FAR2 XX 7 Ime

Comply with MSC.
192(79)
MARINE RADAR/ARPA
FAR-2117/2127/2817/2827
FAR-2117-BB/2127-BB
Installation Manual
TABLE OF CONTENTS 3.7 Dual Radar Display
(non IMO-type only) ..................3-16
SAFETY IINSTRUCTIONS ..................... i
4. INSTALLING OPTIONAL
EQUIPMENT LISTS...............................iii
EQUIPMENT................................ 4-1
SYSTEM CONFIGURATION .................vi 4.1 Gyro Converter GC-10 .................4-1
4.2 Memory Card Interface Unit..............4-9
1. MOUNTING..................................... 1-1
4.3 DVI-RGB Conversion Kit
1.1 Antenna Unit.................................1-1
(for VDR connection) ..................4-12
1.2 Monitor Unit..................................1-6
4.4 Performance Monitor PM-31 ......4-15
1.3 Control Unit ................................1-10
4.5 BNC Connector Converter .........4-17
1.4 Processor Unit............................1-15
4.6 Junction Box...............................4-18
2. WIRING ........................................ 2-1
2.1 Interconnection.............................2-1 5. INPUT/OUTPUT DATA ................ 5-1
2.2 Antenna Unit.................................2-2
INSTALLATION MATERIALS,
2.3 Monitor Unit..................................2-6
ACCESSORIES,SPARE PARTS ........ A-1
2.4 Processor Unit..............................2-7
2.5 Changing AC Power Specification of
OUTLINE DRAWINGS ...................... D-1
Processor Unit ..........................2-12 INTERCONNECTION DIAGRAMS ... S-1
3. SETTING AND ADJUSTMENT .... 3-1

3.1 DIP Switch Setting .......................3-1
3.2 Initializing Tuning..........................3-2
3.3 Heading Alignment .......................3-3
3.4 Adjustment Sweep Timing............3-6
3.5 Suppressing Main Bang ...................3-7
3.6 Other Settings ..............................3-8
www.furuno.co.jp
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone : +81-(0)798-65-2111
Fax : +81-(0)798-65-4200
All rights reserved. Printed in Japan A : JAN . 2004

M : APR . 08, 2011
Pub. No. IME-35190-M
(HIMA ) FAR-2117/27/2817/27 *00017532310*
*00017532310*
* 0 0 0 1 7 5 3 2 3 1 0 *
SAFETY INSTRUCTIONS
The operator and installer must read the applicable safety instructions before attempting to
install or operate the equipment.
Indicates a potentially hazardous situation which, if not avoided,

DANGER will result in death or serious injury.

WARNING could result in death or serious injury.

CAUTION can result in minor or moderate injury.
Warning, Caution Prohibitive Action Mandatory Action
DANGER
Wear a safety belt and hard hat when working on the antenna unit.
Serious injury or death can result if someone falls from the radar antenna
mast.
WARNING
Radio Frequency Radiation Hazard
The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful,
particularly to your eyes. Never look directly into the antenna aperture from a close distance
while the radar ius in operation or eexpose yourself to the transmitting antenna at a close
distance. Distances at which RF radiation level of 100, 50 and 10 W/m 2 are given in the table
below.
Note: If the antenna unit is installed at a close distance in front of the wheel house, your
administration may require halt of transmission within a certain sector of antenna revolution.
This is possible. Ask your FURUNO representive or dealer to provide this feature.
2 2 2
Model Transceiver Magnetron Antenna * 100W/m 50W/m 10W/m
RTR-078A XN-12AF 0.3 m 1.2m 3.7 m
FAR-2817/2117 MAF1565N XN-20AF 0.1 m 0.7 m 2.2 m
(X-12 kw)
XN-24AF 0.1 m 0.4 m 1.5 m
RTR-079A XN-12AF 0.9 m 2.6 m 9.0 m
FAR-2827/2127 MG5436 XN-20AF 0.5 m 1.7 m 4.6 m
(X-25 kw)
XN-24AF 0.2 m 1.0 m 3.3 m
* : XN12AF: 4 ft, XN20AF: 6.5 ft, XN24AF: 8 ft
i
WARNING CAUTION
Do not open the equipment Observe the following compass safe
unless totally familiar with distances to prevent deviation of a
electrical circuits and magnetic compass:
service manual.
Standard Steering
compass compass
ELECTRICAL Only qualified personnel
should work inside the Antenna Unit
SHOCK (12 kw) 2.15 m 1.40 m
HAZARD equipment.
Antenna Unit
(25 kw) 2.05 m 1.30 m
Construct a suitable service platform Monitor Unit

(MU-201CR) 1.55 m 1.00 m
from which to install the antenna unit.
Monitor Unit
(MU-231CR) 1.85 m 1.20 m
Serious injury or death can result if some- Processor
one falls from the radar antenna mast. Unit (RPU-013) 1.35 m 0.85 m
Control Unit
0.30 m 0.30 m
Turn off the power at the mains switch- (RCU-014)
board before beginning the installation. Control Unit
0.95 m 0.60 m
(RCU-015)
Fire, electrical shock or serious injury can Control Unit
(RCU-016) 0.65 m 0.45 m
result if the power is left on or is applied
Memory Card
while the equipment is being installed. Interface Unit 0.90 m 0.60 m
(CU-200)
Be sure that the power supply is Junction Box
1.10 m 0.70 m
compatible with the voltage rating of (RJB-001)
the equipment. Switching Hub
1.00 m 0.60 m
Connection of an incorrect power supply (HUB-100)
can cause fire or damage the equipment . Monitor Unit
(MU-190) 1.65 m 1.05 m
Use only the specified power cable. Monitor Unit
0.85 m 0.55 m
Fire or damage to the equipment can result (MU-231)
if a different cable is used.
Do not install the monitor unit,
processor unit or control unit where
they may get wet from rain or
water splash.
Water in the units can result in fire,
electrical shock, or damage the equipment.
Attach securely protective

earth to the ship's body.
The protective earth
(grounding) is required to the
AC power supply to prevent
electrical shock.
ii
EQUIPMENT LISTS
Standard Supply
Name Type Code No. Qty Remarks
FAR-2117/2117-BB/2817, 24 rpm,
XN12AF-RSB096-078A -
1200 mm, W/CP03-24201
FAR-2117/2117-BB/2817, 42 rpm,
1200 mm, W/CP03-24201
FAR-2117/2117-BB/2817, 24 rpm,
2000 mm, W/CP03-19101
FAR-2117/2117-BB/2817, 42 rpm,
2000 mm, W/CP03-19101
FAR-2117/2117-BB/2817, 24 rpm,
2400 mm, W/CP03-19101
FAR-2117/2117-BB/2817, 42 rpm,
2400 mm, W/CP03-19101
Antenna Unit 1
FAR-2127/2127-BB/2827, 24 rpm,
1200 mm, W/CP03-24201
FAR-2127/2127-BB/2827, 42 rpm,
1200 mm, W/CP03-24201
FAR-2127/2127-BB/2827, 24 rpm,
2000 mm, W/CP03-19101
FAR-2127/2127-BB/2827, 42 rpm,
2000 mm, W/CP03-19101
FAR-2127/2127-BB/2827, 24 rpm,
2400 mm, W/CP03-19101
FAR-2127/2127-BB/2827, 42 rpm,
2400 mm, W/CP03-19101
MU-201CR For FAR-2117/2127
MU-231CR For FAR-2817/2827
Monitor Unit - 1
MU-190 For FAR-2117/2127
MU-231 For FAR-2817/2827
Processor Unit RPU-013 - 1
RCU-014 Standard type
Control Unit - 1
RCU-015 Trackball type
CP03-25601 008-535-550 1 For antenna unit
CP03-25700 000-080-435 15 m signal cable RW-9600
1
Installation Materials
CP03-25800 000-080-434 1 Cable assy. for monitor unit
CP03-25602 008-535-940 For RPU-013, AC set
1
CP03-25603 008-535-950 For RPU-013, DC set
FP03-09810 008-536-010 1 For monitor unit
Accessories FP03-09850 008-535-610 For RCU-014
1
FP03-09860 008-535-690 For RCU-015/016
iii
SP03-12501 008-485-360 1 For antenna unit
SP03-14404 008-535-910 For processor unit 100 VAC set
SP03-14405 008-535-920 1 For processor unit 220 VAC set
SP03-14406 008-535-930 For processor unit 24 VDC set
Spare Parts SP03-14401 008-535-990 For monitor unit AC set
For monitor unit, DC set,
SP03-03900 000-081-063
1 MU-201CR
For monitor unit, DC set,
SP03-14402 008-536-000
MU-231CR
Optional Equipment
Name Type Code No. Remarks
Gyro Converter GC-10-2 000-080-440 See chapter 4.
Performance Monitor PM-31 000-080-438 Mandatory for IMO radar
Converts 440 VAC to 100 VAC,
RU-1803 -
for processor unit
Transformer Unit
Converts 110/115/220/230 VAC
RU-3305 -
to 100 VAC, for de-icer
115/230 VAC to 24 VDC, for
RU-3424 -
processor unit (25 kW)
115/230 VAC to 24 VDC, for
Rectifier RU-1746B-2 -
processor unit (12 kW)
100/110/115/220/230 VAC to 24
RU-3423 -
VDC, for monitor unit
Memory Card Interface Unit CU-200-FAR 000-081-568 W/CP03-27430, See chapter 4.
External Buzzer OP03-21 000-030-097
Control Unit RCU-016 - Remote type, W/FP03-09860
RAM Card 00RAM08MC-005 004-376-740 8 MB
OP03-180-1 008-545-590 Mounted at factory
OP03-180-2 008-536-070 Mounted in field. See chapter 4.
DVI-RGB Conversion Kit
OP03-180-3 008-545-610 Mounted in console at factory.
OP03-180-4 008-545-600 Mounted in console in field.
XH10P-W-6P L=20M 000-149-748 20 m Between control &
XH10P-W-6P L=30M 000-149-749 30 m processor unit
XH10P-W-5P-A
000-149-050 10 m
L=10M
XH10P-W-5P-A Between control
000-149-051 20 m
Cable Assy. L=20M units
XH10P-W-5P-A
000-149-052 30 m
L=30M
DVI-D/D S-LINK 10M 000-150-200 10 m Monitor-Processor
S03-9-5 008-206-640 For external radar, 5 m, 8-8P
iv
FR-FTPC-CY
OP03-28900 000-082-658
10 m Modular
FR-FTPC-CY connection
LAN Cable Kit (with armor) OP03-28910 000-082-629
20 m MPS588-C,
FR-FTPC-CY 2 pcs.
OP03-28920 000-082-660
30 m
FP03-09820 008-535-560 Hanger assy. for MU-201CR
Accessories
FP03-09830 008-536-020 Hanger assy. for MU-231CR
Hand Grip FP03-09840 008-535-570 For monitor unit
03-163-1201 100-307-260 For MU-201CR
Dust Cover
03-163-2101 100-307-270 For MU-231CR
FP03-11500 001-020-090 For MU-201CR
Hood
FP03-11000 008-571-680 For MU-231CR
Clamp Plate OP03-182 008-535-620 For RCU-014
FP03-09870 008-535-630 For control unit
Flush Mount Kit
OP03-198 001-008-050 RCU-016/014/015
OP03-183 008-535-640 For RCU-014&MU-201CR
Coupling Pedestal OP03-184 008-535-650 For RCU-014& MU-231CR
OP03-185 008-535-660 For RCU-014
BNC Connector Converter DSUB-BNC-1 000-148-528 For VDR
For more than 100m
Junction Box RJB-001 -
antenna cable
Desktop Mount Kit FP03-10201 008-539-530 For CU-200
Console Mount Kit FP03-10202 008-539-540 For CU-200
Switching Hub HUB-100 - See manual of HUB-100.
Slim Hood FP03-11010 001-033-140 For MU-231CR display unit
FP03-11510 001-034-390 For MU-201CR display unit
About the category sticker

This radar meets the requirements in IEC62388 (Marine navigation and
radiocommunication equipment and systems – Shipborne radar – Performance
requirements, method of testing and required test results)
Check the appropriate box on the sticker which is pre-attached on the processor unit,
according to your radar’s specification. Refer to the table shown below to confirm your
category.
Category Radar type ANT. rotation speed
FAR-2817, FAR-2827, FAR-2837S, Normal speed
CAT 1
FAR-2827W, FAR-2837SW
CAT 1H FAR-2817, FAR-2827, FAR-2837S HSC
FR-2117/BB, FAR-2127/BB, Normal speed
CAT 2
FAR-2137S/BB
FAR-2117/BB, FAR-2127/BB, HSC
CAT 2H
FAR-2137S/BB
v
SYSTEM CONFIGURATION
Performance Monitor
*
MONITOR UNIT
ANTENNA UNIT MU-201CR,

JB ** MU-190
FAR-2117/2817: XN12AF-RSB-096-078A (2117/2127)
XN12AF-RSB-097-078A or
XN20AF-RSB-096-078A MU-231CR,
MU-231 24 VDC
XN20AF-RSB-097-078A (2817/2827)
XN24AF-RSB-096-078A RU-3423
XN24AF-RSB-097-078A
FAR-2127/2827: XN12AF-RSB-096-079A CONTROL UNIT
XN12AF-RSB-097-079A RCU-014 100/110/115
XN20AF-RSB-096-079A (Standard) 220/230 VAC
XN20AF-RSB-097-079A or
XN24AF-RSB-096-079A RCU-015 24 VDC
XN24AF-RSB-097-079A JB** (Trackball) or
100-230 VAC
EPFS 1) Control Unit
IEC-61162 Serial Data PROCESSOR UNIT RCU-016
(Navigator) (Remote)
(Input/Output) RPU-013
SDME 2)
(Speed Log) IEC-61162 Serial Data
(Input) Sub Display
3)
Gyro Converter Alarm***
Gyrocompass
GC-10
VDR
AD-100
AIS Switching HUB
HUB-100
Track Control Unit
External Monitor
MEMORY CARD AC spec

INTERFACE UNIT DC spec
CU- 200-FAR
Rectifier
RU-3424 Transformer Unit
: Standard RU-1746B-2 RU-1803
: Option
: Dockyard supply
Category of Units
Antenna Unit: Exposed to weather
All other units: Protected from weather
1) Connect the EPFS which is approved in accordance with the requirements of the IMO in
resolution MSC.112(73) is used.
2) Connect the SDME which is approved in accordance with the requirements of IMO in
resolution MSC.96(72) is used.
3) Use the gyrocompass having an update rate that is adequate for the ship’s rate of turn.
*: For FAR-2117-BB/2127-BB a monitor unit is prepared by user. See page 1-6.
These monitors have been approved by the IMO, MU-201CR for CAT 2, MU-231CR for
CAT 1. If a different monitor is to be used, its effective diameter must meet the applicable
Category requirements: CAT 1: effective diameter 320 mm or higher, CAT 2: effective
diameter 250 mm or higher. Refer to their operator’s manuals for details.
**: Junction boxes are required for more than 100 m antenna cable.
***: Contact output for Alarm
(Load current) 120 mA (Polarity) No.1, 2: Normally Close, No.3, 4: Normally Open
Serial I/O for alarm is also possible, which complies with IEC 61162-1.
vi
1. MOUNTING
NOTICE
Do not apply paint, anti-corrosive sealant
or contact spray to coating or plastic
parts of the equipment.
Those items contain organic solvents that

can damage coating and plastic parts,
especially plastic connectors.
1.1 Antenna Unit

Mounting considerations
• The antenna unit is generally installed either on top of the wheelhouse or on the radar
mast, on a suitable platform. Locate the antenna unit in an elevated position to permit
maximum target visibility.
• A line of sight from the antenna unit to the bow of the ship should hit the surface of the
sea in not more than 500 m or twice the ship’s length, depending which value is smaller,
for all load and trim conditions.
less than 500 m or twice the ship’s length
• Mount the antenna unit so that any blind sectors caused by objects (mast, etc.) are kept
to a minimum. No blind sector should exist in arc of the horizon from right ahead to 22.5°
aft of the beam to either side (see Figure 1 below). Also, individual blind sectors of more
than 5°, or the total arc of both blind sectors of more than 20°, should not occur in the
remaining arc (Figure 2). Note that any two blind sectors separated by 3° or less are
regarded as one sector.
270 90
a, b, c: less than 5 respectively

22.5 22.5 a+b+c+... : less than 20
less than 3
Figure 1 Figure 2
1-1
1. MOUNTING
• Install the antenna unit away from interfering high-power energy sources and other
transmitting radio antenna.
• Keep the lower edge of the antenna unit above the safety rail by 500 mm or more.
• Two antenna units should be mounted as below:
more than 20
more
than 1 m
• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in
the bow direction, especially zero degrees ±5°, to prevent blind sectors and false echoes
on the radar picture.
• It is rarely possible to place the antenna unit where a completely clear view in all
directions is available. Thus, you should determine the angular width and relative bearing
of any shadow sectors for their influence on the radar at the first opportunity after fitting.
• Locate a direction finder antenna clear of the antenna unit to prevent interference to the
direction finder. A separation of more than two meters is recommended.
• A magnetic compass will be affected if the antenna unit is placed too close to the
magnetic compass. Observe the compass safe distances on page ii to prevent deviation
of the magnetic compass.
• Do not paint the radiator aperture, to ensure proper emission of the radar waves.
• The antenna base is made of cast aluminum. To prevent electrolytic corrosion of the
antenna base, use the seal washers and corrosion-proof rubber mat and ground the unit
with the ground wire (supplied).
• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial
performance and hot gases may distort the radiator portion. The antenna unit must not be
mounted where the temperature is more than 55°C.
• Leave sufficient space around the unit for maintenance and servicing. See the antenna
unit outline drawing for recommended maintenance space.
1-2
1. MOUNTING
Assembling the antenna unit

The antenna unit consists of the antenna radiator and the antenna unit chassis, and they
are packed separately. Fasten the antenna radiator to the antenna unit chassis as follows:
1. For the XN20AF, XN24AF, attach two guide pins to the underside of the antenna
radiator.
2. Remove the waveguide cap from the radiator bracket. The cap may be discarded.
3. Coat the waveguide flange with anticorrosive sealant as shown below.
10 mm O-ring Waveguide cap
Hole for Hole for

a guide pin a guide pin
5 mm
Anticorrosive sealant
Coating the waveguide flange with anticorrosive sealant
4. Coat fixing holes for the antenna radiator with anticorrosive sealant.
5. Grease the O-ring and set it to the O-ring groove of the radiator flange.
6. Set the antenna radiator to the radiator bracket.
7. Coat hex bolts M8x40 (for XN-20AF or XN-24AF) or hex bolt M8x35/ flat washer/spring
washer (for XN-12AF) with anticorrosive sealant and use them to loosely fasten the
antenna radiator to the antenna unit chassis.
8. Remove two guide pins (inserted at step 1), and then tighten fixing bolts.
CAUTION
Be sure to remove the guide pins.
Injury may result if the guide pins loosen

and fall.
1-3
1. MOUNTING
Antenna radiator
Waveguide
Radiator bracket
Guide pin
(XN20AF,
XN24AF Hex bolt (M8x40), 8 pcs.
only) (XN20AF, XN24AF)
Hex. bolt (M8x35), 8 pcs.
Flat washer
O-ring Spring washer (XN12AF)
Fastening the radiator to the radiator bracket

Fastening the antenna unit to the mounting platform
The antenna unit may be assembled before hoisting it to the mounting platform. However,
do not lift the antenna unit by the radiator. Always hold the unit by its housing. When using a
crane or hoist, lift the unit by the hoist rings which should be fastened to the bolt fixing
covers of the antenna housing.
NOTICE
- To hoist antenna unit aboard vessel, attach ropes to lifting fixtures and hoist unit with crane.
- To remove load from radiator when hoisting, the length of the rope between the radiator base
and the hook on the should be at least 130 cm.
- To keep the rope away from the radiator, turn the radiator and chassis approx. 30 degrees as
shown below.
- Be sure to remove the lfiting fixtures after hoisting is completed.
Lifting NO! NO!

fixture
130cm
Crane
Lifting fixture
Approx.
30 deg.
Lifting fixture
(Top view)
1. Construct a suitable mounting platform referring to the outline drawing at the end of this
manual.
2. Drill four mounting holes of 15 mm diameter and one cable entry hole of about 50 mm
diameter in the mounting platform.
3. Lay the rubber mat (supplied) on the mounting platform.
4. Place the antenna unit on the rubber mat, orienting the unit so the bow mark on its base
1-4
1. MOUNTING
4. Place the antenna unit on the rubber mat, orienting the unit so the bow mark on its base
is facing the ship’s bow.
Ground
terminal
Rubber
mat
Bow mark
Antenna unit, front view
5. Fasten the antenna unit to the mounting platform with M12x60 hex bolts, nuts, flat
washers and seal washers.
6. Using hex bolt (M6x25), nut (M6) and flat washer (M6), establish the ground system on
the mounting platform as shown below. The location should be within 340 mm of the
ground terminal on the antenna unit. Connect the ground wire (RW-4747, 340 mm,
supplied) between the grounding point and ground terminal on the antenna unit. Coat
the entire ground system with silicone sealant (supplied).
Ground wire Hex bolt

Anticorrosive sealant Spring washer
Seal washer
Rubber mat
Spring washer
Anticorrosive Hex nut
Anticorrosive sealant OR
sealant
Ground wire Hex nut
Spring washer
Flat washer
Hex bolt welded to

ship's superstructure
Anticorrosive sealant
Ground
terminal
Ground
wire
Antenna base
How to mount the antenna unit
1-5
1. MOUNTING
1.2 Monitor Unit

The monitor unit can be flush mounted in a console panel, or mounted on a desktop using
the optional accessories. For MU-190/231, see the applicable Operator’s Manual(s).
Note: FAR-2117-BB/2127-BB have no monitor unit. Prepare a suitable monitor locally.

