ACTIVITIES

ACTIVITY 1
AIM
To assemble the components of a given electrical circuit.

APPARATUS AND MATERIAL REQUIRED

Resistor, ammeter, (0-1.5A) voltmeter (0-5V ), battery, one way key,
rheostat, sand paper, connecting wires.

P ROCEDURE
1. Connect the components
as shown in Fig. A 1.1.
2. After closing the key K,
check that the voltmeter
and ammeter show
deflections on the right
hand side.
3. Check the continuity of the
assembled circuit using a
multimeter (see Activity 4).
Fig. A 1.1 Assembling of given components

R ESULT
The components of the electrical circuit were assembled.

P RECAUTIONS
1. The positive terminal of the battery should be connected to the
positive terminal of ammeter and positive terminal of the voltmeter.
2. The ammeter should be connected in series with the resistor and
the voltmeter should be connected in parallel with the resistor.
3. Sand paper should be used to clean the ends of connecting wires
and leads of the component terminals. Grease/oil or oxide layer

24/04/2018
LABORATORY MANUAL

on their surfaces is insulating in nature and needs to be removed.

However, do not clean the plugs and keys with sand paper.
Excessive use of sand paper in such a case will make the plug
unfit to be used with the key.

D ISCUSSION
1. Draw the circuit diagram of the experiment before you start
connecting apparatus and keep infront of you.
2. The values of the resistances and the current carraying capacity
of the rheostat are given on a plate fixed on the body of rheostat.

S ELF ASSESSMENT
1. What do you mean by emf of a cell?
2. Does the current drawn from the cell remain constant? If
not, why?
3. Why is an ammeter always connected in series with the circuit?
4. Why is a voltmeter always connected in parallel to the component
across which voltage is to be measured?

SUGGESTED ADDITIONAL EXPERIMENTS/ACTIVITIES

1. Design different kinds of circuits that you will study in your class and
assemble them using the relevant components, for example (i) circuit to
measure the value of an unknown resistance using a meter bridge (ii) circuit
to compare e.m.f. of two cells using a potentiometer, etc.
2. Measure the voltmeter and ammeter readings for different rheostat settings
and verify if the ratio of potential difference across the resistor to the current
through it is constant.
3. Modify the circuit using two resistors which may either be connected in
series or in parallel.

140

24/04/2018
 ACTIVITY 13

ACTIVITY 2
AIM
To draw the diagram of given open circuit comprising at least a battery,
resistor/rheostat, key, ammeter and voltmeter. Mark the components
that are not connected in proper order and correct the circuit and
also the circuit diagram.

APPARATUS AND MATERIAL REQUIRED

A given open circuit comprising atleast a cell or a battery, plug
key, resistor, rheostat, ammeter, voltmeter, connecting wires and
sand paper.

P RINCIPLE
An electrical circuit is functional only if all the components of the
circuit are connected in proper order, assuming that all circuit
components/devices are in working condition and key is closed.
An open circuit means a break in some part of a circuit which could
be deliberate such as a key in open position or a fault such as broken
wire or burnt out component(s) or loose connection. Some of such
circuits are given in Figs. A 2.1 (a), (b), (c) and (d).

141
LABORATORY MANUAL

Fig. A 2.1 (a),(b),(c),(d) Open circuits

Note to teachers: In this activity, students are expected to draw

the diagram of a given open circuit comprising a few circuit
components e.g. a key, ammeter, voltmeter, resistor, rheostat etc.
After drawing the given circuit, students would be marking the
components which are not connected in proper order. Then a
correct circuit diagram is to be drawn and accordingly the circuit
components are to be connected in proper order.
Teachers are therefore advised to set up a few open circuits in
which some of the components are not arranged in proper order.

P ROCEDURE
1. Draw the circuit diagrams in your notebook as given by your
teacher [Fig. A 2.1(a), (b), (c) and (d)].
2. Consider one circuit and mark in Table A 2.1, the various
components which have not been connected in proper order.
3. Draw the correct circuit diagram.
4. Connect the electrical components according to corrected circuit
diagram.
5. Close the key in the circuit to verify if the corrected circuit is
functional.

Note: Rheostat can be used both as a variable resistance and potential

divider.
Rheostat as a variable resistance
1. Draw a diagram as given in Fig. A 2.2 (a) showing use of a rheostat
as a variable resistor.
142

24/04/2018
 ACTIVITY 2 13

2. Connect the terminals of rheostat as drawn below using one end

terminal and the other variable terminal.

Variable resistance

Rh

End terminal End terminal

(1) (2)

(a)

Fig. A 2.2 (a) Rheostat as a variable resistor

(b) Rheostat as a potential divider giving variable voltage

Rheostat as a potential divider

1. Draw a diagram as given in Fig. A 2.2 (b) showing use of a rheostat
as a potential divider.
2. Connect the terminals of rheostat as drawn above using (i) the
end terminals (1) and (2) connected to input potential (battery)
and (ii) one end terminal and the other variable terminal for
variable voltage.

