mtx3 en Om h0

Owner’s Manual
EN
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
CAUT I ON within an equilateral triangle is intended to
alert the user to the presence of uninsulated
RISK OF ELECTRIC SHOCK “dangerous voltage” within the product’s
DO NOT OPEN
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to per-
sons.
CAUTION: TO REDUCE THE RISK OF The exclamation point within an equilateral
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE triangle is intended to alert the user to the
PARTS INSIDE. REFER SERVICING TO presence of important operating and mainte-
QUALIFIED SERVICE PERSONNEL. nance (servicing) instructions in the literature
accompanying the product.
The above warning is located on the top of the unit.
IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions. 11 Only use attachments/accessories specified by the
2 Keep these instructions. manufacturer.
3 Heed all warnings. 12 Use only with the cart, stand,
4 Follow all instructions. tripod, bracket, or table speci-
5 Do not use this apparatus near water. fied by the manufacturer, or
6 Clean only with dry cloth. sold with the apparatus. When
7 Do not block any ventilation openings. Install in a cart is used, use caution
accordance with the manufacturer’s instructions. when moving the cart/appara-
8 Do not install near any heat sources such as radia- tus combination to avoid injury
tors, heat registers, stoves, or other apparatus from tip-over.
(including amplifiers) that produce heat. 13 Unplug this apparatus during lightning storms or
9 Do not defeat the safety purpose of the polarized or when unused for long periods of time.
grounding-type plug. A polarized plug has two blades 14 Refer all servicing to qualified service personnel. Ser-
with one wider than the other. A grounding type plug vicing is required when the apparatus has been dam-
has two blades and a third grounding prong. The aged in any way, such as power-supply cord or plug
wide blade or the third prong are provided for your is damaged, liquid has been spilled or objects have
safety. If the provided plug does not fit into your out- fallen into the apparatus, the apparatus has been
let, consult an electrician for replacement of the exposed to rain or moisture, does not operate nor-
obsolete outlet. mally, or has been dropped.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the appara-
tus.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
(UL60065_03)
2 MTX3 Owner’s Manual

FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! all installations. If this product is found to be the source of
This product, when installed as indicated in the instructions interference, which can be determined by turning the unit
contained in this manual, meets FCC requirements. Modifi- “OFF” and “ON”, please try to eliminate the problem by using
cations not expressly approved by Yamaha may void your one of the following measures:
authority, granted by the FCC, to use the product. Relocate either this product or the device that is being
2. IMPORTANT: When connecting this product to accessories affected by the interference.
and/or another product use only high quality shielded cables. Utilize power outlets that are on different branch (circuit
Cable/s supplied with this product MUST be used. Follow all breaker or fuse) circuits or install AC line filter/s.
installation instructions. Failure to follow instructions could In the case of radio or TV interference, relocate/reorient the
void your FCC authorization to use this product in the USA. antenna. If the antenna lead-in is 300 ohm ribbon lead,
3. NOTE: This product has been tested and found to comply change the lead-in to co-axial type cable.
with the requirements listed in FCC Regulations, Part 15 for If these corrective measures do not produce satisfactory
Class “B” digital devices. Compliance with these require- results, please contact the local retailer authorized to distrib-
ments provides a reasonable level of assurance that your ute this type of product. If you can not locate the appropriate
use of this product in a residential environment will not result retailer, please contact Yamaha Corporation of America,
in harmful interference with other electronic devices. This Electronic Service Division, 6600 Orangethorpe Ave, Buena
equipment generates/uses radio frequencies and, if not Park, CA90620
installed and used according to the instructions found in the
The above statements apply ONLY to those products distrib-
users manual, may cause interference harmful to the opera-
uted by Yamaha Corporation of America or its subsidiaries.
tion of other electronic devices. Compliance with FCC regu-
lations does not guarantee that interference will not occur in
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
IMPORTANT NOTICE FOR THE UNITED KINGDOM COMPLIANCE INFORMATION STATEMENT

Connecting the Plug and Cord (DECLARATION OF CONFORMITY PROCEDURE)
WARNING: THIS APPARATUS MUST BE EARTHED IMPOR-
Responsible Party : Yamaha Corporation of America
TANT. The wires in this mains lead are coloured in accordance Address : 6600 Orangethorpe Ave., Buena Park,
with the following code: Calif. 90620
GREEN-AND-YELLOW : EARTH Telephone : 714-522-9011
BLUE : NEUTRAL Type of Equipment : Matrix Processor
BROWN : LIVE Model Name : MTX3
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the This device complies with Part 15 of the FCC Rules.
terminals in your plug proceed as follows: Operation is subject to the following two conditions:
The wire which is coloured GREEN-and-YELLOW must be 1) this device may not cause harmful interference, and
connected to the terminal in the plug which is marked by the 2) this device must accept any interference received including
letter E or by the safety earth symbol or colored GREEN or interference that may cause undesired operation.
GREEN-and-YELLOW. See user manual instructions if interference to radio reception
is suspected.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK. * This applies only to products distributed by (FCC DoC)
The wire which is coloured BROWN must be connected to the YAMAHA CORPORATION OF AMERICA.
terminal which is marked with the letter L or coloured RED.
(3 wires)
ADVARSEL! NEDERLAND / THE NETHERLANDS

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. • Dit apparaat bevat een lithium batterij voor geheugen back-up.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren. • This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de bat-
VARNING terij op het moment dat u het apparaat ann het einde van de
Explosionsfara vid felaktigt batteribyte. Använd samma batteri- levensduur of gelieve dan contact op te nemen met de verte-
typ eller en ekvivalent typ som rekommenderas av apparattill- genwoordiging van Yamaha in uw land.
verkaren. Kassera använt batteri enligt fabrikantens • For the removal of the battery at the moment of the disposal
instruktion. at the end of life please consult your retailer or Yamaha rep-
resentative office in your country.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda • Gooi de batterij niet weg, maar lever hem in als KCA.
paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. • Do not throw away the battery. Instead, hand it in as small
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. chemical waste.
(lithium caution) (lithium disposal)
This product contains a battery that contains perchlorate material. 이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서
Perchlorate Material—special handling may apply, 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습
See www.dtsc.ca.gov/hazardouswaste/perchlorate. 니다.
* This applies only to products distributed (Perchlorate) (class b korea)

by YAMAHA CORPORATION OF AMERICA.
MTX3 Owner’s Manual 3

PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited
to, the following:
Power supply/Power cord Water warning

• Do not place the power cord near heat sources such as heaters or radiators, and do not • Do not expose the device to rain, use it near water or in damp or wet conditions, or
excessively bend or otherwise damage the cord, place heavy objects on it, or place it in place on it any containers (such as vases, bottles or glasses) containing liquids which
a position where anyone could walk on, trip over, or roll anything over it. might spill into any openings. If any liquid such as water seeps into the device, turn off
• Only use the voltage specified as correct for the device. The required voltage is printed the power immediately and unplug the power cord from the AC outlet. Then have the
on the name plate of the device. device inspected by qualified Yamaha service personnel.
• Use only the supplied power cord/plug. • Never insert or remove an electric plug with wet hands.
If you intend to use the device in an area other than in the one you purchased, the
included power cord may not be compatible. Please check with your Yamaha dealer. Fire warning
• Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it. • Do not put burning items, such as candles, on the unit. A burning item may fall over
and cause a fire.
• Be sure to connect to an appropriate outlet with a protective grounding connection.
Improper grounding can result in electrical shock.
If you notice any abnormality
Do not open • When one of the following problems occur, immediately turn off the power switch and
disconnect the electric plug from the outlet. Then have the device inspected by Yamaha
• This device contains no user-serviceable parts. Do not open the device or attempt to
service personnel.
disassemble the internal parts or modify them in any way. If it should appear to be
- The power cord or plug becomes frayed or damaged.
malfunctioning, discontinue use immediately and have it inspected by qualified - It emits unusual smells or smoke.
Yamaha service personnel. - Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the device.
• If this device should be dropped or damaged, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by qualified
Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or
damage to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord Maintenance

• When removing the electric plug from the device or an outlet, always hold the plug • Remove the power plug from the AC outlet when cleaning the device.
itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the device is not to be used for extended Handling caution
periods of time, or during electrical storms.
• Do not insert your fingers or hands in any gaps or openings on the device (vents).
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or
Location openings on the device (vents). If this happens, turn off the power immediately and
• Do not place the device in an unstable position where it might accidentally fall over. unplug the power cord from the AC outlet. Then have the device inspected by qualified
• Do not block the vents. This device has ventilation holes at the front and sides to Yamaha service personnel.
prevent the internal temperature from becoming too high. In particular, do not place the • Do not rest your weight on the device or place heavy objects on it, and avoid use
device on its side or upside down. Inadequate ventilation can result in overheating, excessive force on the buttons, switches or connectors.
possibly causing damage to the device(s), or even fire. • Do not use the device/speakers for a long period of time at a high or uncomfortable
• Do not place the device in a location where it may come into contact with corrosive volume level, since this can cause permanent hearing loss. If you experience any
gases or salt air. Doing so may result in malfunction. hearing loss or ringing in the ears, consult a physician.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is easily Backup battery
accessible. If some trouble or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even when the power switch is turned • This device has a built-in backup battery. When you unplug the power cord from the AC
off, electricity is still flowing to the product at the minimum level. When you are not outlet, the internal data is retained. However, if the backup battery fully discharges, this
using the product for a long time, make sure to unplug the power cord from the wall AC data will be lost. When the backup battery is running low, the [PRESET] display
outlet. indicates “12.” In this case, immediately save the data to external device such as a
computer, then have qualified Yamaha service personnel replace the backup battery.
• If the device is mounted in an EIA standard rack, carefully read the section “Precautions
for rackmounting” on page 7. Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), malfunction, or even fire. Yamaha cannot be held responsible for damage caused by improper use or
• Keep device away from the reach of children. modifications to the device, or data that is lost or destroyed.
Connections Always turn the power off when the device is not in use.
• Before connecting the device to other devices, turn off the power for all devices. Before
turning the power on or off for all devices, set all volume levels to minimum.
4 MTX3 Owner’s Manual PA_en_1 1/1

