Hwra Guideline
Hwra Guideline
Notification
The 10th September, 2021
No. HWRA/485/Notification/2021.— In exercise of the powers conferred under Sub-section (3) of Section
12 of "The Haryana Water Resources (Conservation, Regulation And Management) Authority Act", 2020, (the Act)
and in supersession of the Notification No.2/62/2020-1IW (hereinafter earlier notification) dated 23.12.2020, the
procedure, forms, terms & conditions, fee and charges etc., for seeking permissions from “The Haryana Water
Resources Authority” (Short HWRA) under Section 16 of the Act is hereby provided as under.
The permissions/NOCs granted by or application submitted to the Authority, under the earlier notification shall
deemed to have been granted or submitted to the Authority under this notification.
1) The intended user i.e. industry, mining or infrastructure, as the case may be, may apply, online from the
portal of the authority, for seeking permissions to use water.
2) An online application shall be made to the Authority for seeking permission/No objection Certificate to
use water, for industrial use, along with such documents and information specified in the Schedule-I.
3) An online application shall be made to the Authority for seeking permission/No objection Certificate to
use water, for mining use, in along with such documents and information specified in the Schedule-II.
4) An online application shall be made to the Authority for seeking permission/No objection Certificate to
use water, for infrastructure use, along with such documents and information specified in the Schedule-III.
5) The person or entity, as the case may be, shall pay a processing fee, as provided under Schedule-IV,
along with the application for seeking permissions/No objection Certificate.
6) All the permissions to be given, shall be subject to such terms and conditions as mentioned in the
respective Schedule and as the Authority may deem fit.
7) All the permissions/No objection Certificate shall be given under the seal of the Authority.
8) All the permissions/No objection Certificate shall be valid for one year :
Provided that the applicant has to comply with the further terms and conditions as may be imposed by
the Authority and no person can deny to comply with the terms and conditions merely because he has sought
the permissions/No objection Certificate under the earlier notification.
9) The applicant, on grant of permission/No objection Certificate, shall be liable to pay Ground water
abstraction/ restoration charges as per Appendix 5.0.
Exemptions from seeking No Objection Certificate :
Following categories of users/persons shall be exempted from seeking No Objection Certificate for ground
water extraction :
(i) Individual domestic consumers in both rural and urban areas for drinking water and domestic
uses where public water supplies do not exist.
(ii) Rural drinking water supply schemes.
(iii) Armed Forces Establishments and Central Armed Police Forces establishments in both rural and
urban areas.
(iv) Agricultural activities.
(v) Micro and small Enterprises drawing ground water less than 10 cum/day. However, such MSME
shall get its self registered itself with the Authority.
SCHEDULE-I
Industrial Use :-
In Over-exploited assessment units, NOC shall not be granted for ground water abstraction to any new industry
except those falling in the category of Micro, Small and Medium Enterprises (MSME). However, NOC for drinking/
domestic use for work force, use by these new industries shall be permitted. NOC shall not be granted to new
packaged water industries or water intensive industries in Overexploited areas, even if they belong to MSME
category.
In case of Expansion of existing industries, in over-exploited assessment units, involving increase in quantum of
ground water abstraction, only for production of ethanol, in public interest, shall be permitted with additional terms &
conditions mentioned at 1A
NOC for ground water extraction by industries shall be granted subject to the following specific conditions :
(i) NOC shall be granted only in such cases where local government water supply agencies are not able to
supply the desired quantity of water.
(ii) All industries shall be required to adopt latest water efficient technologies so as to reduce dependence
on ground water resources.
(iii) All industries abstracting ground water between 100-500 m3/d shall be required to undertake self annual
water audit as per the format provided by HWRA along with the affidavit and submit audit reports
within three months of completion of the same to HWRA. Industries abstracting ground water in excess
of 500 m3/d shall be required to undertake annual water audit through Confederation of Indian
Industries (CII)/ Federation Indian Chamber of Commerce and Industry (FICCI)/ National Productivity
Council (NPC) certified auditors and submit audit reports within three months of completion of the
same to HWRA. All industries shall be required to reduce their ground water use by at least 20% over
the next three years through appropriate means.
