Aluminium Electrolytic Capacitor

2015-2장 2015.1.
20 03:35 PM 페이지31 태산아이인쇄그룹(국) 2261-2488 2400DPI 175LPI
2
CONDUCTIVE
POLYMER ALUMINUM ELECTROLYTIC CAPACITORS
2015-2장 2015.1.20 03:35 PM 페이지32 태산아이인쇄그룹(국) 2261-2488 2400DPI 175LPI
CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS
Hi-CAP (Conductive Polymer Aluminum Electrolytic Capacitor)
Hi-CAP is an electrolytic capacitor that uses a highly electric conductive polymer as it’s electrolyte.
Hi-CAP has excellent temperature and load life characteristics due to adoption of stable polymer in high temperature.
Compared to other electrolytic capacitors, the Hi-CAP is a low impedance capacitor suitable for high frequency making
it ideal for digital circuit.
1. Circuit design
(1) The conducting polymer capacitor cannot be used in circuits that undergo frequent charging and discharging
because the resulting internal heat buildup can cause capacitor failure.
(2) Do not use the capacitor in time-constant or coupling circuits. In these type of circuit, electrical characteristics such
as capacitance can change under certain environmental conditions.
2. Capacitor handling techniques

(1) Capacitor insertion
Incorrect land size may cause problems with capacitor placement and mountability.
Refer to the land size table for appropriate design dimensions.
(2) Soldering
When using a soldering iron, set the tip temperature to no more than 300°C, and work in as short a time as possible
under 10 seconds. While soldering, do not apply strong force to the capacitor.
Reflow soldering
The conducting polymer capacitor is designed specifically for reflow soldering.
Maintain soldering conditions (pre-heating, reflow temperature, time) within the range indicated in the product
specifications. If soldering time is lengthened or temperature is higher, the heat can damage the capacitor element
and / or the molded case.
Do not perform reflow soldering more than twice.
(3) Circuit board cleaning

Capacitors can withstand immersion in solvent at 60° C or under for up to 5 minutes.
Be sure to sufficiently wash (about 3 min. with water) and dry (20 min. at 100°C) the board afterward.
3. Electrical characteristics comparison of Capacitors
Species High Frequency Temperature Allowable ripple Miniaturized
Al Electrolytic capacitor ◉
MLCC - ◉
Film Capacitor -
Tantal Capacitor ◉ ◉ ◉
Hi-CAP ◉
※ Superior ◉ Ordinary Inferior
32
PRECAUTIONS AND GUIDELINES (Conductive Polymer)
The Hi-CAP is a Conductive Polymer Solid Aluminum Capacitor that uses highly conductive polymer electrolytic
material.
Please read the following in order to get the most out of your Hi-CAP capacitor. For aluminum electrolytic capacitors,
please refer to PRECAUTIONS AND GUIDELINES
SOLID TYPES
1. Designing Device Circuits
1) Types of Circuits Where Hi-CAP Capacitors are Not to be Used
The leakage current in conductive polymer solid aluminum capacitors(hereafter called Hi-CAP) may vary depending
on thermal stresses during soldering. Avoid the use of capacitors in the following types of circuits:
① High-impedance circuits that are to sustain voltages.
② Coupling circuits
③ Time constant circuits
Because the capacitance varies depending on the environment the capacitors are used in, there is a possibility
that the capacitor can affect a time constant circuit where sensitivity to variation in capacitance is required.
④ Other circuits that are significantly affected by leakage current
2) Circuit Design
Verify the following before designing the circuit:
① The electrical characteristics of the capacitor will vary depending on differences in temperature and frequency.
You had better design after verifying the scope of these factors.
② When connecting two or more capacitors in parallel, ensure that the design takes current balancing into account.
③ When two or more capacitors are connected in series, variability in applied voltage may cause over-voltage
conditions. Contact Samwha before using capacitors connected in series.
④ Avoid putting heat generating parts either around the capacitor or on the reverse of the circuit board
3) Use in High Reliable and Critical Applications

Consult with Samwha before using these capacitors in applications involving human life: Aviation/space equipment,
Nuclear power equipment, Medical equipment and Automotive equipment, or in applications where capacitor failure
could have a major impact
4) Polarity
The Hi-CAP is a polarized solid aluminum electrolytic capacitor. Do not apply either reverse voltages or AC voltages
to the polarized capacitors, using reversed polarity may cause a short circuit. Refer to the catalog product
specifications or capacitor body to confirm the polarity prior to use
5) Operating Voltage
Do not apply a greater than rated voltage, if a voltage greater than the rated voltage is suddenly applied the leakage
current increases causing shorting. The peak voltage of superimposed AC voltages(ripple voltages) on DC voltages
must not exceed the full rated voltage. While there are specifications for surge voltages exceeding the rated
voltage, usage conditions apply, and continued operation for extended periods of time under such conditions cannot
be guaranteed.
33
6) Surge voltage
The maximum instantaneous voltage which may be applied to the terminations of the capacitor for a specified time at
any temperature with the operating temperature range.
Rated voltage (VDC) 2.5 4 6.3 10 16 20 25 35

Surge voltage (VDC) 3.3 5.2 8.2 11.5 18.4 23 25 35
7) Ripple current
Do not apply currents in excess of the rated ripple current. The superimposition of a large ripple current increases
the rate of heating within the capacitor. When excessive ripple current is imposed the internal temperature
increases which can shorten life and shorting may occur.
8) Operating temperature
Use within the stated category temperature range, if used outside this range, characteristics can deteriorate
potentially leading to problems.
9) Charging and Discharging in Capacitor

Do not use the Hi-CAP in circuits where the capacitor is repetitively charged and discharged rapidly. Repetitively
charging and discharging the capacitor rapidly may reduce the capacitance or may cause damage due to internal
heating. Use of a protective circuit to ensure reliability is recommended when rush currents exceed 20A.
10) Leakage current

The leakage current may increase when the capacitors are subjected to the conditions below. After that, however,
the leakage current will gradually decrease by self-healing action of the dielectric oxide layer when the capacitors
are applied with a voltage less than the rated voltage within the Category Temperature range. As the voltage is
closer to the rated voltage and the temperature is closer to the upper limit of Category Temperature range, the
leakage current decreases faster.
The leakage current will increase by the following factors,
① Soldering
② Testing of high temperature exposure with no voltage applied, high temperature/humidity storage, temperature
cycles, etc.
11) Failures and Service Life

Based on the KS C 6032 Standard, the failure rate for Hi-CAP(with a 60% reliability standard) is as follows:
0.5%/1,000 hours(applied the rate voltage at the upper limit of Category Temperature range)
(1) Failure Modes

① The principal failure mode is wear-out failure, that is, capacitance decreases and ESR increases, and eventually
the capacitors become open circuit failure. In addition, short circuit failure may happen with over-voltage and
excessive current applied to the capacitors.
② The failure rate would be reduced by reducing ambient temperatures, ripple current and applying voltage.
③ If the short-circuited capacitor, which may be caused by over-voltages higher than the rated voltage or other
conditions, has a large amount of current passed through, the aluminum can of the capacitor bulges and might
be expelled with odor gas emitted.
④ The product contains flammable materials. If the short causes a spark it may ignite. Please be careful when
installing the product, its position and the layout design.
▶ Increase safety by using in conjunction with a protective circuit or protective equipment.
▶ Install measures such as redundant circuits so that the failure of a part of the equipment will not cause unstable
operation.
(2) Service Life

Hi-CAP uses rubber as the sealing material, so the service life depends on the thermal integrity of this rubber.
Consequently, it is recommended to use the capacitor at a lower temperature than the maximum temperature for
the capacitor category.
34
12) Capacitor Insulation

Insulation of the capacitor's case is not guaranteed. Ensure electrical insulation between the capacitor case,
negative electrode, positive electrode and circuit pattern.
13) Capacitor Usage Environment

Do not use/expose capacitors to the following conditions.
① Oil, water, salty water, take care to avoid storage in damp locations.
② Direct sunlight
③ Toxic gases such as hydrogen, sulfide, sulfurous acids, nitrous acids, chlorine and chlorine compounds, bromine
and bromine compounds, ammonia, etc.
④ Ozone, ultraviolet rays and radiation.
14) Storage
SOLID TYPES
(1) SMD Type
① Do not sotre the Hi-CAP at high temperatures and high humidity. Avoid direct sunlight.
(Recommendable conditions 5 to 35° C, 45 to 75% RH)
② To keep good solderability, store the Hi-CAP not more than 6 months after delivery and 30 days after unseal.
Before unseal After unseal

A period of storage Within 1 year after delivery Within 30 days of unseal
(SMD) (Sealed conditions) (Packaged condition with carrier tape)
③ The Hi-CAP should not be direct contact with water, salt spray, oil spray or high humidity.
④ The Hi-CAP must not be exposed to toxic gases such as hydrogen sulfide, sulfurous acid, nitrous acid, chlorine,
ammonia, etc.
(2) LEAD Type

① Do not sotre the Hi-CAP at high temperatures and high humidity. Avoid direct sunlight.
(Recommendable conditions 5 to 35° C, 45 to 75% RH)
② To keep good solderability, store the Hi-CAP not more than 1 year after delivery and 7 days after unseal.
Before unseal After unseal

A period of storage Within 1 year after delivery
Within 7 days of unseal
(LEAD) (Sealed conditions)
③ The Hi-CAP should not be direct contact with water, salt spray, oil spray or high humidity.
④ The Hi-CAP must not be exposed to toxic gases such as hydrogen sulfide, sulfurous acid, nitrous acid, chlorine,
ammonia, etc.
35
●Taping Specifications for Lead Type Polymer Capacitors

DRAWING Ⅰ
P2 P
Δh
H P1 F
W2
A W1
W0 t
W
P0 Ød ØD0
Applicable Drawing No. Ⅰ

Description Symbol Tolerance Ø6.3 Ø8 Ø10
Body Height L +1 6, 8 9 12 13
Lead Dia. Ød ±0.05 0.45 0.60 0.60 0.6
Body Pitch P ±1.0 12.7
Feeding Hole Pitch P0 ±0.2 12.7
Feeding Hole Alignment P 1 ±0.7 5.1 3.85
Feeding Hole Alignment P2 ±1.0 6.35
Lead Center Spacing F +0.6/-0.2 2.5 3.5 5.0
Body Inclination Δh ±2.0 0
Tape Width W ±0.5 18.0
Adhesive Tape Width W0 min. 9.5 12.5
Feeding Hole Alignment W1 ±0.5 9.0
Adhesive Tape Margin W2 max. 2.0
Length from Seating Plane H ±0.5 17.5 20.0 18.5
Feeding Hole Dia. ØD0 ±0.2 4.0
Total Tape Thickness t ±0.2 0.7
Cut Lead Height A max. 11.0
Taping Code Ammo ＋ leader PC PF PA
● PACKAGING Q’ty(pcs.) / BOX

Size Ammo Ammo
ØD Case Height L H W Q’ty Tear off
6 332 230 42 1500
6.3
8 332 230 49 1500
9 332 230 49 1000 H
8
12 332 230 49 1000
L
10 13 332 190 51 500 W
● BULK PACKING QUANTITY(PCS) / BOX ● CUTTING PACKING QUANTITY(PCS) / BOX

Size Size
V-BAG INNER BOX MIDDLE BOX V-BAG INNER BOX MIDDLE BOX
D L D L
6 750 6000 24000 6 750 6000 24000
6.3 6.3
8 700 5600 22400 8 750 6000 24000
9 400 2800 11200 9 500 4000 16000
8 8
12 400 2800 11200 12 400 3200 12800
10 13 250 1500 6000 10 13 250 1500 6000
36
●Taping Specifications for SMD Type Polymer Capacitors (Vertical type)

● Carrier Tape
ØD0 +0.1 t1
E±0.1
0
P0±0.1 P2±0.1
F±0.1
W±0.3
B±0.2
t2±0.2
P1±0.1 A±0.2
ØD×L A B ØD0 E F P0 P1 P2 t1 t2 W
4×5.4 4.7 4.7 1.5 1.75 5.5 4 8 2 0.4 5.7 12
SOLID TYPES
5×5.9 5.7 5.7 1.5 1.75 7.5 4 8 2 0.4 6.3 16
6.3×4.5 6.9 6.9 1.5 1.75 7.5 4 12 2 0.4 4.7 16
6.3×5.9 7.0 7.0 1.5 1.75 7.5 4 12 2 0.4 6.3 16
8×6.9 8.7 8.7 1.5 1.75 11.5 4 12 2 0.4 7.2 24
8×11.9 8.7 8.7 1.5 1.75 11.5 4 16 2 0.4 12.3 24
10×7.9 10.7 10.7 1.5 1.75 11.5 4 16 2 0.4 8.2 24
10×12.6 10.7 10.7 1.5 1.75 11.5 4 16 2 0.5 13 24
● Reel(Taping Code : VR) ● Recommended Land Size
C
Ø382max.
Ø80±1.0
23
13±
A
0.5
2.0
B
A 3
ØD×L A ØD×L Q’ty/Reel(pcs) Q’ty/Box(pcs) ØD×L A B C

4×5.4 13 4×5.4 2000 20000 4×5.4 1.0 6.2 1.6
5×5.9 17 5×5.9 1500 15000 5×5.9 1.4 7.4 1.6
6.3×4.5 17 6.3×4.5 1000 10000 6.3×4.5 2.1 9.1 1.6
6.3×5.9 17 6.3×5.9 1000 10000 6.3×5.9 2.1 9.1 1.6
8×6.9 25 8×6.9 1000 10000 8×6.9 2.8 11.1 1.9
8×11.9 25 8×11.9 400 4000 8×11.9 2.8 11.1 1.9
10×7.9 25 10×7.9 500 5000 10×7.9 4.3 13.1 1.9
10×12.6 25 10×12.6 400 4000 10×12.6 4.3 13.1 1.9
●Recommendable reflow soldering temperature

5s
250 Peak temperature

Temperature on the surface
200
160
C)
of capacitor (°
120s 30s
0 Time (sec.)
37
FA Chip type, With Conductive Polymer

Series
Hi-CAP
・Low ESR, high ripple current

・Designed for surface mounting on high density PC board
・Load life for 2000 hours at 105°
C
・Complied to the RoHS directive
Item Characteristics
Operating temperature range -55 ~ +105°C
Leakage current max. Less than or equal to the value of Table1
Capacitance tolerance ±20% at 120Hz, 20° C
Dissipation factor max. Less than or equal to the value of Table1
ESR Less than or equal to the value of Table1
Temperature characteristics Z-55°C / Z+20°C Z+105°C / Z+20°C
(Impedance ratio at 100kHz) 0.75 ~ 1.25 0.75 ~ 1.25
Load life Leakage current Less than specified value
(after application of the rated Capacitance change Within ±20% of initial value
voltage for 2000 hours at 105° C,
In case of 25WV is applied 20V) tanδ Less than 150% of specified value
Resistance to soldering heat Leakage current Less than specified value

(Refer to Page 37 for soldering Capacitance change Within ±10% of initial value
recommendation) tanδ Less than 130% of specified value
In case of some problems for measured values, measure after applying rated voltage for 2.5 to 20V products or 20V derating voltage for 25V products for 120
minutes at 105°C.
● DRAWING Unit : mm
< Dimensions >

＋ Positive
● PART NUMBER SYSTEM (See Page 52)
Plastic plateform
0.5 max.
0.3 max. C±0.2

Size ØD L B C E A R
4×5.4 4 5.4 4.3 4.3 1.0 1.9 0.5~0.8
A±0.2
5×5.9 5 5.9 5.3 5.3 1.4 2.2 0.5~0.8

ØD±0.5
6.3 5.9 6.6 6.6 2.2 2.45 0.5~0.8

B±0.2
6.3×5.9
E
8×6.9 8 6.9 8.3 8.3 3.2 2.9 0.5~0.8

A±0.2
8×11.9 8 11.9 8.3 8.3 3.2 2.9 0.8~1.1

10×7.9 10 7.9 10.3 10.3 4.6 3.2 0.8~1.1
－ Negative
L±0.3 R 10×12.6 10 12.6 10.3 10.3 4.6 3.2 0.8~1.1
< Marking >
Capacitance Capacitance
Series Code Series Code
＋＋
※Voltage ※Voltage
10FA
Lot No. Lot No.

10A
6.3V is 6 6.3V is 6
－－
Negative Polarity Negative Polarity
(Ø4, Ø5) (Ø6.3, Ø8, Ø10)
Series Code“A”
38
FA Series
● Table1. FA(SMD type) Series Characteristics List

ESR(mΩ)max. Ripple current Dissipation factor Leakage Current
WV μF ØD(mm) L(mm) (mA rms)at 105°C (μA)(max.)
100~300kHz 120Hz
100kHz after 2 minutes
2.5 220 6.3 5.9 23 2390 0.12 110
2.5 680 8 11.9 13 4520 0.15 340
2.5 1500 10 12.6 12 5440 0.18 750
4 33 4 5.4 200 740 0.15 66
4 39 5 5.9 70 1100 0.12 78
4 68 5 5.9 60 1400 0.12 136
4 150 6.3 5.9 40 1810 0.12 120
4 150 8 6.9 35 2560 0.12 120
4 330 8 6.9 35 2560 0.12 264
SOLID TYPES
4 560 8 11.9 13 4520 0.15 448
4 680 10 7.9 25 3700 0.12 544
4 1200 10 12.6 12 5440 0.18 960
6.3 22 4 5.4 200 740 0.12 69.3
6.3 47 5 5.9 70 1100 0.12 148
6.3 82 6.3 5.9 45 1700 0.12 103
6.3 100 6.3 5.9 40 1810 0.12 126
6.3 120 6.3 5.9 17 2780 0.12 151
6.3 220 8 6.9 35 2560 0.12 277
6.3 220 10 7.9 25 3700 0.12 277
6.3 330 10 7.9 25 3700 0.12 416
6.3 470 10 7.9 25 3700 0.12 592
6.3 470 8 11.9 15 4210 0.12 592
6.3 820 10 12.6 12 5440 0.15 775
10 4.7 4 5.4 240 670 0.08 23.5
10 6.8 4 5.4 240 670 0.08 34
10 10 4 5.4 220 700 0.09 50
10 15 4 5.4 200 740 0.10 75
10 33 5 5.9 70 1100 0.10 165
10 47 6.3 5.9 50 1620 0.12 94
10 56 6.3 5.9 45 1700 0.12 112
10 120 8 6.9 35 2560 0.12 240
10 150 8 6.9 35 2560 0.12 300
10 150 10 7.9 30 3020 0.12 300
10 270 10 7.9 25 3700 0.12 540
10 330 10 7.9 25 3700 0.12 660
10 330 8 11.9 17 3950 0.15 660
10 560 10 12.6 13 5230 0.15 840
16 3.3 4 5.4 260 660 0.07 26.4
16 15 5 5.9 120 1020 0.10 120
16 22 5 5.9 90 1060 0.10 176
16 39 6.3 5.9 50 1620 0.10 125
16 56 8 6.9 45 1890 0.12 179
16 82 8 6.9 40 2120 0.12 262
16 100 10 7.9 35 2670 0.12 320
16 150 10 7.9 30 3020 0.12 480
16 180 10 7.9 30 3020 0.12 576
16 180 8 11.9 20 3640 0.15 576
16 330 10 12.6 16 4720 0.15 792
20 10 5 5.9 120 1020 0.10 100
20 22 6.3 5.9 60 1450 0.10 88
20 27 6.3 5.9 60 1450 0.10 108
20 33 8 6.9 45 1890 0.12 132
20 47 8 6.9 45 1890 0.12 188
20 56 10 7.9 40 2400 0.12 224
20 68 10 7.9 40 2400 0.12 272
20 100 8 11.9 24 3320 0.15 400
20 150 10 12.6 20 4320 0.15 600
25 6.8 6.3 5.9 80 1200 0.10 85
25 10 8 6.9 60 1500 0.10 125
25 22 10 7.9 50 2000 0.10 275
25 33 8 11.9 30 2980 0.12 413
25 56 10 12.6 28 3800 0.12 700
● FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency 120Hz 1kHz 10kHz 100 ~ 500kHz
Coefficient 0.05 0.3 0.7 1
39
FH Chip type, Large Capacitance, Low ESR

Series
Hi-CAP
・Large capacitance, Low ESR than FA Series

Leakage current Less than specified value
Load life Capacitance change Within ±20% of initial value
(after application of the rated
voltage for 2000 hours at 105° C) ESR Less than 150% of specified value
tanδ Less than 150% of specified value

In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 105°
C.
< Dimensions >

＋ Positive
Plastic plateform
0.5 max.
0.3 max. C±0.2 Size ØD L B C E A R

5×5.9 5 5.9 5.3 5.3 1.4 2.2 0.5~0.8
A±0.2
6.3×5.9 6.3 5.9 6.6 6.6 2.2 2.45 0.5~0.8

ØD±0.5
B±0.2
8×6.9 8 6.9 8.3 8.3 3.2 2.9 0.5~0.8

E
A±0.2
8×11.9 8 11.9 8.3 8.3 3.2 2.9 0.8~1.1

10×12.6 10 12.6 10.3 10.3 4.6 3.2 0.8~1.1
－ Negative
L±0.3 R
< Marking >
＋＋
10FH
Lot No. Lot No.

10H
6.3V is 6 6.3V is 6
－－
(Ø5) (Ø6.3, Ø8, Ø10)
Series Code“H”
40
FH Series
● Table 1. FH(SMD type) Series Characteristics List
Size Ripple current Dissipation Leakage Current

ESR(mΩ)max.
WV μF (mA rms) factor at 120Hz (μA) (max.)
L(mm) 100kHz~300kHz
ØD(mm) at 105°C, 100kHz (max.) after 2 minutes
2.5 180 5 5.9 24 2200 0.12 300
2.5 330 6.3 5.9 15 3160 0.12 500
2.5 390 6.3 5.9 25 2410 0.12 300
2.5 680 8 6.9 20 3370 0.12 500
2.5 820 8 11.9 9 5380 0.15 500
2.5 1500 8 11.9 10 5150 0.15 750
2.5 2700 10 12.6 12 5080 0.15 1350
4 150 5 5.9 23 2240 0.12 300
SOLID TYPES
4 330 6.3 5.9 21 2630 0.12 300
4 560 8 6.9 22 3220 0.12 500
4 560 8 11.9 9 5380 0.15 500
4 1200 8 11.9 12 4700 0.15 960
4 1500 8 11.9 12 4700 0.15 1200
6.3 100 5 5.9 25 2150 0.12 300
6.3 220 6.3 5.9 15 3110 0.12 300
6.3 330 6.3 5.9 17 3390 0.12 416
6.3 390 8 6.9 22 3220 0.12 491
6.3 820 8 11.9 12 4700 0.15 1033
10 68 5 5.9 30 1970 0.12 300
10 120 6.3 5.9 27 2320 0.12 300
10 270 8 6.9 22 3220 0.12 500
16 39 5 5.9 35 1820 0.12 300
16 68 6.3 5.9 30 2200 0.12 300
16 120 8 6.9 27 2900 0.12 500

Frequency 120Hz 1kHz 10kHz 100~500kHz
41
FT Chip type, Guaranteed at 125°

Series
C Hi-CAP
・The FT Series is very reliable, guaranteeing performance

・Suitable for use in smoothing circuits of vehicle-mounted equipment,
industrial equipment, etc

C.
＋ Positive
Capacitance Plastic plateform ● PART NUMBER SYSTEM (See Page 52)
0.5 max.
Series Code 0.3 max. C±0.2 Size ØD L B C E A R

6.3×5.9 6.3 5.9 6.6 6.6 2.2 2.45 0.5~0.8
A±0.2
＋
※Voltage 8×6.9 8 6.9 8.3 8.3 3.2 2.9 0.5~0.8
ØD±0.5
10FT
Lot No.
B±0.2
6.3V is 6
E
8×11.9 8 11.9 8.3 8.3 3.2 2.9 0.8~1.1

A±0.2
－ 10×7.9 10 7.9 10.3 10.3 4.6 3.2 0.8~1.1

10×12.6 10 12.6 10.3 10.3 4.6 3.2 0.8~1.1
Negative Polarity － Negative
L± 0.3 R
● Table 1. FT(SMD type) Series Characteristics List
ESR(mΩ)max. Ripple current Ripple current Dissipation factor Leakage Current

ØD
WV μF L(mm) (100kHz)(mA rms) (100kHz)(mA rms) (μA)(max.)
(mm) 100~300kHz 105°
C≺T×≦125° C T×≦105° C 120Hz
after 2 minutes
10 56 6.3 5.9 45 538 1700 0.12 112
16 82 8 6.9 40 670 2120 0.12 262
25 10 6.3 5.9 65 474 1500 0.10 50
25 22 8 6.9 48 580 1835 0.10 110
25 39 10 7.9 45 664 2100 0.10 195
25 47 8 11.9 30 943 2980 0.12 235
25 82 10 12.6 28 1202 3800 0.12 410
35 8.2 8 6.9 70 400 1300 0.10 57
35 18 10 7.9 60 550 1800 0.10 126
35 22 8 11.9 50 700 2300 0.12 154
35 47 10 12.6 30 1150 3650 0.12 329

42
FZ Chip type, Guaranteed at 105°

Series
C 5000 hours Hi-CAP
・Series has long life time than the FA Series

・Suitable for use in flat panel TV set and the others
industrial equipments, etc
SOLID TYPES

Load life
Capacitance change Within ±20% of initial value
ESR Less than 200% of specified value
voltage for 5000 hours at 105° C)

(Refer to page 37 for soldering Capacitance change Within ±10% of initial value
In case of some problems for measured values, measure after applying rated voltage for 4 to 20V products or 20V derating voltage for 25V products for 120
minutes at 105°C.
< Dimensions >

＋ Positive
Plastic plateform
0.5 max.
0.3 max. C±0.2

Size ØD L B C E A R
4×5.4 4 5.4 4.3 4.3 1.0 1.9 0.5~0.8
A±0.2
5×5.9 5 5.9 5.3 5.3 1.4 2.2 0.5~0.8

ØD±0.5
B±0.2
6.3×5.9 6.3 5.9 6.6 6.6 2.2 2.45 0.5~0.8

E
A±0.2
8×6.9 8 6.9 8.3 8.3 3.2 2.9 0.5~0.8

10×7.9 10 7.9 10.3 10.3 4.6 3.2 0.8~1.1
－ Negative
L±0.3 R
< Marking >
＋＋
10FZ
Lot No. Lot No.