O
BSERVATIONS

Table A 2.1: Mark a (P ) in appropriate column

Sl. No. Circuit Correct Incorrect

Component Connection Connection
1 Battery/cell
2 Resistor
3 Rheostat
4 Key
5 Ammeter
6 Voltmeter

R
ESULT
The electrical circuit assembled as per the corrected circuit diagram
is functional.

143

24/04/2018
LABORATORY MANUAL

P RECAUTIONS
1. Ends of the connecting wires should be cleaned with sand paper
before making connections.
2. The positive terminal of the battery should be connected to the
positive terminal of the voltmeter and positive terminal of the
ammeter.
3. The ammeter should be connected in series with the resistor and
the voltmeter should be connected in parallel with it.

D ISCUSSION
1. (a) Rheostat can be used in series as a variable resistance. In
this case, the end terminal (1) and the other variable terminal
is to be used [Fig. A 2.2(a)].
(b) When rheostat has to be used as a potential divider across
the cell, the variable voltage is derived using any one end-
terminal and the variable terminal of the rheostat [Fig. A
2.2(b)].
Justify how the discussion points 1(a) and 1(b) are possible?
2. Key is to be kept “OPEN” so that no damage to the components
occur.

S ELF ASSESSMENT
1. Interpret the function of each component in the circuit.
2. Draw a circuit diagram of a rheostat as a variable resistance
showing the position of sliding contact for (i) maximum resistance
(ii) minimum resistance.
3. What is the function of sand paper in setting up the electric circuit?
4. A rheostat and a resistance box can change the resistance in a
circuit, yet their functions are different. Discuss it.

SUGGESTED ADDITIONAL EXPERIMENTS/ACTIVITIES

1. Draw a circuit diagram using rheostat as a potential divider. Make actual

connection and determine the voltage range it provides.
2. Study the different kinds of keys available in the laboratory and identify
their functions in the electric circuit.
3. Make a detailed study of different types of resistances available in the
laboratory (carbon resistor, wire wound resistance box).
4. Compare the connecting wires used in household circuits and those used in
the laboratory.
5. Make a study of different battery eliminators, dc sources (cells, batteries) in
the laboratories. How are they different as compared to car batteries?
144

24/04/2018
 ACTIVITY 13

ACTIVITY 5
AIM
To assemble a household circuit comprising three bulbs, three
(on/off) switches, a fuse and a power source.

APPARATUS AND MATERIAL REQUIRED

Three bulbs (40 W, 220 V each), three (on/off) switches, socket, a fuse
of 1.0 A, plug, flexible connecting wire, main switch.

P RINCIPLE
If P1, P2, P3, P4, P5, ... be the power consumed by different domestic
electrical appliances in a circuit then the total power consumption, P
at any instant is given by

P = P1+ P2+ P3+ P4+ P5+ ... (A 5.1)

If electric potential is V, then current I drawn from the mains is given by

P (A 5.2)
I =
V

where P is in watt, V in volt

and I in ampere.
In order to protect the
appliances from damage,
when accidentally a high
current is drawn (e.g. when
the terminals of the appliance
get accidentally connected), a
fuse of rating little higher (10
to 20 per cent higher than the
current normally drawn) is
connected in series with the
set of appliances (Fig. A 5.1).
Fig. A 5.1

157

24/04/2018
LABORATORY MANUAL

P ROCEDURE
1. Take the bulbs B1, B2, B3 and connect them in series with switches
S1, S2 and S3 respectively. Connect B1, B2, B3 alongwith S1, S2, S3
in parallel with each other as shown in Fig. A 5.1.
2. Connect fuse F in series with the set up as shown in Fig. A 5.1.
Connect a plug and the socket at the end of two leads. Connect a
wire from the earth pin of the plug.
3. Insert the plug in socket provided in the main electric board.
4. Press the switches S1, S2, S3 one by one and observe the bulb
that is switched on and off independently of the other bulb.
5. Press all the switches simultaneously and observe what happens.
Record your observations.

R ESULT
Household circuit assembly is complete and installed with safety.

P RECAUTIONS
1. Care should be taken while working with mains.
2. Carefully determine the rating of the fuse by calculating the
maximum current drawn by the circuit.

D ISCUSSION
1. Fuse is a safety device. Never use fuse of much higher rating
than the recommended value.
2. The rating of the main electricity in our houses is determined by the
total power requirements. In general it is 220 V, 30 A and
50 Hz. The supply is connected to a distribution board which divides
the power into different circuits; some having a rating of 220 V,
15 A meant for heavy duty appliances like room heater,
airconditioner, geysers, hot plates etc., others have a rating of 220
V, 5 A meant for light appliances like light bulbs, ceiling fans etc.
Let us consider one electrical circuit with 220 V, 5 A supply. In
such a circuit all appliances are connected in parallel with a switch.
This switch is in series with each appliance in supply live line.

S ELF ASSESSMENT
1. Calculate the maximum current drawn for three bulbs used in
the circuit.
SUGGESTED ADDITIONAL EXPERIMENTS/ACTIVITIES
1. Draw a circuit diagram consisting of two light points, one fan point
and one plug point.
158

24/04/2018
 ACTIVITY

ACTIVITY 8
AIM
To identify a diode, a LED, a transistor, an IC, a resistor and a capacitor
from a mixed collection of such items.