NOTICE Information
To avoid the possibility of malfunction/ damage to the product,  About this manual
damage to data, or damage to other property, follow the notices • The illustrations as shown in this manual are for instructional
below. purposes only, and may appear somewhat different from
those on your device.
 Handling and Maintenance • Ethernet is a trademark of Xerox Corporation.
• Do not use the device in the vicinity of a TV, radio, stereo • Windows is a registered trademark of Microsoft ® Corpora-
equipment, mobile phone, or other electric devices. Other- tion in the United States and other countries.
wise, the device, TV, or radio may generate noise. • SDHC Logo and SD Logo are trademarks of SD-3C, LLC.
• Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day), in order to prevent the
possibility of panel disfiguration, unstable operation, or dam-
age to the internal components. • The company names and product names in this manual are
• Do not place vinyl, plastic or rubber objects on the device, the trademarks or registered trademarks of their respective
since this might discolor the panel. companies.
• When cleaning the device, use a dry and soft cloth. Do not • MPEG Layer-3 audio coding technology licensed from
use paint thinners, solvents, cleaning fluids, or chemical- Fraunhofer IIS and Thomson.
impregnated wiping cloths.
• Condensation can occur in the device due to rapid, drastic
changes in ambient temperature—when the device is moved
from one location to another, or air conditioning is turned on
or off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that
condensation might have occurred, leave the device for sev-
eral hours without turning on the power until the condensa-
tion has completely dried out.
• When turning on the AC power in your audio system, always
turn on the power amplifier LAST, to avoid speaker damage.
When turning the power off, the power amplifier should be
turned off FIRST for the same reason.
 Saving data
This device has a built-in backup battery that maintains data in
internal memory even when the device’s power is switched off.
The backup battery will eventually become depleted, however,
and when that happens the contents of the internal memory will
be lost.* To prevent loss of data be sure to replace the backup
battery before it becomes fully depleted. If the backup battery
runs low, alert number “12.” will appear in the [PRESET] display
either while the unit is starting up. If this occurs, do not turn off the
power, but immediately save the data to a computer or other
external storage device, and then have qualified Yamaha service
personnel replace the backup battery. The average life of the
internal backup battery is approximately five years, depending on
operating conditions.
* Data items maintained in the internal memory by the backup

battery are as follows:
• Contents of the current preset and the preset number
• Parameters specific to the unit (e.g., configuration data)
• Current parameters for peripheral devices within the same
system
• Event log
Data items other than those described above are stored in
memory that does not require backup power, and will be
retained even if the backup battery fails.
Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic
products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accor-
dance with your national legislation.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your waste
disposal service or the point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities
or dealer and ask for the correct method of disposal.
(weee_eu_en_02)

Contents
PRECAUTIONS................................................................................................................4
Getting Started................................................................................................................7
Included items (please check) ................................................................................................ 7
Firmware versions................................................................................................................... 7
Precautions for rackmounting.................................................................................................. 7
Introducing the MTX3.....................................................................................................8

Features.................................................................................................................................. 8
About MTX-MRX Editor .......................................................................................................... 8
Using the PDF manual............................................................................................................ 8
Controls and Connectors ..............................................................................................9

Front Panel.............................................................................................................................. 9
Rear Panel ............................................................................................................................ 10
Euroblock plug connection............................................................................................. 12
Quick Guide ..................................................................................................................14

Preparations.......................................................................................................................... 14
On-site work (Installation and wiring) .................................................................................... 15
On-site work (Settings in MTX-MRX Editor).......................................................................... 16
Various Procedures ......................................................................................................17

Recalling (switching) presets ................................................................................................ 17
Switching presets from the MTX3 .................................................................................. 17
Setting the clock.................................................................................................................... 17
Using the scheduler .............................................................................................................. 17
Connecting via the [GPI] connector ...................................................................................... 18
Using the MTX3 to play audio files saved on an SD memory card ....................................... 19
Inserting an SD memory card........................................................................................ 19
Removing the SD memory card..................................................................................... 19
Initializing the MTX3 ............................................................................................................. 19
Appendix .......................................................................................................................21
Troubleshooting..................................................................................................................... 21
Alert list ................................................................................................................................. 22
Specifications........................................................................................................................ 23
Input/Output Characteristics ................................................................................................. 24
Dimensions ........................................................................................................................... 24
Block Diagram....................................................................................................................... 25
Index ..................................................................................................................................... 26

Getting Started
Thank you for purchasing the Yamaha Matrix Processor MTX3. This manual will help you take full
advantage of the superior functionality offered by the MTX3. After you have read the manual, keep it
in a safe place for reference when needed.
Included items (please check) Firmware versions

• MTX3 Owner’s Manual (this document) Use MTX-MRX Editor to update the firmware of the MTX3 or
• Power cable check the firmware version. For details on operation, refer to the
• Euroblock plug (16-pin, 3.50mm pitch) (1) MTX-MRX Editor User Guide.
Download the latest firmware from the “Downloads” page on
• Euroblock plugs (3-pin, with tab, 5.08mm pitch) (16)
the following website.
• Cable ties (16)
http://download.yamaha.com/
Precautions for rackmounting

This device is guaranteed to operate at an ambient temperature
of 0 to 40 °C. If this device is mounted in an EIA rack together
with other devices, heat from the various devices may cause the
temperature inside the rack to rise, rendering this device unable
to perform to its full potential. To ensure that heat does not
accumulate inside this device, please ensure that the following
conditions are met when rack-mounting it.
• If you plan to mount this device together with devices that
tend to generate heat, such as power amps other than XMV
series products, allow 1U or more of vacant space between
this device and other devices. Also attach ventilation panels
in this space or leave them open to ensure sufficient ventila-
tion.
• Leave the back of the rack open, and allow at least 10 cm of
space between the rack and the wall or ceiling to ensure suf-
ficient ventilation. If the back of the rack cannot be left open,
provide forced air cooling for the rack, for example by
installing a commercially available fan kit. If you install a
fan kit, leaving the back of the rack closed may provide more
effective cooling. For details, refer to the owner’s manual
provided with the rack or fan kit.

Introducing the MTX3
Features About MTX-MRX Editor

• A signal processor suitable for small or mid-sized MTX-MRX Editor is software for the Windows operating sys-
installed systems tem that allows unified construction and control of systems that
The MTX3 is a signal processor suitable for small or mid- use the MTX series.
sized systems such as retail establishments or banquet halls. In
MTX-MRX Editor and the MTX-MRX Editor User Guide can
addition to a 26 ch. x 8 ch. matrix mixer, it provides 3-band
be downloaded from the following website.
parametric EQ, compressor/gate, auto gain control, eight pri-
ority duckers, and four feedback suppressors. For the output http://download.yamaha.com/
stages, it provides numerous high-performance high-quality
processors, such as 4-band parametric EQ, delay, and speaker For details on installing MTX-MRX Editor and connecting the
processor. MTX3 to your computer, refer to the “MTX Setup Manual.”
• Newly-developed “YDIF” digital audio transmis-

sion format
“YDIF” is a digital audio transmission format that uses Ether-
net cable to send and receive up to 16 channels of audio and Using the PDF manual
word clock. You can use Ethernet cables up to 30 meters long
to easily make connections between devices. The MTX-MRX Editor User Guide is an electronic file in PDF
format. You can read this book on a computer. Use Adobe®
• Versatile input/output and SD memory card slot
Reader® to read this book on screen, search for words very
In addition to eight high-quality monaural mic/line inputs and
quickly, print specific pages, or click links to display sections of
two stereo line inputs, digital input/output via “YDIF” can
special interest. The ability to search for words, or to follow
allow up to 16 channels of input. An SD memory card slot for
links directly to relevant sections in the document, are helpful
playback is also provided; allowing MP3/WAV audio files
attributes of this electronic file format. We encourage you to
saved on the SD memory card to be played back. In addition to
take advantage of these benefits.
eight channels of analog monaural output, a maximum of 16
You can download the latest Adobe Reader application from the
channels of digital audio can be output via a “YDIF” connec-
website listed below.
tion.
http://www.adobe.com/
• Support for external controls
By connecting a “DCP” series dedicated wall-mounted control
panel to the [DCP] connector, you can easily control the vol-
ume of multiple zones or switch presets. Daisy-chain connec-
tion via Ethernet cable allows up to eight “DCP” series control
panels to be connected. The total cable length from the MTX3
to the farthest control panel can be up to 200 meters, and
power is also supplied, allowing you to place the control panel
in the ideal location for the room. A NETWORK connector
and [GPI] connector are also provided for controlling the unit
from an AMX/Crestron or other touch panel device.
• Two built-in effect processors
Two effect processors are built-in, and can be easily used in a
party room or banquet hall. You can easily obtain effects such
as reverb or karaoke echo without needing to add dedicated
effect processors.
• Dedicated “MTX-MRX Editor” application soft-
ware for designing the entire system
“MTX-MRX Editor” is application software for editing the
parameters of the MTX3. Using operating screens that reflect
the workflow of designing the installation, this software
makes it easy to design a system and make (or adjust) settings.
A speaker library of Yamaha-manufactured speakers is also
built-in, making it easy to choose settings that will maximize
the performance of your speakers.
• iPhone app support
A dedicated iPhone app makes it easy to control the volume
and manage presets in the same way as when using the dedi-
cated wall-mounted control panel. You can use your iPhone/
iPod touch to easily control the sound system of a retail loca-
tion or a banquet hall.

