20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

Aprimorado/Dual Powered
Programador Willem EPROM
Guia de usuario  
 

Imagem do item do pacote Willem

Lista de ICs suportados

Instalação e configuração

Configuração do jumper

Função de autoteste

Interface de software

Programação de chip FLASH

Programação de Chip EPROM

Programação de Chip EEPROM

Programação de Chip ATMEL

Programação de chip PIC

Programação de Chip AVR

Adaptador ATMEL AT89

Adaptador ATMEL PLCC44

Adaptador TSOP48

Imagem do item do pacote Willem  

Placa Principal / Cabos

Placa Principal PCB3.5

Placa principal PCB4E

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 1/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide
Placa Principal PCB5.0

 
Placa principal PCB5.5C

Cabo de dados paralelo (cabo de extensão da impressora, com conector macho-fêmea de 25 pinos e pino Cabo USB tipo AA (para
a pino) alimentação)

                                

          

Itens Opcionais:

Adaptador ATMEL 89 Adaptador ATMEL PLCC 44 Adaptador TSOP 48

Adaptador FWH/HUB PLCC32 Adaptador PLCC32 Adaptador SOIC (simplificado)

A bordo A bordo

AC or DC Power Adapter (9V or 12V, 200mA) SOIC Adapter(Professional)  

 

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 2/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

Supported Device List

 
Memory/MCU Model #

27C16, 27C32,27C64,27C128, 27C256,27C512,27C010,27C020, 27C040, 27C1001

EPROM M27C1001,M27C2001, M27C4001
(Not include 13.5V Vpp chip)
27C080,M27C801,M87C257
2716(Vpp25V), 2732, 2764, 27128, 27256, 27512, 27010

27C1024 (27C210), 27C2048 (27C2002), 27C4096 (27C4002)

16 bit EPROM(DIP40) (1-4Mbit)
Eprom 16bit DIP40 adaptor is needed

M27C400(DIP40), 27C800, 27C160, 27C322

16 bit EPROM(DIP42) (4-32Mbit)
Eprom 16bit DIP42 adaptor is needed

W27E512, W27E010, W27C010, W27C020, W27C040

SST27SF256, SST27SF512, SST27SF010, SST27SF020
Erasable EPROM
MX26C4000
Vcc = 3.3-3.6V SST37VF512, SST37VF010, SST37VF020, SST37VF040
28C65, 28C64, 28C128, 28C256, 28C512, 28C010, 28C020, 28C040
M28C16A/17A (DIP28)
EEPROM
28C16, XLS2816 (DIP24)
AT28C64B, AT28C256, AT28C512, AT28C010, AT28C020, AT28C040
28F64, 28F128, 28F256, 28F512, 28F010, 28F020
MX26C1000, MX26C2000, MX28F1000, MX28F2000
Am28F256A, Am28F512A, Am28F010A, Am28F020A
intel:
i28F001BX, 28F004, 28F008, 28F016
SST28SF040A, LE28F4001
29F64, 29F128,  29F256, 29F512, 29F010, 29F020, 29F040, 29F080
29F001,29F002, 29F004, 29F008, 29F016, 29F032
FLASH Memory AT29C256, AT29C512, AT29C010A, AT29C020, AT29C040, AT29C040A
W29EE512, W29EE011, W29EE012, W29C020(128),W29C040
PH29EE010(W29EE011)
ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020)
AT49F512, AT49F010, AT49F020, AT49F040
SST39SF010, SST3S9F020, SST39SF040
AT49F001, AT49F002, AT49F008A
Am29F512, Am29F010, Am29F020, Am29F040.HY29F080
29F002, 29F002T, Pm29F002T
Am29F400, Am29F800, 29F160, 29F320 (read/write byte mode)
with TSOP48 Adapter:
HY29F200, HY29F400, HY29F800, AT49F2048A, AT49F4096A,  AT49F8192A

i28F200,i28F400, i28F800, i28F160 (TSOP48)

with TSOP48 Adapter (Vpp12V):
28F001(DIP32 or PLCC32)

with TSOP48LV Adapter: 29LV200, 29LV400, 29LV800, 29LV160, 29LV320 (read/write byte mode)

