o Home

 
o Piping Tutorial
 
o Piping Interview Questions
PIPING INTERVIEW QUESTIONS & ANSWERS

Are you in a dilemma to decide your future due to heavy competition? Are you not
getting right job in spite of being repeated attempts? Have you got low self-esteem?
Then change your mind by checking at wisdom jobs online portal. Piping is a system of
pipes used to convey fluids from one location to another. The advantage of piping is
that they are easily transported as a compact pile of parts on a wagon and then
assembled as a hollow structure at the jobsite. The role of a piping engineer is to design
and build piping systems that carry out water, oil and waste. So, trace out your career as
piping designer, structural designer, piping engineer, junior mechanical engineer, steam
fitter and so on by seeing through the below offered piping job interview questions and
answers.

Piping Interview Questions And Answers

  Prev
  Piping Jobs

  All Interview Questions

1. Question 1. What Is Preferred Location For Drain?

Answer :
Must be located at the bottom section of drum.
2. Question 2. What Are The Steps In Selection Of Valve?
Answer :
What to handle, liquid, gas or powder, fluid nature, function, construction
material, disc type, stem type, how to operate, bonnet type, body ends, delivery
time, cost, warranty.

AutoCAD Interview Questions

3. Question 3. What Are Functions Of Valves?
Answer :
Isolation, regulation, non-return and special purposes.
4. Question 4. What Are Isolating Valves?
Answer :
Gate, ball, plug, piston, diaphragm, butterfly, pinch.
5. Question 5. What Are Regulating Valves?
Answer :
Globe, needle, butterfly, diaphragm, piston, punch.

Mechanical Engineering Interview Questions

6. Question 6. What Are Non-return Valves?
Answer :
check valve.
7. Question 7. What Are Special Valves?
Answer :
Multi-port, flush bottom, float, foot, pressure relief, breather.

Mechatronics engineering Interview Questions

8. Question 8. What Materials Are Used For Construction Of Valves?
Answer :
Cast iron, bronze, gun metal, carbon steel, stainless steel, alloy carbon steel,
polypropylene and other plastics, special alloys.
9. Question 9. What Is Trim?
Answer :
Trim is composed of stem, seat surfaces, back seat bushing and other small
internal parts that normally contact the surface fluid.

Auto mechanic Interview Questions

10. Question 10. Which Standard Specifies Trim Numbers For Valve?
Answer :
API 600.
11. Question 11. What Are Wetted Parts Of Valve?
Answer :
All parts that come in contact with surface fluid are called wetted parts.

3d Printing Interview Questions

12. Question 12. What Is Wire Drawing?
Answer :
This term is used to indicate the premature erosion of the valve seat caused
by excessive velocity between seat and seat disc, when valve is not closed
tightly.

AutoCAD Interview Questions

13. Question 13. What Is Straight Through Valve?
Answer :
Valve in which the closing operation of valve is achieved by 90 degrees turn of
the closing element.
14. Question 14. What Pressure Tests Are Carried Out On Valves?
Answer :
Shell-hydrostatic, seat-hydrostatic, seat-pneumatic
15. Question 15. What Are Available Valve Operators?
Answer :
Hand-lever, hand-wheel, chain operator, gear operator etc.

Piping Design Engineer Interview Questions

16. Question 16. What Is The Full Form Of Asme?
Answer :
 American Society for Mechanical Engineers.
17. Question 17. Which Piping Code Is Used For Power Piping And Which Code Is
Used For Process Piping Design?
Answer :
Power Piping: ASME B 31.1
Process Piping: ASME B 31.3
Mechanical Fitter Interview Questions
18. Question 18. What Are The Main Differences Between Asme B 31.1 And
Asme B 31.3?
Answer :
The main differences are listed below:
o Material allowable stresses are different in both codes.
o Stress increases due to occasional loads are different in each code.
o B 31.3 neglects torsion while calculating sustained stresses, but B
31.1 includes it.
o Sustained stress calculation is specific in B 31.1 but undefined for B
31.3.
o B 31.1 intensifies torsion but B31.3 does not intensify it.

