Ford - Rec Kit

4.6L/5.
4L SOHC MODULAR (2 Valve) - Low Lift Design

1994-1998 (Early Model Cylinder Head)
Note: These cams use .000" intake and exhaust valve lash.
Ford
Rec Kit
X-TREME MILEAGE CAMS AVAIL ABLE!

CONTACT CROWER TECHNICIANS FOR MORE INFO.
Description
Part Number Advertised Duration Intake Exhaust Duration Gross Lift @ .050" Lobe Lift (1.8) Intake Exhaust Intake Exhaust Intake Exhaust
FACTORY OEM SPECS (1994-98) STAGE 1 Excellent for stock replacement. No other modifications required. RPM Range: 1250 to 5750+ on 4.6L, 5.4L will be lower. STAGE 2 Hot street profile. Emphasis on mid range. Spring recommended. RPM Range: 1500 to 6000+ on 4.6L, 5.4L will be lower. STAGE 2 Designed specifically for supercharger applications for street use. RPM Range: 1750 to 6500+ on 4.6L, 5.4L will be lower. STAGE 3 Street/strip profile. Emphasis on top end power. Spring required. RPM Range: 2000 to 6750+ on 4.6L, 5.4L will be lower. CUSTOM GROUND 4.6L/5.4L CAMS - Special order custom ground profiles available for an additional charge. Proprietary and confidential profiles also available.
Stock
233 Lobe 242 186 Lobe 191 .256" .259" 242 Valve 254 202 Valve 207
.461" .466" Stock .500" .529" Stock 84706 or 84707 84706 or 84707 84706 or 84707
234 Lobe 248 186 Lobe 197 .278" .294" 62810-2 248 Valve 262 202 Valve 213 252 Lobe 256 204 Lobe 208 .296" .296" 62811-2 266 Valve 270 220 Valve 224 258 Lobe 258 212 Lobe 212 .296" .296" 62812-2 272 Valve 272 230 Valve 230 262 Lobe 262 216 Lobe 216 .293" .293" 62813-2 276 Valve 276 234 Valve 234
.532" .532"
.532" .532"
.527" .527"
00080-2
Refer to page 7 for camshaft recommendation form
The above cams are ground on factory 114 lobe center. Valve timing events are available online at: www.crower.com/valvtime.html
ENGINEERED COMPONENT KITS
Remarks Retainers Part No. Springs 84706 68193-16 87025-16 High pressure spring, steel retainer for street and high mileage use. 84707 68193-16 87025T-16 High open pressure spring, titanium retainer for limited street & race. Spring pressure: 68193-16 Seat: 1.720" @ 124 lbs / Nose: 1.100" @ 257 lbs / Coil bind: 1.035" (No machine work required).
NEW HIGH RPM VALVE SPRING
Remarks Part No. 97434I-8 Stainless steel valves - 44.5 mm head dia (8 only int) 97434E-8 Stainless steel valves - 34 mm head dia (8 only exh) 97432I-8 Stainless steel valves - 46.83 mm head - M-6049-D46 Cyl Head 97435E-8 Stainless steel valves - 36 mm head - M-6049-D46 Cylinder Head Note: When ordering valves, be sure to specify one set int and one set exh.
ACCESSORIES
STAINLESS STEEL VALVES Made from the highest grade stainless steel, this new Crower valve is a must for high horsepower, high boost and high rpm applications. The exclusive Pro Flo head design delivers a significant increase in cylinder head flow figures, while the tip area is hardened to RC50, including past the critical keeper groove area for added strength. Fully CNC machined and swirl polished to insure that you will get the best performance valve available on the market. Choose from standard and 1mm oversize. Titanium valves also available.
For technical support call 619-661-6477 Some products listed are not legal for sale or use on emission controlled motor vehicles RPM ranges vary upon application www.crower.com
67
Ford
Description
1999-up (Late Model Cylinder Head)
4.6L/5.4L SOHC MODULAR (2 Valve) - High Lift Design

Part Number Advertised Duration Gross Lift Duration @ .050" Lobe Lift (1.8) Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust Rec Kit
FACTORY OEM SPECS (1999-up)
Stock
233 Lobe 239 184 Lobe 191 .280" 242 Valve 252 200 Valve 209
.295" .504" .531" Stock .303" .529" .545" Stock
243 Lobe 250 193 Lobe 196 STAGE 1 - BAJA BEAST 62905-2 .294" 257 Valve 264 209 Valve 212 Tow package. Specifically designed for heavy trucks/SUV applications. RPM Range: Idle to 5500+ on 4.6L, 5.4L will be lower. STAGE 1 Excellent for stock replacement. No other modifications required. RPM Range: Idle to 5500+ on 4.6L, 5.4L will be lower. STAGE 2 Hot street profile. Emphasis on mid range. Spring recommended. RPM Range: 1250 to 6000+ on 4.6L, 5.4L will be lower. STAGE 2 Designed specifically for supercharger applications for street use. RPM Range: 1500 to 6500+ on 4.6L, 5.4L will be lower. STAGE 3 Street/strip profile. Emphasis on top end power. Spring required. RPM Range: 1750 to 6750+ on 4.6L, 5.4L will be lower. STAGE 3 Designed specifically for supercharger applications for street/strip. RPM Range: 2000 to 6900+ on 4.6L, 5.4L will be lower. STAGE 4 Race grind. ECU mods and tuning required. Rough idle is common. RPM Range: 2250 to 7000+ on 4.6L, 5.4L will be lower. CUSTOM GROUND 4.6L/5.4L CAMS - Special order custom ground profiles available for an additional charge. Proprietary and confidential profiles also available. 62800-2 246 Lobe 250 200 Lobe 204 .300" 260 Valve 264 216 Valve 220 254 Lobe 258 208 Lobe 212 .311" 268 Valve 272 224 Valve 228 262 Lobe 262 216 Lobe 216 .322" 276 Valve 276 234 Valve 234 266 Lobe 270 220 Lobe 224 .328" 280 Valve 284 238 Valve 242 274 Lobe 274 228 Lobe 228 .340" 288 Valve 288 246 Valve 246 274 Lobe 278 228 Lobe 232 .340" 288 Valve 292 246 Valve 250
.305" .540" .549" Stock
62801-2
.317" .559" .570" 84706 84706 or 84707 84706 or 84707 84706 or 84707 84706 or 84707
62802-2
.322" .581" .581"
62803-2
.334" .590" .601"
62804-2
.340" .612" .612"
62805-2
.345" .612" .621"
00080-2
The above cams are ground on factory 114 lobe center. 1999 and up SOHC engines require cam gears to replace pressed on units. Valve timing events are available online at: www.crower.com/valvtime.html

Remarks Retainers Part No. Springs 84706 68193-16 87025-16 High pressure spring, steel retainer for street and high mileage use. 84707 68193-16 87025T-16 High open pressure spring, titanium retainer for limited street & race. Spring pressure: 68193-16 Seat: 1.720" @ 124 lbs / Nose: 1.100" @ 257 lbs / Coil bind: 1.035" (No machine work required).
ACCESSORIES
Part No. 97434I-8 97434E-8 97432I-8 97435E-8 Remarks Stainless steel valves - 44.5 mm head dia (8 only int) Stainless steel valves - 34 mm head dia (8 only exh) Stainless steel valves - 46.83 mm head - M-6049-D46 Cyl Head Stainless steel valves - 36 mm head - M-6049-D46 Cylinder Head
Note: When ordering valves, be sure to specify one set int and one set exh.
Ford Timing Gears Part Numbers: F8AE-6256-BA (Left Hand Gear) F8AE-6256-AA (Right Hand Gear) F1AZ-6278-A (Washer) F1AZ-6A340-A (Bolt) F3AZ-6265-A (Spacer)
68
4.6L/5.4L SOHC MODULAR (3 Valve)

2005-up
Ford
Rec Kit

Description
Part Number Advertised Duration Gross Lift Duration @ .050" Lobe Lift (1.8) Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust
FACTORY OEM SPECS (1999-up) STAGE 1 Excellent for stock replacement. Programming recommended. RPM Range: 1000 to 5900+ RPM STAGE 2 Hot Street Profile with explosive mid-range torque. Supercharged/Nitrous. RPM Range: 1200 to 6200+ RPM STAGE 3 Street/Strip profile. Mid/Top end cam. 2500 stall rec. RPM Range: 1200 to 6400+ RPM CUSTOM GROUND 4.6L/5.4L CAMS - Special order custom ground profiles available for an additional charge. Proprietary and confidential profiles also available.
Stock
232 Lobe 260 175 Lobe 198 .216" .216" .432" .432" Stock 246 Valve 274 193 Valve 216
62830-2 245 Lobe 262 188 Lobe 200 .240" .234" .480" .468" 84708 261 Valve 278 208 Valve 222 114 62831-2 258 Lobe 268 200 Lobe 216 .246" .246" .492" .492" 84708 274 Valve 284 220 Valve 236 114 62832-2 268 Lobe 278 212 Lobe 228 .246" .251" .490" .502" 84708 284 Valve 294 222 Valve 248 115 00082-2
Part No. Springs Retainers Remarks 84709 68193-24 87023-24 Steel Retainer, for daily street use. 84708 68193-24 87023T-24 High pressure spring, titanium retainer.
Spring pressure: 68193-24 Seat: 1.660" @ 130 lbs / Nose: 1.100" @ 257 lbs / Coil bind: 1.035" (No machine work required).
69
Ford
Description
4.6L/5.4L DOHC MODULAR (4 Valve)

Part Number
FACTORY OEM SPECS STAGE 1 - BAJA BEAST Tow package. Specifically designed for heavy trucks/SUV applications. Stock Idle. STAGE 1 Excellent for stock replacement. No other modifications required. Stock Idle to 6800 rpm. STAGE 2 Hot street profile. Emphasis on mid range. Spring recommended. Slight Lope at Idle to 7000 rpm. STAGE 2 Designed specifically for supercharger applications for street use. Slight Lope at Idle to 7250 rpm. STAGE 3 Street/strip profile. Emphasis on top end power. Spring required. Rough Idle to 7500 rpm. STAGE 3 Designed specifically for supercharger applications for 3/4 race. Rough Idle 7750+ rpm. STAGE 4 Race grind. ECU mods and tuning required. Rough idle is expected. Rough Idle to 7800+ rpm. CUSTOM GROUND 4.6L/5.4L CAMS - Special order custom ground profiles available for an additional charge. Proprietary and confidential profiles also available.
Advertised Duration Duration Gross Lift (.006") @ .050" Lobe Lift (1.8) Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust
Rec Kit
Stock
220 Lobe 228 172 Lobe 178 .218" .217" .392" .390" Stock 232 Valve 240 186 Valve 194
Lobe 228 176 Lobe 182 62925-4 222 .234" .237" .421" .427" Stock 234 Valve 240 192 Valve 198
Lobe 232 176 Lobe 188 62820-4 222 .234" .239" .421" .430" Stock 234 Valve 244 192 Valve 204
84710 Lobe 246 194 Lobe 200 62821-4 238 .262" .263" .472" .473" or 250 Valve 258 210 Valve 216 84711 84710 Lobe 252 206 Lobe 206 62822-4 252 .264" .264" .475" .475" or 264 Valve 264 222 Valve 222 84711 84710 Lobe 262 212 Lobe 216 62823-4 258 .269" .269" .484" .484" or 270 Valve 274 228 Valve 232 84711 84710 Lobe 258 212 Lobe 212 62824-4 258 .269" .269" .484" .484" or 270 Valve 270 228 Valve 228 84711 84710 Lobe 274 220 Lobe 228 62825-4 266 .270" .275" .486" .495" or 278 Valve 286 236 Valve 244 84711 00084-4

The above cams are ground on factory 114 lobe center. Valve timing events are available online at: www.crower.com/valvtime.html

Part No. 84711 84711X2 84710 84710X2 Springs 68194-32 68194X2-32 68194-32 68194X2-32 Retainers 87026-32 87020-32 87026T-32 87020T-32 Remarks High pressure spring and steel retainer kit. Daily street use. High pressure spring and steel retainer kit. Daily street use. High pressure spring and titanium retainer kit. Limited street. High pressure spring and titanium retainer kit. Limited street.
Spring pressure: 68194-32 Seat: 1.420" @100 lbs / Nose: 0.910" @ 244 lbs / Coil bind: 0.850" (No machine work required). 68194X2-32 Seat: 1.470" @ 108 lbs / Nose: 0.970" @ 240 lbs / Coil bind: 0.855" (No machine work required).
ACCESSORIES
Remarks Part No. 97437I-16 Stainless steel valves - 37 mm head dia (16 only int) 97437E-16 Stainless steel valves - 30 mm head dia (16 only exh) 97438I-16 Stainless steel valves - 38 mm head dia (16 only int) 97438E-16 Stainless steel valves - 31 mm head dia (16 only exh)
70
FOCUS ZX3 - Twin Cam (1998-up)