Controls and Connectors
Front Panel
q we t yu i o !0 !4
88
r !1 !2 !3
q SD memory card slot !0 [NETWORK] indicator

You can insert an SD memory card here. Music or sound This indicator will light green if a link is established with an
effects can be played back from an SD memory card contain- external device via the rear panel NETWORK connector
ing audio files (MP3 files and WAV files). Before you insert (page 10). It will flash while data is being sent or received.
an SD memory card into the slot, or remove an SD memory
card from the slot, remove the slot cover. !1 [YDIF] indicator
For details on SD memory card handling, refer to page 19. This indicator will light green if the rear panel [YDIF IN]
For details on how to play back audio files, refer to the connector (page 11) is correctly connected to the [YDIF
MTX-MRX Editor User Guide. OUT] connector of another device.
w [INPUT PEAK] indicators 1–8 !2 [SCHEDULER] indicator

These indicators will light red when the input level of the This indicator will light yellow if an even has been specified
corresponding INPUT channel is -3 dBFS or higher. in the scheduler (page 17), and will start flashing one minute
before the event.
e [INPUT SIGNAL] indicators 1–8
These indicators will light green when the input level of the !3 [SD/ACT] indicator
corresponding INPUT channel is -40 dBFS or higher. This indicator will light yellow if an SD memory card is
inserted in the SD memory card slot (q) and has been
r [OUTPUT SIGNAL] indicators 1–8 detected correctly. It will flash while the SD memory card is
These indicators will light green when the output level of the being accessed.
corresponding OUTPUT channel is -40 dBFS or higher.
!4 Power switch
t [PRESET] display This is the power switch. The power is on if the switch is in
This display usually shows the preset number. It can also the position. The power is off if the switch is in the
show the UNIT ID, alert number, or a message. position.
NOTE
y [s]/[t] buttons
• Do not cycle the power switch in rapid succession. Wait at
Use these buttons to change the preset number or alert num- least 6 seconds before turning the power switch on after it
ber shown in the above [PRESET] display. has been turned off. Failing to observe this precaution
may cause malfunctions.
u [ENTER] button • Even when the power switch is turned off, a small amount
Use this button to confirm the item shown in the above of current is flowing through the unit. If you plan not to use
[PRESET] display. the unit for a long period of time, remove the power cable
from the AC outlet.
When an alert number is shown, pressing this button will
return to the preset number display.
i [ALERT] indicator
When an alert occurs, the [PRESET] display will indicate
the alert number and this indicator will flash red.
o [POWER] indicator
This indicator will light when this device is powered-on.

Rear Panel
q e u i !0 !1
!2 w r t y o
NOTE Up to eight control panels can be connected to one MTX3.

The MTX3 has some connectors that are shaped identically but The total length of the cables from the MTX3 to the last con-
have a completely different function (e.g., [DCP] connector, NET- trol panel must not exceed 200 meters.
WORK connector, [YDIF] connector). Make the appropriate con-
nections as instructed by the explanation for each connector. CAUTION
Otherwise, you risk damaging your equipment. • Do not connect a control panel to any connector
other than the MTX3’s [DCP] connector. Since the
control panel is not electrically compatible, such con-
q AC IN connector nections may cause fire or malfunction.
Use the included power cord to supply power to this connec- • Never connect any device to the [DCP] connector
tor. First, connect the power cord to this device, and then other than the separately sold DCP or other control
insert the power cord plug into the AC outlet. panel. Doing so may damage the other device or this
device.
w Ground screw
The supplied power cord has a three-prong plug that will y NETWORK connector
ground the device when plugged into an appropriately This is an Ethernet connector that supports AutoMDI/MDI-
grounded three-prong type AC mains outlet. In some cases, X. It can either be connected directly to a computer, or via a
you may be able to reduce hum or interference by also con- network switch to communicate with a computer, peripheral
necting this screw to ground. device, or external controller. Use a CAT5e or better Ether-
net STP cable (shielded twisted pair cable).
e [GPI] connector
This Euroblock connector allows input and output of control u [UNIT ID] rotary switch
signals via GPI (General Purpose Interface). When multiple devices are connected within the same net-
The MTX3 provides seven ports of analog/digital input, one work, this switch specifies the ID by which MTX3 devices
port of digital input, and four ports of output. The [IN]-1–7 are individually distinguished.
terminals detect voltage changes from 0V to 5V. The [IN]-8 DIP switches 1 and 2 described below specify the upper
terminal alone supports +24V input; voltages in the range of digit, and this rotary switch specifies the lower digit,
2.5–24V are detected as High, and voltages below 2.5V are together allowing you to set the UNIT ID to one of 63 possi-
detected as Low. The [OUT]-1–4 terminals are open collec- bilities in the range of 01 to 3F.
tor outputs; they will change between open or closed
NOTE
(Ground). The +5VDC terminals has an output voltage of
• Do not use a UNIT ID of “00” (DIP switches 1 and 2 OFF
5V. Use the included Euroblock plugs to make connections and the rotary switch at 0).
(see “Euroblock plug connection” on page 12 for details). • You’ll need to restart the device after changing the setting
For details on connections and usage, refer to “Connecting of the [UNIT ID] rotary switch.
via the [GPI] connector” on page 18.
CAUTION i DIP switches

Do not input a voltage higher than 5V to the [IN]-1–7 These switches enable you to specify the settings related to
pins. Doing so may damage your equipment. the startup operation of the unit.
NOTE
r [RS-232C] connector
Set the DIP switches while the power to the unit is turned
This 9-pin D-SUB connector allows connection to an RS- OFF. Otherwise, the setting will not be effective.
232C compatible controller such as those from AMX or Cre-
stron. Refer to the following for details.
Switch Status
t [DCP] connector
Use this connector to daisy-chain separately sold control Represent a status with switch toggled up.
panels such as the DCP1V4S to control the MTX3. Use a Represent a status with switch toggled
CAT5e or better Ethernet straight cable that has all eight pins down.
connected.

 Switches 1–2 (UNIT ID)  Switches 7–8 (START UP MODE)

These switches specify the upper digit and the above- These specify whether the MTX3 will be initialized when
mentioned [UNIT ID] rotary switch specifies the lower it is powered-on.
digit, together allowing you to specify one of 63 different Switch position Option Functions
UNIT ID numbers in a range from 01 to 3F.
This is the normal operating
Switch position Option Functions mode. When you power-on
The [UNIT ID] rotary switch the MTX3, it will start up in
UNIT ID is RESUME
will have a setting range of the same state in which it
“0x” was when the power was
01 through 0F.
turned off.
The [UNIT ID] rotary switch
UNIT ID is Initializes the MTX3, return-
will have a setting range of INIT.
“1x” ing it to the factory-set state
10 through 1F. (INITIALIZE)
(page 19).
The [UNIT ID] rotary switch
UNIT ID is
will have a setting range of
“2x”
20 through 2F. o [YDIF] connectors
The [UNIT ID] rotary switch These connectors are used to make a ring connection with
UNIT ID is
will have a setting range of the devices that comprise the MTX/MRX system, allowing
“3x”
30 through 3F. digital audio signals to be transmitted and received. Use
NOTE CAT5e or better Ethernet STP cables (shielded twisted pair
Do not use a UNIT ID of “00” (DIP switches 1 and 2 OFF cables) that have all eight pins connected in a straight con-
and the rotary switch at 0). nection. The maximum cable length between devices is 30
meters, and you can connect up to eight devices that are
 Switches 3–4 equipped with the [YDIF] connectors. For details, refer to
Not used. Turn it off (up) at any time. the MTX-MRX Editor User Guide.
 Switch 5 (PANEL LOCK)
!0 [ST IN] connectors
This switch locks the front panel controls. Use this if you
These are unbalanced RCA phono jacks for inputting analog
want to prevent accidental operation from the front panel.
audio signals from a CD player or other device.
Switch position Option Functions
UNLOCK
The front panel controls will !1 [INPUT]/[OUTPUT] connectors
be available for operation. These are balanced input/output connectors for analog audio
The front panel controls will input and output. Connect line level devices or microphones
be locked, and will be inop-
to the [INPUT] connectors, and line level devices to the
LOCK erable. The device can be
operated from a computer [OUTPUT] connectors. The [INPUT] connectors provide
or an external controller. head amps, and can also provide +48V phantom power.
MTX-MRX Editor is used to specify the gain of the internal
 Switch 6 (IP SETTING) head amps and to turn the phantom power on/off.
This switch specifies how the MTX3’s IP address will be Use the included Euroblock plugs to make connections (see
specified. “Euroblock plug connection” on page 12 for details).
Switch position Option Functions NOTE

The IP address will be Adjusting the internal head amp gain between +17 dB and
specified according to the +18 dB will internally turn PAD on/off. Noise may occur if
UNIT ID there is an impedance difference between the Hot and Cold
UNIT ID, and will be
192.168.0.(UNIT ID). of a device connected to the [INPUT] connectors while
phantom power is being used.
The IP address will be
determined by the settings
PC of MTX-MRX Editor. (See !2 Cooling vent
“MTX-MRX Editor User The MTX3 contains a cooling fan. The cooling air is
Guide.”) exhausted here, so please be careful not to block this vent.
NOTE
You must set this to the “UNIT ID” position the first time
you connect this device to a computer after purchase. If
you subsequently want to specify the IP address instead
of using the UNIT ID, specify the IP address from MTX-
MRX Editor and then switch this setting to the “PC” posi-
tion.
Cooling vent

 Euroblock plug connection 1. Loosen the terminal screws.