(iv) Construction of observation well(s) (piezometer)(s) along with automatic water level recorder, within
6 months from the date of issuance of NOC, within the premises and installation of appropriate water
level monitoring mechanism, shall be mandatory for industries drawing/ proposing to draw more than
500 m3/day of ground water and. Monitoring of water level shall be done by the project proponent. The
piezometer (observation well) shall be constructed at a minimum distance of 15 m. from the bore
well/production well. Depth and aquifer zone tapped in the piezometer shall be the same as that of the
pumping well/ wells. Detailed guidelines for design and construction of piezometers are given in
Annexure II. Monthly water level data shall be submitted to the HWRA through the web portal.
(v) The proponent shall be required to adopt roof top rain water harvesting/ recharge in the project
premises. Industries which are likely to pollute ground water (chemical, pharmaceutical, dyes,
pigments, paints, textiles, tannery, pesticides/ insecticides, fertilizers, slaughter house, explosives etc.)
shall store the harvested rain water in surface storage tanks for use in the industry and accordingly
reduce their abstraction of ground water requirement.
(vi) Injection of treated/ untreated waste water into aquifer system is strictly prohibited.
(vii) Industries which are likely to cause ground water pollution e.g. Tanning, Slaughter Houses, Dye,
Chemical/ Petrochemical, Coal washeries, other hazardous units etc. (as per CPCB list) need to
undertake necessary well head protection measures to ensure prevention of ground water pollution
(Annexure III).
(viii) All industries drawing ground water in safe, semi-critical and critical assessment units shall be required
to pay ground water abstraction charges as applicable as per Tables 5.2 A and 5.3 A.
(ix) All existing industries drawing ground water in over-exploited assessment units shall be liable to pay
ground water restoration charges as applicable as per Tables 5.2 B and 5.3 B.
1A) Additional terms & conditions:-
The industry shall recharge groundwater through rain water harvesting by double the amount of water
consumed by them. The units shall adopt nearby Government Schools/ Colleges/Institutions, Village
Ponds etc. for rain water harvesting.
The industry shall take measures to reduce their water consumption by 30% in 3 years time.
The industry shall pay 1.5 times the tariff compared to the normal tariff being charged in such areas for
the additional quantities of water being abstracted.
The industry shall ensure for "Zero Liquid Discharge".
Government water supply agencies and Government infrastructure projects shall pay Ground water abstraction
Charges @ Rs. 0.50 per m3.
II. Packaged Drinking Water units
Rates of ground water abstraction charges for packaged drinking water units in safe, semi-critical and critical
assessment units are given in Table 5.2 A and those for ground water restoration charges in over-exploited assessment
units are given in Table 5.2 B.
Table 5.2 A: Rates of ground water abstraction charges for packaged drinking water units (Rs. per m 3)
S. No. Category Quantum of ground water withdrawal
of area Up to 50m3/ 51 to <200 200 to <1000 1000 to 5000
day m3/day m3/day <5000 m3/day
m3/day and above
Ground
water use
1. Safe 1.00 3.00 5.00 8.00 10.00
2. Semi-critical 2.00 5.00 10.00 15.00 20.00
3. Critical 4.00 10.00 20.00 40.00 60.00
Table 5.2 B: Rates of ground water restoration charges for packaged drinking water units (Rs. per m 3)
Table 5.3 B: Rates of ground water restoration charges for other industries & infrastructure projects
(Rs. per m3)
Chairperson
Haryana Water Resources Authority
Annexure I
Estimation of Water Requirements for drinking and domestic use
(Source: National Building Code 2016, BIS)
(a) Residential Buildings :
Accommodations Population
1 Bedroom dwelling unit 4
2 Bedroom dwelling unit 5
3 Bedroom dwelling unit 6
4 Bedroom dwelling unit and above 7
Notes:
1) The above figures consider a domestic household including support personnel, wherever applicable.
