H0T(C) Series Bullet Camera

User Manual

User Manual
Thank you for purchasing our product. If there are any
questions or requests, do not hesitate to contact the
dealer.
This manual applies to models below:

Model
DS-2CE17H0T-IT1/3/5F(C)

This manual may contain several technical mistakes or

printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.

0100002001207
Regulatory Information
FCC Information
Please take attention that changes or modification not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.

EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
standards listed under the Low Voltage Directive
2014/35/EU, the EMC Directive 2014/30/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a
battery that cannot be disposed of as
unsorted municipal waste in the European
Union. See the product documentation for
specific battery information. The battery is
marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For
more information, see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.

Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Safety Instruction

Warnings
 In the use of the device, you must be in strict
compliance with the electrical safety regulations of
the nation and region.
 Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12
VDC according to the IEC60950-1 standard and
IEC62368-1 standard. Refer to technical specifications
for detailed information.
 Do not connect multiple devices to one power
adapter to avoid over-heating or a fire hazard caused
by overload.
 The socket-outlet shall be installed near the
equipment and shall be easily accessible.
 Make sure that the plug is firmly connected to the
power socket.
 A readily accessible disconnect device shall be
incorporated external to the equipment.
 An overcurrent protective device shall be
incorporated external to the equipment, not
exceeding the specification of the building.
 An all-pole mains switch shall be incorporated in the
electrical installation of the building.
 If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cord, and
then contact the service center.
 Never attempt to disassemble the camera by
unprofessional personal.

Cautions
 No naked flame sources, such as lighted candles,
should be placed on the equipment.
 Install the equipment according to the instructions in
this manual.
 To prevent injury, this equipment must be securely
attached to the floor/wall in accordance with the
installation instructions.
 Do not touch the sharp edges or corners.
 Do not drop the camera or subject it to physical
shock.
 Do not touch senor modules with fingers.
 Do not place the camera in extremely hot, cold (the
operating temperature shall be -40°C to 60°C), dusty
or damp locations, and do not expose it to high
electromagnetic radiation.
 If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
 Do not aim the camera at the sun or extra bright
places.
 The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
 Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty or damp
environment.
 To avoid heat accumulation, good ventilation is
required for the operating environment.
 Keep the camera away from liquid while in use for
non-water-proof device.
 While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
1 Introduction
1.1 Product Features
The main features are as follows:
 High performance CMOS sensor
 OSD menu with configurable parameters
 Smart IR
 3-Axis Adjustment

1.2 Overview

Switch Button
Power Cord
Bracket Video Cable
Main Body
Lens

Figure 1-1 Overview of the Camera

Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.

2 Installation
Before you start:
 Make sure that the device in the package is in good
condition and all the assembly parts are included.
 Make sure that all the related equipment is power-off
during the installation.
 Check the specification of the products for the
installation environment.
 Check whether the power supply is matched with
your power output to avoid the damage.
 Make sure the wall is strong enough to withstand
three times the weight of the camera and the mount.
 If the product does not function properly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.

2.1 Ceiling/Wall Mounting without Junction Box

Before you start:
Ceiling mounting and wall mounting are similar.
Following steps take ceiling mounting as an example.
Steps:
1. (Optional) For cement ceiling, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.
2. (Optional) Drill the cable hole, when the cables are
routed through the ceiling.
3. Align the screw holes in the bracket to the ceiling,
and secure the camera with three PA4 × 25 screws
(supplied).

Figure 2-1 Secure the Camera on the Ceiling

4. Connect the power cord and video cable.
5. Power on the camera to check if the image on the
monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below.

Pan Position
[0° to 360°]
Trim Ring
Rotation Position
[0° to 360°] Tilt Position
[0° to 180°]
Screw A
Screw B

Figure 2-2 3-Axis Adjustment

1). Loosen the trim ring to adjust the pan position
[0° to 360°].
2). Loosen screw A to adjust the tilt position [0° to
180°].
3). Loosen screw B to adjust the rotation position [0°
to 360°].
6. Turn the trim ring clockwise and tighten the screws
A and B to finish installation.

2.2 Ceiling/Wall Mounting with Junction Box

Before you start:
 You need to purchase a junction box in advance.
 Ceiling mounting and wall mounting are similar.
Following steps take wall mounting as an example.
Steps:
1. Paste the drill template for junction box to the place
where you want to install the camera.
2. (Optional) For cement wall, drill the screw holes
with a 5.5 mm drill and insert the supplied wall
plugs.