Note: These cams use .006" intake (cold), .008" exhaust valve lash (cold).
Advertised Duration (.010") Intake Exhaust Duration @ .050" Intake Exhaust
Ford
Rec Kit
Description
Part Number
Lobe Center
Lobe Lift Intake Exhaust
FACTORY OEM SPECS (1998-up) STOCK REPLACEMENT Mild profile for automatic transmission. Stock idle. RPM Range: Idle to 6500+ STAGE 1 Automatic or mild turbo/supercharger. No head work required. RPM Range: Idle to 6500+ STAGE 2 Street/Strip package. Perfect for all-motor use. Spring #68195 rec. RPM Range: 1000 to 7000+. STAGE 2 Forced induction special. Designed specifically for turbo or super charged applications. Requires spring kit. RPM Range: 1500-up. STAGE 3 - 34 Race Recommended for mostly strip use. Must clearance cylinder head. RPM Range: 1200 to 8000+ STAGE 4 - Full Race All out, all motor drag profile. Not for the inexperienced tuner. RPM Range: 1300 to 8500+
Stock 62500-2
112 114
276 Lobe 273 252 Valve 249 262 Lobe 262 238 Valve 238 268 Lobe 268 244 Valve 244 280 Lobe 276 256 Valve 252 276 Lobe 276 252 Valve 252 292 Lobe 284 268 Valve 260 300 Lobe 292 276 Valve 268
206 Lobe 205 200 Valve 199 214 Lobe 214 208 Valve 208 220 Lobe 220 214 Valve 214 232 Lobe 228 226 Valve 222 228 Lobe 228 222 Valve 222 244 Lobe 236 238 Valve 230 252 Lobe 244 246 Valve 238
.346" .341" Stock .352" .352" Stock
62501-2
114
.374" .374" Stock
62502-2
114
.413" .393" 84169
62502T-2
114
.393" .393" 84169
62503-2
114
.433" .413" 84169
62504-2
114
.454" .433" 84169
CUSTOM GROUND ZX3 CAMS - Special order custom ground 00071-2 Refer to page 7 for camshaft profiles available for an additional charge. Proprietary and recommendation form confidential profiles also available. Note: If running ZX2 cylinder head, the intake cams will work with your application, however the exhaust cams will not fit. Must run factory exhaust cam. * Indicates a spec change from previous catalog.
Part No. Springs Retainers Remarks 84169 68195-16 *87082-16 Fits ZX3 and ZX2 heads
Spring pressure: 68195-16 Seat: 1.400" @ 66 lbs / Nose: 0.950" @ 174 lbs / Coil bind: 0.860" (No machine work required on most heads). * Due to casting inconsistencies, some cylinder heads may require machine work for valve spring, use cutter #68974.
ACCESSORIES
Part No. 86054FB 86054FC 97430I-8 97430E-8 97431I-8 97431E-8
Remarks Adjustable Cam Sprocket (1 only). All black. 2 required Adjustable Cam Sprocket (1 only). Black & Silver. 2 required Stainless steel valves - 32 mm head dia (8 only int) Stainless steel valves - 28 mm head dia (8 only exh) Stainless steel valves - 33 mm head dia (8 only int) Stainless steel valves - 29 mm head dia (8 only exh)
Note: When ordering valves, be sure to specify one set int and one set exh. Note: When ordering sprockets, be sure to specify two.
ADJUSTABLE SPROCKETS Crower's new cam sprockets are made from premium 6061-T6 billet aluminum and incorporate a four bolt ARP fastening system to prevent the slippage found in other brands. For the ultimate tuner, Crower sprockets feature 5/16" diameter, 12 point ARP fasteners with a hardened washer to prevent galling and stripping. The lightweight design reduces unwanted harmonics which could cause valve train failure.
71
Ford / Mazda
Description
2.0 & 2.3L DURATEC - Twin Cam

FOCUS PZEV & ST, 4 CYL RANGER
Note: These cams use .006" intake (cold), .008" exhaust valve lash (cold).
Advertised Duration Duration (.010") @ .050" Lobe Lift Intake Exhaust Intake Exhaust Intake Exhaust
Part Number
Lobe Center
Rec Kit
Ford Focus ST (2004) STOCK REPLACEMENT Similar specifications to stock cam profile. No modifications req. Works with stock springs and other components. RPM Range: Idle to 6500+ STAGE 1 Street use with emphasis on bottom end and mid range power. Works with stock springs up to factory rev limiter. RPM Range: Idle to 7000+ STAGE 2 - Forced Induction Designed specifically for turbo or supercharger applications. Low duration, high lift profile. Requires Crower spring kit #84170. RPM Range: Idle to 8000+
Stock 62550-2
112 114
256 255
252 255
202 214
189 204
.358" .317" .363" .328"
Stock Stock
62551-2
114
268
252
220
214
.374" .363"
84170
62551T-2
112
270
270
220
220
.400" .400"
84170
STAGE 2 - 3/4 Race Designed for street/strip applications in normally aspirated engines. 62552-2 Requires spring/retainer kit #84170. RPM Range: 1000 to 7800+ STAGE 3 - Full Race Drag Race and radical Street/Strip. Requires #84170 spring kit and compatible ECU upgrade for optimum results. Rough idle. RPM Range: 1100 to 8000+ CUSTOM GRIND - Crower can custom grind cams to your desired specs, also proprietary profiles available upon request.
Duration figures are taken at the lobe.
112
276
268
228
220
.389" .373"
84170
62553-2
112
284
276
236
228
.414" .393"
84170
ENGINEERED COMPONENT KIT

Retainers Remarks Part No. Springs 84170 68195-16 87083-16 Titanium retainer intended for race and limited street Spring pressure: 68195-16 Seat: 1.400" @ 66 lbs / Nose: 1.000" @ 161 lbs / Coil bind: 0.860" (No machine work required).
ACCESSORIES
Part No. 97427I-8 97427E-8 97428I-8 97428E-8 97429I-8 97429E-8 Remarks Stainless steel valves - 35 mm head dia (8 only int) Stainless steel valves - 30 mm head dia (8 only exh) Stainless steel valves - 35.5 mm head dia (8 only int) Stainless steel valves - 30.5 mm head dia (8 only exh) Stainless steel valves - 36 mm head dia (8 only int) Stainless steel valves - 31 mm head dia (8 only exh)
Note: When ordering valves, be sure to specify one set int and one set exh.
72
Note: These cams use .008" intake, .010" exhaust valve lash.
2000cc 4 Cylinder (3 Bearing)
SOLID CAMSHAFTS
Description
Gross Lift Part Grind Lobe Advertised Duration Duration @ .050" C.I.D. 1.6 / 1.6 Group Number Center Intake Exhaust Intake Exhaust Intake Exhaust
Ford
.450" .469" .491" .513"
ULTRA BEAST / PERFORMANCE LEVEL 4 - Race only performance. Emphasis on upper mid-range and top end power. RPM Power Range: 2750 to 6750 / Redline: 7000 max.
All cid
25360 296FDP 107 25304 240FDP 112 25305 250FDP 110 25306 264FDP 108 25307 276FDP 108 25308 288FDP 106 25309 302FDP 106 25310 308FDP 106 00000
292 240 250
296 264 276
231 202 216
242 .448" 216 .445" 226 .469"
MILEAGE COMPU-PRO / PERFORMANCE LEVEL 1 - Enhances mileage and All torque in stock engines. RPM Power Range: Idle to 3500 / Redline: 4500 plus. cid POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power/mileage with extended rpms. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. All cid
HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 - Hot street. All cid Strong upper bottom and top end power. RPM Power Range: 1800 to 4500 / Redline: 6000 plus. ULTRA-PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 - Hot street/drag. Strong mid to top end power. RPM Power Range: 2000 to 6000 / Redline: 7000 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Super torque, short oval/radical street grind. RPM Power Range: 2500 to 6000 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Super mid-range to top end profile. RPM Power Range: 3000 to 6500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Upper mid-range with exceptional top end torque. RPM Power Range: 4000 to 7500 plus. CUSTOM GROUND SOLID - Special order solid lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. All cid All cid All cid All cid All cid
264
288
230
240 .490"
276
302
234
250 .514"
.534"
288 302 308
302 308 312
254 264 272
268 .528" 268 .563" 280 .570"
.561" .573" .571"
Note: The above solid profiles are ground with a smaller base circle than stock. If using stock length valves, you must use .055" thick lash caps (86126-8) in kit below. Check follower geometry with Dykem hi-spot blue or any other non-drying compound and adjust valve length accordingly (see diagram 1). Duration numbers @ .050" have been refigured to reflect valve lift.
Diagram 1. Follower Geometry (Sample based on intake of 25307)
ENGINEERED COMPONENTS
Springs Retainers Lash Caps
Lobe Lift
Remarks
.321" x 1.6 = .514"
Rocker Ratio
Gross Lift
Correct Contact surface
68324-8 87044-8
86126-8
For rpm up to 7000 max.

Lobe Lift Rocker Ratio Gross Lift
Spring pressure: 68324-8 Seat: 1.600" @ 118 lbs / Nose: 1.000" @ 283 lbs / Coil bind: 0.910" (Machine work, use cutter 68983*). * Machine work required, specify 516 pilot shaft when ordering. Note: Ford overhead camshafts are susceptible to lobe wear. We highly recommend breaking in new cam and followers with a light pressure break-in spring for a minimum of 30 minutes. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
.321" x 1.52 = .488"
Wrong Valve or Lash Cap too short
.321" x 1.7 = .546"
Lobe Lift
Rocker Ratio
Gross Lift
Wrong Valve or Lash Cap too long
Note: When you achieve the indicated gross lift for your cam, the geometry and wear pattern are correct. Failure to achieve proper follower geometry will result in severe lobe wear.
73
Ford
HYDRAULIC CAMSHAFTS
2300cc 1974-up 2000cc 1982-up (4 Bearing)

Duration Gross Lift C.I.D. Part Grind Advertised Duration @ .050" 1.66 / 1.66 Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust
BAJA BEAST / PERFORMANCE LEVEL 3 - Excellent low end and mid-range power. RPM Power Range: 1800 to 4500 / Redline: 5500 plus. POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power/mileage with extended rpms. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 - Hot street. Strong upper bottom/top end power. RPM Power Range: 1800 to 4500 / Redline: 6000 plus.
Note: Lift rule camshafts are available from Crower on a special order basis.
Description (Note: See pages 8-9 for a detailed explanation of each Performance Level)
All cid All cid All cid
24915
280H 108
280 270
280 222 286 228
222 .410" 238 .476"
.410" .493"
24273 270HDP 110 24274 286HDP 110
286
297 244
253 .488"
.511"
SOLID CAMSHAFTS
POWER BEAST / PERFORMANCE LEVEL 4 - High torque racing profile with bottom end power. RPM Power Range: 2800 to 6400 / Redline: 6800 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 5 - Torque with excellent mid-range power. RPM Power Range: 3000 to 6500 / Redline: 7000 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 5 - Strong mid-range and top end power profile. RPM Power Range: 4000 to 7000 / Redline: 7500 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 5 -Upper mid-range and top end power. RPM Power Range: 4500 to 7500 / Redline: 8000 plus.
Note: These cams use .012" intake, .014" exhaust valve lash. Duration Gross Lift Description Part Grind Advertised Duration @ .050" C.I.D. 1.66 / 1.66 (Note: See pages 8-9 for a detailed explanation of each Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust Performance Level)
All cid All cid All cid All cid
24360
302F 109
302
307 252
262 .459" .461"
24372 288FDP 106 24374 311FDP 103 24376 314FDP 103
288
292 257
264 .554" .554"
311
315 274
278 .582" .582"
314
318 278
282 .596" .596"
CUSTOM GROUND HYDRAULIC, SOLID, or ROLLER - Special order hydraulic All or solid lifter camshaft ground to your specifications. Call our technical support cid staff for personalized camshaft assistance.

Diagram 1. Follower Geometry (Sample based on intake of 24372)
Gross Lift
Note: The above solid profiles are ground with a smaller base circle than stock. If using stock length valves, you must use .100" thick lash caps (86127-8) in kit below. Check follower geometry with Dykem hi-spot blue or any other non-drying compound and adjust valve length accordingly (see diagram 1). Duration numbers @ .050" have been refigured to reflect valve lift. Note: Lift rule camshafts are available from Crower on a special order basis.

