Chapter 2.

Location of Parts
2.1 Processor Unit: RPU-013

2.1 Processor Unit: RPU-013

DVI-D Connectors for
LCD Display Unit
(Both are identical.)

F1
100 VAC: 10 A (125 V)
220 VAC: 5 A (250 V)
LAN Port (RJ45) for 24 VDC: 20 A (125 V)
FAR-21X7/28X7,
Network Hub (HUB-100),
CARD I/F (CU-200) or
INS

Fig. 2.1.1 Radar Processor Unit, Bottom View

Fan (blowing air in)

MMS-06C24DS/24VDC 0.09A

Fig. 2.1.2 Processor Unit, Top View

2-1
 2.1 Processor Unit: RPU-013

Fig. 2.1.3 Processor Unit with hinged cover opened

HV9017 Board
HV-9017A: 12 kW (330 V)
HV-9017B: 25 kW (550 V)
SPU Board
03P9337

PRW Board
AC Power Supply:
03P9339A/B/C/D
DC Power Supply:
03P9338A/B/C/D NET Board
NET100 基板
* 03P9338A/B: 12V SPEC 03P9332
03P9332
(No shipping.)

FIL Board (Line Filter)

AC SPEC: 03P9341
DC SPEC: 03P9352

Fig. 2.1.4 Processor Unit with Shield Covers Removed

2-2
 2.1 Processor Unit: RPU-013

LAN Port
(100 BASE-T)

Digital Video Output

(DVI-D)

GND Terminal

Power Supply Terminal

Fig. 2.1.5 Processor Unit, bottom chassis

DVI-RGB I/F Board

DVI-RGB I/F Board

RGB BUFF Board Stopper

(03P9229B)

Hinge
** Possible to separate
between bottom and
GC-10 Board upper chassis.
(64P1106A, Optional)

Terminal Board
GYRO Input Terminal
(03P9342)
(Optional)

Fig. 2.1.6 Processor Unit, bottom chassis

2-3
 2.1 Processor Unit: RPU-013

S1 (Selection of monitor type)

Model 1 2 3 4
FAR-21x7 (MU-201CR) OFF OFF
FAR-28x7 (MU-231CR) ON OFF OFF
FAR-21x7-BB OFF ON

CR4 (Blinks every second.)

CR8
(Blinks every Mounting part
0.5 second.) MAIN CPU of NET-100.
(U21)

ARPA CPU
(U74)

DVI-D J204
S2
(Reset SW)

DVI-D J205

DRW CPU
(U19)

CR2/CR3 (Always ON)

TP58 (2Vp-p)
R401 CR5 (Blinks every second.)
(Used to adjust OP Video
CR Check for
IN level, 2Vp-p at TP58)
CR2 VCC (+5 V)
CR3 3.2 V
CR4 MAIN CPU (U21)
CR5 DRW CPU (U19)
Note: CR8 ARPA CPU (U74)
See page.5-2 for SPU Ver-22.

Fig. 2.1.7 SPU Board, 03P9337 Ver.11

2-4
 2.1 Processor Unit: RPU-013

100BASE-T
(RJ-45)

CR1 (LED-B)
(Blinks when LAN port is used.)

CR2 (LED-A)
(Lights when data flows through LAN port.) ** This board is also used in CU-200.

Fig. 2.1.8 NET-100 Board, 03P9332

2-5
 2.1 Processor Unit: RPU-013

TP1: Main Inverter Output Voltage (34.7 to 35.3 VDC)

TP2: SW Reg. Common Line
TP3: Sub Inverter SW Freq. (42.75 to 47.25 kHz)
TP4: Main Inverter SW Freq. (42.75 to 47.25 kHz)

VR1 (Main Inverter Output Adj.)

CR23 (GRN)
CR21 (RED)

JP1 (COM/300 V/ 500 V)

Suffix mark

A SPEC (12 kW) B SPEC (More than 25 kW)

JP1 COM-300 V COM-500 V JP2 (COM/300 V/330 V)
JP2 COM-330 V COM-330 V

Fig. 2.1.9 HV-9017 A/B Board

100 VAC: 10 A (125 V)

220 VAC: 5 A (250 V) Fuse 20 A

Fig. 2.1.10 AC FIL Board, 03P9341 Fig.2.1.11 DC FIL Board, 03P9352

2-6
 2.1 Processor Unit: RPU-013

Setting of Antenna Rotation Speed

24 rpm: 144 Hz at TP17 with R168, J161 and J162 opened
42 rpm: 252 Hz at TPI7 with R168, J161 and J162 shorted
JP161 (42 rpm)
JP162 (42 rpm) TP13
R168 (RT) TP17 (BP)
TP14 (32 V)
TP15
R106
J105 J106 TP12 (14 V)
TP16 (5 V)