10Z
6.3V is 6 6.3V is 6
－－
(Ø4, Ø5) (Ø6.3, Ø8, Ø10)
Series Code“Z”
43
FZ Series
● Table 1. FZ(SMD type) Series Characteristics List

Ripple current Dissipation factor Leakage Current
ESR(mΩ)max.
WV μF ØD(mm) L(mm) (mA rms)at 105°C (μA)(max.)
100~300kHz 120Hz
4 33 4 5.4 200 740 0.15 66
4 68 5 5.9 30 1970 0.12 300
4 150 6.3 5.9 22 2570 0.12 300
4 270 8 6.9 22 3220 0.12 500
4 680 10 7.9 20 4130 0.12 544
6.3 22 4 5.4 200 740 0.12 69.3
6.3 47 5 5.9 30 1970 0.12 300
6.3 120 6.3 5.9 22 2570 0.12 300
6.3 220 8 6.9 22 3220 0.12 500
6.3 470 10 7.9 20 4130 0.12 592
10 10 4 5.4 220 700 0.1 50
10 15 4 5.4 200 740 0.1 75
10 33 5 5.9 70 1100 0.12 165
10 68 6.3 5.9 30 2200 0.12 300
10 150 8 6.9 30 2760 0.12 500
10 150 10 7.9 30 3020 0.12 300
10 330 10 7.9 24 3770 0.12 660
16 22 5 5.9 90 1060 0.1 176
16 39 6.3 5.9 24 2460 0.12 300
16 82 8 6.9 30 2760 0.12 262
16 100 10 7.9 35 2670 0.12 320
16 180 10 7.9 29 3430 0.12 576
20 22 6.3 5.9 60 1450 0.1 88
20 47 8 6.9 45 1890 0.12 188
25 10 8 6.9 60 1500 0.1 125

44

Upgrade
FB Lead type, With Conductive Polymer

Series
Hi-CAP

C
SOLID TYPES
voltage for 2000 hours at 105° C, Capacitance change Within ±20% of initial value
In case of 25WV is applied 20V) tanδ Less than 150% of specified value
In case of some problems for measured values, measure the after applying rated voltage for 2.5 to 20V products or 20V derating voltage for 25V products for
120 minutes at 105°C.

Laminated Case
Ød ±0.05
Size ØD L P Ød β
＋
5×9 5 9.0 2.5 0.45 1.5
ØD+0.5max.
6.3×6 6.3 6.0 2.5 0.45 1.5

P±0.5
6.3×8 6.3 8.0 2.5 0.45 1.5

－ 8×7 8.0 7.0 2.5 0.45 1.5
8×9 8.0 9.0 3.5 0.60 1.5
L +βmax. 15min. 4min.
8×12 8.0 12.0 3.5 0.60 1.5
10×13 10.0 13.0 5.0 0.60 1.5
Capacitance Series Code
＋
※Voltage
6FB
Lot No.
100
6.3V is 6
Negative Polarity
45
FB Series
● Table 1. FB(Lead type) Series Characteristics List

Ripple current Tangent of
ESR(mΩ)max. Leakage Current
WV μF ØD(mm) L(mm) (mA rms)at 105°C
100~300kHz loss angle(max.) (μA)(max.)
100kHz
2.5 390 6.3 8 20 3160 0.10 195
2.5 560 8 9 7 6100 0.10 280
2.5 680 8 9 7 6100 0.10 340
2.5 820 8 9 7 6100 0.10 410
2.5 1000 8 9 7 6100 0.10 500
2.5 1500 8 12 8 5500 0.10 750
2.5 2700 10 13 8 5560 0.10 1350
2.5 3300 10 13 8 6650 0.10 1650
4 100 6.3 6 40 1810 0.10 80
4 150 6.3 6 40 1810 0.10 120
4 220 6.3 8 35 2560 0.10 176
4 270 6.3 8 20 3160 0.10 216
4 330 6.3 8 24 3300 0.10 264
4 390 6.3 8 24 3300 0.10 312
4 470 8 9 8 5700 0.10 376
4 560 8 9 7 6100 0.10 448
4 680 8 9 7 6100 0.10 544
4 1200 8 12 8 5700 0.10 960
6.3 82 6.3 6 45 1700 0.10 103
6.3 150 6.3 8 35 2560 0.10 189
6.3 220 6.3 8 20 3160 0.10 277
6.3 330 8 9 28 3190 0.10 416
6.3 470 8 9 8 5700 0.10 592
6.3 680 8 9 7 6640 0.10 857
6.3 820 8 12 7 6640 0.10 1033
6.3 1000 8 12 8 6100 0.10 1260
6.3 1200 10 13 10 5560 0.10 1520
6.3 1500 10 13 10 5560 0.10 1890
10 47 6.3 6 25 2820 0.10 94
10 56 6.3 6 25 2820 0.10 112
10 68 6.3 6 25 2820 0.10 136
10 100 6.3 8 25 2820 0.10 200
10 120 6.3 8 35 2560 0.10 240
10 150 6.3 8 25 2820 0.10 300
10 270 8 12 9 4710 0.10 540
10 330 8 12 9 4710 0.10 660
10 390 8 12 9 5650 0.10 780
10 470 8 12 8 5650 0.10 940
10 560 10 13 8 5650 0.10 1120
10 680 10 13 7 6100 0.10 1360
46
FB Series
● Table 1. FB(Lead type) Series Characteristics List

Ripple current Tangent of
ESR(mΩ)max. Leakage Current
WV μF ØD(mm) L(mm) (mA rms)at 105°C
100~300kHz loss angle(max.) (μA)(max.)
100kHz
12 330 5 9 15 3160 0.10 100
16 39 6.3 6 50 1620 0.10 124
16 82 6.3 8 25 2120 0.10 262
16 100 6.3 8 25 2820 0.10 320
16 180 8 12 16 4360 0.10 576
16 270 8 12 11 5000 0.10 864
16 330 10 13 10 6100 0.10 1056
SOLID TYPES
16 470 10 13 10 6100 0.10 1504
20 22 6.3 6 60 1450 0.12 88
20 47 6.3 8 25 2820 0.12 188
20 56 6.3 8 25 2820 0.12 224
20 68 6.3 8 25 2820 0.12 272
20 100 8 12 24 3320 0.12 400
20 150 10 13 20 4320 0.12 600
20 560 10 13 12 5400 0.12 2240
25 6.8 6.3 6 80 1200 0.12 85
25 10 6.3 8 60 1500 0.12 125
25 18 6.3 8 40 2230 0.12 225
25 22 8 12 40 2230 0.12 275
25 33 8 12 30 2980 0.12 413
25 56 8 12 30 3800 0.12 700
25 68 8 12 25 3320 0.12 850
25 82 8 12 24 3320 0.12 1025
25 100 8 12 20 4320 0.12 1250
35 10 8 7 60 1300 0.12 70
35 120 10 13 18 4400 0.12 840
35 150 10 13 16 4400 0.12 1050
47
FJ Lead type, With Conductive Polymer

Series
Hi-CAP

・Load life for 2000 hours at for charger 105°
C
・For charger
C.
Unit : mm
● DRAWING
Laminated Case
Ød ±0.05
Size ØD L P Ød β
＋ 5×8 5.0 8.0 2.0 0.45 1.5
ØD+0.5max.
5×9 5.0 9.0 2.0 0.45 1.5

P±0.5
6.3×8 6.3 8.0 2.5 0.45 1.5

－
8×9 8.0 9.0 3.5 0.60 1.5

8×12 8.0 12.0 3.5 0.60 1.5
10×13 10.0 13.0 5.0 0.60 1.5
Series Code Voltage Capacitance Series Code
＋＋
※Voltage
6.3 J
Lot No. Lot No.

4FJ
560
330
Capacitance 6.3V is 6
－－
(Ø5) (Ø6.3, Ø8, Ø10)
Series Code“J”
48
FJ Series
● Table 1. FJ(Lead type) Series Characteristics List

Ripple current Leakage Current
ESR(mΩ)max. Dissipation factor
WV μF ØD(mm) L(mm) (mA rms) at 105°C (μA)(max.)
100~300kHz 120Hz
2.5 330 6.3 8 7 5600 0.10 500
2.5 560 6.3 8 7 5600 0.10 500
2.5 560 8 9 8 4700 0.10 280
2.5 820 6.3 8 7 5600 0.10 513
2.5 820 8 9 5 7200 0.10 500
2.5 820 8 12 5 7200 0.10 500
2.5 1000 8 9 7 6100 0.10 500
SOLID TYPES
2.5 2700 10 13 10 5560 0.10 1350
4 560 6.3 8 7 5600 0.10 560
4 560 8 9 5 7200 0.10 500
4 560 8 12 5 7200 0.10 500
4 680 8 12 5 7200 0.10 544
4 820 10 13 7 6640 0.10 656
6.3 270 5 8 7 3700 0.10 500
6.3 330 5 8 7 3700 0.10 416
6.3 390 5 8 11 3100 0.10 130
6.3 470 8 9 8 5700 0.10 592
6.3 470 8 12 8 5700 0.10 592
6.3 560 8 9 7 6100 0.10 706
6.3 680 6.3 8 7 3160 0.10 856
6.3 680 10 13 7 6640 0.10 857
6.3 1500 10 13 10 5560 0.10 1890
6.8 330 5 8 10 3700 0.10 448
6.8 390 5 9 10 3360 0.10 100
7.0 270 5 8 7 3000 0.10 100
7.5 330 5 9 10 3360 0.10 495
7.5 390 5 9 10 3360 0.10 100
7.5 470 5 9 11 3100 0.10 210
16 100 6.3 8 10 4680 0.10 500
16 180 8 12 16 4360 0.10 576
16 270 8 12 11 5000 0.10 864
16 470 10 13 10 6100 0.10 1504

49
FV Lead type, With Conductive Polymer

Series
Hi-CAP

C
・Mother board and VGA card for computer
C.
Unit : mm
● DRAWING
Laminated Case
Ød ±0.05
＋
ØD+0.5max.
Size ØD L P Ød β
P±0.5
6.3×8 6.3 8.0 2.5 0.45 1.5

－ 8×9 8.0 9.0 3.5 0.60 1.5
8×12 8.0 12.0 3.5 0.60 1.5
Capacitance Series Code
＋
※Voltage
4FV
Lot No.
560
6.3V is 6
Negative Polarity
● Table 1. FV(Lead type) Series Characteristics List

Ripple current Leakage Current
ESR(mΩ)max. Dissipation factor
WV μF ØD(mm) L(mm) (mA rms) at 105°C (μA) (max.)
100~300kHz 120Hz
6.3 8 7 5000 0.10 500
2.5 820
8 9 7 6100 0.10 410
4 560 6.3 8 7 5000 0.10 500
470 6.3 8 8 4700 0.10 592
6.3 560 6.3 8 8 4700 0.10 706
560 8 9 8 6100 0.10 706
100 6.3 8 25 2820 0.10 320
16 270 8 12 11 5000 0.10 864

50
3 SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
PART NUMBER SYSTEM
●Part Number System
➊ ➋ ➌ ➍ ➎ ➏ ➐ ➑
Series Name Rated Voltage Capacitance Cap. Tol. Case Diameter Case Height Taping Code Internal Control
Code
➊ Series Name ➏ Case Height

See page 6. ex) 5.3mm 005
5.8mm 006
6.2mm 06B
➋ Rated Working Voltage 7.7mm 07K
10mm 010
WV 4 6.3 10 16 25 35 50 13.5mm 13M
Code 0G 0J 1A 1C 1E 1V 1H
WV 63 100 160 200 250 400 450 ➐ Taping Code

Code 1J 2A 2C 2D 2E 2G 2W VR (Reel Type)
➌ Capacitance
ex) 0.47μF 474
4.7μF 475
47μF 476
470μF 477
4700μF 478
Capacitance Tolerance
Tolerance (%) ±20
Code M
➎ Case Diameter
ex) Ø4 04
Ø5 05
Ø6.3 6L
Ø8 08
Ø10 10
Ø12.5 12
52
●Taping Specifications for Chip Type Capacitors

● Carrier Tape
ØD0 +0.1 t1
E±0.1
0
・Fig.1 P0±0.1 P2±0.1
F±0.1
W±0.3
B±0.2
t2±0.2
P1±0.1 A±0.2
E±0.1
ØD0 +0.1 t1
・Fig.2 P0±0.1 P2±0.1
0
F±0.1
W±0.3
B±0.2
t2±0.2
0.2
P1±0.1 A±0.2 R0.75
ØD×L A B ØD0 E F P0 P1 P2 t1 t2 W Fig.

4 × 5.3 4.7 4.7 1.5 1.75 5.5 4.0 8.0 2.0 0.4 5.7 12.0
5 × 5.3 5.7 5.7 1.5 1.75 5.5 4.0 12.0 2.0 0.4 5.7 12.0
CHIP TYPES
6.3× 5.3 7.0 7.0 1.5 1.75 7.5 4.0 12.0 2.0 0.4 5.7 16.0
6.3× 5.8 7.0 7.0 1.5 1.75 7.5 4.0 12.0 2.0 0.4 6.3 16.0
1
6.3× 7.7 7.0 7.0 1.5 1.75 7.5 4.0 12.0 2.0 0.4 8.2 16.0
8 × 6.2 8.7 8.7 1.5 1.75 7.5 4.0 12.0 2.0 0.4 6.8 16.0
8 × 10 8.7 8.7 1.5 1.75 11.5 4.0 16.0 2.0 0.4 11.0 24.0
10 × 10 10.7 10.7 1.5 1.75 11.5 4.0 16.0 2.0 0.4 11.0 24.0
12.5×13.5 14.0 14.0 1.5 1.75 14.2 4.0 24.0 2.0 0.5 14.0 32.0 2
● Reel (Taping code : VR) ● Polarity ● Recommended Land Size

direction
Unreel
X
Ø382max.
Ø80±1.0
Y Z Y
23
13±
0.5
2.0
A 1.5
ØD×L A ØD×L Q’ty/Reel(pcs.) Q’ty/Box(pcs.) ØD×L X Y Z

4 × 5.3 14 4 × 5.3 2000 20000 4 × 5.3 1.6 2.6 1.0
5 × 5.3 14 5 × 5.3 1000 10000 5 × 5.3 1.6 3.0 1.4
6.3 × 5.3 18 6.3 × 5.3 1000 10000 6.3 × 5.3 1.6 3.5 2.0
6.3 × 5.8 18 6.3 × 5.8 1000 10000 6.3 × 5.8 1.6 3.5 2.0
6.3 × 7.7 18 6.3 × 7.7 900 9000 6.3 × 7.7 1.6 3.5 2.0
8 × 6.2 18 8 × 6.2 1000 10000 8 × 6.2 2.5 4.0 2.0
8 × 10 26 8 × 10 500 3000 8 × 10 2.5 3.5 3.0
10 × 10 26 10 × 10 500 3000 10 × 10 2.5 4.0 4.0
12.5×13.5 34 12.5×13.5 200 1000 12.5×13.5 4.0 7.5 7.0
53
Reflow soldering method for the chip aluminum electrolytic capacitor
1. Recommended conditions for reflow soldering

The chip aluminum electrolytic capacitor is subjected to soldering by reflow method.
Temperature and time conditions of reflow soldering shall be set as per each temperature profile shown below
as a standard. The following are recommended conditions in the case of reflow soldering method for the chip
aluminum electrolytic capacitor.
(1) The capacitor shall not be subjected to either flow or dip soldering method.
(2) Avoid soldering twice by reflow. The number of reflow time for chip aluminum electrolytic capacitor shall be once
basically. If this type of capacitor has to be inevitably subjected to the reflow twice, enough cooling time between
the first and the second reflow (at least more than 30 minutes) shall be taken to avoid the consecutive reflows
by all means.
(3) The touch up work with a soldering iron is allowed after the reflow soldering (Temperature of soldering iron : MAX
400°C, Time : 5 sec.), provided that carefully attention shall be paid lest a soldering iron should directly touch the
capacitor body or its resin bottom base.
2. RECOMMENDED REFLOW SOLDERING CONDITIONS
Tp
Tp
Critical Zone
TL to TP
Ramp-up
TL
Tsmax TL
Temperature
Tsmin
Ts
Preheat Ramp
-Down
25
t (25°
C to Peak)
Time
Soldering condition
Profile Feature
Ø4 ~ Ø10 Ø12.5
Average Ramp-up Rate (TL to TP) 3°
C / second max. 3°
C / second max.
Temperature Min. (TS min) 150°C 150°C
Preheat Temperature Max. (TS max) 200°C 200°C
Time (TS min to TS max) 60 ~ 150 seconds 40~120 seconds
TS max to TL -Ramp-up Rate 3°C / second max. 3°
C / second max.
Time Temperature (TL) 217°C 217°C
maintained
above Time (tL) 60 ~ 90 seconds 40 ~ 60 seconds
Peak/classification Temperature (TP) 250°C 240°C
Time within 5°
C of actual peak temperature(TP) 10 seconds max. 10 seconds max.
Ramp-Down rate 3°C / second max. 3°
C / second max.
Time 25° C to peak temperature 8 minute max. 8 minute max.
54
SC Chip type, Standard

Series Solvent Proof
WV≦100V
・Chip type higher capacitance in larger case sizes

・Applicable to automatic insertion machine using carrier tape
Operating temperature range -40 ~ +85°
C
WV≦100 I = 0.01CV or 3μA whichever is greater (after 2 minutes)
Leakage current max.
WV≧160 I = 0.04CV + 100μA(after 1 minutes)
Capacitance tolerance ±20% at 120Hz, 20°
C
Dissipation factor max. WV 4 6.3 10 16 25 35 50 63 100 160 200 250 400 450
(at 120Hz, 20°C) tanδ 0.40 0.35 0.24 0.20 0.16 0.15 0.12 0.12 0.12 0.20 0.20 0.20 0.25 0.25
WV 4 6.3 10 16 25 35 ~ 100 160 ~ 250 400 ~ 450

Low temperature characteristics
Z-25°
C/Z+20°
C 6 5 4 3 2 2 3 6
(Impedance ratio at 120Hz)
Z-40°
C/Z+20°
C 12 10 8 6 4 3 6 10

(after application of the rated Capacitance change Within ±20% of initial value (Small size : ±25%)
voltage for 2000 hours at 85° C) tanδ Less than 200% of the specified value
After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.
Shelf life (at 85°
C)
The measurement shall be performed at 20° C by the KS C IEC 60384 - 4
The following specifications shall be satisfied when the capacitors are restored to 20°
C
after exposing them at 250° C for 10 seconds.
CHIP TYPES
tanδ Less than specified value
Unit : mm
● DRAWING -Series code of SC is “V”
(Ø4, Ø5) ＋ Positive ØD×L W A B C E R

Capacitance Series Code Plastic plateform
4×5.3 4.8 4.3 4.3 1.0 0.5~0.8
0.4 max.
0.3 max. C±0.2 5×5.3 5.8 5.3 5.3 1.4 0.5~0.8

6.3×5.3 2.4 6.6 6.6 2.2 0.5~0.8
＋
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
ØD±0.5
W±0.2
Lot No.
E±0.2
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8

B±0.2
6V
47
※Voltage
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8
－ 8×10 2.9 8.3 8.3 3.1 0.8~1.1
10×10 3.2 10.3 10.3 4.5 0.8~1.1
※Voltage mark for 5.3±0.2 R
－ Negative 12.5×13.5 4.6 12.8 12.8 4.5 0.8~1.4
6.3V is 6
(Ø6.3,Ø8×6.2)
(Ø12.5)
V
(Ø8×10, Ø10×10)
V
55
SC series
● DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT

WV 4 6.3 10 16 25 35 50
μF
0.1 4×5.3 3.2
0.22 4×5.3 4.7
0.33 4×5.3 5.7
0.47 4×5.3 6.8
1.0 4×5.3 10
2.2 4×5.3 11 4×5.3 15
3.3 4×5.3 15 4×5.3 16 4×5.3 18
4×5.3 24
4.7 4×5.3 16 4×5.3 18 4×5.3 19
5×5.3 25
4×5.3 24 4×5.3 27 5×5.3 41
10 4×5.3 16 4×5.3 19 4×5.3 21 4×5.3 21
5×5.3 30 5×5.3 32 6.3×5.3 43
4×5.3 28 4×5.3 30 5×5.3 41 6.3×5.3 71
22 4×5.3 24 4×5.3 29 6.3×5.3 55
5×5.3 36 5×5.3 41 6.3×5.3 53 6.3×5.8 73
4×5.3 30 4×5.3 34 5×5.3 43 5×5.3 50 6.3×5.3 65 6.3×7.7 94
33 4×5.3 29
5×5.3 41 5×5.3 44 6.3×5.3 58 6.3×5.3 64 6.3×5.8 67 8×6.2 95
4×5.3 36 5×5.3 47 5×5.3 52 6.3×5.3 70 6.3×7.7 94 6.3×7.7 105
47 4×5.3 35
5×5.3 48 6.3×5.3 62 6.3×5.3 69 6.3×5.8 72 8×6.2 105 8×10 140
5×5.3 54 5×5.3 60 6.3×5.3 80 6.3×5.3 88 6.3×7.7 132 8×10 181
100 8×6.2 145
6.3×5.3 68 6.3×5.3 82 6.3×5.8 82 6.3×5.8 91 8×10 175 10×10 195
6.3×7.7 173 6.3×7.7 162 8×10 232
220 6.3×5.3 93 6.3×5.8 91 10×10 265 10×10 320
8×6.2 175 8×10 215 10×10 250
6.3×7.7 188
330 8×10 240 8×10 270 10×10 305 10×10 360 12.5×13.5 600
8×6.2 190
8×10 307
470 8×10 265 8×10 290 10×10 400 12.5×13.5 600
10×10 330
8×10 370
1000 10×10 454 12.5×13.5 710 12.5×13.5 820
10×10 400
1500 10×10 480 12.5×13.5 850 12.5×13.5 870
Ripple current (mA r ms) at 85°

