VLT 2800 Series

Data sheet

VLT 2800

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

This section makes it easier for you to specify and
order a VLT 2800.

Choice of frequency converter

The frequency converter must be chosen on the basis of the present motor current at maximum loading
of the unit. The frequency converters rated output
current I INV. must be equal to or greater than the required motor current.

Mains voltage
VLT 2800 is available for two mains voltage ranges:
200-240 V and 380-480 V.

Select whether the frequency converter is connected

to a mains voltage of:
- 1 x 220 - 240 V single-phase AC voltage
- 3 x 200 - 240 V three-phase AC voltage
- 3 x 380 - 480 V three-phase AC voltage

1 x 220 - 240 Volt mains voltage

Type
2803
2805
2807
2811
2815

Typical shaft output

P INV.
[kW]
0.37
0.55
0.75
1.1
1.5

[HP]
0.5
0.75
1.0
1.5
2.0

Max. constant output current

IINV.
[A]
2.2
3.2
4.2
6.0
6.8

Max. constant output power

at 230 V SINV.
[kVA]
0.9
1.3
1.7
2.4
2.7

[HP]
0.5
0.75
1.0
1.5
2.0
3.0
5.0

Max. constant output current

IINV.
[A]
2.2
3.2
4.2
6.0
6.8
9.6
16.0

Max. constant output power

at 230 V SINV.
[kVA]
0.9
1.3
1.7
2.4
2.7
3.8
6.4

3 x 200 - 240 Volt mains voltage

Type
2803
2805
2807
2811
2815
2822
2840

Typical shaft output

PINV.
[kW]
0.37
0.55
0.75
1.1
1.5
2.2
3.7

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

3 x 380 - 480 Volt mains voltage

Type
2805
2807
2811
2815
2822
2830
2840
2855
2875
2880
2881
2882

Typical shaft output

P INV.
[kW]
0.55
0.75
1.1
1.5
2.2
3.0
4.0
5.5
7.5
11
15
18.5

[HP]
0.75
1.0
1.5
2.0
3.0
4.0
5.0
7.5
10.0
15
20
25

Max. constant output current

IINV.
[A]
1.7
2.1
3.0
3.7
5.2
7.0
9.1
12.0
16.0
24
32
37.5

Max. constant output power

at 400 V SINV.
[kVA]
1.1
1.7
2.0
2.6
3.6
4.8
6.3
8.3
11.1
16.6
22.2
26.0

FC protocol
Danfoss VLT frequency converters are able to fulfill
RFI filter
many different functions in a monitoring system. The
VLT 2800 is available with or without an integral 1A
frequency converter can be integrated directly in an
RFI-filter. The integral 1A RFI filter complies with
overall surveillance system, which will allow detailed
EMC standards EN 55011-1A.
process data to be transferred via serial communication.
With an integral RFI filter there is compliance with EN
The protocol standard is based on an RS 485 bus
55011-1B with a max. 15-metre screened/armoured
system with a maximum transmission speed of 9600
motor cable on VLT 2803-2815 1 x 220-240 Volt.
baud. The following Drive profiles are supported as
standard:
- FC Drive, which is a profile adapted to Danfoss.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

Data sheet

VLT 2880-82 with integral 1B filter comply with EMC

Enclosure
standard EN 50011 - 1B
All VLT 2800 units are supplied with IP 20 enclosure
as standard.
This enclosure level is ideal for panel mounting in areas where a high degree of protection is required; at
Harmonic filter
the same time IP 20 enclosures allow side-by-side
The harmonic currents do not affect power consumpinstallation without any need for extra cooling equiption directly, but they increase the heat losses in the
ment.
installation (transformer, cables). That is why, in a
IP 20 units can be upgraded to NEMA 1 by fitting a
system with a relatively high percentage of rectifier
terminal cover. See ordering number for terminal
load, it is important to keep the harmonic currents at
cover under Accessories for VLT 2800.
a low level so as to avoid a transformer overload and
high cable temperature. For the purpose of ensuring
In addition, VLT 2880-82 units are supplied with
low harmonic currents, VLT 2822 3 x 200-240 V and
Nema 1 enclosure as standard.
VLT 2805-2882 380-480 V are fitted with coils in
their intermediate circuit as standard. This reduces
the input current I RMS by typically 40 %.
Brake
Please note that 1 x 220-240 V units are not supVLT 2800 is available with or without an integral
plied with coils in their intermediate circuit.
brake module. See also the section entitled Brake
resistors for ordering a Brake resistor.

VLT 2800 Series

-

Profidrive, which supports the profidrive profile

See Serial communication for VLT 2800 for further

details of telegram structure and Drive profile.

Fieldbusoption
The increasing information requirements in industry
make it necessary to collect or visualize many different process data. Important process data help the
system technician with the daily monitoring of the
system. The large amounts of data involved in major
systems make a higher transmission speed than
9600 baud desirable.
Profibus
Profibus is a fieldbus system, which can be used for
linking automation devices such as sensors and
actuators with the controls by means of a twoconductor cable. Profibus DP is a very fast
communication protocol, made specially for communication between the automation system and various
types of equipment.
Profibus is a registered trade mark.
DeviceNet
DeviceNet fieldbus systems can be used for linking
automation devices such as sensors and actuators
with the controls by means of a fourwire conductor
cable.
DeviceNet is a medium speed communication protocol, made specially for communication between the
automation system and various types of equipment.
Units with DeviceNet protocol cannot be controlled
by FC protocol and Profidrive protocol.
VLT Software Dialog can be used on the Sub D plug.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Technical data for VLT 28032875 Motor coils

Max. cable length (unscreened/unarmoured) 1 )
Max. cable length (screened/armoured) 1 )
Enclosure
Max. rated current 1 )
Max. voltage1 )
Min. distance between VLT and motor coil
Min. distance above and below motor coil
Dimensions H x W x D (mm)
Weight
1 )

Parameter 411 Switching frequency = 4500 Hz.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

100 metres of screened/armoured motor cable. The

motor coil module has an enclosure of IP 20 and
can be installed side-by-side.

