DP-A120 USB Interface Kit I-F-42 Installation

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

INSTALLATION MANUAL

DUPRINTER
USB INTERFACE KIT

I/F - 42

Specialized person only


Contact our serviceperson for installation.
To ensure safe operation of the kit, the DUPRINTER
must be installed correctly.
Read these instructions carefully before installing the unit.
Safety Precautions
Warning Terminology
The following warning terminology is used in the DUPRINTER USB INTERFACE KIT installation instructions.

WARNING Indicate a high degree of potential danger. If the warning is ignored, death or
serious injury may result.

CAUTION Indicate a medium degree of potential danger. If the caution is ignored, me-
dium injury or damaged to property may result.

<Examples of Pictorial Symbols>


A circle with a line through it indicates a prohibited action.
The particular act prohibited is indicated by a picture inside the circle.
(In the example shown here, the prohibited act is disassembly.)

◦A black disc indicates an instruction, or sometimes a prohibited action.


The instruction itself is indicated by pictorial symbols drawn in white on the
disc. (In the example shown here, the instruction is ‘Remove the plug from
the outlet.’

● The precautions below are vital for safety and must be taken.

WARNING
● Use only the power cord that is provided among the accessories.
Insert the power cord plug firmly into the socket, so that proper electrical
contact is effected.
→ Use of any other power cord could result in imperfect grounding.
If grounding is imperfect and electrical leakage occurs, fire or electric shock
could result.

● Do not use a source voltage other than that specified.


Do not connect two or more loads to a single outlet.
→ Doing so may result in fire or electric shock.

● Do not place the machine in a humid or dusty area.


→ Doing so may result in fire or electric shock.

Caution
● Do not place the machine in an unstable position, such as on an unsteady
support or sloping area.
→ If the machine is dropped or falls over, this could result in personal injury.

● Once the machine is in position, secure in place using the casters.


→ If the machine falls over, this could result in personal injury.
1. Unpacking Checks

Please confirm the package contents and install them according to the following instructions.

1. Unpack the package.

IMPORTANT
Carry out unpacking in a place
that is safe for the work.

2. Contents checks
Check that the package has the contents listed below.
1 2 3 4

5 6 7 8 9 10 11

12 13 14 Printer Driver Operation Manual for Windows


15
INSTALLATION MANUAL

DUPRINTER
USB INTERFACE KIT

I/F - 42

Specialized person only


Contact our serviceperson for installation.
To ensure safe operation of the kit, the DUPRINTER
Correct operation is essential for ensuring safe use of this machine. must be installed correctly.
Read these instructions carefully before installing the unit.
Thoroughly read this manual before using this machine.
Store this manual so that it can be retrieved whenever needed.

No. Item Part No. Quantity


1 Interface PCB unit J8-V550* 1
2 USB PCB unit - 1
3 Interface cable unit U5-W117* 1
Ferrite core (for Interface cable unit) UJ032 2
4 USB cable unit U5-W117* 1
Ferrite core (for USB cable unit) UT036 1
5 Angle M7-K114* 4
6 FG clamp - 1
7 Banding band - 5
8 Screw (hex-head M4 X 6) (for USB PCB unit) - 2
9 Screw (hex-head M3×6) (for Angle) - 4
10 Screw (M3×6)(for Interface PCB unit) - 4
11 Screw (M4×8) (for FG clamp) - 1
12 Ferrite core UJ032 1
13 Printer driver CD-ROM J8-X130* 1
(Duplo DUPRINTER SETUP SOFTWARE)
14 Printer Driver Operation Manual R8-Y119* 1
15 Installation Manual U5-Y105* 1
* Use USB cable which length is 3m or less. Install the ferrite core on the USB cable.
Refer to the Printer Driver Operation Manual for installation.

1
2. Installing the USB Interface Kit

Please observe the followings when installing 4. Cut out the connector cover from the rear
the USB interface kit to the Duprinter. cover.
Be sure not to get injured with a cutter when
● Install the Duprinter first and then install the you cut out the connector cover.
USB interface kit.
● Make sure that correct screws are used in
correct positions.
● Make sure to remove the power plug on the
Duprinter.

1. Remove the 4 screws to remove the top cover Connector cover


assy.
Screw

5. Install the 4 angles (No. 5) with the 4


screws (No. 9).
Screw

2. Remove the 2 screws to remove the PCB


cover.

6. Install the interface PCB unit (No. 1) with


the 4 screws (No. 10).
Screw

3. Remove the 4 screws to remove the rear


cover.
Screw

7. Install the USB PCB unit (No. 2) with the


2 screws (No. 8).