C, 120Hz
2200 12.5×13.5 890 12.5×13.5 960
Case size ØD X L (mm)
56
SC series

μF WV 63 100 160 200 250 400 450
2.2 10×10 85
3.3 6.3×5.8 29 10×10 90 10×10 100

6.3×5.8 35
4.7 6.3×5.8 31 10×10 100 10×10 100 12.5×13.5 115 12.5×13.5 115
8×6.2 40
10 6.3×5.8 46 8×10 77 10×10 100 12.5×13.5 150 12.5×13.5 150
22 8×6.2 96 8×10 100 12.5×13.5 240 12.5×13.5 260
33 8×10 117 10×10 130 12.5×13.5 260
47 10×10 140 10×10 155 Ripple current (mA r ms) at 85°

C, 120Hz
68 10×10 160 12.5×13.5 350
100 12.5×13.5 370 12.5×13.5 420
220 12.5×13.5 550
CHIP TYPES
Frequency 50Hz 120Hz 300Hz 1kHz 10kHz≦
Coefficient 0.70 1.00 1.17 1.36 1.50
57
RC Chip type, Wide Temperature Range

・Wide operating temperature range of -55 ~ +105° C

Leakage current max. I = 0.01CV or 3μ
A whichever is greater (after 2 minutes)
Dissipation factor max. WV 6.3 10 16 25 35 50
(at 120Hz, 20°C) tanδ 0.27 0.23 0.19 0.15 0.13 0.11
WV 6.3 10 16 25 35 50
Z-25°
C/Z+20°
C 3 3 2 2 2 2
Z-55°
C/Z+20°
C 8 5 4 3 3 3

voltage for 1000 hours at 105° C) tanδ Less than 200% of specified value
Shelf life (at 105°
C)
C
Unit : mm
● DRAWING (See page 55)
-Series code of RC is “F”

μF WV 6.3 10 16 25 35 50
0.1 4×5.3 2
0.22 4×5.3 3
0.33 4×5.3 4
0.47 4×5.3 5
1.0 4×5.3 7
2.2 4×5.3 11
3.3 4×5.3 13
4.7 4×5.3 13 4×5.3 14 5×5.3 18
10 4×5.3 17 5×5.3 23 5×5.3 24 6.3×5.3 31
22 4×5.3 22 5×5.3 27 5×5.3 30 6.3×5.3 39 6.3×5.3 42 6.3×5.8 45
33 5×5.3 31 5×5.3 33 6.3×5.3 43 6.3×5.3 48 6.3×5.8 52 6.3×7.7 60
47 5×5.3 36 6.3×5.3 46 6.3×5.3 51 6.3×5.8 59 6.3×5.8 63 6.3×7.7 63
100 6.3×5.3 50 6.3×5.8 64 6.3×5.8 64 6.3×7.7 91 8×10 296 10×10 295
220 6.3×7.7 86 6.3×7.7 105 6.3×7.7 105 8×10 340 10×10 435
330 6.3×7.7 105 8×10 305 8×10 340 10×10 360
470 8×10 330 10×10 340 10×10 470 Ripple current (mA rms) at 105°
C, 120Hz
1000 10×10 475 Case size ØD×L (mm)

Coefficient 0.70 1.00 1.17 1.36 1.50
58
JC Chip type, Higher Capacitance Range

WV≦100V
・Chip type higher capacitance in large case sizes

Operating temperature range WV≦100 : -55 ~ +105°C WV≧160 : -40 ~ +105° C
Capacitance tolerance ±20% at 120Hz, 20°C
Dissipation factor max. WV 4 6.3 10 16 25 35 50 63 100 160 200 250 400 450
(at 120Hz, 20°C) tanδ 0.37 0.28 0.24 0.20 0.16 0.13 0.12 0.10 0.10 0.15 0.15 0.15 0.20 0.20
WV 4 6.3 10 16 25 ~ 50 63 ~ 100 160 ~ 250 400 ~ 450

Low temperature characteristics Z-25°
C/Z+20°
C 6 3 3 2 2 3 3 6
(Impedance ratio at 120Hz) Z-40°
C/Z+20°
C 12 8 5 4 3 4 6 10
Z-55°
C/Z+20°
C 12 8 5 4 3 4 - -

C) The measurement shall be performed at 20° C by the KS C IEC 60384 - 4
C
CHIP TYPES
Unit : mm
● DRAWING -Series code of JC is “J”
(Ø6.3,Ø8×6.2)
ØD×L A B C E R
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8
J
8×10 2.9 8.3 8.3 3.1 0.8~1.1

10×10 3.2 10.3 10.3 4.5 0.8~1.1
12.5×13.5 4.6 12.8 12.8 4.5 0.8~1.4
※Voltage mark for
6.3V is 6
(Ø8×10, Ø10×10)
J
(Ø12.5)
59
JC series

μF WV 4 6.3 10 16 25 35 50
10 6.3×5.8 30
22 6.3×5.8 38 6.3×5.8 42 8×6.2 67
33 6.3×5.8 40 6.3×5.8 48 8×6.2 76 8×10 133
47 6.3×5.8 46 6.3×5.8 50 8×6.2 79 8×10 124 10×10 180
100 6.3×5.8 60 6.3×5.8 60 6.3×5.8 60 8×10 148 8×10 181 10×10 304 10×10 310
220 8×10 161 8×10 173 10×10 330 10×10 351 10×10 450 12.5×13.5 480
330 8×10 288 10×10 318 10×10 441 10×10 372 12.5×13.5 500
470 10×10 340 10×10 351 10×10 489 10×10 450 12.5×13.5 600
680 10×10 408 10×10 392 12.5×13.5 500 12.5×13.5 500
1000 10×10 495 10×10 550 12.5×13.5 600
1500 10×10 560 12.5×13.5 650
2200 12.5×13.5 730
μF WV 63 100 160 200 250 400 450
3.3 10×10 30 12.5×13.5 30 12.5×13.5 40
4.7 10×10 45 12.5×13.5 65
10 8×6.2 32 10×10 45 12.5×13.5 75
22 8×10 60 8×10 90 12.5×13.5 85 12.5×13.5 85
33 8×10 110 10×10 120 12.5×13.5 95 Ripple current (mA r ms) at 105°
C, 120Hz
47 10×10 130 12.5×13.5 250 Case size ØD X L (mm)
68 10×10 160 12.5×13.5 300
100 12.5×13.5 270

Coefficient 0.70 1.00 1.17 1.36 1.50
60
JH Chip type, High Ripple Current

WV≦100V
・High Ripple current Compared with JC series

Operating temperature range WV≦100 : -55 ~ +105°C WV≧160 : -40 ~ +105° C
Capacitance tolerance ±20% at 120Hz, 20°C
Dissipation factor max. WV 6.3 10 16 25 35 50 63 100 160 200 250 400 450
(at 120Hz, 20°C) tanδ 0.28 0.24 0.20 0.16 0.13 0.12 0.10 0.10 0.15 0.15 0.15 0.20 0.20
WV 6.3 10 16 25 ~ 50 63 ~ 100 160 ~ 250 400 ~ 450

C/Z+20°
C 3 3 2 2 3 3 6
C/Z+20°
C - - - - - 6 10
Z-55°
C/Z+20°
C 8 5 4 3 4 - -

C
CHIP TYPES
Unit : mm
● DRAWING -Series code of JH is “G”
(Ø6.3,Ø8×6.2)
ØD×L A B C E R
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8
G
8×10 2.9 8.3 8.3 3.1 0.8~1.1

10×10 3.2 10.3 10.3 4.5 0.8~1.1
12.5×13.5 4.6 12.8 12.8 4.5 0.8~1.4
※Voltage mark for
6.3V is 6
(Ø8×10, Ø10×10)
G
(Ø12.5)
61
JH series

μF WV 6.3 10 16 25 35
10
22 6.3×5.8 57 6.3×5.8 63
33 6.3×5.8 60 6.3×5.8 72 8×6.2 114
47 6.3×5.8 69 6.3×5.8 75 8×6.2 120 8×10 186
100 6.3×5.8 90 6.3×5.8 90 8×10 222 8×10 270 10×10 456
220 8×10 242 8×10 260 10×10 495 10×10 525 10×10 675
330 8×10 432 10×10 477 10×10 660 10×10 558 12.5×13.5 750
470 10×10 510 10×10 527 10×10 735 10×10 675 12.5×13.5 900
680 10×10 612 10×10 588 12.5×13.5 750 12.5×13.5 750
1000 10×10 743 10×10 825 12.5×13.5 900
1500 10×10 840 12.5×13.5 975 Ripple current (mA r ms) at 105°
C, 120Hz
2200 12.5×13.5 1095 Case size ØD X L (mm)
μF WV 50 63 100
10 6.3×5.8 45 8×6.2 48
22 8×6.2 100 8×10 90 8×10 135
33 8×10 200 8×10 165 10×10 180
47 10×10 270 10×10 195 12.5×13.5 375
68 10×10 315 10×10 240 12.5×13.5 450
100 10×10 465 12.5×13.5 405
220 12.5×13.5 720
μF WV 160 200 250 400 450

3.3 10×10 45 12.5×13.5 45 12.5×13.5 60
4.7 10×10 65 12.5×13.5 95
10 10×10 65 12.5×13.5 110
22 12.5×13.5 125 12.5×13.5 125
33 12.5×13.5 140
47
C, 120Hz
68 Case size ØD X L (mm)
100

Coefficient 0.70 1.00 1.17 1.36 1.50
62
JM Chip type, Long Life

WV≦100V
・Long Life Compared with JC series
C
C
Dissipation factor max. WV 6.3 10 16 25 35 50 63 100 160 200 250 400 450
(at 120Hz, 20°C) tanδ 0.32 0.28 0.21 0.21 0.18 0.18 0.12 0.12 0.15 0.15 0.15 0.20 0.20
Low temperature characteristics WV 6.3 10 16 25 ~ 50 63 ~ 100 160 ~ 250 400 ~ 450

C/Z+20°
C 8 8 6 4 3 3 6

C
CHIP TYPES
Unit : mm
● DRAWING -Series code of JM is “Q”
(Ø4, Ø5) ＋ Positive ØD×L W A B C E R

Capacitance Series Code Plastic plateform
4×5.3 4.8 4.3 4.3 1.0 0.5~0.8
0.4 max.
0.3 max. C±0.2 5×5.3 5.8 5.3 5.3 1.4 0.5~0.8

6.3×5.3 2.4 6.6 6.6 2.2 0.5~0.8
＋
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
ØD±0.5
W±0.2
Lot No.
E±0.2
6Q
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8

B±0.2
47
※Voltage
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8
－ 8×10 2.9 8.3 8.3 3.1 0.8~1.1
10×10 3.2 10.3 10.3 4.5 0.8~1.1
※Voltage mark for － Negative 12.5×13.5 4.6 12.8 12.8 4.5 0.8~1.4
5.3±0.2 R
6.3V is 6
(Ø6.3,Ø8×6.2) (Ø12.5)
Q
(Ø8×10, Ø10×10)
Q
63
JM series

μF WV 6.3 10 16 25 35
10 4×5.3 10 4×5.3 15 4×5.3 19 5×5.3 24 6.3×5.3 26
22 4×5.3 25 5×5.3 30 5×5.3 33 6.3×5.3 38 6.3×5.8 42
33 5×5.3 35 5×5.3 38 6.3×5.3 42 6.3×5.8 48 8×6.2 76
47 5×5.3 42 6.3×5.3 52 6.3×5.8 60 8×6.2 79 8×10 124
100 6.3×5.8 60 6.3×5.8 60 8×10 148 8×10 181 10×10 310
220 8×10 161 8×10 173 10×10 330 10×10 351 10×10 480
330 8×10 288 10×10 318 10×10 441 10×10 372 12.5×13.5 500
470 10×10 340 10×10 351 10×10 489 10×10 450 12.5×13.5 600
680 10×10 408 10×10 392 12.5×13.5 500 12.5×13.5 500
1000 10×10 495 10×10 550 12.5×13.5 600
1500 10×10 560 12.5×13.5 650 Ripple current (mA r ms) at 105°
C, 120Hz
2200 12.5×13.5 730 Case size ØD X L (mm)
μF WV 50 63 100
10 6.3×5.8 30 8×6.2 32
22 8×6.2 67 8×10 60 8×10 90
33 8×10 133 8×10 110 10×10 120
47 10×10 180 10×10 130 12.5×13.5 250
68 10×10 200 10×10 160 12.5×13.5 300
100 10×10 310 12.5×13.5 270
220 12.5×13.5 480
μF WV 160 200 250 400 450

3.3 10×10 30 12.5×13.5 30 12.5×13.5 40
4.7 10×10 45 12.5×13.5 65
10 10×10 45 12.5×13.5 75
22 12.5×13.5 85 12.5×13.5 85
33 12.5×13.5 95
47
C, 120Hz
68 Case size ØD X L (mm)
100

Coefficient 0.70 1.00 1.17 1.36 1.50
64
CA Chip type, Long Life

Series Long Life Solvent Proof
・Chip type, long life capacitance in large case sizes

・Chip type with load life of 5000 hours at 105°C
(at 120Hz, 20°C) tanδ 0.28 0.24 0.2 0.16 0.13 0.12
WV 6.3 10 16 25 35 50
Z-25°
C/Z+20°
C 2 2 2 3 3 3
Z-55°
C/Z+20°
C 4 4 3 3 3 3

C
CHIP TYPES
Unit : mm
● DRAWING
-Series code of CA is “A”
Please refer to drawing for CK Series in page 69 for detail drawing.

μF WV 6.3 10 16 25 35 50
10 6.3×5.8 30
22 6.3×5.8 38 6.3×5.8 42 6.3×7.7 120
33 6.3×5.8 40 6.3×5.8 48 6.3×7.7 57 8×10 140
47 6.3×5.8 46 6.3×5.8 50 6.3×7.7 63 8×10 92 8×10 170
100 6.3×5.8 60 6.3×7.7 81 6.3×7.7 81 8×10 116 10×10 151 10×10 310
220 6.3×7.7 101 8×10 141 10×10 216 10×10 216 10×10 216
330 8×10 160 10×10 238 10×10 238 10×10 238 Ripple current (mA rms) at 105°
C, 120Hz
470 10×10 254 10×10 254 10×10 254 Case size ØD×L (mm)
1000 10×10 313

Coefficient 0.70 1.00 1.17 1.36 1.50
65
CB Chip type,Long Life

・Chip type with load life 5000 hours at 105°C

・Chip type with 5.5mmL Height
Dissipation factor max. WV 4 6.3 10 16 25 35 50
(at 120Hz, 20°C) tanδ 0.24 0.22 0.19 0.16 0.14 0.12 0.11
WV 4 6.3 10 16 25 ~ 50
Z-25°
C/Z+20°
C 6 4 3 2 2
Z-55°
C/Z+20°
C 12 10 7 5 3

(after application of the rated tanδ Less than 300% of the specified value
voltage for 5000 hours at 105° C) Leakage current Less than specified value
C
Unit : mm
-Series code of CB is “B”

WV 4 6.3 10 16 25 35 50
μF
0.1 4×5.3 2
0.22 4×5.3 3
0.33 4×5.3 4
0.47 4×5.3 5
1.0 4×5.3 7
2.2 4×5.3 11
3.3 4×5.3 14
4.7 4×5.3 14 4×5.3 15 5×5.3 19
6.8 4×5.3 17 5×5.3 21 6.3×5.3 26
10 4×5.3 19 5×5.3 24 5×5.3 26 6.3×5.3 33
15 4×5.3 22 5×5.3 28 5×5.3 31 6.3×5.3 37 6.3×5.3 40
22 4×5.3 24 4×5.3 25 5×5.3 30 5×5.3 33 6.3×5.3 42 6.3×5.3 45
33 5×5.3 33 5×5.3 35 5×5.3 38 6.3×5.3 48
47 5×5.3 40 5×5.3 42 6.3×5.3 52 6.3×5.3 57 Ripple current (mA rms) at 105°
C, 120Hz
68 5×5.3 48 6.3×5.3 55 6.3×5.3 63 Case size ØD×L(mm)
100 5×5.3 55 6.3×5.3 67 6.3×5.3 72

Coefficient 0.70 1.00 1.17 1.36 1.50
66
JL Chip type, Long Life

・Chip type, long life capacitance in large case size

・For ECU
・Application to automatic insertion machine using carrier tape
Leakage current I = 0.03CV or 4μA whichever is greater (after 2 minutes)
Capacitance tolerance ±20% (20° C, 120Hz)
Dissipation factor max. Rated Voltage(V) 10 16 25 35 50
(at 120Hz, 20°C) tanδ 0.32 0.24 0.21 0.18 0.18
WV 10 16 25 35 50
Z-25°
C/Z+20°
C 6 4 3 2 2
Z-40°
C/Z+20°
C 12 10 8 6 6

(after application of the rated Capacitance change Within ±30% of the initial value
C)
C
CHIP TYPES
Resistance to soldering heat
Capacitance change Within ±30% of the initial value
tanδ Less than 300% of the specified value
Unit : mm
-Series code of JL is “P”

μF WV 10 16 25 35 50
33 8×10 75
47 8×10 90 8×10 90
100 8×10 270 8×10 163 10×10 132 10×10 167
220 8×10 270 8×10 270 10×10 200 10×10 249
330 8×10 270 10×10 315 10×10 304
470 10×10 315 10×10 315
Ripple current (mA rms) at 105°

C, 120Hz
Case size ØD×L(mm)

Coefficient 0.70 1.00 1.17 1.36 1.50
67
ZC Height 5.5mmL, Low Impedance

Series Low Impedance Solvent Proof
・Chip type, low impedance temperature range up to 105° C

Dissipation factor max. WV 6.3 10 16 25 35
(at 120Hz, 20°C) tanδ 0.22 0.19 0.16 0.14 0.12
WV 6.3 10 16 25 35
Z-25°
C/Z+20°
C 2 2 2 2 3
Z-55°
C/Z+20°
C 4 4 3 3 3


C) After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.
C
Unit : mm
-Series code of ZC is “Z”

μF WV 6.3 10 16 25 35
1.0 4×5.3 5.0 50
1.5 4×5.3 5.0 50
2.2 4×5.3 5.0 50
3.3 4×5.3 5.0 50
4.7 4×5.3 5.0 50 4×5.3 5.0 50
6.8 4×5.3 5.0 50 5×5.3 2.6 80
10 4×5.3 5.0 50 5×5.3 2.6 80 5×5.3 2.6 80
15 5×5.3 2.6 80 6.3×5.3 1.3 75 6.3×5.3 1.3 115
22 4×5.3 5.0 50 5×5.3 2.6 80 5×5.3 2.6 80 6.3×5.3 1.3 115 6.3×5.3 1.3 115
33 5×5.3 2.6 80 5×5.3 2.6 80 6.3×5.3 1.3 115 6.3×5.3 1.3 115
47 5×5.3 2.6 80 6.3×5.3 1.3 115 6.3×5.3 1.3 115 Ripple current (mA rms) at 105°
C, 100kHz
68 6.3×5.3 1.3 115 6.3×5.3 1.3 115 Impedance (Ω) at 20°
C, 100kHz
100 6.3×5.3 1.3 115 Case size ØD×L(mm)

Coefficient 0.35 0.5 0.64 0.83 1.00
68
CK Chip type, Low Impedance, High CV


Dissipation factor max. WV 6.3 10 16 25 35 50 63 80 100
(at 120Hz, 20°C) tanδ 0.24 0.19 0.16 0.14 0.12 0.12 0.10 0.10 0.10
WV 6.3 10 16 25 35 50 63~100
Z-25°
C/Z+20°
C 2 2 2 2 2 2 3
Z-55°
C/Z+20°
C 3 3 3 3 3 3 4

C)
C
CHIP TYPES
Unit : mm
● DRAWING -Series code of CK is “K”
(Ø6.3,Ø8×6.2)
ØD×L A B C E R
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8
K
8×10 2.9 8.3 8.3 3.1 0.8~1.1

10×10 3.2 10.3 10.3 4.5 0.8~1.1
12.5×13.5 4.6 12.8 12.8 4.5 0.8~1.4
※Voltage mark for
6.3V is 6
(Ø8×10, Ø10×10)
K
(Ø12.5×13.5)
69
CK series

μF WV 6.3 10 16 25 35 50
10 6.3×5.8 1.0 165
15 6.3×5.8 1.0 165
22 6.3×5.8 1.0 165
6.3×7.7 0.68 280

33 6.3×5.8 0.44 230 6.3×5.8 0.44 230 6.3×5.8 0.44 230
8×6.2 0.63 300
6.3×7.7 0.68 280

47 6.3×5.8 0.44 230 6.3×5.8 0.44 230 6.3×5.8 0.44 230 6.3×5.8 0.44 230
8×6.2 0.63 300
6.3×7.7 0.34 280

68 6.3×5.8 0.44 230 6.3×5.8 0.44 230 6.3×5.8 0.44 230 6.3×5.8 0.44 230 8×10 0.34 450
8×6.2 0.26 300
6.3×7.7 0.34 280

100 6.3×5.8 0.44 230 6.3×5.8 0.44 230 6.3×5.8 0.44 230 8×10 0.17 450 10×10 0.18 670
8×6.2 0.26 300
6.3×7.7 0.34 280

150 6.3×5.8 0.44 230 6.3×5.8 0.44 230 8×10 0.17 450 8×10 0.17 450
8×6.2 0.26 300
6.3×7.7 0.34 280 6.3×7.7 0.34 280

220 6.3×5.8 0.44 230 8×10 0.17 450 10×10 0.09 670
8×6.2 0.26 300 8×6.2 0.26 300
6.3×7.7 0.34 280

330 8×10 0.17 450 8×10 0.17 450 10×10 0.15 670
8×6.2 0.26 300
470 8×10 0.17 450 8×10 0.17 450 10×10 0.09 670
680 8×10 0.17 450 10×10 0.09 670
1000 10×10 0.09 670
1500 10×10 0.09 670
μF WV 63 80 100
10 6.3×5.8 2.8 80 6.3×7.7 2.4 60
22 6.3×7.7 2.1 120 8×10 1.3 130 8×10 1.3 130
33 8×10 0.9 250 8×10 1.3 130 10×10 1.2 200
47 8×10 0.9 250 10×10 1.2 200 12.5×13.5 0.8 500
68 10×10 0.5 400 12.5×13.5 0.8 500 12.5×13.5 0.8 500
100 10×10 0.5 400 12.5×13.5 0.8 500
150 12.5×13.5 0.32 800 12.5×13.5 0.8 500
220 12.5×13.5 0.32 800
C, 100kHz
Impedance (Ω) at 20° C, 100kHz

Coefficient 0.35 0.5 0.64 0.83 1.00
70
CD Chip type, Extremely Low Impedance


(at 120Hz, 20°C) tanδ 0.24 0.19 0.16 0.14 0.12 0.12
WV 6.3 10 16 25 35 50
Z-25°
C/Z+20°
C 2 2 2 2 2 2
Z-55°
C/Z+20°
C 3 3 3 3 3 3

C)
C
CHIP TYPES
Unit : mm
● DRAWING
-Series code of CD is “D”
(Ø6.3×5.8, 7.7, Ø8×6.2)
ØD A B C E R
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8
D
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8

8×10 2.9 8.3 8.3 3.1 0.8~1.1
10×10 3.2 10.3 10.3 4.5 0.8~1.1
※Voltage mark for
6.3V is 6
(Ø8×10, Ø10×10)
D
71
CD series

μF WV 6.3 10 16 25 35 50
10 6.3×5.8 0.86 170
15 6.3×5.8 0.86 170
22 6.3×5.8 0.86 170
6.3×7.7 0.66 280

33 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×5.8 0.39 240
8×6.2 0.63 300
6.3×7.7 0.66 280

47 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×5.8 0.39 240
8×6.2 0.63 300
68 6.3×5.8 0.36 240 6.3×5.8 0.36 240 6.3×5.8 0.36 240 6.3×5.8 0.36 240 6.3×7.7 0.32 290 8×10 0.32 350
6.3×7.7 0.32 290