TP11 (12 V)

TP18
TP19
J104
CR63 (MTR)
TP9
CR64 (RF)

TP2 CR65 (Tx-HV)

(PR0V) J103
R48 (45kHz)
TP-1 (S-5 V)
CR23 (IN-ER)
R88 TP3 (PR12 V)

TP4（PR5 V）
TP5 (PR5 V)
TP7

R21 (OVER)
TP6

J101

CR23: Input Over/Low-Voltage

CR63: ANT Motor Overcurrent
J108
CR64: ANT24 V Overcurrent
220 VAC: No jumper
CR65: TX-HV Overcurrent
100 VAC: Jumpers between 1-2, 4-7 and 5-8.
Board Name Power Supply Antenna speed
03P9339A 100 VAC 24 rpm
03P9339B 100 VAC 42 rpm
03P9339C 220 VAC 24 rpm
03P9339D 220 VAC 42 rpm

Fig. 2.1.12 AC PWR Board, 03P9339A/B/C/D

2-7
 2.1 Processor Unit: RPU-013

Setting of Antenna Rotation

24 rpm: 144 Hz at TP17 with R168, J161 and J162 opened
JP161 (42 rpm) 42 rpm: 252 Hz at TP17 with R168, J161 and J162 shorted
JP162 (42 rpm)

TP17 (B.P)
R168
J105 J106

R106

TP19

TP14（32 V）
TP18
J104
CR63 (MTR)
TP9
CR64 (RF)

CR65 (Tx_HV)
TP8 J103
R88 (12 V) TP1 (S_5 V)
CR23 (1N-ER)

TP13 R26 (45 kHz)

TP3 (PR12 V)
TP7
TP10 (GND)

TP12 (-14 V)

J101

TP6 TP2

TP11 (12 V) CR23: Input Over/Low-Voltage

CR63: ANT Motor Overcurrent
CR64: ANT24V Overcurrent
Board Name Power Supply Antenna Speed
03P9338A 12-24 VDC 24 rpm
CR65: TX-HV Overcurrent
03P9338B 12-24 VDC 42 rpm
03P9338C 24 VDC 24 rpm
03P9338D 24 VDC 42 rpm

Fig. 2.1.13 DC PWR Board, 03P9338A/B/C/D

2-8
 2.1 Processor Unit: RPU-013

J654 (SPU) J652 (PWR)

J651 (HV)
12 kW: 310-350 V
25 kW: 520-580 V
PSU PSU
J613 (SCANNER)

J601 (RS-232C) J614 (CARD I/F)

(9P D-SUB)
J615 (OPTION)

J610 (SCANNER) J616 (From Master)

J617 (To Slave 1)

J602 (KEY)

J604 (PSU)
J618 (To Slave 2)
J606 (HEADING)
(IEC-61162-2) J656

J619 (ECDIS)
J603 (GC-10)

J611 (AIS)

J606 (NAVIGATOR)
J655

J622 (KEY)

J607 (LOG) J620 (TRACK CONTROL)

J621 (SERIAL I/F)

J608 (AD CONVERTER) J612 (EXT ALARM)

J656: HEADING (IEC-61162-2)

Selection of 110-ohm terminator on HDG line. (Default: Jumper between 1 and 2; terminated)
J655: AIS (IEC-61162-2)
Selection of 110-ohm terminator in AIS line. (Default: Jumper between 1 and 2; terminated)

Fig. 2.1.14 TB Board, 03P9342

2-9
 2.1 Processor Unit: RPU-013

a.

b.

L=20 mm 231-131
L=19 mm

734-230

c.

Fig. 2.1.15 WAGO Connector and Terminal Opener

2-10
 2.2 Scanner Unit

2.2 Scanner Unit

2.2.1 FAR-2xx7

Performance Monitor (PM-31)

Antenna

Fig. 2.2.1 Scanner Unit (RSB-096 with PM-31)

2-11
 2.2 Scanner Unit

FAN (24 VDC)

Internal heat is agitated.

J921 (TX_HV)

RTR-079 (25 kW)

VR1 (Power Adj.)