Recommended monitor: SXGA (1280x1024), aspect ratio 5:4
When selecting a mounting location, keep in mind the following points:
• Select a location where the display unit can be viewed conveniently and where the
screen can be viewed while facing towards the bow.
• The optimal viewing distances for the radar display units are: MU-170C: 920 mm,
MU-201CR: 1080 mm, MU-231CR: 1200 mm. Select a suitable mounting location
considering the applicable distance.
• Locate the unit out of direct sunlight and away from heat sources because of heat that
can build up inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Leave sufficient space on the sides and rear of the unit to facilitate maintenance.
• A magnetic compass will be affected if the monitor unit is placed too close to the magnetic
compass. Observe the compass safe distances on page ii to prevent deviation of a
magnetic compass.
Mounting procedure
Flush mounting
Follow the procedure below to mount the monitor unit in a console panel.
1. Make cutout in mounting location referring to the outline drawing shown below.
2. Insert the monitor unit to the hole and fix it with four tapping screws (6x30).
3. Attach panel hooks near the fixing holes (upper part). See next page. These are used to
pull out the monitor unit from a console panel for servicing.
4. Attach four panel covers to the fixing holes.
506±1 4-FIXING HOLES
296±1
296±1
420
454
(79)
490 506±1 4-φ8

534 FIXING HOLES
30 80
Monitor unit MU-201CR

(For FAR-2117/2127)
1-6
1. MOUNTING
570±1 4-φ8 FIXING HOLES

4-FIXING HOLES
313±1
313±1
471
505
(96)
554 570 ±1
598
30 80
Monitor unit MU-231CR

(For FAR-2817/2827)
Flush mounting of monitor unit
Panel hook
Panel cover
Fixing screw
Attaching panel hook and panel cover
Note: If you need to remove the monitor unit from the mounting panel, remove the four
panel covers with your fingernail and use two panel hooks supplied as accessories to
lift the monitor unit.
1-7
1. MOUNTING
Desktop mounting
Use the optional accessories to mount the monitor unit on a desktop.
• For FAR-2117/2127: FP03-09820 (Code No.: 008-535-560)
• For FAR-2817/2827: FP03-09830 (Code No.: 008-536-020)
Contents of FP03-09820/09830
Name Type Code No. Qty Remarks
Hanger L 03-163-1111 100-305-141 1
Hanger R 03-163-1112 100-305-181 1
03-163-1113 100-305-191 For FAR-2117/2127
Hanger stay 1
03-163-2071 100-305-371 For FAR-2817/2827
Hole plug CP-30-HP-13 000-160-074-10 2
Plastic rivet KB-13 Rivet Black 000-570-276-10 4
Hex. bolt M6x25 000-162-949-10 4
Hex. bolt M10x30 000-162-884-10 2
Spring washer M10 000-864-261 2
Flat washer M10 000-864-131 2
1. Assemble two hangers and hanger stay with two hex bolts (M10x30), flat washers and
spring washers and cover each hex bolt with hole plug.
2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard
supply).
3. Fasten the monitor unit to the mounting hanger assembly with four hex bolt (M6x25,
supplied).
4. Cover each hex bolts with panel cover.
5. Cover each holes for hand grip on the hangers with plastic rivets (4 pcs).
1-8
1. MOUNTING
Hanger (L)
M12 bolts for fixing

(Dockyard supply)
Hanger stay Hanger (R)
Panel cover
Plastic rivet
Hex bolt Flat Washer M10
(M6x25) Spring Washer M10
Hex bolt
M10x30
Hole plug
Panel cover
To remove this, insert fingernail in groove.

Monitor Unit
The hand grip is optionally available for the desktop mounting monitor unit.
Wave washer
Rosette washer
Screw
Handle
Hood (option)
When it is too bright in the daytime, use the optional hood to shade the screen.
• For FAR-2117/2127: FP03-11500 (Code No.: 001-020-090)
• For FAR-2817/2827: FP03-11000 (Code No.: 008-571-680)
Contents of hood
Name Type Code No. Qty. Remarks
Hood (21) FP03-11501 001-020-120 1 For FAR-2117/2127
Hood (23) FP03-11001 008-571-700 1 For FAR-2817/2827
Fixing plate 03-163-2202-0 100-335-560-10 4
Screw M4x10 D=13 US304 000-862-543 4
1-9
1. MOUNTING
1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts
(supplied).
Flush mounting: Fasten the display unit to the mounting location, and then attach the
fixing plates with four self-tapping screws.
Hex head bolt
Fixing plate
Fixing hole
2. Attach the hood to the display unit (the hood is outside of the fixing plates).
3. Fasten the hood to the fixing plates with four screws supplied (M4x10).
1.3 Control Unit

The control unit may be mounted on a desktop, with or without the KB fixing metal
(supplied), which mounts the control unit at an angle.
• Select a location where the control unit can be operated conveniently.
• Locate the unit away from heat sources because of heat that can build up inside the
cabinet.
• Determine the mounting location considering the length of the signal cable between the
control unit and the processor unit. (The 10m signal cable is attached to the control unit).
• A magnetic compass will be affected if the control unit is placed too close to the magnetic
magnetic compass.
1-10
1. MOUNTING
Fixing with KB fixing plate

1. Fix the KB fixing plate to the bottom of the control unit.
2. Attach cushions (three for RCU-014, two for RCU-015/016) to the bottom of the control
unit as shown below.
3. Fix it to a desired location with self-tapping screws (local supply).
KB fixing plate Cushion
Side view for RCU-014/015/016

Fixing without KB fixing metal
1. Drill four mounting holes of 5 mm diameter referring to the outline drawing at the back of
this manual.
2. Fix the control unit with four screws (M4) from under side of the desktop. (The M4
screws with a sufficient length for the thickness of the desktop should be provided
locally.)
#70
136±1
180
4-M4 (Fixing holes)

308±1 (bottom)
398
Control Unit RCU-014
24 32
F1
136±1
180
F2
F3
F4
110±1 4-M4 (Fixing holes)

160 (REAR)
RCU-015/016
1-11
1. MOUNTING
Flush mounting
Use the optional flush mount kit FP03-09870 to mount the control unit RCU-014, RCU-015
and/or RCU016 to a console panel.
Name: Flush mount kit

Type: FP03-09870
Code No.: 008-535-630
No. Name Type Code No. Qty
1 Mount plate 03-163-7531 100-306-261 4
2 Hex nut M5 000-863-108 4
3 Wing screw M5x40 000-162-682-10 4
4 Pan head screw M4x12 000-163-192-10 4
1. Prepare a cutout in the mounting location as shown in the figure below.
170±2 176±2
388 ±2 150±2
For RCU-014 For RCU-015 and RCU-016
2. Set the control unit to the cutout.

3. Attach the mounting plate to the control unit with four screws from the rear side.
4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing
screw.
5. Fasten each wing screw and then fasten the hex nuts as shown in the figure below.
#70
#70
(P)
53
53
(P)
86
92
171
Note: P <
=10
RCU-014 RCU-015/RCU-016
1-12
1. MOUNTING
To connect RCU-016 in series with RCU-014
1. Pass the cable derived from RCU-016.
2. Connect the connector

of the cable to J502.
3. Clamp the copper part of the cable with the cable clamp.
Inside of RCU-014
1-13
1. MOUNTING
To change the cable entry

To change the cable entry from the side (default) to the bottom, modify the unit as shown
below.
Screw Bottom of the unit

M3x8
2. Pull out the cable.
3. Pass the cable from this hole. Cable clamp

03-163-7804
Screw
M4x8
4. In here, clamp the copper part
of the cable with the cable
clamp removed at step1. 1. Remove the
cable clamp.
4
2
J5
12
J5
J522: If you connect RCU-016 in series with RCU-015, plug in here.

RCU-015/016: Changing cable entry
1-14
1. MOUNTING
1.4 Processor Unit

• Locate the processor unit away from heat sources because of heat that can build up
inside the cabinet.
• Leave sufficient space at the sides and rear of the unit to facilitate maintenance.
• A magnetic compass will be affected if the processor unit is placed too close to the
magnetic compass. Observe the compass safe distances on page ii to prevent deviation
of a magnetic compass.
Mounting procedure
1. Fix the unit with four M6 bolts, or self-tapping screws.
2-φ7 FIXING HOLES
#50
385 25
370±1
340±1
380
410
R3
.5
7
350±1 2-FIXING NOTCH
Floor mounting or bulkhead mounting

Note: If you fix the unit, cable entry upside, never remove the screw M3x10 that joints
the upper case assy. and lower case assy. of the processor unit.
Upper case assy.
Lower case assy.
Screw
M3x10
Never remove this screw.
Processor unit
1-15
1. MOUNTING
This page is intentionally left blank.
1-16
2. WIRING
Wiring consideration
• To lessen the chance of picking up electrical interference, avoid where possible routing
the signal cable near other onboard electrical equipment (radars, transmitting radio
antennas, etc.) Also avoid running the cable in parallel with power cables. When crossing
with other cable, the angle should be 90°to minimize the magnetic field coupling.
• The signal cable run between the antenna and processor units is available in lengths of
15 m (standard), 30 m and 50 m. Whatever length is used it must be unbroken; namely,
no splicing allowed. Use the signal cable as short as possible to minimize attenuation of
the signal.
• The radar should be connected to an emergency power source, as required by SOLAS
II-1.
2.1 Interconnection
Antenna unit
Monitor unit
TB801
TB802
Junction Box
RJB-001*
RW-9600
15/30/40/50 m
(Max.100 m)
DVI-D/D SINGLE LINK 5M, 5/10 m
DPYC-2.5
Processor unit Control unit
(RCU-014 or RCU-015)
Memory
Card
I/F Unit
CU-200-FAR
24 VDC or XH10P-W-5P-A
100-230 VAC L=10/20/30m
Junction Box Control unit

XH10P-W-6P L=1.5/10/20/30m*
RJB-001* (RCU-016)
DPYC-2.5 for AC set
DPYC-6 for DC set
F1
24 VDC or F2
F3
F4
100-115 VAC/220-230 VAC

*: If the length of the antenna cable is more than 100m,
use Junction box RJB-001. However, the maximum length is 300m.
: Cable requires fabrication
Standard Interconnection
2-1
2. WIRING
2.2 Antenna Unit
NOTE
The magnetron in the transceiver module will de-
magnetize if it contacts ferrous material. When
dismounting the transceiver module, lay it on its
side or on top of non-ferrous material as shown
below.
Transceiver module
(magnetron inside)
Non-ferrous
block
Height more
than 5 cm
1. Open the rear cover of the antenna unit

2. Disconnect plugs P823, P803, P831 and P921. If the PM-31 is installed, also disconnect
plug P911.
3. Unfasten two bolts and remove the transceiver module.
Fixing
bolts
Transceiver module
Antenna unit, rear view
4. Unfasten the four fixing bolts from the cable gland at the base of the antenna unit.
Remove clamping ring, rubber gasket and washers.
5. Pass the signal cable through the cable entry hole in the antenna unit mounting platform.
Trim the cable so about 80 cm of it protrudes past the cable gland.
2-2
2. WIRING
Antenna unit, front view, cover removed
500mm
6. Fabricate the signal cable RW-9600
as shown below. Vinyl sheath
a) Remove the outer vinyl sheath, by
about 500 mm, then armor and 30mm
inner sheath by about 470mm.
b) Unravel the shield to expose the
core wires.
c) Trim each core wire (except Armor sheath Shield
coaxial wire) considering its
location on the terminal board.
Shield
d) Trim the shield leaving about 500
mm and attach crimp-on lug
FV5.5-4 (yellow, I4).
e) Remove insulation of each wire by
about 6 mm. 6
7. Slide a washer, and fold back armor.

Slide a washer, rubber gasket, 14 5 9
washer, and clamping ring in order.
Cut the armor around the washer so Conductor
it is level with the washer. Fold back shield.
Shield
Coaxial cable
2-3
2. WIRING
8. Nip the armor between two washers, and trim the excess armor from around washers.
And then pass the shield between the clamping ring and the washer as shown below.
Fasten the clamping ring with the screws.
4-M4x16
Clamping ring
Washer
Shield
Rubber gasket (25B)
Armor
Signal cable entrance
9. Connect the signal cable to the terminal board TB801 and TB802 on the RFTB board
03P9349 by referring to the interconnection diagram. Keep “slack” in the coaxial wire to
prevent breakage. Insert the cores (except coaxial wire) to the connector with the opener.
Opener
1. Insert opener.
2. Push opener.
3. Insert a core.
4. Release opener.
Clamp the coaxial wire with cable clamp on the board 03P9349 as shown below.
Clamp shield with bracket.
Tighten conductor with screw.
10. Bind cable cores with cable ties.
2-4
2. WIRING
11. Set the transceiver module to the antenna unit, push it in until it stops, and then tighten
fixing bolts (4 pcs.). Connect plugs P823, P803, P831, P921 and J911 (if installed).
Fasten the shield wire to the wing nut on the transceiver module.
CAUTION
Push in transceiver unit until it stops.
Failure to do so may cause leakage of

microwaves.
Clamp for
coaxial cable
03P9349
Connect coaxial cable here.
Transceiver module
Connector Signal cable

plug
Connect shield wire to with wing
Cable clamp for Bow mark nut at the opposite side of the
antenna cable transceiver module.
Antenna unit, front view
12. Confirm that all screws are tightened and all wiring is properly made. Confirm that
waterproofing gasket, bolts and tapping holes of antenna unit are coated with silicone
grease. Close the antenna unit cover (torque: 2.5 N·m).
2-5
2. WIRING
2.3 Monitor Unit

Two cables are terminated at the display unit: the signal cable from the processor unit (5 m
or 10 m cable) and the power cable from the ship’s mains. The signal cable comes with a
connector preattached to it for connection to the monitor unit. Fabricate the power cable as
below. Use DPYC-2.5 (Japan Industry Standard) cable or the equivalent.
For MU-190/231, see the applicable Operator’s Manual(s).
Fabricating the power cable

1. Cut armor of the cable by 40 mm.
2. Cut vinyl sheath by 35 mm.
3. Remove insulation of wires by about 10 mm. Fix crimp-on lugs to the cores.
4. Peel paint of the armor by 40 mm.
5. Cover the end of armor with vinyl tape.
(a) DPYC-2.5
Approx. 40 mm
Armor
35 mm
(b)
Vinyl sheath
10 mm
Armor
(c)
40 mm: Peel paint. Conductor

2
S = 2.5 mm
(d) φ = 2.01 mm
Taping (sectional view)
Fabricating power cable DPYC-2.5
MU-201CR MU-231CR
Cable entrance for signal cable

(The connector with no EMI core
should be connected to the monitor unit.)
Cable entrance for power cable
Monitor unit (rear panel)
2-6
2. WIRING
2.4 Processor Unit

Four cables are terminated at the processor unit: the antenna unit cable, display unit cable,
control unit cable and the power cable. Cables other than the power cable come with a
connector preattached to them for connection to the processor unit. Fabricate the power
cable as below. For the power cable, use DPYC-2.5 (Japan Industry Standard) cable for AC
unit or DPYC-6 for DC unit, or the equivalent.
Note: For AC unit
Pass the AC line through a double-contact breaker (shipyard supply).
Fabricating the power cable

1. Cut armor of the cable by 40 mm.
2. Cut vinyl sheath by 35 mm.
3. Remove insulation of wires by about 10 mm. Fix crimp-on lugs to the cores.
4. Peel paint of the armor by 40 mm.
5. Cover the end of armor with vinyl tape.
(a) DPYC-2.5
Approx. 40 mm
Armor
35 mm
(b)
Vinyl sheath
10 mm
(c)
40 mm: Peel paint.
(d)
Taping
Armor
Conductor of DPYC-2.5
S = 2.5 mm 2
φ = 2.01 mm
Conductor of DPYC-6
2
S = 6.0 mm
φ = 3.12 mm
(sectional view)
Fabricating power cable DPYC
2-7
2. WIRING
Connection of cables
The power cable is connected to the terminal board on the rear panel and the signal cable
from the monitor unit is connected to the DVI-D connector. Other cables are connected to
the printed circuit board 03P9342.
Monitor unit Power cable clamp
* Power cable terminal board
Network DVI-D monitor
Remove the
protection cover.
F70
FUSE
15
1
DC/AC F1
2
Control unit**
Heading senor
Power cable Speed log
Navigator
21 2 3 4 5 6 18 19 20
9 14 17 HDG RSD
φ9
ACK
φ18.9
24 24’ 26
1 7 8 28 φ7.4
VDR IN
φ7
VDR OUT
GYRO PSU004
AIS AD100
Memory Card IF unit

Cable clamp Antenna unit VDR OUT
GND TERMINAL
VDR IN
Gyrocompass
AD-100
AIS
Processor unit
*: The connector with EMI core should be connected to the processor unit.
**: The configuration of optional cable between the processor unit and the
control unit is as follows. Note that the cable fabrication for each end is
different.
Control unit Processor unit

150 mm 1.5/20/30 m 300 mm
Cable XH10P-W-6P L=20/30M
When the RCU-016 is installed, optional cable (XH10P-W-5P-A, L=10/20/30M) is required.

Cable fabrication for each end is the same.
Control unit Processor unit

150 mm 10/20/30 m 150 mm
XH10P-W-5P-A L=10/20/30M
2-8
2. WIRING
Location of connectors
Open the processor unit as follows and the 03P9342 board appears.
Cable clamp
03P9342
J621 J612 J608

Gyro converter board
J607 or AD-100
External alarm Speed log
J620
J606
Track control J611 Navigator
AIS
J619 J605 J603
ECDIS
Gyro converter board
J604 Heading sensor
To Sub display * J618 J610 J602
(SEMI-LOG) PSU
J617 Cable from the
To Sub display * control unit
(FULL-LOG) J616
From Master radar Cable from antenna unit
J614 J615 J601
+12V for card I/F
J613 J609 PC
J654
Tx HV line
Coaxial wire
03P9342
*: See page 2-11 for details.
2-9
2. WIRING
Cable fabrication for the cables connected to the 03P9342 board

x Signal cable RW-9600 (Between antenna unit and processor unit)
Vinyl sheath Armor Shield
60 450
Vinyl tape After exposing cores,

wind shield around the armor.
6
14 5 9
Coaxial cable Conductor

Fold back shield.
Clamp here by cable clamp.
Coaxial cable
x Other cables for optional units

Use TTYCS-1 or TTYCS-4 (Japan standard cable) or equivalent.
Armor φ = 16.3 mm
Armor
Sheath
Sheath
Shield Shield
φ = 10.1 mm
Conductor Conductor
S = 0.75 mm 2 S = 0.75 mm 2
φ = 1.11 mm φ = 1.11 mm
TTYCS-1 TTYCS-4
Armor 60: Peel paint.