APPARATUS AND MATERIAL REQUIRED

Multimeter, a collection of diode, LED, transistor, IC, resistor and
capacitor.

P RINCIPLE
A diode is a two terminal device. It conducts when forward biased
and does not conduct when reverse biased. It does not emit light
while conducting.
A LED (light emitting diode) is also a two terminal device. It conducts
when forward biased and does not conduct when reverse biased. It
emits light while conducting.
A transistor is a three terminal device. The terminals represent emitter
(E), base (B) and collector (C).
An IC (integrated circuit) is a multi-terminal device in the form of a
chip. But some may have only three terminals, e.g. 7805, 7806,
7809, 7912.
A resistor is a two terminal device. It conducts equally in both
directions.
A capacitor is a two terminal device. It does not conduct but stores
some charge when dc voltage is applied.

P ROCEDURE
1. Check the physical appearance of the component.
(a) If it has four or more terminals and has the appearance of a
chip (black rectangular block), then it is an IC.

167

24/04/2018
LABORATORY MANUAL

(a) (a) (b)

+Non
inverting
Inverting

(c)

(d)

(e) (f)

Fig. A 8.1 (a) Diode (b) LED (c) Transistor (d) IC (e) Resistor (f) Capacitor

(b) If it has three terminals, the component may be a transistor.

To confirm, set-up the multimeter in resistance mode
(highest range). Connect its black or common terminal to
one of the extreme legs of the component and the second
terminal (red or positive) to the central leg. Check the
multimeter deflection. If a deflection is observed, interchange
the multimeter terminals. If no deflection is observed, the
component is a transistor. Repeat this test by connecting
the multimeter terminals to the central leg and the other
extreme leg. If a similar behaviour is observed, the
component is a transistor.
(2) If the component has two terminals, it could be a resistor, a
capacitor, a diode or a LED.

168

24/04/2018
 ACTIVITY 8

(a) Look for colour bands, if it has a typical set of three colour
bands followed by a silver or gold band, the component is a
resistor.
(b) Connect the multimeter terminals (in resistance mode-
highest range) to the component terminals and watch for
multimeter deflection. Also repeat by reversing the
component terminals.
(c) If the multimeter shows an equal deflection in both the
directions, the component is a resistor.
(d) If the deflection is accompanied with emission of light, in one
direction and a much less or zero deflection in the other
direction the component is a LED.
(e) If the multimeter does not show any deflection in one direction
and shows deflection with no light emission in the other
direction then, the component is a diode.
(f) If the multimeter does not show any deflection on connecting
its terminals either way to the component, it is a capacitor.
But if capacitance of capacitor is large, multimeter may show
a momentary deflection.
(g) Record your observations in Table A 8.1 and A 8.2.

Note to teachers

(i) Avoid giving an IC with three terminals.

(ii) Preferably use analog multimeter and not the digital
multimeter.
(iii) In case of digital multimeter, the term “deflection” in the
instructions may be read as “reading”.
(iv) Label each component by a different alphabet e.g., A, B,
C, D, E...

O
BSERVATIONS
Table A 8.1 : Checking for the number of terminals

Alphabet marked Name of the Device

Sl.No. No. of terminals
on the device

1 Two
2 Three
3 More than three

169
LABORATORY MANUAL

Table A 8.2 : Checking for the state of conduction

Sl.No. State of Device Code Name of the device

conduction

1 Conducts in one direction

only without any emission
of light
2 Conducts in one direction
only with emission of light
3 Three terminal device;
conducts in one direction
only between central
terminal and either of the
remaining two terminals
4 Conducts in both
directions
5 Does not conduct, gives an
initial deflection which
decays to zero

R ESULT
A diode, a LED, a transistor, an IC, a resistor and a capacitor are
identified respectively from a mixed collection.

P RECAUTION
While obtaining resistance of any component, clean its
leads properly.

S OURCES OF ERROR
1. When the metal ends of a multimeter leads are touched, the
multimeter should show zero resistance. If it does not show
it, bring the pointer to zero using ‘Zero Adj knob’ on the
multimeter. If it is not done, the resistance measurements are
not reliable.
2. While checking resistance of a component, avoid touching either
of the metal ends of the multimeter leads. Body resistance in
parallel with component resistance can affect the resistance
measurement.