Use the included Euroblock plugs when making connections
to the [INPUT]/[OUTPUT] connectors and [GPI] connector. Loosen
Slotted screwdriver
Cable preparation
approx. 7 mm Terminal screw
(approx. 5 mm for
the GPI connector)
Euroblock plug
approx. 20 mm Tab
• Use stranded wire for Euroblock connections, and * The explanation uses tabbed Eurob-
strip the wire as shown in the illustration. With a lock plugs.
Euroblock connection, the stranded wire may be
prone to breakage because of metal fatigue due to NOTE
the weight of the cable or due to vibration. Cables Use a slotted screwdriver with a blade width of 2 mm or
connected to the [INPUT]/[OUTPUT] connectors less for the [GPI] connector’s Euroblock plug (16-pin),
should be fastened to the tab of the Euroblock plug and a blade width of 3 mm or less for the [INPUT]/[OUT-
(3-pin) using the included cable ties (see illustration PUT] connector’s Euroblock plug (3-pin).
at right). When rack-mounting the device, use a lac-
3 mm or less
ing bar when possible to bundle and secure the
cable.
NOTE
Do not tin (plate with solder) the stranded wire. 2. Insert cables.
+ –
• If cables will be frequently connected and discon- G
nected, as in the case of a portable system, we rec-
ommend that you use ferrules with insulation
sleeves. Use a ferrule whose conductor portion has
an external diameter of 1.6 mm or less (1.3 mm or
less for the [GPI] connector) and a length of approx-
imately 7 mm (approximately 5 mm for the [GPI]
connector) such as the AI 0,5 - 6 WH made by the
Phoenix Contact corporation.
3. Securely tighten the terminal screws.
approx. 7 mm Pull the cables (not too strongly) to confirm that they are
(approx. 5 mm for securely connected.
the GPI connector)
4. For the Euroblock plugs (3-pin) of the
[INPUT]/[OUTPUT] connectors, use the
1.6 mm or less included cable ties to fasten the cable to the
(1.3 mm for the GPI connector) tab.
NOTE
Trim off the extra portion of the cable tie as necessary.

5. Plug the Euroblock plug into the [GPI] con-

nector or [INPUT]/[OUTPUT] connector of
the MTX3.
NOTE
When connecting unbalanced cables to the [INPUT]
connector, use a jumper wire to connect the “-” and “G”
of the Euroblock.
+ –
G

Quick Guide
This section explains basic settings and connection procedures for constructing an MTX/MRX system
using the MTX3. Some of the steps may not be necessary for your system; if so, proceed to the next step.
7. The audio signal flow in the MTX3 and the

Preparations principal parameters to be set are as follows.
Use MTX-MRX Editor to make the required settings before you Make the settings in the order shown.
actually install and connect the equipment. For details on each item, refer to “MTX-MRX Editor User
Guide.”
1. Prepare a computer in which to install MTX-
MRX Editor. Input port settings (e.g., HA gain, +48V on/off)
2. Install MTX-MRX Editor in your computer.

Input patching
For details on installation, refer to “MTX Setup Manual.”
3. Specify the IP address and subnet mask of Input channel settings (e.g., gain, HPF, EQ)
your computer.
Enter “192.168.0.253” as the IP address and
“255.255.255.0” as the subnet mask. Matrix
4. If you want to play back music or other audio

Matrix/zone settings
files from the MTX3 itself, prepare an SD mem-
ory card.
Copy the audio files to your SD memory card. For details on Router
SD memory card handling, refer to “Using the MTX3 to play
audio files saved on an SD memory card” (page 19).
Output channel settings (e.g., output level, delay/
room EQ, speaker processor)
5. Start up MTX-MRX Editor.
For details on installing and using MTX-MRX Editor, refer
to “MTX Setup Manual” and “MTX-MRX Editor User Output patching
Guide.”
Output port settings (e.g., polarity, output gain)

6. Set up the entire MTX/MRX system as directed
by the wizard.
Make settings such as the number of connected MTX/XMV/ Make settings for the necessary components while offline.
Exi8/EXo8/DCP devices, and the UNIT ID and YDIF mode
• HA section:
(Cascade mode or Distribution mode) for each device. For
HA gain, +48V (phantom power)
details on YDIF, refer to “Features” (page 8), and “o
[YDIF] connectors” in “Controls and Connectors” (page 11). • Input channel section:
Print out the schematic diagram shown at the end of the wiz- HPF, 3BAND EQ, GATE, COMP, FBS, AGC, Level
ard, and use it when you make the actual connections and • Matrix/Zone section:
settings. Two-level priority ducker, ANC
• Output channel section:
Room EQ (Delay, 4Band EQ), SPEAKER PROCES-
SOR (X-over, Delay, 6Band EQ, Level, Limiter)

Quick Guide
8. Make DCP settings.

Assign the parameters of the MTX3 to the switches and On-site work (Installation and wiring)
knobs of the connected DCP units. Here you can also spec-
Install and connect the system while referring to the schematic
ify the brightness of the DCP’s LEDs. For details on how to
diagram you printed out.
make DCP settings, refer to “MTX-MRX Editor User
Guide.”
1. Install the MTX3, and make the analog audio
connections.
9. As necessary, make settings for devices
other than the MTX3.
2. Make digital connections between the MTX3
For details, refer to “MTX Setup Manual.”
and any XMV/EXi8/EXo8.
10. Specify and store a preset. Make a ring connection with the devices equipped with a
[YDIF] connector.
You can use presets to change the volume of zones and the
audio source to play (e.g., SD memory card or CD player)
in a single action. To prevent problems such as a sudden
3. Connect the MTX3 to an analog input amp.
increase in volume when the MTX3 is operated, we recom-
mend that you store the preset with the output level lowered 4. Set the UNIT ID of the MTX3 and the XMV/
to “-infinity ().” For details on presets and how to recall EXi8/EXo8.
them, refer to “Recalling (switching) presets” on page 17, Set the UNIT ID for every MTX3 and XMV/EXi8/EXo8
and “MTX-MRX Editor User Guide.” device you connected in the above steps. The UNIT ID is
specified by the combination of the [UNIT ID] rotary switch
11. Save your settings and close MTX-MRX Edi- and DIP switches located on each device’s rear panel. Set
tor. each device to a different UNIT ID so that no conflict occurs.
A project file with the extension “.mtx” will be created.
5. Make connections between the MTX3 and the
DCP units.
Daisy-chain the DCP units. Set the panel ID and termination
settings of the DCP units. For details, refer to the DCP
owner’s manual.

Quick Guide
On-site work (Settings in MTX-MRX

Editor)
Use MTX-MRX Editor to make adjustments for the entire sys-
tem.
1. Connect the computer to the MTX3/XMV/

EXi8/EXo8 via a network switch.
If you’re using only the MTX3, you can connect it directly
to the computer.
2. Start up MTX-MRX Editor and load the proj-

ect file that you previously created.
3. Power-on the MTX3.
4. Power-on the XMV/EXi8/EXo8 and the analog

input amps.
5. In the [To Device] direction, place the MTX3/

XMV/EXi8/EXo8 and MTX-MRX Editor online
(in a synchronized state).
“Online” refers to the state in which the MTX3/XMV/
EXi8/EXo8 itself is connected with MTX-MRX Editor and
is synchronized. When the devices are online, MTX-MRX
Editor can be used to control the MTX3/XMV/EXi8/EXo8.
For details on how to put the device online, refer to “MTX-
MRX Editor User Guide.”
6. Check the presets.

Recall a preset, and verify that the settings are correct.
For details on presets and how to recall them, refer to
“Recalling (switching) presets” on page 17.
7. Check the signal processing.

Input audio signals into the MTX3, and check the meters in
MTX-MRX Editor to verify that the volume and routing are
set correctly.
8. Adjust the output level of the MTX3 and the

output level of the amps so that the audio is
output from the speakers at an appropriate
level.
One by one, turn on each output channel and adjust its out-
put level.
9. Store the preset.

Recall, edit, and save other presets in the same way.
10. Save your settings and close MTX-MRX Edi-

tor.
A project file with the extension “.mtx” will be created.
NOTE
The settings you make while online are saved in the MTX3
itself, but we recommend that you use MTX-MRX Editor to
save them as a project file for future maintenance and
readjustments.