Shield
L= Depends on equipment
L connected. Measure at
the processor unit.
5
After exposing cores,
Vinyl tape
wind shield around the armor.
Clamp here by cable clamp.
Wiring for WAGO connector Wiring for Coaxial cable

Press downward. Clamp shied with bracket.
Terminal opener
Wire
WAGO connector Tighten conductor with screw.
Twist
Procedures
1. Twist the conductor. CAUTION
2. Press the terminal opener downward.
3. Insert the wire to hole. Do not use crimp-on lug to prevent
4. Remove the terminal opener. contact resistance from increasing.
5. Pull the wire to confirm that it is ecure.
2-10
2. WIRING
Connection of Sub-display
A conventional remote display and/or FAR-2107 series radar can be connected to J617 and
J618 in the processor unit as a sub-display. However, the control for GAIN and STC are
different depending on J617 and J618. Refer to the table to connect sub-displays.
Port Conventional remote FAR-2107 series radar

display
J617 Overall gain Even if input video level is The gain is 8 dB lower than
adjusted to 4 Vp-p, the that on the master radar.
(FULL-LOG)
gain is 8 db lower than
that on the master radar.
GAIN control The GAIN control is The GAIN control has no

effective. effect.
STC control The STC control is The STC control has no

effective. effect.
J618 Overall gain When input video level is The gain is almost same as
adjusted to 4 Vp-p, the that on the master radar.
(SEMI-LOG)
gain becomes the same
as that on the master
radar.
GAIN control The GAIN control is The GAIN control has no

effective. effect.
STC control The STC control is The STC control has no

effective, however this effect.
control is added on the
signal adjusted by the
master radar. So this port
is not recommended to
use.
2-11
2. WIRING
2.5 Changing AC Power Specification of Processor

Unit
To change AC power specification between 100 VAC and 220 VAC, add or remove jumper
connector P108 on the PWR board 03P9339 and change the fuse on the processor unit
according to ship’s mains as shown in the table below. The figures below and on the next
page show the location of the fuse and the jumper connector on the PWR board. Also,
adjustment of the overvoltage detection circuit is required.
Note: To change from 200 VAC to 100 VAC, locally prepare the jumper connector, referring
to the figure shown on the next page (VH8P connector housing is fitted at J108).
Power supply Fuse Jumper connector

100 VAC 10A Added
220 VAC 5A Removed
Cover of PWR board
Fuse
PWR board
Upper part of processor unit

(SPU assembly omitted)
2-12
2. WIRING
J105 J106 (P)HV
PWR board J104
J103
R21
(OVER)
J101
P108/J108
AC FIL
87654321
Jumper connector
(VH8P)
How to adjust the overvoltage detection circuit:

1. Add or remove the jumper connector P108 and change the fuse.
2. Rotate R21 fully clockwise on the PWR board.
3. Connect a variable transformer between ship's mains and the input power terminal board
TB-1 of the processor unit.
4. Adjust the variable transformer output (i.e., input voltage to the processor unit) as follows.
For 100 VAC set: 144 VAC
For 220 VAC set: 288 VAC
5. Turn on the radar and rotate the R21 counterclockwise gradually until the overvoltage
detection circuit functions (i.e., power supply cuts off).
6. Lower the output voltage of the variable transformer and confirm that the radar
automatically turn on with a voltage lower than 142VAC or 284VAC.
7. Gradually increase the output voltage of the variable transformer and confirm that the
overvoltage detection circuit functions at 144V or 288VAC of the variable transformer
output.
8. Assemble and connect the processor unit.
2-13
2. WIRING
2-14
3. SETTING AND ADJUSTMENT
3.1 DIP Switch Setting
The processor unit is shipped for model FAR-2117 or FAR-2127. If your model is
FAR-2817/2827/2117-BB/2127-BB, change the DIP switch setting as follows.
1. Remove the top cover of the processor unit.
2. Open the SPU assembly block.
Shield cover
SPU assembly block
SPU board 03P9337
DIP switch S1
3. Set the DIP switch S1 as follows.
OFF S1 Monitor SXGA for Monitor UXGA for FAR-2117-BB

ON FAR-2117, 2127 FAR2817, 2827
1 FAR-2127-BB
(Default) (MU-231CR
2 S. No. 0269 and later)
3 1 OFF ON OFF
4 2 OFF OFF ON
3
S1 Not used.
4
Note: Set #1 and #2 of S1 to OFF for MU-231CR S. No. 0268 and earlier.
3-1
3.2 Initializing Tuning

1. Transmit the radar on 48 nm range and rotate the GAIN knob to show 70-80 of the gain
bar.
2. Roll the trackball to choose the MENU box at the right side of the screen and then push
the left button.
3. Roll the wheel to choose 1 ECHO and then push the wheel.
[ECHO]
1 BACK
2 2ND ECHO REJ
OFF/ON
3 TUNE INITIALIZE
4 PM
OFF/ON
5 SART
OFF/ON Bold: Default settings
6 WIPER
OFF/1/2
(Same for all menu illustrations)
7 ECHO AREA*
CIRCLE/WIDE/ALL *: non IMO-type only
8 [PICTURE SELECT]
9 STC RANGE
+00
ECHO menu
4. Roll the wheel to choose 3 TUNE INITIALIZE.

5. Push the wheel to initialize automatic tuning.
After a while, echoes appear on the screen. The message “TUNE INITIALIZE” appears in
red during automatic tuning. When this message disappears, the tuning is completed. If
necessary adjust the GAIN to show echoes clearly.
6. Push the right button twice to close the menu.
3-2
3.3 Heading Alignment

You have mounted the antenna unit facing straight ahead in the direction of the bow.
Therefore, a small but conspicuous target dead ahead visually should appear on the
heading line (zero degrees).
In practice, you will probably observe some small bearing error on the display because of
the difficulty in achieving accurate initial positioning of the antenna unit. The following
adjustment will compensate for this error.
Correct bearing α
relative to heading
350 000 010
α Target 320
330
340 020
030
040
310 050
300 060
290 070
280 080
270 090
260 100 Apparent

250
240
110
position
230 130
120
of target
220 140
210 150
200 160
190 180 170
Antenna mounted error Picture appears

to port (HDG SW deviated clockwise.
advance)
Apparent position β
of target
β
000
Target 320
330
340
350 010
020
030
040
310 050
300 060
290 070
280 080
270 090
260 100 Correct

250
240
110
bearing
230
120
130
relative to
220
210
200 160
150
140
heading
190 180 170
Antenna mounted error Picture appears

to starboard (HDG deviated counterclockwise.
SW delayed)
Heading alignment
1. Select a stationary target echo at a range between 0.125 and 0.25 nm, preferably near
the heading line.
2. Operate the EBL control to bisect the target echo.
3-3
3. Read the target bearing.

4. Measure the bearing of the stationary target on the navigation chart and calculate the
difference between actual bearing and apparent bearing on the radar screen.
5. Press the [MENU] key to show the main menu.
6. While pressing and holding down the [HL OFF] key, press the [MENU] key five times.
7. Press the [0] key to show the [INITIALIZE] menu.
[INITIALIZE]
1 BACK
2 [ECHO ADJ]
3 [SCANNER]
4 [INSTALLATION]
5 [OWN SHIP INFO]
6 [TT PRESET]
7 [NETWORK]
8 [OTHER]
9 [FACTORY]
Note: See next page to access the INITIALIZE menu with the trackball style control unit
RCU-015.
8. Press the [2] key to open the [ECHO ADJ] menu.

[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu

9. Press the [3] key to choose the HD ALIGN option.
10. Key in the bearing difference. The setting range is 0 to 359.9°.
11. Confirm that the target echo is displayed at correct bearing on the screen.
12. Press the [MENU] key to finish.
3-4
How to Access the Installation Mode with the RCU-015 Trackball Style
Controller
1. By using the trackball,

move the pointer until
it highlights the MENU
box as shown. DO
NOT CLICK the menu
box, just leave the
arrow over the menu.
2. Press and hold down

the F1 key. Keep it
held down during the
next step.
3. Then, click on the right

controller button 5 times.
You should hear a “triple
Beep” on the fifth press.
The INITIALIZE menu will

appear. Click on
INSTALLATION to access
the installation menus.
3-5
3.4 Adjustment Sweep Timing

Sweep timing differs with respect to the length of the signal cable between the antenna unit
and the processor unit. Adjust sweep timing at installation to prevent the following
symptoms:
• The echo of a “straight” target (for example, pier), on the 0.25 m range, will appear on the
display as being pulled inward or pushed outward. See Figure below.
• The range of target echoes will also be incorrectly shown.
(1) Correct (2) Target pushed (3) Target pushed

inward outward
Examples of correct and incorrect sweep timings
1. Transmit on the 0.25 nm range.

2. Adjust radar picture controls to display picture properly.
3. Select a target echo which should be displayed straightly.
4. Press the [4] key to choose the [TIMING ADJ] on the [ECHO ADJ] menu.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
5. Rotate the wheel to set a suitable value which causes the target to be displayed
straightly. The setting range is 0 to 4095.
3-6
3.5 Suppressing Main Bang

If main bang appears at the screen center, suppress it as follows.
1. Transmit the radar on a long range and then wait ten minutes.
2. Adjust gain to show a slight amount of noise on the display.
3. Select the 0.25 nm range. Adjust sea clutter control to suppress sea clutter.
4. Press [5] key to choose the MBS on the [ECHO ADJ] menu.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPSSION
0
5. Rotate the wheel to set a suitable value so that the main bang disappears.
The setting range is 0 to 255.
3-7
3.6 Other Settings

ECHO menu setting
Open the ECHO ADJ menu as described on page 3-3 and 3-4.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
To close the menu, press the [MENU] key.
CABLE ATT ADJ

Before adjusting, set the radar as follows:
IR: 2, ES: off, EAV: off, 24nm range, long pulse
(Same as default setting of PICTURE1)
To adjust the cable attenuation manually, choose MANUAL by pressing [2] and the [ENTER]
key, and then rotate the wheel so that noise just appears on the screen when the gain is set
to 80. Default setting is 30 for the antenna cable length of 15m. The setting range is 0 to 73.
To adjust automatically, choose AUTO and press the [ENTER] key. The message “CABLE
ATT ADJ” appears in red at the bottom of the screen. It takes about five minutes to
complete the adjustment, after which the radar goes into stand-by.
DEFAULT ANT HEIGHT

Select height (m) of the radar antenna unit from the sea surface among 5, 7.5, 10, 15, 20,
25, 30, 35, 40, 45 and “more 50 m”.
NEAR STC CURVE, MID STC CURVE AND FAR STC CURVE
Use the default setting. Change the setting if desired according to sea condition.
RING SUPPRESSION
This is mainly used to removes “ring” noise which appears in the waveguide-type radar.
Adjust so the rings disappear at the range of 0.125 nm. The setting range is 0 to 255.
3-8
Scanner setting
1. Open the INITIALIZE menu described on page 3-2.
2. Press [3] key to open the SCANNER menu.
[SCANNER]
1 BACK
2 BLIND SECTOR 1
START 000°
ANGLE 000°
3 BLIND SECTOR 2
START 000°
ANGLE 000°
4 ANT REVOLUTION
LO/HI/AUTO
5 ANT SW
OFF/ON/EXT
6 ANT STOPPED
STBY/TX
7 M SPEC
OFF/ON
Note 1: Set the blind sector as minimum as possible.
8 BB TYPE
Note 2: Do not set the blind sector in the bow direction.
NORMAL/BB
9 [DUAL RADAR]*
*non IMO-type only
To close the menu, press the [MENU] key.
BLIND SECTOR 1 and BLIND SECTOR 2

Set area (up to 2) where no radar pulses will be transmitted, and heading should be
adjusted before setting any blind sector. For example, set the area where an interfering
object at the rear of the scanner would produce a dead sector (area where no echoes
appear) on the display. To enter an area, enter start bearing relative the heading and dead
sector angle. To erase the area, enter 0 for both the START and ANGLE sections. The
setting range of START is 0 to 359° and ANGLE is 0 to 180°.
ANT REVOLUTION
This menu item is used for 42 rpm antenna unit. The default is AUTO, where antenna
revolution speed is high for short range setting and low speed for long range setting. When
LO is selected, the antenna always rotate in 36 rpm, and HI, 42 rpm.
ANT SW and ANT STOPPED

This is used for antenna maintenance by serviceman.
Note: Choose OFF at ANT SW to prevent the antenna rotation. As for ANT STOPPED,
choose STBY to prevent transmission while the antenna is stopped.
M SPEC and BB TYPE

Not used.
DUAL RADAR
See section 3.7.
3-9
INSTALLATION menu setting

Open the INSTALLATION menu by pressing [4] key on the INITIALIZE menu.
[INSTALLATION]
1 BACK
2 RADAR*
*: Cannot be selected.
MAIN/SUB
3 RANGE UNIT ** **: non IMO-type only.
NM/SM/km/kyd
4 RADAR NO*** ***: No.1-4: with antenna unit
1/2/3/4/5/6/7/8 No.5-8: without antenna unit
5 RADAR POSN
FORE/MAIN TOP/
MAIN 2ND/MAIN 3RD/
AFT/PORT/
STAR BOARD
6 MODEL
6/12/25 UP/25 DOWN/
50/30 UP/30 DOWN/60
7 TYPE
IMO/A/B/C/W
8 ON TIME
XXXXXXX.X H
9 TX TIME
XXXXXXX.X H
0 PM GAIN ADJ
0
RADAR
Choose main radar or sub radar.
RANGE UNIT
Choose NM, SM, km or kyd (kilo yard) as appropriate, however-IMO type radar is “NM”
only.
RADAR NO and RADAR POSN

For multiple radar system using the network hub, set number (name) and antenna position
for each system to easily distinguish the radar configuration.
MODEL
Confirm the model of your radar. If the setting of this item is different from your model
(combination of the antenna unit), the radar functions abnormally.
12: for FAR-2117/FAR-2817/ FAR-2117-BB
25UP: for FAR-2127/FAR-2827/ FAR-2127-BB
TYPE
Choose type of radar: IMO, A, B, C, or W.
3-10
TYPE
Choose type of radar: IMO, A, B, C, or W.
ON TIME and TX TIME

These items show number of hours the radar has been turned on and transmitted,
respectively. Value can be changed; for example, after replacing magnetron TX Time can be
reset to 0.
PM GAIN ADJ
Note: If you install the Performance Monitor PM-31 at field, see section 4.4 on page 4-16.
When you choose this item, the radar setting changes as follows.
RANGE: 24 NM
PULSE: LONG
BLIND SECTOR: OFF
STC: OFF by Manual
RAIN: OFF by Manual
ECHO AVERAGE: OFF
VIDEO CONTRAST: 2-B
TUNE: AUTO
1. Adjust the GAIN control so that a slight amount of white noise appears on the screen.
Arcs for performance monitor appear on the screen (Fig.1).
2. Adjust PM GAIN ADJ so that outer arc just disappears (Fig.2). The setting range is 0 to
255.
13.5 - 18.5 nm 13.5 - 18.5 nm
Approx. 0.6 nm
(10 dB)
Fig.1 Fig.2
3-11
OWN SHIP INFO menu setting

Open the OWN SHIP INFO menu by pressing the [5] key on the INITIALIZE menu.
[OWN SHIP INFO]
1 BACK
2 LENGTH/WIDTH
LENGTH 100 m
WIDTH 50 m
3 SCANNER POSN
BOW 0 m
PORT 0 m
4 GPS1 ANT POSN
BOW 0 m
PORT 0 m
5 GPS2 ANT POSN
BOW 0 m
PORT 0 m
6 CONNING POSN
BOW 0 m
PORT 0 m
LENGTH/WIDTH and SCANNER POSN

To inscribe own ship shape on the screen when you choose it on the menu, enter length
and width of the ship and antenna position from the bow and left sides.
The setting ranges are as follows.
LENGTH: 0 to 999 m
WIDTH: 0 to 999 m
BOW: 0 to 999 m
PORT: 0 to 999 m
GPS 1 ANT POSN and GPS 2 ANT POSN

These items are needed for AIS information. Enter the GPS antenna position from the bow
and left sides. The setting ranges are the same as above.
CONNING POSN
Enter the conning position in the wheelhouse, from the bow and left sides. The setting
ranges are the same as above.
When you set the display reference point to the conning position, these values are used to
correct the radar antenna position.
Note: If two or more radars are installed, items other than 3 SCANNER should be the same
on each radar.
3-12
TT PRESET menu setting

Open the TT PRESET menu by pressing [6] key on the INITIALIZE menu.
[TT PRESET] [TRACK PRESET]
1 BACK 1 BACK
2 TT DATA OUTPUT 2 GATE SIZE
[TT PRESET] S/ M /L/LL
OFF/TTM/TTD
1 BACK 3 FILTER RESPONSE
REL/TRUE
2 LAND SIZE 1/ 2 /3/4
4800/9600/
1600 M 4 LOST COUNT
19200/38400
3 ANT SELECT 9 SCAN
3 MAX RANGE
XN12AF/XN20AF/ 5 MAX SPEED
24/32
XN24AF/XN4A/XN5A 100 KTS
4 ECHO LEVEL
SN30AF/SN36AF/ 6 TRACKING MODE
16
SN4A/SN5A 1 /2/3/4
5 QV DISPLAY
4 AUTO ACQ CORRE 7 START TIME TGT VECT
OFF/ON
5 SCAN TIME /SCAN
6 TT W/O GYRO*
5 AUTO ACQ WEED 50 SEC
OFF/ON
1 SCAN 20 SCAN
7 [TT PRESET]
6 [TT DETAIL DATA]
8 [TRACK PRESET]
9 [TT SENSOR DATA]
0 DEFAULT
*: Not on IMO radar
TT DATA OUTPUT
Set the output format from J619 (sentence, bearing and baud rate) of tracked targets.
Sentence: (OFF: No output, TTM: Tracked target information, TTD: Tracked target data)
Bearing: REL: Target bearing from own ship, degree relative,
target course, degree relative.
TRUE: Target bearing, degree true, target course, degree true.
Baud rate: (4800, 9600, 19200 or 38400 bps)
NOTE: The TT DATA OUTPUT port changes according to the setting for INS as described
on page 3-15.
INS-OFF: Output from J619 port only
INS-SERIAL: Output from J619 and J620 (TTM only) ports
INS-LAN: Output from J619 and NETWORK (TTM only) ports
MAX RANGE
Choose the target tracking range, 24 or 32 nm.
ECHO LEVEL
Set the detection level of echoes. The setting range is 1 to 31.
QV DISPLAY
OFF: Normal picture
ON: Quantized picture; always off at power on
3-13
TT W/O GYRO (Not on IMO radar)

If a gyrocompass is not connected, choose the TT function, ON(working) or OFF (no
working).
LAND SIZE
Set the land size in units of 100 m. The setting range is 100 to 3000 m.
ANT SELECT
Set the antenna radiator type of your radar.
AUTO ACQ CORRE

Set the correlation count of automatic acquisition. The setting range is 3 to 10.
AUTO ACQ WEED

Set the cancel count of automatic acquisition. The setting range is 1 to 5.
GATE SIZE
Set the gate size among S, M, L, or LL.
FILTER RESPONSE
Set the filter response function. The setting range is 1 to 4.
LOST COUNT
Set the lost count. The setting range is 1 to 20.
MAX SPEED
Set the maximum tracking speed. The setting range is 40 to 150.
TRACKING MODE
Set the tracking mode among 1 to 4.
START TIME TGT VECT

Choose time which a vector appears after acquisition, TIME or SCAN and set seconds or
scan counts.
3-14
OTHER menu setting

Open the OTHER menu by pressing [8] key on the INITIALIZE menu.
[OTHERS]
1 BACK
2 DEMO ECHO
OFF/EG/TT-TEST/PC
3 EAV W/O GYRO
OFF/ON
4 TT CATEGORY SELECT
CAT1/CAT2 3
5 INS
OFF/SERIAL/LAN
EAV w/o GYRO

If a gyrocompass is not connected, choose the echo average function, ON (working) or OFF
(no working).
TT CATEGORY SELECT
Choose CAT1 or CAT2•3 depending on your ship’s size.
CAT1: All ships over than 10,000 GT
CAT2: All ships between 500 and 10,000 GT
CAT3: All ships less than 500 GT
INS
Choose appropriate item according to the ECDIS connected.
OFF: No connection
SERIAL: When connecting FEA-2105 series ECDIS.
LAN: When connecting FEA-2107 series ECDIS.
3-15
3.7 Dual Radar Display (non IMO-type only)

The image from two or more radars may be shown together on one radar display. This
allows you to take advantage of the best characteristics radars has to offer.
Image from main radar
Image from
external radar
Separate internal and external

images ("COMBINE" setting)
The following should be done in order to enable the dual radar display:
• Set antenna position correctly on both the main radar and the external radar.
• Select external radar to use, from the DUAL RADAR menu. (See paragraph
3.7.3.)
3.7.1 Enabling/Disabling the Dual Radar Display

Enable or disable the dual radar display as shown in this section.
Note 1: The Tx blanking sector boundary lines are not shown when the dual radar display is
active. Further, neither the internal or external image is shown in the Tx blanking
sector.
Tx blanking sector is not shown.
Tx blanking sector No image in Tx blanking sector.
Display area
Tx blanking sector Dual radar display with

Tx blanking sector
3-16
Note 2: In the dual radar display, a guard zone set on the main radar is also accommodated on
the external radar. When the position of the antennas for the main and external radars
is different and the No. 2 guard zone is set on a close-in range, the on-screen guard
zone may be shifted slightly from both the main radar antenna reference and external
radar antenna reference. Accordingly, on the dual radar display, the actual guard zone
area may be shifted slightly. For example, the guard alarm sounds against a target
which has almost entered the guard zone. The further the range the smaller the shift;
however, there is little shift with the No.1 guard zone (3-6 mile range, fixed). Further, do
not set a guard zone such that it straddles a boundary line of the dual radar sector.
A guard zone cannot be set while the dual radar display is active. Set a zone before activating
the dual radar display.
1. Open the INITIALIZE menu. See page 3-4.

2. Press the [3] key to show the SCANNER menu.
3. Select 9 [DUAL RADAR] and push the left button.
[DUAL RADAR]
1 BACK
2 DUAL RADAR
OFF/ COMBINE
3 COMBINE MODE
OWN/EXT
4 COMBINE SECTOR
START 000°
ANGLE 000°
5 COMBINE RANGE
START 00.00NM
LENGTH 00.00NM
6 EXT RADAR
1/2/3/4

5. Select OFF or COMBINE as appropriate and push the left button. For COMBINE, the
ANTENNA box at the top left-hand side becomes gray.
OFF: Turn off the dual radar display.
COMBINE: Display a part of the external radar image in the window on the main radar.
3-17
Push the right button four times to close the menu.

Note 1: The dual radar function becomes inoperative when the external radar is turned off, set
to stand-by, or set as sub display. When this happens, the buzzer sounds and the
message "EXT RADAR STBY" (power off, stand-by only) appears.
Note 2: The dual radar display is inoperative on the stern-up and shuttle ferry modes.
Note 3: Some functions of the external radar image, listed below, may be adjusted from the
main radar.
1) Left-click the radar selection indication "CTRL OWN" at the top-left side of the screen to
switch control to the external radar. The indication then shows "CTRL EXT". Each click of
the indication switches control between the main and external radar alternately.
2) The external image may be adjusted from the main radar. The following functions may be
adjusted:
• Transmit/stand-by switching
• PICTURE box setting
• GAIN
• A/C SEA
• A/C RAIN
• Tuning
• ECHO menu setting (2nd trace echo rejector, performance monitor)
• Range scale
• TT functions.
• CPA/TCPA box settings
3-18
3.7.2 Specifying Sector Width and Length

When 2 DUAL RADAR in the DUAL RADAR menu is set for "COMBINE", specify
the width and length of the sector from the external radar to display on own radar.
1. Open the INITIALIZE menu.