100 6.3×5.8 0.36 240 6.3×5.8 0.36 240 6.3×5.8 0.36 240 8×10 0.16 600 10×10 0.16 700
8×6.2 0.26 300
150 6.3×5.8 0.36 240 6.3×5.8 0.36 240 6.3×7.7 0.32 290 8×10 0.16 600 8×10 0.16 600
6.3×7.7 0.32 290 6.3×7.7 0.32 290

220 6.3×5.8 0.36 240 8×10 0.16 600 10×10 0.08 850
8×6.2 0.26 300 8×6.2 0.26 300
6.3×7.7 0.32 290

330 8×10 0.16 600 8×10 0.16 600 10×10 0.10 850
8×6.2 0.26 300
470 8×10 0.16 600 8×10 0.16 600 10×10 0.08 850 Ripple current (mA r ms) at 105°
C, 100kHz
680 8×10 0.16 600 10×10 0.08 850 Impedance (Ω) at 20°
C, 100kHz
1000 10×10 0.08 850
1500 10×10 0.08 850

Coefficient 0.35 0.5 0.64 0.83 1.00
72

Upgrade
CM Chip type, Extremely Low Impedance

Long Life Series Low Impedance Solvent Proof

Dissipation factor max. WV 6.3 10 16 25 35 50 63 ~ 100
(at 120Hz, 20°C) tanδ 0.26 0.19 0.16 0.14 0.13 0.12 0.10
WV 6.3 10 16 25 35 50 ~ 100
Z-25°
C/Z+20°
C 2 2 2 2 2 2
Z-55°
C/Z+20°
C 4 4 4 3 3 3

(after application of the rated tanδ Less than 250% of specified value
voltage for 5000 hours at 105° C) ØD ØD ≦ 6.3, Ø8×6.2mmL ØD ≧ 8
Life time 3000 hours 5000 hours
C
CHIP TYPES
Unit : mm
● DRAWING
-Series code of CM is “M”
(Ø6.3,Ø8×6.2)
ØD×L A B C E R
6.3×5.8 2.4 6.6 6.6 2.2 0.5~0.8
6.3×7.7 2.4 6.6 6.6 2.2 0.5~0.8
8×6.2 3.3 8.3 8.3 2.3 0.5~0.8
J
8×10 2.9 8.3 8.3 3.1 0.8~1.1

10×10 3.2 10.3 10.3 4.5 0.8~1.1
12.5×13.5 4.6 12.8 12.8 4.5 0.8~1.4
※Voltage mark for
6.3V is 6
(Ø8×10, Ø10×10)
J
(Ø12.5)
73
CM series

μF WV 6.3 10 16 25 35 50
10 6.3×5.8 0.86 170
15 6.3×5.8 0.86 170
22 6.3×5.8 0.86 170
6.3×7.7 0.66 280

33 6.3×5.8 0.43 240 6.3×5.8 0.43 240 6.3×5.8 0.43 240
8×6.2 0.63 300
6.3×7.7 0.66 280

47 6.3×5.8 0.43 240 6.3×5.8 0.43 240 6.3×5.8 0.43 240 6.3×5.8 0.43 240
8×6.2 0.63 300
68 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×7.7 0.32 290 8×10 0.32 350
6.3×7.7 0.32 290

100 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×5.8 0.39 240 8×10 0.16 600 10×10 0.16 700
8×6.2 0.26 300
150 6.3×5.8 0.39 240 6.3×5.8 0.39 240 6.3×7.7 0.32 290 8×10 0.16 600 8×10 0.16 600
6.3×7.7 0.36 290 6.3×7.7 0.32 290

220 6.3×5.8 0.39 240 8×10 0.16 600 10×10 0.08 850
8×6.2 0.26 300 8×6.2 0.26 300
6.3×7.7 0.32 290

330 8×10 0.16 600 8×10 0.16 600 10×10 0.1 850
8×6.2 0.26 300
470 8×10 0.16 600 8×10 0.16 600 10×10 0.08 850 Ripple current (mA r ms) at 105°
C, 100kHz
680 8×10 0.16 600 10×10 0.08 850 Impedance (Ω) at 20°
C, 100kHz
1000 10×10 0.08 850
μF WV 63 80 100
10 6.3×7.7 2 80 6.3×7.7 2.4 60 8×10 2 100
22 6.3×7.7 1.2 120 8×10 1.3 130 8×10 2 140
33 8×10 0.65 250 8×10 1.3 130 10×10 0.8 330
47 8×10 0.65 250 10×10 0.7 200 12.5×13.5 0.45 500
68 10×10 0.35 400 12.5×13.5 0.32 500 12.5×13.5 0.45 500
100 10×10 0.35 400 12.5×13.5 0.32 500
150 12.5×13.5 0.16 800 12.5×13.5 0.32 500
220 12.5×13.5 0.16 800

Coefficient 0.35 0.5 0.64 0.83 1.00
74
UC Chip type, High Reliability

WV≦100V
・Chip type, high temperature range, for 125°C use

C
C
Dissipation factor max. WV 10 16 25 35~63 80~100 160~200 250~400
(at 120Hz, 20°C) tanδ 0.32 0.24 0.21 0.18 0.12 0.2 0.24
WV 10 16 25 35~63 80~100 160~200 250~400

Z-25°
C/Z+20°
C 8 6 4 4 3 3 6
Z-40°
C/Z+20°
C 12 8 6 4 4 6 10

C)
C
CHIP TYPES
Unit : mm
-Series code of UC is “U”

μF WV 10 16 25 35 50 63
10 8×6.2 65 8×6.2 40
22 8×6.2 65 8×10 67
33 8×6.2 65 8×10 125 8×10 67
47 8×6.2 65 8×10 125 10×10 200 10×10 115
68 8×6.2 65 8×6.2 65 10×10 200 12.5×13.5 525 12.5×13.5 335
100 8×6.2 65 8×10 125 8×10 125 10×10 200 12.5×13.5 525 12.5×13.5 335
220 8×10 125 10×10 200 10×10 200 12.5×13.5 525
330 10×10 200 10×10 200 12.5×13.5 525
470 10×10 200 12.5×13.5 525 Ripple current (mA rms) at 125°
C, 120Hz
1000 12.5×13.5 525 Case size ØD×L(mm)
μF WV 80 100 160 200 250 400

3.3 12.5×13.5 30
4.7 12.5×13.5 45 12.5×13.5 30
10 8×10 45 8×10 45 10×10 45 10×10 45 12.5×13.5 85
22 8×10 45 10×10 80 12.5×13.5 85 12.5×13.5 85
33 10×10 80 10×10 80
47 12.5×13.5 300 Ripple current (mA rms) at 125°
C, 120Hz
10×10 80
68 12.5×13.5 300 12.5×13.5 300

Coefficient 0.70 1.00 1.17 1.36 1.50
75
UR Chip type, High Reliability


・Lower ESR than UC series
Leakage current max. I = 0.01CV or 3μA whichever is greater (after 2 minutes)
WV 10 16 25 35 50
Dissipation factor max.
tanδ(Max.) 0.24 0.20 0.16 0.14 0.14
WV 10 16 25 35 50
emperature characteristics
C/Z+20°
C 3 2 2 2 2
Z-40°
C/Z+20°
C 4 3 3 3 3

C
Unit : mm
-Series code of UR is “R”

μF WV 10 16 25 35 50
33 8×10 0.7 192
47 8×10 0.3 264 10×10 0.5 330
100 8×10 0.3 264 8×10 0.3 264 8×10 0.3 264 10×10 0.5 330
220 8×10 0.3 264 8×10 0.3 355 8×10 0.3 355 10×10 0.2 400
330 8×10 0.3 355 10×10 0.2 400 10×10 0.2 400
470 10×10 0.2 400
C, 100kHz
ESR (Ω) at 20° C, 100kHz

Coefficient 0.35 0.50 0.64 0.83 1.00
76
CF Chip type, High Temperature, Long Life,


・For ECU
・Application to automatic insertion machine using carrier
Leakage current I = 0.03CV or 4μ
(at 120Hz, 20°C) tanδ 0.32 0.24 0.21 0.18 0.18
WV 10 16 25 35 50
C/Z+20°
C 8 6 4 4 4
Z-40°
C/Z+20°
C 12 11 8 6 6

(after application of the rated tanδ Less than 300% of the specified value
ØD Ø8×6.2mmL Ø8×10mmL ØD ≧ 10
Life time 2000 hours 3000 hours 5000 hours
CHIP TYPES
C
Unit : mm
-Series code of CF is “H”

μF WV 10 16 25 35 50
22 8×6.2 28
33 8×6.2 41 8×10 75
47 10×10 90 10×10 90
68 8×6.2 50 8×6.2 45 10×10 105 12.5×13.5 132
100 8×6.2 48 8×10 66 10×10 163 10×10 132 12.5×13.5 167
220 8×10 90 10×10 163 10×10 200 12.5×13.5 249
330 10×10 125 10×10 200 12.5×13.5 304
C, 120Hz
1000 12.5×13.5 405 Case size ØD×L(mm)

Coefficient 0.70 1.00 1.17 1.36 1.50
77
CT Chip type, High Temperature, Low Imp.,

・Chip type, Low Impedance temperature range up to 130° C use

・For ECU
・Application to automatic insertion machine using carrier tape
Capacitance tolerance ±20% ( 20° C, 120Hz)
(at 120Hz, 20°C) tanδ 0.32 0.24 0.21 0.18 0.18
WV 10 16 25 35 50
Z-25°
C/Z+20°
C 8 6 4 4 4
Z-40°
C/Z+20°
C 12 10 8 6 6
Load life Leakage Current Less than specified value

(after application of the rated Capacitance Change Within ±30% of initial value
C
Resistance to soldering heat Leakage Current Less than specified value
Capacitance Change Within ±10% of initial value
Unit : mm
-Series code of CT is “C”

μF WV 10 16 25 35 50
33 8×10 0.6 270
47 8×10 0.6 270 10×10 0.5 315
68 8×10 0.6 270 8×10 0.6 270 10×10 0.5 270 10×10 0.5 315
100 8×10 0.6 270 8×10 0.6 270 8×10 0.6 270 10×10 0.5 315 12.5×13.5 0.4 345
220 8×10 0.6 270 8×10 0.6 270 10×10 0.5 315 12.5×13.5 0.4 345
330 10×10 0.5 315 10×10 0.5 315 12.5×13.5 0.4 345
470 10×10 0.5 315 12.5×13.5 0.4 345 Ripple current (mA rms) at 130°
C, 100kHz
Impedance (Ω) at 20°

C, 100kHz

Coefficient 0.35 0.5 0.64 0.83 1.00
78
CW Chip type, High Reliability


Leakage current I = 0.03CV or 4μ
Dissipation factor max. WV 10 16 25 35 50
(at 120Hz, 20°C) tanδ 0.30 0.20 0.16 0.14 0.14
WV 10 16 25 35 50
C/Z+20°
C 8 6 4 4 4
Z-40°
C/Z+20°
C 12 10 8 6 6

C
CHIP TYPES
Unit : mm
-Series code of CW is “W”

WV 10 16 25 35 50
μF
33 10×10 75
47 10×10 90 10×10 90
68 10×10 105 12.5×13.5 132
100 10×10 160 10×10 132 12.5×13.5 167
220 10×10 163 10×10 200 12.5×13.5 249
330 10×10 183 10×10 200 12.5×13.5 304
C, 120Hz
1000 12.5×13.5 405 Case size ØD×L(mm)

Coefficient 0.70 1.00 1.17 1.36 1.50
79
NC Chip type, Non-polarized

Series Non-polarized Solvent Proof
・Chip type with 5.5mmL height

・Applicable to automatic mounting machine using carrier tape
(at 120Hz, 20°C) tanδ 0.24 0.20 0.17 0.17 0.15 0.15
WV 6.3 10 16 25 35 50
C/Z+20°
C 4 3 2 2 2 2
Z-40°
C/Z+20°
C 8 6 4 4 3 3

Load life
Test method Polarity reverse each 250 hours
Shelf life (at 85°
C
Unit : mm
● DRAWING
-Series code of NC is “N”
Plastic plateform
Capacitance
0.4 max.
0.3 max. C±0.2

Series Code
ØD W B C E
ØD±0.5
4 4.8 4.3 4.3 1.0

W±0.2
E±0.2
B±0.2
Lot No.
6N
※Voltage
47
5 5.8 5.3 5.3 1.4

6.3 7.1 6.6 6.6 2.2
※Voltage mark for 5.3±0.2 0.5~0.8

6.3V is 6

μF WV 6.3 10 16 25 35 50
0.1 4×5.3 1.0
0.22 4×5.3 2.0
0.33 4×5.3 2.8
0.47 4×5.3 4.0
1.0 4×5.3 8.4
2.2 4×5.3 8.4 5×5.3 13
3.3 5×5.3 12 5×5.3 16 5×5.3 17
4.7 4×5.3 12 5×5.3 16 5×5.3 18 6.3×5.3 20
10 4×5.3 17 5×5.3 23 6.3×5.3 27 6.3×5.3 29
22 5×5.3 28 6.3×5.3 33 6.3×5.3 37
33 6.3×5.3 37 6.3×5.3 41 6.3×5.3 49 Ripple current (mA rms) at 85°
C, 120Hz
47 6.3×5.3 45 Case size ØD X L (mm)
80
CN Height 5.5mmL, 105°

Series
C Non-polarized
Non-polarized Solvent Proof
・Chip type, Non-polarized, Wide temperature 105° C

・Chip type with 5.5mmL height
Operating temperature range WV≦25 : -55 ~ +105° C WV≧35 : -40 ~ +105° C
(at 120Hz, 20°C) tanδ 0.32 0.26 0.24 0.20 0.18 0.18
WV 6.3 10 16 25 35 50
C/Z+20°
C 4 3 2 2 2 2
C/Z+20°
C - - - - 4 4
Z-55°
C/Z+20°
C 8 5 4 3 - -

Load life
C)
C
CHIP TYPES
Unit : mm
-Series code of CN is “C”

μF WV 6.3 10 16 25 35 50
0.1 4×5.3 1.3
0.22 4×5.3 2.3
0.33 4×5.3 2.8
0.47 4×5.3 4.0
1.0 4×5.3 8.4
2.2 4×5.3 8.4 5×5.3 13
3.3 5×5.3 12 5×5.3 16 5×5.3 17
4.7 4×5.3 12 5×5.3 16 5×5.3 18 6.3×5.3 20
10 4×5.3 17 5×5.3 23 6.3×5.3 27 6.3×5.3 29
22 5×5.3 28 6.3×5.3 33 6.3×5.3 37
33 6.3×5.3 37 6.3×5.3 41 6.3×5.3 49
47 6.3×5.3 45
C, 120Hz
Case size ØD×L (mm)
81
82
4 MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
PART NUMBER SYSTEM
Part Number System
Series Name Rated Voltage Capacitance Cap. Tol. Case Diameter Case Height Lead Taping Internal Control
Forming and Cutting Code
Series Name Case Height

See page 6 ~ 7. ex) 5mm 005
11mm 011
12.5mm 12M
Rated Working Voltage 20mm 020
31.5mm 31M
WV 2.5 4 6.3 10 16 20 25 35.5mm 35M
Code 0E 0G 0J 1A 1C 1D 1E
WV 35 40 50 63 80 100 160
Code 1V 1G 1H 1J 1K 2A 2C Lead Taping, Forming and Cutting

See pages 86 ~ 88
WV 200 250 315 350 400 450 500
Code 2D 2E 2F 2V 2G 2W 2H
Capacitance
ex) 0.47 F 474
4.7 F 475
47 F 476
470 F 477
4700 F 478
47000 F 479
Capacitance Tolerance
Tolerance (%) 10 20 20 30 50
Code K M V Q T
Case Diameter
ex) 3 03 12.5 12
4 04 16 16
5 05 18 18
6.3 6L 22 22
8 08
10 10
84
PACKING
BULK PACKING QUANTITY(pcs) / BOX
SIZE BULK (QUANTITY)
D L (mm) V-Bag INNER BOX MIDDLE BOX
3 5 500 12000 48000

4 5, 7 500 10000 40000
5 5, 7, 9, 11 500 7000 28000
6.3 5, 7, 9, 11 500 6000 24000
5 500 5000 20000
8
9, 11.5 300 3600 14400
9, 12.5 200 2400 9600
10 16 200 2000 8000
20, 25 200 1600 6400
16 100 1200 4800
12.5 20 100 1000 4000
25 100 900 3600
16 100 800 3200
20 50 600 2400
16
25 50 500 2000
31.5, 35.5 50 400 1600
16 50 600 2400
20 50 500 2000
18
20, 25, 31.5 50 400 1600
35.5 50 300 1200
CUTTING PACKING QUANTITY(pcs) / BOX
SIZE CUTTING (QUANTITY)
D L (mm) V-Bag INNER BOX MIDDLE BOX
4 5, 7 500 9000 36000

5 5, 7, 9, 11 500 7000 28000
6.3 5, 7, 9, 11 500 6000 24000
5 500 5000 20000
8
9, 11.5 300 3600 14400
9 1000 16000
12.5 800 12800
MINIATURE TYPES
16 600 9600
10 20 500 8000
25 400 6400
30 400 6400
40 900 1800
16 400 6400
20 300 4800
12.5
25 250 4000
40 600 1200
16 400 1200
20 400 1200
16 25, 31.5 400 1200
35.5 400 1200
40 400 1200
16 300 900
20 300 900
18 25 300 900
31.5, 35.5 300 900
40 300 900
20 41 240 720
35.5 200 600
22
40 200 600
( ) is for oversea
85
Ammo
TAPING
Lead Taping Capacitors for Automatic Insertion
DRAWING DRAWING
P2 P P2 P
h h
L L
P1 F P1 F
H H R2
H0 W2 H0 W2
A W1 A W1
W0 Wo W t
W t
P0 d D0 P0 d D0
DIMENSIONS Unit : mm
Applicable Drawing No. ( )
Description Symbol Tolerance 3 4 5 6.3 8 4 5 6.3 8
Case Height L *Note 5 5, 7 5 7~11 5 7~11 5 5, 7 5 7~11 5 7~11 5 9, 11.5

Lead Dia. d 0.05 0.4 0.45 0.45 0.5 0.45 0.5 0.45 0.45 0.45 0.5 0.45 0.5 0.45 0.6
Body Pitch P 1.0 12.7 12.7 12.7 12.7 12.7 12.7
Feeding Hole Pitch P0 0.2 12.7 12.7 12.7 12.7 12.7 12.7
Feeding Hole Alignment P1 0.7 5.1 5.1 5.1 3.85 3.85 3.85
Feeding Hole Alignment P2 1.0 6.35 6.35 6.35 6.35 6.35 6.35
0.6
Lead Center Spacing F 0.2 2.5 2.5 2.5 5.0 5.0 5.0
Body Inclination h 2.0 0 0 0 0 0 0
Tape Width W 0.5 18.0 18.0 18.0 18.0 18.0 18.0
Adhesive Tape Width W0 min. 9.5 9.5 9.5 9.5 9.5 12.5
Feeding Hole Alignment W1 0.5 9.0 9.0 9.0 9.0 9.0 9.0
Adhesive Tape Margin W 2 max. 2.0 2.0 2.0 2.0 2.0 2.0
Length from Seating Plane H 0.5 17.5 (18.0) 17.5 18.5 18.5 (5, 7mm L = 17.5) 17.5 20.0
Lead Clinch Height H0 0.5 16.5 (17.0) 16.5 16.5 16.5
Feeding Hole Dia. D 0 0.2 4.0 4.0 4.0 4.0 4.0 4.0
Total Tape Thickness t 0.2 0.7 0.7 0.7 0.7 0.7 0.7
Cut Lead Height A max. 11.0 11.0 11.0 11.0 11.0 11.0
Taping Code Ammo leader PB(PC) PC PE PA PA PG
Note : Refer to the drawing of each series for tolerance.
86
TAPING
Lead Taping Capacitors for Automatic Insertion
DRAWING DRAWING
P2 P
h P2 P
h
L L
H P1 F P1 F
W2 H W2
A W1 A W1
W0 t W0 W t
W
P0 d D0 P0 d D0
DIMENSIONS Unit : mm PACKAGING Q’ty(pcs.)/Box Unit : mm

Applicable Drawing No. Ammo
Description Symbol Tolerance 10 12.5 16 18 Tear off

Case Height L max. 27.0 27.0 37.5 37.5
Lead Dia. d 0.05 0.6 0.6 0.8 0.8

H
MINIATURE TYPES
Body Pitch P 1.0 12.7 15.0 25.4 30.0 30.0
Feeding Hole Pitch P0 0.2 12.7 15.0 12.7 15.0 15.0 W L
Feeding Hole Alignment P1 0.7 3.85 5.0 3.85 3.75 3.75 Size Ammo
D Case Height L H W Q’ty

Feeding Hole Alignment P2 1.0 6.35 7.5 6.35 7.5 7.5
3 5 3000
0.6
Lead Center Spacing F 0.2
5.0 5.0 7.5 7.5 4 5, 7 332 230 42 2500
Body Inclination h 2.0 0 0 0 0 5, 7
5 2000
Tape Width W 0.5 18.0 18.0 18.0 18.0 9, 11 332 230 49
5, 7 332 230 42
Adhesive Tape Width W0 min. 12.5 12.5 12.5 12.5 6.3 1500
9, 11 332 230 49
Feeding Hole Alignment W1 0.5 9.0 9.0 9.0 9.0 5 332 230 42
8 1000
Adhesive Tape Margin W2 max. 2.0 2.0 2.0 2.0 9, 11.5 332 230 49
9, 12.5, 16 332 190 51
Length from Seating Plane H 0.5 18.5 18.5 18.5 18.5 10 500
20, 25 332 190 59
Feeding Hole Dia. D0 0.2 4.0 4.0 4.0 4.0 12.5 16, 20, 25 342 240 62 400
Total Tape Thickness t 0.2 0.7 0.7 0.7 0.7 16, 20, 25 342 240 62
16 250
31.5, 35.5 342 240 74
Cut Lead Height A max. 11.0 11.0 11.0 11.0
16, 20, 25 342 240 62
leader PH PL PA PA 18 200
Taping Code Ammo PA 31.5, 35.5 342 240 74
87
Lead Forming & Cutting

Unit : mm
Case Drawing
Configurations Shape Code
dia. L F
P F 1.0
T - Type D 8 TS 4.5 5.0
2 max.
L 2 max.
1.1
S - Type D 10 P SS 4.5 -
2 max.
P F
F - Type D 8 FS 5.0 5.0
2 max.
L
P
C - Type ALL CS 5.0 -
Case
Shape Drawing
dia.
M M
Configurations R0
.4 .4
D 8 D D R0 M N
90 90
P N N P
D - Type DL DR 3.0 3.2
H - Type HL HR 3.0 3.7
M - Type Code ML MR 6.0 2.5
Q - Type QL QR 6.0 1.5
J - Type JL JR 6.0 0.5
88
Standard, For General Purposes

SD Series Solvent Proof
WV 100V
Standard series for general purposes

High voltage, high capacitance series
Voltage range of 6.3~500V
Complied to the RoHS directive
WV 6.3 ~ 450 500

Operating temperature range
Temperature range -40 ~ +85 C -25 ~ +85 C
WV 100 WV > 100

Leakage current max. I = 0.01CV or 3 A whichever is greater (after 2 min)
I = 0.02CV+15 A (after 5 min)
I = 0.03CV or 4 A whichever is greater (after 1 min)
Capacitance tolerance 20% at 120Hz, 20 C
Capacitance > 1000 F : tan increases by 0.02 for each 1000 F from below value.
WV 6.3 10 16 25 35 50 63 100 160 ~ 250 350 ~ 500
(at 120Hz, 20 C)
tan 0.28 0.24 0.20 0.16 0.14 0.12 0.10 0.08 0.15 0.20
WV 6.3 10 16 25 35 50~100 160 200~350 400~450 500