Figure 2-3 Drill Template for Junction Box

3. (Optional) Drill the cable hole, when the cables are
routed through the wall.
4. Take apart the junction box.
5. Align the screw holes of the camera with those on
the junction box cover. Attach the camera to the
junction box cover with three PM4 × 10 screws.

Figure 2-4 Attach the Camera to the Junction Box Cover

6. Secure the junction box body on the wall with three
PA4 × 25 screws (supplied).
 Figure 2-5 Secure the Junction Box on the Wall
7. Route the cables through the bottom cable hole or
side cable hole of the junction box and connect the
cables.
8. Fix the junction box cover on its body with three
PM3 × 16 L6 screws that come with the junction
box.

Figure 2-6 Fix the Junction Box Cover on Its

Body
9. Repeat steps 5 to 6 of 2.1 Ceiling/Wall Mounting
without Junction Box to finish the installation.

3 Menu Description
Please follow the steps below to call the menu.
Note:
The actual display may vary with your camera model.
Steps:
1. Connect the camera with the TVI DVR, and the
monitor, as shown in figure 3-1.
TVI DVR
Camera Monitor

Figure 3-1 Connection

2. Power on the analog camera, TVI DVR, and the
monitor to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking button or
calling preset No. 95.
 VIDEO
FORMAT

EXPOSURE MODE

SHUTTER
AGC
EXPOSURE BACK
EXIT
SAVE & EXIT

MODE
DAY/NIGHT BACK
EXIT
SAVE & EXIT

IMAGE MODE
WHITE BALANCE
MAIN MENU BRIGHTNESS
CONTRAST

VIDEO SHARPNESS
SETTINGS SATURATION
DNR
MIRROR
BACK
EXIT
SAVE & EXIT

FACTORY
DEFAULT

EXIT

SAVE & EXIT

Figure 3-2 Main Menu Overview

5. Click the direction arrow to control the camera.
1). Click up/down direction button to select the
item.
2). Click Iris + to confirm the selection.
3). Click left/right direction button to adjust the
value of the selected item.

3.1 VIDOE FORMAT

You can set the video format to 5MP@20fps,
4MP@30fps, 4MP@25fps, 2MP@30fps, or
2MP@25fps.

3.2 EXPOSURE
Exposure describes the brightness-related parameters,
which can be adjusted by EXPOSURE MODE, SHUTTER
and AGC.
 EXPOSURE

EXPOSURE MODE GLOBAL

SHUTTER AUTO
AGC LOW
BACK 
EXIT 
SAVE & EXIT 

Figure 3-3 EXPOSURE

EXPOSURE MODE
You can set the EXPOSURE MODE to GLOBAL, BLC, HLC,
or DWDR.
 GLOBAL
GLOBAL refers to the normal exposure mode which
performs exposure according to the whole image
brightness.
 BLC (Backlight Compensation)
BLC (Backlight Compensation) compensates light for the
front object to make it clear, but this may cause the
over-exposure of the background, where the light is
strong.
 HLC (Highlight Compensation)
HLC stands for highlight compensation. The camera
detects the strong spots (the over-exposure portion of
image), then reduce the brightness of the strong spots
to improve the overall images.
 DWDR (Digital Wide Dynamic Range)
The DWDR helps the camera provide clear images even
under backlight circumstances. When both very bright
and very dark areas simultaneously exist in the image,
DWDR balances the brightness level of the whole image
to provide clear images with details.
SHUTTER
SHUTTER is a photographic device that administers the
exposure by limiting the time over which light is
admitted.
AGC (Automatic Gain Control)
It optimizes the clarity of the image in poor light
conditions. The AGC level can be set to HIGH, MEDIUM,
or LOW.
Note:
The noise will be amplified, when setting the AGC level.