4. Select 3 COMBINE MODE and push the left button.
5. Select OWN or EXT and push the left button.
OWN: Set own radar’s antenna as reference point and set display area of own
radar. The area outside that set here is where the image from the
external radar will be displayed.
EXT: Set external radar’s antenna as reference point and set display area of
external radar. The area outside that set here is where the image from
own radar will be displayed.
Radar selected for COMBINE: External Radar selected for COMBINE: Own
START: 315 degrees START: 45 degrees
ANGLE: 90 degrees ANGLE: 270 degrees
START: 00.00 nm START: 00.00 nm
LENGTH: 99.99 nm LENGTH: 99.99 nm
Picture from
external radar
Position of antenna
for external radar
Position of antenna
for own radar
Picture from
own radar
6. Select 4 COMBINE SECTOR and push the left button.
3-19
7. Use the scrollwheel to set START and ANGLE, referring to the description and
example below. Spin the scrollwheel to set and push it to confirm.
A solid green line marks the dual radar display area.
• START: Start point of the sector (in degrees, 000-359)
• ANGLE: Width of the sector (in degrees, 000-359)
In the example below, START is 130° and ANGLE is 100°.
Width of sector
START
ANGLE (Example: 130°)
(Example: 100°)
8. Select 5 COMBINE RANGE and push the left button.

9. Use the scrollwheel to set START and LENGTH, referring to the example below.
Spin the scrollwheel to set and push it to confirm.
• START: Set range start point.
• LENGTH: Set length of sector.
START
LENGTH
Example:
START: 01.00 nm
LENGTH: 02.00 nm
Push the right button four times to close the menu.
3-20
3.7.3 Choosing External Radar (image source)

Select the external radar to use in the dual radar display.
1. Open the INITIALIZE menu.

[DUAL RADAR]
1 BACK
2 DUAL RADAR
OFF/ COMBINE
3 COMBINE MODE
OWN/EXT
4 COMBINE SECTOR
START 000°
ANGLE 000°
5 COMBINE RANGE
START 00.00NM
LENGTH 00.00NM
6 EXT RADAR
1/2/3/4
4. Select 6 EXT RADAR and push the left button.

5. Select desired radar no. and push the left button.
Only the numbers of connected radars are valid. Radar no. is set on the Installation Setting
menu.
6. Press the [MENU] key to close the menu.
3-21
3-22
4. INSTALLING OPTIONAL
EQUIPMENT
4.1 Gyro Converter GC-10
The Gyro Converter GC-10, incorporated inside the processor unit, converts analog
gyrocompass reading into digital coded bearing data for display on the radar screen.
This section explains how to install the GC-10 (mainly consisting of the GYRO
CONVERTER board) and set it up according to gyrocompass connected.
Installing the GYRO CONVERTER board

Necessary Parts: GC-10-2 (Code number 000-080-440)
See packing list for details at the back of this manual.
1. Open the processor unit.

4
3
12
3
1
7
3
1
1
1
5
1
1
1
12
Processor unit (Opened)
4-1
4. INSTALLING OPTIONAL EQUIPMENT
2. Fasten the GYRO CONVERTER board in the processor unit with five washer head
screws and male connector 231-607/019-FUR (called J602) with two screws.
Screw
GYRO CONVERTER board
M3x8 5 pcs
64P1106A
Screw
M2.6x10 2 pcs
Connector (231)
231-107/026-FUR
1
7
Connector (231)
231-607/019-FUR
Attaching GYRO CONVERTER board in the processor unit
3. Connect the GYRO CONVERTER board and the 03P9342 board with connector
assemblies 03-2088 and 03-2091.
4-2
4. Connect the GYRO CONVERTER board and J602 with two connector assemblies
03-2089 and 03-2090.
Wiring for WAGO connector
Press downward.
Terminal opener
2 Connection for J602
J602 1 Connection for P608
PPL P608
7 6 5 4 3 2 1
From J4 BLU YEL
1 2 3 4
GRN ORG
YEL
ORG RED
BRN
From J5 RED
BRN
WAGO connector
Twist
Wire
Procedures
1. Twist the cores
2. Press the terminal opener downward.
2 VH connector assy. 3. Insert the wire to hole. 1 NH connector assy.
03-2089 (5P) 4. Remove the terminal opener.
03-2091 (5P)
5. Pull the wire to confirm that it is
secure.
2 VH connector assy.
To J602 XH-PH connector assy.
03-2090 (3P)
03-2088 (6-14P)
P5 To P608
P4 P7
P1
P603
J5 GYRO CONVERTER J1
4
J4 64P1106A
1
P608
3
12
J7
1
J602
7
1
1
J603
5
1
1
1
12
TB
03P9342
1
Connecting connector assemblies
4-3
5. Confirm gyrocompass specifications and set up the DIP switches and jumper wires on
the GYRO CONVERTER board according to gyrocompass connected:
x Setting jumper wires and DIP switches by gyrocompass specifications: page 4-5
x Setting jumper wires and DIP switches by make and model of gyrocompass: page 4-7
x Location of jumper wires and DIP switches: page 4-8
6. Pass gyrocompass cable through the cable clamp and connect it to connector J602 as
shown in the figure on page 4-3.
7. Attach the clamps on the plastic cover and then attach the cover to the GYRO
CONVERTER board as shown in the figure below. Insert cables to the clamp ED-1,
respectively.
Screw
Plastic cover M4x8 3 pcs
Clamp CKS-10-L
Clamp EDS-1
Insert cables to these

Clamp CKS-13-L
clamp.
4
3
12
3
1
1
1
1
1
1
1
12
Attaching plastic cover for GYRO CONVERTER board
8. Close the processor unit.
4-4
Connection of external power supply

An external power supply is necessary when the repeater signal is step-by-step type and
the step voltage is below 20 V or output voltage is less than 5 W.
1. Cut jumper wire JP1 on the GYRO CONVERTER board when an external power supply
is used.
2. Connect gyro cable and power cable as shown below.
[A] 64P1106
External Power Supply J5

20 - 135 VAC 1 > R2
20 - 100 VDC 2 > R1/COM
Either connection
in case of DC
polarity.
J4
S1
1 > S1
Gyrocompass S2 2 > S2
(Step type) S3 3 > S3
COM
4>T
F.G. 5 > F.G.
Connection of external power supply to GYRO CONVERTER board
DIP switch, jumper wire settings

Default setting
The gyro converter GC-10 is set at the factory for connection with the gyrocompass
specifications below.
AC synchronous signal: 50/60 Hz

Rotor voltage: 60 V to 135 V AC
Stator voltage: 60 V to 135 V AC
Gear ratio: 360x
Supply voltage: 30 V to 135 V AC
If the specifications of the gyrocompass differ from those mentioned above, change jumper
wire and DIP switch settings on the GYRO CONVERTER board. Settings may be changed
according to gyrocompass specifications (see page 4-6) or make and model of
gyrocompass (see page 4-7). For the location of DIP switches and jumper wires, see page
4-8.
Note: If you change the setting with power supplied, set #8 of SW2 from OFF to ON, then
OFF again.
4-5
Setting method 1: DIP switch settings and gyrocompass specifications

1) Gyrocompass type 2) Frequency
Gyrocompass SW SW SW SW SW
type 1-4 1-5 1-6 JP1 Frequency 1-7 1-8 Remarks
AC #1, #2, AC synchronous

synchronous OFF OFF OFF #3 50/60 Hz OFF OFF pulsating current
DC #2, #3, AC synchronous
synchronous OFF OFF OFF #4 400 Hz ON OFF pulsating current
#4, #5, AC synchronous
DC step ON OFF OFF #6 500 Hz OFF ON pulsating current
Full-wave #4, #5, DC synchronous
pulsating current OFF ON OFF #6 DC ON ON DC step
Half-wave #4, #5,
ON ON OFF
pulsating current #6
3) Rotor Voltage (between R1 & R2) 4) Stator Voltage (between S1 & S2)
SW Stator SW SW
Rotor Voltage JP3 JP2
2-1 Voltage 2-2 2-3
20 to 45 VAC, or
20 to 45 VAC ON #2 ON OFF #2
20 to 60 VDC
30 to 70 VAC, or
30 to 70 VAC OFF #2 OFF OFF #2
40 to 100 VDC
40 to 90 VAC ON #1 40 to 90 VAC ON OFF #1
60 to 135 VAC OFF #1 60 to 135 VAC OFF OFF #1
5) Ratio 6) Supply Voltage

SW SW SW Stator
Ratio 1-1 1-2 1-3 Voltage JP4 JP5
360X OFF OFF OFF 20 to 45 VAC, or 20 to 60 VDC #2 #2

180X ON OFF OFF 30 to 70 VAC, or 40 to 100 VDC #1 #1
90X OFF ON OFF
36X ON ON OFF
7) AD-10 format data 8) NMEA-0183

Tx interval Tx interval and Output sentence
Select data transmitting interval for ports 1 to 6 with jumper Tx SW SW Output
wires JP6 and JP7: #25 for 25 ms, #200 for 200 ms. interval 2-5 2-6 sentence
Note: The Tx interval is available in 25 msec or 200 msec. 1s OFF OFF HDT+VHW
Use 25 msec for radar. 200 ms ON OFF HDT
100 ms OFF ON HDT
25 ms ON ON HDT
9) NMEA-0183 10) NMEA-0183 11) Power fail 12) Stator signal
Version no. Baud rate detection breaking detection
Version no. SW3-1 Baud rate SW3-2 Talker SW3-3 Detection SW2-7
1.5 OFF 4860bps OFF Disable OFF Execute OFF
2.0 ON 38400bps ON Enable ON No execute ON
(Use OFF for radar.) SW2-4: factory use only
SW3-4: not used
4-6
Setting method 2: by make and model of gyrocompass
Maker Models Specification SW SW SW SW SW SW SW SW SW SW SW JP 1 JP 2 JP 3 JP 4 JP 5

1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 2-1 2-2 2-3
Anschutz Standard 2,3 AC synchronous OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF #1, #2 #2 #1
1 #
50/60Hz #2,#3
Rotor voltage: 50/60V
Stator voltage: 22V
360x
Standard 4,6 AC synchronous OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #2 #1 #1
1 #
50/60Hz #2,#3
Stator voltage: 90V
360x
Standard 20 DC step ON OFF OFF ON OFF OFF ON ON - ON OFF #4, #2 - #2
2 #
35V 180x #5,#6
COM(-) ,3-wire(+)
Yokogawa C-1/1A/2/3 AC synchronous OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF #1, #2 #2 #1
1 #
Navtec A-55, B-55 50/60Hz #2,#3
(Pla th Rotor voltage: 50/60V
type) Stator voltage: 22V
360x
CMZ-700 DC step ON OFF OFF ON OFF OFF ON ON - ON OFF Remo- #2 -
24V 180x
COM(+), 3-wire(-)
ve * *
C MZ-250X/ DC synchronous 360x OFF OFF OFF OFF OFF OFF ON ON - ON OFF Remo- #2 -
300X/500 ve * *
DC step ON OFF OFF ON OFF OFF ON ON - ON OFF #4, #2 - #2 #2
35V 180x #5,#6
COM(+),3-wire(-)
CMZ-100/200/ AC synchronous OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #1 #1 #1 #1
300 50/60Hz #2,#3
C-1Jr,D-1Z/1/3 Rotor voltage: 100V
IPS-2/3 Stator voltage: 90V
360x
CMZ-50 step ON OFF OFF ON OFF OFF ON ON - ON OFF Remo- #2 -
35V 180x
See note below. COM(+),3-wire(-)
ve * *
Plath NAVGAT II/III AC synchronous OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #2 #2 #1 #1
50/60Hz #2,#3
Stator voltage: 68V
360x
Tokimec ES-1/2/11 AC synchronous ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #1 #1 #1 #1
(Sperry GLT-101/102/ 50/60Hz #2,#3
type) 103/106K/107 Rotor voltage: 100/110V
Stator voltage: 90V
36x
ES-11A/110 AC synchronous OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #1 #1 #1 #1
TG-200 50/60Hz #2,#3
PR222R/2000 Rotor voltage: 100/110V
PR237L/H Stator voltage: 22V
GM 21 90x
MK-14 DC step ON OFF OFF ON OFF OFF ON ON - OFF OFF #4, #2 - #1 #1
MOD-1/2/T 70V 180x #5,#6
NK-EN,NK-EI COM(-), 3-wire(+)
SR-130/140 DC step ON OFF OFF OFF ON OFF OFF OFF - OFF OFF #4, #2 - #1 #1
70V 180x #5,#6
5-wire, open collector
TG-100/5000 DC step ON OFF OFF ON OFF OFF ON ON - OFF OFF #4, #2 - #1 #1
PR-357/130/ 70V 180x #5,#6
140, ES-17 COM(+), 3-wire(-)
GLT-201/202
/203
TG-6000 DC step ON OFF OFF ON OFF OFF ON ON - ON OFF #4, #2 - #2 #2
24V 180x #5,#6
GM-11 AC synchronous OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #1 #1 #1 #1
50/60Hz #2,#3
Rotor voltage: 100V
Stator voltage: 90V
90x
SR-120,ES-16 DC step ON OFF OFF ON OFF OFF ON ON - ON OFF #4, #2 - #2 #2
MK-10/20/30 35V 180x #5,#6
Kawasaki GX-81 AC synchronous OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF #1, #1 #1 #1 #1
50/60Hz #2,#3
Stator voltage: 90V
90x
Armabrown MK-10,MKL-1 DC step ON OFF OFF ON OFF OFF ON ON - OFF OFF #4, #2 - #1 #1
SERIES1351, 50V 180x #5,#6
MOD-4 COM(+), 3-wire(-)
Robertson SKR-80 DC step ON OFF OFF ON OFF OFF ON ON - ON OFF #4, #2 - #2 #2
35V 180x #5,#6
COM(-), 3-wire(+)
*: Set JP4 and JP5 according to the voltage of the external power supply.
Note: If CMZ-50 has 35VDC, set JP1 to #4, #5, #6.
4-7
Location of DIP switches, jumper wires on the GYRO CONVERTER board
JP5, JP4
(Supply voltage)
JP2
(Stator voltage)
JP3
(Rotor voltage)
SW3
DIP switch
JP1 64P1106 J12
(Gyro type) (Data output
port #6)
J11
(Data output
port #5)
J10
(Data output
port #4)
SW2
DIP switch
JP6, JP7
(AD format
Fuse SW1 data Tx interval)
(2A) J4 J9
DIP switch
(Stator signal input) (Data output port #3)
J5 J6 J8
(Rotor signal input, (IEC-61162-1 output port) (Data output port #2)
external power input) J7
(Data output port #1)
Setting the heading readout on the radar display

Confirm that the gyrocompass is giving a reliable readout. Then, set the heading readout on
the radar display with the gyrocompass readout as follows:
1. Roll the trackball to place the arrow in the HDG box at the top right corner of the screen.
2. Push the right button on the trackball module to open the HDG menu.
[HDG MENU]
1 HDG SOURCE
AD-10/SERIAL
2 GC-10 SETTING
000.0˚
HDG menu
3. Press the [1] key to choose the HDG SOURCE and choose AD-10.
4. Press the [2] key to choose the GC-10 SETTING option.
5. Roll the wheel to set gyrocompass reading.
6. Press the [MENU] key to close the menu.
4-8
4.2 Memory Card Interface Unit

x Locate the memory card interface unit away from heat sources because of heat that can
build up inside the cabinet.
x Locate the unit away from places subject to water splash and rain.
x Leave sufficient space at the sides and rear of the unit to facilitate maintenance.
x A magnetic compass will be affected if the unit is placed too close to the magnetic
magnetic compass.
Flush mounting
This unit can be flush-mounted in a panel with the standard installation materials.
1. Prepare a cutout in the mounting location, referring to the outline drawing at the end of
this manual.
2. Screw in the threaded rods to the flange of the front panel of the unit securely by hands.
3. Set the unit to the cutout.
4. Insert the flat washer, spring washer and nut in that order for each rod and fasten the
nuts.
Flush mounting
4-9
Desktop mount
For desktop mount, the optional desktop mount kit FP03-10201 is required. Refer to the end
of this manual.
1. Fix the mounting bracket 19-023-3081 on the unit with four screws.
2. Mount the above assembly on a desktop with four tapping screws.
Console mount
For console mount, the optional console mount kit FP03-10202 is required. Refer to the end
of this manual.
1. Fix the mounting bracket 19-023-3091 on the unit with four screws.
2. Mount the above assembly to the console with four sets of nut, spring washer and flat
washer.
Connection
1) Connection between one processor unit and one memory card IF unit
Connect as shown in the figure below.
12 VDC
Memory card IF unit
Processor unit MJ-A3SPF0015-100 (10 m)
J614 12 VDC
two mini-cards
PSE-4PTX-BL (10 m)
NETWORK NETWORK
RJ-45
2) Connection between one memory card IF unit and multiple processor units
Prepare optional LAN cable kit and switching hub HUB-100. Connect as shown in the next
page. Set the radar number on the INSTALLATION menu (see page 3-10), and then turn the
power off and on.
LAN cable kit

Type Code No. Contents
OP03-28900 000-082-658 Cable FR-FTPC-CY (10 m), Modular connector 2 pcs.
4-10
Memory card IF unit

No.1 MJ-A3SPF0015-100 (10 m)
J614 12 VDC
Processor two mini-cards
unit FR-FTPC-CY (10/20/30 m)
(straight) NETWORK
NETWORK
FR-FTPC-CY (10/20/30 m)
(straight)
Switching hub
FR-FTPC-CY
No.2 (10/20/30 m)
Processor (straight)
unit
HUB-100
No.3 (option)
Processor
unit FR-FTPC-CY (10/20/30 m) (straight)
No.4 FR-FTPC-CY (10/20/30 m) (straight)

Processor
unit
Note: When two memory card interface units are connected via network, change ID code
for the second unit.
1. Remove the cover and set IP0 bit of the DIP switch S1 to ON on the CARDCPU board
03P9333.
2. Set INIT bit of S1 to ON and turn on the power of the radar. Wait till CR2 starts blinking.
Never turn off the power until CR2 starts blinking.
3. Turn off the power and set INIT bit to OFF.
ON OFF
J314 IP0
IP1
IP2
INIT
S1
CR2
(Default: all OFF)
CARDCPU board 03P9333
4-11
4.3 DVI-RGB Conversion Kit (for VDR connection)

This information provides the procedure necessary for the installation of the DVI-RGB
conversion kit. This kit is installed in the processor unit to enable connection of a VDR
(Voyage Data Recorder) or RGB monitor to record radar pictures into a VDR. When
changing the D-sub 15P of the RGB cable to the BNC connector, use the BNC connector
converter described on page 4-17. This RGB output complies with the image test defined in
the VDR test standard, IEC 61996.
Name: DVI-RGB conversion kit

Type: OP03-180-2
Code no.: 008-536-070
Resolution: Outputs RGB with the resolution of DVI input.
Display unit Resolution DIP switch setting (S-1#1)
MU-201CR 1024x1280 OFF
MU-231CR 1024x1365 ON
Output signal specification: Video; 0.7Vp-p, 75Ω termination, positive polarity
Horizontal sync signal; TTL level, negative polarity
Vertical sync signal; TTL level, negative polarity
See packing list for contents. Refer to the figure below for modification.
DVI-RGB Conversion board
M3x8 (SLB-FRN4-A)
6 pcs DVI video input
DVI cable
J9 J3
(10 pin)
J4
(6 pin)
J615
03-2094
03-2092 03P9342 board
03-2093 RGB-BUFF board*

(03P9229B) D-sub 15P
SQ-35 M3x8 Female
Spacer J2
4 pcs J3
6 pcs J1 (3 pin)
(13 pin)
RGB Cable
(User supply)
Spring washer
Fixing
holes
Boss
Ferrite core
RGB video output Clamp copper tape
section by cable clamp.
To external RGB monitor or
BNC connector converter
for VDR connection (see
page 4-17).
Ferrite core side: Connect to DVI-D port on
the upper part of the processor unit.
*Indepent of the MAIN board.
4-12
1. Remove the top cover and open the upper part of the processor unit.
DVI-D port
(Connect DVI cable at step 13)

Processor unit
2. Fix the 03P9229B board (RGB-BUFF) with four screws. (See the figure below.)
3. Attach the connector assemblies to J1 and J3 on the 03P9229B board as follows.
J1㧦13-pin connector of the connector assembly 03-2094
J3㧦3-pin connector of the connector assembly 03-2093
4. Attach six sets of spring washers and spacers to the positions shown below.
Spring washer, spacer 03P9229B board
J2 (Connect RGB Cable at step 11.)
J3
J1 J2
03P9342 board
J615 (Connect connector assemblies at step 9.)
Processor unit (Lower part)

5. Attach the DVI-RGB conversion board to the location shown in the figure on the next
page.
4-13
DVI-RGB
Conversion board
J9 J3 (Connect DVI cable at step 10.)
J4
Fixing the DVI-RGB conversion board

6. Attach the 10-pin connector from J1 on the 03P9229B board to J9 on the DVI-RGB
board.
7. Attach the connector assembly 03-2092 to J4 on the DVI-RGB conversion board.
8. Remove connector housing J615 from the 03P9342 board. Connect the cable from J3
on the 03P9229B board and the cable from J4 on the DVI-RGB conversion board to
J615. After connection, attach J615 to the 03P9342 board.
To connect wires to the connector housing, use the terminal opener (supplied as installation
materials) as shown below.
Terminal opener
J615 Housing
1 Press downward
1
2
BRN 3
4
RED
ORG 5
YEL
2 Insert core
GRN
Connecting wires to the housing

9. Connect the DVI cable to J3 on the DVI-RGB conversion board. Connect the end which
does not have the ferrite core.
10. Pass an RGB cable (local supply) through the cable clamp and connect it to J2 on the
03P9229B board.
11. Pass the DVI cable through the cable clamp, laying the section with copper tape in the
cable clamp.
12. Assemble the processor unit and connect the other end of the DVI cable to DVI-D port.
4-14
4.4 Performance Monitor PM-31

This kit is installed in the antenna unit of the FAR-2107/2807 series X-band radar to monitor
radar performance.
Name: Performance monitor

Type: PM-31
Code no.: 008-080-438
Name Type Code number Qty

Ԙ SCANNER COVER ASSY. PM-31 008-539-430 1
ԙ GREASE GASKET GREASE #2 000-149-704 1
50G
Ԛ SM-XH CONNECTOR 03-2108㧔6P-6P) 008-534-840 1
ASSY.
ԛ LIFTING FIXTURE 03-001-3264 300-132-640 1
Ԝ GASKET 03-001-3263 300-132-631 1
Procedure
To hoist the scanner cover assy. to the radar mast, by using rope, attach the lifting fixture ԛ to
the scanner cover assy.Ԙ.
1. Remove the bolt and chain at the bottom of the stern-side cover, and then remove the
cover.
2. Coat the bolt hole on the scanner cover assy.Ԙ with silicone sealant (Adhesive 1211)
and secure the chain with the bolt.
3. Remove the cover at the bow side also.
4. Insert the XH connector of the SM-XH connector Ԛ assy. to J911 on TB board 03P9349
and the SM connector of the SM-XH connector assy. to the relay plate.
5. Coat the gasket Ԝ with the gasket grease #2 50G ԙ and attach it to the scanner cover
assy.Ԙ.
6. Connect the cable assembly coming from the scanner cover assy.Ԙ to the SM connector
attached at step 4 above.
7. Attach the scanner cover assy. to the stern side of the antenna unit.
8. Reattach the bow-side cover.
4-15
View B
How to fix lifting fixture
P922
Relay plate 1.Insert the lifting fixture
as shown below.
Stern side
Lifting fixture
Fix the cable.
Scanner cover assy 2. Fix the lifting fixture

as shown below.
Upside down the fixture

from step 1 and pull it
in arrow mark direction.
Note:Fix flat side of the fixture to

the coating face.
Lifting fixture Lifting fixture

Coating face
A
* TB board
Gasket
Scanner cover assy

TB board 03P9349
Change the chain here.

