Product Data

HEMPADUR MASTIC 45881

High temperatures 45881: BASE 45889: CURING AGENT 95881

Description: HEMPADUR MASTIC 45881 is a two-component polyamide adduct cured, high solids, high build epoxy
paint. It forms a hard and tough coating, has good wetting properties.
Recommended use: As a selfprimed, surface tolerant paint system or as an intermediate or finishing coat in heavy duty
paint systems where low VOC and high film build are required.
For immersed areas HEMPADUR MASTIC 45881 is only recommended for minor repairs.
Can be specified where extended recoating properties for polyurethane topcoats are requested
(typically travel coating). May be used directly on cured zinc silicate (GALVOSIL products) or spray-
metallized surfaces to minimize popping.
Service temperature: Maximum, dry exposure only: 120°C/248°F
Certificates/Approvals: In accordance with Aramco’s specification APCS 1, APCS 12, APCS 26 and 26T.
Tested according to section 175.300 of the Code of Federal Regulations Title 21 - Dry Foodstuff.

Tested for non-contamination of grain cargo at the Newcastle Occupational Health & Hygiene, Great
Britain.
Approved as a low flame spread material when used as part of a predefined paint system. Please refer
to “Declaration of Conformity” on www.Hempel.com for further details.
Complies with EU Directive 2004/42/EC: subcategory j.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 12170* / Grey. (see REMARKS overleaf)
Finish: Semi-gloss
Volume solids, %: 80 ± 1
Theoretical spreading rate: 6.4 m2/l [256.6 sq.ft./US gallon] - 125 micron/5 mils
Flash point: 35 °C [95 °F]
Specific gravity: 1.5 kg/litre [12.1 lbs/US gallon]
Dry to touch: 3 hour(s) 30°C/86°F
Fully cured: 5 day(s) 30°C/86°F
VOC content: 218 g/l [1.8 lbs/US gallon]
Shelf life: 3 years for BASE and 3 years (25°C/77°F) for CURING AGENT from time of production.
- *Wide range of colours available via Hempel's MULTI-TINT system.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

APPLICATION DETAILS:
Version, mixed product: 45881
Mixing ratio: BASE 45889: CURING AGENT 95881
3 : 1 by volume
Application method: Airless spray / Brush
Thinner (max.vol.): < 5% HEMPEL'S THINNER 08450, depending on purpose (see REMARKS overleaf)
Pot life (Airless spray): 1.5 hour(s) 30°C/86°F
Pot life (Brush): 2 hour(s) 30°C/86°F
Nozzle orifice: 0.017 - 0.023 " According to separate APPLICATION INSTRUCTIONS
Nozzle pressure: 250 bar [3625 psi]
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 125 micron [5 mils] see REMARKS overleaf
Indicated film thickness, wet: 150 micron [6 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-