This hole is used to access VR1 on MD board
(03P9244) for magnetron current adjustment at factory.

Fig. 2.2.2 Scanner Unit with Cover Removed (1)

IF Board (03P9335A)

PM-31 Connection

J921 (HV)

Fig. 2.2.3 Scanner Unit with Cover Removed (2)

2-12
 2.2 Scanner Unit

O-Ring Rotary Joint

Guide Pin Hole Guide Pin Hole

Fig. 2.2.4 Antenna Bracket

PM-31 Antenna
(03P9361)

PM-31/B3RX1626

Fig. 2.2.5 Performance Monitor, PM-31

2-13
 2.2 Scanner Unit

Motor Brush Holder (x2)

Motor Brush (MG120-5x6x11)

Wear Line
(When bush wears to white line, it must be replaced.)

Motor Type Antenna Speed Scanner Unit Fig. 2.2.6 Antenna Motor
D8G-516 24 rpm RSB-096
D8G-571 42 rpm RSB-097

Magnet for Heading Lead Switch

Antenna Turning Gear

Gear Retainer

Rotary Joint

Fig. 2.2.7 Antenna Motor Gear

2-14
 2.2 Scanner Unit

Heading Lead SW

J916
(HD/B.P) B.P GEN Board (03P9347)

IF AMP Board OUTPUT

Terminal
J918 (FAN 24V)
RT TB Board (03P9349)
J914 (ANT 24V)
J915 (TX_HV)
TB801 TB803

J917
3 Units are used.
TB804 (FAR-2837SW: RTR-082)
(Antenna Motor Power Supply)

Fig. 2.2.8 Antenna Terminal Board

B.P GEN Board (03P9347)

Antenna Drive Gear

Fig. 2.2.9 Antenna Drive Gear

2-15
 2.2 Scanner Unit

RFC Board (03P9346A) Circulator

Diode Limiter

IF Board (03P9335A) PWR (RF) Board

- 03P9348A: 12 kW
- 03P9348B: 25 kW

MIC (RU-9601)

Fig. 2.2.10a RTR-079 (25 kW)

Fig. 2.2.10 b RTR-079 (25 kW)

2-16
 2.2 Scanner Unit

IFAMP OUT
（J823） J3
1. Mag.Cur
3. GND

CR9
(RTR-078 and -079 use the board.) (Blinks every second,
CPU (U19) operations)
Fig. 2.2.11 RFC Board, 03P9346A

Mag. Heater Volt ADJ. (J833-#11)

R28 (Maｇ. H)
マグネトロン
MG5439 R32 (Mag. L)

J833

R62 (ADJ)
(MIC TUNNIING,
マグネトロン +32 V at J833#6)
MG4010 or MAF1425B

03P9348A: 12 kW
03P9348B: 25 kW
03P9348C: 30 kW (S-band)
R57 (-12V at J833-#1)

Fig. 2.2.12 PWR(RF) Board, 03P9348

2-17
 2.2 Scanner Unit

J823 (IF Output) J824 (IF Input)

Fig. 2.2.13 IF AMP Board, 03P9335A

60 MHz IF Output

VR1 (Power)
Used to adjust magnetron
current at factory.

03P9244A: X band 10 kW
03P9244B: X band 25 kW
03P9244E: S band 30 kW

Fig. 2.2.14 MD Board, 03P9244A/B

2-18
 2.2 Scanner Unit

MD Board
(03P9244B)

Pulse Transformer
(RT9023)
Magnetron
(MG5436)

Fig. 2.2.15 RTR-079 (25 kW)

MD Board
(03P9244A)

Magnetron
(MG4010 or MAF1425B) Pulse Transformer
(RT9025)

Fig. 2.2.16 RTR-078 (10 kW)

2-19
 2.2 Scanner Unit

2.2.2 FAR-2827W scanner unit

TB Board (03P9349)
Waveguide Joint

DC Motor (D8G-516, 24 rpm)

Cable Grand

De-Icer

Fig. 2.2.17 (a) RSB-103

Heading Lead SW
Drive Gear

Scanner Turning Gear B.P GEN Board (03P9347)

TB804
(Antenna Motor Power Supply)

Fig. 2.2.17(b) RSB-103

2-20
 2.2 Scanner Unit

Fig. 2.2.18 (a) RSB-103 Waveguide

Magnet for Heading Lead Switch

Gear Retainer

Waveguide

Fig. 2.2.18 (b) RSB-103 Waveguide

2-21
 2.2 Scanner Unit

Waveguide Joint

RF Unit

TB Board (03P9349A)