Z-25 C/Z+20 C 5 4 3 2 2 2 4 6 10 12
Z-40 C/Z+20 C 12 10 8 5 4 3 6 8

(after application of the rated Capacitance change Within 20% of initial value
voltage for 2000 hours at 85 C) tan Less than 200% of specified value
After 1000 hours no load test, leakage current, capacitance and tan are same as load life value.
Shelf life (at 85 C)
The measurement shall be performed at 20 C by the KS C IEC 60384 - 4
DRAWING Unit : mm
Insulating sleeve d 0.05 Tinned copper-ply wire
MINIATURE TYPES
D 5 6.3 8 10 12.5 16 18 22
max.
P 0.5
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0
0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0
D
0.5 1.0
L max. 15 min. 4 min.
1.5 2.0 3.0
Safety vent( 6.3 up)
FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency
WV 60Hz 120Hz 1kHz 10kHz 50kHz 100kHz
F
~ 47 0.75 1.00 1.55 2.00 2.00 2.00

6.3~100 68 ~ 680 0.80 1.00 1.35 1.50 1.62 1.75
1000 ~ 0.85 1.00 1.15 1.15 1.32 1.50
~ 220 0.80 1.00 1.40 1.60 1.70 1.80
160~500
330 ~ 0.90 1.00 1.13 1.15 1.32 1.50
89
SD series
DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT
WV
6.3 10 16 25 35 50 63 100 160 200 250 350 400 450 500
F
5 11 5 11 5 11 8 11.5
1.0
21 23 23 26
5 11 5 11 5 11 8 11.5
1.5
26 28 28 32
5 11 5 11 5 11 8 11.5
2.2
32 34 34 33
5 11 5 11 5 11 6.3 11 6.3 11 6.3 11 8 11.5 8 11.5 8 11.5
3.3
39 42 42 45 45 48 53 56 50
5 11 5 11 5 11 6.3 11 6.3 11 6.3 11 8 11.5 10 12.5 10 12.5 10 16
4.7
46 50 50 53 57 57 66 61 72 69
5 11 5 11 5 11 8 11.5 8 11.5 8 11.5 10 12.5 10 12.5 10 16 10 16
6.8
56 60 60 76 76 76 88 87 86 76
5 11 5 11 5 11 8 11.5 8 11.5 10 12.5 10 12.5 10 16 10 20 12.5 25
10
68 72 76 96 96 107 107 115 115 178
5 11 5 11 6.3 11 10 12.5 10 16 10 16 10 20 12.5 20 12.5 20
15
83 89 89 131 143 143 156 165 164
5 11 5 11 6.3 11 10 12.5 10 16 10 16 12.5 20 12.5 20 12.5 25 16 25
22
101 108 124 156 173 170 222 218 217 265
5 11 6.3 11 8 11.5 10 16 10 20 10 20 16 20 12.5 25 16 25 16 31.5
33
123 151 178 209 232 247 297 296 294 310
5 11 6.3 11 6.3 11 8 11.5 10 20 10 20 12.5 20 16 20 16 25 16 31.5 18 31.5
47
131 169 181 222 293 293 319 353 387 384 412
5 11 6.3 11 6.3 11 8 11.5 10 12.5 12.5 20 12.5 25 16 20 16 25 16 31.5 16 35.5 18 35.5
68
144 182 203 256 293 391 426 425 465 488 503 457
5 11 5 11 6.3 11 8 11.5 8 11.5 10 16 12.5 25 16 25 16 25 18 31.5 18 35.5 18 40
100
162 181 220 291 311 388 516 516 564 592 667 546
5 11 6.3 11 8 11.5 10 12.5 10 12.5 10 20 16 20 16 25 16 31.5 18 40 18 40 22 45
150
198 246 318 414 422 528 632 691 726 845 863 1283
5 11 5 11 6.3 11 6.3 11 8 11.5 10 12.5 10 16 12.5 20 16 25 18 31.5 18 35.5 22 41 22 45
220
201 218 276 327 386 501 586 737 873 962 988 1112 1183
6.3 11 6.3 11 6.3 11 8 11.5 10 12.5 10 16 10 20 12.5 25 16 35.5 18 35.5 22 41
330
283 307 359 431 549 672 784 1002 1152 1206 1495
6.3 11 6.3 11 8 11.5 10 12.5 10 16 10 20 12.5 20 16 25 18 40 22 41
470
338 366 476 550 740 875 1098 1328 1434 1495
8 11.5 8 11.5 8 11.5 10 16 10 20 12.5 20 12.5 25 16 31.5 22 41
680
480 520 600 754 947 1235 1440 1643 1831
8 11.5 10 12.5 10 12.5 10 16 12.5 20 12.5 25 16 25 18 31.5
1000
581 659 796 942 1306 1633 1937 1965
10 16 10 16 10 20 12.5 20 16 25 16 31.5 18 31.5
2200
983 1051 1331 1542 2032 2220 2445
10 20 12.5 20 12.5 20 16 25 16 31.5 18 31.5 18 40
3300
1286 1545 1686 2194 2502 2765 2987
12.5 20 12.5 25 12.5 25 16 25 16 35.5 18 40
4700
1736 1903 2129 2448 2905 3272
12.5 25 16 25 16 25 18 31.5 18 40 Case size D L (mm)
6800
2129 2332 2577 3114 3408 Ripple current (mA rms) at 85 C, 120Hz
16 25 16 31.5 16 31.5 18 40
10000
2629 2830 3176 3544
16 35.5 16 35.5 18 35.5
15000
2959 3284 3656
18 40 18 40 22 41
22000
3733 3843 4012
Size 8 9 is available for capacitors marked “ ”
90
SD series
TYPICAL PERFORMANCE
16V 1000 F
400V 10 F
TEMPERATURE CHARACTERISTICS LOAD LIFE (at +85 C)

Capacitance change vs. temperature Capacitance change vs. time
100 30
80
20
60
Capacitance change ( )
40 10
20
0 0
-20
-10
-40
-60
-20
-80
-100 -30
-60 -10 40 90 0 500 1000 2000
Temperature ( C) Time (hours)
Dissipation factor vs. temperature Dissipation factor vs. time

1000 0.5
100 0.4
Dissipation factor
Dissipation factor
10 0.3
1 0.2
0.1 0.1
MINIATURE TYPES
0.01 0
-100 -50 0 50 100 150 500 1000 2000
FREQUENCY CHARACTERISTICS
Impedance vs. frequency Leakage current vs. time
10000 100
1000
Leakage current ( A)
80
100
Impedance ( )
60
10
40
1
20
0.1
0.01 0
0 1 10 100 500 1000 2000
Frequency (kHz) Time (hours)
91
Standard, Height 7mmL

SS Series Miniaturized Solvent Proof
Super miniature series with 7mmL height

Suited for use in compact audio equipment
Load life of 2000 hours at 85 C
Operating temperature range -40 ~ +85 C

Leakage current max. I = 0.01CV or 4 A whichever is greater (after 1 minute)
Dissipation factor max. WV 4 6.3 10 16 25 35, 40 50 63
(at 120Hz, 20 C) tan 0.35 0.24 0.20 0.16 0.14 0.12 0.10 0.10
WV 4 6.3 10 16, 25 35 ~ 63
Z-25 C/Z+20 C 6 4 3 2 2
Z-40 C/Z+20 C 12 8 6 4 3

DRAWING (See page 99) Unit : mm

WV 4 6.3 10 16 25 35 40 50 63
F
1.0 4 7 14 4 7 14
1.5 4 7 17 4 7 17
2.2 4 7 21 4 7 21
3.3 4 7 25 4 7 25
4.7 4 7 30 4 7 30
6.8 4 7 33 4 7 33 4 7 37 5 7 42
10 4 7 37 4 7 40 4 7 40 5 7 51 5 7 51
15 4 7 43 4 7 46 5 7 57 5 7 57 6.3 7 72 6.3 7 72
22 4 7 46 4 7 52 5 7 64 5 7 69 6.3 7 80 6.3 7 88
33 4 7 43 4 7 52 4 7 57 5 7 73 5 7 78 6.3 7 98 6.3 7 98
47 4 7 51 4 7 62 5 7 78 5 7 87 6.3 7 108
68 5 7 71 5 7 86 5 7 94 6.3 7 122
100 5 7 86 5 7 104 6.3 7 132 6.3 7 148
Ripple current (mA rms) at 85 C, 120Hz
150 6.3 7 122 6.3 7 148 6.3 7 162
Case size D L (mm)
220 6.3 7 148 6.3 7 179

Frequency
60Hz 120Hz 1kHz 10kHz 50kHz 100kHz
F
~ 47 0.75 1.00 1.55 2.00 2.00 2.00

68 ~ 680 0.80 1.00 1.35 1.50 1.62 1.75
92
Standard, Height 5mmL

SE Series Miniaturized Solvent Proof
Ultra miniature series with 5mmL height

Suitable to replace tantalum capacitors at low cost

WV 4 6.3 10 16 25 35 50 63
(at 120Hz, 20 C)
tan 0.35 0.24 0.20 0.16(0.20) 0.13(0.15) 0.12(0.14) 0.09(0.11) 0.09(0.11)
Figures in ( ) are for 3 products.
WV 4 6.3 10 16 ~ 63
Z-25 C/Z+20 C 6 4 3 2
Z-40 C/Z+20 C 12 8 6 4

DRAWING (See page 100) Unit : mm

WV 4 6.3 10 16 25 35 50 63
F
MINIATURE TYPES
1.0 4 5(3 5) 13(9.8) 4 5(3 5) 13(9.8)
1.5 4 5(3 5) 16(12) 4 5 16
2.2 4 5(3 5) 17(13) 4 5 19 4 5 19
3.3 4 5(3 5) 20(15) 4 5 20 4 5 24 5 5 27
4.7 4 5(3 5) 21(16) 4 5 23 4 5 24 5 5 33 5 5 33
6.8 4 5(3 5) 23(19) 4 5 25 4 5 28 5 5 34 5 5 39 6.3 5 46
10 4 5(3 5) 21(17) 4 5(3 5) 25(21) 4 5 28 4 5 31 5 5 40 5 5 41 6.3 5 56 6.3 5 56
15 4 5(3 5) 26(21) 4 5 31 4 5 34 5 5 44 5 5 49 6.3 5 59 6.3 5 68 8 5 81
22 4 5(3 5) 31(26) 4 5 37 5 5 47 5 5 53 6.3 5 69 6.3 5 72 8 5 98 8 5 98
33 4 5 38 5 5 53 5 5 58 6.3 5 76 6.3 5 84 8 5 104 8 5 120
47 4 5 45 5 5 63 6.3 5 81 6.3 5 91 8 5 119 8 5 124
68 5 5 63 6.3 5 89 6.3 5 98 6.3 5 109 8 5 143
100 5 5 89 6.3 5 108 8 5 140 8 5 157 8 5 174
150 6.3 5 109 8 5 157 8 5 172 8 5 192
220 6.3 5 133 8 5 190 8 5 208 Ripple current (mA rms) at 85 C, 120Hz
330 8 5 192 Case size D L (mm)

Frequency
F
~ 47 0.75 1.00 1.55 2.00 2.00 2.00

68 ~ 0.80 1.00 1.35 1.50 1.62 1.75
93
Wide Temperature Range

RD Series Solvent Proof
WV 100V
Standard series for general purpose

High CV value
Wide operating temperature range of -55 ~ +105 C
WV 6.3 ~ 100 160 ~ 450 500

Temperature range -55 ~ +105 C -40 ~ +105 C -25 ~ +105 C
WV 100 WV > 100

WV 6.3 10 16 25 35 50 63 100 160~250 350~500
(at 120Hz, 20 C)
tan 0.28 0.24 0.20 0.16 0.14 0.12 0.10 0.08 0.15 0.20
WV 6.3 10 16 25 35 50~100 160 200~350 400~450 500

Z-25 C/Z+20 C 5 4 3 2 2 2 4 6 10 12
Z-40 C/Z+20 C 12 10 8 5 4 3 6 8

Load life Capacitance change Within 20% of initial value
(after application of the rated tan Less than 200% of specified value
voltage for 2000 hours at 105 C)
D D 8 D 10
Unit : mm
DRAWING
D 5 6.3 8 10 12.5 16 18 22
max.
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0

P 0.5 d 0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0
D
0.5 1.0
L max. 15 min. 4 min. 1.5 2.0 3.0
Safety vent 6.3 up)

Frequency
F
~ 47 0.75 1.00 1.55 2.00 2.00 2.00

6.3~100 68 ~ 680 0.80 1.00 1.35 1.50 1.62 1.75
820 ~ 0.85 1.00 1.15 1.15 1.32 1.50
~ 220 0.80 1.00 1.40 1.60 1.70 1.80
160~500
330 ~ 0.90 1.00 1.13 1.15 1.32 1.50
94
RD series

WV
6.3 10 16 25 35 50 63 100 160 200 250 350 400 450 500

F
5 11 5 11 5 11 6.3 11 6.3 11 6.3 11 8 11.5 8 11.5 10 12.5

2.2
24 26 26 23 23 23 28 28 27
5 11 5 11 5 11 6.3 11 6.3 11 8 11.5 8 11.5 10 12.5 10 16
3.3
29 32 32 29 29 34 34 39 36
5 11 5 11 5 11 6.3 11 8 11.5 8 11.5 10 12.5 10 12.5 10 16 10 16
4.7
35 38 38 34 40 40 47 47 43 59
5 11 5 11 5 11 8 11.5 10 12.5 10 12.5 10 16 10 16 10 20 10 16
6.8
42 46 46 49 56 56 62 62 56 72
5 11 5 11 5 11 10 12.5 10 12.5 10 12.5 10 16 10 20 12.5 20 12.5 25
10
51 56 56 68 68 68 75 82 80 88
5 11 5 11 6.3 11 10 16 10 16 10 16 10 20 12.5 20 12.5 25 12.5 30
15
62 68 78 92 92 92 100 118 107 115
5 11 5 11 6.3 11 10 16 10 16 10 20 12.5 20 12.5 25 16 25 16 25
22
75 83 95 111 111 121 143 155 144 159
5 11 6.3 11 8 11.5 10 20 10 20 12.5 20 12.5 25 16 25 16 31.5 16 31.5
33
92 116 137 149 149 175 190 211 193 207
5 11 6.3 11 6.3 11 10 12.5 12.5 20 12.5 20 12.5 25 16 25 16 31.5 16 31.5 18 31.5
47
96 127 139 190 208 208 227 252 276 230 261
5 11 6.3 11 8 11.5 8 11.5 10 16 12.5 25 16 20 16 25 16 31.5 18 35.5 18 31.5 18 35.5
68
108 132 180 197 251 273 279 303 332 373 285 335
6.3 11 6.3 11 8 11.5 8 11.5 10 20 12.5 25 16 25 16 31.5 18 35.5 18 40 18 31.5 18 40
82
137 145 198 216 290 302 333 364 369 387 327 370
5 11 6.3 11 6.3 11 8 11.5 8 11.5 10 20 12.5 25 16 25 16 31.5 18 35.5 18 40 18 40
100
119 151 160 218 239 332 331 368 402 407 427 486
5 11 6.3 11 6.3 11 8 11.5 10 12.5 10 12.5 12.5 20 16 25 16 35.5 18 35.5 18 40 22 41
150
134 167 185 231 310 340 477 450 517 554 523 596
5 11 5 11 6.3 11 8 11.5 8 11.5 10 12.5 10 16 12.5 25 16 31.5 18 35.5 18 40 22 41
220
146 162 203 264 280 376 451 630 596 671 694 721
6.3 11 6.3 11 8 11.5 8 11.5 10 12.5 10 16 10 20 16 25 18 35.5 18 40 22 41
330
206 228 293 324 399 504 603 856 822 850 968
6.3 11 6.3 11 8 11.5 10 12.5 10 16 10 20 12.5 20 16 25 18 40 22 41
470
246 272 349 449 521 657 844 1021 1015 1155
8 11.5 10 12.5 10 12.5 10 16 12.5 16 12.5 20 12.5 25 16 31.5 22 41
MINIATURE TYPES
680
348 449 488 591 740 927 1107 1344 1390
8 11.5 10 12.5 10 16 10 20 12.5 20 12.5 25 16 25 16 35.5
820
382 493 587 708 880 1050 1300 1627
8 11.5 10 12.5 10 16 10 20 12.5 20 12.5 25 16 25 18 40
1000
422 544 648 820 974 1226 1490 1925
10 16 10 16 12.5 16 12.5 20 16 20 16 25 16 35.5
1500
621 680 862 1017 1188 1442 1770
12.5 20
10 20 10 20 12.5 20 1100 16 25 16 31.5 16 35.5
2200
778 844 1055 12.5 25 1426 1442 1770
1235
12.5 16 12.5 20 12.5 25 16 25 16 35.5 16 35.5 18 40
3300
983 1148 1323 1562 1857 1794 2689
12.5 20 12.5 25 16 25 16 31.5 18 35.5 Case size D L (mm)
4700
12.5 25 16 25 16 31.5 18 35.5
6800
1480 1737 1982 2335
16 25 16 35.5 18 35.5
10000
1807 2172 2409
16 35.5 18 35.5
15000
2233 2482
18 40
22000
2652
Size 8 9 is available for capacitors marked “ ”
95
RD series
TYPICAL PERFORMANCE
16V 1000 F
400V 10 F
TEMPERATURE CHARACTERISTICS LOAD LIFE (at +105 C)

Capacitance change vs. temperature Capacitance change vs. time
100 30
80
20
60
40 10
20
0 0
-20
-10
-40
-60
-20
-80
-100 -30
-60 -10 40 90 0 500 1000 2000
Dissipation factor vs. temperature Dissipation factor vs. time

1000 0.5
100 0.4
Dissipation factor
Dissipation factor
10 0.3
1 0.2
0.1 0.1
0.01 0
-100 -50 0 50 100 150 500 1000 2000
FREQUENCY CHARACTERISTICS
Impedance vs. frequency Leakage current vs. time
10000 100
1000
Leakage current ( A)
80
100
Impedance ( )
60
10
40
1
20
0.1
0.01 0
0 1 10 100 500 1000 2000
Frequency (kHz) Time (hours)
96
Wide Temperature Range, Miniaturized

RM Series Miniaturized Solvent Proof
WV 100V
Miniature size compared with RD series

High CV value
WV 6.3 ~ 100 160 ~ 450

WV 100 WV > 100

WV 6.3 10 16 25 35 50 63 100 160~250 350~450
(at 120Hz, 20 C)
tan 0.28 0.24 0.20 0.16 0.14 0.12 0.10 0.08 0.15 0.20
WV 6.3 10 16 25 35 50~100 160 200~250 350~400 450

Z-25 C/Z+20 C 5 4 3 2 2 2 3 4 6 8
Z-40 C/Z+20 C 10 8 6 4 3 3 4 8 10 12

(after application of the rated tan Less than 200% of specified value
D D 8 D 10
DRAWING Unit : mm
MINIATURE TYPES
D 0.5 max.
D 6.3 8 10 12.5 16 18
P 0.5 P 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.6 0.6 0.6 0.8 0.8
L max. 15 min. 4 min. 1.5 2.0
Safety vent 6.3 up)

Frequency
F
~ 47 0.75 1.00 1.55 2.00 2.30 2.00

6.3~100 68 ~ 680 0.80 1.00 1.35 1.50 1.62 1.75
1000 ~ 0.85 1.00 1.15 1.15 1.32 1.50
~ 220 0.80 1.00 1.40 1.60 1.70 1.80
160~500
330 ~ 0.90 1.00 1.13 1.15 1.32 1.50
97
RM series

WV
6.3 10 16 25 35 50 63 100 160 200 250 350 400 450

F
6.3 11
1.0
13
6.3 11 8 11.5 8 11.5
2.2
23 28 23
6.3 11 8 11.5 8 11.5 10 12.5
3.3
30 34 34 33
6.3 11 8 11.5 8 11.5 10 12.5 10 12.5
4.7
34 40 40 47 39
8 11.5 10 12.5 10 12.5 10 16 10 16
6.8
49 56 56 62 52
8 11.5 8 11.5 10 12.5 10 16 10 16 10 20
10
59 59 68 75 75 68
10 12.5 10 12.5 10 16 10 16 12.5 20 12.5 20
15
84 84 92 92 115 96
10 12.5 10 16 10 16 12.5 20 12.5 20 12.5 25
22
102 111 111 139 140 127
8 11.5 10 16 10 20 10 20 12.5 25 16 25 16 25
33
139 136 149 149 180 211 117
10 12.5 10 20 12.5 20 12.5 20 16 25 16 25 16 31.5
47
190 177 203 203 252 252 231
10 12.5 12.5 25 16 20 12.5 25 16 31.5 16 31.5 16 35.5
68
229 267 279 267 303 332 291
8 11.5 8 11.5 10 16 12.5 25 16 25 16 25 18 31.5 18 35.5 18 40
100
218 239 304 324 368 368 432 453 397
8 11.5 10 12.5 10 20 16 25 16 25 16 31.5 18 35.5
150
267 293 372 450 450 450 554
6.3 11 8 11.5 10 12.5 10 16 12.5 20 16 31.5 18 31.5 18 35.5
220
224 280 376 451 564 596 641 671
6.3 11 8 11.5 10 12.5 10 16 10 20 16 25 18 31.5 18 40
330
248 324 400 504 603 856 784 863
6.3 11 8 11.5 8 11.5 10 12.5 10 20 12.5 20 16 25 18 40
470
272 349 386 476 657 824 1021 1030
6.3 11 8 11.5 8 11.5 10 12.5 10 16 12.5 20 12.5 25 16 31.5
680
295 386 420 540 627 905 1082 1344
8 11.5 8 11.5 10 12.5 10 16 10 20 12.5 25 16 25 18 35.5
1000
422 469 592 717 829 1197 1490 1835
10 16 10 16 10 20 12.5 20 12.5 25 16 31.5 18 31.5
1500
621 680 797 993 1136 1578 1812
10 16 10 16 10 20 12.5 25 16 25 16 31.5 18 31.5
2200
713 774 898 1206 1426 1709 1935
10 20 10 20 12.5 20 16 25 16 31.5 18 35.5
3300
909 978 1184 1562 1769 2152

12.5 20 12.5 20 12.5 25 16 25 16 35.5
4700
1189 1272 1459 1752 2073
12.5 25 16 25 16 25 16 35.5 18 40 Case size D L (mm)
6800
16 25 16 25 16 31.5 18 35.5
10000
1807 1892 2140 2497
16 31.5 16 35.5 18 35.5
15000
2128 2313 2545
18 31.5 18 35.5
22000
2411 2595
98
Wide Temperature Range, Height 7mmL

RK Series Solvent Proof

High performance and excellent temperature characteristics

Dissipation factor max. WV 4 6.3 10 16 25 35 50 63
(at 120Hz, 20 C) tan 0.35 0.22 0.19 0.15 0.12 0.12 0.10 0.10
WV 4 6.3 10 16 25, 35 50, 63

Z-25 C/Z+20 C 6 4 3 2 2 2
Z-40 C/Z+20 C 12 10 8 6 4 3

DRAWING Unit : mm
D 4 5 6.3
D 0.5 max.
P 1.5 2.0 2.5

P 0.5 d 0.45 0.5 0.5
1.0 1.5 1.5
MINIATURE TYPES
WV
F
4 6.3 10 16 25 35 50 63
1.0 4 7 9.1 4 7 9.1

2.2 4 7 14 5 7 16
3.3 4 7 15 5 7 19 6.3 7 22
4.7 4 7 18 5 7 21 6.3 7 26 6.3 7 26
6.8 4 7 19 5 7 25 5 7 25 6.3 7 32
10 4 7 21 4 7 24 5 7 30 6.3 7 35
22 4 7 29 5 7 36 5 7 40 6.3 7 52
33 4 7 28 5 7 40 6.3 7 51 6.3 7 57
47 4 7 33 5 7 47 6.3 7 60 Ripple current (mA rms) at 105 C, 120Hz
Case size D L (mm)
68 5 7 46 6.3 7 67