2) For plotted development, the population may be arrived at after due consideration of the expected
number and type of domestic household units.
3) Dwelling unit under EWS category shall have population requirement of 4 and studio apartment shall
have population requirement of 2.
As a general rule the following rates per capita per day may be considered for domestic and non-domestic needs :
(a) For communities with populations up to 20,000 :
1) Water supply through stand post: 40 lphd (Min)
2) Water supply through house service: connection 70 to 100 lphd
(b) For communities with : 100 to 135 lphd
population 20,000 to 100,00 together with
full flushing system
(c) For communities with population : 150 to 200 lphd
above 100,000 together with
full flushing system
Note—The value of water supply given as 150 to 200 litre per head per day may be reduced to 135 litre per head per
day for houses for Medium Income Group (MIG) and Low Income Groups (LIG) and Economically Weaker Section
of Society (EWS), depending upon prevailing conditions and availability of water.
Out of the 150 to 200 litre per head per day, 45 litre per head per day may be taken for flushing requirements and the
remaining quantity for other domestic purposes.
B. Water Requirements for Buildings Other than Residences
Sl. Type of Building Domestic litres Flushing Total Consumption
No. per head/ day Litres per head/ Litres per head/ day
day
1. Factories including canteen where 30 15 45
bath rooms are required to be
provided
2. Factories including canteen where no 20 10 30
bath rooms are required to be
provided
3. Hospital (excluding laundry and
kitchen):
a) Number of beds not exceeding
100
230 110 340
b) Number of beds exceeding 100
300 150 450
c) Out Patient Department (OPD)
10 5 15
90 45 135
b) Visitors 5 10 15
15. Traffic Terminal stations
(a) Airports 40 30 70
(b) Railway stations (Junction)
with bathing facility 70
40 30
(c) Railway stations (Junction)
without bathing facility 45
30 15
(d) Railway stations (Intermediate)
with bathing facility 45
25 20
(e) Railway stations (Intermediate)
without bathing facility 25
15 10
(f) Interstate bus terminals 25 20 45
(g) Intrastate Bus Terminals/
10 5 15
Metro Stations
Notes:
1. For calculating water demand for visitors, consumption of 15 litre per head per day may be taken.
2. The water demand includes requirement of patients, attendants, visitors and staff. Additional water
demand for kitchen, laundry and clinical water shall be computed as per actual requirements.
3. The number of persons shall be determined by average number of passengers handled by stations, with
due considerations given to the staff and vendors who are using these facilities.
4. Consideration should be given for seasonal average peak requirements.
5. The hospitals may be categorized as Category A (25 to 50 beds), Category B(51 to 100 beds), Category C
(101 to 300 beds), Category D (301 to 500) and Category E (501 to 750 beds).
Annexure II
Guidelines for construction of Piezometers and monitoring of Ground Water Levels and Quality
Piezometer is a borewell/tubewell used only for measuring the water level by lowering a tape/sounder or automatic /
digital water level measuring equipment. It is also used to take water sample for water quality testing whenever
needed. General guidelines for installation of piezometers are as follows :
• The piezometer is to be installed/constructed at the minimum distance of 50 m. from the pumping
well through which ground water is being withdrawn. The diameter of the piezometer should be about
“4 to 6”.
• The depth of the piezometer should be the same as that of the pumping well from which ground water
is being abstracted. If, more than one pumping wells are constructed tapping aquifers at different
depths, more than one piezometers shall be required to be constructed tapping different aquifers as in
the pumping wells.
• The measurement of water level in piezometer should be taken, only after the pumping from the
surrounding tubewells has been stopped for about four to six hours.
• The ground water quality has to be monitored once in a year during pre-monsoon (April/ May) period
by industries and mines drawing ground water. Samples of ground water should be analyzed from
NABL accredited laboratory.