Mechanical Engineering Interview Questions

19. Question 19. How To Calculate The Basic Allowable Stress For A Material?
Answer :
The basic allowable stress is defined in respective code. For example as per
B 31.3 the basic allowable stress for a material is the minimum of the
following:
o 1/3rd of tensile strength at design temperature.
o 2/3rd of yield strength at design temperature.
o 100% of average stress for a creep rate of 0.01% per 1000 hours.
o 67% of average stress for rupture at the end of 100000 hours.
o 80% of minimum stress for ruptures at the end of 100000 hours.
o For austenitic stainless steel or nickel alloys the lower of yield
strength and 90% of yield strength at temperature.
o For structural grade materials 0.92 times of the lowest value of point
(a) to (f)
20. Question 20. What Is The Main Difference Between Constant And Variable
Spring Hanger? When To Use These Hangers?
Answer :
In Constant Spring hanger the load remains constant throughout its travel
range. But In variable spring hanger the load varies with displacement.
 Spring hangers are used when thermal displacements are upwards and piping
system is lifted off from the support position. Variable spring hanger is
preferable as this is less costly.
Constant springs are used:
o When thermal displacement exceeds 50 mm
o When variability exceeds 25%
o Sometimes when piping is connected to strain sensitive equipment
like steam turbines, centrifugal compressors etc and it becomes very
difficult to qualify nozzle loads by variable spring hangers, constant
spring hangers can be used.
Pipe Fitter Interview Questions
21. Question 21. What Do You Mean By Variability? What Is The Industry
Approved Limit For Variability?
Answer :
Variability= (Hot Load-Cold load)/Hot load = (Spring Constant ×
displacement)/Hot load.
Limit for variability for variable spring hangers is 25%.
22. Question 22. What Are The Major Parameters You Must Address While
Making A Spring Data-sheet?
Answer :
Major parameters are: Spring TAG, Cold load/Installed load, Vertical and
horizontal movement, Piping design temperature, Piping Material, Insulation
thickness, Hydro-test load, Line number etc.
23. Question 23. How To Calculate The Height Of A Variable Spring Hanger?
Answer :
o Select the height from vendor catalog based on spring size and
stiffness class.
o For base mounted variable spring hanger the height is mentioned
directly. It is the spring height.
o For top mounted variable spring hanger’s ass spring height with
turnbuckle length, clamp/lug length and rod length.
24. Question 24. Can You Select A Proper Spring Hanger If You Do Not Make It
Program Defined In Your Software? What Is The Procedure?
Answer :
In your system first decide the location where you want to install the spring.
Then remove all nearby supports which are not taking load in thermal
operating case. Now run the program and the sustained load on that support
node is your hot load. The thermal movement in that location is your thermal
 movement for your spring. Now assume variability for your spring. So
calculate
Spring constant = (Hot load × variability)/displacement. Now with spring
constant and hot load enter any vendor catalog to select spring inside the
travel range.

Mechatronics engineering Interview Questions

25. Question 25. What Is The Software Available For Performing Piping Stress
Analysis?
Answer :
Caesar II, Auto Pipe etc.

Piping Related Interview Questions

AutoCAD Interview Questions Mechanical
Engineering
Interview
Questions

Mechatronics engineering Interview Questions Auto mechanic

Interview
Questions

3d Printing Interview Questions Piping Design

Engineer
Interview
Questions

Mechanical Fitter Interview Questions Pipe Fitter

Interview
Questions

Piping Related Practice Tests

AutoCAD Practice Tests Mechanical
Engineering
Practice Tests

Mechatronics engineering Practice Tests

Piping Related Interview Questions

AWS-CWI
Certification |
Certified Welding
Inspector Exam
Training Course
Eurotech an authorized Agent of American Welding Society Organizing AWS CWI,
SCWI, CAWI , CWE, WI, Certification Program in these Locations: Mumbai, Chennai,
Ahmedabad, New Delhi, INDIA. Register Now & Get all information about Preparation,
Training, Seminar, Exam Schedules and etc..

 Home
 Welding Courses
 Training Schedules
 Knowledge Base
 CWI Practice Test
 Submit Your Enquiry

piping supervisor interview questions and answers

Top 10 Interview Questions Related To Pipes Supports
POSTED ON SEPTEMBER 7, 2017
Piping Related Interview Questions
4 Votes

Interview Questions Related To pipes Supports:-

1. What are the Criteria for Pipe Supporting?

Answer: –

Following are the points, which should be taken into account for proper supporting: –
A. Load of bare pipe + fluid + insulation (if any).
B. Load of bare pipe + water fill.
C. Load of valves and online equipment and instrument.
D. Thermal loads during operation.
E. Steam out condition, if applicable.
F. Wind loads for piping at higher elevation, if required.
G. Forced vibration due to pulsating flow.
H. Bare pipe with size above 12” shall be supported with Pad or Shoe.