Remarks Springs Retainers Lash Caps Part No. Lifters 84105 66993-8 68324-8 87049-8 Hydraulic Lifter. 84206 66993-8 68324-8 87049-8 86127-8 Solid Lifter.
Spring pressure: 68324-8 Seat: 1.600" @ 118 lbs / Nose: 1.000" @ 283 lbs / Coil bind: 0.910" (Machine work, use cutter 68983*). Optional spring (stock diameter): 68147-8 Seat: 1.550" @ 78 lbs / Nose: 1.100" @ 177 lbs / Coil bind: 1.000" (Stock O.D. 1.369", no machine work). * Machine work required, specify 1132 pilot shaft when ordering. Note: Ford overhead camshafts are susceptible to lobe wear. We highly recommend breaking in new cam and followers with a light pressure break-in spring for a minimum of 30 minutes. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050").
Lobe Lift Rocker Ratio
Correct Contact surface
.334" x 1.66 = .554"
.334" x 1.57 = .524"
Lobe Lift
Rocker Ratio
Gross Lift
Wrong Valve or Lash Cap too short
.334" x 1.76 = .588"
Lobe Lift
Rocker Ratio
Gross Lift
Wrong Valve or Lash Cap too long
HYDRAULIC TO SOLID CONVERSION KITS

Part No. Remarks 76450-8 Comes with heavy duty adjusters, nuts, sleeves and stabilizer spring.
Note: When you achieve the indicated gross lift for your cam, the geometry and wear pattern are correct. Failure to achieve proper follower geometry will result in severe lobe wear.
74
HYDRAULIC CAMSHAFTS
240 300 Inline 6 Cylinder
Description
Gross Lift C.I.D. Part Grind Lobe Advertised Duration Duration @ .050" 1.6 / 1.6 Group Number Center Intake Exhaust Intake Exhaust Intake Exhaust
Ford
.411" .440" .448" .461"
MILEAGE COMPU-PRO / PERFORMANCE LEVEL 1 - Enhances mileage and torque in stock engines. RPM Power Range: Idle to 3500 / Redline: 4500 plus. POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power and mileage with extended rpms. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 - Hot street profile. Strong upper bottom and top end power. RPM Power Range: 1800 to 4500 / Redline: 6000 plus. ULTRA PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 - Hot street/drag. Strong mid-to-top end power. RPM Power Range: 2000 to 6000 / Redline: 6500 HYDRAULIC HAULER / PERFORMANCE LEVEL 4 - Hot street/drag profile with strong mid-range power. RPM Power Range: 2500 to 6500 / Redline: 6500 CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
All 19210 248HDP 112 cid All 19211 252HDP 112 cid All 19212 260HDP 112 cid All 19213 266HDP 112 cid All 19205 284HDP 110 cid All 00001 cid
248 252
254 258
184 192
192 .405" 196 .426"
260
268
202
210 .443"
266
274
210
213 .456"
284
290
220
222 .509"
.517"

Engineered Component Kit for the above part #'s: 84010
Note: Cam cores for 144, 170, 200 and 250 cid Ford engines are available from Crower on a special order basis. Note: These cams use .022" intake, .024" exhaust valve lash. Description
SOLID CAMSHAFTS
Gross Lift C.I.D. Part Grind Lobe Advertised Duration Duration @ .050" 1.6 / 1.6 Group Number Center Intake Exhaust Intake Exhaust Intake Exhaust
COMPU-PRO / PERFORMANCE LEVEL 5 - Fantastic high torque mid-range grind. RPM Power Range: 3000 to 6500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Explosive power throughout the power band. RPM Power Range: 3500 to 7000 plus. CUSTOM GROUND SOLID - Special order solid lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. CUSTOM GROUND ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
All 19311 274FDP cid 105 All 19312 284FDP cid 105 All 00000 cid All 00006 cid
274 284
280 290
238 248
242 .528" .539" 252 .558" .563"

Engineered Component Kit for the above part #'s: 84310
Note: Cam cores for 144, 170, 200 and 250 cid Ford engines are available from Crower on a special order basis.
Springs Retainers Seals Part No. Lifters 84010 66015-12 68305X1-12 87048-12 86072-12 84310 66915-12 68390X3-12 87048D-12 86072-12
Remarks Hydraulic Lifter. For rpm up to 6500 plus. Solid Lifter. For rpm up to 7000 plus.
Spring pressure: 68305X1-12 Seat: 1.700" @ 68 lbs / Nose: 1.200" @ 250 lbs / Coil bind: 1.050" (Stock OD, no machine work). 68390X3-12 Seat: 1.800" @ 115 lbs / Nose: 1.300" @ 331 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68971 pilot). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Description Part No. See pg. 180 Spring seat cutter Pg's. 146-149 Pushrods
Note: If exceeding 6500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower.
75
X-TREME MILEAGE CAMS AVAIL ABLE! CONTACT CROWER TECHNICIANS FOR MORE INFO.
Advertised Duration Gross Lift Grind Part Duration @ .050" 1.6 / 1.6 C.I.D. Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust
Ford
HYDRAULIC CAMSHAFTS
Non Roller 1963-1995 221 255 (4.2L) 260 289 302 V8
For engines that were originally equiped with a hydraulic flat tappet cam, retro fit hydraulic roller cams & kit are available, call CROWER for details.
BAJA BEAST / PERFORMANCE LEVEL 2 - Exhibits broad stump pulling power and torque. RPM Power Range: 1200 to 3800 / Redline: 5200 plus. TORQUE BEAST / PERFORMANCE LEVEL 3 - Delivers impressive mid-range and top end power. RPM Power Range: 2000 to 4800 / Redline: 6200 plus. POWER BEAST / PERFORMANCE LEVEL 3 - Emphasis on upper mid-range and top end power. RPM Power Range: 2000 to 4800 / Redline: 6200 plus. MILEAGE COMPU-PRO / PERFORMANCE LEVEL 1 - These cams enhance throttle response and low end torque while delivering fuel efficient motoring. RPM Power Range: Idle to 3500 / Redline: 4500 plus.
289 15915 302 289 15916 302 289 15917 302 289 15206 302 302 15207 cid 221 15208 289 302 15209 cid 221 15210 289 302 15211 cid 221 15212 289 302 15213 cid 302 15922 cid 302 15923 cid
258H 112 272H 112 288H 112 236HDP 112 246HDP 112 250HDP 112 260HDP 112 270HDP 112 276HDP 112 280HDP 112 284HDP 112 274HDP 108 290HDP 108
258 264
204
210
.443" .452"
272 279
210
220
.448" .474"
288 300
214
224
.474" .498"
236 246
180
184
.395" .400"
246 253
184
194
.402" .421"
POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power and mileage. Provides excellent low end and mid-range power with extended rpms for spirited offroad use. RPM Power Range: 1500 to 4000 / Redline: 5500 plus.
250 258
194
198
.422" .437"
260 266
204
210
.459" .464"
HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 - Intended for the hot marine/strip application, these cams offer extended rpm range with emphasis on upper bottom to top end power with strong mid-range. RPM Power Range: 1800 to 4500 / Redline: 6000 plus.
270 276
210
214
.464" .488"
276 281
212
216
.491" .500"
ULTRA PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 - Dual purpose hot street/strip camshaft. Delivers strong mid-range and top end torque and horsepower. RPM Power Range: 2000 to 6000 / Redline: 6500
280 286
220
226
.491" .502"
284 290
228
234
.513" .530"
HI-DRAULIC HAULER / PERFORMANCE LEVEL 4 - Lope at idle. Hot street/ strip cam with strong mid-range power. RPM Power Range: 2200 to 6200 plus. HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle with explosive upper bottom and mid-range torque. RPM Power Range: 2500 to 6500
274 284
220
228
.491" .512"
290 298
226
238
.502" .499"
Engineered Component Kit & Accessories listed on next page.
76
HYDRAULIC CAMSHAFTS (continued)

Non Roller 1963-1995 221 255 (4.2L) 260 289 302 V8
Ford
.507" .506" .536" .563" .486" .462"

HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle with explosive mid-range torque and acceleration. RPM Power Range: 2700 to 6000 HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle with explosive mid-range and top end horsepower. RPM Power Range: 3000 to 6500 TURBOMASTER - Intended for turbocharged hot street/strip and marine use. This cam offers extended rpm on mid-range and top end. RPM Power Range: 2000 to 6500 SUPERCHARGER - Designed for B&M/Roots type supercharged street/ strip and marine. Emphasis on upper bottom to top end power. RPM Power Range: 2400 to 6500 SUPERCHARGER - Dual purpose hot street/strip drag cam designed specifically to enhance B&M type blower. Good mid to top end power. RPM Power Range: 2600 to 6500 CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
302 15924 cid 302 15925 cid 289 15929 302 289 15930 302 289 15931 302 All 00001 cid
296HDP 108 304HDP 108 290HT 114 288HC 114 304HC 114
296 302
230
244
304 312
240
248
290 272
226
210
288 288
228
228
.464" .464"
304 304
246
246
.507" .507"
ENGINEERED COMPONENT KITS (see dia. 2)

Part No. 84013 84117 84118 84119 Lifters 66015-16 66015-16 66015-16 66015-16 Springs Retainers 68305X1-16 87048-16 68405-16 87048-16 68100X200-16 87048-16 68390X3-16 87048-16 Seals
Refer to page 7 for camshaft recommendation form ACCESSORIES

Part No. See pg. 180 Pg's. 146-149 Pg's.150-165 Pg's.150-165 See pg. 138 76523 See pg. 139 Description Spring seat cutter Pushrods Rocker arms (1.6) 38 Rocker arms (1.7) 38 Timing gear set Guide plates for 516 pushrod Distributor gear (.500" shaft dia)
Remarks For rpm up to 6000 max. Daily street use. 86072-16 For rpm up to 6500 plus. Limited street use. 86072-16 For rpm up to 6000 max. Daily street use. 86072-16 For rpm up to 6500 plus. Limited street use.
For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to the cam lobe and lifter surface. Specify X3 after corresponding component kit.
Spring pressure: 68305X1-16 Seat: 1.700" @ 68 lbs / Nose: 1.200" @ 250 lbs / Coil bind: 1.050" (Stock O.D., no machine work). Seat: 1.700" @ 110 lbs / Nose: 1.200" @ 297 lbs / Coil bind: 0.980" 68405-16 (Machine work, use cutter 68983*). 68100X200-16 Seat: 1.800" @ 107 lbs / Nose: 1.300" @ 254 lbs / Coil bind: 1.030" (Machine work, use cutter 68990*). 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.300" @ 331 lbs / Coil bind: 1.100" (Machine work, use cutter 68985*). Note: If your installed height does not fall withtin these dimensions, contact Crower for a recommendation. * Machine work required, specify 1132 pilot shaft when ordering. Note: If using Boss heads contact the Crower for special spring and retainer recommendations. Boss 302 engines employ a 1.73 rocker ratio, so the gross lifts will change for the Boss 302. To figure the correct gross lift for Boss 302 heads divide the gross lift listed by 1.6 (lobe lift) then multiply the lobe lift by 1.73 (Boss 302 rocker ratio). Note: Camshafts for 289/302 cid engines can be used in 351W engines by changing the firing order to 1-5-4-2-6-3-7-8. Some early Ford heads use 516 valve stems. Please specify when ordering as the above kits are designed for 1132 stems. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrod section or contact Crower.
SPRING INSTALLED HEIGHT

Diagram 1. Calculating Installed Spring Height
TOP OF KEEPER GROVE
BOTTOM OFFSPRING SEAT
Measure the height from top of keeper grove to bottom of spring seat. Refer to the height column of your retainer and add or subtract the amount given from the original overall measurement. Note: If heads have been extensively modified (machined spring pockets, longer valves, etc.) contact Crower for proper spring, keeper, cup and retainer recommendations. Have your keeper/seat measurement available.
77
Ford
HYDRAULIC ROLLER CAMSHAFTS

1963-1995 221 255 (4.2L) 260 289 302 (5.0L) & Boss 302 V8
PERFORMANCE LEVEL 1 - Launches hard with A.O.D. transmission. Torque all over the tach! Brutal bottom end. 302 cid / 2100 - 5300 rpm / Redline: 5800 rpm maximum PERFORMANCE LEVEL 2 - Big sound. Excellent 5-speed cam for heavy car. Strong low and mid-range torque. 302 cid / 2200 - 5500 rpm / Redline: 6000 rpm maximum PERFORMANCE LEVEL 2 - Most popular Ford hyd roller grind, blows away Chevrolets. Heavy mid-range. 302 cid / 2400 - 5700 rpm / Redline: 6200 rpm maximum PERFORMANCE LEVEL 3 - Big cid camshaft (320-347 cid) with higher compression, good cylinder heads and valve train components. 302 cid / 2600 - 6000 rpm / Redline: 6500 rpm maximum
See 15510 212HR212 275 114 Descrip See 15511 218HR224 278 114 Descrip See 15512 222HR228 282 112 Descrip See 15513 228HR234 288 112 Descrip
275
212
212
.531"
.531"
282
218
224
.468"
486"
286
222
228
.496"
512"
298
228
234
512"
531"
PERFORMANCE LEVEL 4 - Aggressive rpm camshaft, high stall A.O.D. or a See 15514 234HR240 298 110 Descrip 5-speed with low gears. For well prepared engines. 302 cid / 2700 - 6200 rpm / Redline: 6500 rpm maximum PERFORMANCE LEVEL 5 - Top end insanity for serious, professionally built engines only. 14 mile drag special. 302 cid / 3000 - 6300 rpm / Redline: 6500 rpm maximum CUSTOM GROUND HYDRAULIC ROLLER - Special order hydraulic roller lifter cam ground to your specifications. Call our technical support staff for personalized camshaft assistance. O.E.M. FACTORY STOCK SPECIFICATIONS 1989-1992 Ford Mustang 302 H.O. Engine equipped with Hydraulic Roller camshaft. SVO FACTORY STOCK SPECIFICATIONS #E-303 302 H.O. Engine equipped with Hydraulic Roller camshaft. SVO FACTORY STOCK SPECIFICATIONS #B-303 302 H.O. Engine equipped with Hydraulic Roller camshaft. See 15515 236HR242 300 110 Descrip All cid 00002
304
234
240
534"
545"
310
236
242
524"
529"