3.3 DAY/NIGHT
COLOR, BW (Black and White), and AUTO are selectable
for DAY/NIGHT switch.
COLOR
The image is colorful in day mode all the time.
B&W (Black and White)
The image is black and white all the time, and the IR
LIGHT turns on in the poor light conditions.
You can turn on/off the IR LIGHT and set the value of
SMART IR in this menu
 DAY/NIGHT
B&W
MODE
ON
IR LIGHT
SMART IR 2
BACK 
EXIT 
SAVE & EXIT 

Figure 3-4 B&W

 IR LIGHT
You can turn on/off the IR LIGHT to meet the
requirements of different circumstances.
 SMART IR
The Smart IR function is used to adjust the light to its
most suitable intensity, and prevent the image from
over exposure. The SMART IR value can be adjusted
from 1 to 3. The higher the value, the more obvious
effects.
AUTO
Automatically switch Color, or B&W (Black and White)
according to actual scene brightness.
You can turn on/off the IR LIGHT, and set the value of
SMART IR in this menu.

DAY/NIGHT

MODE AUTO
IR LIGHT ON
SMART IR 2
D  N THRESHOLD 5
N  D THRESHOLD 5
BACK 
EXIT 
SAVE & EXIT 

Figure 3-5 AUTO

 IR LIGHT
You can turn on/off the IR LIGHT to meet the
requirements of different circumstances.
 SMART IR
The Smart IR function is used to adjust the light to its
most suitable intensity, and prevent the image from
over exposure. The SMART IR value can be adjusted
from 1 to 3. The higher the value, the more obvious
effects.
 D N Threshold (Day to Night Threshold)
Day to Night Threshold is used to control the sensitivity
of switching the day mode to the night mode. You can
set the value from 1 to 9. The larger the value, the more
sensitive the camera.
 N D Threshold (Night to Day Threshold)
Night to Day Threshold is used to control the sensitivity
of switching the night mode to the day mode. You can
set the value from 1 to 9. The larger the value, the more
sensitive the camera.
3.4 VIDEO SETTINGS
Move the cursor to VIDEO SETTINGS and click Iris+ to
enter the submenu. IMAGE MODE, WHITE BALANCE,
BRIGHTNESS, CONTRAST, SHARPNESS, SARUTATION,
DNR, and MIRROR are adjustable.

VIDEO SETTINGS

IMAGE MODE STD

WHITE BALANCE 
BRIGHTNESS 5
CONTRAST 5
SHARPNESS 5
SATURATION 5
DNR 5
MIRROR OFF
BACK 
EXIT 
SAVE & EXIT 

Figure 3-6 VIDEO SETTINGS

IMAGE MODE
IMAGE MODE is used to adjust the image saturation.
You can set it to STD (Standard), or HIGH-SAT (High
Saturation).
WHITE BALANCE
White balance, the white rendition function of the
camera, is to adjust the color temperature according to
the environment. It can remove unrealistic color casts in
the image. You can set the mode to AUTO or MANUAL.
 AUTO
Under AUTO mode, white balance is being adjusted
automatically according to the color temperature of the
scene illumination.
 MANUAL
You can adjust the R-GAIN and B-GAIN value to correct
colors manually.

WHITE BALANCE

MODE MANUAL
R-GAIN 5
B-GAIN 5
BACK 
EXIT 
SAVE & EXIT 

Figure 3-7 MANUAL MODE

BRIGHTNESS
Brightness refers to the brightness of the image.
You can set the brightness value to darken or brighten
the image. The higher the value is, the brighter the
image is.
CONTRAST
This feature enhances the difference in color and light
between parts of an image.
SHARPNESS
Sharpness determines the amount of detail an imaging
system can reproduce.
SATURATION
Saturation is the proportion of pure chromatic color in
the total color sensation. The saturation of a color is
determined by a combination of light intensity and how
much it is distributed across the spectrum of different
wavelengths.
DNR (Digital Noise Reduction)
The DNR function can decrease the noise effect,
especially when capturing moving images in poor light
conditions and delivering more accurate and sharp
image.
MIRROR
OFF, H, V, and HV are selectable for mirror.
OFF: The mirror function is disabled.
H: The image flips 180° horizontally.
V: The image flips 180° vertically.
HV: The image flips 180° both horizontally and
vertically.

3.5 FACTORY DEFAULT

Move the cursor to FACTORY DEFAULT and click Iris+ to
reset all the settings to the factory default.

3.6 EXIT
Move the cursor to EXIT and click Iris+ to exit the menu
without saving.

3.7 SAVE & EXIT

Move the cursor to SAVE & EXIT and click Iris+ to save
the settings and exit the menu.

UD18172B-B