Cable Entry

Fig. 2.2.19 RTR-081 (FAR-2827W, 25 kW)

Added 2P connector:
IF AMP Board
Ver.33A and after
(03P9335A) RFC Board (03P9346A)

MIC: RU-9601
or RU-9603 TR Limiter

PWR (RF) Board (03P9348B)

Fig. 2.2.20 Removed from RF Unit

2-22
 2.2 Scanner Unit

Pulse Transformer (RT9023) Magnetron (MG5436) Magnetron Cooling Fan

MD Board
(03P9244B)

Fig. 2.2.21 (a) RTR-081 RF Unit with Shield Cover Removed (1)

Fig. 2.2.21 (b) RTR-081 RF Unit with Shield Cover Removed (2)

2-23
 2.2 Scanner Unit

2.2.3 FAR-2837S scanner unit

Performance Monitor Antenna

Antenna Motor (SW)

Cable Gland

Fig. 2.2.22 RSB-098

IF AMP Board
(03P9335B) with
shield cover removed

MIC (RU-9427)

TB Board (03P9349A)
Antenna Motor
(RM-7398)

Fig. 2.2.23 RSB-098 with Cover Removed

2-24
 2.2 Scanner Unit

TB Board (03P9349A)

Fig. 2.2.24 RSB-098 with TB Board Removed

Performance Monitor Antenna

PM-51

Diode Limiter

Fig. 2.2.25 RSB-098 with MIC removed

2-25
 2.2 Scanner Unit

RFC Board (03P9346-33A)

Antenna Motor Power

Supply Terminal

Fig. 2.2.26 RSB-098 with Cover Removed

MSS-7497 Board

PWR(RF) Board (03P9348C)

Fig. 2.2.27 RSB-098 with RFC Board Chassis Removed

2-26
 2.2 Scanner Unit

Magnetron (MG5223F)
MD Board (03P9244E)

Pulse Transformer (RT9273)

Fig. 2.2.28 RSB-098 with Shield Cover Removed

Magnetron Cooling Fan

Fig. 2.2.29 RSB-098 with Magnetron Removed

2-27
 2.2 Scanner Unit

Antenna Motor SW

Circulator

Fig. 2.2.30 RSB-098 with Pulse Mounting Chassis Removed Transformer

And MD Board

B.P GEN Board (03P9347)

Fig. 2.2.31 RSB-098, Rotary Joint

2-28
 2.2 Scanner Unit

Antenna Motor Mounting Plate MD Board

Antenna Motor

(MSS-7497 Board Removed)

TB Board
Fig. 2.2.32 RSB-098 Antenna Motor

2-29
 2.2 Scanner Unit

2.2.4 FAR-2827SW scanner unit

Performance Monitor Antenna

Performance Monitor (PM-51)

MSS-7497 Board
TB for Antenna Motor Power Supply

Fig. 2.2.33 RSB-104 with Cover Removed

Antenna Switch

Waveguide Flange

Fig. 2.2.34 RSB-104 with Cover Removed

2-30
 2.2 Scanner Unit

Antenna Motor (RM-7398) B.P GEN Board (03P9347)

Fig. 2.2.35 RSB-104 with MSS-7497 Board Removed

Performance Monitor (PM-51)

Antenna Motor
Mounting Plate
TB Board (03P9349A)

Fig. 2.2.36 RSB-104 with Cover Removed

2-31
 2.2 Scanner Unit

Cable Clamp Waveguide Joint

Fig. 2.2.37 RTR-082（FAR-2837SW: 30 kW）

MD Board (03P9244E)

PWR (RF) Board

(03P9348C)
Magnetron (MG5223F)
RFC Board (03P9346-33A)

TB Board (03P9349A)
IF AMP Board (03P9335B)
with a shield cover removed

Use this hole to adjust breaker current.