Frequency
F
~ 47 0.75 1.00 1.55 2.00 2.00 2.00

68 ~ 0.80 1.00 1.35 1.50 1.62 1.75
99
Wide Temperature Range, Height 5mmL

RE Series Miniaturized Solvent Proof
Ultra miniature series with 5mmL height

Suitable to replace tantalum capacitors at low cost

Leakage current max. I = 0.01CV or 3 A whichever is greater (after 2 minutes)
(at 120Hz, 20 C) tan 0.35 0.27 0.23 0.19 0.15 0.13 0.11
WV 4 6.3 10 16 25~50

Z-25 C/Z+20 C 7 3 3 2 2
Z-40 C/Z+20 C 12 8 5 4 3


DRAWING Unit : mm
D 3 4 5 6.3 8
D 0.5 max.
P 1.0 1.5 2.0 2.5 2.5

P 0.5
d 0.4 0.45 0.45 0.45 0.45
1.0 1.5

WV 4 6.3 10 16 25 35 50
F
1.0 4 5(3 5) 7.7(6.4)

1.5 4 5(3 5) 9.4(7.8)
2.2 4 5(3 5) 11(9.5)
3.3 4 5(3 5) 13(11) 4 5 14
4.7 4 5(3 5) 14(12) 4 5 15 5 5 19
6.8 4 5 17 5 5 21 5 5 23
10 4 5(3 5) 15(13) 4 5(3 5) 17(14) 4 5(3 5) 18(15) 5 5 24 5 5 26 6.3 5 33
15 4 5(3 5) 17(14) 4 5 19 4 5 21 5 5 26 5 5 29 6.3 5 37 6.3 5 40
22 4 5 20 4 5 23 5 5 29 5 5 32 6.3 5 42 6.3 5 45 8 5 58
33 4 5 25 5 5 32 5 5 35 6.3 5 45 6.3 5 51 8 5 65 8 5 71
47 4 5 29 5 5 39 6.3 5 49 6.3 5 54 8 5 72 8 5 77
68 5 5 41 6.3 5 55 6.3 5 59 8 5 77 8 5 87
100 5 5 50 6.3 5 66 8 5 85 8 5 93
150 6.3 5 71 8 5 96 8 5 104 Ripple current (mA rms) at 105 C, 120Hz
220 8 5 102 8 5 116 Case size D L (mm)

Frequency
F
~ 47 0.75 1.00 1.55 2.00 2.00 2.00

68 ~ 0.80 1.00 1.35 1.50 1.62 1.75
100
High Ripple Current, Height 7mmL

ZS Series Miniaturized Solvent Proof Low Impedance

High ripple current compared with RK series

I = 0.01CV or 3 A whichever is greater (after 2 minutes)
Leakage current
I = 0.03CV or 4 A whichever is greater (after 1 minute)
(at 120Hz, 20 C) tan 0.22 0.19 0.16 0.14 0.12 0.10
WV 6.3 10 16 25 35 50
Z-25 C / Z+20 C 2 2 2 2 2 2
Z-40 C / Z+20 C 6 4 3 3 3 3
After an application of DC bias voltage plus the rated AC ripple current for 2000 hours at 105 C.
The measurement shall meet the following limits. The DC voltage plus the peak AC voltage
combined must not exceed the rated voltage.
Load life
Capacitance change Within 25% of the initial value
tan Less than 200% of the specified value
DRAWING Insulating sleeve d 0.05 Tinned copper-ply wire

Unit : mm
D 0.5 max.
D 5 6.3 8
P 0.5 P 2.0 2.5 3.5

d 0.5 0.5 0.5
L 1.5 max. 15 min. 4 min.
MINIATURE TYPES
WV 6.3 10 16 25 35 50
Item Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple
current current current current current current

D L max. D L max. D L max. D L max. D L max. D L max.
(mA rms) (mA rms) (mA rms) (mA rms) (mA rms) (mA rms)
(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C 105 C 105 C
F 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
2.2 5 7 2.00 165

4.7 5 7 2.00 165
10 6.3 7 0.90 235
22 5 7 1.40 165 6.3 7 0.90 260
33 5 7 1.40 165 5 7 1.40 165 5 7 1.40 165 5 7 1.40 165 6.3 7 0.70 235 8 7 0.50 350
47 5 7 1.40 165 5 7 1.40 165 5 7 1.40 165 6.3 7 0.70 235 8 7 0.34 350 8 7 0.50 450
68 6.3 7 0.70 235 6.3 7 0.70 235 6.3 7 0.70 235 6.3 7 0.70 235 8 7 0.34 350
100 6.3 7 0.70 235 6.3 7 0.70 235 6.3 7 0.70 235 8 7 0.34 350
150 6.3 7 0.70 235 6.3 7 0.70 235 8 7 0.34 350
220 8 7 0.34 350 8 7 0.34 350
330 8 7 0.34 350

Frequency
F 120Hz 1kHz 10kHz 50kHz 100kHz
~ 33 0.35 0.55 0.75 0.87 1.00

47 ~ 150 0.40 0.60 0.80 0.90 1.00
220 ~ 0.50 0.65 0.85 0.92 1.00
101

ZL Series Miniaturized Solvent Proof Low Impedance


Leakage current
(at 120Hz, 20 C) tan 0.22 0.19 0.16 0.14 0.12 0.10

WV 6.3 10 16 25 35 50
Z-25 C / Z+20 C 2 2 2 2 2 2
Z-40 C / Z+20 C 6 4 3 3 3 3
Load life
DRAWING Unit : mm

D 0.5 max.
D 5 6.3 8
P 0.5 P 2.0 2.5 3.5

d 0.5 0.5 0.5

WV 6.3 10 16 25 35 50
Item Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple
current current current current current current

D L max. D L max. D L max. D L max. D L max. D L max.
(mA rms) (mA rms) (mA rms) (mA rms) (mA rms) (mA rms)
(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C 105 C 105 C
F 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
2.2 5 7 1.00 165

10 6.3 7 0.42 235
22 5 7 0.84 165 6.3 7 0.42 235
33 5 7 0.84 165 5 7 0.84 165 5 7 0.84 165 5 7 0.84 165 6.3 7 0.42 235 8 7 0.20 350
47 5 7 0.84 165 5 7 0.84 165 5 7 0.84 165 6.3 7 0.42 235 8 7 0.20 350 8 7 0.20 350
68 6.3 7 0.42 235 6.3 7 0.42 235 6.3 7 0.42 235 6.3 7 0.42 235 8 7 0.20 350
100 6.3 7 0.42 235 6.3 7 0.42 235 6.3 7 0.42 235 8 7 0.20 350
150 6.3 7 0.20 235 6.3 7 0.42 235 8 7 0.20 350
220 8 7 0.20 350 8 7 0.20 350
330 8 7 0.20 350
FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT (See page 103)
102

ZE Series Miniaturized Solvent Proof Low Impedance

High ripple current & high temperature with RE series

Leakage current
Dissipation factor max. WV 6.3 10 16 25 35

(at 120Hz, 20 C) tan 0.22 0.20 0.18 0.14 0.12
WV 6.3 10 16 25 35
Z-25 C / Z+20 C 3 3 2 2 2
Z-40 C / Z+20 C 9 7 5 3 3
Load life
DRAWING Unit : mm
D 5 6.3
D 0.5 max.
2.0 2.5
MINIATURE TYPES
P
P 0.5
d 0.45 0.45

Frequency
F 120Hz 1kHz 10kHz 50kHz 100kHz
~ 33 0.35 0.55 0.75 0.87 1.00

47 ~ 0.40 0.60 0.80 0.90 1.00
103
ZE series

WV 6.3 10 16 25 35
Item Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple Imp.(Ω) Ripple
current current current current current

D L max. D L max. D L max. D L max. D L max.
(mA rms) (mA rms) (mA rms) (mA rms) (mA rms)
(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C 105 C
F 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
1 5 5 2.40 100
1.5 5 5 2.40 100
2.2 5 5 2.40 100
3.3 5 5 2.40 100
4.7 5 5 2.40 100
6.8 5 5 2.40 100
10 5 5 2.40 100 5 5 2.40 100
15 5 5 2.40 100 5 5 2.40 100 5 5 2.40 100
22 5 5 2.40 100 5 5 2.40 100 6.3 5 0.75 140
33 5 5 2.40 100 5 5 2.40 100 5 5 2.40 100 6.3 5 0.75 140 6.3 5 0.75 140
47 5 5 2.40 100 5 5 2.40 100 6.3 5 0.75 140 6.3 5 0.75 140
68 6.3 5 0.75 140 6.3 5 0.75 140 6.3 5 0.75 140
100 6.3 5 0.75 140 6.3 5 0.75 140
104
Extremely Low Impedance

RZ Series Long Life Solvent Proof Low Impedance
Extremely low impedance at high frequency

High reliability withstanding 5000 hours load life at 105 C
(2000 / 3000 hours for smaller case sizes as specified below)
Ideally suited for use in switching power supplies

Capacitance > 1000 F : tan increases by 0.02 for each 1000 F from below value
WV 6.3 10 16 25 35 50 63
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.10 0.08
Low temperature characteristics WV 6.3, 10 16 ~ 35 50, 63

(Impedance ratio at 120Hz) Z-55 C/Z+20 C 4 3 2
tan Less than 200% of specified value
D D 6.3 D=8 D 10
Capacitance change Within 20% of initial value
DRAWING Unit : mm
MINIATURE TYPES
D 0.5 max.
D 5 6.3 8 10 12.5 16 18
P 0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L max. 15 min. 4 min. 1.5 2.0
Safety vent 6.3 up)

Frequency
120Hz 1kHz 10kHz 50kHz 100kHz
F
~ 33 0.40 0.65 0.82 0.91 1.00

47 ~ 220 0.50 0.70 0.84 0.92 1.00
330 ~ 680 0.55 0.75 0.86 0.93 1.00
1000 ~ 1500 0.60 0.80 0.88 0.94 1.00
2200 ~ 0.70 0.85 0.90 0.95 1.00
105
RZ series

WV 6.3 10 16 25
Item Impedance Ripple current Impedance Ripple current Impedance Ripple current Impedance Ripple current
D L (Ω)max. (mA rms) D L (Ω)max. (mA rms) D L (Ω)max. (mA rms) D L (Ω)max. (mA rms)
20 C 105 C 20 C 105 C 20 C 105 C 20 C 105 C

(mm) (mm) (mm) (mm)
F 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
33 5 11 0.80 155
47 5 11 0.80 155 6.3 11 0.55 210
68 5 11 0.80 155 6.3 11 0.50 220 6.3 11 0.36 260
100 5 11 0.85 150 6.3 11 0.55 210 6.3 11 0.35 265 8 11.5 0.24 383
150 6.3 11 0.49 225 6.3 11 0.35 265 8 11.5 0.23 388 8 11.5 0.16 460
220 6.3 11 0.30 285 8 11.5 0.24 387 8 11.5 0.16 460 10 12.5 0.13 600
330 8 11.5 0.20 292 8 11.5 0.16 460 10 12.5 0.12 625 10 16 0.095 750
470 10 12.5 0.14 575 10 12.5 0.13 600 10 16 0.09 770 10 20 0.065 1020
680 10 16 0.11 700 10 16 0.09 770 10 20 0.065 1020 12.5 20 0.046 1392
1000 10 20 0.075 950 10 20 0.060 1060 12.5 20 0.047 1411 12.5 25 0.036 1660
1500 10 25 0.055 1220 12.5 20 0.045 1417 12.5 25 0.036 1660 16 20 0.034 1770
2200 12.5 20 0.043 1438 12.5 25 0.034 1710 16 20 0.033 1800 16 25 0.028 2051
3300 12.5 25 0.034 1710 16 20 0.031 1850 16 25 0.027 2095 16 35.5 0.020 2680
4700 16 25 0.032 1935 16 31.5 0.023 2420 16 35.5 0.020 2680 18 40 0.018 2960
6800 16 31.5 0.024 2370 16 35.5 0.020 2680 18 35.5 0.018 2900
10000 16 40 0.020 2750 18 40 0.017 3040
15000 18 40 0.018 2960
WV 35 50 63
Item Impedance Ripple current Impedance Ripple current Impedance Ripple current
D L (Ω)max. (mA rms) D L (Ω)max. (mA rms) D L (Ω)max. (mA rms)
20 C 105 C 20 C 105 C 20 C 105 C

(mm) (mm) (mm)
F 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
1.0 5 11 4.0 36
1.5 5 11 3.8 45
2.2 5 11 3.5 54
3.3 5 11 3.0 66
4.7 5 11 2.2 81
6.8 5 11 1.8 91
10 5 11 1.8 115 5 11 1.06 135
15 5 11 0.93 145 6.3 11 0.73 185
22 5 11 0.75 160 6.3 11 0.65 195 6.3 11 0.52 215
33 6.3 11 0.49 225 6.3 11 0.43 240 8 11.5 0.35 320
47 6.3 11 0.34 270 8 11.5 0.30 344 8 11.5 0.25 365
68 8 11.5 0.24 384 8 11.5 0.20 410 10 12.5 0.19 495
100 8 11.5 0.16 460 10 16 0.16 581 10 20 0.12 750
150 10 12.5 0.12 625 10 20 0.10 820 10 25 0.09 950
220 10 16 0.09 770 10 25 0.075 1040 12.5 20 0.065 1140
330 10 20 0.060 1060 12.5 20 0.075 1281 12.5 25 0.049 1420
470 12.5 20 0.046 1401 12.5 25 0.044 1500 16 25 0.042 1700
680 12.5 25 0.036 1660 16 20 0.040 1630 16 31.5 0.032 2050
1000 16 20 0.034 1770 16 31.5 0.030 2120 18 35.5 0.029 2280
1500 16 31.5 0.028 2385 16 40 0.026 2410
2200 16 35.5 0.020 2680 18 40 0.024 2560
3300 18 40 0.017 3040
106

WL Series Long Life Solvent Proof Low Impedance
WV 100V
Wide voltage compared with RZ series

Operating temperature range of 40 ~ +105 C
For E-meter
WV 6.3 ~ 450 500

WV 100 WV > 100

Leakage current max. I = 0.01CV or 3 A whichever is greater (after 2 min.)
I = 0.02CV + 15 A (after 5 min.)
I = 0.03CV or 4 A whichever is greater (after 1 min.)

WV 6.3 10 16 25 35 50 63 100 160~250 350~500
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 0.15 0.20
WV 6.3 10 16 25 ~ 100 160 ~ 250 350 ~ 450 500


Z-25 C/Z+20 C 4 3 2 2 3 6 8
Z-40 C/Z+20 C 8 6 4 3 4 10 --
Load life
Life time D = 5, 6.3 D=8 D 10
WV 100 2000 hours 3000 hours 5000 hours
WV > 100 2000 hours
Unit : mm
DRAWING
MINIATURE TYPES
D 5 6.3 8 10 12.5 16 18 20 22
max.
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0 10.0

P 0.5 d 0.5 0.5 0.6 0.6 0.6 0.8 0.8 0.8 1.0
D
0.5 1.0
L max. 15 min. 4 min. 1.5 2.0 3.0
Safety vent 6.3 up)

Frequency
F
~ 33 0.40 0.65 0.82 0.91 1.00

33 ~ 270 0.50 0.70 0.84 0.92 1.00
330 ~ 680 0.55 0.75 0.86 0.93 1.00
820 ~ 1800 0.60 0.80 0.88 0.94 1.00
2200 ~ 0.70 0.85 0.90 0.95 1.00
107
WL series

WV 6.3 10 16 25
Ripple Ripple Ripple Ripple

Item Impedance Impedance Impedance Impedance
current current current current
D L (Ω)max. D L (Ω)max. D L (Ω)max. D L (Ω)max.
(mA rms) (mA rms) (mA rms) (mA rms)
20 C 20 C 20 C 20 C
(mm) 105 C (mm) 105 C (mm) 105 C (mm) 105 C
100kHz 100kHz 100kHz 100kHz
F 100kHz 100kHz 100kHz 100kHz
10 5 11 0.70 180 5 11 0.70 180

22 5 11 0.70 180 5 11 0.70 180 5 11 0.70 180 5 11 0.70 180
33 5 11 0.70 180 5 11 0.70 180 5 11 0.70 180 5 11 0.70 180
47 5 11 0.65 180 5 11 0.65 180 5 11 0.65 180 5 11 0.65 180
100 5 11 0.65 180 5 11 0.65 180 6.3 11 0.30 280 6.3 11 0.30 280
150 6.3 11 0.30 280 6.3 11 0.30 280 6.3 11 0.30 280 8 11.5 0.14 450
220 6.3 11 0.30 280 6.3 11 0.30 280 8 11.5 0.14 450 8 11.5 0.14 450
330 6.3 11 0.30 280 8 11.5 0.14 450 8 11.5 0.14 450 10 12.5 0.10 660
470 8 11.5 0.14 450 8 11.5 0.14 450 10 12.5 0.10 660 10 16 0.080 850
680 10 12.5 0.10 660 10 12.5 0.10 660 10 16 0.080 850 10 20 0.054 1100
1000 10 12.5 0.10 660 10 16 0.080 850 10 20 0.054 1100 12.5 20 0.050 1400
1500 10 20 0.054 1100 10 20 0.054 1100 12.5 20 0.050 1400 16 20 0.030 2100
2200 12.5 20 0.050 1400 12.5 20 0.050 1400 12.5 25 0.038 1700 16 25 0.030 2100
3300 12.5 20 0.050 1400 12.5 25 0.038 1700 16 25 0.030 2100 16 31.5 0.025 2600
4700 16 25 0.030 2100 16 25 0.030 2100 16 31.5 0.025 2600 18 35.5 0.022 3000
6800 16 25 0.030 2100 16 31.5 0.025 2600 18 35.5 0.022 3000
10000 16 31.5 0.025 2600 18 35.5 0.022 3000
15000 18 35.5 0.022 3000
WV 35 50 63 100

Item Impedance Impedance Impedance Impedance
20 C 20 C 20 C 20 C
(mm) 105 C (mm) 105 C (mm) 105 C (mm) 105 C
100kHz 100kHz 100kHz 100kHz
1.0 5 11 3.5 40
2.2 5 11 3.0 55 5 11 2.5 52
3.3 5 11 2.6 65 5 11 2.0 64 5 11 2.5 64
4.7 5 11 0.70 180 5 11 2.3 90 5 11 2.0 76 5 11 2.5 76
10 5 11 0.70 180 5 11 1.4 120 5 11 2.0 111 6.3 11 1.0 128
22 5 11 0.70 180 5 11 1.2 150 6.3 11 0.60 190 8 11.5 0.60 224
33 5 11 0.65 180 6.3 11 0.60 200 6.3 11 0.60 233 10 12.5 0.40 319
47 6.3 11 0.30 280 6.3 11 0.43 250 8 11.5 0.50 328 10 16 0.30 417
100 8 11.5 0.20 450 8 11.5 0.24 340 10 16 0.12 456 12.5 20 0.15 570
150 8 11.5 0.14 450 10 12.5 0.17 490 10 20 0.10 610 12.5 25 0.12 762
220 10 12.5 0.10 660 10 16 0.12 650 10 25 0.090 809 16 25 0.070 1250
330 10 16 0.080 850 10 20 0.10 810 12.5 20 0.085 1036 16 31.5 0.050 1404
470 10 20 0.054 1100 12.5 20 0.085 1100 16 20 0.050 1411 18 40 0.030 1980
680 12.5 20 0.050 1400 12.5 25 0.065 1200 16 25 0.043 1843 18 40 0.030 2050
820 12.5 25 0.045 1500 16 25 0.055 1300 18 25 0.035 1900 18 40 0.030 2215
1000 12.5 25 0.038 1700 16 25 0.043 1600 16 35.5 0.025 1967
1500 16 25 0.030 2100 16 31.5 0.038 2000
2200 16 31.5 0.025 2600 18 35.5 0.034 2300
3300 18 35.5 0.022 3000
108
WL series

WV
160 200 250 350

Item
D L D L D L D L
(mm) 105 C (mm) 105 C (mm) 105 C (mm) 105 C
1 6.3 11 45
10 10 16 230 10 20 300 10 20 180
22 10 20 440 10 20 440 12.5 20 480 12.5 20 270
33 10 20 560 12.5 20 590 12.5 25 630 16 20 600
47 12.5 20 725 12.5 20 780 12.5 25 630 16 25 700
68 12.5 25 950 12.5 25 950 16 25 1000 16 31.5 1100
82 16 25 1100 16 35.5 1130
100 16 25 1280 16 25 1280 16 31.5 1400 18 31.5 1170
120 18 35.5 1200
18 25
150 16 31.5 1300 16 25 1500 1450 18 40 1250
18 31.5
18 35.5
220 16 31.5 1300 18 31.5 1700 1485
18 40
330 18 31.5 1700 18 35.5 1900
WV
400 420 450 500

Item
D L D L D L D L
(mm) 105 C (mm) 105 C (mm) 105 C (mm) 105 C
3.3 10 20 150
4.7 12.5 20 200
10 16 176 10 16 230 12.5 20 240
10
10 20 180 12.5 25 315 12.5 25 260
12.5 25 525 12.5 30 420
12.5 25 300
MINIATURE TYPES
22
16 25 570 16 25 470
33 16 20 600 16 25 600 18 31.5 560
16 25 660 16 35.5 650
47 16 25 700 16 25 630 16 31.5 720 18 31.5 620
18 25 720 18 35.5 700
16 31.5 16 31.5 800
56 740 16 40 740
18 25 18 25 800
16 35.5 16 35.5 900 16 45 820
68 16 31.5 1100 810
18 25 18 31.5 900 18 40 900
16 40 960 16 40 1115 16 50 1000

82 16 35.5 1150 18 31.5 1115
18 31.5 900 18 40 1000
18 35.5 1200
16 50 1250
16 40 16 40 1100
100 18 35.5 1200 1100 18 45 1250
18 35.5 18 35.5 1200 20 41 1250
16 50 1250 16 50 1500
120 18 40 1270 22 45 1370
18 40 1200 18 40 1500
150 20 41 1380 20 41 1600
109

RP Series Low Impedance Long Life Solvent Proof
High reliability long life(10000 hours)

Operating temperature 55 ~ +105 C
Enabled high ripple current by a reduction of impedance
at high frequency
Ideally suited for use in switching power supply, main board

WV 6.3 10 16 25 35 50
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.10
Low temperature characteristics WV 6.3 10 16 ~ 25 35 ~ 50

(Impedance ratio at 120Hz) Z-55 C/Z+20 C 3 3 3 3
D D 5, 6.3 D 8 D 10 D 12.5
Life time 4000 hours 6000 hours 7000 hours 10000 hours
DRAWING Unit : mm

D 0.5 max.
D 5 6.3 8 10 12.5 16 18
P 0.5
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
d 0.5 0.5 0.6 0.6 0.6 0.8 0.8
1.5 2.0
Safety vent ( 6.3 up)

Frequency
F
~ 33 0.40 0.65 0.82 0.91 1.00

39 ~ 270 0.50 0.70 0.84 0.92 1.00
330 ~ 680 0.55 0.75 0.86 0.93 1.00
820 ~ 1800 0.60 0.80 0.88 0.94 1.00
2200 ~ 0.70 0.85 0.90 0.95 1.00
110
RP series

WV 6.3 10 16
Impedance Ripple Impedance Ripple Impedance Ripple

Item
current current current
D L (Ω)max. D L (Ω)max. D L (Ω)max.
(mA rms) (mA rms) (mA rms)
(mm) 20 C (mm) 20 C (mm) 20 C
105 C 105 C 105 C
47 5 11 0.65 180
68 5 11 0.65 180 6.3 11 0.30 280
100 5 11 0.65 180 5 11 0.65 180 6.3 11 0.30 280
150 5 11 0.65 280 6.3 11 0.30 280 6.3 11 0.30 280
220 6.3 11 0.30 280 6.3 11 0.30 280 8 11.5 0.14 450
330 6.3 11 0.30 280 8 11.5 0.14 450 8 11.5 0.14 450
470 8 11.5 0.14 450 8 11.5 0.14 450 10 12.5 0.10 660
680 10 12.5 0.10 660 10 12.5 0.10 660 10 16 0.08 850
1000 10 12.5 0.10 660 10 16 0.08 850 10 20 0.054 1100
1500 10 20 0.054 1100 10 20 0.054 1100 12.5 20 0.050 1400
2200 12.5 20 0.050 1400 12.5 20 0.050 1400 12.5 25 0.038 1700
3300 12.5 20 0.050 1400 12.5 25 0.038 1700 16 25 0.030 2100
4700 16 25 0.030 2100 16 31.5 0.030 2100 16 25 0.025 2600
6800 16 25 0.030 2100 16 31.5 0.025 2600 16 35.5 0.022 3000
10000 16 31.5 0.025 2600 18 35.5 0.022 3000
15000 18 35.5 0.022 3000
WV 25 35 50
Impedance Ripple Impedance Ripple Impedance Ripple