170

24/04/2018
 ACTIVITY 8

SUGGESTED ADDITIONAL EXPERIMENTS/ACTIVITIES

Studies of the basic circuit components such as resistor, capacitor

may be undertaken on the following lines:
1. Resistors
Types of resistors
(a) Wire wound resistors: These are made by winding a specified
length of wire of some conducting material. The material may be
any alloy like mangnnin, constantan, nicrome etc.*
(b) Carbon resistors: They are made of a mixture of graphite (a
form of carbon) and a good insulator like shellac in a specified
proportion. The mixture is pressed and moulded onto rods
by heating. By varying this proportion, carbon resistors are
made for a very wide range of values. The stability of such
resistors is poor but they are cheap and small.
(c) Carbon film resistors**: Carbon resistors are cheap and easily
available. A thin film of carbon is deposited onto a small ceramic
rod. The resistive coating is spiralled on it to get the desired value
of resistance.
(d) Thin film resistors: These are made by depositing a very thin film
of a conducting material on some insulating base. The thin film
provides a very small cross-sectional area. Hence a large
resistance. The films may be made from a metal or an alloy.
Tolerance of a resistor
The actual resistance value of a certain resistor may be different from
its specified value. This may be due to external influences like changes
in temperature, humidity etc. or due to the inherent limitation in
manufacturing a given precise value. Deviations in the resistance value
due to later cause is known as tolerance.
Wattage of a resistor
Every resistor has a maximum safe current that it can carry. Currents
larger than that will produce excessive heat and may damage it. This
is usually measured not in terms of the current, but in terms of
maximum watt of power that can be dissipated in the resistor without
causing any damage. It is known as its wattage. Common wattages
for carbon resistors are 1/8, 1/2, 1 and 2 watts. Higher wattages are
also available.
Colour code for resistor
Most common colour code used for resistor consists of three colour
bands at one end.

171
* Wire wound resistors have more undesirable inductance than the other types of resistors.
**See appendix 3 for details.
LABORATORY MANUAL

The colour and their numerical meanings are:

Black – 0 Orange – 3 Blue – 6 White – 9
Brown – 1 Yellow – 4 Violet – 7
Red – 2 Green – 5 Grey – 8
This colour code could be remembered
easily by the term BBROY GB VGW (B B
ROY Great Britain Very Good Wife). To
read the resistance of a colour coded
resistor, start with the strip nearest to
the end. The colour of the first strip gives
the first digit in the resistance value. The
colour of the second strip stands for the
second digit. The colour of third strip
indicates the value of multiplier or the
number of zero following second
number.

Fig. A 8.2 A carbon resistor with colour code marking Resistors with only three bands have a
tolerance of 20%. Its actual value may
vary 20% up or down from its indicated
value. If a fourth band is added separated from the first three, then
the tolerance of the resistor is known from the colour of the fourth
band. If the colour of the fourth band is silver, then tolerance is 10%.
Gold colour represents 5% tolerance red represents 2% and brown
represents 1%. The ohmic values are often printed on 2% and 1%
resistors.

2. Capacitor
Capacitor is a device that stores electrical charge. A capacitor blocks
the passage of dc while it allows ac to flow through it.
There are many types of capacitors having different types of dielectrics
in general use. These are
(i) Air capacitor (variable gang capacitors)
(ii) Mica capacitor (low capacitance)
(iii) Ceramic capacitor (very low capacitance)
(iv) Paper capacitor (low capacitance)
(v) Plastic capacitor
(vi) Electrolytic capacitor (medium capacitance)
(vii) Oil filled capacitor (high capacitance)

172

24/04/2018
 ACTIVITY 8

3. Diode
In some semiconductor junction diodes, a silver ring is shown on one
of its end. This end of the diode is n-side and the other end is p-side
[Fig. A 8.3(a)]. In some diodes, the symbol of the diode is painted on
the body of the diode. The direction of arrow is the direction of current
flow. Hence, the side from which the arrow starts is p-side and the
side towards which the arrow ends is n-side [Fig. A 8.3 (b)]. Some
diodes are bullet shaped in which case the flat side is p-side and the
cylindrical side is n-side [Fig. A 8.3 (c)]. In case of a light emitting
diode (LED), usually the shorter pin is n-side and the longer pin is p-
side [Fig. A 8.3 (d)].

Fig. A 8.3 Shapes of some diodes

4. Transistors
In this activity, a method to distinguish between n-p-n and p-n-p
type transistors has been given, provided the pin diagram of the
transistor is known. In case, if no pin diagram is known, one can still
determine the type (n-p-n or p-n-p) of the given transistor. This can
be done by measuring the resistance values between different
terminals of the given transistor [(Fig. A 8.4) (a) and (b)]. Table A 9.5
(p.181) summarises the nature of resistance values for n-p-n and p-
n-p transistors.

Fig. A 8.4 Different transistor terminals

173

24/04/2018
LABORATORY MANUAL

ACTIVITY 10
AIM
To observe refraction and lateral deviation of a beam of light incident
obliquely on a glass slab.

APPARATUS AND MATERIAL REQUIRED

Drawing board, rectangular glass slab, white sheet of paper,
adhesive tape (cello-tape), drawing pins, a metre scale, alpins,
protractor, sharp pencil and eraser.

PRINCIPLE
When a ray of light is incident on a rectangular glass slab, it is
refracted through it. It emerges out of the slab parallel to the
direction of the incident ray. The emergent ray suffers only a lateral
displacement. For a given angle of incidence and a pair of media,
the lateral deviation is proportional to the thickness of the glass
slab.

PROCEDURE
1. Fix a white sheet of paper on the drawing board with the help of
cello-tape or drawing pins.

