0% found this document useful (0 votes)
521 views8 pages

CU-XE R2 Technical Data

Uploaded by

Edward Uy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
521 views8 pages

CU-XE R2 Technical Data

Uploaded by

Edward Uy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Communication

Industrial and commercial

CU-XE Release 2

E65C
Technical data

E65C-XE communication units provide Ethernet communication


between E650, S650 or E850 meters and the metering and SCADA systems.

Date: 14.03.2020
File name: D000062527 E65C CU-XE Technical Data en b.docx

© Landis+Gyr D000062527 en b
2/8

Revision history
Version Date Comments
a 10.07.2018 First edition
b 14.03.2020 Adaptations for Release 2:
– Passthrough can be configured in combination with other devices
– Simultaneous use of protocols (Modbus server, SCADA IEC 60870-5-104 server,
Modbus client, DLMS/COSEM client)
– Ethernet ports fully configurable
– Maximum transmission speed of serial ports 115.2 kbps
– Time synchronisation based on base meter time or NTP
– OpenVPN
– Manufacturer access can be allowed with DIP switch setting
– Temperature sensor
– Several minor layout changes

Although the information contained within this document are presented in good faith and believed to be correct, Landis+Gyr (including its affiliates,
agents and employees) disclaim any and all liability for any errors, inaccuracies or incompleteness relating to the product. Landis+Gyr makes no
warranty, representation or guarantee regarding the performance, quality, durability or suitability of the products for any particular purpose. To the
fullest extent permitted by law Landis+Gyr disclaims (1) any and all liability arising out of the use of the product, (2) any and all liability, including, but
without limitation to, special, consequential and indirect damages and losses, and (3) any and all implied warranties, including, but without limitation
to, fitness for purpose and merchantability.
The information contained in this document is strictly confidential and is intended for the addressee only. The unauthorised use, disclosure, copying,
alteration or distribution of this document or the contents thereof is strictly prohibited and may be unlawful.
All product information are subject to change without notice.

© Landis+Gyr D000062527 en b – E65C CU-XE Release 2 – Technical data


3/8

E65C CU-XE Release 2 – Technical data


Design Ethernet interfaces RJ45 socket
Product type options 1 TxD+
Type 10/100BASE-TX RS485/RS422 RS232 2 TxD-
3 RxD+
CU-XE    4 not used
5 not used
Virtual bus (configurable) 6 RxD-
Interfaces base meter, Ethernet, 7 not used
8 not used
RS485/RS422, RS232 orange speed
green link
8 1
Supported service protocols
DLMS/IEC 62056-21 passthrough (base meter: data
readout) RS485/RS422 interface RJ45 socket
Passthrough and bridging protocol independent,
1 not used
verification recommended 2 GND
Passthrough can also be configured in combination with 3 Tx+
other devices, e.g. E65C CU-L52 fitted into an ADPx 4 Tx-
5 Rx-
6 Rx+
Simultaneous use of protocols 7 GND
1. Modbus server 8 not used
2. SCADA IEC 60870-5-104 server (directly to SCADA orange speed
system) green link
8 1
3. Modbus client over both TCP/IP and serial connec-
tion (for additional Modbus devices)
4. DLMS/COSEM client for base meter and additional RS232 interface RJ45 socket
devices 1 DSR
2 DCD
Installation 3 DTR
4 GND
Directly in meter (E650 ZxD300/400xT, E850 ZxQ or
5 RxD
S650 SxD400xT) 6 TxD
External operation with E65C CU adapter ADPx 7 CTS
8 RTS
Processor and hardware description orange speed
green link
Application processor ARM Cortex-A5 8 1
Clock speed 600 MHz
Core performance 828 DMIPS
Connection to meter or CU adapter
DRAM capacity 256 Mbyte
10-pin connector at rear of CU
FLASH capacity 8 Gbyte
Encryption co-processor AES, 3DES
Ethernet connections
Connections All Ethernet ports 10/100-BASE-TX
Terminal layout Standard IEEE 802.3
Duplex half or full
Auto MDI/MDIX
Reinforced insulation SELV voltage
Max. cable length up to 100m
Ethernet ports fully configurable

