Wiring a radionic device with a RF Broadband Amp

Running wires directly to amp

This design will work with or without amplification.

Illustration by Tim Pitts INPUT COIL Sample Well

Technical Assistance Mario Silvestri, Stella Estel, Ricardo Ribeiro, Juan Munoz

Information Input -
Information Input +
RCA
Potency Dial Dial 9 Dial 8 Dial 7 Dial 6 Dial 5 Dial 4 Dial 3 Dial 2 Dial 1 Aux In
(first dial)
Power 1 MEG 10K 10K 10K 10K 10K 10K 10K 10K 10K
LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR
Supply +
3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1
1K
Resistor 4.7K
On/Off 1uf
LED Resistor
Capasitor

Information Input +

STICK PAD KRT Perfect Spiral Power Pump

On/Off with tensor ring.
Switch Place flat below input well.
Power Supply Potency Dial
Ground - 1 Meg pot
Attach Ring Magnet
9-12V with south side to
Power bottom of pot
Plug Coils can be either Copper Conductive Adhesive Tape
Surface soldering is required. or Enameled Magnet Wire (with the very ends scraped
Tin the surface and wire tips first. free of coating)
Apply solder firmly and quickly.
Wrap around a Borosilicate or Pyrex beaker
RF (Radio Frequency) Amp
Wound Mobis Coil OUTPUT COIL Sample Well
Broadband 1-2000MHz KRT Perfect Spiral Power Pump
goes under acrylic plastic Diagnose
with tensor ring.
Place flat below output well.
Act as additional antenna

Diagnose
1K
Act as additional antenna Two Way
Resistor
Switch to choose
source of input
1K between before
Resistor amp and after amp.

RCA Out
to Antenna
or hand hold
 Wiring a radionic device with a low voltage LM386 amplifier
The LM386 is not considered to be as well suited as the RF amp.

Illustration by Tim Pitts INPUT COIL Sample Well

Technical Assistance Mario Silvestri, Stella Estel, Ricardo Ribeiro, Juan Munoz

Information Input -

RCA
Potency Dial Dial 9 Dial 8 Dial 7 Dial 6 Dial 5 Dial 4 Dial 3 Dial 2 Dial 1 Aux In
(first dial)
Volume
Knob Power 1 MEG 10K 10K 10K 10K 10K 10K 10K 10K 10K
Supply + LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR LINEAR
3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1 3 2 1

On/Off 4.7K
Resistor 1uf
LED Capasitor

Information Input +

STICK PAD KRT Perfect Spiral Power Pump

On/Off with tensor ring.
Switch Place flat below input well
Power Supply Potency Dial
Ground - 1 Meg pot
Attach Ring Magnet
9-12V with south side to
Power bottom of pot
Plug Coils can be either Copper Conductive Adhesive Tape
or Enameled Magnet Wire (with the very ends scraped
free of coating)

Wrap around a Borosilicate or Pyrex beaker

Wound Mobis Coil OUTPUT COIL Sample Well

LM386 Audio Amplifier KRT Perfect Spiral Power Pump
goes under acrylic plastic Diagnose
with tensor ring.
Place flat below output well.
Act as additional antenna

Diagnose
Two Way

Act as additional antenna

Switch to choose
source of input
1K between before
Resistor amp and after amp.

RCA Out
to Antenna
or hand hold