2. Place the glass slab lengthwise symmetrically at the centre of the

paper sheet and mark its boundary ABCD (Fig. A10.1) on the
paper sheet with a sharp pencil.

3. Draw a normal at a point F on the face AB. Draw a line EF,

representing the incident ray, making an angle i the angle of
incidence with the normal.

4. Fix two alpins P and Q with sharp tips, about 8 to 10 cm apart,

vertically on the line EF.

5. Observe the images of the two pins through the face

opposite of the glass slab. Fix two more alpins R and S
182

24/04/2018
 ACTIVITY 10

about 8 to 10 cm apart,
vertically on the white paper
sheet carefully with their
tips in line with the tips of
the images of P and Q. Take
care that the tips of all the
alpins appear to be on a
straight line.

6. Remove the glass slab and

mark the pin prick positions
of the alpins on the white
paper sheet with a pencil.
Draw a straight line GH,
representing the emergent
ray, passing through the
points marked R and S,
meeting the face CD at G.

7. Draw the line FG to represent

the refracted ray. Draw a
normal at the point G on the
face CD; making an angle of Fig. A10.1 Refraction through a rectangular glass
emergence e with the normal. slab
Measure the angle of
incidence i a n d a n g l e o f
emergence e with a protractor. Write the values of these angles
on the white paper sheet. Do you find some relation between ∠i
and ∠e ?

8. Extrapolate EF forward to meet the face CD of the glass slab at

O. Draw the perpendicular OL to the line GH.

9. Check if the emergent ray GH is parallel to the incident

ray EF along the original direction. It is laterally
deviated by a perpendicular distance OL. Measure
the lateral deviation OL = d and also the thickness of the
glass slab.

10. Repeat steps 2 to 9 by changing the angle of incidence.

11. Repeat the steps 2 to 10 by using glass slabs of different thickness.

Measure the lateral deviation and the thickness of the glass slab
each time. Also write the values of ∠i and ∠e on the white paper
sheet each time.

12. Record observations in tabular form with proper units. What

inference do you draw from your observations?

183

24/04/2018
LABORATORY MANUAL

O BSERVATIONS
Least count of the protractor = ... (degree)
Least count of the metre scale = ... mm = ... cm

Table A 10.1 : Measuring the angle of incidence i, angle of emergence

e and lateral deviation d.

Thickness of Lateral devia-

Sl.
the Glass Angle of incidence i Angle of emergence e tion d 10–2 m
No. slab, t 10–2 m

(degree) (radians) (degree) (radians)

1 t1
2 t1
-- --
5 t1
6 t2
-- --
10 t2
11 t3
-- --

R ESULT
1. The ray of light emerging from a glass slab is parallel to the incident
ray direction, but is laterally deviated.
2. The lateral deviation of the emergent ray with respect to the
incident ray is directly proportional to the thickness of the
glass slab.

D ISCUSSION
1. The accuracy in the measurement of angles of incidence i and
emergence e and the lateral deviation d depends on how sharp
the pin tips are, and how careful you are in observing the tips of
the pins to lie along the same straight line. Take special care in
observing the tips of the pins, marking the pin pricks, drawing
the incident, refracted and emergent rays with a sharp pencil,
and measuring the angles i and e, accurately with a protractor.

184

24/04/2018
 ACTIVITY 10

S
ELF ASSESSMENT
1. Examine Table 10.1 and interpret the relationship between ∠i
and ∠e, and between t and d.
2. Plot a graph between lateral deviation d along the y-axis and
thickness t of the glass slab along the x-axis using the observed
values from Table 10.1 keeping the angle of incidence same.
Identify the shape of the graph you have obtained and interpret
it.

SUGGESTED ADDITIONAL EXPERIMENTS/ACTIVITIES

1. From the observations with the glass slab placed lengthwise, breadthwise
and thicknesswise, find out the refractive index of the material (glass) of the
slab. Discuss your result.

[Hint: Use sin i/sin r = n (refractive index of the material)]

2. Measure the angle i ′ in each case of the above observations. Calculate the

sin i ′
ratio = n′ . What is the relation between ∠r and ∠i′ and also between
sin e

sin i
∠i and ∠e ? Compare the ratio n' with = n. Remember that the ray
sin r
FG is the incident ray on face CD and GH is the refracted ray. Discuss the
relation between n and n′.

185

24/04/2018
LABORATORY MANUAL

ACTIVITY 13
AIM
To study the nature and size of the image formed by (i) a convex
lens (ii) a concave mirror on a screen by using a candle and a
screen (for different distances of the candle from the lens/mirror).

(i) To study nature and the size of the image formed by a convex
lens. (for different distances of the candle from the lens)

APPARATUS AND MATERIAL REQUIRED

A candle, match box, a small candle-stand, a convex lens of small
focal length and known thickness, a screen with a stand, metre scale.

P RINCIPLE
The position, nature and size of the image of an object formed by a
thin convex lens varies with the change in the position of the object
as illustrated in Fig. A 13 (i).1(a) to A 13 (i).1(f) for some specific
positions. It is assumed that both the spherical surfaces of the lens
have same radi of curvature.