Screw

2
8. Insert the USB cable unit (No. 4) into the 11. Band the cables of the downloader and
CN6 on the interface PCB unit (No. 1), and Duprinter with the banding band to fix the
CN1 on the USB PCB unit (No. 2) with care connector of the cable unit of the downloader.
for the direction of connector. This cable unit for downloader will not be used
anymore.
CN6 For upgrading, use the connector
for downloader of the interface cable unit.

CN1

9. Insert the interface cable unit (No. 3) into the


CN3, CN11, and CN12 on the interface PCB
unit with care for the direction of connector.
CN11
12. Remove the screw to remove the plate.
Remove the bushing from the frame.

CN12 CN3

10. Disconnect the connector of the cable unit


of the downloader from the J11 on the main 13. Let the opposite side of the interface cable
PCB unit. unit (No. 3) into inside of the Duprinter.
Install the plate with the screw.

J11

14. Insert the connector into the J11 on the


main PCB unit.

J11

3
15. Install the ferrite core on the cable unit of 20. Load B4 paper (high-quality, 128g/m2) on
the downloader removed in step 10 and the the ADF and install the top cover assy so
interface cable unit. that the paper leading edge is parallel to
Place the connector for downloader of the CIS, aligning the document guide with
interface cable unit in the vicinity of the cov- paper width.
er for upgrading.

Ferrite core

Connector for the downloader

16. Install the bushing on the frame.


Band the interface cables with the 4 band-
ing bands (No. 7).

Paper should be parallel to CIS.

21. Load B4 paper (high-quality, 64g/m2) on


the ADF. Access HELP-11 and feed the
document by pressing the MASTER
MAKING key to confirm that the document
17. Install the FG clamp, tucking the metal net is not inserted on a skew.
of the interface cable unit in it.

Install the rear cover when the Duprinter


18. Cut and remove unnecessary part of the 4 setting (adjusting master making position)
banding bands with a tool such as nipper. is completed.

19. Install the removed PCB cover in the


reverse procedure to removing.

4
3. Checking the Operation of Interface Kit

1. Turn on the power to the Duprinter.

2. Load papers in feedable maximum size (B4)


on the feed tray.

3. Switch the DIP-SW No.2 on the interface


PCB unit to ON.

4. Master making will start in approximately 10


seconds and 1 sheets of test pattern will be
printed.

5. If printing is not performed properly, check


that cables and connectors are connected
securely.

6. When printing is performed properly, set the


Duprinter (adjusting master making position).

7. Adjust master making position as below.

* ‘170mm’ is adjusted in HELP-16.


* The center of the paper is adjusted in
HELP-53.

8.

170mm

Center of paper

5
4. Setting the Duprinter (Adjusting master making position)

Correction of master making start position HELP-16 Lengthwise (sub-scanning direction)


while online master making master making start position for online master
• Prepare a computer before adjusting correction of making
master making start position while online master making.
• Please refer to the Printer Driver Operation Manual for 1. Access HELP mode H-16 and press the
the preparation of computer. PRINT key.

HELP-53 Widthwise (main-scanning direction) 2. Enter 4-digit value using the NUMERIC keys
master making start position for online master to change the setting.
making
AB C D Amount of change
1. Access HELP mode H-53 and press the 0111 -7.0mm
PRINT key. 0110 -6.0mm
0101 -5.0mm
2. Enter 4-digit value using the NUMERIC keys
0100 -4.0mm Forward
to change the setting.
0011 -3.0mm
0010 -2.0mm
AB C D Amount of change
0001 -1.0mm
0111 -7.0mm
0000 ±0.0mm
0110 -6.0mm Default
1000 ±0.0mm
0101 -5.0mm
1001 +1.0mm
0100 -4.0mm Backward
1010 +2.0mm
0011 -3.0mm (Default)
1011 +3.0mm
0010 -2.0mm
1100 +4.0mm Backward
0001 -1.0mm
1101 +5.0mm
0000 ±0.0mm
Default 1110 +6.0mm
1000 ±0.0mm 1111 +7.0mm
1001 +1.0mm
1010 +2.0mm
1011 +3.0mm
1100 +4.0mm Forward Forward
1101 +5.0mm
1110 +6.0mm
H-16
1111 +7.0mm Printing direction

Backward

H-53 Printing direction


3. Press the ×= key.
Backward Forward The setting will be memorized.
During memorization, “SAVE” will be
displayed.

3. Press the ×= key.


The setting will be memorized.
During memorization, “SAVE” will be
displayed.

6
U5-Y1050
2009.09

You might also like