Conductometric Titrations

Conductometry & Conductometric Titrations
1. Conductometry :-
Introduction
Ohm’s law.
Conductometric measurements.
Factor affecting conductivity.
Application of conductometry.
2.Conductometric Titration :-
Introduction.
Types of conductometric tiration.
Advantages of conductometric tiration.
3.Recent devlopement
4.References .
Total conductance of the solution is directly proportional to
the sum of the n individual ion contributions .
G = ∑ciΛm,i
Ohm’s law-
Conductivity measurements
1. Electrodes
Two parallel platinized Pt. foil electrodes or Pt. black with
electrodeposited a porous Pt. film which increases the surface
area of the electrodes and further reduces faradaic polarization.
2. Primary standard solutions

Primary standard KCl solution ,at 25°C , 7.419g of KCl in 1000g
of solution has a specific conductivity of 0.01286Ω -1/cm
3. Conductivity Cell :
Avoid the change of temperature during determination
4.Wheat stone bridge :

Factors affecting conductivity:
Size of ions
Temperature
Number of ions
Charge of ions
Specific conductivity:-It is conductivity offered by a

substance of 1cm length and 1sq.cm surface area. units
are mhos/cm.
Equivalent conductivity:-it is conductivity offered by a
solution containing equivalent weight of solute in it.
Molar conductance of various ions at infinite
dilution at 25℃
Ions Molar Conductance

K+ 73.52
Na+ 50.11
Li+ 38.69
H+ 349.82
Ag+ 61.92
Cl- 76.34
Br- 78.4
OH- 198
10
The determination of specific conductance of an electrolytic
solution, thus, consists of two steps:
•Determination of cell constant by using a standard KCl
solution of known concentration in the conductivity cell.
•Determination of resistance of he given solution using the
same cell. The reciprocal of this gives the value of
conductance. Multiplication of conductance and cell constant
gives the value of specific conductance of the solution.
In conductance measurements, the solutions are always

prepared in conductivity water which has no conductance due
to dissolved impurities.
It is prepared by distilling a number of times the distilled water
to which a little KMnO4 and KOH have been added in a hard
glass distillation assembly.
Such water has very low conductance of the order of 4.3 × 10-
8
ohm-1. For ordinary purposes, double distilled water may be
used.
APPLICATIONS OF CONDUCTOMETRY
It can be used for the determination of:-

Solubility of sparingly soluble salts
Ionic product of water
Basicity of organic acids
Salinity of sea water (oceanographic work)
Chemical equilibrium in ionic reactions
Conductometric titration
CONDUCTOMETRIC TITRATIONS:
The determination of end point of a titration by

means of conductivity measurements are known as
conductometric titrations.
Types of conductometric titrations:
 Acid-base titration
 Precipitation titration
 Replacement titration
 Redox (oxidation-reduction) titration
 Complexometric titration
Strong Acid with a Strong Base.
e.g. HCl with NaOH:
Before NaOH is added, the conductance is high due to the presence of highly mobile
hydrogen ions.
When the base is added, the conductance falls due to the replacement of hydrogen
ions by the added cations as H+ ions react with OH− ions to form undissociated water.
This decrease in the conductance continues till the equivalence point. At the
equivalence point, the solution contains only NaCl.
After the equivalence point, the conductance increases due to the large
conductivity of OH- ions
Weak Acid with a Strong Base,
e.g. acetic acid with NaOH:
Initially the conductance is low due to the feeble

ionization of acetic acid. On the addition of
base, there is decrease in conductance not only
due to the replacement of H+ by Na+ but also
suppresses the dissociation of acetic acid due
to common ion acetate.
But very soon, the conductance increases on

adding NaOH as NaOH neutralizes the un-
dissociated CH3COOH to CH3COONa which is
the strong electrolyte.
This increase in conductance continues raise
up to the equivalence point. The graph near the
equivalence point is curved due the hydrolysis
of salt CH3COONa.
Beyond the equivalence point, conductance

increases more rapidly with the addition of
NaOH due to the highly conducting OH− ions
Weak Acid with a Weak Base:
The nature of curve before the equivalence point is
similar to the curve obtained by titrating weak acid
against strong base.
After the equivalence point, conductance virtually

remains same as the weak base which is being
added is feebly ionized and, therefore, is not much
conducting
Mixture of a Strong Acid and a Weak Acid vs. a Strong
Base or a Weak Base:
In this curve there are two break points. The first break point corresponds
to the neutralization of strong acid.
When the strong acid has been completely neutralized only then the weak
acid starts neutralizing.
The second break point corresponds to the neutralization of weak acid and
after that the conductance increases due to the excess of OH− ions in case
of a strong base as the titrant.
However, when the titrant is a weak base, it remains almost constant after
the end point similar to previous titration
PRECIPITATION TITRATIONS:-
[K++Cl-]+[Ag++No3_]
A reaction may be made the basis of a conductometric
precipitation titration provided the reaction product is sparingly
soluble or is a stable complex. The solubility of the precipitate
(or the dissociation of the complex) should be less than 5%.
The addition of ethanol is sometimes recommended to reduce
the solubility in the precipitations.
REPLACEMENT
TITRATIONS
Salt of strong acid and
weak base vs. strong base
Ex: ammonium chloride vs.
sodium hydroxide
Salt of strong base and

weak acid vs. strong acid
Eg: sodium acetate vs.
hydrochloric acid
COMPLEXOMETRIC TITRATION
Ex.:-KCl vs. Hg(ClO4)2
Non-aqueous titrations can also be measured

using conductometry.
Ex:-
a)titration of weak bases vs. perchloric acid in
dioxan-formic acid.
b)Titration of weak organic acids in methanol vs.
tetra methyl ammonium hydroxide in methanol-
benzene.
ADVANTAGES OF
CONDUCTOMETRIC TITRATIONS
No need of indicator
Colored or dilute solutions or turbid suspensions can
be used for titrations.
Temperature is maintained constant throughout the
titration.
End point can be determined accurately and errors
are minimized as the end point is being determined
graphically.
RECENT DEVELOPEMENTS
In refinary industries.

Estimation of polyelectrolytic solution.
Biotechnology.
Microbiosensors for enviromental monitoring .
THANK YOU

Conductometric Titrations

Uploaded by

Copyright:

Available Formats

Conductometric Titrations

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Conductometric Titrations

Uploaded by

Copyright:

Available Formats

Conductometry & Conductometric Titrations

2. Primary standard solutions

Avoid the change of temperature during determination

4.Wheat stone bridge :

Specific conductivity:-It is conductivity offered by a

Ions Molar Conductance

In conductance measurements, the solutions are always

It can be used for the determination of:-

The determination of end point of a titration by

Initially the conductance is low due to the feeble

But very soon, the conductance increases on

Beyond the equivalence point, conductance

After the equivalence point, conductance virtually

Salt of strong base and

Non-aqueous titrations can also be measured

In refinary industries.

You might also like