(a) Object is at infinity, i.e., u = ∞. A real, inverted and highly diminished

image is formed at the second principal focus, F2 on the other side
of the lens, i.e. v = f, (i) when incident rays of light is parallel to the
principal axis; and (ii) when incident rays of light are not parallel to
192

24/04/2018
 ACTIVITY 13

A A

B F2 2F2 F2 2F2 B'

2F1 F1 O B' 2F1 B F1 O

A'
(c)
(d)
A'
A'

A
A

B F2 2F2 F2
2F1 F1 O
O B' 2F1 F1 B O

(e) (f)

Fig. A 13 (i). 1 (a), (b), (c), (d), (e), (f) The position, size and nature of the image A′ B′
formed by a thin convex lens LL′ for different positions
of the object AB.

the principal axis, the image is formed on the principal axis and
focal plane respectively.
(b) Object is in between infinity and 2F1, i.e., ∞ > u > 2f. A real, inverted
and diminished image lies in between second principal focus F2
and 2F2 on the other side of the lens, i.e., 2f > v > f.
(c) Object is at 2F1, i.e., u = 2f. A real and inverted image is also
formed at 2F2 on the other side of the lens, i.e., v = 2f. The size of
the image is equal to the size of object.
(d) Object is in between 2F1 and first principal focus F1, i.e.,
2f > u > f. A real, inverted and enlarged image is formed in between
2F2 and infinity on the other side of the lens, i.e., 2f < v < ∞ .
(e) Object is at the first principal focus, i.e., u = f. A highly enlarged,
real and inverted image is formed at infinity on the other side of
the lens, i.e, v = ∞.
(f) Object is in between the principal focus and the optical centre O
of the lens, i.e., f > u > 0. An enlarged, virtual and erect image is
formed on the same side of the object.

193

24/04/2018
LABORATORY MANUAL

P ROCEDURE
1. Obtain an approximate value of the focal length of the convex lens
by focussing the image of a distant object. It can be found by
obtaining a sharp image of Sun or tree on a plain wall, on the
other side of the lens and measuring the distance between the
lens and the wall with a scale. This distance is approximate value
of the focal length, f of the convex lens.
Note: Do not look at the Sun through the lens to see its image as it
will hurt your eyes.
2. Fix a metre scale along the edge (lengthwise) of the table with a
clamp or a cellotape.
3. Fix lens LL′ in a lens stand and place it approximately in the middle
of the metre scale such that its principal axis is horizontal and
parallel to the metre scale. In this position the lens would
lie in a plane perpendicular to the table.

4. Mount a lighted candle vertically on a small

candlestand. Place this candlestand on the
left hand side of the lens. Adjust the upright
such that the tip of the lighted candle lies
on the principal axis of the lens. In this
situation, the height of the tip of the flame
of lighted candle becomes equal to the
height of the optical centre of the lens.
Fig. A 13 (i). 2 Real images of a lighted candle
formed by a thin convex lens.

5. Shift the candlestand (from left side of the lens) to a point slightly
away from 2F1 ( i.e., to a distance slightly more than 2f from the
point O, where f is the focal length of the lens as determined in
step 1). According to Fig. A13 (i).1(b), the image of candle will be
formed at a position closer to the second principal focus F2 on the
right hand side of the lens.
6. Place a vertically mounted screen on the right hand side of the
lens. Adjust its height such that most of its portion lies above the
principal axis of the lens (Fig. A 13 (i)2).
7. Shift the position of the screen near to the second principal focus
F2 on the metre scale functioning as an optical bench.
8. Make final adjustments to get a sharp image of the lighted candle
on the screen. Note the nature of the image.
9. Measure the height of the flame of the lighted candle using a small
plane mirror strip with a graph paper strip pasted on it. Also
194
 ACTIVITY 13

measure the height of the image of the flame being formed on the
screen. For this, fix a small graph paper on the screen. Alternatively,
fix a white paper on the screen and mark the positions of the top
and bottom of the image and determine the height of the image
using a metre scale.
10. Shift the lighted candle towards the lens by a small distance (say
by 5 cm or 3 cm). Repeat steps (8) and (9) and record observations.
In this manner take at least six sets of observations.

O
BSERVATIONS

1. Rough focal length of the convex lens = ...cm

Table A 13 (i) 1 : Position, size and nature of image with different

positions of object

Position Position Size Position Size of Nature of Relative size

Sl.
of of of flame of image on the image image of image
No.
lens (cm) candle (cm) (cm) screen (cm) (cm) (cm) (cm)
1
2
--
6

R
ESULT
1. As the object moves towards the focus of the lens the size of the
image increases and it moves away from the focus. In all these
positions image is real and inverted and is formed on the other
side of the lens.
2. When the object is brought too close to the lens, the image on the
other side is not seen.
3. When the object is at a distance less than the focal length, the
image formed is virtual, enlarged and erect. It is formed on the
same side of the lens as that of the object.