• A permanent display board should be installed at Piezometer/ Tubewell site for providing the location,
piezometer/ tubewell number, depth and zone tapped of piezometer/tubewell for standard referencing
and identification.
• Any other site specific requirement regarding safety and access for measurement may be taken care off.
Annexure III
Measures to be adopted to ensure prevention from pollution in the plant premises of polluting industries/
projects
It has been observed that ground water in and around polluting industries like Tannery, Slaughter Houses, Dye,
Chemical, Coal washery, other hazardous units, etc., is polluted. In order to prevent further deterioration of ground
water quality, it is essential to take all necessary measures for well head protection. All industries/ projects falling
under this category are hereby directed to follow the under mentioned procedure both for existing and new category.
1. No tube well/ bore well / dug well should be constructed in the vicinity of the processing unit. Tube well/ bore
well should be constructed at the place which is hygienically maintained.
2. Only Mild Steel pipe should be used for assembly/ casing and PVC (Poly Vinyl Chloride) or similar pipes
should not be used. The tube well/ bore well having PVC or similar pipes should be abandoned and filled
back.
3. Around the tube well/ bore well, RCC (Reinforced Concrete Cement) grouting of 3 meters (length) x 3 meters
(width) x 2 meters (depth) must be provided. The pipe of the tube well/ bore well must be raised 1 meter above
ground level (1 magl). The tube well/ bore well must be surrounded by RCC wall of 0.5 meter height and
1.5 meter depth to prevent any surface contamination to enter the constructed tube well/ bore well.
Plan/Sectional diagram is enclosed for reference.
3. The tube well/ bore well must be fitted with NRV (Non Return Valve) in order to ensure that the constructed
tube well/ bore well is exclusively used for abstraction of ground water only.
4. At no point of time there should be any injection of any water or fluid into the constructed tube well/
bore well/ Piezometer.
5. The industries/ projects under this category should not implement any recharge measures within the plant
premises.
6. Any tube well/ bore well located/ constructed in the vicinity of STP (Sewage Treatment Plant) or
ETP (Effluent Treatment Plant) should be abandoned and filled back.
7. The piezometer to be constructed for monitoring purpose should follow the same procedure as that for
tube well/ bore well for such industries/ projects.
Plan/ Sectional diagram showing well head protection
Plan/ Sectional diagram showing well head protection
Annexure-IV
Outline of hydro-geological Report for obtaining NOC for industries
1. Brief about the proposed project giving location details, coordinates, google/ toposheet maps, etc. demarcating
the project area.
2. Ground water situation in and around the project area including water level and quality data and maps along
with quality issues, if any. In case of mines, ground water conditions in both core and buffer zone should be
described.
3. Details of the tubewells/ borewells proposed to be constructed. This includes the drilling depth, diameter,
tentative lithological log, details of pump to be lowered, H.P. of pump, tentative discharge of tubewells/
borewells, etc. Locations to be marked on the site plan/ map. Location of proposed piezometers.
4. Approved Mine plan in case of mines and detailed dewatering plan in case of mine/ infrastructure dewatering
projects.
5. Proposed usage of pumped water in case of mining/ infrastructure dewatering projects.
6. Comprehensive assessment of the impact on the ground water regime in and around the project area
highlighting the risks and proposed management strategies proposed to overcome any significant
environmental issues.
7. Proposed measures for disposal of waste water by industries drawing saline water.
8. Measures to be adopted for water conservation which include recycling, reuse, treatment, etc. This includes the
water balance chart being adopted by the firm along with details of water conservation methods to be adopted.
- Brief write up along with capacity and flow chart of Sewage Treatment Plants / Effluent Treatment
Plants / Combined Effluent Treatment Plants existing/ proposed within the project.
- Details of water conservation measures to be adopted to reduce/ save the ground water.
- Total water balance chart showing the usage of water for various processes.