Date of issue: June 2016 Page: 1/3

Product Data
HEMPADUR MASTIC 45881

SURFACE PREPARATION: New steel: Abrasive blasting to minimum Sa 2½ (ISO 8501-1:2007) with a surface profile
corresponding to Rugotest No. 3, N9a to N10, preferably BN9a to BN10, Keane-Tator Comparator, 2.0
G/S or ISO Comparator, Medium (G).
Zinc silicate painted or spray-metallized surfaces: Remove oil and grease, etc. with suitable
detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Zinc salts
(white rust) must be removed by high pressure hosing combined with rubbing with a stiff nylon brush if
necessary. It is recommended to recoat spray-metallized surfaces as soon as possible to avoid
possible contamination.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by high
pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and uniform
surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid etching. Seal
surface with suitable sealer, as per relevant painting specification.
Repair and maintenance: Remove oil and grease etc. thoroughly with suitable detergent. Remove
salts and other contaminants by high pressure fresh water cleaning. Clean damaged areas thoroughly
by power tool cleaning to minimum St 2 (spot-repairs) or by abrasive blasting to min. Sa 2, preferably to
Sa 2½ (ISO 8501-1:1988). Improved surface preparation will improve the performance of the product.
As an alternative to dry cleaning, water jetting to sound, well adhering coat and/or to steel. Intact coat
must appear with roughened surface after the water jetting. By water jetting to steel, cleanliness shall
be: Wa 2 -Wa 2½ (atmospheric exposure) / minimum Wa 2½ (immersion) (ISO 8501-4:2006). Feather
edges to sound and intact areas. Dust off residues. Touch up to full film thickness. On pit-corroded
surfaces, excessive amounts of salt residues may call for high pressure water jetting, wet abrasive
blasting or, alternatively, dry abrasive blasting, high pressure fresh water hosting, drying, and finally dry
abrasive blasting again.
APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Use only where application and curing can proceed at temperatures above: 15°C/59°F.
The temperature of paint itself should be 15°C/59°F or above. In confined spaces provide adequate
ventilation during application and drying.
PRECEDING COAT: None, or as per specification.
SUBSEQUENT COAT: None, or as per specification.
REMARKS:
VOC - EU Directive 2004/42/EC:
Not available.
Product As supplied 5 vol. % thinning Limit phase II, 2010
4588112170 218 g/l 250 g/l 500 g/l
For VOC of other shades, please refer to Safety Data Sheet.
Weathering/service temperatures: The natural tendency of epoxy coatings to chalk in outdoor exposure and to become more sensitive to
mechanical damage and chemical exposure at elevated temperatures is also reflected in this product.
Application(s): Application onto zinc silicate or spray-metallized surfaces (thinning): It is recommended to apply the
paint by using a "mist-coat" procedure provided the paint temperature is approximately above:
20°C/68°F. A thin, undiluted coat is applied (the mist coat) and after a few minutes, a second coat is
applied in the full specified film thickness. If the paint temperature is below: 20°C/68°F, thinning (max
15%) may be required.
Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
100-200 micron/4-8 mils. May be specified in lower film thickness for which purpose additional thinning
is required, please see separate APPLICATION INSTRUCTIONS. Avoid application of excessive
film thicknesses.
Shades: The product is also available in a Micaceous Iron Oxide (MIO) pigmented shade (Shade no. 12430 –
reddish grey).
This product is available in several aluminium pigmented shades with different volume solids content.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.

A specification supersedes any guideline overcoat intervals indicated in the table.

Environment Atmospheric, medium
Surface temperature: 20°C (68°F) 30°C (86°F) 40°C (104°F)
Min Max Min Max Min Max
HEMPADUR 7h Ext. 6h Ext. 4h Ext.
HEMPATEX 5h 16 h 4h 12 h 3h 8h
HEMPATHANE 7h Ext. 6h Ext. 4h Ext.
Environment Immersion
HEMPADUR 12 h 30 d 10 h 23 d 7h 15 d
NR = Not Recommended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)

Note: HEMPADUR MASTIC 45881 For professional use only.

ISSUED BY: HEMPEL A/S 4588112170
X Move PDS Disclaimer to Second page

Date of issue: June 2016 Page: 2/3

Product Data
HEMPADUR MASTIC 45881

This Product Data Sheet supersedes those previously issued.

For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.

Date of issue: June 2016 Page: 3/3

Product Data
HEMPATHANE TOPCOAT 55210

55210: BASE 55219: CURING AGENT 95370

Description: HEMPATHANE TOPCOAT 55210 is a two-component, glossy acrylic polyurethane coating, cured with
aliphatic isocyanate, with good gloss and colour retention.
Recommended use: As a finishing coat for protection of structural steel in severely corrosive atmospheric environment,
where light-fastness and gloss retention are required.
Minimum temperature for curing is -10°C/14°F.
Service temperature: Maximum, dry exposure only: 120°C/248°F see REMARKS overleaf
Certificates/Approvals:
Complies with European Fire Standard EN 13501-1; classification B-s1, d0.
Approved as a low flame spread material when used as part of a predefined paint system. Please refer
to “Declaration of Conformity” on www.Hempel.com for further details.
Complies with EU Directive 2004/42/EC: subcategory j.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 10000*/ White.
Finish: Glossy
Volume solids, %: 51 ± 1
Theoretical spreading rate: 10.2 m2/l [409 sq.ft./US gallon] - 50 micron/2 mils
Flash point: 33 °C [91.4 °F]
Specific gravity: 1.2 kg/litre [10.1 lbs/US gallon]
Surface-dry: 1 hour 20°C/68°F
Through-dry: 8 hour(s) 20°C/68°F
Fully cured: 7 day(s) 20°C/68°F
VOC content: 442 g/l [3.7 lbs/US gallon]
Shelf life: 3 years for BASE and 2 years (25°C/77°F) for CURING AGENT from time of production.
- *Wide range of colours available via Hempel's MULTI-TINT system.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