200 m
100 m
IP 20
16 A
480 V AC
Side-by-side
100 mm
200 x 90 x 152
3.8 kg

Data sheet

Motor coils
By fitting the motor coil module between the VLT
2800 and the motor it is possible to use up to 200
metres of unscreened/unarmoured motor cable or

See ordering number for motor coil module under

Accessories for VLT 2800.

VLT 2800 Series

RFI 1B filter
All frequency converters will cause electromagnetic
noise in the mains supply when they are operating.
An RFI (Radio Frequency Interference) filter will reduce the electromagnetic noise in the mains supply.
Without an RFI filter there is a risk that a frequency
converter will disrupt other electrical components
that are connected to the mains and might thus
cause operating disruption.

Technical data for VLT 28032875 RFI 1B filter

Max. cable length (screened/armoured) 200-240 V
Max. cable length (screened/armoured) 380-480 V
Enclosure
Max. rated current
Max. Voltage
Max. voltage to earth
Min. distance between VLT and RFI 1B filter
Min. distance above and below RFI 1B filter
Dimensions H x W x D (mm)
Weight

By fitting an RFI 1B filter module between the mains

supply and the VLT 2800, the VLT 2800 complies
with the EMC norm EN 55011-1B.
NB!:
To comply with EN 55011-1B the RFI 1B filter module must be fitted together with a VLT
2800 with integral 1A RFI filter.

100 m (At 1A: 100 m)

25 m (At 1A: 50 m)
IP 20
16 A
480 V AC
300 V AC
Side-by-Side
100 mm
200 x 60 x 87
0.9 kg

See ordering number for RFI 1B filter module under

Accessories for VLT 2800.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

RFI 1B/LC filter
The RFI 1B/LC filter contains both an RFI module
that complies with EN 55011-1B and an LC filter that
reduces the acoustic noise.
LC filter

When a motor is controlled by a frequency converter, at times you will be able to hear the acoustic
noise from the motor. The noise, which is caused by
the design of the motor, is generated every time one
of the inverter contacts in the frequency converter is
activated. The frequency of the acoustic noise therefore corresponds to the frequency converters
connection frequency.
The filter reduces the voltages du/dt, the peak voltage Upeak and ripple current I to the motor, so that
the current and voltage are almost sine-shaped. The
acoustic motor noise is thus reduced to a minimum.

Installation of thermistor (PTC)

The RFI 1B/LC filter has an integral thermistor
(PTC), which is activated if an overtemperature
arises. The frequency converter can be programmed
to stop the motor and activatee an alarm via a relay
output or a digital output if the thermistor is activated.

The thermistor must be connected between terminal

50 (+10V) and one of the digital inputs 18, 19, 27
and 29.
In parameter 128 Motor thermal protection Thermistor warning [1] or Thermistor trip [2] are selected
The thermistor is connected as follows:

Because of the ripple current in the coils some noise

will be emitted by the coils. This problem can be
solved completely by fitting the filter inside a cabinet
or equivalent.

Data sheet

Danfoss can supply an LC filter for the VLT series

2800, which muffles the acoustic motor noise . Before the filters are put into use you must ensure that:
- rated current is observed
- mains voltage is 200-480 V
- parameter 412 Variable switching frequency is set
to LC filter attached [3]
- output frequency is max. 120 Hz
See drawing on the next page.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

RFI 1B/LC filter
NB!:
To comply with EN 55011-1B the RFI 1B filter
module must be fitted to a VLT 2800 with integral 1A RFI filter.

NB!:
The 1B/LC filter is not suitable for 200
V devices due to the high 1 input current.

Technical data for VLT 28032840 RFI 1B/LC filter

Max. cable length (screened/armoured) 380-480 V
25 m (At 1A: 50 m)
Enclosure
IP 20
Max. rated current
4.0 (Order no.: 195N3100); 9.1 (Order no.:
195N3101)
Max. voltage
480 V AC
Max. voltage to earth
300 V AC
Min. distance between VLT and RFI 1B/LC filter
Side-by-Side
Min. distance above and below RFI 1B/LC filter
100 mm
Dimensions 195N3100 4.0 A H x W x D (mm)
200 x 75 x 168
Dimensions 195N3101 9.1 A H x W x D (mm)
267.5 x 90 x 168
Weight 195N3100 4.0 A
2.4 kg
Weight 195N3101 9.1 A
4.0 kg

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Control unit
VLT 2800 is always supplied with an integral control
unit.
All displays are in the form of a six-digit LED display
capable of showing one item of operating data continuously during normal operation. As a supplement
to the display, there are three indicator lamps for
voltage (ON), warning (WARNING) and alarm
(ALARM). Most of the frequency converters parameter Setups can be changed immediately via the
integral control panel.

Data sheet

An LCP2 control panel to be connected via a plug to

the front of the frequency converter is available as
an option. The LCP2 control panel can be installed
up to 3 metres away from the frequency converter,
e.g. on a front panel, by means of the accompanying mounting kit.
All displays of data are via a 4-line alpha-numerical
display, which in normal operation is able to show 4
operating data items and 3 operation modes continuously. During programming, all the information
required for quick, efficient parameter Setup of the
frequency converter is displayed. As a supplement
to the display, there are three indicator lamps for
voltage (ON), warning (WARNING) and alarm
(ALARM). Most of the frequency converters parameter Setups can be changed immediately via the
LCP2 control panel. See also the section entitled
The LCP2 control unit in the Design Guide.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Ordering numbers for VLT 2800 200-240V

1,1 kW
RFI

0,37 kW
RFI

Unit

ST

VLT 2803 1/3 x 200-240 V

Profibus

Profibus DP

ST

195N0037

SB

195N0038

R1

ST

195N0039

195N0001

R1

SB

195N0040

195N0041

195N0042

195N0043

SB

195N0002

ST

ST

195N0003

SB

R1

SB

195N0004

R1

ST

ST

195N0005

R1

SB

X
X
X
X

SB

195N0006

ST

195N0007

SB

195N0008

R1

ST

195N0009

R1

SB

Unit

Profibus DP

R1

ST

R1

SB

ST

SB

R1

ST

R1

SB

0,55 kW
RFI

Unit

X
X
X
X

DeviceNet

195N0011

1,5 kW

195N0012

RFI

Ordering no.

DP

195N0049

195N0050

R1

ST

195N0051

R1

SB

195N0052

195N0053

195N0054

195N0055

R1

ST

195N0015

R1

ST

R1

SB

195N0016

R1

SB

X
X
X
X

ST

195N0017

ST

195N0018

SB

195N0019

R1

ST

195N0020

R1

SB

Unit

Profibus DP

195N0013

ST

195N0014

SB

SB
ST

SB

R1

ST

R1

SB

X
X
X
X

Ordering no.

DeviceNet

R1

195N0048

ST

ST

195N0047

SB

ST

SB

195N0046

SB

195N0044
195N0045

R1

X
X
X
X

VLT 2815 1/3 x 200-240 V

X
X
X
X

195N0010

VLT 2805 1/3 x 200-240 V

Profibus

Ordering no.

Ordering no.

R1

X
X
X
X

DeviceNet

DeviceNet

DP
-

VLT 2811 1/3 x 200-240 V

Unit

X
X
X
X

195N0056
195N0057
195N0058
195N0059
195N0060

195N0021
195N0022

2,2 kW

195N0023

RFI

195N0024

ST

195N0061

SB

195N0062

VLT 2822 3 x 200-240 V

DeviceNet

Ordering no.

0,75 kW

VLT 2807 1/3 x 200-240 V

R1

ST

195N0063

RFI

Unit

Profibus DP

DeviceNet

Ordering no.

R1

SB

195N0064

ST

195N0025

ST

195N0065

195N0026

SB

195N0066

195N0067

R1

ST

195N0027

R1

ST

R1

SB

195N0028

R1

SB

X
X
X
X

ST

195N0029

ST

195N0030

SB

195N0031

R1

ST

195N0032

R1

SB

SB

SB

R1

ST

R1

SB

X
X
X
X

ST

SB

R1

ST

R1

SB

10

X
X
X
X

X
X
X
X

195N0068
195N0069
195N0070
195N0071
195N0072

195N0033
195N0034
195N0035
195N0036

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

3,7 kW
RFI

VLT 2840 3 x 200-240 V

Unit

Profibus DP

DeviceNet

Ordering no.

ST

195N0073

SB

195N0074

R1

ST

195N0075

R1

SB

195N0076

195N0077

195N0078

195N0079

R1

ST

R1

SB

X
X
X
X

ST

ST

SB

SB

R1

ST

R1

SB

X
X
X
X

195N0080
195N0081
195N0082
195N0083
195N0084

ST: Standard unit.

SB: Standard unit with integral brake.
R1: With RFI filter that complies with EN 55011-1A.

Data sheet

NB!:
For VLT 2803-2815 220-with an R1 filter it is
only possible to connect single-phase mains
voltage 1 x 220 - 240 Volt.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

11

VLT 2800 Series

Ordering numbers for VLT 2800 380-480V

1,5 kW
RFI

0,55 kW

VLT 2805 3 x 380-480 V

RFI

Profibus DP

Unit

DeviceNet

VLT 2815 3 x 380-480 V

Unit

Profibus DP

DeviceNet

Ordering no.

ST

195N1037

Ordering no.

SB

195N1038

ST

195N1001

R1

ST

195N1039

SB

195N1002

R1

SB

195N1040

195N1041

195N1042

195N1043

R1

ST

195N1003

ST

R1

SB

195N1004

SB

195N1005

R1

ST

195N1006

R1

SB

X
X
X
X

195N1007

ST

ST

SB

R1

ST

R1

SB

X
X
X
X

ST

SB

R1

ST

R1

SB

X
X
X
X

195N1008

SB

195N1009

R1

ST

195N1010

R1

SB

Unit

Profibus DP

VLT 2807 3 x 380-480 V

RFI

Profibus DP

Unit

DeviceNet

X
X
X
X

195N1044
195N1045
195N1046
195N1047
195N1048

195N1011
195N1012

2,2 kW
RFI

0,75 kW

VLT 2822 3 x 380-480 V

DeviceNet

Ordering no.

ST

195N1049

Ordering no.

SB

195N1050

ST

195N1013

R1

ST

195N1051

SB

195N1014

R1

SB

195N1052

195N1053

195N1054

195N1055

R1

ST

195N1015

ST

R1

SB

195N1016

SB

195N1017

R1

ST

195N1018

R1

SB

X
X
X
X

195N1019

ST

ST

SB

R1

ST

R1

SB

X
X
X
X

ST

SB

R1

ST

R1

SB

X
X
X
X

195N1020

SB

195N1021

R1

ST

195N1022

R1

SB

Unit

Profibus DP

RFI

195N1024

VLT 2811 3 x 380-480 V

Unit

Profibus DP

DeviceNet

X
X
X
X

195N1056
195N1057
195N1058
195N1059
195N1060

195N1023
3,0 kW
RFI

1,1 kW

VLT 2830 3 x 380-480 V

DeviceNet

Ordering no.

ST

195N1061

Ordering no.

SB

195N1062

ST

195N1025

R1

ST

195N1063

SB

195N1026

R1

SB

195N1064

195N1065

195N1066

195N1067

R1

ST

195N1027

ST

R1

SB

195N1028

SB

195N1029

R1

ST

195N1030

R1

SB

X
X
X
X

195N1031

ST

ST

SB

R1

ST

R1

SB

X
X
X
X

ST

SB

R1

ST

R1

SB

12

X
X
X
X

195N1032

SB

195N1033

R1

ST

195N1034

R1

SB

X
X
X
X

195N1068
195N1069
195N1070
195N1071
195N1072

195N1035
195N1036

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

RFI

VLT 2840 3 x 380-480 V

Unit

Profibus DP

DeviceNet

11 kW
Ordering no.

RFI

VLT 2880 3 x 380-480 V

Unit

Profibus DP

DeviceNet

Ordering no.

ST

195N1073

ST

195N1109

SB

195N1074

SB

195N1110

R1

ST

195N1075

R3

ST

195N1111

R1

SB

195N1076

R3

SB

195N1112

195N1077

ST

195N1113

195N1078

SB

195N1114

195N1079

R3

ST

195N1115

195N1080

R3

SB

X
X
X
X

195N1081

ST

195N1082

SB

195N1083

R3

ST

195N1084

R3

SB

RFI

Unit

Profibus DP

DeviceNet

ST

195N1121

SB

195N1122

195N1123

195N1124

195N1125

195N1126

195N1127

195N1128

R1

ST

R1

SB

X
X
X
X

ST

ST

SB

SB

R1

ST

R1

SB

X
X
X
X

ST: Standard unit.

SB: Standard unit with integral brake.
R1: With RFI filter that complies with EN 55011-1A.
5,5 kW

VLT 2855 3 x 380-480 V

15 kW

Unit

Profibus DP

DeviceNet

Ordering no.

R3

ST

ST

195N1085

R3

SB

SB

195N1086

ST

R1

ST

195N1087

SB

R1

SB

195N1088

ST

ST

195N1089

R3

SB

SB

195N1090

ST

R1

ST

195N1091

SB

R1

SB

X
X
X
X

R3

195N1092

R3

ST

ST

195N1093

R3

SB

SB

R1

ST

R1

SB

7,5 kW
RFI

Profibus DP

DeviceNet

195N1096

Ordering no.

ST

195N1097

SB

195N1098

R1

ST

195N1099

R1

SB

195N1100

ST

195N1101

SB

195N1102

R1

ST

195N1103

R1

SB

X
X
X
X

ST

SB

R1

ST

R1

SB

195N1118
195N1119
195N1120

X
X
X
X

X
X
X
X

Ordering no.

195N1129
195N1130
195N1131
195N1132

195N1095

X
X
X
X

195N1116
195N1117

195N1094

VLT 2875 3 x 380-480 V

Unit

X
X
X
X

VLT 2881 3 x 380-480 V

RFI

X
X
X
X

195N1104
195N1105
195N1106

18.5 kW

VLT 2882 3 x 380-480 V

RFI

Unit

Profibus DP

DeviceNet

ST

195N1133

SB

195N1134

Ordering no.

R3

ST

195N1135

R3

SB

195N1136

ST

195N1137

195N1138

195N1139

SB

R3

ST

R3

SB

X
X
X
X

ST

SB

R3

ST

R3

SB

195N1107

X
X
X
X

195N1140

Data sheet

4,0 kW

195N1141
195N1142
195N1143
195N1144

195N1108

MD.28.A5.02 - VLT is a registered Danfoss trade mark

ST:
SB:
R1:
R3:

Standard
Standard
With RFI
With RFI

unit.
unit with integral brake.
filter that complies with EN 55011-1A.
filter that complies with EN 55011-1B

13

VLT 2800 Series

Brake resistors
Flatpack brake resistors IP 54

Type
2803
2805
2807
2811
2815
2822
2840
2805
2807
2811
2815
2822
2830
2840

(200
(200
(200
(200
(200
(200
(200
(400
(400
(400
(400
(400
(400
(400

V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)

P motor
[kW]
0.37
0.55
0.75
1.10
1.50
2.20
3.70
0.55
0.75
1.10
1.50
2.20
3.00
4.00

RMIN
[
]
297
198
135
99
69
43
21
747
558
387
297
198
135
99

Size [
] / [W]
per item
330
/ 100 W
220
/ 100 W
150
/ 100 W
100
/ 100 W
72
/ 200 W
50
/ 200 W
50
/ 200 W
830
/ 100 W
620
/ 100 W
430
/ 100 W
310
/ 200 W
210
/ 200 W
150
/ 200 W
240
/ 200 W

Duty cycle %
30
20
14
8
16
9
11
20
14
8
16
9
5.5
11

Order no.
175Uxxxx
1003
1004
1005
1006
0992
0993
2x09931
1000
1001
1002
0984
0987
0989
2x09861

These two resistors must be connected in parallel.

See dimensions of Flatpack brake resistors on the
next page
Coiled wire brake resistors with KLIXON switch, Duty-cycle 40%

Type
2803
2805
2807
2811
2815
2822
2840
2805
2807
2811
2815
2822
2830
2840
2855
2875
2880
2881
2882

(200
(200
(200
(200
(200
(200
(200
(400
(400
(400
(400
(400
(400
(400
(400
(400
(400
(400
(400

V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)
V)

Pmotor
[kW]
0.37
0.55
0.75
1.10
1.50
2.20
3.70
0.55
0.75
1.10
1.50
2.20
3.00
4.00
5.50
7.50
11.00
15.00
18.50

RMIN
[
]
297
198
135
99
74
50
22
747
558
387
297
198
135
99
80
56
40
30
25

RREC = Recommended brake resistor.

Ppeak = Max. brake effect at 160% brake torque.
Pavg = Mean power based on Duty-cycle.
14

RREC
[
]
330
220
150
110
82
56
25
830
620
430
330
220
150
110
80
56
40
30
25

Ppeak
[kW]
0.44
0.66
0.90
1.10
1.80
2.60
4.50
0.60
0.90
1.32
1.80
2.60
3.60
4.00
5.50
7.50
11.00
15.00
18.50

Pavg.
[kW]
0.18
0.26
0.36
0.44
0.72
1.06
1.80
0.25
0.36
0.53
0.72
1.06
1.44
1.60
2.20
3.00
5.00
9.30
12.70

Order no.
175U0xxx
900
901
902
975
903
904
925
976
910
911
912
913
914
979
977
978
997
998
999

See dimensions of Coiled wire brake resistors in instructions MI.50.D2.XX.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Data sheet

Order form

MD.28.A5.02 - VLT is a registered Danfoss trade mark

15

VLT 2800 Series

PC software and serial communication
Danfoss offers various options for serial communication. Using serial communication, it is possible to
monitor, program and control one or several frequency converters from a centrally located computer.
In addition, all VLT 2800 have an RS 485 port as
standard, thereby enabling communication e.g. with
a PC. For this purpose, a program called VLT Software Dialog is available.
VLT Software Dialog comes in three modules, as a
minimum containing the programs of the Basic module.

The logging module covers:

LOGGING is used for collecting and displaying historical or real-time operating data.
- presentation of selected parameters from several
frequency converters in the form of graphs.
- collection of log data for file.
- option of DDE link, e.g. to spreadsheet.
MODEM SETUP is used to set up the frequency converters modem. The module sets up the frequency
converters modem via the PCs communication port.
The template module covers:
TEMPLA TE SETUP is used for setting up template
files for PARAMETER SETUP.
- the template file acts as a screen that limits the
number of accessible parameters when a parameter file is to be made or edited in PARAMETER
SETUP
- the template file may contain preset values for
the parameters of the frequency converter
NB!:
The Logging and Template modules call for
the Basic module to be installed on the same
PC.

The Basic module covers:

TEST RUN used for controlling and running in a frequency converter, including
- Setting of reference value.
- simultaneous showing of selected parameters in
the form of graphs.
- option of DDE link, e.g. to spreadsheet.

Guided tour covers:

Guided tour offers a demonstration of the VLT Software Dialog program.

PARAMETER SETUP is used for setting up and

transmitting parameter sets, including:
- setting of frequency converter parameters.
- parameter sets can be collected from and copied
to a frequency converter.
- documentation / setup print incl. charts.
HISTORY where the different development stages of
VLT Software dialog can be studied.
BUS ADDRESS SETUP is used only for addressing
VLT 2800.

16

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Mechanical dimensions
The drawings below give the mechanical dimensions. All dimensions are in mm.

VLT 2840 200-240 Volt

VLT 2855-2875 380-480 Volt

VLT 2803-2815 200-240 Volt

VLT 2805-2815 380-480 Volt

VLT 2880-82 380-480V

Data sheet

VLT 2822 200-240 Volt

VLT 2822-2840 380-480 Volt

MD.28.A5.02 - VLT is a registered Danfoss trade mark

17

VLT 2800 Series

Terminal cover
The drawing below gives the dimensions for NEMA 1
terminal covers for VLT 2803-2875.
Dimension a depends on the unit type.

18

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Electrical installation

Data sheet

VLT 2803-2815 200-240 V, 2805-2815 380-480 V

MD.28.A5.02 - VLT is a registered Danfoss trade mark

19

VLT 2800 Series

VLT 2822 200-240 V, 2822-2840 380-480 V

20

VLT 2840 200-240 V, 2855-2875 380-480 V

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

VLT 2880-82 380-480V

Data sheet

Please note, that the units will be supplied with two

bottom plates; one for metric glands and one for
conduits.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

21

VLT 2800 Series

Electrical installation, control terminals

See section entitled Earthing of screened/armoured
control cables in the Design Guide for the correct
termination of control cables.

No.
01-03
12
18-33
20, 55
42
461

50
53
60
671
68,
691
701

Function
Relay outputs 01-03 can be used for
indicating status and alarms/warnings.
24 V DC voltage supply.
Digital inputs.
Common frame for input
and output terminals.
Analog output for displaying frequency,
reference, current or torque.
Digital output for displaying status,
warnings or alarms, as well as
frequency output.
+10 V DC supply
voltage for potentiometer or thermistor.
Analogue voltage input 0 - 10 V DC.
Analogue current input 0/4 - 20 mA.
+ 5 V DC supply voltage
to Profibus.
RS 485, Serial communication.
Frame for terminals 67, 68 and 69.
Normally this terminal is not to be used.

1. The terminals are not valid for DeviceNet/

CANopen. See also the DeviceNet manual,
MG.90.BX.YY for further details.

22

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

General technical data
Mains supply (L1, L2, L3):
Supply voltage VLT 2803-2815 220-240 V (N, L1) ....................................................... 1 x 220/230/240 V 10%
Supply voltage VLT 2803-2840 200-240 V ..................................................... 3 x 200/208/220/230/240 V 10%
Supply voltage VLT 2805-2882 380-480 V ..................................................... 3 x 380/400/415/440/480 V 10%
Supply frequency .................................................................................................................................... 50/60 Hz
Max. imbalance on supply voltage ...................................................................... 2.0% of rated supply voltage
True Power Factor ( ) ................................................................................................. 0.90 nominal at rated load
Displacement Power Factor (cos ') ........................................................................................ near unity (> 0.98)
Number of connections at supply input L1, L2, L3 .......................................................................... 2 times/min.
Max. short-circuit value ........................................................................................................................ 100,000 A
See Special Conditions section in the Design Guide
Output data (U, V, W):
Output voltage ............................................................................................................ 0 - 100% of supply voltage
Output frequency ......................................................................................................... 0.2 - 132 Hz, 1 - 1000 Hz
Rated motor voltage, 200-240 V units ............................................................................. 200/208/220/230/240 V
Rated motor voltage, 380-480 V units ...................................................................... 380/400/415/440/460/480V
Rated motor frequency ........................................................................................................................... 50/60 Hz
Switching on output ................................................................................................................................ Unlimited
Ramp times ................................................................................................................................. 0.02 - 3600 sec.
Torque characteristics:
Starting torque (parameter 101 Torque characteristic = Constant torque) .................................. 160% in 1 min. *
Starting torque (parameter 101 Torque characteristics = Variable torque) ................................. 160% in 1 min.*
Starting torque (parameter 119 High starting torque) ............................................................. 180% for 0.5 sec.*
Overload torque (parameter 101 Torque characteristic = Constant torque) ............................................... 160%*
Overload torque (parameter 101 Torque characteristic = Variable torque) ................................................ 160%*
*Percentage relates to frequency converters nominal current.

Number of programmable digital inputs .............................................................................................................. 5

Terminal number ....................................................................................................................... 18, 19, 27, 29, 33
Voltage level ...................................................................................................... 0 - 24 V DC (PNP positive logic)
Voltage level, logic 0 ............................................................................................................................. < 5 V DC
Voltage level, logic 1 ........................................................................................................................... > 10 V DC
Maximum voltage on input ...................................................................................................................... 28 V DC
Input resistance, R i (terminals 18, 19, 27, 29) ................................................................................. approx. 4 k

Input resistance, Ri (terminal 33) ..................................................................................................... approx. 2 k

All digital inputs are galvanically isolated from the supply voltage (PEL V) and other high-voltage terminals. See
section entitled Galvanic Isolation.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

23

Data sheet

Control card, digital inputs:

VLT 2800 Series

Control card, analog inputs:
Number of analog voltage inputs ................................................................................................................. 1 pcs.
Terminal number ................................................................................................................................................ 53
Voltage level .................................................................................................................... 0 - 10 V DC (scaleable)
Input resistance, R i ........................................................................................................................ approx. 10 k

Max. voltage .................................................................................................................................................. 20 V

Number of analog current inputs ................................................................................................................. 1 pcs.
Terminal number ................................................................................................................................................ 60
Current level .................................................................................................................... 0/4 - 20 mA (scaleable)
Input resistance, Ri ......................................................................................................................... approx. 300

Max. current ................................................................................................................................................ 30 mA

Resolution for analog inputs ......................................................................................................................... 10 bit
Accuracy of analog inputs .......................................................................................... Max. error 1% of full scale
Scan interval ......................................................................................................................................... 13.3 msec
The analog inputs are galvanically isolated from the supply voltage (PEL V) and other high-voltage terminals.
See section entitled Galvanic Isolation.
Control card, pulse inputs:
Number of programmable pulse inputs ............................................................................................................... 1
Terminal number ................................................................................................................................................ 33
Max. frequency at terminal 33 ............................................................................................. 67.6 kHz (Push-pull)
Max. frequency at terminal 33 .......................................................................................... 5 kHz (open collector)
Min. frequency at terminal 33 ....................................................................................................................... 4 Hz
Voltage level ...................................................................................................... 0 - 24 V DC (PNP positive logic)
Voltage level, logic 0 ............................................................................................................................. < 5 V DC
Voltage level, logic 1 ........................................................................................................................... > 10 V DC
Maximum voltage on input ...................................................................................................................... 28 V DC
Input resistance, Ri .......................................................................................................................... approx. 2 k

Scan interval ......................................................................................................................................... 13.3 msec

Resolution ..................................................................................................................................................... 10 bit
Accuracy (100 Hz- 1 kHz) terminal 33 .................................................................. Max. error: 0.5% of full scale
Accuracy (1 kHz - 67.6 kHz) terminal 33 .............................................................. Max. error: 0.1% of full scale
The pulse input (terminal 33) is galvanically isolated from the supply voltage (PEL V) and other high-voltage terminals. See section entitled Galvanic Isolation.
Control card, digital/frequency output:
Number of programmable digital/pulse outputs ........................................................................................... 1 pcs.
Terminal number ................................................................................................................................................ 46
Voltage level at digital/frequency output .......................................................................... 0 - 24 V DC (O.C PNP)
Max. output current at digital/frequency output ......................................................................................... 25 mA.
Max. load at digital/frequency output ............................................................................................................ 1 k

Max. capacity at frequency output .............................................................................................................. 10 nF

Minimum output frequency at frequency output .......................................................................................... 16 Hz
Maximum output frequency at frequency output ....................................................................................... 10 kHz
Accuracy on frequency output .............................................................................. Max. error: 0.2 % of full scale
Resolution on frequency output ................................................................................................................... 10 bit
The digital output is galvanically isolated from the supply voltage (PEL V) and other high-voltage terminals. See
section entitled Galvanic Isolation.

24

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Control card, analog output:
Number of programmable analog outputs ........................................................................................................... 1
Terminal number ................................................................................................................................................ 42
Current range at analog output .......................................................................................................... 0/4 - 20 mA
Max. load to common at analog output ...................................................................................................... 500

Accuracy on analog output ................................................................................... Max. error: 1.5 % of full scale

Resolution on analog output ........................................................................................................................ 10 bit
The analog output is galvanically isolated from the supply voltage (PEL V) and other high-voltage terminals.
See section entitled Galvanic Isolation.
Control card, 24 V DC supply:
Terminal number ................................................................................................................................................ 12
Max. load .................................................................................................................................................. 130 mA
The 24 V DC supply is galvanically isolated from the supply voltage (PEL V) , but has the same potential as the
analogue and digital inputs and outputs. See section entitled Galvanic Isolation.
Control card, 10 V DC supply:
Terminal number ................................................................................................................................................ 50
Output voltage ................................................................................................................................. 10.5 V 0.5 V
Max. load .................................................................................................................................................... 15 mA
The 10 V DC supply is galvanically isolated from the supply voltage (PEL V) and other high-voltage terminals.
See section entitled Galvanic Isolation.
Control card, RS 485 serial communication:
Terminal number .................................................................................................... 68 (TX+, RX+), 69 (TX-, RX-)
Terminal number 67 ...................................................................................................................................... + 5 V
Terminal number 70 .................................................................................. Common for terminals 67, 68 and 69
Full galvanic isolation. See section entitled Galvanic Isolation.
For CANopen/DeviceNet units, see VLT 2800 DeviceNet manual, MG.90.BX.YY .
Relay outputs:
Number of programmable relay outputs .............................................................................................................. 1
Terminal number, control card ......................................................................................... 1-3 (break), 1-2 (make)
Max. terminal load (AC) on 1-3, 1-2, control card ........................................................................ 240 V AC, 2 A
Min. terminal load on 1-3, 1-2, control card .................................................. 24 V DC 10 mA, 24 V AC 100 mA
The relay contact is separated from the rest of the circuit by strengthened isolation. See section entitled Galvanic Isolation.

Max. motor cable length, screened/armoured cable .................................................................................... 40 m

Max. motor cable length, unscreened/unarmoured cable ............................................................................ 75 m
Max. motor cable length, screened/armoured cable and motor coil .......................................................... 100 m
Max. motor cable length, unscreened/unarmoured cable and motor coil .................................................. 200 m
Max. motor cable length, screened/armoured cable and RFI/1B filter ........................................... 200 V, 100 m
Max. motor cable length, screened/armoured cable and RFI/1B filter ............................................. 400 V, 25 m
Max. motor cable length, screened/armoured cable and RFI 1B/LC filter ....................................... 400 V, 25 m
Max. cross section to motor, see next section.
Max. cross section to control wires, rigid wire ................................................ 1.5 mm2 /16 AWG (2 x 0.75 mm2 )
Max. cross section to control cables, flexible cable ..................................................................... 1 mm2 /18 AWG
Max. cross section to control cables, cable with enclosed core .............................................. 0.5 mm2 /20 AWG
When complying with EN 55011 1A and EN 55011 1B the motor cable must in certain instances be reduced. See EMC emission.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

25

Data sheet

Cable lengths and cross sections:

VLT 2800 Series

Control characteristics:
Frequency range .......................................................................................................... 0.2 - 132 Hz, 1 - 1000 Hz
Resolution of output frequency ...................................................................................... 0.013 Hz, 0.2 - 1000 Hz
Repeat accuracy of Precise start/stop(terminals 18, 19) ................................................................ 0.5 msec
System response time (terminals 18, 19, 27, 29, 33) ....................................................................... 26.6 msec
Speed control range (open loop) ............................................................................... 1:15 of synchronous speed
Speed control range (closed loop) .......................................................................... 1:120 of synchronous speed
Speed accuracy (open loop) .................................................................... 90 - 3600 rpm: Max. error of 23 rpm
Speed accuracy (closed loop) ................................................................ 30 - 3600 rpm: Max. error of 7.5 rpm
All control characteristics are based on a 4-pole asynchronous motor
Surroundings:
Enclosure ...................................................................................................................................................... IP 20
Enclosure with options ............................................................................................................................. NEMA 1
Vibration test ................................................................................................................................................. 0.7 g
Max. relative humidity ................................................................................................ 5% - 85% during operation


Ambient temperature ......................................................................... Max. 45 C (24-hour average max. 40 C)
Derating for high ambient temperature, see special conditions in the Design Guide

Min. ambient temperature during full-scale operation ................................................................................... 0 C

Min. ambient temperature at reduced performance .................................................................................. - 10 C

Temperature during storage/transport .......................................................................................... -25 - +65/70 C
Max. altitude above sea level ................................................................................................................... 1000 m
Derating for high air pressure, see special conditions in the Design Guide
EMC standards, Emission .......................................................................... EN 50081-2, EN 61800-3, EN 55011
EMC standards, Immunity .... EN 50082-1/2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN
61000-4-6, EN 61800-3
See section on special conditions in the Design Guide
Safeguards:

Electronic thermal motor protection against overload.

Temperature monitoring of the power module ensures that the frequency converter cuts out if the tempera
ture reaches 100 C. An overload temperature cannot be reset until the temperature of the power module is

below 70 C.
The frequency converter is protected against short-circuits on motor terminals U, V, W.
If a mains phase is missing, the frequency converter will cut out.
Monitoring of the intermediate circuit voltage ensures that the frequency converter cuts out if the intermediate circuit voltage is too low or too high.
The frequency converter is protected against earth fault on motor terminals U, V, W.

26

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Technical data, mains supply 1 x 220 - 240 V / 3 x 200-240V
According to . international standards
Output current

2803

2805

2807

2811

2815

2822

2840

I INV. [A]

2.2

3.2

4.2

6.0

6.8

9.6

16

(3 x 200-240V)
Output power (230 V)
Typical shaft output

IMAX (60s) [A]

SINV. [KVA]
PM,N [kW]

3.5
0.9
0.37

5.1
1.3
0.55

6.7
1.7
0.75

9.6
2.4
1.1

10.8
2.7
1.5

15.3
3.8
2.2

25.6
6.4
3.7

Typical shaft output

Max. cable cross
section, motor

PM,N [HP]
[mm 2 /AWG] 1 )

0.5
4/10

0.75
4/10

1.0
4/10

1.5
4/10

2.0
4/10

3.0
4/10

5.0
4/10

5.9
9.4

8.3
13.3

10.6
16.7

14.5
23.2

15.2
24.3

2.9
4.6
4/10

4.0
6.4
4/10

5.1
8.2
4/10

7.0
11.2
4/10

7.6
12.2
4/10

8.8
14.1
4/10

14.7
23.5
4/10

[A]
[%]
[W]

20/20
95
24

20/20
95
35

20/20
95
48

20/20
95
69

20/20
95
94

20/20
95
125

25/25
95
231

[kg]
type

2.0
IP 20

2.0
IP 20

2.0
IP 20

2.0
IP 20

2.0
IP 20

3,7
IP 20

6.0
IP 20

Input current
(1 x 220-240 V)
Input current
(3 x 200-240 V)
Max. cable cross
section, power
Max. pre-fuses
Efficiency3 )
Power loss at 100%
load
Weight
Enclosure4

Type

IL,MAX

IL,N [A]
(60s) [A]

IL,N [A]
IL,MAX (60s) [A]
[mm2 /AWG] 1 )
[A]/UL

2 )

Data sheet

1. American Wire Gauge. Max. cable cross section is the largest cable cross section that can be
attached to the terminals. Always observe national
and local regulations.
2. Type gG pre-fuses must be used. If you want to
maintain UL/cUL you must use pre-fuses of the
type Bussmann KTN-R 200 V, KTS-R 500 V or
Ferraz Shawmut, type ATMR (max. 30A). The
fuses must be placed for protection in a circuit that
is capable of supplying a maximum of 100,000
amps RMS (symmetrical), 500 V maximum.
3. Measured using a 25 m screened/armoured motor cable with a rated load and rated frequency.
4. IP20 is standard for VLT 2805-2875, whereas
NEMA 1 is an option.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

27

VLT 2800 Series

Technical data, mains supply 3 x 380 - 480 V
According to international stan-

Type

2805

2807

2811

2815

2822

2830

dards
Output current

I INV. [A]

1.7

2.1

3.0

3.7

5.2

7.0

(3 x 380-480V)

IMAX (60s) [A]

2.7

3.3

4.8

5.9

8.3

11.2

Output power (400 V)

Typical shaft output
Typical shaft output
Max. cable cross sec-

SINV. [KVA]

1.1

1.7

2.0

2.6

3.6

4.8

PM,N [kW]

0.55

0.75

1.1

1.5

2.2

3.0

PM,N [HP]

0.75

1.0

1.5

2.0

3.0

4.0

4/10

4/10

4/10

4/10

4/10

4/10

[mm2 /AWG]

1 )

tion, motor
Input current

IL,N [A]

1.6

1.9

2.6

3.2

4.7

6.1

(3 x 380-480 V)

IL,MAX(60s)[A]

2.6

3.0

4.2

5.1

7.5

9.8

Max. cable cross sec-

[mm2 /AWG]

4/10

4/10

4/10

4/10

4/10

4/10
20/20

1 )

tion, power
Max. pre-fuses

[A]/UL

2 )

[A]

20/20

20/20

20/20

20/20

20/20

[%]

96

96

96

96

96

96

Power loss at 100%

[W]

28

38

55

75

110

150

Efficiency3
load
Weight

[kg]

Enclosure4

type

According to international stan-

Type

2.1
IP 20
2840

2.1

2.1

2.1

IP 20

IP 20

IP 20

2855

2875

2880

3.7
IP 20
2881

3.7
IP 20
2882

dards
Output current

IINV. [A]

9.1

12

16

24

32.0

37.5

(3 x 380-480V)

IMAX (60s) [A]

14.5

19.2

25.6

38.4

51.2

60.0
26.0

Output power (400 V)

SINV. [KVA]

6.3

8.3

11.1

16.6

22.2

Typical shaft output

PM,N [kW]

4.0

5.5

7.5

11.0

15.0

18.5

Typical shaft output

PM,N [HP]

5.0

7.5

10.0

15.0

20.0

25.0

4/10

4/10

4/10

16/6

16/6

16/6

37.5

Max. cable cross sec-

[mm2 /AWG]

1 )

tion, motor
Input current

8.1

10.6

14.9

24.0

32.0

(3 x 380-480 V)

IL,MAX(60s)[A]

IL,N [A]

13.0

17.0

23.8

38.4

51.2

60

Max. cable cross sec-

[mm2 /AWG]

4/10

4/10

4/10

16/6

16/6

16/6

20/20

25/25

25/25

50/50

50/50

50/50

1 )

tion, power
Max. pre-fuses

[A]/UL

2 )

[A]

Efficiency3 )

[%]

96

96

96

97

97

97

Power loss at 100%

[W]

200

275

372

412

562

693

load
Weight
Enclosure4

[kg]

3.7

6.0

6.0

18.5

18.5

18.5

type

IP20

IP20

IP20

IP20/

IP20/

IP20/

NEMA 1

NEMA 1

NEMA 1

1. American Wire Gauge. Max. cable cross section is the largest cable cross section that can be
attached to the terminals. Always observe national
and local regulations.
2. Type gG pre-fuses must be used. If you want to
maintain UL/cUL you must use pre-fuses of the
type Bussmann KTN-R 200 V, KTS-R 500 V or
Ferraz Shawmut, type ATMR (max. 30A). The
fuses must be placed for protection in a circuit that
is capable of supplying a maximum of 100,000
amps RMS (symmetrical), 500 V maximum.
28

3. Measured using a 25 m screened/armoured motor cable with a rated load and rated frequency.
4. IP20 is standard for VLT 2805-2875, whereas
NEMA 1 is an option.

MD.28.A5.02 - VLT is a registered Danfoss trade mark

VLT 2800 Series

Accessories for the VLT 2800

Type
Motor coil
RFI 1B filter
RFI 1B/LC filter 4 A
RFI 1B/LC filter 9.1 A
NEMA 1 terminal cover
NEMA 1 terminal cover
NEMA 1 terminal cover
LCP2 control unit
Cable for LCP2 control unit
DeviceNet cable
LCP2 remote-mounting kit
LOP (Local Operation Pad)
VLT Software Dialog

Description
The motor coil module can be used for VLT 2803-2875
The RFI 1B filter module can be used for VLT 2803-2875
The RFI 1B/LC filter 4 A can be used for VLT 2803-2805
200-240 V and VLT 2805-2815 380-400 V
RFI 1B/LC filter 9.1 A can be used for VLT 2807-2815
200-240 V and VLT 2822-2840 380-400 V
VLT 2803-2815 200-240 V, VLT 2805-2815 380-480 V
VLT 2822 200-240 V, VLT 2822-2840 380-480 V
VLT 2840 200-240 V, VLT 2855-2875 380-480 V
LCP2 for programming the frequency converter
Cable from LCP2 to frequency converter
Cable for DeviceNet connection
Kit for remote-mounting of LCP2 (incl. 3 m cable,
excl. LCP2)
LOP can be used for setting the reference
and start/stop via the control terminals.
CD-ROM version*

Ordering no.
195N3110
195N3103
195N3100
195N3101
195N1900
195N1901
195N1902
175N0131
175Z0929
195N3113
175Z0850
175N0128
175Z0953

Data sheet

* Incl. the modules Basis, Logging, Template,

Guided Tour in 6 languages (Danish, English, German, Italian, Spanish and French).

MD.28.A5.02 - VLT is a registered Danfoss trade mark

29

VLT 2800 Series

Available literature
Supplied with the unit
Below is a list of the literature available for VLT
2800. It must be noted that there may be deviations
from one country to the next.
Supplied with the unit:
Operating instructions ..................................................................................................................... MG.28.AX.YY
Quick setup ..................................................................................... MG.28.BX.YY, MG.28.CX.YY , MG.28.FX.YY
Parameter list .................................................................................................................................. MG.28.DX.YY
Various literature for VLT 2800:
Design Guide .................................................................................................................................. MG.28.EX.YY
Data sheet ....................................................................................................................................... MD.28.AX.YY
Instructions for VLT 2800:
LCP remote-mounting kit ................................................................................................................... MI.56.AX.51
Filter instruction .................................................................................................................................. MI.28.B1.02
Communication with VLT 2800:
Profibus manual .............................................................................................................................. MG.90.AX.YY
VLT 2800 DeviceNet manual .......................................................................................................... MG.90.BX.YY
X = version number
YY = language version

30

MD.28.A5.02 - VLT is a registered Danfoss trade mark