Various Procedures
Recalling (switching) presets Using the scheduler

With the MTX/MRX system, input/output port patching, matrix The scheduler can switch presets or play music and sound
mixer settings, and the parameters of XMV amps within the effects from the SD memory card at the date and time you spec-
same MTX/MRX system are stored together as a “preset” in the ify. Each such setting is called an “event.”
MTX3 and in MTX-MRX Editor for recall when desired. Event settings are made in the “Scheduler” dialog box of MTX-
Each MTX/MRX system can store 50 presets. MTX-MRX Edi- MRX Editor. For details on operation, refer to “MTX-MRX
tor is used to edit presets. Editor User Guide.”
Each preset contains settings such as the following. < Example 1 >
• Input/output port settings and patching Switching background music and playback area
• Input/output channel gain and EQ settings according to the time of day
• Matrix mixer settings In commercial facilities that switch background music and play-
• Zone settings back areas at different times of the day, you can switch the type
• Routing settings of music and the playback area according to the time of day.
• Effect settings
• DCA and mute group settings 9:00 12:00 14:00 18:00 22:00
• Parameter settings for XMV devices within the same MTX/
MRX system
Indoors
• Preset name Energetic Atmospheric
music music
For details, refer to “MTX-MRX Editor User Guide.” Refreshing Calm music
music
Outdoors No music No music
 Switching presets from the MTX3

1. While watching the [PRESET] display, use
< Example 2 >
the [s]/[t] buttons to select the preset
Switching the playback time according to the day
number that you want to recall.
of the week
The [PRESET] display will flash during this time.
In commercial facilities that switch the time period of music
depending on the day of the week, you can specify the music
2. Press the [ENTER] button to confirm your
pattern and playback times according to the day of the week and
selection.
the hours of operation.
The [PRESET] display will stop flashing; the preset has
been recalled. • Monday–Friday
NOTE 10:00 20:00
• If you leave the device for 30 seconds with the [PRE- Music pattern 1
SET] display flashing, it will revert to the previous pre-
set number. • Saturday
• If a control panel such as a DCP series unit is con-
10:00 22:00
nected, you’ll be able to easily switch presets.
Music pattern 2
• Sunday
Setting the clock 12:00 20:00
Music pattern 3
Each time the devices connected to the MTX/MRX system are
brought online, the date and time of the computer will be trans-
You can also play seasonal music, or specify exceptions such as
mitted to all devices, automatically updating their internal
stopping playback on days when the facility is not operating.
clocks.
You can also update the date and time settings on all devices
connected to the same network by transmitting the computer’s
date and time settings from the “Clock” dialog box in MTX-
MRX Editor.
For more information on operation, refer to “MTX-MRX Editor
User Guide.”

Various Procedures
• Connection examples using the [GPI IN] con-

Connecting via the [GPI] connector nector
GPI (General Purpose Interface) devices can be connected to Example: Controlling the MTX3 from a switch box
the rear-panel [GPI] connectors. GPI allows a variety of control MTX3
signals to be exchanged with external controllers or other
devices.
+5VDC
+V
IN
CPU A/D
100k
The MTX3 provides 8 input ports and 4 output ports.

Example: Controlling the MTX3 with a 10k ohm
• The +5VDC terminals have an output voltage of 5V. The linear taper potentiometer.
maximum current draw is 100 mA total for the two termi-
MTX3
nals. If you are using a switch/variable resistor and an LED/
relay simultaneously, connect one terminal to the switch/ +5VDC
variable resistor and the other terminal to the LED/relay. +V
• The [IN]-1–7 terminals detect voltage changes from 0V to
5V. The [IN]-8 terminal alone supports +24V input; volt- IN Variable
CPU A/D
ages in the range of 2.5–24V are detected as High, and volt- resistor
GND
ages below 2.5V are detected as Low. 100k
• The [OUT]-1–4 terminals are open collector outputs; they
will change between open or closed (Ground). The maxi-
mum voltage that can be applied is +12V. The maximum
current draw is 75 mA per port.
• Connection examples using the [GPI OUT]
The GPI controller parameters are assigned via the MTX-MRX connector
Editor application.
Example: Lighting LED indicators on external
Euroblock plugs (16-pin) are used for connections to the [GPI] devices from the MTX3
connector. For details, refer to “Euroblock plug connection” on
MTX3
page 12.
NOTE +5VDC
By making input/output channel settings in MTX-MRX Editor,
+V
you can recall presets or edit parameters on an external GPI
device or send signals to it. For details, refer to the “MTX-MRX 10 OUT
Editor User Guide.”
CPU Max. 75mA
CAUTION
Do not exceed 75 mA of current from the OUT con-
nector.
Example: Lighting an LED by switching an exter-
nal device’s relay from the MTX3
MTX3
+5VDC +
+V
10 OUT
CPU
–
Max. 75mA
NOTE
For the method of adjusting the detection range of the input
voltage at the [GPI] connector (calibration), refer to the “MTX-

Various Procedures
Using the MTX3 to play audio files Initializing the MTX3

saved on an SD memory card Here’s how to initialize the MTX3’s internal memory, restoring
it to the factory settings.
The MTX3 can use commercially available SD memory cards
to play back audio files such as music and sound effects without
needing to connect a CD player or other audio device. The 1. Power-off the MTX3.
MTX3 can play back audio files in either MP3 or WAV formats. 2. Set the rear panel DIP switches 7 and 8 to the
“INIT. (INITIALIZE)” position.
Here we explain how to handle SD memory cards. In order to
play back audio files saved on an SD memory card, you must
make settings in MTX-MRX Editor. For details, refer to “MTX-
NOTE 3. Power-on the MTX3.

Use an SD format or SDHC format memory card (SDXC format
Initialization will start.
is not supported). However, depending on the manufacturer or
type of memory card, some memory cards might not work cor- The status of execution is shown by the front panel [ALERT]
rectly with the MTX3. indicator and the various indicators from [NETWORK]
through [SD/ACT].
• During initialization:
 Inserting an SD memory card All indicators from [NETWORK] through [SD/ACT]
1. Use a 2.5 mm hex key to open the cover of will flash.
the SD memory card slot.
2. With the terminals of the SD memory card
facing downward, insert the card straight
into the slot until it clicks into place.
• Initialization completed:
Only the [NETWORK] indicator and the [YDIF] indi-
cator will flash.
When the SD memory card has been correctly recog-

nized, the [SD/ACT] indicator (page 9) will light. The
[SD/ACT] indicator will flash while the card is being
accessed.
NOTE • Initialization failed:

To prevent theft of the SD memory card, we recommend The [ALERT] indicator will flash.
that you leave the cover installed during use.
 Removing the SD memory card

1. Gently press the SD memory card inward.
The card will pop out slightly; gently pull it completely
out.
CAUTION
Do not turn off the power to the MTX3 during initializa-
tion. Otherwise, a malfunction may occur.
NOTE
If initialization failed, contact Yamaha representatives /
authorized distributors to have the device inspected. A list of
Yamaha representatives / authorized distributors appears
near the end of this manual.

Various Procedures
4. When initialization is completed, power-off the

MTX3 once again.
5. Set the rear panel DIP switches 7 and 8 to the
“RESUME” position.
6. Power-on the MTX3 again.

The MTX3 will start up in its factory-set state.

Appendix
 Troubleshooting
The Yamaha Pro Audio website provides a FAQ (a list of frequently asked questions, with answers).
http://www.yamahaproaudio.com/
Symptom Possible cause, and action

Connect the power cord properly.
The device does not turn on, or
Make sure that the power switch is turned on.
the panel LEDs do not light up.
If the power still does not turn on, contact your Yamaha dealer.
Is the NETWORK connector on the MTX3 properly connected to your computer?
Can’t exchange data between the
Have you specified the correct UNIT ID using the [UNIT ID] rotary switch and DIP switches 1 and 2
MTX3 and MTX-MRX Editor
on the rear panel? Could the UNIT ID be conflicting with another device?
(MTX3 is not shown in MTX-MRX
Editor). Set the rear panel DIP switch 6 (IP SETTING) to “UNIT ID” so that the IP address will be automati-
cally assigned according to the UNIT ID.
Connect the cable properly.
No audio input is present.
([INPUT SIGNAL] indicator does Make sure that a signal from an external device is being input.
not light)
Set the gain of the internal head amplifier or external head amplifier to an appropriate level.
Could the output level be lowered?
No audio is output. In MTX-MRX Editor, could the channel’s ON button be turned off?
([OUTPUT SIGNAL] indicator
does not light) Is the signal routing specified correctly?
Have the other settings in MTX-MRX Editor been made correctly?
Could rear panel DIP switch 5 (PANEL LOCK) be set to “LOCK”? Change this to “UNLOCK” to
The panel controls don’t work. defeat the panel lock function. If you are still unable to operate the device, contact your Yamaha
dealer.
Are you using an appropriate cable, and is the MTX3 correctly connected to the DCP?
Did you power-cycle the MTX3 after connecting the DCP? The DCP will be detected when the
power is turned on.
Did you assign the DCP’s ID and parameters correctly in MTX-MRX Editor? Also, did you specify a
Can’t operate the DCP. DCP library item in the “Preset” dialog box as the preset to be recalled?
Is termination turned on for the last-connected DCP?
Could nine or more DCP units be connected? A maximum of eight DCP units can be connected to
one MTX3.
Could the total cable length from the MTX3 to the last control panel be exceeding 200 meters?
The DCP’s LEDs are dim. Did you set the DCP’s LED brightness appropriately in MTX-MRX Editor?
Did you use an appropriate cable to make proper YDIF connections between the MTX3 and other
[YDIF] indicator does not light.
devices in the MTX/MRX system? Also, is the power to the YDIF-connected devices turned on?
Is the SD memory card recognized correctly? Make sure that the front panel [SD/ACT] indicator is lit
or flashing.
Can’t play audio files from the SD
In MTX-MRX Editor, have you made the correct settings for SD memory card playback and for the
memory card.
scheduler?
Are playable audio files saved in the specified folder?
Are you using an SD memory card type and format that is supported? Refer to the “Specifications”
page, and use a supported card.
SD memory card is not detected. Is the SD memory card inserted correctly? Turn off the power of the MTX3, re-insert the card, and
then turn the power on again. If the [SD/ACT] indicator does not light and the card is not detected, it
may be that the card is damaged.
The MTX3’s clock is set by sending clock data from the computer via MTX-MRX Editor to the MTX3.
Preset does not switch at the time Make sure that the computer’s clock is set correctly.
specified by the scheduler. Have you made the correct scheduler settings in MTX-MRX Editor? If the [SCHEDULER] indicator
is not lit or flashing, it may be that settings were not made correctly in MTX-MRX Editor.
An error has occurred. The alert number is shown in the front panel [PRESET] display; refer to
The [ALERT] indicator is flashing.
“Alert list” on page 22 to determine the content of the error and take the appropriate action.
Can’t switch presets from a device Is the GPI device connected correctly?
connected to the [GPI] connector. Have the correct GPI-related settings been made in MTX-MRX Editor?
Volume becomes unstable when
Route the wiring to avoid picking up noise; for example, replace the cable with a shielded or shorter
it is operated from a device con-
cable.
nected to the [GPI] connector.