115 272 272 211 211 .437" .437"
Stock
E-303
110
220
220
.480"
.480"
B-303
110
224
224
.498"
.498"
Part No. Lifters Springs Retainers Keepers Remarks 84563 66335-16 68315-16 87048D-16 86107X2-8 & 86107-8 6000 max rpm. Daily street use. 84564 66335-16 68390X3-16 87048-16 86107X2-8 & 86107-8 6500 plus rpm. Limited street use.
Spring pressure: 68315-16 Seat: 1.800" @ 120 lbs / Nose: 1.300" @ 303 lbs / Coil bind: 1.175" (Stock O.D., no machine work). 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. Description See Spring See pg. 180 pg. 178 seat cutter Pg's. 146-149 PushrodsPushrods (516 diameter, 6.255" length) Pg's.150-165 Rocker arms (1.6) 38 Pg's.150-165 Rocker arms (1.7) 38 See pg. 138 Timing gear set Guide plates for 516 pushrod 76523 See pg. 139 Distributor gear (.500" shaft dia) Note: If exceeding 6500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower.
78
HYDRAULIC RETRO FIT ROLLER CAMSHAFTS

1963-1995 221 255 (4.2L) 260 289 302 & Boss 302 V8
Ford
214 .480" .480" 224 .468" 486" 228 .496" 512"

CONTACT CROWER TECHNICIANS FOR MORE INFO. Description (Note: See pages 8-9 for a detailed explanation of each Performance Level)
PERFORMANCE LEVEL 1 - Launches hard with A.O.D. transmission. Torque all over the tach! Brutal bottom end. 2100 - 5300 rpm / Redline: 5800 rpm maximum PERFORMANCE LEVEL 2 - Big sound. Excellent 5-speed cam for heavy car. Strong low and mid-range torque. 2200 - 5500 rpm / Redline: 6000 rpm maximum PERFORMANCE LEVEL 2 - Most popular Ford hyd roller grind, blows away Chevrolets. Heavy mid-range. 2400 - 5700 rpm / Redline: 6200 rpm maximum PERFORMANCE LEVEL 3 - Big cid camshaft (320-347 cid) with higher compression, good cylinder heads and valve train components. 2600 - 6000 rpm / Redline: 6500 rpm maximum
See 15520 210HR214 274 112 Descrip See 15521 218HR224 278 114 Descrip See 15522 222HR228 282 112 Descrip See 15523 228HR234 288 112 Descrip
278
210
282
218
286
222
298
228
234
512"
531"
PERFORMANCE LEVEL 4 - Aggressive rpm camshaft, high stall A.O.D. or a See 15524 234HR240 298 110 5-speed with low gears. For well prepared engines. Descrip 2700 - 6200 rpm / Redline: 6500 rpm maximum PERFORMANCE LEVEL 5 - Top end insanity for serious, professionally built engines only. 14 mile drag special. 3000 - 6300 rpm / Redline: 6500 rpm maximum CUSTOM GROUND HYDRAULIC ROLLER - Special order hydraulic roller lifter cam ground to your specifications. Call our technical support staff for personalized camshaft assistance. Cams also available in windsor firing order. See 15525 236HR242 300 110 Descrip All cid 00009
304
234
240
534"
545"
310
236
242
524"
529"
For engines which were manufactured with non-roller lifters, must be used with 66337-16 roller lifter.
Part No. Lifters Springs Retainers Keepers Remarks 84561 66337-16 68315-16 87048D-16 86107X2-8 & 86107-8 6000 max rpm. Daily street use. 84562 66337-16 68390X3-16 87048-16 86107X2-8 & 86107-8 6500 max rpm. Limited street use.
Spring pressure: 68315-16 Seat: 1.800" @ 120 lbs / Nose: 1.300" @ 303 lbs / Coil bind: 1.175" (Stock O.D., no machine work). 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). Note: Requires screw with studs & guide plates. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 Pg's.150-165 See pg. 139
Description Spring seat cutter Pushrods Rocker arms(1.6) 38 Bronze distributor gear
79
Ford
SOLID CAMSHAFTS
Non Roller 1963-1995 221 255 (4.2L) 260 289 302 (5.0L) & Boss 302 V8
PRO-STREET / PERFORMANCE LEVEL 2 - High torque grind with mid-range 289 15320 302 and top end power. Delivers mileage and horsepower. RPM Power Range: 2000 to 5500 / Redline: 6000 plus. PRO-STREET / PERFORMANCE LEVEL 3 - High torque grind with mid-range 289 15321 302 and top end power. RPM Power Range: 2200 to 6000 / Redline: 7000 plus. PRO-STREET / PERFORMANCE LEVEL 4 - High revving with superior midrange and top end power. RPM Power Range: 2500 to 7500 / Redline: 7500 plus. COMPU-PRO / PERFORMANCE LEVEL 4 - High torque, short oval camshaft. RPM Power Range: 2500 to 6000 / Redline: 7000 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Excellent high torque and midrange power oval track grind. RPM Power Range: 3000 to 7000 / Redline: 8000 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Upper mid-range and top end power for extra pop above 7000 rpm. RPM Power Range: 4500 to 7500 / Redline: 8000 plus. CUSTOM GROUND SOLID - Special order solid lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. 289 15322 302 289 15313 302 289 15314 302 289 15315 302 All 00000 cid
260FDP 114 282FDP 112 292FDP 110 274FDP 105 288FDP 105 302FDP 107
260
266
212
216
.450"
.453"
282
288
238
242
.478"
.488"
292
298
248
252
.499"
.512"
274 288
288 299
242 252
254 258
.542" .563"
.528" .579"
302
311
266
276
.605"
.619"

ACCESSORIES
Part No. Description See pg. 180 Spring seat cutter Pg's. 146-149 Pushrods Pg's.150-165 Rocker arms (1.6) 38 Pg's.150-165 Rocker arms (1.7) 38 See pg. 138 Timing gear set 76523 Guide plates for 516 pushrod See pg. 139 Distributor gear (.500" shaft dia)
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrod section or contact Crower.
TOP OF KEEPER GROVE
ENGINEERED COMPONENT KITS (see dia. 2)

Part No. Lifters 84213 66915-16 84217 66915-16 84218 66915-16 84219 66915-16 Springs Retainers Seals Remarks For rpm up to 6000 max. Daily street use. 68305X1-16 87048-16 87048-16 86072-16 For rpm up to 7000 plus. Limited street use. 68405-16 68100X200-16 87048-16 86072-16 For rpm up to 6500 max. Daily street use. 68390X3-16 87048-16 86072-16 For rpm up to 7500 plus. Limited street use.
Spring pressure: 68305X1-16 Seat: 1.700" @ 68 lbs / Nose: 1.200" @ 250 lbs / Coil bind: 1.050" (Stock O.D., no machine work). 68405-16 Seat: 1.700" @ 110 lbs / Nose: 1.200" @ 297 lbs / Coil bind: 0.980" (Machine work required, use 68985 cutter & 68972 pilot). 68100X200-16 Seat: 1.800" @ 107 lbs / Nose: 1.300" @ 254 lbs / Coil bind: 1.030" (Machine work required, use 68985 cutter & 68972 pilot). 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.300" @ 331 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). Note: If keeper height is longer or shorter than correct height ( .050" tolerance), contact Crower for a recommendation. Note: If using Boss heads contact the factory for special spring and retainer recommendations. Boss 302 engines employ a 1.73 rocker ratio, so the gross lifts will change for the Boss 302. To figure the correct gross lift for Boss 302 heads divide the gross lift listed by 1.6 (lobe lift) then multiply the lobe lift by 1.73 (Boss 302 rocker ratio). Note: Camshafts for 289/302 cid engines can be used in 351W engines by changing the firing order to 1-5-4-2-6-3-7-8. Some early Ford heads use 516 valve stems. Please specify when ordering as the above kits are designed for 1132 stems. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
Measure the height from top of keeper grove to bottom of spring seat. Refer to the height column of your retainer and add or subtract the amount given from the original overall measurement.
Diagram 1. Calculating Installed Spring Height
BOTTOM OFFSPRING SEAT
Note: If heads have been extensively modified (machined spring pockets, longer valves, etc.) contact Crower for proper spring, keeper, cup and retainer recommendations. Have your keeper/seat measurement available.
80
Mechanical 1963-1995 221 255 (4.2L) 260 289 302 (5.0L) & Boss 302 V8
ROLLER CAMSHAFTS
Ford
242 .528" .530" 260 .597" .578" 266 .606" .600"
STREET ROLLER / PERFORMANCE LEVEL 4 - Excellent street/strip profile. RPM Power Range: 2500 to 6000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - High torque oval track and drag race profile. RPM Power Range: 3000 to 7000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Fast 3/8 to 1/2 mile super oval track profile. RPM Power Range: 4000 to 7500 / Redline: 8000 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 5200 to 8000 / Redline: 8250 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 5500 to 8000 / Redline: 8250 plus. CUSTOM ORDER ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
289 15415 302 289 15416 302 289 15417 302 289 15418 302 289 15419 302 All 00002 cid
280R 112 285R 106 292R 106 300R 108 316R 110
280 288
232
285 292
254
292 302
256
300 310
268
274
.680" .669"
316 324
282
284
.702" .682"
A. These high lift cams require longer stem valves and higher spring pressure. Please contact Crower for properly engineered valvetrain.
Springs Retainers Seals Remarks Part No. Lifters 84510 66215-16 68390X3-16 87048-16 86072-16 For rpm up to 7500 max. Limited street use. 84513 66215-16 68380X2-16 87048-16 86072-16 For rpm up to 8000 plus. Race only.
Spring pressure: 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). 68380X2-16 Seat: 1.800" @ 197 lbs / Nose: 1.200" @ 470 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). Optional springs (race only): Seat: 1.900" @ 212 lbs / Nose: 1.200" @ 560 lbs / Coil bind: 1.100" 68363-16 (Machine work required, use 68985 cutter & 68972 pilot). 68670S-16 Seat: 1.900" @ 180 lbs / Nose: 1.200" @ 654 lbs / Coil bind: 1.010" (Machine work required, use 68985 cutter & 68972 pilot). Note: If using Boss heads contact the factory for special spring and retainer recommendations. Boss 302 engines employ a 1.73 rocker ratio, so the gross lifts will change for the Boss 302. To figure the correct gross lift for Boss 302 heads divide the gross lift listed by 1.6 (lobe lift) then multiply the lobe lift by 1.73 (Boss 302 rocker ratio). Note: Camshafts for 289/302 cid engines can be used in 351W engines by changing the firing order to 1-5-4-2-6-3-7-8. Some early Ford heads use 516 valve stems. Please specify when ordering as the above kits are designed for 1132 stems. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
HIPPO Note: For severe duty roller lifter applications, we highly recommend using our roller lifters with Hippo High Pressure Pin Oiling. Specify H in the part number. Ex. 66290X874H-16
ACCESSORIES
Note: If exceeding 8000 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower.
81
Ford
ROLLER CAMSHAFTS (continued)

Mechanical 1963-1995 221 255 (4.2L) 260 289 302 (5.0L) & Boss 302 V8
STREET ROLLER / PERFORMANCE LEVEL 4 - Excellent street/strip profile. RPM Power Range: 2500 to 6000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - High torque oval track and drag race profile. RPM Power Range: 3000 to 7000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Fast 3/8 to 1/2 mile super oval track profile. RPM Power Range: 4000 to 7500 / Redline: 8000 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 5200 to 8000 / Redline: 8250 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 5500 to 8000 / Redline: 8250 plus. CUSTOM ORDER ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
289 15415 302 289 15416 302 289 15417 302 289 15418A 302 289 15419A 302 All 00002 cid
280R 112 285R 106 292R 106 300R 108 316R 110
280 288
232
242
.528" .530"
285 292
254
260
.597" .578"
292 302
256
266
.606" .600"
300 310
268
274
.680" .669"
316 324
282
284
.702" .682"
A. These high lift cams require longer stem valves and higher spring pressure. Please contact Crower for properly engineered valvetrain.