2. What is the basic span of supports for 2”/6”/10”/24” pipe?

Answer: –
Basic Span is 5.5m / 9m / 11.5m / 15m respectively.

3. What is the function of providing the anchor, cross guide and guide for

piping?
Answer: –
Anchor is provided to restrict all the axial and rotational movements of pipe, whereas cross
guide is
provided to restrict displacements of pipe along with the axis perpendicular to its centerline
and Guide is provided to restrict the longitudinal movements of pipes along with its axis.

4. How is piping to Tank inlet nozzle is supported and why?

Answer: –
Piping to Tank Nozzle is supported with spring type support (first support from Nozzle) in
order to
Piping Related Interview Questions
make the nozzle safe from the loads which occurs due to the displacement of pipe
( Displacement
may be due to thermal expansion of pipe, tank material, tank settlement etc).
Advertisements

REPORT THIS AD

5. What are the types of flexible spring hangers?

Answer: –
1. Constant Spring Hanger 2. Variable Spring Hanger.

6. What is the purpose of providing Graphite Pads in supports below shoes?

Answer: –
To reduce the friction factor. The coefficient of friction for Graphite Pads is 0.1

7. Where do you provide Anchor and Slotted Support of Heat Exchanger?

Answer: –
Anchor support of Heat exchanger is provided on the side from which Tube bundle will be
pulled out for the purpose of maintenance work also it is based on the growth of the
connecting piping as
exchanger should grow with the piping.

8. What should be the material of shoes for supporting AS pipes & why?
Answer: –
If CS shoes are used then pad in contact with the pipe shall be of Alloy steel to avoid
dissimilar
welding at pipe. To avoid alloy steel welding and dissimilar welding, fabricated clamps
either of CS or SS can be used.

9. What are sway braces?

Answer: –
Sway braces are essentially a double acting spring housed in a canister. Their purpose is to
limit the
undesirable movement. Undesirable movement means movement caused by wind loading,
rapid
valve closure, relief valve opening, two phase flow or earthquake.
Piping Related Interview Questions

10. What is the difference between variable spring hanger and constant spring

hanger?
Answer: –
Variable spring Hanger: –
As the name itself indicates the resistance of the coil to a load changes during compression.
Constant spring Hanger: –
Constant spring hanger provides constant support force for pipes and equipment subjected
to vertical movement due to thermal expansion.

Advertisements

REPORT THIS AD

This entry was posted in Interview Questions and Answers, Piping Interview Questions Answers and
tagged Bergen Power Pipe Supports Interview Questions, interview questions on piping
projects, mechanical piping interview questions, Pipe Interview Questions, Piping Design Engineer
Interview Point Questions, piping foreman interview questions and answers, piping foreman interview
questions pdf, Piping interview Q&A | Piping Engineer, Piping interview questions, piping interview
questions with answers, piping qc inspector interview questions, piping questionnaire pdf, piping
questionnaire pdf free download, Piping Stress Job Interview Questions, piping supervisor interview
questions and answers, Piping Support Interview Question, Piping Text into Questions and
Answers, Question and Answers on Piping related topics, Questions Related to Pipes
Supports, Searches related to Interview Questions Related To Pipes Supports, Typical Questions For
Piping Engineer's Knowledge Testing, Westinghouse Pipe Support Engineer Interview
Questions, What are technical questions for piping?.

Questions related to Pipe Fittings: –

POSTED ON NOVEMBER 30, 2016
16 Votes

1. How can flanges be classified based on Pipe Attachment?

 Answer: –
Flanges can be classified based on pipe attachment as: –
Slip – on. : – The Slip-on type flanges are attached by welding inside as well as outside.
Piping Related Interview Questions
These flanges are of forged construction.
Socket Weld. : – The Socket Weld flanges are welded on one side only. These are used
for small bore lines only.
Screwed. : – The Screwed-on flanges are used on pipelines where welding cannot be carried
out.
Lap Joint. : – The Lap Joint flanges are used with stub ends. The stub ends are welded with
pipes & flanges are kept loose over the same.
Welding Neck. : – The Welding neck flanges are attached by butt welding to the pipe.
These are used mainly for critical services where the weld joints need radiographic
inspection.
Blind. : – The Blind flanges are used to close the ends which need to be reopened.
Reducing. : – The reducing flanges are used to connect between larger and smaller sizes
without using a reducer. In case of reducing flanges, the thickness of flange should be that of
the higher diameter.
Integral. : – Integral flanges are those, which are cast along with the piping
component or equipment.