Appendix
 Alert list
This is a list of the alerts that may be indicated in the front panel [PRESET] display.
Alert
Meaning Response
number
Turn the power off, then turn on after waiting at least 6 seconds. If this does not
01–09 The device has not started up correctly. solve the problem, please initialize the memory (use rear panel DIP switches 7
and 8). Should this also fails, contact your Yamaha dealer.
The internal backup battery has been When you turn off the power, the current settings will be lost, and will return to the
10
completely exhausted or is not installed. default values. Please stop use immediately, and contact your Yamaha dealer.
The internal backup battery has run
When you turn off the power, the current settings will be lost, and will return to the
11 extremely low, and it is possible that the
default values. Please stop use immediately, and contact your Yamaha dealer.
internal memory has been cleared.
This does not affect the operation of the device. However, if you continue using the
The internal backup battery has only a
12 device, the settings may be lost and reset to the default values. Contact your
small amount of power remaining.
Yamaha dealer as soon as possible.
If this occurs each time you turn on the power, it is possible that the internal
A problem has occurred with the internal backup battery has run down or that the device has malfunctioned. Contact your
13 clock, and it has been initialized (January Yamaha dealer.
1, 2000, 0:00). If this occurs only once, an abnormality was detected with the clock setting and it
was initialized; use MTX-MRX Editor to set the time.
The current preset saved in internal mem-
14 Recall the preset. If this does not solve the problem, contact your Yamaha dealer.
ory has been lost.
The settings saved in internal memory Either the internal backup battery has run low, or the device has malfunctioned.
15
have been lost. Contact your Yamaha dealer.
The word clock master has become
21 Make sure that the word clock signal is being input correctly.
unlocked.
The digital signal being input to the [YDIF
22 IN] connector is not synchronized to the
word clock of this device.
The digital signal being input to the [YDIF Make sure that YDIF cables are properly connected.
23 IN] connector is not continuously synchro- Use cables that meet the required specifications.
nized to the word clock of this device.
There is a problem with the connection of
30
the [YDIF IN] connector.
40 Duplicate IP addresses. Change the IP addresses so that there are no duplicates.
IP address was not set within 60 seconds Please check rear panel DIP switch 6 (IP Setting). If DIP switch 6 is set to “PC,”
41
of startup. use MTX-MRX Editor or DHCP server to specify the device IP address.
A device within the MTX/MRX system Power-on all devices in the system, and make sure that they are correctly con-
42
was not found on the network. nected to the network.
Too many devices are connected to the
43 Reduce the number of devices connected to the network.
network.
50 The UNIT ID is set to “00.” Set the UNIT ID to something other than “00.”
Devices with identical UNIT IDs were
51 found connected within the same net- Change the UNIT ID so that there are no duplicates.
work.
• If an error was shown in the DCP panel, refer to the DCP owner’s manual and
A communication error occurred with the take the appropriate action.
52
[DCP] connection. • Ensure that the panel ID of the DCP units do not conflict.
• Verify that the cables are correctly connected and are within the specified length.
The DCP connected to the [DCP] connec-
• Check that the required DCP is connected.
53 tor has been configured differently from
• Check whether a different model of DCP might be connected.
the project settings.
56 SD memory card was not recognized. Use an SD memory card that complies with the specifications. (See page 23.)
Unable to play the specified file or folder Verify that the specified audio file or folder exists in the SD memory card. There
58
in the SD player. must be at least one playable audio file in the specified folder.
Initialize the memory of the device (use rear panel DIP switches 7 and 8). If this
60 A preset recall attempt has failed.
does not solve the problem, contact your Yamaha dealer.
The recall could not be executed because
Specify a preset that exists. No sound will be output unless an appropriate preset
61 the preset to be recalled when the MTX
is recalled.
starts up was not found.
• The Preset selected for recall cannot be recalled as no data has been stored to it.
• Another device may have been added after presets were stored. Please synchro-
64 The preset could not be recalled.
nize and check all presets using MTX-MRX Editor, edit as necessary and store
again.
Synchronization has not been com- Perform synchronization again using MTX-MRX Editor. If this does not solve the
70 pleted. It may be that synchronization was problem, initialize the memory of the device and synchronize again. If this also
halted before completion. fails, contact your Yamaha dealer.
The UNIT ID settings when synchroniza-
Do not change any UNIT ID’s after performing synchronization. If you’ve changed
71 tion was performed do not match the cur-
any UNIT ID’s, perform synchronization again.
rent UNIT ID settings.

Appendix
 Specifications
Product specifications
Dimensions (W x H x D) 480(W) x 44(H) x 351(D)mm, 1U
Weight 4.8 kg
Japan: 100V 50/60Hz
Power supply voltage US/Canada: 110V–240V 50/60Hz
Others: 100V–240V 50/60Hz
Power consumption 50W max.
Heat dissipation (per hour) 43kcal max.
Operating temperature range 0 °C–40 °C
Storage temperature range -20 °C–60 °C
NC value 27 (1m from the front panel)
Number of memories Preset memories: 50
Maximum number of simulta- Four MTX devices (However in a system in which one to four MTX devices are connected, a total of up
neously usable devices to 20 devices including devices such as the XMV can be connected.)
Power cord length 2.5m
Power cord, Euroblock plugs (3-pin, tabbed) x 16, Euroblock plug (16-pin) x 1, cable ties x 16,
Included items
owner’s manual
Separately sold options DCP1V4S-US/EU, DCP4V4S-US/EU, DCP4S-US/EU digital control panels
Electrical specifications
Sampling frequency 48kHz/44.1kHz
Signal delay Less than 2.5ms (AD-DA @48kHz)
Frequency response 20Hz to 20kHz, -1.5dB min, 0dB typ., +0.5dB max.
Total harmonic distortion Less than 0.05% (+4dBu, Gain:-6dB); less than 0.1% (+4dBu, Gain:+66dB)
Dynamic range 107dB (Gain:-6dB)
Equivalent input noise (EIN) -126dBu (Gain: +66dB)
Crosstalk / Channel separation -100dB (@1kHz)
[YDIF] connector: 30 meters (Cable length between devices)
Maximum cable length
[DCP] connector: 200 meters (total cable length from the MTX3 to the last DCP)
INPUT PEAK: RED -3dBFS
Indicators INPUT SIGNAL: GREEN -40dBFS
OUTPUT SIGNAL: GREEN -40dBFS
Phantom power 48V (per channel; individually settable)
Connector specifications
[GPI] connector: IN (1-7ch): 0–5V
IN (8ch): 2.5–24V : High, 2.5V or less: Low, Allowable input +24V
OUT: Open collector
Format
+V: DC5V
NETWORK connector: 100Base-TX
[RS-232C] connector: RS-232C (BAUD RATE: 38.4 kbps/115.2kbps)
[DCP] connector: CAT5e or better Ethernet cable (Straight connected. All 8 pins must be connected.)
Cable specifications [YDIF] connector: CAT5e or better Ethernet STP cable (Straight connected. All 8 pins must be connected.)
NETWORK connector: CAT5e or better Ethernet STP cable
SD Memory card specifications

File formats: FAT32, FAT16, FAT12
Supported formats
Files created on a computer running Windows XP or later, or Mac OS X or later.
Maximum media capacity: SDHC: Max. 32 GB
Supported capacities
SD: Max. 2GB
FAT12: Max. 32MB
Maximum file size
FAT16: Max. 2GB
(maximum size per file)
FAT32: Max. 2GB
16bit 2ch PCM
Audio file format: WAV
Sampling frequencies: 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz
MPEG-1/2/2.5 Audio Layer-3
sampling frequencies: MPEG-1: 32kHz, 44.1kHz, 48kHz
MPEG-2: 16kHz, 22.05kHz, 24kHz
Audio file format: MP3
MPEG-2.5: 8kHz, 11.025kHz
Bit rate: MPEG-1: 32kbps–320kbps, VBR (Variable Bit Rate) * However, free format is excepted.
MPEG-2, 2.5: 8 kbps–160 kbps, VBR (Variable Bit Rate) *However, free format is excepted.
* Specifications and appearance are subject to change without notice for improvement.
European Models
Inrush Current based on EN 55103-1: 2009
2A (on initial switch-on)
2A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Appendix
 Input/Output Characteristics
ANALOG INPUT CHARACTERISTICS
Input Actual Load For Use With Input Level
GAIN Connector
Terminals Impedance Nominal Nominal Max. before clip
+66dB 50–600Ω Mics -62dBu (0.616mV) -42dBu (6.16mV) Euroblock (Balanced)
INPUT 1–8 10kΩ
-6dB & 600Ω Lines +10dBu (2.45V) +30dBu (24.5V) (5.08mm pitch)
ST IN 1, 2 — 10kΩ 600Ω Lines -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack
• In these specifications, 0dBu = 0.775 Vrms., 0dBV = 1.00 Vrms.
• All input AD converters are 24bit linear, 128times oversampling.
• +48V DC (phantom power) is supplied to INPUT EUROBLOCK connectors via each individual software controlled switch.
ANALOG OUTPUT CHARACTERISTICS

Actual Source For Use With Output Level
Output Terminals Connector
Impedance Nominal Nominal Max. before clip
Euroblock (Balanced)
OUTPUT 1–8 75Ω 10kΩ Lines +4dBu (1.23 V) +24dBu (12.3V)
(5.08mm pitch)
• In these specifications, 0dBu = 0.775 Vrms.
• All output DA converters are 24bit, 128times oversampling.
 Dimensions
430
351
356
362
4
6
480
44
Unit: mm