Firmware Hub:
82802AB, 82802AC, AT49LW040, AT49LW080
with Firmware Hub/LPC (PLCC32) adapter SST49LF002A, SST49LF003A, SST49LF004A, SST49LF008A
LPC flash:
SST49LF020, SST49LF040
24C02, 24C04, 24C08, 24C16, 85C72, 85C82, 85C92
Serial (I2C)EEPROM 24C32, 24C64, 24C128, 24C256, 24C512 (allC/LC series)
PCF8572,8572, PCF8582, 8582, PCF8592, 8592
8 mode:93C06, 93C46, 93LC46, 93C56, 93C57,
93C66, 93C76, 93C86,93C13,93C14
Microwire EEPROM 16 mode:AT59C11, AT59C22, AT59C13
CAT35C102, CAT35C104, CAT35C108
93C06A ,93C46X,93C56,93C66,93C76,93C86 (NS)

PIC embedded MCU 16C5X,17XXX,18XXX series

12C508,12C508A,12C509,12C509A 12CE518,12CE519 12C671,12C672,12CE673,12CE674 16C505 16C61,16C620,16C621,16C622A

with PIC embedded MCU  adapter: 16F627,16F628,16C71,16C715 16C84,16F83,16F84,16F84A 16C64A,16C65A,16C65B,16C67 16C74A,16C74B,16C77
16F871,16F874,16F877 16C62A,16C62B,16C63,16C63A,16C66 16C72,16C72A,16C73A,16C73B,16C76 16F870,16F872,16F873,16F876

SPI EEPROM Atmel:AT25010,020, 040 (A8-A0)

AT25080, 160, 320, 640, 128, 256 (A15-A0)
ST:W95010....256, Microchip 25x010 - 25x640
25010,25020,25040
25C080,25C160,25C320,25C640,25C128,25C256,25C512
AT25HP256,AT25HP512
https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 3/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide
AT25HP1024
CAT64LCxxx (16 Data I/O)
CAT64LC010, CAT64LC020, CAT64LC040
DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB
Test SRAM,Lossless SRAM Function
6116, 6264, 62256, 62512, 628128
89 series:
Atmel:AT89C51,52,55, AT89LV51,52,55
AT89S8252 (8K+2K), AT89S53, AT89LS8252,AT89LS53
AT89C1051,AT89C2051,AT89C4051 (20pin)
Embedded MCU AT89C51RC (32KB), AT89C55WD (6.2V)
with Atmel AT89 dapter SST89C54/58, SI89C52
Intel:i87C51, i87C51FA, i87C51FB
i8xC51,i8xC52,i8xC54,i8xC58

90 series:

AT90S1200,AT90S2313
89 series:
Atmel:AT89C51,52,55, AT89LV51,52,55
AT89S8252 (8K+2K), AT89S53, AT89LS8252,AT89LS53
AT89C1051,AT89C2051,AT89C4051 (20pin)
AT89C51RC (32KB), AT89C55WD (6.2V)
Embedded MCU with 51-AVR+ dapter SST89C54/58, SI89C52
Intel:i87C51, i87C51FA, i87C51FB
i8xC51,i8xC52,i8xC54,i8xC58

90 series:

AT90S1200,AT90S2313

90S2333, 90S4433, 90S4414, 90S8515, 90S4434, 90S8535,AT90S2313

P8048AH, P8049AH,P8050AH, P8042AH (Vea = 12V)

P8041, P8042
with Atmel AT89 PLCC44 OTP (read/verify/Progam)
adapter P8748,P8749H,P8742H(Vea = 18V)
EPROM (read/verify/Progam)
D8748,D8749,D8742,D8741, D8742(Vea = 18V)

Hardware Installation & Configuration

Installation Steps
  

Check the parallel printer port setting in the bios, it should be EPP or Normal.
Check there are any active resident programs that use the printer port, such as TWAIN drivers. You may have to remove it.
Connect one end of the 25 pin SubD parallel cable  to PC printer port
Connect the other end  of parallel cable to 25 Pins port of the programmer
Connect USB power cable or AC adaptor (Note: if you are working on the EPROM programming. You may need use a AC adaptor, so that you can get Vcc 5.6V and 6.2V when
doing programming)
The yellow power normal indicator of the programmer should light up, then the programmer power supply is normal.
Run the software
Select devices type
Click the Willem in toolbar to change to PCB3
Set the DIP switch based on the displayed pattern.

          (Note: the LPT port of PC MUST set to ECP or ECP+EPP during BIOS setup. To enter the BIOS setting mode, you need press "Del" key or "F1" key during the computer selftest,
which is the moment of computer just power up.)

Software Version To Use

The software can be download from download.mcumall.com  

There are board hardware selection jumper on the board. When set the jumper to PCB3B, then user have to use 0.97ja and before version software.

If the board selection set to PCB3.5, PCB5.0, PCB5.5C, then the software 0.98D6 should be used.