Item
current current current
D L (Ω)max. D L (Ω)max. D L (Ω)max.
(mm) 20 C (mm) 20 C (mm) 20 C
105 C 105 C 105 C
1.0 5 11 3.5 40
2.2 5 11 3.0 55
3.3 5 11 2.6 65
MINIATURE TYPES
4.7 5 11 2.3 90
6.8 5 11 1.4 120
10 5 11 1.4 120
22 5 11 0.70 180 5 11 1.2 150
33 5 11 0.70 180 5 11 0.65 180 6.3 11 0.60 200
47 5 11 0.65 180 6.3 11 0.30 280 6.3 11 0.43 250
68 6.3 11 0.30 280 8 11.5 0.14 450 8 11.5 0.24 340
100 6.3 11 0.30 280 8 11.5 0.14 450 8 11.5 0.24 340
150 8 11.5 0.14 450 8 11.5 0.14 450 10 12.5 0.17 490
220 8 11.5 0.14 450 10 12.5 0.10 660 10 16 0.12 650
330 10 12.5 0.10 660 10 16 0.080 850 10 20 0.10 810
470 10 16 0.080 850 10 20 0.054 1100 12.5 20 0.085 1100
680 10 20 0.054 1100 12.5 20 0.050 1400 12.5 25 0.065 1200
1000 12.5 20 0.050 1400 12.5 25 0.038 1700 16 31.5 0.043 1600
1500 16 25 0.030 1400 16 31.5 0.030 2100 16 31.5 0.038 2000
2200 16 25 0.030 2100 16 31.5 0.025 2600 18 35.5 0.034 2300
3300 16 31.5 0.025 2600 18 35.5 0.022 3000
4700 18 35.5 0.022 3000
111
High ripple current,

WF Extremely Low Impedance Series Low Impedance Long Life Solvent Proof
Operating temperature range of 40 ~ +105 C

For E-meter

WV 6.3 10 16 25 35 50 63 100
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
Low temperature characteristics WV 6.3 10 16 25 ~ 100

(Impedance ratio at 120Hz) Z-40 C/Z+20 C 8 6 4 3
D D = 5, 6.3 D = 8, 10 D 12.5
DRAWING Unit : mm

D 0.5 max.
D 5 6.3 8 10 12.5 16 18
P 0.5
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
d 0.5 0.5 0.6 0.6 0.6 0.8 0.8
1.5 2.0

Frequency
F
~ 33 0.40 0.65 0.82 0.91 1.00

39 ~ 270 0.50 0.70 0.84 0.92 1.00
330 ~ 680 0.55 0.75 0.86 0.93 1.00
820 ~ 1800 0.60 0.80 0.88 0.94 1.00
2200 ~ 0.70 0.85 0.90 0.95 1.00
112
WF series

WV 6.3 10 16 25
Item Impedance Ripple Impedance Ripple Impedance Ripple Impedance Ripple

(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C
33 5 11 0.90 150
47 5 11 0.90 150 5 11 0.90 150
100 5 11 0.90 150 5 11 0.90 150 6.3 11 0.40 250 6.3 11 0.40 250
220 6.3 11 0.40 250 6.3 11 0.40 250 8 11.5 0.25 400 8 11.5 0.25 400
330 6.3 11 0.40 250 8 11.5 0.25 400 8 11.5 0.25 400 10 12.5 0.16 580
470 8 11.5 0.25 400 8 11.5 0.25 400 10 12.5 0.16 580 10 16 0.120 770
1000 10 12.5 0.16 580 10 16 0.120 770 10 20 0.078 1050 12.5 20 0.062 1300
2200 12.5 20 0.062 1300 12.5 20 0.062 1300 12.5 25 0.048 1650 16 25 0.034 1850
3300 12.5 20 0.062 1300 12.5 25 0.048 1650 16 25 0.034 1850 16 31.5 0.029 2000
4700 16 25 0.034 1850 16 25 0.034 1850 16 31.5 0.029 2000 18 35.5 0.025 2200
6800 16 25 0.034 1850 16 31.5 0.029 2000 18 35.5 0.025 2200
10000 16 31.5 0.029 2000 18 35.5 0.025 2200
15000 18 35.5 0.025 2200
WV 35 50 63 100

(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C
1.0 5 11 4.0 50 5 11 4.5 20

2.2 5 11 2.5 55 5 11 3.0 30
3.3 5 11 2.2 65 5 11 2.7 40
4.7 5 11 1.9 88 5 11 2.5 65
10 5 11 1.5 100 5 11 2.3 87 6.3 11 1.2 140
22 5 11 0.9 150 6.3 11 1.30 140 8 11.5 0.63 160
MINIATURE TYPES
33 5 11 0.90 150 6.3 11 0.40 250 6.3 11 1.20 140 10 12.5 0.43 230
10 12.5 0.43 230
47 6.3 11 0.4 250 6.3 11 0.4 400 8 11.5 0.63 210
10 16 0.31 290
12.5 16 0.23
100 8 11.5 0.25 400 8 11.5 0.25 500 10 12.5 0.43 300 750
12.5 20 0.16
220 10 12.5 0.16 580 10 16 0.12 770 10 25 0.210 520 16 25 0.073 900
330 10 16 0.120 770 10 20 0.08 1050 12.5 20 0.160 660 16 25 0.073 900
390 10 20 0.095 900 10 20 0.075 1170 12.5 25 0.140 700 12.5 34.5 0.073 1650
470 10 20 0.078 1050 12.5 20 0.062 1300 12.5 25 0.120 750
1000 12.5 25 0.048 1650 16 25 0.034 1850 16 31.5 0.054 1390
2200 16 31.5 0.029 2000 18 35.5 0.025 2200
3300 18 35.5 0.025 2200
113
High Ripple Current

LK Series Low Impedance Solvent Proof
Enabled high ripple current by a reduction of impedance at high frequency

(2000 ~ 4000 hours for smaller case sizes as specified below)
WV 6.3 ~ 63 100
temperature range -55 ~ +105 C -40 ~ +105 C

WV 6.3 10 16 25 35 50 63 100
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
Low temperature characteristics Z-55 C / Z+20 C Z-25 C / Z+20 C

3 2
Load life Capacitance change Within 25% of the initial value
D D 5, 6.3 D 8 D 10 D 12.5
DRAWING Unit : mm

D 0.5 max.
D 5 6.3 8 10 12.5 16 18
P 0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L max. 15 min. 4 min. 1.5 2.0
Safety vent 6.3 up)

Frequency
F
~ 33 0.32 0.60 0.80 0.90 1.00

39 ~ 270 0.40 0.63 0.82 0.91 1.00
330 ~ 680 0.45 0.67 0.84 0.92 1.00
820 ~ 1800 0.50 0.70 0.86 0.93 1.00
2200 ~ 0.60 0.75 0.88 0.94 1.00
114
LK series

WV 6.3 10 16 25

(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C
33 5 11 0.800 200
47 5 11 0.800 200 5 11 0.550 200
100 5 11 0.850 200 5 11 0.600 200 8 11.5 0.350 550 8 11.5 0.240 550
150 8 11.5 0.490 550 8 11.5 0.350 550 8 11.5 0.240 550 10 12.5 0.160 927
220 8 11.5 0.300 550 8 11.5 0.240 550 10 12.5 0.160 927 10 12.5 0.130 927
330 8 11.5 0.240 550 10 12.5 0.160 927 10 12.5 0.130 927 10 16 0.095 1100
470 10 12.5 0.140 927 10 12.5 0.130 927 10 16 0.095 1100 10 20 0.075 1280
680 10 16 0.110 1100 10 16 0.095 1100 10 20 0.075 1280 10 25 0.055 1495
1000 10 20 0.075 1280 10 20 0.075 1280 10 25 0.055 1495 12.5 25 0.043 2100
1500 10 25 0.055 1495 10 25 0.055 1495 12.5 25 0.043 2100 16 25 0.034 2607
2200 12.5 25 0.043 2100 12.5 25 0.043 2100 12.5 30 0.034 2480 16 31.5 0.032 2840
3300 12.5 30 0.034 2480 16 25 0.034 2607 16 31.5 0.032 2840 16 35.5 0.029 3017
4700 16 31.5 0.032 2840 16 31.5 0.032 2840 16 35.5 0.029 3017 18 40 0.027 3379
6800 16 35.5 0.029 3017 16 35.5 0.029 3017 18 40 0.027 3379
WV 35 50 63 100

(mm) 20 C (mm) 20 C (mm) 20 C (mm) 20 C

105 C 105 C 105 C 105 C
1.0 5 11 4.00 36
2.2 5 11 3.50 54 5 11 5.00 38
3.3 5 11 3.00 66 5 11 5.00 44
4.7 5 11 2.20 74 5 11 5.00 53
10 5 11 2.000 115 5 11 1.06 135 6.3 11 2.00 89
MINIATURE TYPES
22 5 11 2.000 200 5 11 1.800 160 6.3 11 0.520 215 8 11.5 1.200 159
33 5 11 1.500 200 6.3 11 1.200 285 8 11.5 0.350 320 10 12.5 0.800 221
47 8 11.5 0.700 550 8 11.5 0.700 550 8 11.5 0.250 365 10 16 0.600 350
100 10 12.5 0.200 927 10 12.5 0.200 927 10 20 0.120 750 12.5 20 0.300 405
150 10 12.5 0.160 927 10 16 0.120 1100 10 25 0.090 950 12.5 25 0.250 541
220 10 16 0.120 1100 10 20 0.095 1280 12.5 20 0.065 1140 16 25 0.150 885
330 10 20 0.095 1280 10 25 0.075 1495 12.5 25 0.049 1420 16 31.5 0.100 991
470 10 25 0.075 1495 12.5 25 0.055 2100 16 25 0.042 1700 18 40 0.068 1401
680 12.5 25 0.055 2100 16 25 0.043 2770 16 31.5 0.032 2050
1000 12.5 30 0.043 2480 16 31.5 0.034 2840 18 35.5 0.029 2280
1500 16 31.5 0.034 2840 16 35.5 0.032 3017
2200 16 35.5 0.032 3017 18 40 0.029 3379
3300 18 40 0.029 3379
115
High Ripple Current

MK Series Low Impedance Solvent Proof
Ripple current compared with LK series


WV 6.3 10 16 25 35 50 63 100
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.10 0.08 0.08

3 2
Load life Capacitance change Within 25% of the initial value
D D = 5, 6.3 D=8 D 10
DRAWING Unit : mm

D 0.5 max.
D 5 6.3 8 10 12.5 16 18
P 0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5

d 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L max. 15 min. 4 min. 1.5 2.0

Frequency
F
~ 33 0.40 0.65 0.82 0.94 1.00

39 ~ 270 0.50 0.70 0.84 0.96 1.00
330 ~ 680 0.55 0.75 0.86 0.96 1.00
820 ~ 1800 0.60 0.80 0.88 0.97 1.00
2200 ~ 0.70 0.85 0.90 0.97 1.00
116
MK series

WV 6.3 10 16 25
Impedance Ripple Impedance Ripple Impedance Ripple Impedance Ripple

Item
20 C 20 C 20 C 20 C
(mm) 105 C (mm) 105 C (mm) 105 C (mm) 105 C
10 5 11 1.000 250 5 11 1.000 250

22 5 11 0.525 250 5 11 0.525 250 5 11 1.000 250 5 11 0.525 250
33 5 11 0.525 250 5 11 0.525 250 5 11 0.525 250 5 11 0.525 250
47 5 11 0.450 250 5 11 0.450 250 5 11 0.450 250 5 11 0.450 250
5 11 0.450 250
100 5 11 0.450 250 5 11 0.450 250 6.3 11 0.225 405
6.3 11 0.300 405
150 6.3 11 0.300 405 6.3 11 0.300 405 6.3 11 0.225 405 8 11.5 0.160 760
220 6.3 11 0.225 405 6.3 11 0.225 405 8 11.5 0.108 760 8 11.5 0.160 760
330 6.3 11 0.225 405 8 11.5 0.175 760 8 11.5 0.108 760 10 12.5 0.098 1030
8 15 0.098 880 8 15 0.098 1030
390 8 11.5 0.108 550 8 11.5 0.108 760
10 12.5 0.098 880 10 12.5 0.098 1030
8 11.5 0.108 760 10 12.5 0.098 1030
470 8 11.5 0.108 760 8 11.5 0.108 760 8 15 0.098 1030 10 16 0.065 1430
10 12.5 0.088 1030 10 20 0.060 1500
8 15 0.098 880 8 15 0.098 880 8 20 0.088 1030 8 20 0.088 1430
560
10 12.5 0.098 880 10 12.5 0.098 880 10 16 0.088 1030 10 16 0.088 1430
8 15 0.098 10 16 0.065 1430
680 10 12.5 0.088 1030 1030 10 16 0.065 1430
10 12.5 0.088 10 20 0.050 1820
820 10 16 0.075 1030 10 12.5 0.088 1030 10 16 0.065 1450 10 20 0.050 2000
8 20 8 20 0.088 10 20 0.050 2100
0.088 1030 1500
1000 10 16 0.065 1430 10 12.5 10 16 0.065 10 25 0.045 2360
10 16 0.065 1430 10 20 0.050 1820 12.5 20 0.043 2600
1200 10 16 0.065 1820 12.5 20 0.043 2650
10 25 12.5 25 0.029 2770
1500 10 20 0.050 1820 10 20 0.050 1820 0.043 2360
12.5 20 16 20 0.024 2880
1800 10 20 0.050 1820 12.5 20 0.043 2000 12.5 25 0.029 2450 12.5 25 0.029 2900
10 20 0.05 1820
2200 12.5 20 0.043 2360 10 25 0.048 10 30 12.5 25 0.029 3000
2360 0.029 2770
MINIATURE TYPES
12.5 20 0.043 12.5 25 16 25 0.024 3114
12.5 25
3300 12.5 20 0.040 2360 0.029 3140 16 25 0.024 3200 16 31.5 0.024 3312
16 20
4700 16 25 0.024 3114 16 25 0.024 3200 16 31.5 0.024 3312 18 35.5 0.022 3420
6800 16 25 0.024 3114 16 31.5 0.024 3312 18 35.5 0.022 3420
10000 16 31.5 0.024 3312 18 35.5 0.022 3420
15000 18 35.5 0.022 3420
117
MK series

WV 35 50 63 100
Impedance Ripple Impedance Ripple Impedance Ripple Impedance Ripple

Item
20 C 20 C 20 C 20 C
(mm) 105 C (mm) 105 C (mm) 105 C (mm) 105 C
0.22 5 11 5.00 250

0.47 5 11 4.00 250
1.0 5 11 3.00 250
2.2 5 11 3.00 250 5 11 3.000 125
3.3 5 11 1.50 250 5 11 2.000 165 5 11 2.000 125
4.7 5 11 0.525 250 5 11 1.50 250 5 11 2.000 165 5 11 2.000 125
10 5 11 0.525 250 5 11 1.000 250 5 11 0.800 165 6.3 11 1.200 205
22 5 11 0.525 250 5 11 0.500 250 6.3 11 0.500 265 8 11.5 0.300 355
33 5 11 0.450 250 6.3 11 0.300 405 6.3 11 0.500 265 10 12.5 0.250 450
8 15 0.200 500
47 6.3 11 0.300 405 6.3 11 0.300 405 8 11.5 0.300 500
10 16 0.200 580
56 6.3 11 0.300 405 8 11.5 0.160 580 10 12.5 0.160 680 10 16 0.160 750
8 11.5 0.160 760 10 20 0.150 800
100 8 11.5 0.160 760 10 16 0.100 945
8 15 0.108 770 12.5 20 0.100 1045
150 8 11.5 0.160 760 10 12.5 0.088 1030 10 20 0.080 1100 12.5 25 0.080 1195
8 15 0.098 1030
220 10 16 0.065 1430 10 25 0.070 1300 16 25 0.060 1600
10 12.5 0.088 1030
330 10 16 0.065 1430 10 20 0.050 1820 12.5 20 0.050 1495 16 31.5 0.040 1750
390 8 20 0.088 1430 10 20 0.050 1820 12.5 25 0.038 1600 16 31.5 0.040 1750
8 20 0.088
1430
470 10 16 0.065 12.5 20 0.043 2360 16 20 0.035 1990 18 40 0.030 2060
10 20 0.050 1820
10 20 0.050 1820
680 12.5 25 0.029 2770 16 25 0.030 2780
12.5 20 0.043 2360
12.5 20 0.043 2500
1000 16 25 0.027 3114 16 35.5 0.020 2835
12.5 25 0.029 2770
12.5 25 0.029 2770
1500 16 20 0.027 2880 16 31.5 0.024 3312
16 25 0.024 3114
2200 16 31.5 0.024 3312 18 35.5 0.022 3420
3300 18 35.5 0.022 3420
118
High Ripple Current

MQ Series Low Impedance Solvent Proof
High Ripple current with MK series


WV 6.3 10 16 25 35 50
(at 120Hz, 20 C)
tan 0.22 0.19 0.16 0.14 0.12 0.1

3 2
Load life
D D 5, 6.3 D 8 D 10 D 12.5
DRAWING Unit : mm
MINIATURE TYPES
D 0.5 max.
D 5 6.3 8 10 12.5 16
P 0.5 P 2.0 2.5 3.5 5.0 5.0 7.5

d 0.5 0.5 0.6 0.6 0.6 0.8
L max. 15 min. 4 min. 1.5 2.0

Frequency
F
~ 33 0.30 0.65 0.82 0.94 1.00

47 ~ 270 0.40 0.70 0.84 0.96 1.00
330 ~ 680 0.45 0.75 0.86 0.96 1.00
820 ~ 1800 0.50 0.80 0.88 0.97 1.00
2200 ~ 0.60 0.85 0.90 0.97 1.00
119
2015-4장-02 2015.1.20 03:42 PM 페이지120 태산아이인쇄그룹(국) 2261-2488 2400DPI 175LPI
MQ series

WV 6.3 10 16
Item Impedance Ripple Impedance Ripple Impedance Ripple

ØD×L current ØD×L current ØD×L current
(Ω)max. (Ω)max. (Ω)max.
(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
μF 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
10 5 × 11 0.525 250
22 5 × 11 0.525 250 5 × 11 0.525 250 5 × 11 0.525 270
33 5 × 11 0.525 270 5 × 11 0.525 270 5 × 11 0.525 290
47 5 × 11 0.450 290 5 × 11 0.450 290 5 × 11 0.450 310
100 5 × 11 0.450 310 5 × 11 0.450 310 6.3 × 11 0.225 405
150 6.3 × 11 0.225 405 6.3 × 11 0.225 405 6.3 × 11 0.225 460
220 6.3 × 11 0.225 460 6.3 × 11 0.225 460 8 × 11.5 0.108 760
330 6.3 × 11 0.225 505 8 × 11.5 0.108 760 8 × 11.5 0.108 950
470 8 × 11.5 0.108 950 8 × 11.5 0.108 950 10 × 12.5 0.088 1280
680 10 × 12.5 0.088 1280 10 × 12.5 0.088 1280 10 × 16 0.065 1785
1000 10 × 16 0.065 1785 10 × 16 0.065 1785 10 × 20 0.050 2270
1200 10 × 16 0.065 2200
1500 10 × 20 0.050 2270 10 × 20 0.050 2270 12.5 × 20 0.043 2950
2200 12.5 × 20 0.043 2950 12.5 × 20 0.043 2950 12.5 × 25 0.029 3460
WV 25 35 50

ØD×L (Ω)max. current ØD×L (Ω)max. current ØD×L (Ω)max. current
(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
4.7 5 × 11 0.525 250 5 × 11 0.525 250 5 × 11 1.50 270
10 5 × 11 0.525 250 5 × 11 0.525 270 5 × 11 0.750 290
22 5 × 11 0.525 270 5 × 11 0.525 290 5 × 11 0.390 310
33 5 × 11 0.525 290 5 × 11 0.450 310 6.3 × 11 0.255 405
47 5 × 11 0.450 310 6.3 × 11 0.225 460 6.3 × 11 0.210 460
100 6.3 × 11 0.225 460 8 × 11.5 0.108 760 8 × 11.5 0.108 950
150 8 × 11.5 0.108 760 8 × 11.5 0.108 950 10 × 12.5 0.088 1280
220 8 × 11.5 0.108 950 10 × 12.5 0.088 1280 10 × 16 0.065 1785
330 10 × 12.5 0.088 1280 10 × 16 0.065 1785 10 × 20 0.050 2270
470 10 × 16 0.065 1785 10 × 20 0.050 2270 12.5 × 20 0.043 2950
680 10 × 20 0.060 2270 12.5 × 20 0.043 2950 12.5 × 25 0.029 3460
1000 12.5 × 20 0.060 2950 12.5 × 25 0.029 3460 16 × 25 0.027 3890
1200 12.5 × 20 0.043 3100
1500 16 × 20 0.024 3600 16 × 25 0.024 3890
2200 16 × 25 0.024 3890
120
MZ Ultra Low Impedance

Series Low Impedance Miniaturized Solvent Proof
・Low impedance compared with MK series

・Enabled high ripple current by a reduction of impedance at high frequency
・High reliability withstanding 5000 hours load life at 105°
C
I = 0.01CV or 3μA whichever is greater (after 2 minutes)
I = 0.03CV or 4μA whichever is greater (after 1 minute)
Capacitance > 1000μF : tanδincreases by 0.02 for each 1000μF from below value.
WV 6.3 10 16 25 35 50 63 100
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08

C / Z+20°
C Z-25°
C / Z+20°
C
(Impedance ratio at 120Hz) 3 2
After an application of DC bias voltage plus the rated AC ripple current for 5000 hours at 105°
C.
ØD ØD = 5, 6.3 ØD = 8 ØD ≧ 10
C)
Insulating sleeve Ød±0.05 Tinned copper-ply wire
MINIATURE TYPES
ØD+0.5 max.
＋ ØD 5 6.3 8 10 12.5 16 18
－ P±0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L+βmax. 15 min. 4 min. β 1.5 2.0
Safety vent(Ø6.3 up)

Frequency 120Hz 1kHz 10kHz 50kHz 100kHz≦
μF
~ 33 0.42 0.70 0.90 0.95 1.00
47 ~ 270 0.50 0.73 0.92 0.96 1.00
330 ~ 680 0.55 0.77 0.94 0.97 1.00
1000 ~ 1500 0.60 0.80 0.96 0.98 1.00
2200 ~ 0.70 0.85 0.98 0.99 1.00
121
MZ series

WV 6.3 10 16 25

ØD×L (Ω)max. current ØD×L (Ω)max. current ØD×L (Ω)max. current ØD×L (Ω)max. current
(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
μF 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
4.7 5×11 0.35 250
10 5×11 0.35 250 5×11 0.35 250
22 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250
33 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250
47 5×11 0.30 250 5×11 0.30 250 5×11 0.30 250 5×11 0.30 250
100 5×11 0.30 250 5×11 0.30 250 6.3×11 0.15 405 6.3×11 0.15 405
150 6.3×11 0.15 405 6.3×11 0.15 405 6.3×11 0.15 405 8×11.5 0.10 760
220 6.3×11 0.15 405 6.3×11 0.15 405 8×11.5 0.072 760 8×11.5 0.10 760
330 6.3×11 0.15 405 8×11.5 0.12 760 8×11.5 0.072 760 10×12.5 0.08 1030
470 8×11.5 0.072 760 8×11.5 0.10 760 10×12.5 0.053 1030 10×16 0.038 1430
680 10×12.5 0.053 1030 10×12.5 0.053 1030 10×16 0.038 1430 10×20 0.027 1820
1000 10×12.5 0.053 1030 10×16 0.038 1430 10×20 0.027 1820 12.5×20 0.025 2360
1500 10×20 0.027 1820 10×20 0.027 1820 12.5×20 0.025 2360 16×20 0.020 3460
2200 12.5×20 0.025 2360 12.5×20 0.025 2360 12.5×25 0.018 2770 16×25 0.015 3460
3300 12.5×20 0.025 2360 12.5×25 0.024 2770 16×25 0.015 3460 16×31.5 0.015 3680
4700 16×25 0.015 3460 16×25 0.015 3460 16×31.5 0.015 3680 18×35.5 0.014 3800
6800 16×25 0.015 3460 16×31.5 0.015 3680 18×35.5 0.014 3800
10000 16×31.5 0.015 3680 18×35.5 0.014 3800
15000 18×35.5 0.014 3800
WV 35 50 63 100