J911 is on rear side.
Bow side
4-16
4.5 BNC Connector Converter

To connect the VR-5000 (FURUNO Voyage Data Recorder) to this radar, the DVI-RGB
conversion kit (mentioned at previous paragraph) and the BNC connector converter are
required. Also VGA cable (between the processor unit and the BNC connector converter)
and five 75 ohms coaxial cables (between the BNC connector converter and VR-5000) are
required.
FAR-2107 VR-5000
Processor Unit VD1 Data collecting unit
BNC connector 75 W coax. cable
converter R R
DSUB-BNC-1 G G
B B
VGA cable H HS
DVI-RGB D-sub 15P D-sub 15P
Conversion kit Female V VS
Male
Interconnection
4-17
4.6 Junction Box

If the length of the antenna cable is more than 100 m, the optional junction boxes are
required. These boxes should be mounted at the location protected because its
waterproofing is IPX3.
Antenna unit Processor unit
RW-9600 RW-9600
(Max 15 m) (Max 15 m)
DPYCY-6 (3 pcs.)
Junction box TTYCY-4 (1 pc.) Junction box
RJB-001 RG-12/UY (1 pc.) (Max 270 m) RJB-001
Shipyard supply
Mounting
Fasten the junction boxes to the mounting location with four sets of M8 bolt and nut.
514
474
NAMEPLATE
320
280
270
60 FIXING HOLES
4-I10
139
Mass: 12kg
360
430
4-18
Cable fabrication
RW-9600
5
20 approx. 450 Units: mm
Armor Shield
Pull out inner cables from here.
Vinyl sheath
14 5 9
Shield
Coaxial cable
Crimp on lug for M8
DPYC-6 and TTYC-4
DPYC-6: approx. 130 DPYCY-6 TTYCY-4 (Four twisted pairs)

TTYCY-4: approx. 150
20 I = 13.9 mm I = 17.7 mm
Sheath
5 Armor
6 Armor
Sheath
Sheath
Armor Taper for unused wires.

Conductor Conductor
Vinyl sheath S = 6 mm 2 S = 0.75 mm 2
I= 3.12 mm I = 1.11 mm
RG-12/UY
20 60 14 5 9
Inner conductor
Vinyl sheath Armor Outer conductor
4-19
Connection
Insert each cable to the cable gland as follows.
Cable gland
Flat washer
Vinyl sheath
Gasket
Clamping gland
Cut and trim armor.
Connect each cable cores to the terminal board, referring to the interconnection diagram on
next page.
Clamp outer conductor of coaxial cables. Fix wires with cable-tie.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
RG12/UY
RG-12/UY TTYCY-4 DPYCY-6 RW-9600

Connect inner conductors. M8 screw for grounding
4-20
Antenna unit Junction box Junction box Processor unit
03P9342
03P9349 RW-9600
DPYCY-6 RW-9600 J613
TB801 BRN
TX-HV 1 BRN 1 1 1 TX-HV
N.C. 2 2 2 2 N.C.
RED[B] 3 J610
3 DPYCY-6 ORG[B]
ORG[B] 1 24V_PLUS
24V_PLUS 3 4 4 YEL[B]
24V_MINUS 4 YEL[B] 5 2 24V_MINUS
5
BLU[B] DPYCY-6 BLU[B] 3 MOTOR(+)
MOTOR(+) 5 6 6
GLY[B] GLY[B]
MOTOR(+) 6 4 MOTOR(+)
PPL[B] PPL[B] 5 MOTOR(-)
MOTOR(-) 7 7 7 WHT[B]
WHT[B]
MOTOR(-) 8 6 MOTOR(-)
8 N.C. 8 N.C.
9 N.C. TTYCY-4 9 N.C. RED 7
SPU_RF_D_A 9 RED 10 10 SPU_RF_D_A
pair GRN
SPU_RF_D_B 10 GRN 11 11 8 SPU_RF_D_B
BRK BRK 9
RF_SPU_D_A 11 12 pair
12 RF_SPU_D_A
WHT WHT 10
RF_SPU_D_B 12 13 13 RF_SPU_D_B
GRN[B] GRN[B]
SIG-GND 13 14 14 11 SIG-GND
15 N.C. RED[B]
GND 14 15 N.C. 12 GND
J609
TB802
COAX COAX 1 IF_VIDEO
IF_VIDEO 1 1 1
GND 2 2 RG-12/UY 2 2 GND
IV-1.25
Clamp with cable-clamp
4-21
4-22
5. INPUT/OUTPUT DATA
Input and output data are shown in the table below.
Note: This radar accepts position data fixed by WGS-84 geodetic datum only. Set the
datum to WGS-84 on the EPFS (GPS, etc.) connected to this radar. If other type of datum is
input, the error message "DATUM" appears and the AIS feature is inoperative. Baud rate for
the serial input is automatically set to 4800, 9600, 19200 or 38400 as appropriate.
Input
Data Specifications Contents Remarks
Heading signal synchro or step GC-10 required AD-10 and
IEC 61162 are switched by
AD-10 format External AD-100 menu setting.
IEC 61162-2**
Speed signal IEC 61162-1
Navaid data IEC 61162-1 Position, course, For IMO spec, IEC-61162-1
speed, waypoint, Edition 2 is required.
route, time, wind data,
current data, depth,
temperature, roll, pitch
External radar Heading, No STC control Operate as remote display
signal Bearing, Trigger,
Video
Alarm ACK input Contact closure Input from alarm system
IEC61162-1 ACK Input from alarm system
Track Control unit RS-422 Option
Output
Radar system data RS-232C RSD, OSD, TLL, For PC plotter
TT data* IEC 61162-1 TTD, TTM, TLB For ECDIS
ALARM data IEC 61162-1 ALR For ALARM system
Remote display HD, BP Trigger, 2 ports
signal Video
External LCD DVI Same as main display 2 systems in total
monitor signal unit
External CRT R, G, B, H, V Same as main display Option
monitor signal unit
Alarm signal Contact closure Output to alarm system 4 systems, Output contents
by using photo-relay are selected by menu.
*The output sentence, mode and baud rate can be set at the TT Preset menu.
**Data cycle should be input with more than 40 Hz (HSC) or 20 Hz (normal speed).
5-1
5. INPUT/OUTPUT DATA
IEC 61162 input sentence and priority

Contents Sentence and priority
Speed (STW) VBW>VHW
Speed (SOG) VBW
Speed (position) VTG>RMC
Heading (True) THS*>HDT*
Position GNS>GGA>RMC>GLL
Datum DTM
Waypoint BWR, BWC, RMB
Route WPL, RTE
Date, Time ZDA
Depth DPT >DBT>DBS>DBK
Temperature MTW
Wind MWV>VWT>VWR
Set and Drift VDR
ALARM ACK ACK
*: THS and HDT are IEC61162-2
Others: IEC61162-1 ed2.
IEC 61162 output sentence
Contents Sentence
Target L/L TLL *
Radar system data RSD
Own ship data OSD
TT target data TTD, TLB, TTM
ALARM data ALR
*non IMO-type only.
5-2
A-1 A-2
%1&'01 ).: %1&'01 ).:

6;2' %2 6;2' %2
Ꮏ੐᧚ᢱ⴫ Ꮏ੐᧚ᢱ⴫
+056#..#6+10/#6'4+#.5 +056#..#6+10/#6'4+#.5
⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂ ↪ㅜ㧛஻⠨ ⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂ ↪ㅜ㧛஻⠨
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
㒐ⲁࠧࡓ 㩔㩨㩒ᐳ㊄
41*5 /575
%14415+102411(47$$'4 524+0)9#5*'4
%1&'01 %1&'01

㩆㨺㩣㩦㨹㩆㨶㨺 ౐ⷺ㩘㩨㩣㩎
41*5 /:575
5'#.9#5*'4 *':#)10#.*'#&$1.6
%1&'01 %1&'01

ᠲ૞㩤㩔㩨㨺㩃㨺㩖㩨㩣⚵ຠ 49
49
6'4/+0#.12'0'4 %#$.'#55;
%1&'01 %1&'01

࿶⌕┵ሶ
(8
.(
%4+/210.7)
%1&'01

౐ⷺ㩏㨹㩎㩆㨷
/575
*':#)10#.076
%1&'01

㩚㩀㩨㩁㩙㩣ᐔᐳ㊄
/575
(.#69#5*'4
%1&'01

㩔㩨㩒ᐳ㊄
/575
524+0)9#5*'4
%1&'01

౐ⷺ㩘㩨㩣㩎ో㩒㩆㩨
/:575
*':#)10*'#&5%4'9
%1&'01

/575
*':#)10#.076
%1&'01

㩚㩀㩨㩁ᐔᐳ㊄
/575
(.#69#5*'4
%1&'01

ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬ ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/' 37#.+6;+56*'5#/'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).:

A-3 A-4
%1&'01 (5: %1&'01 (5:

6;2' %2 6;2' %2
Ꮏ੐᧚ᢱ⴫ Ꮏ੐᧚ᢱ⴫
+056#..#6+10/#6'4+#.5 +056#..#6+10/#6'4+#.5
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
1㩢㩧㩂㩨㩕㩩㩧
,$2 41*5
14+0) 2+0
%1&'01 %1&'01

ࡃࡀᐳ㊄ 1㩢㩧㩂㩨
/575 ,$2
524+0)9#5*'4 14+0)
%1&'01 %1&'01

㩚㩀㩨㩁ਣᐔᐳ㊄ ౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
/575 /:575
(.#69#5*'4 *':*'#&5.16$1.6$
%1&'01 9#5*'4 %1&'01

౐ⷺ㩇㩢㩦㩢㩘㩨㩣㩎㩃㩚㩆㨺㩣
/:575 59㨻㩣㩚㩋㨷㨺㩖㩨)
*':#)10#.*'#&5.16 5+.+%1047$$'4
$1.6 %1&'01 %1&'01

㩃㩚㩆㨺㩣 59㨻㩣㩚㩋㨷㨺㩖㩨)‫ޓ‬
59㨻㩣㩚㩋㨷㨺㩖㩨)
5+.+%1047$$'4
%1&'01

6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/' 37#.+6;+56*'5#/'
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 (5: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 (5:

).:
A-5 㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
/7%4 A-6
%1&'01 ).:
6;2'
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;
࡙࠾࠶࠻ 70+6
Ꮏ੐᧚ᢱ⴫ ⴫␜ㇱ
(#4(%4 /7%45*-#6
+056#..#6+10/#6'4+#.5 &+52.#;70+6

⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂ ↪ㅜ㧛஻⠨
176.+0' 3 6; ੍஻ຠ 52#4'2#465
01 0#/' &'5%4+26+105 4'/#4-5
੍஻ຠ
㩃㨺㩖㩨㩣
% ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
49/ ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬ 52
%14'%#$.' 52#4'2#465
5+)0#.%#$.'
%1&'01 &%↪

੍஻ຠ 52#4'2#465
㩃㨺㩖㩨㩣
% ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬ ੍஻ຠ
49/ ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
%14'%#$.'
5+)0#.%#$.' 52
%1&'01
52#4'2#465

#%↪
㩃㨺㩖㩨㩣
% ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬ ઃዻຠ #%%'5514+'5
%14'%#$.'
5+)0#.%#$.' ઃዻຠ
%1&'01
(2
㩃㨺㩖㩨㩣
% ㆬᛯ‫ޓ‬61$'5'.'%6'& #%%'5514+'5
‫ޓޓޓޓޓޓޓޓޓޓ‬
%14'%#$.' Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
5+)0#.%#$.'
%1&'01
㩃㨺㩖㩨㩣⚵ຠ
&8+&&5.+0-/
%#$.'#55'/$.;

㪈㪅䍘䍎䍢䍼ᧃየ䈮㪲㪁㪁㪴䈱ઃ䈇䈢䍳䍤䍍䍢䈲ઍ⴫䈱ဳᑼ㪆䍘䍎䍢䍼䉕⴫␜䈚䈩䈇䉁䈜䇯
㪛㪦㪬㪙㪣㪜㩷㪘㪪㪫㪜㪩㪠㪪㪢㩷㪛㪜㪥㪦㪫㪜㪪㩷㪚㪦㪤㪤㪦㪥㪣㪰㩷㪬㪪㪜㪛㩷㪜㪨㪬㪠㪧㪤㪜㪥㪫㪅
㪉㪅੍஻ຠ䈲䇮㪘㪚↪㪃㪛㪚↪䈪ㆬᛯ㗿䈇䉁䈜䇯
㪚㪟㪦㪦㪪㪜㩷㪪㪧㪘㪩㪜㩷㪧㪘㪩㪫㪪㩷㪛㪜㪧㪜㪥㪛㪠㪥㪞㩷㪦㪥㩷㪘㪚㩷㪦㪩㩷㪛㪚㩷㪧㪦㪮㪜㪩㪅
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/' ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).: 㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩 ).:
A-7
)/:
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
/7%4 A-8
%1&'01 ).:
6;2'
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;
(2
࡙࠾࠶࠻ 70+6
ઃዻຠ⴫ ⴫␜ㇱ
(QT/7%4 /7%45*-#4
#%%'5514+'5 &+52.#;70+6

176.+0' 3 6; ੍஻ຠ 52#4'2#465
01 0#/' &'5%4+26+105 4'/#4-5
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
੍஻ຠ
㩔㩩㩒㩣㩀㩔㩨㨺
‫(ޓ‬14&+52.#;70+6
41*5 52
2#0'.%18'4 52#4'2#465
%1&'01 #%↪

41*5 ੍஻ຠ 52#4'2#465
㩔㩩㩒㩣㩖㨹㩂 ⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6 ੍஻ຠ

2#0'.*11-
52
%1&'01
52#4'2#465

&%↪
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷 ⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6 ઃዻຠ #%%'5514+'5
:575
5'.(6#22+0)5%4'9
ઃዻຠ
%1&'01
(2
#%%'5514+'5

Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
㩃㨺㩖㩨㩣⚵ຠ
&8+&&5.+0-/
%#$.'#55'/$.;

㪈㪅䍘䍎䍢䍼ᧃየ䈮㪲㪁㪁㪴䈱ઃ䈇䈢䍳䍤䍍䍢䈲ઍ⴫䈱ဳᑼ㪆䍘䍎䍢䍼䉕⴫␜䈚䈩䈇䉁䈜䇯
㪛㪦㪬㪙㪣㪜㩷㪘㪪㪫㪜㪩㪠㪪㪢㩷㪛㪜㪥㪦㪫㪜㪪㩷㪚㪦㪤㪤㪦㪥㪣㪰㩷㪬㪪㪜㪛㩷㪜㪨㪬㪠㪧㪤㪜㪥㪫㪅
㪉㪅੍஻ຠ䈲䍂㪘㪚㪃㪛㪚䈪ㆬᛯ㗿䈇䉁䈜䇯
㪚㪟㪦㪦㪪㪜㩷㪪㪧㪘㪩㪜㩷㪧㪘㪩㪫㪪㩷㪛㪜㪧㪜㪥㪛㪠㪥㪞㩷㪦㪥㩷㪘㪚㩷㪦㪩㩷㪛㪚㩷㪧㪦㪮㪜㪩㪅
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/' ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩 )/:
A-9 A-10
).:
427
%1&'01 ).:
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6; 6;2'
%2
࡙࠾࠶࠻ 70+6 #%↪
೙ᓮㇱ Ꮏ੐᧚ᢱ⴫
427
241%'551470+6 +056#..#6+10/#6'4+#.5

੍஻ຠ 52#4'2#465 176.+0' 3 6;
01 0#/' &'5%4+26+105 4'/#4-5
੍஻ຠ ೙ᓮㇱ↪‫ޓޓޓޓޓ‬
ᠲ૞㩤㩔㩨㨺
‫(ޓ‬14241%'5514
52 70+6
52#4'2#465 6'4/+0#.12'0'4

%1&'
01
੍஻ຠ ᠲ૞㩤㩔㩨㨺 ೙ᓮㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14241%'5514
52 70+6
52#4'2#465 6'4/+0#.12'0'4

%1&'
01
੍஻ຠ ࿶⌕┵ሶ ೙ᓮㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14241%'5514
52 (8 70+6
52#4'2#465 %4+/210.7)

%1&'
01
Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
%2
+056#..#6+10/#6'4+#.5

Ꮏ੐᧚ᢱ
%2
+056#..#6+10/#6'4+#.5

࿑ᦠ &1%7/'06
ขᛒ⺑᣿ᦠ
1/
12'4#614 5/#07#.

ขᛒ⺑᣿ᦠ
1/
12'4#614 5/#07#.

ⵝ஻ⷐ㗔ᦠ
+/
+056#..#6+10/#07#.

