ASSESSMENT G8 TLE q2

PAMBISAN NATIONAL HIGH SCHOOL
Assessment
Grade 8 TLE
Quarter 2
Direction: Choose the letter of the correct answer and write your answer in your answer sheet.
1. Which tool has a cross tip resembling a positive (+) sign and it is used to drive screws with cross slot heads?
a. Stubby Screwdriver c. Connectors
b. Philips Screwdriver d. Wire Stripper
2. Which tool is used for cutting and holding wires and can reach tight space or small opening, and is used in
making terminal loops of copper wires?
a. Long Nose Plier c. Combination Plier
b. Electricians Knife d. Wire Stripper
3. Which tool is used for gripping, holding, cutting electrical wires and even small nails, and is usually used by
linemen in doing heavy tasks?
4. Which tools is used in driving or pounding and pulling out nails?
a. Hammer c. Connectors
b. Portable Electric Drill d. Wire Stripper
5. Which is a small drilling machine with a chuck capacity of ¼ “to 3/8 “and used for making and for marking holes
on metal sheets and concrete walls.
a. Hammer c. Connectors
b. Portable Electric Drill d. Wire Stripper
6. Which of these comes in either Standard or Philips screwdriver with short shank or blade and short handle used
to turn screws in tight spaces where standard screwdriver cannot be used?
a. Stubby screwdriver c. Connectors
b. Philips screwdriver d. wire stripper
7. Which tool is used for removing insulation of medium - sized wires ranging from gauge #10 to gauge #16?
8. Which is used by linemen to remove insulation of wire and cables in low and high voltage transmission lines?
a. Long Nose Pliers c. Combination Pliers
9. Which is a circuit protective device that automatically blows and cuts the current when an overload or short
circuit happens?
a. Circuit Breaker c. Junction box
b. Fuse d. Conduits
10. Which is a rectangular–shaped metallic or plastic (PVC) material in which flush– type convenience outlet and
switch are attached?
a. junction box c. Conduits
b. Connectors d. Utility Box
11. Which electrical materials are used as the passage of wires for protection and insulation?
a. Junction Box c. Conduits
b. Connectors d. Male Plug
12. Which protective device is used to automatically cut off the current when there is trouble in the circuit such as
short circuit or overload occurs?
a. Circuit Breaker c. Conduits
b. Fuse d. Junction Box
13. Which is an octagonal–shaped electrical material where the connections or joints of wires are being done?
b. Utility Box d. Connectors
14. Which are used to attach metallic or non–metallic conduit to the junction or utility boxes?
a. Male Plug c. Junction Box
b. Conduits d. Connectors
15. Which device is inserted to a convenience outlet to conduct electric current and flat cord is attached to it on one
end and the other end is connected to a current- consuming instrument or appliance?
b. Connectors d. Male Plug
16. Which tool is a flexible tape that slides into a material case and is used to measure irregular
and regular shapes?
a. Push pull Tape b. pliers c. caliper rule d. hammers
17. Which tool is used to elevate heavy objects with its lifting saddle?
a. marking gauge b. air chisel c. Hydraulic floor jack d. pullers
18. Which tool is used to remove gears, hubs, and cylinders?
a. electric drill b. Puller c. portable crane d. screwdriver
19. Which among the tools uses air motor to turn the socket drive?
a. air chisel b. marking gauge c. hammer d. Air racket
20. Which tool is used in making holes on metal sheets and concrete walls?
a. Electric drill b. air chisel c. grinding wheel d. push pull rule
21. Which tool is used to apply force on bent parts to straighten them?
a. air impact wrench b. plier c. air drill d. Hydraulic press
22. Which is the most appropriate tool used in making lines parallel with the edges of the wood?
a. puller b. zigzag rule c. wrench d. Marking Gauge
23. Which tool is used to drive and pull out nails?
a. Hammer b. screwdriver c. electric drill d. puller
24. Which tool uses compressed air turn nuts, bolts, and other objects?
a. air chisel b. Air impact wrenches c. puller d. electric drill
25. Which tool is used to loosen or tighten screws with slotted heads?
a. plier b. Hammer c. Screwdriver d. air racket
26. Which tool is used for cleaning the floor and car interiors?
a. grinding wheel b. Vacuum cleaner c. Screwdriver d. hammer
27. Which tool is used for lifting the engine out of the car?
a. electric drill b. Puller c. portable crane d. screwdriver
28. Which tool uses compressed air to provide speed and constant power in a range of drilling
tasks?
a. Air drill b. Hammer c. Screwdriver d. air racket
29. Which tool is used to turn screws, nuts and bolts with hexagonal heads?
a. puller b. zigzag rule c. wrench d. Marking Gauge
30. Which tool is used for various grinding and abrasive machining operations?
a. grinding wheel b. Vacuum cleaner c. Screwdriver d. hammer
GOD BLESS….always keep safe….

ASSESSMENT G8 TLE q2

Uploaded by

Copyright:

Available Formats

ASSESSMENT G8 TLE q2

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ASSESSMENT G8 TLE q2

Uploaded by

Copyright:

Available Formats

PAMBISAN NATIONAL HIGH SCHOOL

GOD BLESS….always keep safe….

You might also like