2. How can flanges be classified based on Pressure- temperature ratings?

Answer: –
Flanges are classified based on pressure temperature ratings as: –
#A. 150
#B. 300
#C. 400
#D. 600
#E. 900
#F. 1500
#G. 2500
Pressure temperature rating carts in the standard ASME16.5 specify the non-shock working
gauge pressure to which the flange can be subjected to at a particular temperature.

3. How can flanges be classified based on facing?

Answer: –
Piping Related Interview Questions
Flanges are classified based on facing as: –

1. Flat face. (FF)

2. Raised face. (R/F)
3. Tongue and groove. (T/G)
4. Male and female. (M/F)
5. Ring type joint. (RTJ)

4. How can flanges be classified based on face finish?

Answer: –
Flanges are classified based on face finish as: –

1. Smooth finish.
2. Serrated finish.

5. Where the smooth finish flange & serrated finish flange finds its use?
Answer: –
The smooth finish flange is provided when metallic gasket is provided and serrated finish
flange is provided when non-metallic gasket is provided.

6. What are the types of serrated finish provided on flange face?

Answer: –

1. Concentric or
2. Spiral (Phonographic)

7. How the serration on flanges is specified?

Answer:
The serration on flanges is specified by the number, which is the Arithmetic Average Rough
Height (AARH).

8. Where the concentric serration is insisted for face finish?

Piping Related Interview Questions
Answer: –
Concentric serration are insisted for face finish where the fluid being carried has very low
density and can find leakage path through cavity.

9. How the Gaskets are classified based on the type of construction?

Answer: –
Based on the type of construction, gaskets are classified as: –

1. Full face.
2. Spiral wound metallic.
3. Ring type.
4. Metal jacketed.
5. Inside bolt circle.

10.What is the most commonly used material for Gasket?

Answer: –
Compressed Asbestos Fibre.

11.Which type of gasket is recommended for high temperature & high-

pressure application?
Answer: –
Spiral Wound Metallic Gasket.

11.What are the criteria for selection of MOC of Spiral Wound metallic

Gasket winding material?
Answer: –
The selection of material of construction for Gasket winding depends upon: –

1. The corrosive nature and concentration of fluid being carried.

2. The operating temperature of the fluid.
3. The relative cost of alternate winding material.
Piping Related Interview Questions

12.What are the most common materials used for spiral wound metallic

gasket winding?
Answer: –
The most commonly used material for spiral wound metallic gasket winding is: –

1. Austenitic stainless steel 304 with asbestos filler.

2. Austenitic stainless steel 316 with asbestos filler.
3. Austenitic stainless steel 321 with asbestos filler.

13.Which material is used as filler material for spiral wound gasket in case

of high temperature services?
Answer: –
For very high temperature services, graphite filler is used.

14.What is centering ring in connection to spiral wound gasket?

Answer: –
Spiral wound gaskets are provided with carbon steel external ring called centering ring.

15.What will be the AARH finish on flange face for using spiral wound

gasket?
Answer: –
125-250 AARH finish.

16.On which type of flanges the use of spiral wound gasket are restricted?
Answer: –
rating spiral wound gasket on flanges other#ASME B16.5 does not recommend the use of
150 than welding neck and lapped joint type.
Piping Related Interview Questions

17.Up to what temperature limits the low strength carbon steel bolts

should not be used for flanged joints?

Answer: –
C.°C or below – 28°Flanged joints using low strength carbon steel shall not be used above
200

17.How the pipe fittings are classified based on end connections?

Answer: –
Pipe fittings are classified based on end connection as: –

1. Socket weld fittings.

2. Screwed end fittings.
3. Beveled end or Butt weld fittings.
4. Spigot socket fittings.
5. Buttress end fittings.

18.Up to what temperature the carbon steel materials shall be used?

Answer: –
Carbon steel materials shall be used for temperature up to 425C°

19.Which material is used for temperature above 426C°?

Answer: –
Alloy steel materials shall be used for temperature above 426 C°

20.Which type of material is used for corrosive fluid?

Answer: –
Stainless steel materials shall be used for corrosive fluid.

21.Which type of piping materials are used for drinking water, instrument
Piping Related Interview Questions

air etc?
Answer: –
Galvanized steel materials shall be used for drinking water, instrument air and NI lines
(LP).

22.What is the difference between Pipe and Tube?

