Scribd Logo
Upload

Welcome to Scribd!

  • 104 views

    Edoc 006467

    Uploaded by

    Fernando GC
    These fuse units are tested in accordance with procedures described in ANSI Standard C37.41-1981. The minimum melting current is not less than 200% of fuse-unit ampere rating. Fuse units having nickel-chrome or silver element construction are not subject to damage.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Edoc 006467

    Uploaded by

    Fernando GC
    104 views1 page
    These fuse units are tested in accordance with procedures described in ANSI Standard C37.41-1981. The minimum melting current is not less than 200% of fuse-unit ampere rating. Fuse units having nickel-chrome or silver element construction are not subject to damage.

    Original Title

    EDOC_006467

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    These fuse units are tested in accordance with procedures described in ANSI Standard C37.41-1981. The minimum melting current is not less than 200% of fuse-unit ampere rating. Fuse units having nickel-chrome or silver element construction are not subject to damage.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    104 views1 page

    Edoc 006467

    Uploaded by

    Fernando GC
    These fuse units are tested in accordance with procedures described in ANSI Standard C37.41-1981. The minimum melting current is not less than 200% of fuse-unit ampere rating. Fuse units having nickel-chrome or silver element construction are not subject to damage.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    CURRENT IN AMPERES

    1000 900 800 700 600 500 400 5 6 7 8 9 10 20 30 40 50 60 70 80 90 80000 90000 100000 1000 900 800 700 600 500 400 300 200 100 90 80 70 60 50 40 30 20 10 9 8 7 6 5 8000 9000 10000 20000 30000 40000 50000 60000 70000 800 900 1000 2000 3000 4000 5000 6000 7000 100 200 300 400 500 600 700

    100E

    125E

    13E 15E

    300

    200

    100 90 80 70 60 50 40

    30

    20

    10 9 8 7 6 5

    TIME IN SECONDS

    150E 175E 200E

    10E

    20E

    25E

    30E

    40E

    50E

    65E

    80E

    5E

    7E

    TIME IN SECONDS

    1 .9 .8 .7 .6 .5 .4

    1 .9 .8 .7 .6 .5 .4

    .3

    .3

    .2

    .2

    .1 .09 .08 .07 .06 .05 .04

    .1 .09 .08 .07 .06 .05 .04

    .03

    .03

    .02

    .02

    .01 100 200 300 400 500 600 700 800 900 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 20000 30000 40000 50000 60000 70000 80000 90000 100000 5 6 7 8 9 10 20 30 40 50 60 70 80 90

    .01

    CURRENT IN AMPERES

    TOTAL CLEARING TIME-CURRENT CHARACTERISTIC CURVES


    SMU FUSE UNITSS&C STANDARD SPEED
    BASISThese fuse units are tested in accordance with the procedures described in ANSI Standard C37.41-1981, and they are rated to comply with ANSI Standard C37.46-1981. As required by these standards, the minimum melting current is not less than 200% of fuse-unit ampere rating, and the minimum melting and total clearing curves are based on tests starting with the fuse unit at an ambient temperature of 25C and no initial load. CONSTRUCTIONFusible elements for fuse units rated 5E and 7E amperes are nickel-chrome, under controlled tension; fusible elements for fuse units rated 10E through 200E amperes are silver, helically coiled. All are of solderless construction. TOLERANCESCurves are plotted to maximum test points. All variations are minus. APPLICATIONLike all high-voltage fuses, these fuse units are intended to accommodate overloads, not to interrupt them. Accordingly, they feature fusible elements which are designed with a minimum melting current of 200% of the fuse-unit ampere rating (for fuse units rated 100 amperes or less) or 240% of the fuse-unit ampere rating (for fuse units rated over 100 amperes). As a result, these fuse units have considerable peak-load capabilities; however, they should never be exposed to loading in excess of the peak-load capabilities listed in S&C Data Bulletin 240-190.
    Since fuse units having nickel-chrome or silver element construction are not subject to damage by aging or transient overcurrents, it is unnecessary to replace unblown fuse units of either of these constructions in single-phase or three-phase installations when one or more fuse units have blown.

    COORDINATIONThese curves represent the total time required for a fuse unit to melt and interrupt a fault current, and should be followed in coordination problems where fuses are applied as protecting devices.
    Any preloading reduces melting time. With respect to the protected fuse, the effect of preloading must be determined and adjustments made to its minimum melting curve: 1. When close coordination is required; 2. When, regardless of the preciseness of coordination, the protected fuse is subjected to temporary overloads. There are cases where the coordination requirements may be very exacting, for example, in coordinating a transformer primary fuse with a secondary breaker and a source-side breaker. The time interval between the operating characteristics of the two breakers may be very narrow. Under these circumstances there must be an extremely short time interval between the minimum melting and the total clearing characteristics of the fuse. The fuse units represented by these curves possess this short time interval feature, sincehaving a nondamageable fusible element of precise constructionthey require: 1. As little as 10% total tolerance in melting currentcompared to the 20% tolerance of many fuses (20% and 40% respectively in terms of time). 2. No safety-zone or setback allowances. This narrow time band normally will provide the desired coordination. If the selected S&C Standard Speed fuse unit does not meet the coordination requirements, the selection of another ampere

    rating for either the protecting or protected fuse usually will satisfy. Do not assume that other fuses that do not employ S&Cs silver, helically coiled fusible element construction can better resolve a coordination impasse than the use of another ampere rating in one of the S&C speed options. Such other fuses, including time-lag speeds, super-slow speeds, and high-surge speeds, require the use of safety-zone or setback allowances and, in addition, they have larger construction tolerances (plus 20% in current; plus 40% in terms of time). The application of these two factors will give a time interval between the adjusted minimum melting curve and the total clearing curve greater than in the case of S&C speed options.

    FUSE UNITS AVAILABLE Type Kv Nom. Ratings Ampere Ratings SMU-20 . . . . . . . . . . . . . . . . . 14.4 . . . . . . . . . . .5E through 200E

    Supersedes TCC No. 153-1-2 dated 8-24-87

    c1988

    TCC NUMBER

    153-2-2
    Page 1 of 1 August 29, 1988

    S&C ELECTRIC COMPANY Chicago S&C ELECTRIC CANADA LTD. Toronto

    You might also like