Network bridging
Number of devices in bridging mode tested up to 20

#1: Ethernet port 1 #3: RS485/RS422


#2: Ethernet port 0 #4: RS232

D000062527 en b – E65C CU-XE Release 2 – Technical data © Landis+Gyr


4/8

Serial connections Networking-related functions


RS485/RS422 port RJ45 TCP/IP stack
Application asymmetric, serial, asynchronous, IPv4 stack
half-duplex (RS485) or full-duplex (RS422), OpenVPN
bi-directional for multi-drop bus
DLMS/IEC application configuration Network bridge
Maximum number of slaves 31
Master/slave configurable Indicators
Max. cable length and speed environment/cable
dependent LED display (top to bottom)
Typical use cases Boot/Ready, Connect, Error, Running
- Up to 550 m at 115.2 kbps with 31 slaves Ethernet states green: no link, link, activity
orange: 10 Mbps, 100 Mbps
- Up to 1000 m at 115.2 kbps with 15 slaves
Built-in terminations
120 Ohm line termination selectable with DIP switch Configuration switches
and 680 Ohm bias network DIP switch
Reinforced insulation SELV voltage Position 1 ON = rx termination enabled, 120 Ω
Position 2 ON = tx termination enabled, 120 Ω
RS232 port RJ45 Position 3 ON = rx bias enabled
Application asymmetric, serial, asynchronous, Position 4 ON = rx bias enabled
full-duplex, bi-directional Position 5 ON = Manufacturer access
Standard EIA RS232-F / ITU-T V.24 Position 6 ON = used as RS485 (half-duplex)
Pin-out EIA-561 OFF = used as RS422 (full-duplex)
Maximum transmission speed 115.2 kbps Position 7 ON = used as RS485 (half-duplex)
Maximum cable length 3m OFF = used as RS422 (full-duplex)
Reinforced insulation SELV voltage Position 8 ON = used as RS485 (half-duplex)
OFF = used as RS422 (full-duplex)
Information storage security
Encrypted storage of configuration files, user data and Power consumption
the applications in FLASH memory. Maximum active/apparent power
4.0 W
Firmware security
Cryptographic verification of all firmware executed by Environmental influences
the processor from secure boot start-up.
In general same as for base meter
Exception operating temperature -40 to +55°C
Device management
Pollution Degree 2
OpenAPI (RESTful) for system integration
Web UI for device configuration
Temperature sensor
Access control Provides actual temperature in communication unit for
Role-based access using passwords for configuration monitoring of internal temperature
management or firmware updates using HTTPS (TLS). Range +25 to +85°C
Resolution 0.01°C
Management-related functions Accuracy 1°C
Update time approx. every second
Time synchronisation options
Time synchronisation based on base meter time or NTP
Insulation strength to meter
Firmware updates Insulation strength 4 kV at 50 Hz for 1 min.
Secure HTTPS-based firmware update and configuration Insulation spacing at least 6.3 mm
management.
Firmware signed with digital signature. Conformance
Insulation test according EN 61010-1:2010
Event logging Protective class II, double insulation
Syslog RFC 5424 logging of device boot, network link AC voltage isolation 4 kVrms 50 Hz/1min.
activity, application activity, security changes, network 6 kV peak 1.2/50 us
activity, login attempts and firmware updates. Logs are
stored in non-volatile memory.

© Landis+Gyr D000062527 en b – E65C CU-XE Release 2 – Technical data


5/8

EMC emissions tests according to IEC 61000-6-3 Weight and dimensions


Radio noise voltage to lines IEC-CISPR 11: 150 kHz to 30
Weight
MHz limit Class B
approx. 100 g
Radio noise to air IEC-CISPR 11: 30 MHz to 1000 MHz
limit Class B
Width / height / depth
65 / 107 / 38 mm
EMC immunity tests according to IEC 61000-6-2
Note: Longer than standard CU
ESD 8 kV contact discharge, 15 kV air discharge
RF EM field, amplitude modulation IEC 61000-4-3: 10
V/m; 80 MHz to 2.5 GHz; 80 % AM; 1 kHz Material
HF on lines, AM IEC 61000-4-6: 10 V RS485/RS422 150 Case
kHz to 80 MHz; 80 % AAM, 1 kHz polycarbonate
HF on lines, AM EN 55024: 3 V RS232; 150 kHz to 80
MHz; 80 % AAM, 1 kHz

Functional block diagram

CU-XE

Ethernet interface
Protocol
Protocol
Slave
Master
SPI interface (event
(timer driven) Datahub
2-channel driven)
multiplexer Management
to base Ethernet interface
meter Interface
DLMS/IEC passthrough (virtual bus) selector

Serial interface
RS232 (DTE)
TCP/UDP/ICMP/IP/ Operating system
bridging networks with drivers

Linux OS Serial interface


RS485/RS422

Power supply LEDs DIP switches

D000062527 en b – E65C – CU-XE Release 2 – Technical data © Landis+Gyr


6/8

Typical application diagram

IT infrastructure
AMR SCADA NTP server, domain controller, RADIUS
control centre server, remote access server, etc.

Modem
bank
Firewall Control centre level

Untrusted communication
Telephone Internet/packet network
network network

PSTN/CSD 2G/3G/4G IP router with


modem Modem firewall Station level

Ethernet Station Local


switch controller HMI

E650/ RS232 E10/100


E850/
S650
SPI CU-XE
RS485/RS422
Process level

Single protocol only,


multi-drop bus

Fault
i.e. Modbus CU-Bx IED
detector

Fault detector or
meter, but not
S650/
both at the same
E850
time

© Landis+Gyr D000062527 en b – E65C CU-XE Release 2 – Technical data


7/8

Type designation

CU-X E .

Product
CU Communication unit

Product type
X Advanced architecture

Primary interface type


E Ethernet

D000062527 en b – E65C – CU-XE Release 2 – Technical data © Landis+Gyr


Contact:
Landis+Gyr AG
Theilerstrasse 1
CH-6301 Zug
Switzerland
Phone: +41 41 935 6000
www.landisgyr.com

You might also like