Answer: –
Pipe is identified by NB and thickness is defined by Schedule whereas Tube is identified by
OD & its thickness as BWG (Brimingham wire gauge or 1/100 inch).

23.From which size onwards NB of pipe is equal to OD of Pipe?

Answer: –
From the size 14” and onwards NB = OD of pipe.

24.What should be the radius of long radius elbow?

Answer:
1.5D (Where “D” is the diameter of the pipe.)

25.What should be the radius of short radius elbow?

Answer:-
1D(Where “D” is the diameter of the pipe.)

26.What is the basis of using of short radius & long radius elbow?
Answer:-
Long radius elbow are used for small pressure drop whereas short radius elbow are used for
high pressure drops. For catalyst flows vary long radius elbows are used.

27.Normally where do we use the following?

(1) Eccentric reducers.   (2) Concentric reducers.
Answer:
Piping Related Interview Questions

1. Eccentric reducers = Pump suction to avoid Cavitation, To maintain elevation (BOP) in rack.
2. Concentric reducers = Pump discharge, vertical pipeline etc.

28.Concentric reducer is used in pump suction. (Yes / No). Explain.

Answer:
No. Air pockets may form if concentric reducer is used at pump suction, which results in
cavitation
and cause damage to Pump. To avoid this problem, Eccentric Reducer with flat side up
(FSU) is
used in Pump Suction.

29.Where the ERW spiral & longitudinal pipes are used?

Answer: –
Use depends upon the availability of pipes. Nothing functional difference.

30.Where the ERW & Seamless pipes are used?

Answer: –
Above 18” ERW pipes are used. Below 18” seamless pipes are used. Seamless pipes can
sustain
higher temperature & pressure.

31.What is the main use of ASTM A53 & A106 Gr.B pipes?
Answer: –
ASTM A53 pipes are mainly used for utility services whereas A106 Gr. B pipes are used for
high
Pressure & high temperature services.

32.From which side of pipe will you take a branch connection?

Answer:-
Piping Related Interview Questions
When fluid is Gas, Air or Steam and Cryogenic Service – Topside.
When Fluid is Liquid – Bottom Side.

33.Why don’t we take a branch for Cryogenic Service from bottom side

though the fluid is in liquid state?

Answer: –
There is the chance of ice formation during normal operation and since ice flows from the
bottom of the pipe it will block the branch pipe connection.

33.Why do we provide High Point Vent (HPV) and Low Point Drain (LPD)

in piping?
Answer:
HPV – For removing Air during Hydro-test.
LPD – For draining water after conducting Hydro-test.

34.What do you mean by Jacketed Piping?

Answer: –
Piping which is recognized as providing the most uniform application of heat to the process,
as well
as maintaining the most uniform processing temperatures where steam tracing is not
capable of
maintaining the temperature of fluid constant. Usually used for molten sulphur, Polymers
service.

35.What is the minimum distance to be maintained between two welds in a

pipe?
Answer: –
The thumb rule is that the minimum distance between adjacent butt welds is 1D. If not, it is
never
closer than 1-1/2″. This is supposedly to prevent the overlap of HAZs. Minimum spacing of
circumferential welds between centerlines shall not be less than 4 times the pipe wall
Piping Related Interview Questions
thickness or
25 mm whichever is greater.

36.What do you mean by IBR and which lines comes under IBR purview?
Answer: –
IBR: Indian Boiler Regulation Act.
Steam lines with conditions listed bellow comes under IBR purview : –

 Lines for which design pressure is 3.5 kg/sq. cm and above.

 Line size above 10” having design pressure 1.0 kg/sq. cm and above.
 Boiler feed water lines to steam generator, condensate lines to steam generator and flash
drum.

37.What are Weldolet and Sockolet? And where they are used?
Answer:-
Weldolet and Sockolet are basically self-reinforced fittings.
Weldolet is used for Butt weld branch connection where standard tee is not available due to
size
restrictions and the piping is of critical / high-pressure service. Sockolet is used for socket
welding
branch connection, which require reinforcing pad.

38.What is the MOC for Superheated high pressure Steam Lines?

Answer:-
A 335 Gr. P I / P 11, Composition: Cr. – ½ Mo (P1) / 1¼ Cr. – ½ Mo (P11)

39.What is the normal upstream and downstream straight length of orifice

flow meter?
Answer: –
Upstream – 15D Downstream – 5D

This entry was posted in Interview Questions and Answers, Piping Interview Questions Answers and
Piping Related Interview Questions

tagged 22 Pipefitter Interview Questions and 132 Answers, most commonly asked questions in piping
interview, pipe fitter interview questions and answers, pipe fitter interview questions pdf, Pipe Fittings
Frequently Asked Questions, Pipe Fittings- FAQ, pipefitter questions answers, piping interview
question and answer pdf, piping questions and answers pdf, piping questions and answers pdf free
download, piping supervisor interview questions and answers, Question and Answers on Piping related
topics, Questions about piping issues, Questions Related to Pipe Fittings, SAMPLE TEST
QUESTIONS STEAMFITTER/PIPEFITTER, Searches related to Questions related to Pipe
Fittings, Top 10 piping interview questions with answers.

Interview Questions Answers Related to Codes & standard

POSTED ON AUGUST 16, 2016 UPDATED ON AUGUST 16, 2016
9 Votes

Questions Answers Related to Codes & standard: –

1. Q:-What is the ASME code followed for design of piping systems in Process piping
(Refineries
& Chemical Industries)?
(i) B 31.1
(ii) B 31.3
(iii) B 31.5
(iv) B 31.9
Answer (II)
2. Q:-Which American institute standard does piping engineer refer?
Answer: –
A. The American Petroleum institute (API).
B. The American Iron & Steel institute (AISI).
C. The American Society for Testing and materials (ASTM).
D. The American National standard institute (AISI).
E. The American welding society (AWS).
F. The American Water Works Association (AWWA).
G. The American Society for Mechanical Engineers (ASME).
3. Q:-What is the different ASME 31 code for pressure piping?
Answer: –
A. ASME B31.1 – Power piping.
B. ASME B31.2 – Fuel Gas Piping.
C. ASME B31.3 – Process piping.
Piping Related Interview Questions
D. ASME B31.4 – Pipeline Transportation system for liquid hydrocarbon & other liquid.
E. ASME B31.5 – Refrigeration Piping.
F. ASME B31.8 – Gas transmission & distribution piping system.
G. ASME B31.9 – Building services piping.
H. ASME B31.11 – Slurry transportation piping system.
4. Q:-What are the different sections of ASME code? Where these sections are referred?
Answer: –
A. ASME section I : – Rules for construction of power boiler.
B. ASME Section II : – Materials.
Part A – Ferrous materials.
Part B – Non-Ferrous materials.
Part C – Specification for electrodes & filler wire.
Part D – Properties.
C. ASME Section IV : – Rules for construction of Heating Boiler.
D. ASME Section V : – Non- destructive Examination.
E. ASME Section VI : – Recommended rules for care & operation of heating boiler.
F. ASME Section VII : – Recommended guidelines for care of power boiler.
H. ASME Section VIII : – Rules for construction of pressure vessels. (Division I & II)
I. ASME Section IX : – Welding & Brazing qualification.
5. Q:-Which American standard is reffered for selection of following piping element?
A. Flanges B. Butt Welded fittings C. Gasket D. Socket & Threaded fittings
E. Valves F. Pipes.
Answer: –
A. Flanges :-
I. ASME B16.1 : – Cast iron pipes flanges & flanged fittings.
II. ASME B16.5 : – Carbon steel pipes flanges & flanged fittings. (Up to 24”)
III. ASME B16.47 : – Large Diameter steel flanges. (Above 24”)
B. Butt welded fittings :-
I. ASME B16.9 : – Steel butt welding fittings.
II. ASME B16.28 : – Butt-welded short radius elbows & returns bends.
C. Gasket :-
I. ASME B16.20 / API -601: – Metallic gaskets for pipe flanges- Spiral wound,
Octagonal ring Joint & Jacketed flanges.
II. ASME B16.21 : – Non metallic gasket.
D. Socket & Threaded fittings :
I. ASME B16.11 : – Forged steel socket welding & threaded fittings.
E. Valves :-
I. ASME B16.10 : – Face to face & end to end dimension of valves.
II. ASME B16.34 : – Flanged & butt-welded ends steel valves (Pressure &Temperature
ratings)
except Ball, Plug & Butter fly Valves.
F. Pipes :-
I. ASME B36.10 : – Welded & Seamless wrought iron pipes.
Piping Related Interview Questions
II. ASME B36.19 : – Stainless steel pipes.
Take Free Practice Test AWS CWI
If you are Interested to attend our AWS CWI Seminar, Please Fill the Enquiry Form:

Name(required)

Email(required)

Mobile

Location

Comment(required)

Submit

This entry was posted in Piping Interview Questions Answers and tagged 11 most important questions
& answers from ASME B, interview questions on piping projects, pdms piping designer interview
questions, Piping Design Engineer Interview Questions, piping design interview questions and answers
pdf, Piping interview questions, PIPING INTERVIEW QUESTIONS PART 1, piping questionnaire
 Piping Related Interview Questions

pdf, piping questions and answers pdf free download, piping related question and answer, piping
supervisor interview questions and answers, Searches related to Piping Interview Questions Answers
Related to Codes & standard, sp3d piping interview questions, Top 10 piping interview questions with
answers.

Follow us

 VIEW AWS.CWI.TRAINING.COURSE’S PROFILE ON FACEBOOK

 VIEW AWSCWITRAINING’S PROFILE ON TWITTER
 PINTEREST
 YOUTUBE
 VIMEO

Get Details Instantly

Name(required)

Email(required)

Mobile No.(required)

Location:(required)
Piping Related Interview Questions

Comment

Submit

Search

Search for:  

Call US: +918196980555

Puneet Sharma E-mail:- [email protected]

Follow us on Facebook
Follow Us on Twitter
My Tweets

Recent Comments

Ram Ganapathy on Q:- When reviewing a radiograp…

ARUL on Q:- Open corner joint is one o…

 Piping Related Interview Questions

ARUL on Q:- Welding inspection personn…

Mahmood Al-Hinai on Q:- Welding inspection personn…

Densel Galloway on AWS CWI Exam Preparation …

Subscribe to Blog via Email

Enter your email address to subscribe to this blog and receive notifications of new posts
by email.
Join 7,483 other followers
Email Address:
Subscribe
Top Clicks

 aws.org/library/doclib/CW…
 eurotechworld.net/compete…
 aws-cwi-training.blogspot…
 aws.org/library/doclib/22…
 awo.aws.org/2014/09/how-t…
 aws-cwi-training.blogspot…
 awo.aws.org
 eurotechworld.net/welding…

Contact Info
BUNGLOW NO 175
Sector 4 CHARKOP
BEHIND CHARKOP BUS DEPOT
KANDIVALI WEST
MUMBAI 67
INDIA, MUMBAI, CHENNAI, AHMEDABAD, NEW DELHI

+918196980555
 Piping Related Interview Questions

Blog Stats

 240,040 hits

AWS CWI CERTIFICATION SEMINAR IN COIMBATORE

AWS CWI EXAM PREPARATION QUESTIONS
AWS CWI SCHEDULE AHMEDABAD GUJARAT 2016
AWS CWI SCHEDULE MUMBAI 2016
AWS CWI TRAINING & EXAM IN CHENNAI
AWS CWI TRAINING SCHEDULE CHENNAI
AWS CWI TRAINING IN AHMEDABAD
AWS CWI TRAINING EXAM SCHEDULE AHMEDABAD 2015
AWS CWI TRAINING IN DELHI
AWS CWI TRAINING IN MUMBAI
AWS CWI TRAINING SCHEDULE CHENNAI 2016
AWS CWI TRAINING SCHEDULE DELHI 2016
AWS CWI-CERTIFICATION/SEMINAR SCHEDULES INDIA 2016
HOW TO RENEWAL YOUR AWS CWI CERTIFICATE?
PLAN YOUR CAREER WITH AWS CWI CERTIFICATION
TAKE FREE AWS-CWI PRACTICE TEST

WE TEAMED UP WITH EVENTBRITE

 Follow

Close and accept

Privacy & Cookies: This site uses cookies. By continuing to use this website, you agree to their use.
To find out more, including how to control cookies, see here: Cookie Policy