Fig. 2.2.38 RTR-082 with Cover Removed

2-32
 2.2 Scanner Unit

MD Board (03P9244E)

図 2.2.37 RTR-0828 マグネトロン、TB 基板取り外し

PWR Board (03P9348C)

RFC Board (03P9346A) Waveguide Flange

Circulator
MIC Wiring
Antenna Motor Breaker
Shield Cover
(Current Adjustment)
MIC
(RU-9427)

TR Limiter

Fig. 2.2.39 RTR-082 with Magnetron Removed

2-33
 2.3 Monitor Unit

2.3 Monitor Unit

- MU-201CR (20 inch LCD)
- MU-231CR (23 inch LCD)

534 (598)

Hanger

4-( φ )13
454 (505)

35° 409
(451)
Hanger Stay
2-M10 x 30

Hanger Mounting Hole (x4)

with Cover (M6 x 25) 352 (351)

Fig.2.3.1 Monitor Unit (MU-201CR/MU-231CR)

Power Supply Terminal

VIDEO IN
(DVI-D)
Fuse
100 VAC: 2 A
220 VAC: 2 A
24 VDC: 6 A

GND Terminal Cable Clamp

Fig. 2.3.2 Connections on LCD Display Unit

2-34
 2.3 Monitor Unit

Fuse (2 A)
Power Supply DVI I/F Board
AC: PWR Unit (RKW-12-13RE) (SLB-FRN3-A)
DC: DC-DC Board (03P9359)

Noise Filter
LF-205A (AC)
MXB-1206-33 (DC)
LED1 (Always ON)

Fig. 2.3.3 Monitor Unit (MU-201CR) with Cover Removed

LCD Board
(201PW023-H)

Inverter Board
(210PW021-C)

LCD Unit
(NL128102AC31-02)

Fig. 2.3.4 LCD Unit in MU-201CR

2-35
 2.3 Monitor Unit

Fan
(MMS-06C12DS 12VDC 0.17A)

FIL Board
(03P9360)

Power Supply
AC: PWR Unit (RKW-12-13RE)
DVI I/F Board
DC: DC-DC Board (03P9359)
(BSM-501 FN1)

Noise Filter
LF-205A (AC)
MXB-1206-33 (DC)

Fig. 2.3.5 Monitor Unit (MU-231CR) with Cover Removed

LCD Unit
(FLC59UXC8V-04)

Inverter Board
(NA19002-4241)

LCD Board
(NA21808)

Fig. 2.3.6 LCD Unit in MU-231CR

2-36
 2.4 Control Unit

2.4 Control Unit

XH10P-W-5P
L=1.5/10/20/30 m

Left Button
Wheel

Right Button

Power Switch

Trackball

Fig. 2.4.1 Standard Control Unit (RCU-014J) Japanese version

Fig. 2.4.2 Standard Control Unit (RCU-014E) English version

2-37
 2.4 Control Unit

J505 (For PROGRAM update port, J502 (REMOTE) for RCU-016

Factory use)
Cable Clamp
J501 (PROCESSOR) for PRU-013

J506 (EMRI) for EMRI Trackpilot

J507 (SYSTEM FAIL)

CR10 (Option of CPU,
U8, Blinks every second)

U8(CPU) Buzzer Board (03P9362)

PNL Board (03P9343)

Trackball J504 (TB) S36 (DIP SW)

S36 Function
SYSTEM FAIL ALARM
JP1 #1
(ON: Output from J507)
Open (Write Program) RELAY STATUS
Short (Ordinary) #2
(ON: Reversed polarity of the above signal)
#3 Not used
#4 Not used

Fig. 2.4.3 Standard Control Unit (RCU-014) with Cover Removed

2-38
 2.4 Control Unit

Power Switch
RCU-015: Provided
RCU-016: Not provided
XH10P-W-5P-A
L=1.5/10/20/30 m

Fig. 2.4.4 Trackball /Remote Control Unit, RCU-015/016

J521 (PROCESS0R)
- RCU-013 Connector CR11(U5 CPU RUN)
- RCU-016 connects with RCU-015 Blinks every second.
(Remote Panel.)
トラックボール部

JP1
Open (Write Program)
Short (Default)
J527 (SYSTEM FAIL)

J524 (TB)
J522 (REMOTE)
- RCU-015 connects with RCU-016
(PROCESSOR.) ■ PNL 基板 (03P9344)

J525 (PROGRAM, Factory use)

S6 (DIP SW)
S6 Function
SYSTEM FAIL ALARM ON/OFF
#1
(ON: Output from J507)
RELAY STATUS
#2
(ON: Reversed polarity of the above signal)

Fig. 2.4.5 Trackball/Remote Control Unit (RCU-015/016) with Cover Removed

2-39
 2.5 Optional Unit

2.5 Optional Unit

LAN Port
(100BASE-T)
Mini Card Slot (x2) for
C-MAP, NAVIONICS,
and FURUNO chart card. Power Supply
(12 VDC)
Port A Port B

Fig. 2.5.1 Card Interface Unit, CU-200

S1 (DIP SW)
#1: INIT #3: IP1
#2: IP2 #4: IP0
CR2 (U12 CPU RUN,
When two CU-200s are installed, on Blinks every second.)
S1-#4 2nd units is set to ON.

