BRITISH STANDARD BS ISO

128-23:1999

Technical drawings —
General principles of
presentation —
Part 23: Lines on construction drawings
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

ICS 01.100.30

12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
 BS ISO 128-23:1999

National foreword
This British Standard reproduces verbatim ISO 128-23:1999 and implements
it as the UK national standard.
The UK participation in its preparation was entrusted by Technical Committee
B/212, Tolerances, drawing practice, modular co-ordination, joints, project
information and computer modelling, to Subcommittee B/212/2, Construction
drawing practice, which has the responsibility to:

— aid enquirers to understand the text;

— present to the responsible international/European committee any

enquiries on the interpretation, or proposals for change, and keep the
UK interests informed;
— monitor related international and European developments and
promulgate them in the UK.

A list of organizations represented on this subcommittee can be obtained on

request to its secretary.
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

Cross-references
The British Standards which implement international or European
publications referred to in this document may be found in the BSI Standards
Catalogue under the section entitled “International Standards Correspondence
Index”, or by using the “Find” facility of the BSI Standards Electronic
Catalogue.
A British Standard does not purport to include all the necessary provisions of
a contract. Users of British Standards are responsible for their correct
application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.

Summary of pages
This document comprises a front cover, an inside front cover, the ISO title page,
This British Standard, having pages ii to iv, pages 1 to 12, an inside back cover and a back cover.
been prepared under the
direction of the Sector The BSI copyright date displayed in this document indicates when the
Committee for Building and document was last issued.
Civil Engineering, was
published under the authority
of the Standards Committee
and comes into effect on
15 October 1999 Amendments issued since publication

Amd. No. Date Comments

© BSI 15 September 2002

ISBN 0 580 35143 2

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI
 ISO 128-23:1999

Contents

Page
Foreword iii
1 Scope 1
2 Normative references 1
3 General principles 1
4 Types of lines and their applications 1
5 Line widths 4
Annex A (informative) Examples of application 5
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

ii © BSI 15 September 2002

 ISO 128-23:1999

Foreword

ISO (the International Organization for Standardization) is a worldwide

federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that
committee. International organizations, governmental and non-governmental,
in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in
ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75% of the member bodies casting a vote.
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

International Standard ISO 128-23 was prepared by Technical Committee

ISO/TC 10, Technical drawings, product definition and related documentation,
Subcommittee SC 8, Construction documentation.
This first edition is based on ISO 128:1982, clause 3, and it replaces the rules
specified in that clause.
ISO 128 consists of the following parts, under the general title Technical
drawings — General principles of presentation:
— Part 20: Basic conventions for lines;
— Part 21: Preparation of lines by CAD systems;
— Part 22: Basic conventions and applications for leader lines and reference
lines;
— Part 23: Lines on construction drawings;
— Part 24: Lines on mechanical engineering drawings;
— Part 25: Lines on shipbuilding drawings;
— Part 30: Basic convention for views;
— Part 50: Basic conventions for representing areas on cuts and sections.
NOTE Further parts of ISO 128 are planned, covering other general principles of presentation
including those for application of lines within drawings of various technical fields.
Annex A of this part of ISO 128 is for information only.

© BSI 15 September 2002 iii

 ISO 128-23:1999

Introduction
The basic conventions and the application of lines in respect to other fields of
drawing practice are presented in other parts of ISO 128 since requirements in
industry vary considerably. For further information, see ISO 128-20.
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

iv © BSI 15 September 2002

 ISO 128-23:1999

1 Scope
This part of ISO 128 specifies types of lines and their application in construction documentation comprising
architectural drawings, structural engineering drawings, building service engineering drawings, civil
engineering drawings, landscape drawings and town planning drawings.

2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute
provisions of this part of ISO 128. For dated references, subsequent amendments to, or revisions of, any of
these publications do not apply. However, parties to agreements based on this part of ISO 128 are
encouraged to investigate the possibility of applying the most recent editions of the normative documents
indicated below. For undated references, the latest edition of the normative document referred to applies.
Members of ISO and IEC maintain registers of currently valid International Standards.
ISO 128-20:1996, Technical drawings — General principles of presentation — Part 20: Basic conventions
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

for lines.
ISO 129:1985, Technical drawings — Dimensioning — General principles, definitions, methods of execution
and special indications.
ISO 3766:1995, Construction drawings — Simplified representation of concrete reinforcement.
ISO 4068:1978, Building and civil engineering drawings — Reference lines.
ISO 4069:1977, Building and civil engineering drawings — Representation of areas on sections and views —
General principles.
ISO 4463-1:1989, Measurement methods for building — Setting-out and measurement — Part 1: Planning
and organization, measuring procedures, acceptance criteria.
ISO 6428:1982, Technical drawings — Requirements for microcopying.
ISO 7519:1991, Technical drawings — Construction drawings — General principles of presentation for
general arrangement and assembly drawings.
ISO 8048:1984, Technical drawings — Construction drawings — Representation of views, sections and cuts.
ISO 8560:1986, Technical drawings — Construction drawings — Representation of modular sizes, lines and
grids.
ISO 11091:1994, Construction drawings — Landscape drawing practice.