Springs Retainers Seals Remarks Part No. Lifters 84510 66215-16 68390X3-16 87048-16 86072-16 For rpm up to 7500 max. Limited street use. 84513 66215-16 68380X2-16 87048-16 86072-16 For rpm up to 8000 plus. Race only. For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to the cam lobe and lifter surface. Specify X3 after corresponding component kit.
Spring pressure: 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). 68380X2-16 Seat: 1.800" @ 197 lbs / Nose: 1.200" @ 470 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). Optional springs (race only): Seat: 1.900" @ 212 lbs / Nose: 1.200" @ 560 lbs / Coil bind: 1.100" 68363-16 (Machine work required, use 68985 cutter & 68972 pilot). 68670S-16 Seat: 1.900" @ 180 lbs / Nose: 1.200" @ 654 lbs / Coil bind: 1.010" (Machine work required, use 68985 cutter & 68972 pilot). Note: If using Boss heads contact the factory for special spring and retainer recommendations. Boss 302 engines employ a 1.73 rocker ratio, so the gross lifts will change for the Boss 302. To figure the correct gross lift for Boss 302 heads divide the gross lift listed by 1.6 (lobe lift) then multiply the lobe lift by 1.73 (Boss 302 rocker ratio). Note: Camshafts for 289/302 cid engines can be used in 351W engines by changing the firing order to 1-5-4-2-6-3-7-8. Some early Ford heads use 516 valve stems. Please specify when ordering as the above kits are designed for 1132 stems. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Note: If exceeding 8000 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower.
82
Non Roller 1969-1993 351W (5.8 L), 1982-1984 302 (5.0L), 302 SVO & 351 SVO
HYDRAULIC CAMSHAFTS
Ford
Rec Kit

BAJA BEAST / PERFORMANCE LEVEL 2 - Exhibits broad stump pulling 351 15935 power and torque. RPM Power Range: 1200 - 3800 / Redline: 5200 plus. POWER BEAST / PERFORMANCE LEVEL 4 - Delivers impressive midrange and top end power. Healthy sound. Economical price. RPM Power Range: 1750 - 6000 / Redline: 6500 351 15903
258H 112 298H 112
258
264 202
210 .438"
.446" 84125
298
304 224
234 .498"
.520" 84125
MILEAGE COMPU-PRO / PERFORMANCE LEVEL 1 - Enhances mileage 351 15224 250HDP 250 and torque in stock engines. 112 RPM Power Range: Idle to 3500 / Redline: 4500 plus. POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power and mileage with extended rpms. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 - Hot street/strip grind with emphasis on upper bottom to top end power. RPM Power Range: 1800 to 4500 / Redline: 6000 plus. ULTRA PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 Street/strip grind with strong mid to top end power. RPM Power Range: 2200 to 6000 / Redline: 6500 plus. 351 15233 270HDP 270 112 351 15236 280HDP 280 112 351 15237 297HDP 297 112
258 192
198 .426"
.430" 84125
276 212
218 .475"
.489" 84125
286 220
226 .488"
.501" 84125
308 236
242 .538"
.534" 84125

Part No. Lifters Springs Retainers Seals Remarks 84125 66015-16 68100X200-16 87048-16 86072-16 68951-16 6000 rpm max. Daily street use. 84126 66015-16 68390X3-16 87048-16 86072-16 68951-16 6500 rpm max. Limited street use. For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to the cam lobe and lifter surface. Specify X3 after corresponding component kit. Spring pressure: 68100X200-16 Seat: 1.800" @ 107 lbs / Nose: 1.300" @ 254 lbs / Coil bind: 1.030" (Stock O.D., no machine work). 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Stock O.D., no machine work). Note: To eliminate using seat cups, you can machine heads with cutter 68990 (84125) or 68985 (84126). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. See pg. 178 See pg. 146 Pg's. 150-165
Description Spring seat cutter Pushrods Rocker arms (1.6) 38
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower.
83
Ford


Rec Kit
HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle. Explosive mid-range torque. RPM Power Range: 2500 to 6500 HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Violent mid-range acceleration and torque. RPM Power Range: 2700 to 6500. HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle. Explosive mid-range acceleration and torque. RPM Power Range: 3000 to 6500 TURBOMASTER - This cam provides excellent low end and mid-range power with extended rpm range plus mileage for spirited offroad use. RPM Power Range: 1800 to 5500 plus. TURBOMASTER - Intended for turbocharged hot street/strip and marine use. This cam offers extended rpms on upper bottom and top. RPM Power Range: 2000 to 6500 SUPERCHARGER - Designed for B&M/Roots type supercharged street/ strip and marine applications. Emphasis on mid to top end. RPM Power Range: 2400 to 6500 CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
351 15254 84HDP 108
284
294 224
232 .498"
.501" 84125 84125 or 84126 84125 or 84126 84125 or 84126 84125 or 84126 84125 or 84126
351 15255 296HDP 296 108 351 15256 304HDP 304 108 351 15938 278HT 114 290HT 114 278
304 230
246 .506"
.506"
312 242
250 .536"
.506"
260 212
200 .466"
.430"
351 15939
290
272 226
210 .486"
.462"
351 15940 288HC 114 00001
288
288 226
226 .467"
.467"

Part No. Lifters Springs Retainers Seals Remarks 84125 66015-16 68100X200-16 87048-16 86072-16 68951-16 6000 rpm max. Daily street use. 84126 66015-16 68390X3-16 87048-16 86072-16 68951-16 6500 rpm max. Limited street use. For severe duty applications, Crower recommends using our solid lifter with the added "coolface oiling option". Specify X980 after corresponding component kit. Spring pressure: 68100X200-16 Seat: 1.800" @ 107 lbs / Nose: 1.300" @ 254 lbs / Coil bind: 1.030" (Stock O.D., no machine work). 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Stock O.D., no machine work). Note: To eliminate using seat cups, you can machine heads with cutter 68990 (84125) or 68985 (84126). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. Description See pg. 178 Spring seat cutter See pg. 146 Pushrods Pg's. 150-165 Rocker arms (1.6) 38
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower.
84
SOLID CAMSHAFTS
Ford
Rec Kit
PRO-STREET / PERFORMANCE LEVEL 3 - High torque profile with emphasis on mid-range and top end power. RPM Power Range: 2200 to 6000 / Redline: 6500 plus. PRO-STREET / PERFORMANCE LEVEL 4 - High revving profile with superior mid-range and top end power. RPM Power Range: 2500 to 6500 / Redline: 7000 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - High torque, high revving profile, perfect for short oval track applications. RPM Power Range: 3500 to 6500 / Redline: 7000 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - High torque, high revving profile, perfect for midsize oval track applications. RPM Power Range: 4000 to 7000 / Redline: 7500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Emphasis on mid-range and top end power for extra pop above 7000 rpm. RPM Power Range: 4500 to 7500 / Redline: 8000 plus.
351 15358 260FDP 112 351 15359 282FDP 112 351 15345 288FDP 105 351 15346 296FDP 106 351 15347 310FDP 108
260
264
228 226 .474" .485" 84218
282
288
242 250 .538" .557" 84219
288
299
252 258 .562" .579" 84219
296
306
260 268 .586" .605" 84219
310
316
276 278 .622" .629" 84219
CUSTOM GROUND SOLID - Special order solid lifter camshaft ground 351 00000 to your specifications. Call our technical support staff for personalized camshaft assistance.
84218 or 84219
Part No. Lifters Springs Retainers 84218 66915-16 68100X200-16 87048-16 84219 66915-16 68390X3-16 87048-16
Seals 86072-16 86072-16
Remarks 6500 max. Daily street use. 7500 max. Limited street use.
Spring pressure: 68100X200-16 68390X3-16
Seat: 1.800" @ 107 lbs / Nose: 1.300" @ 254 lbs / Coil bind: 1.030" (Machine work, use cutter 68990). Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Machine work, use cutter 68985).
ACCESSORIES
Part No. See pg. 178 See pg. 146
Description Spring seat cutter Pushrods
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower. Note: If exceeding 7500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower.
85
Ford
ROLLER CAMSHAFTS
Mechanical 1969-1993 351W (5.8 L), 1982-1984 302 (5.0L), 302 SVO & 351 SVO
Rec Kit
PRO-STREET / PERFORMANCE LEVEL 4 - Perfect for street/strip. Emphasis on mid-range power. RPM Power Range: 2500 to 6500 / Redline: 7000 plus. PRO-STREET / PERFORMANCE LEVEL 5 - Perfect for street/strip. Emphasis on mid-range and top end power. RPM Power Range: 3500 to 7000 / Redline: 7000 plus.
351 15458
280R 112 290R 110 285R 106 300R 107 309R 108
280
288
232
242 .528"
.530" 84510
351 15459
290
296
248
252 .558"
.547" 84510
COMPU-PRO / PERFORMANCE LEVEL 5 - Emphasis on mid-range and 351 15445 top end, excellent drag profile. RPM Power Range: Varies on valve train, heads, manifold, etc... COMPU-PRO / PERFORMANCE LEVEL 5 - Emphasis on mid-range and 351 15446 top end, excellent drag profile. RPM Power Range: Varies on valve train, heads, manifold, etc... COMPU-PRO / PERFORMANCE LEVEL 5 - Emphasis on mid-range and 351 15447 top end, excellent drag profile. RPM Power Range: Varies on valve train, heads, manifold, etc... CUSTOM GROUND ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. CUSTOM GROUND MECHANICAL ROLLER - Special order roller lifter camshaft ground to your specifications. Call with all engine data including head flow data, valve sizes, operating power range, etc. 351 00002 00003 351 00060
285
292
254
260 .597"
.578" 84513
300
310
268
274 .680"
669" 84509
314
276
282 .685"
.656" 84509
Refer to page 7 for camshaft recommendation form Refer to page 7 for camshaft recommendation form
84513 or 84509

Part No. 84510 84513 84509 Lifters Springs 66215-16 68390X3-16 66215-16 68380X2-16 66215-16 68670S-16 Retainers Seals Keepers 87048-16 86072-16 87048-16 86072-16 86067D-16 86072-16 86110-16 Remarks 7000 rpm. Limited street use. 8000 rpm. Race only. 8500 rpm. Race only.
Spring pressure: 68390X3-16 Seat: 1.800" @ 115 lbs / Nose: 1.250" @ 355 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). 68380X2-16 Seat: 1.800" @ 197 lbs / Nose: 1.200" @ 470 lbs / Coil bind: 1.110" (Machine work required, use 68985 cutter & 68972 pilot). 68670S-16 Seat: 1.900" @ 196 lbs / Nose: 1.200" @ 654 lbs / Coil bind: 1.010" (Machine work required, use 68985 cutter & 68972 pilot).
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 Pg's.150-165 See pg. 139 Description Spring seat cutter Pushrods Rocker arms(1.6) 38 Bronze distributor gear
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower. Note: If exceeding 7500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower. HIPPO Note: For severe duty roller lifter applications, we highly recommend using our roller lifters with Hippo High Pressure Pin Oiling. Specify H in the part number. Ex. 66290X874H-16
86
HYDRAULIC CAMSHAFTS
Description (Note: See pages 8-9 for a detailed explanation of each Performance Level) Note: These cams use .000" intake and exhaust valve lash.
Non Roller 1970-1982 351C 351M 400 V8
Ford
Rec Kit
BAJA BEAST / PERFORMANCE LEVEL 2 - Exhibits broad stump pulling 351 15965 power and torque. Good for stock replacement. 400 RPM Power Range: 1200 to 3800 / Redline: 5200 plus. TORQUE BEAST / PERFORMANCE LEVEL 2 - Delivers impressive mid-range and top end power. RPM Power Range: 2000 to 4800 / Redline: 6000 plus. POWER BEAST / PERFORMANCE LEVEL 3 - Exhibits broad stump pulling power and torque. Good for stock replacement. RPM Power Range: 2200 to 5000 / Redline: 6200 plus. ULTRA BEAST / PERFORMANCE LEVEL 3 - Delivers impressive midrange and top end power. RPM Power Range: 2200 to 5000 / Redline: 6200 plus. MILEAGE COMPU-PRO / PERFORMANCE LEVEL 1 - These cams enhance throttle response and low end torque while delivering fuel efficient motoring. RPM Power Range: Idle to 3500 / Redline: 4500 plus. 351 15975 400 351 15973 400 351 15966 400
258H 112 282H 112 292H 112 278H 112
258
264 200
210 .477"
.486" 84125
282
292 204
214 .486"
.512" 84125
292
302 214
224 .512"
.538" 84125
278
284 220
226 .529"
.540" 84125
351 15229 250HDP cid 112 400 15230 260HDP cid 112
250
258 192
196 .460"
.465" 84125
260
266 204
210 .481"
.488" 84125
POWER COMPU-PRO / PERFORMANCE LEVEL 2 351 15240 270HDP - Perfect combination of power and mileage. Provides excellent low cid 112 end and mid-range power with extended rpms for spirited offroad use. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. 400 15241 276HDP cid 112 HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 - Intended for the hot marine/strip application, these cams offer an extended rpm range with upper bottom and top end power with strong emphasis on mid-range. RPM Power Range: 1800 to 4500 / Redline: 6000 plus. 351 15242 280HDP cid 112 400 15243 284HDP cid 112 351 15244 297HDP cid 112 400 15245 311HDP cid 112
270
276 210
220 .486"
.510" 84125 84125 or 84124 84125 or 84124 84125 or 84124 84125 or 84124 84125 or 84124
276
281 214
220 .527"
.534"
280
286 220
226 .526"
.540"
284
290 228
234 .557"
.574"
ULTRA PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 - Dual purpose hot street/strip camshaft. Delivers strong mid-range and top end torque and horsepower. RPM Power Range: 2000 to 6000 / Redline: 6500
297
308 234
240 .578"
.578"
311
316 246
252 .593"
.606"