 
          The software interface:

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 4/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

Hardware Check

After start the program, click test hardwar under Help menu. If the connection and power supply is normal, then appears: "Hardware present"   Otherwise check if the programmer connects well
with PC, or power supply is normal.

 
Jumper Configuration
 

PCB3.5/PCB4E

(Two PLCC32 adapter is not applied on the PCB4E)

PCB5.0

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 5/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

PCB5.5C
 

Note: the Vcc setting jumper only has effect when you are using AC adaptor as power source. For the USB power only 5V Vcc is available.

For the PCB5.5C, set DIP steps:

1. press DIP Set button twice to check current DIP bit position. Then set it again for ON or OFF.

2. press DIP Bit shift button to shift the DIP bit position to where need to set. And then press DIP Set button twice to check current DIP bit position. Then set
it again for ON or OFF.

3. Repeat those steps till all DIP bit ae set  same as software indicated.

For PCB5.5C voltage and Special chip selection:

1. Put back the safety jumper.

2. Press the voltage button and hold for 1 second, the voltage LED should move to next. Repeat till desired voltage LED light up.

3. Press the chip selection button and hold for 1 second, the chip LED should move to next. Repeat till desired LED light up.

4. Remove the safety jumper to lock the selected voltage and chip selection

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 6/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide
 
DIP Switch (PCB3.5, PCB5.0)

When programming one chip,  follow the program prompt to set DIP switch . 

Self Test Function 

The screen :

   
Steps:

Before test, set the DIP switch, jumper setup to software prompted
Address Pin Test: click the one of the push button in the Address Out group, use multimeter detect output signal in the ZIF32 socket. Or directly input the adress data, the range is:0-
-7FFFFH A0-PIN 12, A1-PIN 11, A2-PIN 12, A3-PIN 9, A4-PIN 8, A5-PIN 7, A6-PIN 6, A7-PIN 5, A8-PIN 27, A9-PIN 26,A10-PIN 23, A11-PIN 25, A12-PIN 4, A13-PIN 28,
A14-PIN 29,A15-PIN 3, A16-PIN 2, A17-PIN 30
Data Pin Test: click one of the push button in Data Out group, use multimeter confirm the data from ZIF socket. Alternatively, input the test data, the range is: 0--FFH; D0-PIN 13,
D1-PIN 14, D2-PIN 15, D3-PIN 17, D4-PIN 18, D5-PIN 19, D6-PIN 20, D7-PIN 21
VPP (programming voltage) Test: Turn on the programming voltage by click on pin 1 (1-Vpp) check box, measure the voltage between PIN 16 and PIN 1. It should show the Vpp
voltage your set. (12V, 15V, 21V, 25V. Note : there mybe  0.5V tolerance of voltage reading)
Clear All: Clear the whole control signal, address and data output. Then you measure should be all 0V.

Software Interface & Function

 

The software interface :

 
Tool bar:

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 7/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

  Read data file to buffer, it can be : Intel HEX (*.hex); Binary (*.bin); Motorola S Record (*.s); ALL Eprom File (*.bin, *.hex, *.s)

  Save data to a file from buffer

 Clear buffer of programmer software

  Read data from chip to programmer buffer

 Blank verify. Verify the chip if it is blank

 Display chip's factory ID

 Programming/Test. Programm the chip or test the SRAM.

 Erase. Erase content of chip.

 Programming bit control. For MCS51, AVR

 

 
File : Open, Save, Exit.

Edit: Edit buffer

Device: Selection
of target device/chip.

Action: The operations for the taget device/chip.

Help: Help infomation.

Main area in software: From left to right there are four sections
1, chip selection and parameterrea
2, hardware jumper and setting indication picture.
3, MCU chip's parameter setting,  such as lock bit.
4, programming parameter setting and fine adjustment. Normally a default value can be used.

 
Tab page selection:

The bottom of main program screen is series tab window button.

 

 
Click "Buffer" button,display buffer content. The first column of data is data address, last column is the data ASCII code, the middle is data hex value. If internal EEPROM exists in
PIC MCU, the EEPROM data content displays automatically.
 
Status bar : Displays programmer's current status: the chip write in is not correct, wrong programming position, programmer problem and so on.