APPLICATION DETAILS:
Version, mixed product: 55210
Mixing ratio: BASE 55219: CURING AGENT 95370
7:1 by volume
Application method: Airless spray / Brush
Thinner (max.vol.): see REMARKS overleaf / 08080 (5%)
Pot life: 4 hour(s) 20°C/68°F
Nozzle orifice: 0.017 - 0.019 "
Nozzle pressure: 150 bar [2175 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S THINNER 08080 or 08510
Indicated film thickness, dry: 50 micron [2 mils] see REMARKS overleaf
Indicated film thickness, wet: 100 micron [4 mils]
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
-
-
-
-
-
-
-
-
-
-
-

Date of issue: August 2016 Page: 1/2

Product Data
HEMPATHANE TOPCOAT 55210

SURFACE PREPARATION: According to specification.

APPLICATION CONDITIONS: Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
Minimum temperature for curing is: -10°C/14°F. At the freezing point and below be aware of the risk of
ice on the surface, which will hinder adhesion. The film formation may be adversely affected by light
rain, high humidity and/or condensation during application and the following interval after application:
10 hours , 20°C/68°F
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: According to specification. Recommended systems are: HEMPADUR45141/45143, HEMPADUR
MASTIC 45880/45881
SUBSEQUENT COAT: None.
REMARKS:
VOC - EU Directive 2004/42/EC:
Not available.
Product As supplied 10 vol. % thinning Limit phase II, 2010
5521010000 442 g/l 483 g/l 500 g/l
For VOC of other shades, please refer to Safety Data Sheet.
Colours/Colour stability: Colour stability for some shades may be effected by exposure to harsh chemical atmospheres. This
does not affect the performance of the coating.
For certain colours extra coats may be necessary to obtain full opacity.

For aluminium pigmented shades scratching actions or high humidity/water may cause discolouration/
disturbances of the surface. This will have no influence on the performance. This phenomenon may be
avoided by applying a clear varnish.
Weathering/service temperatures: At service temperature above 100°C/212°F, slight discolouration may be expected.
Film thicknesses/thinning: The type and amount of thinner depend on application conditions, application method, temperature,
ventilation, and substrate. THINNER 08080 is recommended in general.
Airless spray: 5-10% thinning is recommended. Under extreme conditions up to more than 20% may
be necessary to obtain satisfactory film formation.
Electrostatic spray: 10% thinning is recommended. Contact HEMPEL for more information.
May be specified in another film thickness than indicated depending on purpose and area of use. This
will alter spreading rate and may influence drying time and overcoating interval. Normal range dry is:
40-75 micron/1.6-3 mils.
Shades: This product is available in several aluminium pigmented shades with different volume solids content.
Contact HEMPEL for more information.
Curing agent: CURING AGENT 95370: is sensitive to moisture.
Even small traces of water in the mixed paint will reduce the pot life and result in film defects.
Open curing agent cans with caution as overpressure might exist. Store in a dry place and keep the
can tightly closed until use.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.

A specification supersedes any guideline overcoat intervals indicated in the table.

Environment Atmospheric, medium
Surface temperature: -10°C (14°F) 0°C (32°F) 20°C (68°F)
Min Max Min Max Min Max
HEMPATHANE 30 h None 18 h None 6h None
NR = Not Recommended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)

Note: HEMPATHANE TOPCOAT 55210 For professional use only.

ISSUED BY: HEMPEL A/S 5521010000
X Move PDS Disclaimer to Second page
This Product Data Sheet supersedes those previously issued.
For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.

Date of issue: August 2016 Page: 2/2