Designated client product

This product will be discontinued its production in the near term.

And it is provided for customers currently in use only, with a time limit.
It can not be available for your new project. Please select other new or
existing products.
For more information, please contact our sales office in your region.

New Japan Radio Co.,Ltd.

www.njr.com
 NJM5534

HIGH PERFORMANCE LOW-NOISE OPERATIONAL AMPLIFIER

■ GENERAL DESCRIPTION ■ PACKAGE OUTLINE

The NJM5534 is a high performance low noise operational amplifier.
This amplifier features popular pin-out, superior noise performance,
and high output drive capability. And also, features guaranteed noise
performance with substantially higher gain-bandwidth product, power
bandwidth, and slew rate which far exceeds that of the NJM741 type
amplifiers.
The specially designed low noise input transistors allow the NJM5534D NJM5534M
(DIP8) (DMP8)
NJM5534 to be used in very low noise signal processing applications
such as audio pre-amplifiers and servo error amplifiers.
The NJM5534 is internally compensated for a gain of three or higher.
Externally compensation for optimizing specific performance can be
obtained by use of an external compensation capacitor between
COMPENSATION(5PIN) and BALANCE/COMPENSATION(8PIN).
If very low noise characteristic is of prime importance, it is
recommended D-Rank type products(NJM5534DD/MD). These
have specified maximum limits for equivalent input noise voltage.

■ FEATURES
● Operating Voltage ±3V~±22V
● Single Circuit
● With BALANCE Terminal
● Low Input Noise Voltage 3.3nV/√Hz typ.@1kHz
● Power Bandwidth 200kHz typ.
● Slew Rate 13V/µs typ.
● Package Outline DIP8, DMP8
● Bipolar Technology

■ PIN CONFIGURATION
(Top view) PIN FUNCTION
1 8 1.BALANCE
2.–INPUT
2 7 3.+INPUT
4.V-
3 6
5.COMPENSATION
4 5 6.OUTPUT
7.V+
DIP8, DMP8 Package 8.BALANCE/COMPENSATION

■ EQUIVALENT CIRCUIT

Ver.2011-02-22 -1-
NJM5534
■ ABSOLUTE MAXIMUM RATINGS (Ta=25˚C)
PARAMETER SYMBOL RATING UNIT
+ -
Supply Voltage V /V ±22 V
Differential Input Voltage VID ±0.5 V
Common Mode Input Voltage VIC V+/V- V
DIP8: 500
Power Dissipation PD mW
DMP8: 300
Operating Temperature Range Topr -20~+75 °C
Storage Temperature Range Tstg -40~+125 °C

■ RECOMMENDED OPERATING VOLTAGE (Ta=25˚C)

PARAMETER SYMBOL RATING UNIT
+ -
Supply Voltage V /V ±3~±22 V

■ ELECTRICAL CHARACTERISTICS (Ta=25˚C,V+/V-=±15V, unless otherwise noted.)

PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
Input Offset Voltage VIO RS≤10kΩ - 0.5 4 mV
Input Offset Current IIO - 20 300 nA
Input Bias Current IB - 500 1500 nA
Input Resistance RIN 30 100 - kΩ
Large Signal Voltage Gain AV RL≥2kΩ, VO=±10V 88 100 - dB
Maximum Output Voltage VOM RL≥600Ω ±12 ±13 - V
Common Mode Input Voltage Range VICM ±12 ±13 - V
Common Mode Rejection Ratio CMR RS≤10kΩ 70 100 - dB
Supply Voltage Rejection Ratio SVR RS≤10kΩ 80 100 - dB
Supply Current ICC RL=∞ - 4 8 mA
Trainsient Response Rise Time tR VIN=50mV, RL=600Ω, CL=100pF, Cc=22pF - 35 - ns
Overshoot VIN=50mV, RL=600Ω, CL=100pF, Cc=22pF - 17 - %
Slew Rate SR Cc=0 - 13 - V/µs
Gain Bandwidth Product GB Cc=22pF, CL=100pF - 10 - MHz
Power Bandwidth WPG Vo=20VPP, Cc=0 - 200 - kHz
Equivalent Input Noise Voltage VNI f=20Hz~20kHz - 1 - µVrms
Equivalent Input Noise Current INI f=20Hz~20kHz - 25 - pArms
fO=30Hz - 5.5 - nV/√Hz
Equivalent Input Noise Voltage en
fO=1kHz - 3.3 - nV/√Hz
fO=30Hz - 1.5 - pA/√Hz
Equivalent Input Noise Current in
fO=1kHz - 0.4 - pA/√Hz
Broadband Noise Figure NF f=10Hz~20kHz, RS=5kΩ - 0.9 - dB

■ ELECTRICAL CHARACTERISTICS (D-rank type(Note1), V+/V-=±15V, Ta=25°C, unless otherwise noted.)

PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT
Equivalent Input Noise Voltage VNI RIAA, RS=2.2kΩ - - 1.4 µVrms
(Note1)D-rank type is a Equivalent Input Noise Voltage selected product.

-2- Ver.2011-02-22
 NJM5534
■ TYPICAL CHARACTERISTICS

Gain/Phase vs. Frequency Maximum Output Voltage vs. Load Resistance

Ta=25ºC Ta=25ºC
50 25
Gain 20
40 V+/V-=±22V

Maximum Output Voltage [V]

15
Phase
30 0 10 +Vom V+/V-=±15V
Voltage Gain [dB]

Phase [deg]
5
20 -40
0
10 -80
-5

0 -120 -10 -Vom V+/V-=±15V

-15
V+/V-=±22V
-10 -160
-20
-20 -200 -25
10k 100k 1M 10M 100M 10 100 1k 10k
Frequency [Hz] Load Resistance [Ω]

Maximum Output Voltage Swing vs. Frequency Maximum Output Voltage Swing vs. Frequency
V+/V-=±15V, Ta=25ºC V+/V-=±15V, Ta=25ºC
35 35
Maximum Output Voltage Swing

Maximum Output Voltage Swing

30 30
Cc=0pF
25 25
Cc=50pF
20 20 Cc=20pF
[Vpp]

[Vpp]

15 15

10 10

5 5

0 0
10k 100k 1M 10M 10k 100k 1M
Frequency [Hz] Frequency [Hz]

Voltage Noise vs. Source Resistance THD vs. Output Voltage

V+/V-=±15V, Ta=25ºC V+/V-=±15V, RL=10kΩ, Gv=20dB, Ta=25ºC
100 0.01
Weighting
Equivalent Input Noise Voltage

Total Harmonic Distortion [%]

Rs 100 10k
f=20kHz
10
[µVrms]

Flat
0.001 f=20Hz
100kHz LPF
1 f=1kHz
JIS A

0.1 0.0001
10 100 1k 10k 1 10
Source Resistance [Ω] Output Voltage [Vrms]

Ver.2011-02-22 -3-
NJM5534
■ TYPICAL CHARACTERISTICS

Supply Current vs. Temperature Input Offset Voltage vs. Temperature

V+/V-=±15V V+/V-=±15V
9 2.5

8 2

Input Offset Voltage [mV]

7
1.5
Supply Current [mV]

6
1
5
0.5
4
0
3
-0.5
2

1 -1

0 -1.5
-50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125
Ambient Temperature [ºC] Ambient Temperature [ºC]

Input Bias Current vs. Temperature Maximum Output Voltage vs. Temperature
V+/V-=±15V V+/V-=±15V, RL=600Ω
900 15

800 +Vom
10
Maximum Output Voltage [V]

700
Input Bias Current [nA]

600 5

500
0
400

300 -5

200
-10
-Vom
100

0 -15
-50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125
Ambient Temperature [ºC] Ambient Temperature [ºC]

Slew Rate vs. Compensation Capacitance

Ta=25ºC
16

14

12
Slew Rate [V/µs]

10

0
0 10 20 30 40 50 60 70 80 90 100
Compensation Capacitance Cc [pF]

-4- Ver.2011-02-22
 NJM5534
■ TEST CIRCUIT
+15V -15V
Noise Voltage (RIAA) measurement circuit

100µ 100µ 40dB Amp

Rs
30kHz LPF
3.3µ 2.2k
0.47µ 2.2µ
Vout

56k
30k 330k 220k

0.0024µ 0.0082µ
47µ

610

■ ADJUSTMENT METHOD
Fig.1-1, Fig.1-2 shows the input offset voltage adjustment circuit, and frequency compensation circuit.
Without these features, the adjustment pins are open.

Fig.1-1 Input Offset Voltage Adjustment Fig.1-2 Frequency Compensation

+
V

22k

Cc
100k
1 8
2 2
8 5
6 6
3 3

■ NOTICE
When used in voltage follower circuit, put a current limit resistor into non-inverting input terminal in order to avoid inside
input diode destruction when the power supply is turned on. ( ref.Fig.2 )

1k OUTPUT
INPUT

Fig.2

[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.

Ver.2011-02-22 -5-