INPUT OUTPUT
INPUT PORT PATCH INPUT CHANNEL MATRIX ZONE ROUTER OUTPUT CHANNEL PATCH OUTPUT PORT
YDIF MODE
CASCADE MODE
or DISTRIBUTION MODE
PILOT TONE
YDIF MODE MATRIX FX ANC LEVEL ON
CASCADE MODE 1 2 7 8 1 2 1 2 Sine Wave To YDIF OUT
or DISTRIBUTION MODE 20.0kHz
CASCADE I/O YDIF OUT
CASCADE ON *CASCADE MODE only
YDIF IN 1
CASCADE ON YDIF OUT 1 8 8
*DISTRIBUTIO N MODE only
YDIF IN *CASCADE MODE only YDIF IN 2 CASCADE ON OSCILLATOR YDIF OUT
CASCADE ON YDIF OUT 2 YDIF YDIF
8 8 FREQ. Sine Wave From INPUT CHANNEL POST ON 1-8
YDIF IN 8 CASCADE ON LEVEL ON 8 OUTPUT 16
INPUT INPUT Pink Noise SUM OUT
CASCADE ON YDIF OUT 8 PATCH
METER From STEREO INPUT CHANNEL POST ON 1L-3R
YDIF IN PATCH From PILOT TONE
Burst Noise
 Block Diagram
YDIF *DISTRIBUTIO N MODE only *CASCADE MODE only 6 16

YDIF IN
From ZONE OUT 1-8
IN 16 1-16
8
To PRIORITY/AMBIENT SOURCE ZONE 1-8 ROUTER From THRU 1-16
To ROUTER IN
To YDIF OUTPUT PATCH 16
MATRIX OUT 2nd PRIORITY 1st PRIORITY ANC ZONE OUT
INPUT CHANNEL(CH1-8) LEVEL METER GR GR MASTER METER
8
LEVEL
D ON
EQ OUT POST ON MATRIX CRO SS PO INT PRIORITY PRIORITY
+48V ANC C
METER GR GR LEVEL METER To MATRIX(MO NO) DUCKER DUCKER
MIX MIX A 8
INPUT D ON LEVEL ON AMBIENT
+48V DIGITAL 3BAND To MATRIX1,3...7 METER To YDIF OUTPUT
METER HPF GATE COMP FBS* AGC* C A.Mixer*
GAIN EQ To MATRIX2,4...8 OUTPUT OUTPUT CHANNEL 1-8 (1way) OUTPUT
INPUT A PRIORITY PRIORITY AMBIENT PATCH OUTPUT PATCH
INPUT + * CH 1-4 only *CH 1-4 only OUTPUT POLARITY OUTPUT METER
- AD 1-8 To MATRIX(STEREO) SOURCE SOURCE SOURCE LEVEL ROOM EQ/DELAY SPEAKER PROCESSOR LEVEL GR METER GAIN
8 OUTPUT
1-8 LEVEL ON From INPUT CHANNEL POST ON 1-8 ON MUTE DA
GAIN PAN To MATRIX1,3...7 Fro m STEREO INPUT CHANNEL POST O N 1L-3R
4BAND 6BAND
INPUT DELAY X-OVER DELAY LIMITER 8
From DIRECT INPUT POST ON 9-16 EQ EQ 1-8
METER To MATRIX2,4...8 8 8
From ANC BUS 1-2
*1 From YDIF IN 1-16
AD
EFFECT SEND
ST IN INPUT ST IN LEVEL ON *1 DISTRIBUTION MODE only
SUM METER 1L-2R To FX1
OUTPUT CHANNEL 1-8 (2way)
To FX2 OUTPUT
1L-2R OUTPUT METER
AD To other MTXs LEVEL ROOM EQ/DELAY SPEAKER PROCESSOR LEVEL GR
ON MUTE
ANC SEND 4BAND 6BAND
DELAY DELAY LIMITER
LEVEL ON EQ EQ
To ANC1 OUTPUT
X-OVER GR METER
To ANC2 LEVEL
MUTE
SD IN SD IN 6BAND
DELAY LIMITER
SUM L-R To YDIF OUTPUT PATCH EQ
L-R To PRIORITY/AMBIENT SOURCE
STEREO INPUT CHANNEL(STIN1L-3R)

EQ OUT POST ON MATRIX CRO SS PO INT
METER GR LEVEL METER To MATRIX(MO NO)
D ON LEVEL ON
DIGITAL 3BAND To MATRIX1,3...7
COMP* AGC* C From YDIF IN 1-16
GAIN EQ To MATRIX2,4...8
A
*DISTRIBUTIO N MODE only 16
* CH 1L-2R o nly
To MATRIX(STEREO)
LEVEL ON To MATRIX1,3...7
PAN
To MATRIX2,4...8
EFFECT SEND
LEVEL ON
To FX1
To FX2
ANC SEND
LEVEL ON
To ANC1
To ANC2
To YDIF OUTPUT PATCH

To PRIORITY/AMBIENT SOURCE
DIRECT INPUT CHANNEL(CH9-16)

POST ON MATRIX CRO SS PO INT
LEVEL METER To MATRIX(MO NO)
D ON LEVEL ON
To MATRIX1,3...7
C
A To MATRIX2,4...8
To MATRIX(STEREO)
LEVEL ON To MATRIX1,3...7
PAN
To MATRIX2,4...8
EFFECT SEND
LEVEL ON
To FX1
To FX2
ANC SEND
LEVEL ON
To ANC1
To ANC2
EFFECT RETURN 1L-2R (FX RTN 1L-2R)

EFFECT POST ON MATRIX CRO SS PO INT
LEVEL METER To MATRIX(MO NO)
ON LEVEL ON
To MATRIX1,3...7
From FX1 EFFECT 1 To MATRIX2,4...8
EFFECT SEND
To MATRIX(STEREO) To EFFECT 1
LEVEL ON To MATRIX1,3...7 To EFFECT 2
PAN
To MATRIX2,4...8
From FX2 EFFECT 2 To PRIORITY/AMBIENT SOURCE
To oth er MTXs
MTX3 Owner’s Manual

25
Appendix
Appendix
 Index
Symbols L LOCK ......................................................................11
+48V .......................................................................11
[s/t] buttons ...........................................................9 M MTX-MRX Editor ......................................................8
[ALERT] indicator .....................................................9
N NETWORK connector ............................................10
[DCP] connector .....................................................10
[ENTER] button ........................................................9 O online ......................................................................16
[GPI] connector ......................................................10
[INPUT PEAK] indicator ...........................................9 P PANEL LOCK .........................................................11
[INPUT SIGNAL] indicator ........................................9 PC ..........................................................................11
[INPUT] connectors ................................................11 phantom power .......................................................11
[NETWORK] indicator ..............................................9 Power switch ............................................................9
[OUTPUT SIGNAL] indicator ....................................9 preset .......................................................8, 9, 15, 16
[OUTPUT] connectors ............................................11 project file .........................................................15, 16
[POWER] indicator ...................................................9
[PRESET] display .....................................................9
Q Quick Guide ............................................................14
[RS-232C] connector ..............................................10 R Rear Panel .............................................................10
[SCHEDULER] indicator ...........................................9 RESUME ................................................................11
[SD/ACT] indicator ....................................................9
[ST IN] connectors ..................................................11 S scheduler ................................................................17
[UNIT ID] rotary switch ...........................................10 schematic diagram .................................................14
[YDIF] connector ....................................................11 SD memory card ................................................9, 19
[YDIF] indicator .........................................................9 SD memory card slot ..........................................9, 19
START UP MODE ..................................................11
A AC IN connector .....................................................10 store .......................................................................15
Alert ....................................................................9, 22 subnet mask ...........................................................14
B Block Diagram ........................................................25 U UNIT ID ..............................................................9, 10

UNLOCK ................................................................11
C cable ties ............................................................7, 12
Cascade mode .......................................................14 W wizard .....................................................................14
control panel .............................................................8
Controls and Connectors ..........................................9 Y YDIF .........................................................................8
D DCP ..........................................................................8
DIP switch ..............................................................10
Distribution mode ...................................................14
E Euroblock plug ........................................7, 10, 11, 12

event .......................................................................17
F Features ...................................................................8
Front Panel ...............................................................9
G Ground screw .........................................................10
I INIT. (INITIALIZE) ..................................................11

Initializing ................................................................19
install ......................................................................14
IP address ..............................................................11
IP SETTING ...........................................................11