195
LABORATORY MANUAL

P RECAUTIONS
1. This experiment should be performed at a shaded place where no
direct light reaches (preferably in a dark room) otherwise the
images may not be distinctly visible.
2. While estimating the rough value of focal length f of the lens by
focusing the Sun, do not look at the image directly as it may hurt
your eyes.
3. The uprights supporting the optical elements should be rigid and
mounted vertically.
4. The aperture of the lens should be small otherwise the image
formed will not be distinct.
5. Eye should be placed at a distance more than 25 cm from the
image formed on the screen.

D ISCUSSION
1. If the object is placed between the optical centre and focus, the
image so formed will be virtual in nature, you will not get this
image on the screen. Draw the ray diagram.
2. When the candle is placed near the focus, the image is formed at
infinity. It may go beyond the end of the table.

S ELF ASSESSMENT
1. How does the size of your image formed by a convex lens vary as
you move from the other end of the table towards the lens?
2. Where should the object be placed to get a virtual and erect image
of the object?
3. What should be the position of the object to get an image on the
same side of the lens as the object?
4. How does the position of the image formed by a convex lens vary
as you move along the principal axis of the lens from infinity to its
focus?
5. What will be the position of the object to get a real image having
the same size as the object?

196

24/04/2018
 ACTIVITY 13

AIM
(ii) To study the nature and size of the image formed by a
concave mirror on a screen by using a candle and a screen
(for different distances of the candle from the mirror).

APPARATUS AND MATERIAL REQUIRED

An optical bench, candle, match box, a small candlestand, concave
mirror of nearly 25 cm focal length, a screen, three uprights (with
clamps), metre scale, adhesive tape and spirit level.

P RINCIPLE
The position, nature and size of the image of an object formed by a
concave mirror changes with the position of the object. Figs. A13(ii).
1 (a) to (f), show the image formation by placing the object at different
positions in front of the mirror in different situations.
(a) Object is at infinity, i.e., u = ∞ . A real, inverted and highly
diminished image is formed at the principal focus, i.e., v = f.
(b) Object is in between infinity and the centre of curvature, i.e.,
∞ > u > 2f. A real, inverted and diminished image lies in
between C, the centre of curvature and principal focus, F,
i.e., f < v < 2f.
(c) Object is at centre of curvature, i.e., u = 2f. A real and inverted
image is formed at the centre of curvature, i.e., v = 2f. The size of
the image is equal to the size of object.

197

24/04/2018
LABORATORY MANUAL

(virtual image cannot

be obtained on a screen)

Fig. A 13 (ii).1 (a),(b),(c),(d),(e),(f) Formation of images by a concave mirror

(d) Object is in between the centre of curvature and principal

focus, i.e., 2f > u > f. Real, inverted and enlarged image is
formed in between C, the centre of curvature and infinity,
i.e., 2f < v < ∞ .
(e) Object is at the principal focus F, i.e., u = f. A highly enlarged,
real and inverted image is formed at infinity, v = ∞ .
(f) Object is in between the principal focus F and pole of the mirror
P, i.e., f > u > 0. An enlarged, virtual and erect image is formed
behind the mirror.
A real image (always inverted) is the one through which the rays
of light actually pass after reflection from concave mirror and
which can be formed on a screen. A virtual image (always erect)
is the one through which the rays do not actually pass, although
they appear to come from it. Thus, the images of an object (e.g.,
a burning candle) formed for situations illustrated in Figs. A13
(ii).1 (a) to (d) can be focussed on a screen. The size of image
may be determined by using a graph paper fixed on the screen.

198

24/04/2018
 ACTIVITY 13

P
ROCEDURE
1. Obtain an approximate value of the focal length of the concave
mirror by focusing the image of a distant object. It can be found
by obtaining a sharp image of the Sun or a tree on a plane wall,
or on a sheet of paper and measuring the distance between the
mirror and the image with a scale. This distance is an approximate
value of the focal length, f of the concave mirror. Twice of this
focal length is an approximate value of the radius of curvature
of the mirror.
2. Place the optical bench on a rigid platform and using the spirit
level make it horizontal with the help of levelling screws provided
at the base of the bench.
3. Clamp the concave mirror on an upright and fix it near one
end of the optical bench such that its principal axis is
horizontal and parallel to the optical bench. In this position
the mirror would lie in a plane perpendicular to the principal
axis of the mirror.
4. Mount a lighted candle vertically on a small candlestand and
fix it on an upright. Place this upright near the reflecting
surface of the mirror. Adjust the upright so that the height of
the bottom of the candle (or top of the candlestand) becomes
equal to the height of the pole P of the mirror from the base of
the optical bench. In this situation the bottom of the candle
(or the top of the candlestand) would lie on the principal axis
of the mirror.
5. Mount the screen on another upright and adjust the height of
its top equal to the height of pole P from the base of the optical
bench. Thus, the position of the screen lies below the principal
axis of the mirror.

Note: In situations where ∞ > u > R; R > v > f, the object is kept above
the principal axis and screen is kept below the principal axis as shown
in Fig. A 13 (ii).2(a).