Part No. Lifters Springs Retainers Seals Remarks 84125 66015-16 68100X200-16 87048-16 86072-16 68951-16 6000 rpm max. Daily street use. 6500 rpm max. Limited street use. 84124 66015-16 68315-16 87050-16 86072-16 For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to the cam lobe and lifter surface. Specify X3 after corresponding component kit. Spring pressure: 68100X200-16 Seat: 1.800" @ 107 lbs / Nose: 1.250" @ 274 lbs / Coil bind: 1.030" 68315-16 Seat: 1.850" @ 105 lbs / Nose: 1.250" @ 322 lbs / Coil bind: 1.150" (Stock O.D.) Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. Pg's. 146-149 Pg's.150-165 Pg's.150-165 See pg. 139 Description Pushrods Rocker arms (1.73) 7/16 Rocker arms (1.8) 7/16 Timing gear set
Note: If using guide plates, heat-treated pushrods (RC60 series) are required. See pushrod section or contact Crower.
87
Ford

Non Roller 1970-1982 351C 351M 400 V8
Rec Kit Advertised Duration Gross Lift Grind Part Duration @ .050" 1.73 / 1.73 C.I.D. Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust
HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle with explosive upper bottom and mid-range torque. RPM Power Range: 2500 to 6000 plus. HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Strong idle with violent mid-range acceleration and torque. RPM Power Range: 2700 to 6500
351 15266 280HDP cid 108 351 15267 290HDP cid 108
280
288 222
230 .540"
.540" 84125 or 84124 .543" 84125 or 84124 .545" 84125 or 84124 .548" 84125 or 84124 84125 or 84124
290
302 238
248 .536"
HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Very rough idle with 351 15268 302HDP violent mid-range and top end acceleration and power. 400 108 RPM Power Range: 3000 to 6500 cid SUPERCHARGER - Designed for B&M/Roots type supercharged street/ strip and marine applications. Emphasis on mid to top end. RPM Power Range: 2400 to 6500 CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. 351 15981 400 cid All cid 304HC 114
302
312 244
248 .548"
304
304 246
246 .548"
390 SERIES HYDRAULIC CAMSHAFTS

C.I.D. Group Low RPM RPM Range Peak Peak Torque HP Top RPM Part Number Advertised Duration @ .050" Duration @ .200" Lobe Duration Exhaust Intake Exhaust Center Intake Exhaust Intake Gross Lift 1.73 / 1.73 Lobe Lift Exhaust Intake Exhaust Intake
351C cid 400 cid 351C cid 400 cid 351C cid 400 cid 351C cid 400 cid 351C cid 400 cid 351C cid 400 cid 351C cid 400 cid
1800 1500 2000 1600 2100 1800 2300 2000 2400 2100 2500 2300 2600 2500
3300 5000 5500 3000 4500 5000 3500 5300 5800 3100 4800 5300
15170 15171
112 112 112 110 110 108 108
264 269 277 280 289 298 304
272 202 278 207 283 215 287 219 295 227 303 236 310 242
210 216 221 225 233 241 248
112 116 126 131 140 149 156
115 125 130 134 142 150 158
.282" .287" .300" .306" .318" .332" .344"
.280" .292" .297" .303" .316" .328" .340"
.488" .497" .519" .530" .550" .574" .595"
.484" .505" .514" .524" .547" .567" .588"
3600 5500 6000 15172 3300 5000 5500 3800 5700 6300 15173 3500 5200 5700 3900 5900 6400 15174 3600 5500 6000 4000 6100 6500 15175 3800 5800 6300 4100 6300 6500 15176 4000 6000 6500 00001
CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications.

ACCESSORIES
Part No. Pg's. 146-149 Pg's.150-165 Pg's.150-165 See pg. 139 Description Pushrods Rocker arms (1.73) 7/16 Rocker arms (1.8) 7/16 Timing gear set

Part No. Lifters Springs Retainers Seals Remarks 84125 66015-16 68100X200-16 87048-16 86072-16 68951-16 6000 rpm max. Daily street use. 6500 rpm max. Limited street use. 84124 66015-16 68315-16 87050-16 86072-16 For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to the cam lobe and lifter surface. Specify X3 after corresponding component kit. Spring pressure: 68100X200-16 Seat: 1.800" @ 107 lbs / Nose: 1.250" @ 274 lbs / Coil bind: 1.030" 68315-16 Seat: 1.850" @ 105 lbs / Nose: 1.250" @ 322 lbs / Coil bind: 1.150" (Stock O.D.) Valve timing events are available online at: www.crower.com/valvtime.html
Note: If using guide plates, heat-treated pushrods (RC60 series) are required. See pushrod section or contact Crower.
88
SOLID CAMSHAFTS
Non Roller 1970-1982 351C 351M 400 V8
Ford
Rec Kit
PRO-STREET / PERFORMANCE LEVEL 3 - High torque grind with mid- 351 15388 282FDP 282 range and top end power. 400 112 RPM Power Range: 2200 to 5750 / Redline: 6000 plus. PRO-STREET / PERFORMANCE LEVEL 4 - High revving with superior mid-range and top end power. RPM Power Range: 2500 to 6000 / Redline: 6250 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - High torque, short oval camshaft. RPM Power Range: 3500 to 6500 / Redline: 7000 plus. 351 15389 292FDP 292 400 112
288 238 242
.524"
.533" 84225
298 246 250
.541"
.548" 84225
351 15380 288FDP 288 400 105
294 254 258 306 262 268
.569" .592"
.580"
84225 or 84226
COMPU-PRO / PERFORMANCE LEVEL 5 - Great high torque oval track 351 15381 298FDP 298 grind with emphasis on mid-range power. 400 106 RPM Power Range: 4000 to 7000 / Redline: 7500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Upper mid-range and top end power for extra pop above 7000 rpm. RPM Power Range: 4500 to 7500 / Redline: 8000 plus. CUSTOM GROUND SOLID - Special order solid lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. 351 15382 311FDP 311 400 107 351 00000 400
.607" 84226
316 274 282
.618"
.638" 84226
See Below

Part No. Lifters Springs Retainers Seals Remarks 84225 66915-16 68100X200-16 87048-16 86072-16 68951-16 Solid Lifter. 6500 rpm max. Daily street use. 84226 66915-16 68390X3-16 87048-16 86072-16 68951-16 Solid Lifter. 7500 rpm max. Limited street use. For severe duty applications, Crower recommends using our solid lifter with the added "coolface oiling option". Specify X980 after corresponding component kit. Spring pressure: 68100X200-16 Seat: 1.825" @ 100 lbs / Nose: 1.325" @ 247 lbs / Coil bind: 1.030" (Seat cups eliminate machine work). 68390X3-16 Seat: 1.825" @ 106 lbs / Nose: 1.325" @ 310 lbs / Coil bind: 1.110" (Seat cups eliminate machine work). Note: Some stock cylinder heads come with multi-groove keepers on the exhaust. If so, you must order retainer 87049-16 which is designed to fit multi-groove keepers. See retainer specs or contact Crower. Note: If you machine heads to eliminate use of spring cups, see seat cutters or contact Crower. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 Pg's.150-165 Pg's.150-165 See pg. 138 Description Spring seat cutter Pushrods Rocker arms (1.73) 7/16 Rocker arms (1.8) 7/16 Timing gear set
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower. Note: If exceeding 7500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower.
89
Ford
ROLLER CAMSHAFTS
Mechanical 1970-1982 351C 351M 400 V8
STREET ROLLER / PERFORMANCE LEVEL 4 - Excellent street/strip profile. RPM Power Range: 2500 to 6000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - High torque oval track profile. RPM Power Range: 3000 to 7000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Fast 3/8 to 1/2 mile super oval track profile. RPM Power Range: 4000 to 7500 / Redline: 8000 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 5200 to 8000 / Redline: 8250 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 5500 to 8000 / Redline 8250 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Top end drag profile with plenty of power. RPM Power Range: 5200 to 8000 / Redline: 8250 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Top end drag profile with plenty of power. RPM Power Range: 5500 to 8000 / Redline: 8250 plus. CUSTOM GROUND ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. Custom Ground Mechanical Roller: part # 00060
All 15480 cid All 15481 cid All 15482 cid All 15483 cid All 15484 cid All 15485 cid All 15486 cid All 00002 cid 00060
284R 110 285R 106 297R 106 304R 106 311R 108 319R 110 334R 112
275 285 297
284 292 304
234 244 .570" 252 260 .645" 262 268 .662"
.572" .626" .636"
304
312
270 276 .690"
.672"
311
318
280 284 .759"
.736"
319
324
288 292 .795"
.736"
334
338
294 302 .783"
.724"

Springs Part No. Lifters Retainers Seals Remarks 84520 66218-16 68340-16 87062S-16 86072-16 86107X1-16 7500 rpm plus. 84521 66218-16 68363-16 87062-16 86072-16 86107X1-16 8000 rpm. Race only. Spring pressure: 68340-16 Seat: 1.875" @ 128 lbs / Nose: 1.350" @ 359 lbs / Coil bind: 1.080" (Machine work, use cutter 68986*). 68363-16 Seat: 1.900" @ 212 lbs / Nose: 1.200" @ 560 lbs / Coil bind: 1.100" (Machine work, use cutter 68992*). Optional spring (race only): 68555X1-16 Seat: 2.000" @ 239 lbs / Nose: 1.100" @ 870 lbs / Coil bind: 1.020" (Machine work, use cutter 68980*). * Machine work required, specify 1132 pilot shaft when ordering. Note: For high performance applications, we recommend using single groove valves and valve stem keepers. The above kits are designed for 1132 single groove valve stems and 7 and 10 single groove keepers. Race applications must use .100" long valves. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 See pg. 138 Pg's.150-165
Description Spring seat cutter Pushrods Timing gear set Rocker arms (1.73) 716
AVAILABLE CAM JOURNAL SIZES

Description
Stock Ford Bearing Size - Journal 1 = 2.080", 2 = 2.065", 3 = 2.050", 4 = 2.035", 5 = 2.020" Large Roller Bearing - Journal 1, 2, 3, 4 = 2.165", Journal 5 = 1.968" Roller Bearing (Ford Motorsport / SVO) - All Journals = 2.051" Babbit Bearing (Standard SVO) - All Journals = 2.081" To order the above cores specify #00003. 60mm is available on special order basis only (#00060). Special Firing Orders also available.
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower. Note: If exceeding 7500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower. Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower. HIGH RPM! Crower highly recommends the use of rollerized rockers. See rockers for ratios and stud diameters.
90