ADDRESS LIST
NORTH AMERICA NETHERLANDS/BELGIUM/ ASIA
LUXEMBOURG
CANADA Yamaha Music Europe Branch Benelux THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Canada Music Ltd. Clarissenhof 5b, 4133 AB Vianen, The Netherlands Yamaha Music & Electronics (China) Co.,Ltd.
135 Milner Avenue, Toronto, Ontario, Tel: +31-347-358040 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,
M1S 3R1, Canada Shanghai, China
Tel: +1-416-298-1311 FRANCE Tel: +86-400-051-7700
Yamaha Music Europe
U.S.A. 7 rue Ambroise Croizat, Zone d'activités de Pariest, INDIA
Yamaha Corporation of America 77183 Croissy-Beaubourg, France Yamaha Music India Private Limited
6600 Orangethorpe Avenue, Buena Park, CA 90620, Tel: +33-1-6461-4000 P-401, JMD Megapolis, Sector-48, Sohna Road,
U.S.A. Gurgaon-122018, Haryana, India
Tel: +1-714-522-9011 ITALY Tel: +91-124-485-3300
Yamaha Music Europe GmbH, Branch Italy
Via Tinelli N.67/69 20855 Gerno di Lesmo (MB), INDONESIA
CENTRAL & SOUTH AMERICA Italy PT. Yamaha Musik Indonesia (Distributor)
MEXICO Tel: +39-039-9065-1 Yamaha Music Center Bldg. Jalan Jend. Gatot
Yamaha de México, S.A. de C.V. Subroto Kav. 4, Jakarta 12930, Indonesia
SPAIN/PORTUGAL Tel: +62-21-520-2577
Av. Insurgentes Sur 1647 Piso 9, Col. San José Yamaha Music Europe GmbH Ibérica, Sucursal
Insurgentes, Delegación Benito Juárez, México, en España KOREA
D.F., C.P. 03900, México Ctra. de la Coruña km. 17,200, 28231 Yamaha Music Korea Ltd.
Tel: +52-55-5804-0600 Las Rozas de Madrid, Spain 8F, Dongsung Bldg. 21, Teheran-ro 87-gil,
BRAZIL Tel: +34-91-639-88-88 Gangnam-gu, Seoul, 06169, Korea
Yamaha Musical do Brasil Ltda. Tel: +82-2-3467-3300
GREECE
Rua Fidêncio Ramos, 302 – Cj 52 e 54 – Torre B – Vila Philippos Nakas S.A. The Music House MALAYSIA
Olímpia – CEP 04551-010 – São Paulo/SP, Brazil 19th klm. Leof. Lavriou 190 02 Peania – Attiki, Yamaha Music (Malaysia) Sdn. Bhd.
Tel: +55-11-3704-1377 Greece No.8, Jalan Perbandaran, Kelana Jaya, 47301
ARGENTINA Tel: +30-210-6686168 Petaling Jaya, Selangor, Malaysia
Yamaha Music Latin America, S.A., Tel: +60-3-78030900
SWEDEN/FINLAND/ICELAND
Sucursal Argentina Yamaha Music Europe GmbH Germany filial SINGAPORE
Olga Cossettini 1553, Piso 4 Norte, Scandinavia Yamaha Music (Asia) Private Limited
Madero Este-C1107CEK, JA Wettergrensgata 1, 400 43 Göteborg, Sweden Block 202 Hougang Street 21, #02-00,
Buenos Aires, Argentina Tel: +46-31-89-34-00 Singapore 530202, Singapore
Tel: +54-11-4119-7000 Tel: +65-6740-9200
DENMARK
PANAMA AND OTHER LATIN Yamaha Music Denmark, TAIWAN
AMERICAN COUNTRIES/ Fillial of Yamaha Music Europe GmbH, Tyskland Yamaha Music & Electronics Taiwan Co.,Ltd.
CARIBBEAN COUNTRIES Generatorvej 8C, ST. TH. , 2860 Søborg, Denmark 2F., No.1, Yuandong Rd., Banqiao Dist.,
Yamaha Music Latin America, S.A. Tel: +45-44-92-49-00 New Taipei City 22063, Taiwan (R.O.C.)
Edif. Torre Banco General, Piso 7, Urbanización Tel: +886-2-7741-8888
NORWAY
Marbella, Calle 47 y Aquilino de la Guardia, Yamaha Music Europe GmbH Germany - THAILAND
Ciudad de Panamá, República de Panamá Norwegian Branch Siam Music Yamaha Co., Ltd.
Tel: +507-269-5311 Grini Næringspark 1, 1332 Østerås, Norway 3, 4, 15, 16th Fl., Siam Motors Building,
Tel: +47-6716-7800 891/1 Rama 1 Road, Wangmai,
EUROPE Pathumwan, Bangkok 10330, Thailand
CYPRUS Tel: +66-2215-2622
THE UNITED KINGDOM/IRELAND Yamaha Music Europe GmbH
Yamaha Music Europe GmbH (UK) Siemensstrasse 22-34, 25462 Rellingen, Germany VIETNAM
Sherbourne Drive, Tilbrook, Milton Keynes, Tel: +49-4101-303-0 Yamaha Music Vietnam Company Limited
MK7 8BL, U.K. 15th Floor, Nam A Bank Tower, 201-203 Cach
RUSSIA Mang Thang Tam St., Ward 4, Dist.3,
Tel: +44-1908-366700 Yamaha Music (Russia) LLC. Ho Chi Minh City, Vietnam
GERMANY Room 37, entrance 7, bld. 7, Kievskaya street, Tel: +84-8-3818-1122
Yamaha Music Europe GmbH Moscow, 121059, Russia
Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +7-495-626-5005 OTHER ASIAN COUNTRIES
Tel: +49-4101-303-0 http://asia.yamaha.com/
OTHER EUROPEAN COUNTRIES
SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH
Yamaha Music Europe GmbH, Branch Siemensstrasse 22-34, 25462 Rellingen, Germany OCEANIA
Switzerland in Thalwil Tel: +49-4101-3030 AUSTRALIA
Seestrasse 18a, 8800 Thalwil, Switzerland Yamaha Music Australia Pty. Ltd.
Tel: +41-44-3878080 AFRICA Level 1, 80 Market Street, South Melbourne,
AUSTRIA/BULGARIA/ VIC 3205, Australia
Yamaha Music Gulf FZE Tel: +61-3-9693-5111
CZECH REPUBLIC/HUNGARY/ JAFZA-16, Office 512, P.O.Box 17328,
ROMANIA/SLOVAKIA/SLOVENIA Jebel Ali FZE, Dubai, UAE COUNTRIES AND TRUST
Yamaha Music Europe GmbH Tel: +971-4-801-1500 TERRITORIES IN PACIFIC OCEAN
Branch Austria http://asia.yamaha.com/
Schleiergasse 20, 1100 Wien, Austria MIDDLE EAST
Tel: +43-1-60203900
TURKEY
POLAND Yamaha Music Europe GmbH
Yamaha Music Europe GmbH Merkezi Almanya Türkiye İstanbul Şubesi
Sp.z o.o. Oddział w Polsce Maslak Meydan Sodak, Spring Giz Plaza Bagimsiz
ul. Wielicka 52, 02-657 Warszawa, Poland Böl. No:3, Sariyer Istanbul, Turkey
Tel: +48-22-880-08-88 Tel: +90-212-999-8010
MALTA OTHER COUNTRIES
Olimpus Music Ltd. Yamaha Music Gulf FZE
Valletta Road, Mosta MST9010, Malta JAFZA-16, Office 512, P.O.Box 17328,
Tel: +356-2133-2093 Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
PA50 Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan
(For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany
Manual Development Group

Yamaha Pro Audio global website © 2013 Yamaha Corporation
http://www.yamaha.com/proaudio/
Published 12/2017 POES-HO
Yamaha Downloads Printed in China
http://download.yamaha.com/
ZC11300

mtx3 en Om h0

Uploaded by

Copyright:

Available Formats

mtx3 en Om h0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

mtx3 en Om h0

Uploaded by

Copyright:

Available Formats

Owner’s Manual

The above warning is located on the top of the unit.

IMPORTANT SAFETY INSTRUCTIONS

2 MTX3 Owner’s Manual

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

IMPORTANT NOTICE FOR THE UNITED KINGDOM COMPLIANCE INFORMATION STATEMENT

ADVARSEL! NEDERLAND / THE NETHERLANDS

(lithium caution) (lithium disposal)

* This applies only to products distributed (Perchlorate) (class b korea)

MTX3 Owner’s Manual 3

Power supply/Power cord Water warning

Power supply/Power cord Maintenance

4 MTX3 Owner’s Manual PA_en_1 1/1

* Data items maintained in the internal memory by the backup

Information for users on collection and disposal of old equipment:

MTX3 Owner’s Manual 5

Introducing the MTX3.....................................................................................................8

Controls and Connectors ..............................................................................................9

Quick Guide ..................................................................................................................14

Various Procedures ......................................................................................................17

6 MTX3 Owner’s Manual

Included items (please check) Firmware versions

Precautions for rackmounting

MTX3 Owner’s Manual 7

Features About MTX-MRX Editor

• Newly-developed “YDIF” digital audio transmis-

8 MTX3 Owner’s Manual

q SD memory card slot !0 [NETWORK] indicator

w [INPUT PEAK] indicators 1–8 !2 [SCHEDULER] indicator

MTX3 Owner’s Manual 9

NOTE Up to eight control panels can be connected to one MTX3.

CAUTION i DIP switches

10 MTX3 Owner’s Manual

 Switches 1–2 (UNIT ID)  Switches 7–8 (START UP MODE)

Switch position Option Functions NOTE

MTX3 Owner’s Manual 11

 Euroblock plug connection 1. Loosen the terminal screws.

12 MTX3 Owner’s Manual

5. Plug the Euroblock plug into the [GPI] con-

MTX3 Owner’s Manual 13

7. The audio signal flow in the MTX3 and the

2. Install MTX-MRX Editor in your computer.

4. If you want to play back music or other audio

Output port settings (e.g., polarity, output gain)

14 MTX3 Owner’s Manual

8. Make DCP settings.

MTX3 Owner’s Manual 15

On-site work (Settings in MTX-MRX

1. Connect the computer to the MTX3/XMV/

2. Start up MTX-MRX Editor and load the proj-

3. Power-on the MTX3.

4. Power-on the XMV/EXi8/EXo8 and the analog

5. In the [To Device] direction, place the MTX3/

6. Check the presets.

7. Check the signal processing.

8. Adjust the output level of the MTX3 and the

9. Store the preset.

10. Save your settings and close MTX-MRX Edi-

16 MTX3 Owner’s Manual

YDIF DISTRIBUTIO N MODE only CASCADE MODE only 6 16