6. Shift the candle upright to another end of the optical bench so

that the distance of the candle from the mirror is much larger
than the focal length of the concave mirror. Thus, the position of
the candle in front of the mirror can be considered to be distant,
i.e., u >> R, and the image of the candle will be formed at a
position much closer to the principal focus F of the mirror [Fig.
A13 (ii).1 (a)] or v
f.
7. Read the positions of the mirror, screen and candle uprights on
the optical bench metre scale and record the readings in the
observation table.
199

24/04/2018
LABORATORY MANUAL

8. Measure height of the lighted candle using the metre scale. Also
measure the height of the image formed on screen as done in
step 9 of activity 13 (i).
9. Bring the lighted candle close to the centre of curvature C
(distance PC = 2 f ). Now the image will be formed in between the
points C and F, close to 2f. Adjust the position of the screen to
get a sharp image [Fig. A 13 (ii). 1(b)].

u M v M

P P
C F C F
f f

v u
M′ M′
2f 2f
(a) (b)

Fig. A 13 (ii). 2 Real images of a lighted candle formed by a concave mirror (a) u > v; and (b) u < v.

10. Place the candle at C. Shift the position of the screen near to the
principal focus F on the optical bench. Use the rough estimated
value of the focal length f of the mirror as determined in Step 1.
Make final adjustments to get a sharp image of the lighted candle
on the screen. Note the nature of the image.
11. Repeat steps 7 and 8 and record the observations and also note
the nature of image formed.
12. Shift the lighted candle such that R > u > f. Now the
image will be formed in between the point C and infinity,
i.e., ∞ > v > R [Fig. A13(ii).1(d)]. Now since u < v, the candle
(object) is placed below the principal axis while the screen
is placed above the principal axis, i.e. the top of candle
and bottom of the screen lie on principal axis as shown in [Fig.
A13 (ii). 2 (b)].

13. Repeat above steps by placing the candle at F and then between
F and P. Record your observations in Table A 13 (ii).1.

Note: When candle is placed at the centre of curvature C (i.e., u = R),

this method may not be useful for locating the position of image as it
is difficult to mount both the screen and candle at the same place on
the optical bench.
200

24/04/2018
 ACTIVITY 13

O
BSERVATIONS
Approximate focal length of the concave mirror =...cm
Table A 13 (ii).1: Nature, size and position of image with different
positions of object

Position Position Size Position Size of Nature of Relative size

Sl.
of of of flame of image on the image image of image
No.
mirror (cm) candle (cm) (cm) screen (cm) (cm) (cm) (cm)
1
2
--
6

R ESULT
Observation on the nature, size and position of image shows that
1. The image moves away from the focus as the object is moved
towards the focus.
2. The size of the image increases as it moves away from the mirror.
3. If the object is placed between infinity and F the image formed by
a concave mirror is real and inverted.
4. If the object is placed between F and pole, the image is formed
behind the mirror and it is virtual, erect and enlarged.

P
RECAUTIONS
1. This experiment should be performed at a shaded place where
no direct light reaches (preferably in a dark room) otherwise the
images may not be distinctly visible.
2. While estimating the rough value of focal length f of the mirror
by focusing the Sun, do not look at the Sun through the mirror
as it may hurt your eyes.
3. The uprights supporting the optical elements should be rigid and
mounted vertically.
4. The aperture of mirror should be small otherwise the image
formed will not be distinct.
5. Eye should be placed at a distance more than 25 cm from the
image being formed on the screen.
201

24/04/2018
LABORATORY MANUAL

6. An error may arise in the observations if the top of optical bench

is not horizontal.
7. The general instructions to be followed in all optical bench
experiments must be taken care of.
8. The concave mirror should be front-coated. Otherwise multiple
reflections coming from the reflecting surface of the mirror will
confuse the accurate position of the image.

D ISCUSSION
1. You cannot exactly observe the characteristics of the image
formed when the object is between focus and pole of the mirror.
You can only check by moving the screen in front of it that the
image is not formed in front of the mirror. By drawing ray
diagram it can be seen that the virtual image is formed behind
the mirror.
2. The inferences corresponding to u= ∞ and u=f also be elicited by
the trends you observe and drawing ray diagrams, because, the
object and image (respectively) are situated outside the range of
optical bench.
3. The situation corresponding to u= 2f, may also be difficult to locate
because you have to place the candle and the screen at the same
position.

S ELF ASSESSMENT
1. The focal length of a concave mirror is 20 cm, what is its radius of
curvature?
2. When an object is placed at 30 cm in front of a concave mirror, image
of the same size is formed. What is the focal length of the mirror?
3. Focal length of a concave mirror is 30 cm. What will be the
characteristics of the image formed, when the object is placed at a
distance of 40 cm in front of the mirror?
4. What is the effect on the size and intensity of the image formed
when the lower half of the concave mirror is painted black?
5. Is it possible to get a virtual image on the screen? If so, how?
6. In a similar experiment using lenses, the images look a little
coloured, unlike this experiment. What is the reason for this?

SUGGESTED ADDITIONAL EXPERIMENTS/ACTIVITIES

Using a plane mirror and a single pin determine the focal length of a given
convex lens.
202

24/04/2018