acknowledged by the device. The same is done when
superframes are not in use, only in this case there are no beacons to keep track of pending
messages.

Point-to-point networks may either use unslotted CSMA/CA or synchronization mechanisms; in

this case, communication between any two devices is possible, whereas in "structured" modes
one of the devices must be the network coordinator.

In general, all implemented procedures follow a typical request-confirm/indication-response

classification.
Reliability and security

The physical medium is accessed through a CSMA/CA protocol. Networks which are not using
beaconing mechanisms utilize an unslotted variation which is based on the listening of the
medium, leveraged by a random exponential backoff algorithm; acknowledgments do not adhere
to this discipline. Common data transmission utilizes unallocated slots when beaconing is in
use; again, confirmations do not follow the same process.

Confirmation messages may be optional under certain circumstances, in which case a success
assumption is made. Whatever the case, if a device is unable to process a frame at a given time,
it simply does not confirm its reception: timeout-based retransmission can be performed a
number of times, following after that a decision of whether to abort or keep trying.

Because the predicted environment of these devices demands maximization of battery life, the
protocols tend to favor the methods which lead to it, implementing periodic checks for pending
messages, the frequency of which depends on application needs.

Regarding secure communications, the MAC sublayer offers facilities which can be harnessed
by upper layers to achieve the desired level of security. Higher-layer processes may specify keys
to perform symmetric cryptography to protect the payload and restrict it to a group of devices or
just a point-to-point link; these groups of devices can be specified in access control lists.
Furthermore, MAC computes freshness checks between successive receptions to ensure that
presumably old frames, or data which is no longer considered valid, does not transcend to higher
layers.

In addition to this secure mode, there is another, insecure MAC mode, which allows access
control lists[2] merely as a means to decide on the acceptance of frames according to their
(presumed) source.

See also

References

External links
Retrieved from
"https://en.wikipedia.org/w/index.php?
title=IEEE_802.15.4&oldid=1129152105"

Last edited 8 days ago by XXV