NET-100 Board
(03P9332)

CARD CPU Board

(03P9333)

Fig. 2.5.2 CU-200 with Cover Removed

2-40
 2.5 Optional Unit

100 – 230VAC

Fuse (1 A)

Port Number: 1 to 8
(Lights when in use.)

Link/Act
FDx/Col
10M/100M

RJ45

Fig. 2.5.3 HUB-100

Flip up rotary-lock (a) to release lock

and remove flat cable.

(a)

03P9364

Fig. 2.5.4 HUB-100 with Cover Removed

2-41
 2.5 Optional Unit

LED1 (Always lights.)

Fuse (2 A)

Fig. 2.5.5 DVI I/F Board

A J5 B A J4 B
(Jumper) (Jumper)

A J6 B

Fig. 2.5.6 RGB Buffer Board (03P9229B)

2-42
 2.5 Optional Unit

SW3 (Baud Rate, Version and Talker)

R42 (+5.2 V ADJ, TP1) CR22 (+5.2 V)
Supplied Power

JP4 JP8: BATT Backup

JP5

SW1
(Gear ratio, Type of
JP2 gyrocompass and
(Stator Voltage) frequency)
TP1:+5.2V

JP3 JP9
(Rotor Voltage)

J1
(Type of gyrocompass) SW2
(Rotor Voltage, Stator
Voltage, Self-test,
NMEA Transmitting
interval, CPU reset)

JP6/7 (AD Output Interval,

F1-4 (2 A Fuse) 25 ms/200 ms)
(S1-S3/R1 COM)

J5
(Rotor Signal Input)

J7-12:
J4 (Stator Signal Input) Data Output Port 1-6
J7, J8, J9 (25 ms)
J10, J11, J12 (200 ms)
J6
(NMEA Output Port)
CR21 (CPU RUN,
OK when blinking)

Fig. 2.5.7 GC-10 Board (64P1106A)

2-43
 2.5 Optional Unit

*This unit is used to extend

the antenna cable.

Fig. 2.5.8 Junction Box (RJB-001)

Antenna Motor Power Supply Current Adjustment

Fig. 2.5.9 FAR-2137S/2837S Power Supply Control Unit (PSU-007)

2-44
 2.6 Radar Console

2.6 Radar Console

2.6.1 RCN-003/004: Standard type
600

1100

960

RCN-003 (23-inch Display)

RCN-004 (20-inch Display)
*The dimension of both consoles is
the same.

570

Fig. 2.6.1 RCN-003

Service Window in the rear panel

Cable Entry (Both sides)

Fig. 2.6.2 RCN-003, Side View Fig. 2.6.3 RCN-003, Rear View

2-45
 2.6 Radar Console

Mounting of CU-200

Mounting screw for RCU-014 Unit (x4)

Put the panel lower part by pinching.

Fig. 2.6.4 RCN-003 with Cover Removed

Cable Entry Ground Terminal

Mounting ECDIS
(Non Rader Console)

Mounting PSU-007

GYRO Input Terminal

PSU-007 (Right side of TB Board)
Power-Supply Terminal Output

TB Board
Power Supply Terminal Board

Fig. 2.6.5 Wiring in RCN-003

2-46
 2.6 Radar Console

For VDR BNC connector converter

Foe De-Icer breaker

Fig. 2.6.6 RCN-003 (FAR-2827)

PSU-007

Fig. 2.6.7 RCN-003 (FAR-2837S)

2-47
 2.6 Radar Console

2.6.2 RCN-001/002: Slim type

600
1100

790

788

400

Fig. 2.6.8 RCN-001 (1/2) Fig. 2.6.9 RCN-001 (2/2)

RCN-001 (23 inch Display)

RCN-002 (20 inch Display)
*The dimension of both consoles is
the same.

Mounting CU-200

RPU-013 Power Supply Terminal Board

Cable Entry

Fig. 2.6.10 RCN-001 with Cover Removed

2-48
 2.6 Radar Console

TB Board

Ground Terminal

Fig. 2.6.11 RPU-013, Open View (1/2) Fig. 2.6.12 RPU-013, Open View (2/2)

2-49