ᠲ૞ⷐ㗔ᦠ
15
12'4#614 5)7+&'

㪈㪅䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
㪉㪅䋨㪁㪈䋩䋨㪁㪉䋩䈲䇮䈠䉏䈡䉏઀᭽ㆬᛯຠ䉕⴫䈚䉁䈜䇯
䋨㪁㪈䋩䋨㪁㪉䋩㪠㪥㪛㪠㪚㪘㪫㪜㩷㪪㪧㪜㪚㪠㪝㪠㪚㪘㪫㪠㪦㪥㩷㪪㪜㪣㪜㪚㪫㪠㪭㪜㩷㪠㪫㪜㪤㪅
㪊㪅㩿㪁㪊㪀㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪઀᭽䈱ᤨ䈱䉂ᷝઃ䈘䉏䉁䈜䇯
㪪㪬㪧㪧㪣㪰㪜㪛㩷㪮㪠㪫㪟㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪㩷㪦㪥㪣㪰㪅 ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯 241&7%637#.+6;+56*'5#/'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).:
A-11 A-12
%1&'01 ).: %1&'01 ).:

6;2' %2 6;2' (2
&%↪
Ꮏ੐᧚ᢱ⴫ ઃዻຠ⴫
(QT4%7&GUMVQROQWPVMKV
+056#..#6+10/#6'4+#.5 #%%'5514+'5
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
ᠲ૞㩤㩔㩨㨺 ೙ᓮㇱ↪‫ޓޓޓޓޓ‬ -$⋥ઃ㊄ౕ ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14241%'5514 ‫(ޓ‬14%10641.70+6
70+6 41*5
6'4/+0#.12'0'4 -$(+:+0)/'6#.
%1&' %1&'
01 01
ᠲ૞㩤㩔㩨㨺 ೙ᓮㇱ↪‫ޓޓޓޓޓ‬ 㩂㩨㩥㩜㨹㩎 ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14241%'5514 ‫(ޓ‬14%10641.70+6
70+6 )
6'4/+0#.12'0'4 )41//'6
%1&' %1&'
01 01
࿶⌕┵ሶ ೙ᓮㇱ↪‫ޓޓޓޓޓ‬ 㩏㩗㩨㩈㩛㩇$ ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14241%'5514 ‫(ޓ‬14%10641.70+6
(8
.( 70+6 /:%9/$0+
%4+/210.7) 9#5*'4*'#&5&4'9$
%1&' %1&'
01 01
㩂㩢㨻㩔㩨㩧㩘㩩㩧 ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
6/
%75*+10
%1&'
01
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬ ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/' 241&7%637#.+6;+56*'5#/'

A-13 A-14
%1&'01 ).: %1&'01 ).:

6;2' (2 6;2' (2
ઃዻຠ⴫ ઃዻຠ⴫
(QT4%7&GUMVQROQWPVMKV (QT4%7(NWUJOQWPVMKV 1RVKQP
#%%'5514+'5 #%%'5514+'5
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
-$⋥ઃ㊄ౕ
6 ᠲ૞ㇱ↪‫ޓޓޓ‬ 㩖㩡㨹㩆㨷㩙㨽㩧㩎㊄ౕ
‫(ޓ‬14%10641.70+6
41*5 41*5
-';$1#4&(+:674' (.75*/1706+0)2.#6'
%1&' %1&'
01 01
㩖㩨㩡㨼㩧㩎㩨㩆㨺㩣 ᠲ૞ㇱ↪‫ޓޓޓ‬ 㩏㩗㩨㩈㩛㩇$
‫(ޓ‬14%10641.70+6
41*5 /:%9/$0+
$.+0&5'#. 9#5*'4*'#&5&4'9$
%1&' %1&'
01 01
㩂㩨㩥㩜㨹㩎 ᠲ૞ㇱ↪‫ޓޓޓ‬ ౐ⷺ㩏㨹㩎‫ޓ‬㧝⒳
‫(ޓ‬14%10641.70+6
) /575
)41//'6 *':076
%1&' %1&'
01 01
㩏㩗㩨㩈㩛㩇$ ᠲ૞ㇱ↪‫ޓޓޓ‬ Ⲕ㩘㩨㩣㩎
‫(ޓ‬14%10641.70+6
/:%9/$0+ /:575
9#5*'4*'#&5&4'9$ 9+0)5%4'9
%1&' %1&'
01 01
㩂㩢㨻㩔㩨㩧㩘㩩㩧 ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
6/
47$$'4(116
%1&'
01
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/' 241&7%637#.+6;+56*'5#/'

)1:
A-15 㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
A-16
%7(#4
%1&'01 ).:
6;2'
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;
(2
࡙࠾࠶࠻ 70+6
ઃዻຠ⴫ 㩜㩝㩢㨺㩀㨺㩎㩨㨼㩧㩊㨺㩖㨴㨼㩇
%7
#%%'5514+'5 /'/14;%#4&+06'4(#%'
⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂

↪ㅜ㧛஻⠨
176.+0' 3 6; Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
01 0#/' &'5%4+26+105 4'/#4-5
Ꮏ੐᧚ᢱ
ขᚻ
41*5 %2

*#0&.' +056#..#6+10/#6'4+#.5
%1&'
01
/%9㩘㩩㩢㩆㨺㩣 ߘߩઁᎿ᧚ 16*'4+056#..#6+10/#6'4+#.5
㩥㨺㩈㩨㨹㩎ᐳ㊄
㩃㨺㩖㩨㩣⚵ຠ 2'26:$.
/%9㩘㩩㩢㩆㨺㩣
415'66'9#5*'4
2'26:$.
%1&'
01 %#$.'#55;

ਣ⋁ዊ㩒㩆㩨
/:%9㩘㩩㩢㩆㨺㩣㩃㨺㩖㩨㩣⚵ຠ/,
18#.*'#&5%4'9
%1&' /,#52(%
01 %#$.'#55;
ᵄᐳ㊄
99575
9#8'9#5*'4
%1&'
01
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/' ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩 )1:
A-17 A-18
%1&'01 )1: %1&'01 )1:

6;2' %2 6;2' (2
Ꮏ੐᧚ᢱ⴫ ઃዻຠ⴫
+056#..#6+10/#6'4+#.5 #%%'5514+'5
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
⥽ベ⾍ࠅ㩙㨺㩂
$5* 㩔㩧㩀㩨㨺

56''4+0)9*''..#$'. /1706+0)$4#%-'6
%1&' %1&'
01 01
㩔㩨㩒ᐳ㊄㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷
/575 :575
524+0)9#5*'4 5'.(6#22+0)5%4'9
%1&' %1&'
01 01
㩚㩀㩨㩁ਣᐔᐳ㊄㩏㩗㩨㩈㩛㩇#
/575 /:%9/$0+
(.#69#5*'4 9#5*'4*'#&5%4'9
%1&' %1&'
01 01
/575
*':076
%1&'
01
ኸಾ㩘㩨㩣㩎
/:575
6*4'#&'&41&
%1&'
01
⥽ベ㩙㨺㩂⾍ઃⷐ㗔
%㩦㨾㨼
.#$'.#66#%*+0)
241%'&74' %1&'
01
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/' 241&7%637#.+6;+56*'5#/'
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 )1: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 )1:

)% ).:
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6; 0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;
੍஻ຠ 52#4'2#465 㩏㩗㩨㩈㩛㩇$

A-20
/:%9/$0+
੍஻ຠ
52 9#5*'4*'#&5%4'9

52#4'2#465
㩏㩗㩨㩈㩛㩇#
/:%9/$0+
ߘߩઁㇱຠ 16*'42#465
9#5*'4*'#&5%4'9
)%㩀㩔㩨㨺⚵ຠ

㩄㩒㩂㩊

)%%18'4#55; (74
%100'%614
0*㩄㩒㩂㩊

2
㩄㩒㩂㩊

0*%100'%614#55; (74
%100'%614
8*㩄㩒㩂㩊

2
8*%100'%614#55;

8*㩄㩒㩂㩊

2
8*%100'%614#55;

:*2*㩄㩒㩂㩊

2
:*2*%100'%614#55;

Ṷ▚㩖㩩㩢㩧㩎
2#
.(
241%'5514$1#4&

㩏㩗㩨㩈㩛㩇$
/:%9/$0+
9#5*'4*'#&5%4'9
$

ဳᑼ䎒䱤䱚䱮䲈⇟ภ䬛䯾Ბ䬽႐ว䫺ਅᲑ䭗䭙਄Ბ䬺ઍ䭞䭚ㆊᷰᦼຠ䬶䬑䭙䫺䬸䬰䭘䬚䬛౉䬲䬵䬓䭍䬨䫻䫹䬹䬙䫺ຠ⾰䬾ᄌ䭞䭙䭍䬪䭢䫻
䯴⇛࿑䬽ኸᴺ䬾䫺ෳ⠨୯䬶䬨䫻䎃䎧䎬䎰䎨䎱䎶䎬䎲䎱䎶䎃䎬䎱䎃䎧䎵䎤䎺䎬䎱䎪䎃䎩䎲䎵䎃䎵䎨䎩䎨䎵䎨䎱䎦䎨䎃䎲䎱䎯䎼䎑䯵䎷䎺䎲䎃䎷䎼䎳䎨䎶䎃䎤䎱䎧䎃䎦䎲䎧䎨䎶䎃䎰䎤䎼䎃䎥䎨䎃䎯䎬䎶䎷䎨䎧䎃䎩䎲䎵䎃䎤䎱䎃䎬䎷䎨䎰䎑䎃䎃䎷䎫䎨䎃䎯䎲䎺䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎃䎰䎤䎼䎃䎥䎨䎃䎶䎫䎬䎳䎳䎨䎧䎃䎬䎱䎃䎳䎯䎤䎦䎨䎃䎲䎩䎃䎷䎫䎨䎃
䎸䎳䎳䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎑䎃䎴䎸䎤䎯䎬䎷䎼䎃䎬䎶䎃䎷䎫䎨䎃䎶䎤䎰䎨䎑 ).:
)1:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
A-19

)1:
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
3 6;
ᢙ㊂
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕

(2
41*5
%0)3'27.
/:%9/$0+
&'5%4+26+105
ဳฬ㧛ⷙᩰ
/575
/575
/575
%1&'01
%1&'01
%1&'01
%1&'01
%1&'01
%1&'01
%1&'01
6;2'
⇛‫ޓޓ‬࿑
176.+0'
9#5*'4*'#&5%4'9
/1706+0)$4#%-'6
ฬ‫ޓޓ‬⒓
㩄㩧㩉㨺㩣㩠㨽ขઃ᧚
524+0)9#5*'4
0#/'
ઃዻຠ⴫
37#.+6;+56*'5#/'
㩚㩀㩨㩁ਣᐔᐳ㊄
(.#69#5*'4
㩏㩗㩨㩈㩛㩇#
#%%'5514+'5
)41//'6
*':076
㩔㩨㩒ᐳ㊄
㩂㩨㩥㩜㨹㩎
⇟ภ
01

).:
A-21 A-22
2/
%1&'01 ).:
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6; 6;2'
12
࡙࠾࠶࠻ 70+6
㩇㩁㨶㩏㩀㩔㩨㨺2/⚵ຠ Ꮏ੐᧚ᢱ⴫
12
5%#00'4%18'4#55'/$.; +056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5 12 176.+0' 3 6;
01 0#/' &'5%4+26+105 4'/#4-5
㩆㩨㨷㩧㩀㩌㩂㩨㩢㨺㩇
㩏㩗㩨㩈㩛㩇$
㩖㩩㩡㩇㩍㨲㩣㨺㩖㩨)㨼㩢 /:%9/$0+

)4'#5' 9#5*'4*'#&5&4'9$
%1&'
01
Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
ㅪ⚿บ
⚵ຠ
5/:*㩄㩒㩂㩊
12
%172.+0)2.#6'#55;

22
%1&'
5/:*%100'%614 01

ษࠅ㊄ౕ
41*5
.+(6+0)(+:674'

㩀㩔㩨㨺↪㩔㩩㨹㩁㩧

2#%-+0)

࿑ᦠ &1%7/'06
2/ขઃᦠ
%
12'4#614 5/#07#.

ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯 241&7%637#.+6;+56*'5#/'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).:
).:
A-23 A-24
12
%1&'01 ).:
6;2'
0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;
12
ߘߩઁㇱຠ 16*'42#465
Ꮏ੐᧚ᢱ⴫ 㩏㩗㩨㩈㩛㩇$
/:%9/$0+
+056#..#6+10/#6'4+#.5 9#5*'4*'#&5%4'9
⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂

↪ㅜ㧛஻⠨
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 &8+4)$⚵ຠ
㩏㩗㩨㩈㩛㩇$ 5.$(40#
&8+4)$#55;
/:%9/$0+
9#5*'4*'#&5&4'9$
%1&'
01 4)$$7((㩖㩩㩢㩧㩎
ㅪ⚿บ
⚵ຠ 2$
.(
4)$$7(($1#4&
12
%172.+0)2.#6'#55;

%1&'
01 8*㩄㩒㩂㩊

2
8*%100'%614

:*㩄㩒㩂㩊

2
:*%100'%614

:*㩄㩒㩂㩊

2
:*%100'%614

㩃㨺㩖㩨㩣⚵ຠ &8+&&5.+0-/
&8+&&5.+0-/
%#$.'#55;

㩇㩗㩩㨺㩅㨺
53
52#%'4

㩔㩨㩒㩅㩨㩀㩨㩒
/%9
524+0)9#5*'4

ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/' ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕

A-25 For antenna unit motor A-26
%1&'01 ).:

6;2' %2
Ꮏ੐᧚ᢱ⴫
+056#..#6+10/#6'4+#.5
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
㩄㩒㩂㩊
㩝㩆㩨㨷㩡㨺
/25%
/1&7.#4%100%614
%1&'
01

For display unit (MU-201CR/231CR, AC set)

For display unit (MU-201CR, DC set)
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).:

For display unit (MU-231CR, DC set) A-27 For processor unit (24 VDC set) A-28

For processor unit (100 VAC set) For GC-10

For processor unit (220 VAC set)

A-29 A-30
%1&'01 ).: %1&'01 )/:

6;2' (2 6;2' (2
ઃዻຠ⴫ ઃዻຠ⴫
#%%'5514+'5 #%%'5514+'5
01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
㩔㩧㩀㩨㨺.
41*5 㩔㩧㩀㩨㨺.
41*5

*#0)'4. *#0)'4.
%1&'01 %1&'01

㩔㩧㩀㩨㨺4
41*5 㩔㩧㩀㩨㨺4
41*5

*#0)'44 *#0)'44
%1&'01 %1&'01

㩔㩧㩀㩨㨺㩅㩅㨾
㩔㩧㩀㩨㨺㩅㩅㨾

41*5 41*5
*#0)'456#; *#0)'456#;
%1&'01 %1&'01

㩘㨺㩣㩖㩩㩡㩂㩨㩘㨺㩣㩖㩩㩡㩂㩨
%2*2 %2*2
*1.'2.7) *1.'2.7)
%1&'01 %1&'01

㩇㩏㨹㩖㩩㩘㩨㩊㩧㩇㩏㨹㩖㩩㩘㩨㩊㩧
-$㩠㨽‫ޓ‬㩘㩨㩊㩧㩂㩥 -$㩠㨽‫ޓ‬㩘㩨㩊㩧㩂㩥
50#2$76610 50#2$76610
%1&'01 %1&'01

㩚㩀㩨㩁ᐔᐳ㊄㩚㩀㩨㩁ᐔᐳ㊄
/575 /575
(.#69#5*'4 (.#69#5*'4
%1&'01 %1&'01

㩔㩨㩒ᐳ㊄㩔㩨㩒ᐳ㊄
/575‫ޓ‬ /575‫ޓ‬
524+0)9#5*'4 524+0)9#5*'4
%1&'01 %1&'01

౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎 ౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎
/:575 /:575
*':$1.6 *':$1.6
%1&'01 %1&'01

౐ⷺ㩇㩢㩦㩢㩈㩛㩇$ ౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
/:575 /:575
*':$1.6 *':$1.6

5.166'&9#5*'4*'#& %1&'01
5.166'&9#5*'4*'#& %1&'01

6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6 6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/' 37#.+6;+56*'5#/'
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 ).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰 )/:

This page intentionally left blank.
D-1
D-2
Jun.11'08 R.Esumi
D-3
D-4
D-5
D-6
D-7
D-8
D-9
D-10
D-11
D-12
D-13
/C[ 4'UWOK
esumi 電子署名者 : esumi

DN: cn=esumi, c=JP - 日本, o=kisou, ou=toukatu, [email protected]
日付 : 2007.12.26 17:43:45 +09'00'
1/Sep/2010 Y.NISHIYAMA
D-14
D-15
D-16
1/Sep/2010 Y.NISHIYAMA
D-17
Jan.18'08 R.Esumi
D-18
#RT 4'UWOK
D-19
電子署名者 : esumi
日付 : 2007.12.26 17:44:45 +09'00'
esumi
#RT 4'UWOK
D-20
日付 : 2007.12.26 17:45:10 +09'00'
esumi
#RT 4'UWOK
D-21
日付 : 2007.12.26 17:44:02 +09'00'
esumi
#RT 4'UWOK
D-22
日付 : 2007.12.26 17:44:16 +09'00'
esumi
D-23
#RT 4'UWOK
日付 : 2007.12.26 17:44:31 +09'00'
esumi
D-24
D-25
D-26
D-27
D-28
D-29
D-30
D-31
Apr. 05 '04
D-32
D
C
B
A
110/115/ *1 *2
*5 :
*4 :
注記
*3 :
*2 :
*1 :
220/230VAC, DPYC-1.5
RU-3305
1φ,50-60Hz TB901
100VAC,1φ, DPYCY-1.5 *1 1 100VAC-H
IV-8sq. *1 *5
保護アース PE
50-60Hz 2 100VAC-C
氷結防止用 3 NC
*1
オプション
造船所手配
保護ｱｰｽ
PE *1 *5
440VAC DPYC-1.5 FOR DE-ICER *4
IV-3.5sq.
RSB-096/097
1φ,50-60Hz
1
トランス
J1 J603(XH) J613 *3
RU-1803 *2
*1
TRANSFORMER
100-120/ TB1 9 03-2088(6-14P) 1 GC_LED TX_HV 1 RW-9600,15/30/40/50m,φ22 TB-801
RW-4747
DPYC-2.5 10 2 GC_HOLD チャ 1
BOARD
200-240VAC 1 H NC 2 BRN TX_HV
1φ,50-60Hz 2 C 03-2090(3P) J5(VH) 11 3 GC_UP J610 2 NC
RSB-109(FAR-2127-5A)
1 GYRO_R2 12 4 GC_DOWN 24V_PLUS 1 ダイ(太) ORG[B] 3 24V_PLUS

*1
空中線部 ANTENNA UNIT
J602 2 GYRO_R1 13 5 GC_0V 24V_MINUS 2 キ(太) YEL[B] 4 24V_MINUS
64P1106A *2
MPYC-7 1 チャ BRN 3 14 6 アオ(太) 5
GYROCOMPASS NC GC_5V MOTOR(+) 3 BLU[B] MOTOR(+)
GYRO CONVERTER
2 アカ RED J4(VH) J7(NH) 03-2091(5P) J608 MOTOR(+) 4 ハイ(太) GRY[B] 6 MOTOR(+)
3 ダイ ORG 1 GYRO_S1 DATA1-H 1 チャ BRN 1 AD_DATA-H MOTOR(-) 5 ﾑﾗｻｷ(太) PPL[B] 7 MOTOR(-)
P
4 キ YEL 2 GYRO_S2 DATA1-C 2 アカ RED 2 AD_DATA-C MOTOR(-) 6 シロ(太) WHT[B] 8 MOTOR(-)
船内配電盤では3Aのブレーカを使用。
5 ﾐﾄﾞﾘ GRN 3 GYRO_S3 SHIFT1-H 3 ダイ ORG 3 AD_CLK-H SPU_RF_D-A 7 アカ RED 9 SPU_RF_D-A
P
PM-31
6 アオ BLU 4 GYRO_T SHIFT1-C 4 キ YEL 4 AD_CLK-C SPU_RF_D-B 8 ﾐﾄﾞﾘ GRN 10 SPU_RF_D-B

7 ﾑﾗｻｷ PPL 5 GYRO_FG FG 5 RF_SPU_D-A 9 クロ BLK 11 RF_SPU_D-A
03-2089(5P) RF_SPU_D-B 10 シロ WHT 12 RF_SPU_D-B
*1 ﾐﾄﾞﾘ(太) 13
SG 11 GRN[B] SG
A-D CONVERTER TTYCS-4 GND 12 アカ(太) RED[B] 14 GND
最長 100m (延長するときは接続箱RJB-001が必要 )
PERFORMANCE MONITOR
J609 TB-802
IF_VIDEO IF_VIDEO
パフォーマンスモニター
保護アース用ケーブルは緑／黄の絶縁線を使用のこと。
03P9342
GND GND
*1
TB BOARD
J2 J1 J9 J3
VGA CABLE 1 R_VIDEO R_VIDEO 1 5 R 1
RGB EXT. MONITOR 合計：31.5m以下 TOTAL: UP TO 31.5m
2 G_VIDEO GND 2 6 GND 2
3 B_VIDEO G_VIDEO 3 7 G XH10P-W-6P XH10P-W-5P-A
4 NC GND 4 8 GND
2.3/10/20/30m,φ9 1.5/10/20/30m,φ9
2
5 NC B_VIDEO 5 9 B
SLB-FRN4-A
*1 6 GND GND 6 10 GND J602 J501/J521 J502/J522 J501
COAX.(75Ω)ｘ5
NOTES
VDR 7 GND H_SYNC 7 3 HS KEY_TXD-B 1 1 KEY_TXD-B KEY_TXD-B 1 1 KEY_TXD-B
03P9229A
DVI-RGB変換基板
8 GND GND 8 4 GND KEY_TXD-A 2 2 KEY_TXD-A KEY_TXD-A 2 2 KEY_TXD-A
DSUB-BNC-1
9 NC V_SYNC 9 1 VS 23 KEY_RXD-B 3 3 KEY_RXD-B KEY_RXD-B 3 3 KEY_RXD-B
*2: OPTION
CONVERTER *2
10 GND GND 10 2 GND 24 KEY_RXD-A 4 4 KEY_RXD-A KEY_RXD-A 4 4 KEY_RXD-A
RGB BUFFER PCB

RGB ﾊﾞｯﾌｧ基板
BNC CONNECTOR
BNCｺﾈｸﾀｺﾝﾊﾞｰﾀ
11 GND VCC 11 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
12 NC GND 12 GND 6 6 GND GND 6 6 GND
DVI-RGB CONVERSION BOARD

13 H_SYNC -5/-12V 13 +12V 7 7 +12V +12V 7 7 +12V
*1: SHIPYARD SUPPLY

14 Y_SYNC GND 8 8 GND GND 8 8 GND
15 NC SYS_FAIL-H 9 9 SYS_FAIL-H NC 9 9 NC
NC
NC
GND
GND
+12V
+12V
-5/-12V
GND
VCC
J3
J4
SYS_FAIL-C 10 10 SYS_FAIL-C NC 10 10 NC
6
5
4
3
2
1
3
2
1
DVI-RGB-1 *2
J507/J527
RGBﾋﾞﾃﾞｵｺﾝﾊﾞｰﾀ
*2
RCU-016
CONTROL UNIT
操作部
RGB VIDEO CONVERTOR

1 SYS_FAIL-H
J615 J622 2 SYS_FAIL-C
操作部
チャ BRN 1 +12V SYS_ACK-H 1 3 SYS_ACK-H
1φ,50/60Hz
2 2
RCU-014/015
アカ RED GND SYS_ACK-C 4 SYS_ACK-C

CONTROL UNIT
ダイ ORG 3 +5V
キ YEL 4 GND
5
IV-8sq. *1 *5
保護アース PE
ﾐﾄﾞﾘ GRN -12V J601
NC 1
100-230VAC DPYC-2.5
*1
*5: USE GRN/YEL WIRE FOR PROTECTIVE EARTH.