3 General principles
The types of lines, their designations and their dimensions as well as general rules for draughting of lines
are specified in ISO 128-20.
The requirements for microcopying are specified in ISO 6428.

4 Types of lines and their applications

The first part of the number is the number of line type in ISO 128-20.
Examples of applications are shown in Annex A.

© BSI 15 September 2002 1

 ISO 128-23:1999

Table 1 — Types of lines and their application

No. Description and Application Reference to
representation ISO
01.1 Continuous narrow line .1 boundaries of different materials in view, cut 7519
and section (alternatively, see 01.2.2)
.2 hatching 4069
.3 diagonals for indication of openings, holes and 7519
recesses
.4 arrow lines in stairs, ramps and sloping areas 7519
.5 modular grid lines, first stage (if necessary, 8560
other colour than outlines)
.6 short centrelines —
.7 extension lines 129
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

.8 dimension lines and their terminators 129

.9 leaderlines 129
.10 existing contours on landscape drawings 11091
(alternatively, see 02.1.1)
.11 visible outlines of parts in view (alternatively, —
see 01.2.3)
.12 simplified representation of doors, windows, 7519
stairs, fittings etc. (alternatively, see 01.2.4)
.13 framing of details —
Continuous narrow lines .14 limits of partial or interrupted views, cuts and —
with zigzags sections, if the limit is not a line 04.1
(alternatively, see 04.1.6)

01.2 Continuous wide line .1 visible outlines of parts in cut and section when 7519
hatching is used
.2 boundaries of different materials in view, cut —
and section (alternatively, see 01.1.1)
.3 visible outlines of parts in view (alternatively, 7519
see 01.1.11)
.4 simplified representation of doors, windows, 7519
stairs, fittings etc. (alternatively, see 01.1.12)
.5 modular grid lines, second stage (if necessary 8560
other colour than outlines)
.6 arrow lines for marking of views, cuts and 8048
sections
.7 proposed contours on landscape drawings 11091
01.3 Continuous extra-wide .1 visible outlines of parts in cut and section when 7519
line hatching is not used
.2 reinforcing bars (see 02.3.1) 3766
.3 lines of special importance —
02.1 Dashed narrow line .1 existing contours on landscape drawings 11091
(alternatively, see 01.1.10)
.2 subdivision of plant beds/grass 11091
.3 hidden outlines (alternatively, see 02.2.1) —
02.2 Dashed wide line .1 hidden outlines (alternatively, see 02.1.3) —

2 © BSI 15 September 2002

 ISO 128-23:1999

Table 1 — Types of lines and their application (continued)

No. Description and Application Reference to
representation ISO
02.3 Dashed extra-wide line .1 reinforcing bars in bottom layer on plan and far 3766
face layer in elevation when bottom and top
layers and near and far face layers are shown on
the same sketch
04.1 Long dashed dotted .1 cutting planes (line 04.2 at ends and changes of —
narrow line direction)
.2 centrelines —
.3 lines of symmetry (identified at the ends by two —
narrow short parallel lines drawn at right angle)
.4 framing of enlarged details —
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

.5 reference lines —
.6 limits of partial or interrupted views, cuts and —
sections (especially for short lines and in narrow
situations; see examples 01.1.2, 01.2.1, 01.3.1,
etc., in Annex A; alternatively, see 01.1.14)
04.2 Long dashed dotted wide .1 cutting planes (at ends and changes of direction; —
line see 04.1.1)
.2 outlines of visible parts situated in front of the —
cutting plane
04.3 Long dashed dotted extra- .1 secondary lines for setting out and arbitrary 4463-1;4068
wide line reference lines
.2 indication of lines or surfaces to which a special —
requirement applies
.3 boundary lines for contracts, stages, zones etc. —
05.1 Long dashed double- .1 alternative and extreme positions of movable —
dotted narrow line parts
.2 centroidal line —
.3 outlines of adjacent parts —
05.2 Long dashed double- .1 outlines of hidden parts situated in front of the —
dotted wide line cutting plane

05.3 Long dashed double- .1 reinforcing prestressed bars and cables 3766
dotted extra-wide line

07.1 Dotted narrow line .1 outlines of parts not included in the project -

© BSI 15 September 2002 3

 ISO 128-23:1999

5 Line widths
On a construction drawing three line widths, narrow, wide and extra-wide, are normally used (see Table 2).
The proportions between the line widths are 1:2:4.
A special line width is used for representation and lettering of graphical symbols. This line width is
situated between the width of the narrow and the wide line.
Table 2 — Line widths
Dimensions in millimetres
Line group Narrow line Wide line Extra-wide line Line widths for
graphical symbols
0,25 0,13 0,25 0,5 0,18
0,35 0,18 0,35 0,7 0,25
0,5 0,25 0,5 1 0,35
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

0,7 0,35 0,7 1,4 0,5

1 0,5 1 2 0,7
The line widths shall be chosen according to the type, size and scale of the drawing and the requirements
at microcopying and other methods of reproduction.