BIOS/Flash Setting & Programming

Programming the BIOS on Willem programmer is easy, as long as we selected right chip type and right
jumper. Here is an example for programming on a N82802AB of Intel845 mother board(3.3V):

 
1, select chip type and software setting

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 8/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

 
now you can see following setting:

      DIP position: OFF,ON,ON,OFF,ON,ON,OFF,ON,OFF,ON,OFF,ON

parameters are no need to adjusted, using default value.
Chip's parameter is showed below the Chip  Select  Button. Normaly, those
Size&checksum:  shows chip's capacity and data buffer's checksum.

address bit.
Shift&pattem adress: shows chip's address line to be used and highest
tWP/WC: shows programming  pulse width and delay time.

 
2. check chip's position

  After DIP set, check the chip's position. For BIOS chip, it should be placed in the 32 pins ZIF socket. For N82802AB chip, the program prompt user need a FWH/LPC adaptor.

Please make sure the pin one position on the FWH/LPC adaptor.
   
  Note: 1,Displayed chip's parameter is no need to be ajusted.
        2, DIP is different when programming different chip

chip and special valtage follow the prompt of software.
        3, For EPROM chip, we need resetting the DIP, speicial
 
3, read from chip

After selected the chip, we can click on the "Read" button. All data will be put into the buffer.

When reading the chip, the yellow LED will be light up, indicats that the valtage is been applied on the chip.

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 9/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide
4, Programming

  After insert the chip, click on "Open file" to open your data file. Then click on "Programm Chip" button.  Note,  some of chip  need erase before write.
  When programming, the yellow LED will be on. If the chip need a Vpp programming voltage, the red LED will be on.

5, copy a chip:
  1), Select the
chip type and then put in the original chip. 

  2), "read" the data into buffer.

   3), Put in the target chip and then click "Programm Chip".
 
Note: the chip may be damaged if wrong chip type selectd or chip in a wrong direction in socket.
 
 The following parameter is for advanced user only.

R/C delay time: programming pulse delay. If your computer is too fast, you may need increase the delay.

Skip Write 0xFF: Enable this setting will skip the 0xFF when programming.
Fast Programming: For a fast programming mode if it is enabled.

Printer Port:  LPT1(0X378), printer port selected.

Offset: setting programming start offset affress.

Check Type: You can select the way to check  either 32 bit CRC or 16 bit add.

Note:
1, some of chip need to be erased in order to programming. Such as SST39SF020.
2  Always put the chip in the programmer at the last step. Because the programmer is in a unstable state then
windows is starting.
3, Do not interrupt the programming procedure. Press the "Stop" button if needed.

EPROM Chip Programming

The operation to EPROM chip is similar to general BIOS chip. The main diffrence is: the programmer jumper needs relevant ground setup. As an example: write a
27C16(programming voltage is 12.5V), also you need change the Vcc voltage setting accordingly. Some chips need the Vcc set to 6.2V when doing programming.
 
1. Select the chip and configuration

Set the chip and make sure the jumper for that chip is correct , the program displays the DIP switch setting. Follow the figure to set up the DIP switch, includes the jumper next to
DIP switch.

 
The DIP switch setup is: toward to upper side is on, toward to bottom side is off. As to above figure, the DIP switch is: ON, ON, OFF, OFF, OFF, ON, OFF, ON, ON, OFF, OFF,
OFF.

 
2. Fix the chip position

After DIP switch set-up, insert the chip to 32 PIN ZIF socket, check the special chip
 
setting is correct. 
 

For the chips have capacity less than 1M, PIN fewer than 32 PIN, the chip installation is
shown the right figure, align with the bottom of ZIF socket:

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 10/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide
The follows operation is read in data file, programming. When programming, the red indicator lights up. This shows the programmer has corect voltage Vpp.

 
Note:if wrongly selected the chip type, the EPROM chip may be damaged.

 
EEPROM Chip Programming
Some EPROM chip, like W27C512 or W27C512,they are 27series, but no erasing window on the top. Then, they have to be erased electronically. When programming this type,
besides the DIP setup and insert tion of IC to 32 PIN ZIP socket, the special chip and special voltage button have to be adjusted accordingly.
 
1. WinBond EEPROM
The programmer supports: W27E512,W27E010,W27C010,W27C020,W27C040
Operation steps: 

1) Setup the 12 bit DIP, select the chip model W27CXX

2) Set the programming voltage VPP to 15V, special model jumper to W27C position
3) Insert W27CXX to 32PIN ZIP socket, click the software upper right corner erase button, the program indicator lamp flashs and progress bar is not moving, then directly press
reset button, the chip starts to erase. 
4) Verify the result.
 