9. Any other details pertaining to the project.
Annexure V
Format of the Report on ground water conditions (for mining projects)
Introduction
Project description
Background
Objectives and scope
Regional setting
Location
Land-use
Climate
Topography and drainage
Geology –Regional and Local
General Hydrogeology (aquifer types, aquifer depth, zone tapped etc.)
Groundwater condition (In core and buffer zones)
Spatial and temporal variations in water levels Groundwater quality (Shallow and deep aquifer)
Impact of groundwater extraction on local groundwater
Hydrograph of water level/piezometer in monitoring wells
Trend analysis of historical water levels Flow net analysis (groundwater flow direction)
Year wise/ bench wise mine dewatering computation as per approved mine plan
Conclusions
Annexure VI
Indicative list of Infrastructure projects
Residential townships including commercial buildings
Office building
School
College
University
Special Economic Zone
Metro Station
Railway Station
Bus Depot
Airport
Seaport
Highway infrastructure
Fire station
Warehouse
Business Plaza
Malls & Multiplex
Hospitals
Nursing Homes
Resort
Hotel/ Restaurant / Food Plaza
Holiday home / Guest house/ Hostels
Banquet Hall / Marriage Gardens
IT Complex
Logistics & Cargo
Clubs
Trade Centre/ Agri Markets
STAGE OF GROUND WATER DEVELOPMENT AND CATEGORIZATION OF THE BLOCKS AS ON 31-
3- 2017
Sr. No. District Over-exploited Critical Semi-critical Safe
1. Ambala Barara, Naraingarh, Saha Shahzadpur Ambala-I Ambala-II
2. Bhiwani Behal, Kairu, Loharu, Tosham - Bhiwani Bhiwani Khera,
Siwani
3. Charkhi Dadri Badhra, Jhoju - Ch. Dadri Baund
4. Faridabad Ballabhgarh, Faridabad - - -
5. Fatehabad Fatehabad, Ratia, Tohana, Bhuna - -
Jakhal, Bhattu Kalan
6. Gurugram Farukhnagar,
Pataudi, Sohna, Gurugram
7. Hissar Adampur, Agroha, Narnaund Barwala Bass, Hisar-I, Hansi
Hisar-II, Uklana
8. Jhajjar Jhajjar, Matanhail,
Salhawas, Beri,
Bhadurgarh
9. Jind Alewa, Uchana, Ujhana, - Pillukhera Julana, Narwana
Safidon, Jind
10. Kaithal Siwan, Gulha, Kaithal, Kalyat, - - -
Pundri, Rajaund, Dhand
11. Karnal Assandh, Gharaunda, - Indri -
Karnal, Nilokheri,
Nissing at Chirao
12. Kurukshetra Ismailabad, Babain, Ladwa, - - -
Pehowa, Shahbad, Thanesar,
Pipli
13. M.garh Kanina, Mahendragarh - Nangal Narnaul, Nizampur
Chaudhary,
Satnali, Simha,
Ateli Nangal
14. Mewat Punhana, Tauru - Nuh, Ferozepur Nagina
Jhirka
15. Palwal Hassanpur, Hathin, Hodel, - - -
Palwal
16. Panchkula - - Raipur Rani Pinjore, Barwala
17. Panipat Bapoli, Israna, Madlauda, - - -
Panipat, Samalkha
18. Rewari Khol, Rewari, Nahar - Dahina, Jatusana Bawal
19. Rohtak Lakhan Majra,
Meham, Kalanaur,
Sampla, Rohtak
20. Sirsa Ellenabad, Rania, Sirsa, - - -
Nathusari Chopta, Baraguda,
Odhan, Dabwali
21. Sonepat Ganaur, Sonepat, Rai - Mundlana Gohana, Kathura,
Kharkhoda
22. Yamunanagar Chachrauli, Jagadhri, - Sadaura, Bilaspur -
Mustafabad, Khizrabad, Radour
State Total 78 3 21 26
*Morni block of district Panchkula not assessed due to complete hilly area.