Non Roller 1963-1976 332 352 360 390 406 410 427 428 V8 FE
HYDRAULIC CAMSHAFTS
Ford
Rec Kit
BAJA BEAST / PERFORMANCE LEVEL 2 - Exhibits broad stump pulling power and torque. RPM Power Range: 1200 to 3800 / Redline: 5200 plus. POWER BEAST / PERFORMANCE LEVEL 3 - Delivers impressive midrange and top end power. Healthy sound. Economical price. RPM Power Range: 1200 to 3800 / Redline: 5200 plus. MILEAGE COMPU-PRO / PERFORMANCE LEVEL 1 - These cams enhance throttle response and low end torque while delivering fuel efficient motoring. RPM Power Range: Idle to 3500 / Redline: 4500 plus. POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power and mileage. Provides excellent low end and mid-range power with extended rpms for spirited offroad use. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 Intended for the hot marine/strip application, these cams offer extended rpm range with emphasis on upper bottom to top end power with strong mid-range. RPM Power Range: 1800 to 4500 / Redline: 6000 plus. ULTRA PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 Dual purpose hot street/strip camshaft. Delivers strong mid-range and top end torque and horsepower. RPM Power Range: 2000 to 6000 / Redline: 6500
332 16915 390 390 16903 428
268H 112 292H 112
268
274 204 210 .484"
.496" 84016
See Next Page for kit info. 292 302 214 224 .521" .547" 84116
See Next Page for kit info. 332 16236 246HDP 246 352 112 390 16237 250HDP 250 428 112 332 16238 260HDP 260 352 112 390 16239 270HDP 270 428 112 332 16240 276HDP 276 352 112 390 16241 280HDP 280 428 112 332 16242 284HDP 284 352 112 390 16243 297HDP 297 428 112 390 16255 280HDP 280 428 108 390 16256 290HDP 290 428 108 390 16257 302HDP 302 428 108 390 16979 428 390 16980 428 390 16981 428 All 00001 cid 290HT 114 288HC 114 304HC 114 290 253 186 192 .445" .466" 84016 See Next Page for kit info. 258 192 196 .468" .473" 84016 See Next Page for kit info. 266 204 210 .489" .500" 84016 See Next Page for kit info. 276 210 220 .494" .523" 84016 See Next Page for kit info. 281 214 220 .537" .543" 84016 See Next Page for kit info. 286 222 228 .538" .552" 84016 or See Next Page for kit info. 84116 .587" 84016 or See Next Page for kit info. 84116
290 228 230 .566"
308 236 242 .591" .588" 84116 See Next Page for kit info. 288 224 232 .549" .550" 84016 or See Next Page for kit info. 84116 .557" 84016 or See Next Page for kit info. 84116 .556" 84116
HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle. Explosive mid-range torque and power. RPM Power Range: 2500 to 6000 HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Violent mid- range acceleration and torque. RPM Power Range: 2700 to 6500 HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle. Explosive mid-range acceleration and torque. RPM Power Range: 3000 to 6500 TURBOMASTER - Intended for turbocharged hot street/strip and marine use. This cam offers extended rpms on upper bottom and top. RPM Power Range: 2000 to 6500 SUPERCHARGER - Designed for B&M/Roots type supercharged street/ strip and marine applications. Emphasis on mid-range to top. RPM Power Range: 2200 to 6500 SUPERCHARGER - Dual purpose hot street/strip cam designed to enhance B&M/Roots type supercharger. Strong mid to top end power. RPM Power Range: 2400 to 6500 CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
302 238 248 .550"
312 244 250 .554"
See Next Page for kit info. 280 224 212 .528" .502" 84016 or See Next Page for kit info. 84116 .533" 84116
288
288 226 226 .533"
See Next Page for kit info. 304 304 244 244 .556" .556" 84016
See Next Page for kit info.
See Next Page
91
Ford
Non Roller 1963-1976 332 352 360 390 406 410 427 428 V8 FE
Rec Kit
SOLID CAMSHAFTS
Note: These cams use .022" intake, .024" exhaust valve lash. Description Advertised Duration Gross Lift (Note: See pages 8-9 for a detailed explanation of each Grind Part Duration @ .050" 1.76 / 1.76 C.I.D. Performance Level) Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust
POWER BEAST / PERFORMANCE LEVEL 3 - Delivers impressive midrange and top end power. Healthy sound. Economical price. RPM Power Range: 1200 to 3800 / Redline: 5200 plus. PRO-STREET / PERFORMANCE LEVEL 3 - High torque grind with midrange and top end power. RPM Power Range: 2250 to 5500 / Redline: 6000 plus. PRO-STREET / PERFORMANCE LEVEL 4 - High revving with superior mid-range and top end power. RPM Power Range: 2500 to 6000 / Redline: 6500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - High torque, short oval camshaft. RPM Power Range: 2500 to 6000 / Redline: 7000 plus.
390 16360 428
284F 114
284
284 245
245 .524"
.524" 84316
390 16356 260FDP 428 114 390 16357 278FDP 428 114 390 16331 290FDP 428 108
260
266 228
228 .526"
.537" 84317
278
284 240
243 .530"
.535" 84317
290
298 247
252 .551"
.565" 84317 or 84316 .593" 84317 or 84316 .602" 84316
COMPU-PRO / PERFORMANCE LEVEL 5 - Great high torque mid-range 390 16332 300FDP 428 108 oval track grind. RPM Power Range: 3000 to 7000 / Redline: 7500. COMPU-PRO / PERFORMANCE LEVEL 5 - Strong mid-range and top end profile. RPM Power Range: 4000 to 7250 / Redline: 7500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Upper mid-range and top end power for extra pop above 7000 rpm. RPM Power Range: 4500 to 7500 / Redline: 7500 plus. CUSTOM GROUND SOLID - Special order solid lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. 390 16333 312FDP 428 108 390 16334 320FDP 428 110 All 00000 cid
300
310 255
260 .579"
312
318 263
272 .588"
320
328 273
281 .628"
.648"
84316 84317 or 84316

Part No. 84016S 84116 84317 84316 Lifters 66016-16 66016-16 66916-16 66916-16 Springs 68302X1-16 68340-16 68302X1-16 68340-16
Retainers Seals Remarks 87063M-16 Hydraulic. 6000 plus rpm. Daily street use. 87063-16 86071-16 Hydraulic. 6500 plus rpm. Limited street use. 87063M-16 86071-16 Solid. 6500 plus rpm. Daily street use. 87063-16 86071-16 Solid. 7500 plus rpm. Limited street use.
For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to the cam lobe and lifter surface. Specify X3 after corresponding component kit. For severe duty applications, Crower recommends using our solid lifter with the added "coolface oiling option". Specify X980 after corresponding component kit. Spring pressure: 68302X1-16 Seat: 1.850" @ 91 lbs / Nose: 1.350" @ 256 lbs / Coil bind: 1.150" (Stock O.D., no machine work). 68340-16 Seat: 1.900" @ 119 lbs / Nose: 1.350" @ 359 lbs / Coil bind: 1.080" (Machine work, use cutter 68986*). * Machine work required, specify 38 pilot shaft when ordering. Deep Seat Shell design lifter: Crower deep seated, solid lifters (Deep Seat Shell 66925-16) and pushrods (70138-16) insures proper valve train geometry. Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 See pg. 138 See pg. 139
Description Spring seat cutter Pushrods Timing gear set Distributor gear (.500" shaft dia)
Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower.
92
Mechanical 1963-1976 332 352 360 390 406 410 427 428 V8 FE
ROLLER CAMSHAFTS
Ford
.582" 84524 .655" 84524 or 84525 .663" 84525 .675" 84525 .675" 84525 .771" .783" Call Crower Call Crower See Below
Gross Lift Advertised Duration Rec 1.76 / 1.76 Grind Part Duration @ .050" C.I.D. Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust Kit
STREET ROLLER / PERFORMANCE LEVEL 4 - Excellent street/strip profile. RPM Power Range: 2500 to 6000 / Redline: 7500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - High torque oval track profile. RPM Power Range: 3750 to 7000 / Redline: 7500 plus.
390 16462 428 390 16463 428
280R 110 290R 108 296R 108 301R 108 306R 108 314R 110 318R 110
280 290
288 234 296 248
244 .580" 254 .651"
ULTRA-ACTION / PERFORMANCE LEVEL 5 - Strong mid-range design. 390 16464 428 RPM Power Range: 4000 to 7250 / Redline: 7750 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Fast 3/8 to 1/2 mile super oval track profile. RPM Power Range: 4250 to 7500 / Redline: 8000 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 4500 to 7750 / Redline: 8250 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag profile. RPM Power Range: 4750 to 8000 / Redline: 8500 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Fast top end power profile. RPM Power Range: 5000 to 8250 / Redline: 8750 plus. CUSTOM GROUND ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. 390 16465 428 390 16466 428 390 16467 428 390 16468 428 All 00002 cid
296 301 306 314 318
301 254 306 258 310 264 318 278 324 282
260 .654" 264 .663" 268 .675" 282 .752" 286 .770"

Part No. Lifters 84524 66216-16 84525 66216-16 Springs Retainers 68385X2-16 87063-16 68363-16 87063-16 Seals 86071-16 86071-16 Remarks 7000 plus rpm. Street use. 7500 plus rpm
Spring pressure: 68385X2-16 Seat: 1.900" @ 166 lbs / Nose: 1.300" @ 422 lbs / Coil bind: 1.100" (Machine work, use cutter 68979*). 68363-16 Seat: 1.900" @ 212 lbs / Nose: 1.200" @ 560 lbs / Coil bind: 1.100" (Machine work, use cutter 68992*). Optional spring (race only): * Machine work required, specify 38 pilot shaft when ordering. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Note: If exceeding 8000 rpm, high pressure springs and titanium retainers may be required. See spring and retainer specs or contact Crower for proper recommendations. Valve timing events are available online at: www.crower.com/valvtime.html
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 See pg. 138 Description Spring seat cutter Pushrods Timing gear set
Note: If using longer than stock valves you may require spring and retainer modifications. See specs or contact Crower.
93
Ford
Non Roller 1968-1994 370 429 460 V8
HYDRAULIC CAMSHAFTS
Rec Kit
BAJA BEAST / PERFORMANCE LEVEL 2 - Exhibits broad stump pulling power and torque. RPM Power Range: 1200 to 3800 / Redline: 5200 plus. POWER BEAST / PERFORMANCE LEVEL 3 - Low to mid-range torque for daily drivability. Economical price. RPM Power Range: 1200 to 3800 / Redline: 5200 plus. ULTRA BEAST / PERFORMANCE LEVEL 3 - Delivers impressive midrange and top end power. Economical price. RPM Power Range: 2000 to 4800 / Redline: 6200 plus. POWER COMPU-PRO / PERFORMANCE LEVEL 2 - Perfect combination of power and mileage. Provides excellent low end and mid-range power with extended rpms for spirited offroad use. RPM Power Range: 1500 to 4000 / Redline: 5500 plus. HIGH PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 3 Intended for the hot marine/strip application, these cams offer extended rpm range with emphasis on upper bottom to top end power with strong mid-range. RPM Power Range: 1800 to 4500 / Redline: 6000 plus. ULTRA PERFORMANCE COMPU-PRO / PERFORMANCE LEVEL 4 Dual purpose hot street/strip camshaft. Delivers strong mid-range and top end torque and horsepower. RPM Power Range: 2000 to 6000 / Redline: 7000 plus. HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Rough idle. Explosive mid-range torque. RPM Power Range: 2500 to 6500 plus.
370 22915 460 429 22903 460 460 22917 cid
268H 112 293H 112 268H 112
268
274 203
210 .481" .488" 84022
268
286 210
226 .510" .536" 84022
303
308 224
234 .538" .562" 84122
370 22239 270HDP 112 429 460 22240 276HDP 112 cid 370 22241 280HDP 112 429 460 22242 284HDP 112 cid 370 22243 297HDP 112 429 460 22244 311HDP 112 cid 429 22205 280HDP 108 460
270 274 280 284 297 311 280
276 211 281 215 286 220 290 227 308 237 316 246 288 222
218 .484" .509" 84022 221 .527" .535" 84022 226 .524" .541" 84022 232 .552" .569" 84022 84122 240 .580" .576" 84122 250 .588" .604" 84122 232 .536" .540" 84022 84122 245 .535" .545" 84022 84122 244 .541" .541" 84022 84122 Kits on Next Page
HI-DRAULIC HAULER / PERFORMANCE LEVEL 5 - Violent mid- range 429 22206 290HDP 108 acceleration and torque. 460 RPM Power Range: 2700 to 6700 plus. SUPERCHARGER - Dual purpose hot street/strip cam designed to enhance B&M/Roots type supercharger. Strong mid to top end power. RPM Power Range: 2400 to 6700 plus. CUSTOM GROUND HYDRAULIC - Special order hydraulic lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. 429 22981 304HC 114 460 All cid 00001
290
302 236
304
304 244

Part No. Lifters Springs 84022 66015-16 68302X1-16 84122 66015-16 68340-16
Spring pressure: 68302X1-16 Seat: 1.800" @ 107 lbs / Nose: 1.250" @ 292 lbs / Coil bind: 1.150" (Machine work, use cutter 68976). 68340-16 Seat: 1.900" @ 118 lbs / Nose: 1.300" @ 384 lbs / Coil bind: 1.080" (Machine work, use cutter 68986). Valve timing events are available online at: www.crower.com/valvtime.html
HIPPO Note: For severe duty roller lifter applications, we highly recommend Retainers Seals Remarks using our roller lifters with Hippo High 87062S-16 Hydraulic. 6500 max rpm. Daily street use. Pressure Pin Oiling. Specify H in the 87062-16 86072-16 Hydraulic. 6500 max rpm. Limited street use. part number. Ex. 66290X874H-16
Part No. Pg's. 146-149 Pg's. 150-165 Note: If using guide plates, heat-treated pushrods (RC60 series) Pg's. 150-165 are required. See pushrod section or contact Crower. See pg. 138
ACCESSORIES
Description Pushrods Rocker arms (1.73) 7/16 Rocker arms (1.8) 7/16 Timing gear set (1972-up)
94
390 SERIES HYDRAULIC CAMSHAFTS

Non Roller 1968-1994 370 429 460 V8
Ford
.488" .497" .519" .530" .550" .574" .595" .484" .505" .514" .524" .547" .567" .588"

