HEAT TRANSFER

Kotiba Hamad - Sungkyunkwan university

Problems
Problem 1
If inner and outer faces of a concrete wall with thickness of 20 cm is kept at a
temperature 20 °C and -5 C, respectively, and the thermal conductivity of the concrete
is 1.2 W/m.K. Determine the heat loss through a wall 10 m long and 3 m high.
Problems
Problem 1
 10 m long, 3 m high, and 0.2 m thick concrete wall.
 Thermal conductivity of the concrete (k) = 1.2 W/m.K
 Temperature of the inner surface (Ti) = 20 °C
 Temperature of the outer surface (To) = –5 °C
 One dimensional heat flow
 The system has reached steady state.
Problems
Problem 1
Problems
Problem 2
A wall with 7.5 cm thickness (shown below) generates heat at the rate of 105 W/m3.
One side of the wall is insulated, and the other side is exposed to an environment at
90°C. The convective heat transfer coefficient between the wall and the environment is
500 W/m2.K. Under one-dimensional-steady state conditions, and if the thermal
conductivity of the wall is 12 W/m.K, calculate the maximum temperature in the wall.
Problems
Problem 2
 Plane wall with internal heat generation
 Thickness (L) = 0.075 m
 Internal heat generation rate (qG ) = 105 W/m3
 One side is insulated
 Ambient temperature on the other side (T) = 90 °C
 Convective heat transfer coefficient ( hc ) = 500 W/(m2 K)
 Thermal conductivity (k) = 12 W/m.K.
 The heat loss through the insulation is negligible.
 The system has reached steady state.
 One dimensional conduction through the wall.
Problems
Problem 2
The one dimensional conduction equation:

To solve this equation, two boundary conditions are needed:

1. No energy loss through the insulator.
2. Convection at the other surface
Problems
Problem 2
1. No energy loss through the insulator.

2. Convection at the other surface

Problems
Problem 2
1. No energy loss through the insulator.
Problems
Problem 2
2. Convection at the other surface
Problems
Problem 2
Substituting this into the expression for T yields the temperature distribution in the
wall:

The maximum temperature occurs at x = 0.

Problems
Problem 3
A composite wall (shown below) has uniform temperatures. If the thermal
conductivities of the wall materials are: kA = 70 W/m.K, kB = 60 W/m.K, kC = 40 W/m.
K, and kD = 20 W/m.K, determine the rate of heat transfer through this section of the
wall and the temperatures at the interfaces. (Surfaces normal to heat transfer direction
are isothermal).
Problems
Problem 3
 A section of a composite wall
 Thermal conductivities
 kA = 70 W/m.K
 kB = 60 W/m.K
 kC = 40 W/m.K
 kD = 20 W/m.K
 Surface temperatures
 Left side (TAs) = 200 °C
 Right side (TDs) = 50 °C
 One dimensional conduction
 The system is in steady state
 The contact resistances between the materials is negligible
Problems
Problem 3
Problems
Problem 3
The total thermal resistance is
Problems
Problem 3
The average temperature at the interface between material A and materials B and C
(TABC) can be determined by considering the conduction through material A alone.
Problems
Problem 3
The average temperature at the interface between material D and materials B and C
(TBCD) can be determined by considering the conduction through material D alone
Problems
Problem 4
A composite wall (shown below) has uniform temperatures. If the thermal
conductivities of the wall materials are: kA = 70 W/m.K, kB = 60 W/m.K, kC = 40 W/m.
K, and kD = 20 W/m.K, and contact resistance at each interface Ri = 0.1 K/W,
determine the rate of heat transfer through this section of the wall and the temperatures
at the interfaces. (Surfaces normal to heat transfer direction are isothermal).
Problems
Problem 4
 A section of a composite wall
 Thermal conductivities
 kA = 70 W/m.K
 kB = 60 W/m.K
 kC = 40 W/m.K
 kD = 20 W/m.K
 Surface temperatures
 Left side (TAs) = 200 °C
 Right side (TDs) = 50 °C
 One dimensional conduction
 The system is in steady state
 Contact resistance at each interface (Ri) = 0.1 K/W
Problems
Problem 4
Problems
Problem 4

The total rate of heat transfer through the composite wall is given by:
Problems
Problem 4
(b) The average temperature on the A side of the interface between material A and
material B and C (T1A) can be determined by considering the conduction through
material A alone.

The average temperature on the B and C side of the interface between material A
and materials B and C (T1BC) can be determined by considering the heat transfer
through the contact resistance.
Problems
Problem 4
The average temperature on the D side of the interface between material D and
materials B and C (T2D) can be determined by considering the conduction through
material D alone.

The average temperature on the B and C side of the interface between material D and
materials B and C (T2BC) can be determined by considering the heat transfer through the
contact resistance.