Popular Interview Questions

 AJAX Interview questions

 Angular 4 Interview Questions
 Android Interview Questions
 Azure B2C Interview questions
 AWS Interview Questions
 Banking Interview questions
 Bioinformatics Interview questions
 Blockchain Interview questions
 Blue Prism Interview Questions
 Bootstrap 4 Interview questions
 Business administration Interview questions
 Business Analyst Interview questions
 Business Finance Interview questions
 Chartered accountant Interview questions
 Data analyst Interview questions
 Data science Interview questions
 Database Interview questions
 EMC Interview questions
 DevOps Interview Questions
 Ethernet Interview questions
 Ethical Hacking Interview questions
 ERP Tools Interview questions
 ETL Testing Interview Questions
 Finance Interview questions
 GitHub Interview questions
 Hadoop Interview Questions
 Housekeeping Interview questions
 HTML 5 Interview questions
 IBM Cognos Interview questions
 Interior Designing Interview questions
 Insurance Interview questions
 Inventory planning Interview questions
 Java Interview Questions
 Jenkins Interview Questions
 JMeter Interview Questions
 Joomla Interview Questions
 Legal Interview questions
 Linux Interview questions
 Marketing Interview questions
 Maven Interview Questions
 MongoDB Interview Questions
 MSBI Interview Questions
 Pharmacology Interview questions
 PHP+MySQL Interview Questions
 PL/SQL Interview Questions
 Project Management Interview questions
 Python Interview Questions
 Quality Analyst Interview questions
 ReactJS Interview questions
 RF Engineer Interview questions
 Ruby Interview questions
 Sailing Interview questions
 Sales Interview questions
 SAP FICO Interview questions
 Sap Hybris Interview Questions
 Services Marketing Interview questions
 Soap UI Interview Questions
 Solaris Interview questions
 Solid Works Interview questions
 Staffing Interview questions
 Tally Interview questions
 Tele Sales Interview questions
 Telemarketing Interview questions
 Ui Path Interview questions
 VLSI Interview questions
 VMware Interview questions
 XPath Interview questions
All Interview Questions
All Practice Tests
List of Tutorials
 Developers Best Practices Tutorial 
 YAML Tutorial 
 Salesforce Tutorial 
 Adobe Robohelp Tutorial
 Sublime Text Tutorial
 GItlab Tutorial
 Adobe InDesign CC Tutorial
 SaltStack Tutorial
Read More
List of Topics
 Summary 
 Career Planning in best practice  
 Managing Managers 
 Stress Management 
 Eager to Learn
 Handy Tools & Techniques
 Keep the Assets Safely
 Testing is the Religion
Read More
Interview Questions
 Ravendb Interview Questions 
 Cobertura Interview Questions 
 Java Quartz Interview Questions 
 Cheque Truncation System Interview Questions  
 ECS Interview Questions 
 RTGS Interview Questions
 Private Equity Interview Questions
 Excel Formulas Interview Questions
Read More

 Login / Signup Are you an Employer? 

 HOME
 

 JOBS 
 

 JOBS BY COMPANIES 
 

 JOBS BY LOCATIONS 
 

 GOVT JOBS
 

 WALKIN JOBS
 

 ASSESSMENTS
 

 TUTORIALS
 
 SERVICES
 

 CAREER EDGE

 ABOUT US
 About Wisdom Jobs
 Contact US
 Privacy Policy
 Terms of Use
 Disclaimer
 Report a problem
 Help
 Press Corner
 Html site Map
 TOP COMPANY JOBS
 HDFC Careers
 Infosys Careers
 Mphasis Careers
 Axis Bank Careers
 Ashok Leyland Careers
 AEGIS Careers
 Convergys Careers
 Adobe Careers
 ICICI Bank Careers
 Indigo Careers
 Spicejet Careers
 HSBC Careers
 TOP CATEGORY JOBS
 Govt Jobs
 Freshers world
 Today walkins
 Sarkari Result
 Agriculture Jobs
 Defence Jobs
 NGO Jobs
 Real Estate Jobs
 Shipping Jobs
 Java Jobs
 Education Jobs
 Journalism Jobs
 SAP Jobs
 IT Software Jobs
 JOBS IN TOP LOCATIONS
 Jobs in Delhi
 Jobs in Bangalore
 Jobs in Mumbai
 Jobs in Pune
 Jobs in Chennai
 Jobs in Hyderabad
 Jobs in Kolkata
 Jobs in Chandigarh
 Jobs in Gurgaon
 Jobs in Noida
 Jobs in Ahmedabad
 Browse All Jobs
 ASSESSMENTS
 Pragnya Meter
 TUTORIALS
 E-University
 Skill Sets
 Practice Tests
 SERVICES
 Resume Writing
 Profile Enhancement
 Recruiter Reach
 JOB SEEKER
 Register Now
 RECRUITERS
 Post an alert
 Resume Search
 RESOURCES
 Career Edge
 Job Posting Guide
 Free Job Alerts

 Our Portals :
 Gulf Jobs
 Canada Jobs
 USA Jobs
 Italy Jobs
 UK Jobs
 South Africa Jobs
 Malaysia Jobs
 Singapore Jobs
 Australia Jobs
 New Zealand Jobs
All rights reserved © 2020 Wisdom IT Services India Pvt. Ltd