C.I.D. Group Low RPM RPM Range Peak Peak Torque HP Top RPM Gross Lift Advertised Part Lobe Duration @ .050" Duration @ .200" 1.73 / 1.73 Lobe Lift Duration Number Center Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust Exhaust Intake
429 cid 460 cid 429 cid 460 cid 429 cid 460 cid 429 cid 460 cid 429 cid 460 cid 429 cid 460 cid 429 cid 460 cid
1500 1100 1700 1300 1900 1600 2100 1800 2300 2000 2500 2300 2700 2500
3000 4600 5100 2600 4100 4600 3200 4800 5300 2800 4300 4800 3400 5000 5500 3100 4600 5100 3600 5200 5700 3300 4800 5300 3800 5400 5900 3500 5000 5500 4000 5600 6100 3800 5200 5700 4200 5800 6300 4000 5400 5900
22170 112 22171 112 22172 112 22173 111 22174 110 22175 110 22176 108 00001
264 269 277 280 289 298 304
272 202 278 207 283 215 287 219 295 227 303 236 310 242
210 216 221 225 233 241 248
112 116 126 131 140 149 156
115 .282" 125 .287" 130 .300" 134 .306" 142 .318" 150 .332" 158 .344"
.280" .292" .297" .303" .316" .328" .340"
MARINE HYDRAULIC CAMSHAFTS

C.I.D. Group Low RPM RPM Range Peak Peak Torque HP Top RPM Gross Lift Advertised Part Lobe Duration @ .050" Duration @ .200" 1.73 / 1.73 Lobe Lift Duration Number Center Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust Exhaust Intake
429 cid 460 cid 429 cid 460 cid 429 cid 460 cid
1600 3100 4700 5200 1300 2800 4300 4800 2000 3500 5100 5600 1700 3200 4700 5200 2400 3900 5400 5900 2200 3700 5100 5600
22220 114 277 22221 114 289 22222 114 304 00001
283 295 310
215 227 242
221 233 248
126 140 156
130 142 158
.300" .318" .344"
.297" .519" .316" .550" .340" .595"
.484" .546" .588"

Part No. Lifters Springs 84022 66015-16 68302X1-16 84122 66015-16 68340-16 Retainers Seals Remarks 87062S-16 Hydraulic. 6500 max rpm. Daily street use. 87062-16 86072-16 Hydraulic. 6500 max rpm. Limited street use.
ACCESSORIES For severe duty applications, Crower offers a high-lube CamSaver lifter that channels more oil to Part No. Description the cam lobe and lifter surface. Specify X3 after corresponding component kit. See pg. 146 Pushrods Spring pressure: 73615-16 Rocker arms (1.73) 7/16 68302X1-16 Seat: 1.800" @ 107 lbs / Nose: 1.250" @ 292 lbs / Coil bind: 1.150" 73619-16 Rocker arms (1.8) 7/16 (Machine work, use cutter 68976). 76535 Timing gear set (1972-up) 68340-16 Seat: 1.900" @ 118 lbs / Nose: 1.300" @ 384 lbs / Coil bind: 1.080" (Machine work, use cutter 68986). Note: If using guide plates, heat-treated pushrods Valve timing events are available online at: www.crower.com/valvtime.html
(RC60 series) are required. See pushrod section or contact Crower. For technical support call 619-661-6477 Some products listed are not legal for sale or use on emission controlled motor vehicles RPM ranges vary upon application www.crower.com
95
Ford
Non Roller 1968-1994 370 429 460 V8
390 SERIES SOLID CAMSHAFTS
Advertised Duration Gross Lift Grind C.I.D. Part Duration @ .050" 1.73 / 1.73 Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust
ULTRA BEAST / PERFORMANCE LEVEL 4 - Delivers impressive mid-range and 429 22360 top end power. 460 RPM Power Range: 2750 to 6500 / Redline: 7000 plus. PRO-STREET / PERFORMANCE LEVEL 3 - High torque grind with mid-range and top end power. RPM Power Range: 2250 to 5500 / Redline: 6000 plus. PRO-STREET / PERFORMANCE LEVEL 4 - High revving with superior midrange and top end power. RPM Power Range: 2500 to 6000 / Redline: 6500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - High torque, short oval camshaft. RPM Power Range: 2500 to 6000 / Redline: 7000 plus.
317F 112
294
304 244 254 .588" .614"
429 22354 260FDP 460 112 429 22355 278FDP 460 110 429 22356 290FDP 460 108
260
266 228 228 .516" .533"
278
284 238 241 .519" .524"
290 300
298 247 251 .538" .552" 310 255 255 .569" .578"
COMPU-PRO / PERFORMANCE LEVEL 5 - Great high torque profile with mid- 429 22357 300FDP range power. 460 108 RPM Power Range: 3000 to 7000 / Redline: 7400 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Strong mid-range/top end profile. RPM Power Range: 4000 to 7250 / Redline: 7500 plus. COMPU-PRO / PERFORMANCE LEVEL 5 - Upper mid-range and top end power for extra pop above 7000 rpm. RPM Power Range: 4500 to 7500 / Redline: 7750 plus. CUSTOM GROUND SOLID - Special order solid lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance. CUSTOM GROUND MECHANICAL ROLLER - Special order roller lifter camshaft ground to your specifications. Call with all engine data including head flow data, valve sizes, operating power range, etc. 429 22358 312FDP 460 108 429 22359 320FDP 460 108 All 00000 cid
312 320
318 263 269 .590" .602" 328 273 279 .614" .633"
Refer to page 7 for camshaft recommendation form Refer to page 7 for camshaft recommendation form
All 00060 cid

Springs Part No. Lifters 84322 66915-16 68340-16
Retainers Seals Remarks 87062-16 86072-16 Solid. 7500 plus rpm.
For severe duty applications, Crower recommends using our solid lifter with the added "coolface oiling option". Specify X980 after corresponding component kit. Spring pressure: 68340-16 Seat: 1.900" @ 119 lbs / Nose: 1.350" @ 359 lbs / Coil bind: 1.080" ACCESSORIES (Machine work, use cutter 68986). Part No. Description Optional spring (race only): See pg. 180 Spring seat cutter 68385X2-16 Seat: 1.900" @ 166 lbs / Nose: 1.300" @ 422 lbs / Coil bind: 1.100" Pg's. 146-149 Pushrods (Machine work, use cutter 68979). See pg. 139 Alum/Bronze distributor gear Note: Screw-in rocker studs should be used when installing solid lifter camshafts to insure See pg. 138 Roller timing gear set (1972 - up) proper valve adjustment. Pg's.150-165 Rocker arms (1.73) 716 CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Note: If using guide plates, heat-treated pushrods (RC Valve timing events are available online at: www.crower.com/valvtime.html 60 series) are required. See pushrods or contact Crower.
Note: If exceeding 7500 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower.
96
ROLLER CAMSHAFTS
Mechanical 1968-1994 370 429 460 V8
Note: These cams use .026" intake, .028" exhaust valve lash. Description (Note: See pages 8-9 for a detailed explanation of each Performance Level)
Ford
.572" 84527 .645" 84527 .648" 84527 84524S .668" 84527 84524S .698" 84527 84524S .721" 84528 84524S .754" 84528 84524S See Below
Advertised Duration Gross Lift Rec Grind C.I.D. Part Duration @ .050" 1.73 / 1.73 Group Number Lobe Center Intake Exhaust Intake Exhaust Intake Exhaust Kit
STREET ROLLER / PERFORMANCE LEVEL 4 - Excellent street/strip profile. 429 22401 RPM Power Range: 2500 to 6000 / Redline: 7500 plus. 460 ULTRA-ACTION / PERFORMANCE LEVEL 5 -High torque oval track profile. 429 22402 RPM Power Range: 3750 to 7000 / Redline: 7500 plus. 460 ULTRA-ACTION / PERFORMANCE LEVEL 5 - Strong mid-range design. RPM Power Range: 4000 to 7250 / Redline: 7750 plus. ULTRA-ACTION / PERFORMANCE LEVEL 5 - Fast 3/8 to 1/2 mile super oval track profile. RPM Power Range: 4250 to 7500 / Redline: 8000 plus. 429 22403 460 429 22404 460
286R 110 290R 108 300R 108 308R 108 316R 108 322R 110 330R 110
275 290 300 308 316 322 330
284 234 296 249 310 258 314 264 322 272 328 282 338 284
244 .570" 254 .642" 268 .654" 268 .666" 277 .690" 280 .757" 288 .769"
ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag 429 22405 profile. RPM Power Range: 4500 to 7750 / Redline: 8250 plus. 460 ULTRA-ACTION / PERFORMANCE LEVEL 5 - Mid-range and top end drag 429 22406 profile. RPM Power Range: 4750 to 8000 / Redline: 8500 plus. 460 ULTRA-ACTION / PERFORMANCE LEVEL 5 - Full top end power profile. RPM Power Range: 5000 to 8250 / Redline: 8750 plus. CUSTOM GROUND ROLLER - Special order roller lifter camshaft ground to your specifications. Call our technical support staff for personalized camshaft assistance.
8620 Steel Billet Cam Cores.
429 22407 460 All 00002 cid

Springs Retainers Seals Keepers Remarks Part No. Lifters 84527 66217-16 68363-16 87064-16 86072-16 86110-16 8000 plus rpm. Race only. 84523 66217-16 68804-16 87063M-16 84524S 66217-16 68385X2-16 86071-16 86072-16 Steel retainer, for daily street use. Spring pressure: 68363-16 Seat: 1.900" @ 212 lbs / Nose: 1.200" @ 560 lbs / Coil bind: 1.100" (Machine work, use cutter 68992*). Optional springs: 68804-16 Seat: 1.900" @ 257 lbs / Nose: " @ lbs / Coil bind: " (Machine work, use cutter). * Machine work required, specify 1132 pilot shaft when ordering. Note: Screw-in rocker studs should be used when installing roller lifter cams to insure proper valve adjustment. Note: Roller cams and kits available for Boss 429. Contact Crower for technical assistance. CAUTION! When using high lift cams pay close attention to retainer, oil seal and valve guide clearance at full lift (minimum .050"). Valve timing events are available online at: www.crower.com/valvtime.html HIPPO Note: For severe duty roller lifter applications, we highly recommend using our roller lifters with Hippo High Pressure Pin Oiling. Specify H in the part number. Ex. 66290X874H-16
ACCESSORIES
Part No. See pg. 180 Pg's. 146-149 See pg. 139 See pg. 138 Pg's.150-165
Description Spring seat cutter Pushrods Alum/Bronze distributor gear Roller timing gear set (1972 - up) Rocker arms (1.73) 716
Note: If using guide plates, heat-treated pushrods (RC 60 series) are required. See pushrods or contact Crower. Note: If exceeding 8000 rpm, high pressure springs and titanium retainers may be required. See specs or contact Crower.
97

Ford - Rec Kit

Uploaded by

Copyright:

Available Formats

Ford - Rec Kit

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ford - Rec Kit

Uploaded by

Copyright:

Available Formats

4.6L/5.

4L SOHC MODULAR (2 Valve) - Low Lift Design

X-TREME MILEAGE CAMS AVAIL ABLE!

Refer to page 7 for camshaft recommendation form

ENGINEERED COMPONENT KITS

NEW HIGH RPM VALVE SPRING

1999-up (Late Model Cylinder Head)

4.6L/5.4L SOHC MODULAR (2 Valve) - High Lift Design

FACTORY OEM SPECS (1999-up)

.295" .504" .531" Stock .303" .529" .545" Stock

.305" .540" .549" Stock

.322" .581" .581"

.334" .590" .601"

.340" .612" .612"

.345" .612" .621"

Refer to page 7 for camshaft recommendation form

ENGINEERED COMPONENT KITS

4.6L/5.4L SOHC MODULAR (3 Valve)

X-TREME MILEAGE CAMS AVAIL ABLE!

Refer to page 7 for camshaft recommendation form

ENGINEERED COMPONENT KITS

4.6L/5.4L DOHC MODULAR (4 Valve)

X-TREME MILEAGE CAMS AVAIL ABLE!

Refer to page 7 for camshaft recommendation form

ENGINEERED COMPONENT KITS

FOCUS ZX3 - Twin Cam (1998-up)

Lobe Lift Intake Exhaust

.346" .341" Stock .352" .352" Stock

.374" .374" Stock

.413" .393" 84169

.393" .393" 84169

.433" .413" 84169

.454" .433" 84169

ENGINEERED COMPONENT KITS

2.0 & 2.3L DURATEC - Twin Cam

.358" .317" .363" .328"

Refer to page 7 for camshaft recommendation form

ENGINEERED COMPONENT KIT

2000cc 4 Cylinder (3 Bearing)

292 240 250

296 264 276

231 202 216

242 .448" 216 .445" 226 .469"

288 302 308

302 308 312

254 264 272

268 .528" 268 .563" 280 .570"

.561" .573" .571"

Refer to page 7 for camshaft recommendation form

Diagram 1. Follower Geometry (Sample based on intake of 25307)

.321" x 1.6 = .514"

Correct Contact surface

For rpm up to 7000 max.

.321" x 1.52 = .488"

Wrong Valve or Lash Cap too short

.321" x 1.7 = .546"

Wrong Valve or Lash Cap too long

2300cc 1974-up 2000cc 1982-up (4 Bearing)

All cid All cid All cid

280 222 286 228