4 © BSI 15 September 2002

 ISO 128-23:1999

Annex A (informative)
Examples of application
Examples of the application of the different types of lines, along with the corresponding reference numbers
from clause 4, are given in Table A.1.
Table A.1 — Examples of application
No. Line type Example of application
01.1 Continuous narrow line
01.1.1 Boundaries of different materials
in view, cut and section
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

01.1.2 Hatching

01.1.3 Diagonals for indication of

openings, holes and recesses

01.1.4 Arrow lines in stairs, ramps and

sloping areas

© BSI 15 September 2002 5

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
01.1.5 Modular grid lines, first stage

01.1.6 Short centrelines

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

01.1.7 Extension lines

01.1.8 Dimension lines and their
terminators
01.1.9 Leader lines

01.1.10 Existing contours on landscape

drawings

01.1.11 Visible outlines of parts in view

(alternatively, see 01.2.3)

01.1.12 Simplified representation of doors,

windows, stairs, fittings etc.
(alternatively, see 01.2.4)

6 © BSI 15 September 2002

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
01.1.13 Framing of details

01.1.14 Limits of partial or interrupted

views, cuts and sections, if the limit
is not a line 04.1
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

01.2 Continuous wide line

01.2.1 Visible outlines of parts in cut and
section when hatching is used

01.2.2 Boundaries of different materials

in view, cut and section

01.2.3 Visible outlines of parts in view

(alternatively, see 01.1.11)

© BSI 15 September 2002 7

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
01.2.4 Simplified representation of doors,
windows, stairs, fittings etc.
(alternatively, see 01.1.12)

01.2.5 Modular grid lines, second stage

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

01.2.6 Arrow lines for marking of views,

cuts and sections

01.2.7 Proposed contours on landscape

drawings

01.3 Continuous extra-wide line

01.3.1 Visible outlines of parts in cut and
section when hatching is not used

01.3.2 Reinforcing bars

8 © BSI 15 September 2002

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
02.1 Dashed narrow line
02.1.1 Existing contours on landscape
drawings (alternatively, see
01.1.10)

02.1.2 Subdivision of plant beds/grass

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

02.2 Dashed wide line

02.2.1 Hidden outlines

02.3 Dashed extra-wide line

02.3.1 Reinforcing bars in bottom layer on
plan and far face layer in elevation
when bottom and top layers are
shown on the same sketch

04.1 Long dashed dotted narrow

line
04.1.1 Cutting planes (drawn with line
04.2 at ends and changes of
direction)

© BSI 15 September 2002 9

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
04.1.2 Centrelines

04.1.3 Lines of symmetry

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

04.1.4 Framing of enlarged details

04.1.5 Reference lines

04.2 Long dashed dotted wide line

04.2.1 Cutting planes (drawn with line
04.2 at ends and changes of
direction; the rest is drawn with
line 04.1)

10 © BSI 15 September 2002

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
04.2.2 Outlines of visible parts situated in
front of the cutting plane

04.3 Long dashed dotted extra-wide

line
04.3.1 Secondary lines for setting out and
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

arbitrary reference lines

04.3.2 Indication of lines or surfaces to

which a special requirement
applies

04.3.3 Boundary lines for contracts,

stages, zones, etc.

05.1 Long dashed double-dotted

narrow line
05.1.1 Alternative and extreme position of
movable parts

© BSI 15 September 2002 11

 ISO 128-23:1999

Table A.1 — Examples of application (continued)

No. Line type Example of application
05.1.2 Centroidal lines

05.1.3 Outlines of adjacent parts

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

05.2 Long dashed double-dotted

wide line
05.2.1 Outlines of hidden parts situated in
front of the cutting plane

05.3 Long dashed double-dotted

extra-wide line
05.3.1 Reinforcing prestressed bars and
cables

07 Dotted narrow line

07.1 Outlines of parts not included in
the project

12 © BSI 15 September 2002

Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

blank
 BS ISO
128-23:1999
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.

Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.

Buying standards
Licensed copy:University of Cambridge, 05/10/2016, Uncontrolled Copy, © BSI

Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.

Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.

Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL