12/18/2019 Service Information System

Testing and Adjusting

14M3 and 14 Motor Grader Machine Systems
Media Number -M0070306-03 Date Updated -02/10/2019

i06679654

Cylinder Cycle Time - Check

SMCS - 7562-535-VF

Table 1
Required Tools
A Stopwatch or Timer 1

Note: Before you perform this check, refer to Testing and Adjusting, "Machine Preparation".

Use Table 2 to determine the correct cylinder cycle times. Choose the column that has the cycle times for
your Motor Grader. Record the actual cycle times in the column that is on the right side of the table. The
cycle times that are shown in Table 2 are in seconds.

For most cylinders, a test cycle is the full range of movement. For the following cylinders, a test cycle is
movement through a 305 mm (12.0 inch) distance: blade lift cylinders and ripper cylinder. For the circle, a
test cycle is 1/4 of one full rotation.

All the checks of the implement cycle times must be performed at high idle. The hydraulic oil must be at
normal operating temperature. Ensure that the cylinder bears no additional loads. The following causes
will create additional loads: interference from other machine components, contact with foreign objects and
contact with the ground.

Table 2
Implement Cycle Times for Motor Graders
Implement
Cycle Actual
Implement Action Times Implement
14M Series Cycle Times
3

Rod In(1)
3.0 ± 1.0
Blade Lift Rod
3.0 ± 1.0
Out(1)

Rod In(2)
5.5 ± 2.0
Centershift Rod
6.5 ± 2.0
Out(2)

Rod In(2)
2.0 ± 0.5
Wheel Lean Rod
2.5 ± 1.0
Out(2)

Rod In(2)
6.0 ± 2.0
Blade Tip Rod
5.5 ± 1.5
Out(2)
Sideshift Rod In(2) 16.0 ± 4.0
https://sis.cat.com/sisweb/servlet/cat.cis.sis.PController.CSSISTechDocServlet 1/3
12/18/2019 Service Information System

Rod 16.0 ± 4.0

Out(2)

Rod In(1)
Ripper (If Equipped) B9J1-Up, ; B9H1-Up, ; R9J1-215, ; 4.5 ± 1.5
Rod
R9H1-201 5.5 ± 1.5
Out(1)

Rod In(1)
Ripper (If Equipped) R9J216-Up, ; R9H202-Up, ; 3.5 ± 1.0
Rod
N9Y1-Up, ; E9Y1-Up, ; N9A1-Up, ; E9W1-Up 4.0 ± 1.5
Out(1)

Left(2) (3)
4.0 ± 1.0
Articulation Right(2)
(3)
4.0 ± 1.0

1/4
Blade Circle 13.0 ± 4.0
Rotation
(1) Cycle times are for a “running distance” of 305 mm (12 inch).
(2) Cycle time is through full travel.
(3) When you check the cycle times for these cylinders, operate the machine at high idle and in the FIRST SPEED position. The
differential must be unlocked.

Procedure To Check Blade Lift Cycle Times and Ripper (If

Equipped) Cycle Times
Table 3
Required Tools
A Stopwatch or Timer 1
1U-9366 Automatic Tape Measure 1

View Image

https://sis.cat.com/sisweb/servlet/cat.cis.sis.PController.CSSISTechDocServlet 2/3
12/18/2019 Service Information System

Illustration 1 g01373871
(1) Cylinder rod
(2) Marks
(3) Tape measure
(A) Running distance

1. Raise the implement that needs to be checked to the maximum height.

2. Place a mark on the rod. Place the mark just below the cylinder head. Use ink to create all marks. Do
not create marks by scratching or by scoring.

3. Use the stopwatch to determine the time that is required to lower the cylinder by 305 mm
(12.0 inch). Use the tape measure to determine 305 mm (12.0 inch) of movement. Use the mark as a
reference.

4. Position the implement just above the ground.

5. Place two marks on the rod. Place the marks 305 mm (12.0 inch) away from each other.

6. Use the stopwatch to determine the time that is required to raise the cylinder by 305 mm (12.0 inch).
Use the marks for reference.

Copyright 1993 - 2019 Caterpillar Inc. Wed Dec 18 2019 06:40:37 GMT+0800 (Singapore Standard Time)
All Rights Reserved.
Private Network For SIS Licensees.

https://sis.cat.com/sisweb/servlet/cat.cis.sis.PController.CSSISTechDocServlet 3/3