RXD 2
TXD 3
*4: USE 3A BREAKER IN SHIP'S MAINS SWITCH BOX.

DVI-D MONITOR NC 4
RS-232C CABLE *1
2 C
1 H
J3 J204 GND 5 PC
TB1
DVI-D/DSINGLELINK5M/10M,
3
TMDS_DATA2(-) 1 1 DVI0TX2_N NC 6
RS-232C
MODEL
TMDS_DATA2(+) 2 5/10m,φ7 2 DVI0TX2_P NC 7
TMDS_DATA2/4_SHIELD 3 3 A_GND NC 8
NC 4 4 NC NC 9
NC 5 5 NC *1
FAR-2817/2827
FAR-2117/2127
DDC_CLOCK 6 6 NC J605
DDC_DATA 7 7 HDG-A 1
TTYCS-1Q HDG SENSOR
NC
*3: MAX. 100m (JUNCTION BOX RJB-001 IS REQUIRED FOR EXTENSION)

P (IEC-61162-2)
NC 8 8 NC HDG-B 2
TMDS_DATA(-) 9 9 DVI0TX1_N HDG_GND 3
TMDS_DATA(+) 10 10 DVI0TX1_P *1
MONITOR
RPU-013
TMDS_DATA1/3_SHIELD 11 11 A_GND J606

12 12 NAV-A 1
TTYCS-1
NC NC NAVIGATOR
P
NC 13 13 NC NAV-B 2
MU-231/231CR
MU-190/201CR
(IEC-61162-1)
+5V_POWER 14 14 VCC NC 3
制御部
GND 15 15 GND
16 16
*1
J607
表示部 MONITOR UNIT

HOT_PLUG_DETECT NC
17 17 LOG-A 1
TTYCS-1
TMDS_DATAB(-) DVI0TXD_N SPEED LOG
MU-190/201CR/231/231CR
P
TMDS_DATAB(+) 18 18 DVI0TXD_P LOG-B 2 (IEC-61162-1)
PROCESSOR UNIT
NC 20 20 NC
21 21
*1
NC NC J619
22 22 ARPA-A 1
TTYCS-1
TMDS_CLOCK_SHIELD A_GND ECDIS
P
TMDS_CLOCK(+) 23 23 DVI0TXC_P ARPA-B 2 (IEC-61162-1)
TMDS_CLOCK(-) 24 24 DVI0TXC_N NC 3
IV-8sq. *1 *5
保護アース PE
*1
4
J620
TRK_TD-A 1
TTYCS-4
P TRACK_CONTROL
DVI-D MONITOR TRK_TD-B 2
*2 TRK_RD-A 3 (IEC-61162-1)
外部モニター J205
DVI CABLE P
1 SAME AS AVOBE TRK_RD-B 4
EXT. MONITOR 2 GND 5
J621
24 RSV1_TD-A 1
RSV1_TD-B 2 NOT USED
GND 3
RSV2_TD-A 4
RSV2_TD-B 5
SCALE
DRAWN GND 6
J1 MJ-A3SPF MJ-A3SPF0015,10m,φ6 J614
DWG.No.
CHECKED
APPROVED
+12V 1 シロ WHT 1 +12V
2 GND
*1
GND 2 クロ BLK J611
CU-200
AIS_TD-A 1
TTYCS-4
FG 3 P AIS
AIS_TD-B 2 (IEC-61162-2)
MPS588-C NETWORK AIS_RD-A 3
J302
9/Aug/2010
9/Aug/2010
P5E-4PTX-BL,10m,φ6.3 P
10/Aug/2010
TXP 1 1 TXP AIS_RD-B 4
P
2 2 AIS_GND 5
MASS
TXN TXN
RXP 3 3 RXP *1
防水型ｶｰﾄﾞｲﾝﾀｰﾌｪｲｽ
NC 4 4 NC J612
LAN
P TTYCS-7
C3519-C01- T
MEMORY CARD I/F UNIT
NC 5 5 NC ALARM1_0 1 ALARM SYSTEM

P
RXN 6 6 RXN ALARM1_1 2
T.YAMASAKI
Y.NISHIYAMA
5
kg
7 7 ALARM2_0 3
*2
NC NC
T.TAKAHASHI
P
NC 8 8 NC ALARM2_1 4
ALARM3_0 5
IV-1.25sq.
*1
*1 P
LAN CABLE(CAT5) OR ALARM3_1 6
REF.No.
MPS588-C FR-FTPC-CY,10/20/30m,φ13 OPERATOR_FITNESS_0 7

P
TXP 1 シロ/ﾐﾄﾞﾘ WHT/GRN OPERATOR_FITNESS_1 8
P
TXN 2 ミドリ GRN EXT_ALM_ACK_N 9
P
RXP 3 シロ/ダイ WHT/ORG GND 10
NC 4 アオ BLU SYS_FAIL-H 11
P P
NC 5 シロ/アオ WHT/BLU SYS_FAIL-C 12
RXN 6 ダイ ORG
ｽｲｯﾁﾝｸﾞﾊﾌﾞ
NC 7 シロ/チャ WHT/BRN J616(NH)

SWITCHING HUB
保護アース PE
RW-4864,φ9.5
NC 8 チャ BRN GND 1
IV-1.25sq.*1 *5
MASTER RADAR
03-163-6001-7
OP_HD_IN 2
HUB-100 (8 PORTS)
NR203PF-VVS1.25
*2
AC 1 100-230VAC GND 3
3.5m, φ8.6
AC 2 1φ,50/60Hz OP_BP_IN 4
GND 3 GND 5
OP_TRIG_IN 6
GND 7
NAME
TYPE
名称
OP_VIDEO_IN 8
BRC
J1 *1 J662
DPYC-1.5
03P9485
1 1 MOTOR_DO J617(NH)
RW-4864,φ9.5
2 2 MOTOR_C GND 1 SUB DISPLAY1
OP_HD_1 2
BRU-001/002
1
2
3
4
6
5
GND 3
(FULL-LOG)
BRAKE UNIT *2
ブレーキユニット
6
OP_BP_1 4
J105 J652 GND 5
1 1 OP_TRIG_1 6
相互結線図
2 2 GND 7
03P9339
3 3 OP_VIDEO_1 8
4 4
PWR PCB
5 5 J618(NH)
RW-4864,φ9.5
MARINE RADAR/ARPA
6 6 GND 1 SUB DISPLAY2

OP_HD_2 2
船舶用レーダー/ARPA
10 10 GND 3
(SEMI-LOG)
OP_BP_2 4
INTERCONNECTION DIAGRAM
GND 5
OP_TRIG_2 6
GND 7
OP_VIDEO_2 8
FAR-2117/2127/2817/2827 (AC SET)
S-1
D
C
B
A
110/115/ *1 *2
*5 :
*4 :
注記
*3 :
*2 :
*1 :
220/230VAC, DPYC-1.5
RU-3305
1φ,50-60Hz TB901
100VAC,1φ, DPYCY-1.5 *1 1 100VAC-H
IV-8sq. *1 *5
保護アース PE
50-60Hz 2 100VAC-C
氷結防止用 3 NC
空中線部
*1
保護ｱｰｽ
100/110/115/
PE *1 *5
FOR DE-ICER *4
IV-3.5sq.
200/220/230VAC DPYC-2.5
オプション。
造船所手配。
整流器
RSB-096/097
1φ,50/60Hz
1
ANTENNA UNIT
RECTIFIER
J1 J603(XH) J613 *3
RU-3424 *2
*1 9 03-2088(6-14P) 1 GC_LED
TB1 TX_HV 1 RW-9600,15/30/40/50m,φ22 TB-801
RW-4747
DPYC-6 10 2 GC_HOLD チャ 1
BOARD
12-24VDC 1 (+) NC 2 BRN TX_HV
2 (-) 03-2090(3P) J5(VH) 11 3 GC_UP J610 2 NC
1 GYRO_R2 12 4 GC_DOWN 24V_PLUS 1 ダイ(太) ORG[B] 3 24V_PLUS
*1 2 13 5 GC_0V キ(太) 4
J602 GYRO_R1 24V_MINUS 2 YEL[B] 24V_MINUS
64P1106A *2
MPYC-7 1 チャ BRN 3 14 6 アオ(太) 5
GYROCOMPASS NC GC_5V MOTOR(+) 3 BLU[B] MOTOR(+)
GYRO CONVERTER
2 アカ RED J4(VH) J7(NH) 03-2091(5P) J608 MOTOR(+) 4 ハイ(太) GRY[B] 6 MOTOR(+)
3 ダイ ORG 1 GYRO_S1 DATA1-H 1 チャ BRN 1 AD_DATA-H MOTOR(-) 5 ﾑﾗｻｷ(太) PPL[B] 7 MOTOR(-)
P
4 キ YEL 2 GYRO_S2 DATA1-C 2 アカ RED 2 AD_DATA-C MOTOR(-) 6 シロ(太) WHT[B] 8 MOTOR(-)
船内配電盤では3Aのブレーカを使用。
5 ﾐﾄﾞﾘ GRN 3 GYRO_S3 SHIFT1-H 3 ダイ ORG 3 AD_CLK-H SPU_RF_D-A 7 アカ RED 9 SPU_RF_D-A
P
PM-31
6 アオ BLU 4 GYRO_T SHIFT1-C 4 キ YEL 4 AD_CLK-C SPU_RF_D-B 8 ﾐﾄﾞﾘ GRN 10 SPU_RF_D-B

7 ﾑﾗｻｷ PPL 5 GYRO_FG FG 5 RF_SPU_D-A 9 クロ BLK 11 RF_SPU_D-A
03-2089(5P) RF_SPU_D-B 10 シロ WHT 12 RF_SPU_D-B
*1 ﾐﾄﾞﾘ(太) 13
SG 11 GRN[B] SG
A-D CONVERTER TTYCS-4 GND 12 アカ(太) RED[B] 14 GND
PERFORMANCE MONITOR
J609 TB-802
最長 100m (延長するときは接続箱RJB-001が必要 )。
IF_VIDEO IF_VIDEO
パフォーマンスモニター
保護アース用ケーブルは緑／黄の絶縁線を使用のこと。
03P9342
GND GND
*1
TB BOARD
J2 J1 J9 J3
RGB EXT. MONITOR VGA CABLE 1 R_VIDEO R_VIDEO 1 5 R 1 合計：31.5m以下 TOTAL: UP TO 31.5m
2 G_VIDEO GND 2 6 GND 2
3 B_VIDEO G_VIDEO 3 7 G XH10P-W-6P XH10P-W-5P-A
4 NC GND 4 8 GND 1.5/10/20/30m,φ9
2.3/10/20/30m,φ9
2
5 NC B_VIDEO 5 9 B
SLB-FRN4-A
*1 6 GND GND 6 10 GND J602 J501/J521 J502/J522 J501
COAX.(75Ω)ｘ5
NOTES
VDR 7 GND H_SYNC 7 3 HS KEY_TXD-B 1 1 KEY_TXD-B KEY_TXD-B 1 1 KEY_TXD-B
03P9229A
DVI-RGB変換基板
8 GND GND 8 4 GND KEY_TXD-A 2 2 KEY_TXD-A KEY_TXD-A 2 2 KEY_TXD-A
DSUB-BNC-1
9 NC V_SYNC 9 1 VS 23 KEY_RXD-B 3 3 KEY_RXD-B KEY_RXD-B 3 3 KEY_RXD-B
*2: OPTION.
CONVERTER *2
10 GND GND 10 2 GND 24 KEY_RXD-A 4 4 KEY_RXD-A KEY_RXD-A 4 4 KEY_RXD-A
RGB BUFFER PCB

RGB ﾊﾞｯﾌｧ基板
BNC CONNECTOR
BNCｺﾈｸﾀｺﾝﾊﾞｰﾀ
11 GND VCC 11 PWR_SW 5 5 PWR_SW PWR_SW 5 5 PWR_SW
12 NC GND 12 GND 6 6 GND GND 6 6 GND
DVI-RGB CONVERSION BOARD

13 H_SYNC -5/-12V 13 +12V 7 7 +12V +12V 7 7 +12V
14 Y_SYNC GND 8 8 GND GND 8 8 GND
*1: SHIPYARD SUPPLY.

15 9 9
100-115/
NC SYS_FAIL-H 9 9 SYS_FAIL-H NC NC
NC
NC
GND
GND
+12V
+12V
-5/-12V
GND
VCC
24VDC
J3
J4
SYS_FAIL-C 10 10 SYS_FAIL-C NC 10 10 NC
1φ,50/60Hz
6
5
4
3
2
1
3
2
1
DVI-RGB-1 *2
J507/J527
RGBﾋﾞﾃﾞｵｺﾝﾊﾞｰﾀ
*2
RCU-016
CONTROL UNIT
操作部
RGB VIDEO CONVERTOR

1 SYS_FAIL-H
100-230VAC
J615 J622 2 SYS_FAIL-C
1φ,50/60Hz
操作部
チャ BRN 1 +12V SYS_ACK-H 1 3 SYS_ACK-H

2 2
*1
RCU-014/015
アカ RED GND SYS_ACK-C 4 SYS_ACK-C

CONTROL UNIT
ダイ ORG 3 +5V
キ YEL 4 GND
IV-8sq.
*1
ﾐﾄﾞﾘ GRN 5 -12V J601
整流器
NC 1
DPYC-2.5
DPYC-2.5
*1
*1
IV-8sq. *1 *5
保護アース PE
*5: USE GRN/YEL WIRE FOR PROTECTIVE EARTH.

RXD 2
200-230VAC DPYC-1.5 RECTIFIER

TXD 3
RU-3423 *2
*4: USE 3A BREAKER IN SHIP'S MAINS SWITCH BOX.

NC 4
RS-232C CABLE *1
2
1
DVI-D MONITOR GND 5 PC
3
J3
2 -
1 +
J3 J204 NC 6
RS-232C
TB1
TB1
1 1
DVI-D/DSINGLELINK5M/10M, 1
TMDS_DATA2(-) DVI0TX2_N NC 7
TMDS_DATA2(+) 2 5/10m,φ7 2 DVI0TX2_P NC 8
NC 4 4 NC
5 5
*1
表示部
NC NC J605
TTYCS-1Q HDG SENSOR
同上 DITTO
24 DDC_CLOCK 6 6 NC HDG-A 1
P (IEC-61162-2)
または OR
*3: MAX. 100m. (JUNCTION BOX RJB-001 IS REQUIRED FOR EXTENSION)

DDC_DATA 7 7 NC HDG-B 2
MU-190/231
IV-8sq.
*1
NC 8 8 NC HDG_GND 3
MONITOR UNIT
TMDS_DATA(-) 9 9 DVI0TX1_N
10 10
*1
TMDS_DATA(+) DVI0TX1_P J606
MU-201CR/231CR
11 11 NAV-A 1
TTYCS-1
TMDS_DATA1/3_SHIELD A_GND NAVIGATOR
P
NC 12 12 NC NAV-B 2 (IEC-61162-1)
NC 13 13 NC NC 3
制御部
RPU-013
14 14
表示部 MONITOR UNIT

+5V_POWER VCC *1
MODEL
GND 15 15 GND J607
16 16 LOG-A 1
TTYCS-1
HOT_PLUG_DETECT NC
P
SPEED LOG
TMDS_DATAB(-) 17 17 DVI0TXD_N LOG-B 2 (IEC-61162-1)
TMDS_DATAB(+) 18 18 DVI0TXD_P NC 3
PROCESSOR UNIT
FAR-2817/2827
FAR-2117/2127
TMDS_DATA0/5_SHIELD 19 19 A_GND
20 20
*1
NC NC J619
21 21 ARPA-A 1
TTYCS-1
NC NC ECDIS
P
TMDS_CLOCK_SHIELD 22 22 A_GND ARPA-B 2 (IEC-61162-1)
TMDS_CLOCK(+) 23 23 DVI0TXC_P NC 3
MONITOR
TMDS_CLOCK(-) 24 24 DVI0TXC_N
IV-8sq.
*1
*1
4
J620
TRK_TD-A 1
TTYCS-4
MU-231/231CR
MU-190/201CR
P TRACK_CONTROL
DVI-D MONITOR TRK_TD-B 2
*2 TRK_RD-A 3 (IEC-61162-1)
外部モニター J205
DVI CABLE P
1 SAME AS AVOBE TRK_RD-B 4
EXT. MONITOR 2 GND 5
J621
24 RSV1_TD-A 1
RSV1_TD-B 2 NOT USED
J1 MJ-A3SPF J614 GND 3
MJ-A3SPF0015,10m,φ6
+12V 1 シロ WHT 1 +12V RSV2_TD-A 4
GND 2 クロ BLK 2 GND RSV2_TD-B 5
CU-200
SCALE
DRAWN GND 6
FG 3
DWG.No.
CHECKED
APPROVED
NETWORK *1
J302 MPS588-C P5E-4PTX-BL,10m,φ6.3 J611
1 1 AIS_TD-A 1
TTYCS-4
TXP TXP AIS
P P
TXN 2 2 TXN AIS_TD-B 2 (IEC-61162-2)
RXP 3 3 RXP AIS_RD-A 3
20/Aug/2010
20/Aug/2010
P
23/Aug/2010
防水型ｶｰﾄﾞｲﾝﾀｰﾌｪｲｽ
NC 4 4 NC AIS_RD-B 4
LAN
P
MEMORY CARD I/F UNIT
5 5 AIS_GND 5
MASS
NC NC
RXN 6 6 RXN
J612
*1
7 7
*2
NC NC TTYCS-7
NC 8 8 NC ALARM1_0 1
C3519-C02- S
ALARM SYSTEM
IV-1.25sq.
*1
P
*1 ALARM1_1 2
5
T.YAMASAKI
kg
LAN CABLE(CAT5) OR ALARM2_0 3

Y. NISHIYAMA
T.TAKAHASHI
P
MPS588-C FR-FTPC-CY,10/20/30m,φ13 ALARM2_1 4
TXP 1 シロ/ﾐﾄﾞﾘ WHT/GRN ALARM3_0 5
P P
TXN 2 ミドリ GRN ALARM3_1 6
REF.No.
RXP 3 シロ/ダイ WHT/ORG OPERATOR_FITNESS_0 7

P
NC 4 アオ BLU OPERATOR_FITNESS_1 8
P
NC 5 シロ/アオ WHT/BLU EXT_ALM_ACK_N 9
P
RXN 6 ダイ ORG GND 10
ｽｲｯﾁﾝｸﾞﾊﾌﾞ
NC 7 シロ/チャ WHT/BRN SYS_FAIL-H 11

SWITCHING HUB
保護アース PE
P
NC 8 チャ BRN SYS_FAIL-C 12
IV-1.25sq. *1 *5
HUB-100 (8 PORTS)
NR203PF-VVS1.25
*2
AC 1 100-230VAC J616(NH)
3.5m, φ8.6 RW-4864,φ9.5
AC 2 1φ,50/60Hz GND 1 MASTER RADAR
GND 3 OP_HD_IN 2
03-163-6001-7
GND 3
OP_BP_IN 4
GND 5
OP_TRIG_IN 6
GND 7
NAME
TYPE
名称
OP_VIDEO_IN 8
BRC
J1 *1 J662
DPYC-1.5
03P9485
1 1 MOTOR_DO J617(NH)
RW-4864,φ9.5
2 2 MOTOR_C GND 1 SUB DISPLAY1
OP_HD_1 2
BRU-001/002
1
2
3
4
6
5
GND 3
(FULL-LOG)
BRAKE UNIT *2
ブレーキユニット
6
OP_BP_1 4
J105 J652 GND 5
1 1 OP_TRIG_1 6
相互結線図
2 2 GND 7
03P9339
3 3 OP_VIDEO_1 8
4 4
PWR PCB
5 5 J618(NH)
RW-4864,φ9.5
MARINE RADAR/ARPA
6 6 GND 1 SUB DISPLAY2

OP_HD_2 2
船舶用レーダー/ARPA
10 10 GND 3
(SEMI-LOG)
OP_BP_2 4
INTERCONNECTION DIAGRAM
GND 5
OP_TRIG_2 6
GND 7
OP_VIDEO_2 8
FAR-2117/2127/2817/2827 (DC SET)
S-2
&
%
$
#

ᵈ⸥

8#% &2;% 47
Ǿ*\ 6$
+8US
8#%Ǿ &2;%; 8#%A*
଻⼔ࠕ࡯ࠬ
2'

*\ 8#%A%
0%
2'
ⓨਛ✢ㇱ
᳖⚿㒐ᱛ↪
଻⼔㨻㨺㩇
8#% &2;% (14 &'+%'4
+8US
ࠝࡊ࡚ࠪࡦ‫ޕ‬
ㅧ⦁ᚲᚻ㈩‫ޕ‬
45$
Ǿ*\

#06'00# 70+6
࠻࡜ࡦࠬ
,
:* ,
47
,
64#05(14/'4
6$
2 )%A.'& 6:A*8 49OǾ 6$
49
&2;%
$1#4&
8#% * )%A*1.& 0% ࠴ࡖ $40 6:A*8
Ǿ*\ %
2 ,
8* )%A72 , 0%
);41A4 )%A&190 8A2.75 ࠳ࠗ
ᄥ 14)=$? 8A2.75
)%A8 ࠠ
ᄥ
, );41A4 8A/+075 ;'.=$? 8A/+075
2#
/2;% ࠴ࡖ $40 ࠕࠝ
ᄥ
);41%1/2#55 0% )%A8 /1614
$.7=$? /1614

);41 %108'46'4
ࠕࠞ 4'& ,
8* ,
0*
2 , /1614
ࡂࠗ
ᄥ )4;=$? /1614

࠳ࠗ 14) );41A5 &#6#* ࠴ࡖ $40 #&A&#6#* /1614
㩛㩡㩅㩁
ᄥ 22.=$? /1614

2
ࠠ ;'. );41A5 &#6#% ࠕࠞ 4'& #&A&#6#% /1614
ࠪࡠ
ᄥ 9*6=$? /1614

⦁ౝ㈩㔚⋚ߢߪ#ߩࡉ࡟࡯ࠞࠍ૶↪‫ޕ‬
㩚㩎㩨㩢 )40 );41A5 5*+(6* ࠳ࠗ 14) #&A%.-* 527A4(A&# ࠕࠞ 4'& 527A4(A&A#
2
2/
ࠕࠝ $.7 );41A6 5*+(6% ࠠ ;'. #&A%.-% 527A4(A&$ 㩚㩎㩨㩢 )40 527A4(A&A$

㩛㩡㩅㩁 22. );41A() () 4(A527A&# ࠢࡠ $.- 4(A527A&A#

2 4(A527A&$ ࠪࡠ 9*6 4(A527A&A$
㩚㩎㩨㩢
ᄥ
5) )40=$? 5)
#& %108'46'4 66;%5 )0& ࠕࠞ
ᄥ 4'&=$? )0&
2'4(14/#0%' /10+614
, 6$
ᦨ㐳 O
ᑧ㐳ߔࠆߣ߈ߪធ⛯▫4,$߇ᔅⷐ ‫ޕ‬
+(A8+&'1 +(A8+&'1
ࡄࡈࠜ࡯ࡑࡦࠬࡕ࠾࠲࡯
଻⼔ࠕ࡯ࠬ↪ࠤ࡯ࡉ࡞ߪ✛㧛㤛ߩ⛘✼✢ࠍ૶↪ߩߎߣ‫ޕ‬
2
)0& )0&

6$ $1#4&
੤ᵹߪਔᭂಾࠅࡉ࡟࡯ࠞ㧔ㅧ⦁ᚲᚻ㈩㧕ࠍ⚻↱ߔࠆߎߣ‫ޕ‬
, , , ,
4)$ ':6 /10+614 8)# %#$.' 4A8+&'1 4A8+&'1 4 ว⸘㧦Oએਅ 616#. 72 61 O
)A8+&'1 )0& )0&
$A8+&'1 )A8+&'1 ) :*292 :*292#
0% )0& )0& OǾ
OǾ

0% $A8+&'1 $
5.$(40#
)0& )0& )0& , ,, ,, ,
016'5
%1#:
ǡ㨤 )0& *A5;0% *5
8&4 -';A6:&$ -';A6:&$ -';A6:&$ -';A6:&A$
2#
&8+4)$ᄌ឵ၮ᧼
)0& )0& )0& -';A6:&# -';A6:&# -';A6:&# -';A6:&A#
&57$$0%
0% 8A5;0% 85 -';A4:&$ -';A4:&$ -';A4:&$ -';A4:&A$
126+10
%108'46'4
)0& )0& )0& -';A4:&# -';A4:&# -';A4:&# -';A4:&A#
4)$ $7(('4 2%$

4)$ 㩔㩨㨹㩖㨱 ၮ᧼
$0% %100'%614
$0%㩄㩒㩂㩊㩄㩧㩔㩨㨺㩊
)0& 8%% 294A59 294A59 294A59 294A59
0% )0& )0& )0& )0& )0&
&8+4)$ %108'45+10 $1#4&

*A5;0% 8 8 8 8 8
;A5;0% )0& )0& )0& )0&
5*+2;#4& 5722.;
0% 5;5A(#+.* 5;5A(#+.* 0% 0%
0%
0%
)0&
)0&
8
8
8
)0&
8%%
,
,
5;5A(#+.% 5;5A(#+.% 0% 0%

&8+4)$
,,
4)$㩕㩨㩍㩨㨿㩄㩧㩔㩨㨺㩊

4%7
ᠲ૞ㇱ
%10641. 70+6
4)$ 8+&'1 %108'4614

5;5A(#+.*
, , 5;5A(#+.%
ᠲ૞ㇱ
࠴ࡖ $40 8 5;5A#%-* 5;5A#%-*

ࠕࠞ 4'& )0& 5;5A#%-% 5;5A#%-%
࠳ࠗ 14) 8
+8US
4%7
ࠠ ;'. )0&
%10641. 70+6
2'
଻⼔ࠕ࡯ࠬ
㩚㩎㩨㩢 )40 8 ,
0%
75' )40;'. 9+4' (14 2416'%6+8' '#46*

4:&
6:&
75' # $4'#-'4 +0 5*+2 5 /#+05 59+6%* $1:

0%
45% %#$.'
)0& 2%

0%
45%
0%
&8+& /10+614 0%

ᄖㇱࡕ࠾࠲࡯ , 0%
&8+ %#$.' &8+6:A0
':6 /10+614 &8+6:A2 ,
*&)#
66;%53 *&) 5'0514
#A)0& 2
/#: O
,70%6+10 $1: 4,$ +5 4'37+4'& (14 ':6'05+10
0% *&)$
+'%
0% *&)A)0&
0%

0% ,
0#8#
66;%5
0% 0#8+)#614
2#55 6*' #% .+0' 6*417)* # &17$.'%106#%6 $4'#-'4

5*+2;#4& 5722.;
2
&8+6:A0 0#8$
+'%
&8+6:A2 0%
೙ᓮㇱ
427
#A)0&

0% ,
.1)#
66;%5
0% 52''& .1)
2
8%% .1)$
+'%
)0& 0%
241%'5514 70+6
0%

&8+6:&A0 ,
#42##
66;%5
&8+6:&A2 '%&+5
2
#A)0& #42#$
+'%
0% 0%
0%

#A)0& ,
64-A6&#
66;%5
&8+6:%A2
2 64#%-A%10641.
&8+6:%A0 64-A6&$
64-A4&#
+'%
2
64-A4&$
&8+& /10+614 )0&

ᄖㇱࡕ࠾࠲࡯ ,
&8+ %#$.' 5#/' #5 #81$' ,
':6 /10+614 458A6&#
458A6&$ 016 75'&
)0&
458A6&#
458A6&$
5%#.'
&4#90 )0&
&9)0Q
%*'%-'&
#22418'&
, /,#52( /,#52(OǾ ,
8

8 ࠪࡠ 9*6 ,
)0& #+5A6&#
66;%5
)0& ࠢࡠ $.- #+5
%7
2
() #+5A6&$

+'%
,WP
#+5A4&#
0'6914- 2
, /25% #+5A4&$
2'26:$.OǾ
/#55
6:2 6:2 #+5A)0&
2
6:0 6:0
,

4:2 4:2
;*CVCK
66;%5
㒐᳓ဳ㩀㨺㩎㩨㨼㩧㩊㨺㩖㨴㨼㩇
0% 0% #.#4/A #.#4/ 5;56'/

.#0
2 2
/'/14; %#4& +( 70+6
%% 0
0% 0% #.#4/A
'/+;15*+
6#-#*#5*+6

MI
4:0 4:0 #.#4/A

2

0% 0% #.#4/A

0% 0% #.#4/A
2
+8US
#.#4/A
.#0 %#$.'
%#6 14 12'4#614A(+60'55A
2
/25% (4(62%%;OǾ 12'4#614A(+60'55A
6:2 ࠪࡠ㩚㩎㩨㩢 9*6)40 ':6A#./A#%-A0
2 2
6:0 ࡒ࠼࡝ )40 )0&
4:2 ࠪࡠ࠳ࠗ 9*614) 5;5A(#+.*
2
0% ࠕࠝ $.7 5;5A(#+.%
2
0% ࠪࡠࠕࠝ 9*6$.7
࠳ࠗ 14) ,
0*
㩇㨼㨹㩋㩧㩂㩨㩔㩖㩨
4:0 49Ǿ
ࠪࡠ࠴ࡖ 9*6$40 )0&

59+6%*+0) *7$
0% /#56'4 4#&#4
0% ࠴ࡖ $40 12A*&A+0
)0&
*7$
21465
042(885

#% 8#% 12A$2A+0
#% O Ǿ Ǿ*\ )0&
)0& 12A64+)A+0
)0&
0#/'
6;2'
ฬ ⒓
12A8+&'1A+0
,
0*
49Ǿ
)0&
଻⼔ࠕ࡯ࠬ 2'
57$ &+52.#;
12A*&A
+8US
)0&

(7...1)

12A$2A
)0&
12A64+)A
⋧੕⚿✢࿑
)0&
12A8+&'1A
,
0*
49Ǿ
)0& 57$ &+52.#;
/#4+0' 4#&#4#42#
12A*&A
)0&

5'/+.1)
⦁⥾↪࡟࡯࠳࡯#42#
12A$2A
)0&
12A64+)A
+06'4%100'%6+10 &+#)4#/
)0&
(#4$$
#% 5'6
12A8+&'1A
S-3
&
%
$
#

ᵈ⸥

8#% &2;% 47
Ǿ*\ 6$
+8US
8#%Ǿ &2;%; 8#%*
଻⼔ࠕ࡯ࠬ
2'

*\ 8#%%
0%
2'
ⓨਛ✢ㇱ
᳖⚿㒐ᱛ↪
଻⼔㨻㨺㩇
(14 &'+%'4
+8US
8#% &2;%
ࠝࡊ࡚ࠪࡦ‫ޕ‬
ㅧ⦁ᚲᚻ㈩‫ޕ‬
ᢛᵹེ
45$

#06'00# 70+6
Ǿ*\
4'%6+(+'4
,
:* ,
47
,
6$
2 )%A.'& 6:A*8 49OǾ 6$
49
&2;%
$1#4&
8&%
)%A*1.& 0% ࠴ࡖ $40 6:A*8

2 ,
8* )%A72 , 0%
);41A4 )%A&190 8A2.75 ࠳ࠗ
ᄥ 14)=$? 8A2.75
)%A8 ࠠ
ᄥ
, );41A4 8A/+075 ;'.=$? 8A/+075
2#
/2;% ࠴ࡖ $40 ࠕࠝ
ᄥ
);41%1/2#55 0% )%A8 /1614
$.7=$? /1614

);41 %108'46'4
ࠕࠞ 4'& ,
8* ,
0*
2 , /1614
ࡂࠗ
ᄥ )4;=$? /1614

࠳ࠗ 14) );41A5 &#6#* ࠴ࡖ $40 #&A&#6#* /1614
㩛㩡㩅㩁
ᄥ 22.=$? /1614

2
ࠠ ;'. );41A5 &#6#% ࠕࠞ 4'& #&A&#6#% /1614
ࠪࡠ
ᄥ 9*6=$? /1614

⦁ౝ㈩㔚⋚ߢߪ#ߩࡉ࡟࡯ࠞࠍ૶↪‫ޕ‬
㩚㩎㩨㩢 )40 );41A5 5*+(6* ࠳ࠗ 14) #&A%.-* 527A4(A&# ࠕࠞ 4'& 527A4(A&#
2
2/
ࠕࠝ $.7 );41A6 5*+(6% ࠠ ;'. #&A%.-% 527A4(A&$ 㩚㩎㩨㩢 )40 527A4(A&$

㩛㩡㩅㩁 22. );41A() () 4(A527A&# ࠢࡠ $.- 4(A527A&#

2 4(A527A&$ ࠪࡠ 9*6 4(A527A&$
㩚㩎㩨㩢
ᄥ
5) )40=$? 5)
#& %108'46'4 66;%5 )0& ࠕࠞ
ᄥ 4'&=$? )0&
2'4(14/#0%' /10+614
, 6$
ᦨ㐳 O
ᑧ㐳ߔࠆߣ߈ߪធ⛯▫4,$߇ᔅⷐ ‫ޕ‬
+(A8+&'1 +(A8+&'1
ࡄࡈࠜ࡯ࡑࡦࠬࡕ࠾࠲࡯
଻⼔ࠕ࡯ࠬ↪ࠤ࡯ࡉ࡞ߪ✛㧛㤛ߩ⛘✼✢ࠍ૶↪ߩߎߣ‫ޕ‬
2
)0& )0&

6$ $1#4&
, , , ,
4)$ ':6 /10+614 8)# %#$.' 4A8+&'1 4A8+&'1 4 ว⸘㧦Oએਅ 616#. 72 61 O
)A8+&'1 )0& )0&
$A8+&'1 )A8+&'1 ) :*292 :*292#
0% )0& )0& OǾ
OǾ

0% $A8+&'1 $
5.$(40#
)0& )0& )0& , ,, ,, ,
016'5
%1#:
ǡ㨤 )0& *A5;0% *5
8&4 -';A6:&$ -';A6:&$ -';A6:&$ -';A6:&$
2#
&8+4)$ᄌ឵ၮ᧼
)0& )0& )0& -';A6:&# -';A6:&# -';A6:&# -';A6:&#
&57$$0%
0% 8A5;0% 85 -';A4:&$ -';A4:&$ -';A4:&$ -';A4:&$
126+10
%108'46'4
)0& )0& )0& -';A4:&# -';A4:&# -';A4:&# -';A4:&#
4)$ $7(('4 2%$

4)$ 㩔㩨㨹㩖㨱 ၮ᧼
$0% %100'%614
$0%㩄㩒㩂㩊㩄㩧㩔㩨㨺㩊
)0& 8%% 294A59 294A59 294A59 294A59
0% )0& )0& )0& )0& )0&
&8+4)$ %108'45+10 $1#4&

*A5;0% 8 8 8 8 8
;A5;0% )0& )0& )0& )0&
5*+2;#4& 5722.;
0% 5;5A(#+.* 5;5A(#+.* 0% 0%
0%
0%
)0&
)0&
8
8
8
)0&
8%%
,
,
5;5A(#+.% 5;5A(#+.% 0% 0%

&8+4)$
,,
4)$㩕㩨㩍㩨㨿㩄㩧㩔㩨㨺㩊

4%7
ᠲ૞ㇱ
%10641. 70+6
4)$ 8+&'1 %108'4614

5;5A(#+.*
, , 5;5A(#+.%
ᠲ૞ㇱ
࠴ࡖ $40 8 5;5A#%-* 5;5A#%-*

4%7
ࠕࠞ 4'& )0& 5;5A#%-% 5;5A#%-%

%10641. 70+6
࠳ࠗ 14) 8
+8US
)0&
ࠠ ;'. )0&
㩚㩎㩨㩢 )40 8 ,
0%
75' )40;'. 9+4' (14 2416'%6+8' '#46*

4:&
6:&
75' # $4'#-'4 +0 5*+2 5 /#+05 59+6%* $1:

0%
45% %#$.'
)0& 2%

0%
45%
0%
&8+& /10+614 0%

ᄖㇱࡕ࠾࠲࡯ , 0%
&8+ %#$.' &8+6:A0
':6 /10+614 &8+6:A2 ,
*&)#
66;%53 *&) 5'0514
#A)0& 2
/#: O
,70%6+10 $1: 4,$ +5 4'37+4'& (14 ':6'05+10
0% *&)$
+'%
0% *&)A)0&
0%

0% ,
0#8#
66;%5
0% 0#8+)#614
2
&8+6:A0 0#8$
+'%
&8+6:A2 0%
೙ᓮㇱ
427
#A)0&

0% ,
.1)#
66;%5
0% 52''& .1)
2
8%% .1)$
+'%
)0& 0%
241%'5514 70+6
0%

&8+6:&A0 ,
#42##
66;%5
&8+6:&A2 '%&+5
2
#A)0& #42#$
+'%
0% 0%
0%

#A)0& ,
64-A6&#
66;%5
&8+6:%A2
2 64#%-A%10641.
&8+6:%A0 64-A6&$
64-A4&#
+'%
2
64-A4&$
&8+& /10+614 )0&

ᄖㇱࡕ࠾࠲࡯ ,
&8+ %#$.' 5#/' #5 #81$' ,
':6 /10+614 458A6&#
458A6&$ 016 75'&
)0&
458A6&#
458A6&$
5%#.'
&4#90 )0&
&9)0Q
%*'%-'&
#22418'&
, /,#52( /,#52(OǾ ,
8

8 ࠪࡠ 9*6 ,
)0& #+5A6&#
66;%5
)0& ࠢࡠ $.- #+5
%7
2
() #+5A6&$

+'%
,WP
#+5A4&#
0'6914- 2
, /25% #+5A4&$
2'26:$.OǾ
/#55
6:2 6:2 #+5A)0&
2
6:0 6:0
,

4:2 4:2
;*CVCK
66;%5
㒐᳓ဳ㩀㨺㩎㩨㨼㩧㩊㨺㩖㨴㨼㩇
0% 0% #.#4/A #.#4/ 5;56'/

.#0
2 2
/'/14; %#4& +( 70+6
%% /
0% 0% #.#4/A
'/+;15*+
6#-#*#5*+6

MI
4:0 4:0 #.#4/A

2

0% 0% #.#4/A

0% 0% #.#4/A
2
+8US
#.#4/A
.#0 %#$.'
%#6 14 12'4#614A(+60'55A
2
/25% (4(62%%;OǾ 12'4#614A(+60'55A
6:2 ࠪࡠ㩚㩎㩨㩢 9*6)40 ':6A#./A#%-A0
2 2
6:0 ࡒ࠼࡝ )40 )0&
4:2 ࠪࡠ࠳ࠗ 9*614) 5;5A(#+.*
2
0% ࠕࠝ $.7 5;5A(#+.%
2
0% ࠪࡠࠕࠝ 9*6$.7
࠳ࠗ 14) ,
0*
㩇㨼㨹㩋㩧㩂㩨㩔㩖㩨
4:0 49Ǿ
ࠪࡠ࠴ࡖ 9*6$40 )0&

59+6%*+0) *7$
0% /#56'4 4#&#4
0% ࠴ࡖ $40 12A*&A+0
)0&
*7$
21465
042(885

#% 8#% 12A$2A+0
#% O Ǿ Ǿ*\ )0&
)0& 12A64+)A+0
)0&
0#/'
6;2'
ฬ ⒓
12A8+&'1A+0
,
0*
49Ǿ
)0&
଻⼔ࠕ࡯ࠬ 2'
57$ &+52.#;
12A*&A
+8US
)0&

(7...1)

12A$2A
)0&
12A64+)A
⋧੕⚿✢࿑
)0&
12A8+&'1A
,
0*
49Ǿ
)0& 57$ &+52.#;
/#4+0' 4#&#4#42#
12A*&A
)0&

5'/+.1)
⦁⥾↪࡟࡯࠳࡯#42#
12A$2A
)0&
12A64+)A
+06'4%100'%6+10 &+#)4#/
)0&
(#4$$
&% 5'6
12A8+&'1A
S-4

FAR2 XX 7 Ime

Uploaded by

Copyright:

Available Formats

FAR2 XX 7 Ime

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FAR2 XX 7 Ime

Uploaded by

Copyright:

Available Formats

Comply with MSC.

3. SETTING AND ADJUSTMENT .... 3-1

・FURUNO Authorized Distributor/Dealer

All rights reserved. Printed in Japan A : JAN . 2004

Indicates a potentially hazardous situation which, if not avoided,

Indicates a potentially hazardous situation which, if not avoided,

Indicates a potentially hazardous situation which, if not avoided,

Warning, Caution Prohibitive Action Mandatory Action

Construct a suitable service platform Monitor Unit

Attach securely protective

About the category sticker

ANTENNA UNIT MU-201CR,

MEMORY CARD AC spec

Those items contain organic solvents that

1.1 Antenna Unit

less than 500 m or twice the ship’s length

a, b, c: less than 5 respectively

Assembling the antenna unit

10 mm O-ring Waveguide cap

Hole for Hole for

Coating the waveguide flange with anticorrosive sealant

Injury may result if the guide pins loosen

Fastening the radiator to the radiator bracket

Lifting NO! NO!

Antenna unit, front view

Ground wire Hex bolt

Hex bolt welded to

How to mount the antenna unit

1.2 Monitor Unit

Note: FAR-2117-BB/2127-BB have no monitor unit. Prepare a suitable monitor locally.

490 506±1 4-φ8

Monitor unit MU-201CR

570±1 4-φ8 FIXING HOLES

Monitor unit MU-231CR

Flush mounting of monitor unit

Attaching panel hook and panel cover

M12 bolts for fixing

Hanger stay Hanger (R)

To remove this, insert fingernail in groove.

Hex head bolt

1.3 Control Unit

Fixing with KB fixing plate

KB fixing plate Cushion

Side view for RCU-014/015/016

4-M4 (Fixing holes)

Control Unit RCU-014

110±1 4-M4 (Fixing holes)

Name: Flush mount kit

1. Prepare a cutout in the mounting location as shown in the figure below.

For RCU-014 For RCU-015 and RCU-016

2. Set the control unit to the cutout.

To connect RCU-016 in series with RCU-014

1. Pass the cable derived from RCU-016.

2. Connect the connector

To change the cable entry

Screw Bottom of the unit

2. Pull out the cable.

3. Pass the cable from this hole. Cable clamp

J522: If you connect RCU-016 in series with RCU-015, plug in here.