2. SST EEPROM
This programmer supports: 27SF256, 512, 010, 020, 040;37VF512, 010, 020, 040.
Operation steps (Vpp keeps as 12V):

1) Setup the 12 bit DIP, select the chip model W27CXX

2) Set the programming voltage VPP auto to 15V, special chip jumper to W27C position.
3) Insert W27CXX to 32PIN ZIP socket, click the software upper right corner erase button, the program indicator lamp flashs and progress bar is not moving, then directly press
reset button, the chip starts to erase.
4) Verify the result.
 

3. MX26C4000 EEPROM
Operation steps (VPP keeps as 12V):

1) Setup the 12 bit DIP, select the chip model W27CXX

2) Set the programming voltage VPP to 15V, special model jumper to W27C position.
3) Insert W27CXX to 32PIN ZIP socket, click the software upper right corner erase button, the program indicator lamp flashs and progress bar is not moving, then directly press
reset button, the chip starts to erase.
4) Verify te result.

ATMEL Chip Programming

 

Select the target MCU chip, the program prompts the relevant adapter. Meanwhile, dispaly the options to select the lock bit:

 
 
MCS-51encryption setup, lock bit functions:
No LockBit:no

MOVC instruction and programming again. 
LockBit1:forbiden

LockBit1+2:include the above functions and forbiden test (forbiden readout FLASH)
LockBit1+2+3:include the above functions and forbiden external program memory

PIC Chip Programming

 

After select the relevant PIC chip type, the program prompts the needed socket:

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 11/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

 
Meanwhile, in the chip setup area, display the relevant setup to select PIC MCU configuration parameters

 
PIC MCU configuration parameters:
Oscillator types: 

LP:low power consumption

XT:crystal/ceramic

HS:high speed crystal/ceramic

RC:resistance

IntRC:internal
4Mhz resistant 
ExtRC:external resistant

ExtClock:external clock(24Mhz)
E4:external clock with PLL(6Mhz)

H4:crystal/ceramic with PLL(6Mhz)

IntRC RB4:internal resistant

IntRC CLKOUT:internal resistant,RB4 output clock ExtRC RB4:external resistant

ExtRC CLKOUT:external resistant,RB4 output clock 

IntRC I/O:internal resistant 

intRC CLKOUT:internal resistant, output clock

ER I/O:external resistance

ER CLKOUT:external resistance,output clock 

Code protect:encrypt PIC MCU program, prevent read out
Watch Dog:turn on/off watch dog

Power-up Time:upper power delay selection

AVR Chip Programming

 

As to AVR chip, choose the target chip,the program prompts the correct adapter socket.
 
Meanwhile, at the chip configuration area, display the right setup list in order to choose PIC MCU configuration parameters.

CKSEL0...2:Reset delay selection

BODEN:BOD(power off test)permission

BODENLEVEL:BOD strike voltage selection

FSTRT:upper start time selection

RCEN:internal RC oscillation permission

SPIEN:SPI serial programming permission

ATMEL89 Adapter

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 12/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

By using this adapter, it is able to program MCS-51 series MCU. The MCU includes ATMEL & INTEL.

It supports: 

89 series MCU: 
AT89C1051,AT89C2051,AT89C4051,AT89C51,AT89LV51,AT89C52,AT89LV52,AT89C55,AT89LV55,AT89S8252,AT89LS8252,AT89S53,AT89LS53
AT87F51,AT87F52 i87C51,i87C51FA,i87C51FB,i87C51FC,i87C52,i87C54,i87C58 (*)AT89C51RC (32KB), AT89C55WD
90 series AVR 8-bit RISC: AT90S1200,AT90S2313

 
Other AVR chips need 51-AVR+ adator, such as 90S2333, 90S4433, 90S4414,90S8515, 90S4434, 90S8535

ATMEL PLCC44 Adapter

 

This adaptor is able to program  MCS-51 series PLCC MCU, such as 89C51PLCC44. Please note, it is used with ATMEL89 Adapor.

TSOP48 Adapter

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 13/14
20/11/2022 15:17 Standard PCB3B Willem Programmer User Guide

This adaptor is able to program  TSOP48 flash chip. More details please see supported device list.  The default jumper setting on the base board is above. Please change it as needed. 
JP2 jumper keep it close normorlly. It will increase the compatibility betwwen the similar device . Only try to open it for some chip if programming fail. The JP2 jumper is not in the
original design and it also not documented for the most of chip.

Bellow is the TSOP48 adaptor on board, please reffer to jumper setting section for A19 and A20 connection:

https://www.mcumall.com/support/DualPoweredWillemUserGuide.htm 14/14