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
0.47 5× 11 2.0 250
1.0 5× 11 2.0 250
2.2 5× 11 2.0 250 5× 11 2.0 125
3.3 5× 11 1.0 250 5× 11 2.0 165 5× 11 2.0 125
4.7 5 ×11 0.35 250 5× 11 1.0 250 5× 11 2.0 165 5× 11 2.0 125
10 5 ×11 0.35 250 5× 11 0.50 250 5× 11 0.45 165 6.3× 11 0.50 205
22 5 ×11 0.35 250 5× 11 0.4 250 6.3× 11 0.30 265 8× 11.5 0.30 355
33 5 ×11 0.30 250 6.3× 11 0.17 405 6.3× 11 0.30 265 10× 12.5 0.25 450
47 6.3 ×11 0.15 405 6.3× 11 0.14 405 8× 11.5 0.20 500 10× 16 0.20 580
100 8 ×11.5 0.072 760 8× 11.5 0.105 760 10× 16 0.10 945 12.5× 20 0.10 1045
150 8 ×11.5 0.072 760 10× 12.5 0.061 1030 10× 20 0.08 1100 12.5× 25 0.070 1195
220 10 ×12.5 0.065 1030 10× 16 0.038 1430 10× 25 0.07 1300 16× 25 0.060 1600
330 10 ×16 0.038 1430 10× 20 0.032 1820 12.5× 20 0.04 1495 16× 31.5 0.040 1750
470 10 ×20 0.027 1820 12.5× 20 0.025 2360 16× 20 0.035 1990 18× 40 0.030 2060
680 12.5 ×20 0.025 2360 12.5× 25 0.020 2770 16× 25 0.030 2780
1000 12.5 ×25 0.022 2770 16× 25 0.018 3460 16× 35.5 0.020 2835
1500 16 ×25 0.018 3460 16× 31.5 0.015 3680
2200 16 ×31.5 0.015 3680 18× 35.5 0.014 3800
3300 18 ×35.5 0.014 3800
122
MB Low Imp., High Ripple Current

・Ultra low impedance

C
・For SMPS, IP-Board, Adaptor, Noise Filter, Charger
・Complied to the RoHS directive, Halogen-Free
C
WV 6.3 10 16 25 35 50 63 100
tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
(at 120Hz, 20°C)
When rated Capacitance is over 1000μF, tanδshall be added 0.02 to the listed value with increase
of every 1000μF.
C/Z+20°
C Z-25°
C/Z+20°
C
C.
Load life Capacitance change Within ±25% of the initial value
tanδ Less than 200% of the specified value
ØD ØD = 5, 6.3 ØD = 8 ØD = 10 ØD ≧ 12
ØD 5 6.3 8 10 12.5 16 18
MINIATURE TYPES
ØD+0.5 max.
P±0.5
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
－
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
β 1.5 2.0
L+βmax. 15 min. 4 min.
Safety vent (Ø6.3 up)

μF
1 ~ 180 0.40 0.75 0.90 0.95 1.00
220 ~ 560 0.50 0.85 0.94 0.96 1.00
680 ~ 1800 0.60 0.87 0.95 0.97 1.00
2200 ~ 3900 0.75 0.90 0.95 0.97 1.00
4700 ~ 18000 0.85 0.95 0.98 0.99 1.00
123
MB series

WV 6.3 10 16 25

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
68 5×11 0.300 250
5×11 0.030 250
100
6.3×11 0.015 385
150 5×11 0.300 250 6.3×11 0.130 405
220 5× 11 0.300 250 6.3× 11 0.130 405 8× 11.5 0.072 760
6.3×11 0.130 405
330 10×12.5 0.053 1030
8×11.5 0.094 600
390 8×15 0.060 818
10×12.5 0.053 1030
470 6.3× 11 0.130 405 8×11.5 0.072 760
10×16 0.038 1430
560 8×11.5 0.075 1200 8×20 0.050 1260
10×16 0.038 1430
8×15 0.060 818
680 8×11.5 0.072 760 10×20 0.023 1820
10×12.5 0.053 1030 12.5×16 0.031 1452
820 8×11.5 0.072 760 10×12.5 0.053 1030 10×20 0.023 2000
8×15 0.060 818 8×20 0.050 1260 10×20 0.025 1900
1000 10×12.5 0.053 1030
10×16 0.038 1430 10×25 0.022 2150
10×16 0.038 1430
8×15 0.060 818
1200 8× 20 0.050 1260
10×12.5 0.053 1030
10×16 0.038 1430
1500 8×20 0.050 1260 10×20 0.023 1820 10×20 0.023 1820 12.5×20 0.021 2360
12.5×16 0.031 1452
10×16 0.038 1430
1800 10×25 0.022 2150 12.5×25 0.020 2770
12.5×16 0.031 1452
12.5×25 0.020 3000
2200 10×20 0.023 1820 10×25 0.022 2150 12.5×20 0.021 2360 16×20 0.021 3140
18×20 0.023 2860
2700 12.5×25 0.020 2770 18×25 0.018 3611
16×20 0.021 3140
3300 10× 25 0.022 2150 12.5× 20 0.021 2360 16×25 0.019 3460
18×20 0.023 2826
12.5×35 0.017 3400
3900 12.5× 20 0.021 2360 12.5× 25 0.020 2770
18×25 0.018 3611
16×20 0.021 3140
4700 12.5× 25 0.020 2770 16×25 0.019 3460
18×20 0.023 2826
12.5×30 0.018 3290
16× 25 0.019 3460
5600 16×20 0.021 3140 16×31.5 0.013 3680
18×20 0.023 2826 18×25 0.018 3611
6800 16×25 0.019 3460 16×31.5 0.013 3680
16×31.5 0.013 3680
8200
18×25 0.018 3611
124
MB series

WV 35 50 63 100

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
1.0 5×11 2.500 53
2.2 5×11 2.500 56
3.3 5×11 2.300 60 5×11 2.000 125
4.7 5×11 1.500 82 5×11 2.000 125
10 5×11 1.000 250 5×11 0.45 165 6.3×11 0.500 205
22 5×11 0.300 250 8×11.5 0.030 355
27 5×11 0.300 250
33 6.3×11 0.300 265 10×12.5 0.250 450
47 5×11 0.300 250 6.3 11 0.140 350 8×11.5 0.200 500 10×16 0.200 580
56 6.3×11 0.140 385
68 10×12.5 0.160 600
100 6.3×11 0.130 405 8×11.5 0.072 724 10×16 0.100 945 12.5×20 0.100 1045
120 8×15 0.060 818
150 8×11.5 0.072 760 10×12.5 0.061 979 10×20 0.080 1100 12.5×25 0.070 1195
180 8×20 0.050 1260
220 10×12.5 0.053 1030 10×16 0.042 1370 10×25 0.070 1300 16×25 0.060 1600
270 8×15 0.060 818 12.5×16 0.042 1071
330 10×12.5 0.053 1030 10×20 0.030 1580 10×25 0.070 1300 16×31.5 0.040 1750
390 8×20 0.050 1260
10×16 0.038 1430 16×31.5 0.040 1750
470 12.5×20 0.027 2050 16×20 0.035 1990
12.5×16 0.031 1452 18×40 0.030 2060
560 10×20 0.023 1820 12.5×25 0.020 2410
10×20 0.023 1820
680 16×25 0.030 2780
10×25 0.022 2150
820 16×20 0.023 2730
MINIATURE TYPES
12.5×20 0.021 2360 16×25 0.021 3010
1000 16×35.5 0.020 2835
12.5×25 0.020 2770 18×20 0.022 2850
1200 12.5×25 0.020 2770 18×25 0.020 3140
16×20 0.021 3140
1500
18×20 0.023 2860
16×25 0.019 3460
1800
18×25 0.018 3611
16×25 0.019 3460
2200
16×31.5 0.013 3680
125
LZ Low Impedance, Long Life

Series Low Impedance Long Life Solvent Proof
・Operating temperature range of -40 ~ +105° C

・Enabled high ripple current by a reduction of impedance at high frequency range
C
(6000 / 8000 hours for as specified below)
I = 0.01CV or 3μA whichever is greater (after 2 minutes)
I = 0.03CV or 4μA whichever is greater (after 1 minute)
Dissipation factor max. Rated Voltage(V) 6.3 10 16 25 35 50
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16 0.14 0.12 0.10

C / Z+20°
C Z-25°
C / Z+20°
C
C.
ØD ØD = 5, 6.3 ØD = 8 ØD ≥ 10

ØD+0.5 max.
＋ ØD 5 6.3 8 10 12.5 16 18
－ P±0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L+βmax. 15 min. 4 min. β 1.5 2.0

Frequency 120Hz 1kHz 10kHz 50kHz 100kHz
μF
~ 33 0.32 0.60 0.80 0.90 1.00
39 ~ 270 0.40 0.63 0.82 0.91 1.00
330 ~ 680 0.45 0.67 0.84 0.92 1.00
820 ~ 1800 0.50 0.70 0.86 0.93 1.00
2200 ~ 0.60 0.75 0.88 0.94 1.00
126
LZ series
WV 6.3 10 16
(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
47 5 × 11 0.600 300 5 × 11 0.600 300 5 × 11 0.600 300
100 5 × 11 0.600 345 5 × 11 0.600 345 6.3 × 11 0.300 345
150 6.3 × 11 0.300 345 6.3 × 11 0.300 345 6.3 × 11 0.300 540
220 6.3 × 11 0.300 345 6.3 × 11 0.300 345 8 × 11.5 0.200 540
330 6.3 × 11 0.300 540 8 × 11.5 0.250 608 8 × 11.5 0.200 945
470 8 × 11.5 0.140 540 8 × 11.5 0.200 630 10 × 12.5 0.105 945
8 × 20 0.105 945
680 10 × 12.5 0.105 945 10 × 12.5 0.105 945
10 × 16 0.075 1250
820 10 × 12.5 0.105 945 10 × 16 0.075 945 10 × 20 0.054 1760
8 × 20 0.105 945 8 × 20 0.075 1250
10 × 12.5 0.105 945
1000 10 × 16 0.075 1250
10 × 16 0.075 1250 10 × 20 0.054 1760
10 × 20 0.054 1650
1200 10 × 16 0.075 1500 10 × 16 0.075 1760 10 × 20 0.054 1960
1500 10 × 20 0.054 1760 10 × 20 0.054 1760 12.5 × 20 0.050 1960
1800 10 × 20 0.054 1760 10 × 20 0.054 1760 12.5 × 20 0.050 2250
2200 12.5 × 20 0.050 1960 12.5 × 20 0.050 1960 12.5 × 25 0.040 2480
2700 12.5 × 20 0.050 2250 12.5 × 25 0.040 2250 12.5 × 25 0.040 2900
3300 12.5 × 20 0.050 2480 12.5 × 25 0.040 2480 16 × 25 0.030 3250
3900 12.5 × 25 0.040 2480 16 × 25 0.030 2480 16 × 25 0.030 3570
4700 16 × 25 0.030 3250 16 × 25 0.030 3250 16 × 31.5 0.027 3630
5600 16 × 25 0.030 3570 16 × 25 0.030 3570
6800 16 × 25 0.030 3630 16 × 31.5 0.027 3630
8200 16 × 31.5 0.027 3700 18 × 35.5 0.025 3700
WV 25 35 50

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
10 5× 11 3.000 160
22 5× 11 1.800 240
33 5× 11 1.800 292
47 6.3× 11 0.450 345 6.3× 11 1.000 450
56 6.3× 11 0.450 345 6.3× 11 0.700 450
68 6.3× 11 0.300 345 6.3× 11 0.450 345 8× 11.5 0.500 490
MINIATURE TYPES
6.3× 11 0.350 500
100 6.3× 11 0.300 345 8× 11.5 0.300 724
8× 11.5 0.300 540
120 6.3× 11 0.300 345 8× 11.5 0.250 540 8× 11.5 0.200 950
150 8× 11.5 0.250 345 8× 11.5 0.250 945 10× 12.5 0.120 979
345 8× 20 0.120 1200
180 8× 11.5 0.200 8× 11.5 0.190 945
10× 12.5 0.120 1190
8× 11.5 0.190 945 8× 20 0.120 1370
220 8× 11.5 0.160 345
10× 12.5 0.105 945 10× 16 0.075 1370
8× 15 0.120 945
270 10× 12.5 0.105 945 10× 20 0.064 1580
10× 16 0.085 1250
330 10× 12.5 0.105 945 10× 16 0.085 1330 10× 20 0.064 1870
8× 15 0.105 1250 0.054
390 10× 20 1500 10× 20 0.064 2050
10× 12.5 0.105 1250
8× 20 0.095 1430
470 10× 16 0.075 1330 10× 16 0.085 1600 12.5× 20 0.050 2050
10× 20 0.054 1760
8× 20 0.075 12.5× 20
560 1700 0.050 1960 12.5× 25 0.040 2410
10× 20 0.054
10× 16 0.075 10× 20 0.054 1850
680 1760 12.5× 20 12.5× 25 0.040 2410
10× 20 0.054 0.050 2250
10× 25
10× 20 0.054
820 2300 12.5× 25 0.040 2350 16× 20 0.040 2730
12.5× 20 0.050
1000 12.5× 20 0.050 2350 12.5× 25 0.040 2480 16× 25 0.036 3010
1200 12.5× 20 0.050 2480 16× 20 0.040 2900
1500 16× 20 0.040 2480 16× 25 0.030 3250
1800 16× 20 0.040 2900 16× 25 0.030 3570
12.5× 30 0.040 2900
2200 16× 31.5 0.027 3630
16× 25 0.030 3250
2700 16× 25 0.030 3570
3300 16× 31.5 0.027 3630
127
ML Ultra Low Impedance, Long Life

・Long Life compared with MZ series

・Enabled high ripple current by a reduction of impedance at high frequency
C
(6000/8000 hours for as specified below)
I = 0.01CV or 3μ
I = 0.03CV or 4μ
A whichever is greater (after 1 minute)
WV 6.3 10 16 25 35 50 63 100
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08

C / Z+20°
C Z-25°
C / Z+20°
C
C.
ØD ØD = 5, 6.3 ØD = 8 ØD ≧ 10

ØD+0.5 max.
＋ ØD 5 6.3 8 10 12.5 16 18
－ P±0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L+βmax. 15 min. 4 min. β 1.5 2.0

μF
~ 33 0.42 0.70 0.90 0.95 1.00
39 ~ 270 0.50 0.73 0.92 0.96 1.00
330 ~ 680 0.55 0.77 0.94 0.97 1.00
820 ~ 1800 0.60 0.80 0.96 0.98 1.00
2200 ~ 0.70 0.85 0.98 0.99 1.00
128
ML series

WV 6.3 10 16 25

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
10 5×11 0.35 250 5×11 0.35 250
22 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250
33 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250 5×11 0.35 250
47 5×11 0.30 250 5×11 0.30 250 5×11 0.30 250 5×11 0.30 250
100 5×11 0.30 250 5×11 0.30 250 6.3×11 0.25 405 6.3×11 0.20 405
150 6.3×11 0.15 405 6.3×11 0.15 405 6.3×11 0.20 405 8×11.5 0.14 760
220 6.3×11 0.15 405 6.3×11 0.15 405 8×11.5 0.15 760 8×11.5 0.12 760
330 6.3×11 0.15 405 8×11.5 0.08 760 8×11.5 0.10 760 10×12.5 0.053 1030
390 6.3×11 0.15 405 8×11.5 0.072 760 8×11.5 0.10 760 8×15 0.072 1250
470 8×11.5 0.072 760 8×11.5 0.072 760 10×12.5 0.053 1030 10×16 0.038 1430
560 8×11.5 0.072 630 10×12.5 0.053 650 10×12.5 0.053 1100 8×20 0.072 1800
680 10×12.5 0.053 1030 10×12.5 0.053 1030 10×16 0.038 1430 10×20 0.027 1820
1000 10×12.5 0.053 1030 10×16 0.038 1430 10×20 0.027 1820 12.5×20 0.025 2360
1500 10×20 0.027 1820 10×20 0.027 1820 12.5×20 0.025 2360 16×20 0.015 3460
2200 12.5×20 0.025 2360 12.5×20 0.025 2360 12.5×25 0.018 2770 16×25 0.015 3460
3300 12.5×20 0.025 2360 12.5×25 0.022 2770 16×25 0.015 3460 16×31.5 0.015 3680
4700 16×25 0.015 3460 16×25 0.015 3460 16×31.5 0.015 3680
6800 16×25 0.015 3460 16×31.5 0.015 3680
10000 16×31.5 0.015 3680 18×35.5 0.014 3800
WV 35 50 63 100

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
MINIATURE TYPES
10 5 ×11 0.55 250 5×11 0.60 250 5×11 0.45 165 6.3× 11 0.50 205
22 5 ×11 0.50 250 5×11 0.45 250 6.3×11 0.37 265 8× 11.5 0.30 355
33 5 ×11 0.45 250 6.3×11 0.25 405 6.3×11 0.37 265 10× 12.5 0.25 450
47 6.3 ×11 0.30 405 6.3×11 0.20 405 8×11.5 0.20 500 10× 16 0.20 580
56 6.3 ×11 0.20 405 6.3×11 0.20 405 8×11.5 0.17 540 10× 16 0.20 630
68 8 ×11.5 0.10 540 8×11.5 0.10 540 10×12.5 0.15 760 8× 20 0.25 700
10× 20 0.18 800
100 8 ×11.5 0.10 760 8×11.5 0.10 760 10×16 0.10 945
12.5× 20 0.10 1045
8×20 0.120
150 8 ×11.5 0.10 760 10×12.5 0.061 1030 1200 12.5× 25 0.080 1195
10×20 0.080
220 10 ×12.5 0.053 1030 10×16 0.038 1430 10×25 0.070 1300 16× 25 0.060 1600
330 10 ×16 0.038 1430 10×20 0.032 1820 12.5×20 0.040 1495 16× 31.5 0.040 1750
8 ×20 0.038 1600
470 12.5×20 0.025 2360 16×20 0.037 1990 18× 40 0.030 2060
10 ×20 0.027 1820
680 12.5 ×20 0.025 2360 12.5×25 0.020 2770 16×25 0.030 2780
1000 12.5 ×25 0.022 2770 16×25 0.018 3460 16×35.5 0.020 2835
1500 16 ×25 0.018 3460 16×31.5 0.015 3680
2200 16 ×31.5 0.015 3680 18×40 0.02 3500
129

Upgrade
MN High Ripple Current,

Ultra Low Impedance Series Low Impedance Solvent Proof
・High ripple current compared with MZ series

・Enabled high ripple current by a reduction of impedance at high frequency range
C
(3000 hours for smaller case sizes as specified below)
I = 0.01CV or 3μ
I = 0.03CV or 4μ
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16 0.14 0.12 0.10

C / Z+20°
C Z-25°
C / Z+20°
C

voltage for 5000 hours at 105° C) ØD ØD = 8 ØD = 10

ØD+0.5 max.
＋ ØD 8 10
－ P±0.5 P 3.5 5.0
Ød 0.6 0.6

β 1.5 2.0
Safety vent

μF
~ 220 0.50 0.73 0.92 0.96 1.00
390 ~ 680 0.55 0.77 0.94 0.97 1.00
820 ~ 1800 0.60 0.80 0.96 0.98 1.00
2200 ~ 0.70 0.85 0.98 0.99 1.00
130
MN series

WV 6.3 10 16

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
470 8 × 11.5 0.036 1140
8 × 15 0.028 1490
680 8 × 11.5 0.036 1254
10 × 12.5 0.026 1540
820 8 × 11.5 0.036 1140
8 × 15 0.028 1639 8 × 20 0.021 1870
1000
10 × 12.5 0.026 1694 10 × 16 0.019 2000
1200 8 × 15 0.028 1490
8 × 20 0.016 1950 8 × 20 0.021 1870
1500 10 × 20 0.013 2550
10 × 12.5 0.026 1540 10 × 16 0.019 2000
8 × 20 0.021 1870
1800 10 × 20 0.013 2550 10 × 25 0.015 2800
10 × 16 0.019 2000
2200 10 × 20 0.013 2550 10 × 25 0.012 2800
3300 10 × 25 0.012 2800
WV 25 35 50

(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
100 8 × 11.5 0.096 1195
120 8 × 15 0.080 1714
150 10 × 12.5 0.083 1773
180 8 × 20 0.065 2077
220 8 × 11.5 0.036 1140 8 × 11.5 0.073 1559 10 × 16 0.057 2184
270 8 × 15 0.059 2255 10 × 20 0.042 2554
330 10 × 12.5 0.053 2409 10 × 25 0.037 2889
MINIATURE TYPES
390 8 × 15 0.028 1490 8 × 20 0.041 2618
470 10 × 12.5 0.026 1540 10 × 16 0.038 2805
560 8 × 20 0.019 1870 10 × 20 0.028 2880
680 10 × 16 0.019 2000 10 × 25 0.024 3150
820 10 × 20 0.013 2550
1000 10 × 25 0.015 2800
131
MD High Ripple Current,

Ultra Low Impedance Series Low Impedance Solvent Proof
・High ripple current compared with MZ series

・Enabled ripple current with extremely low impedance
at high frequency range
C
I = 0.01CV or 3μ
I = 0.03CV or 4μ
WV 6.3 10 16
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16
Low temperature characteristics WV 6.3 10 16

C / Z+20°
C 3 3 3
C.
C)
● DRAWING (See page 123) Unit : mm

WV 6.3 10 16
Item Impedance Ripple current Impedance Ripple current Impedance Ripple current
ØD×L (Ω)max. (mA rms) ØD×L (Ω)max. (mA rms) ØD×L (Ω)max. (mA rms)
(mm) 20°
C 105°C (mm) 20°
C 105°C (mm) 20°
C 105°C
470 8 × 11.5 0.021 1340

8 × 15 0.020 1850
680 8 × 11.5 0.021 1340
10 × 12.5 0.016 1960
820 8 × 11.5 0.021 1340
8 × 15 0.020 1850 8 × 20 0.013 2350
1000
10 × 12.5 0.016 1960 10 × 16 0.013 2460
1200 8 × 15 0.020 1850
8 × 20 0.013 2350
1500 10 × 12.5 0.016 1960 10 × 20 0.011 2770
10 × 16 0.013 2460
1800 8 × 20 0.013 2460 10 × 20 0.011 2770 10 × 25 0.011 3230
2200 10 × 20 0.011 2770 10 × 25 0.09 3230
3300 10 × 25 0.09 3230

μF
~ 820 0.55 0.77 0.94 0.97 1.00
1000 ~ 1800 0.60 0.80 0.96 0.98 1.00
2200 ~ 0.70 0.85 0.98 0.99 1.00
132

Upgrade
SJ For PSU, Long Life

Series Long Life

C
・Suitable for CFL, adapter and power supply
Leakage current max. I = 0.02CV+25μA (after 5 minutes)
C
Dissipation factor max. Rated Voltage(V) 420 450 500
(at 120Hz, 20°C) tanδ 0.20 0.20 0.20
Low temperature characteristics WV 420 450 500

(Impedance ratio at 120Hz) Z(-25°
C) / Z(+20°
C) 6 6 6

Shelf life (at 85°
C)
ØD 16 18
ØD+0.5 max.
＋
P 7.5 7.5
－ P±0.5 Ød 0.8 0.8
L≤40mm 2.0
β
L+βmax. 15 min. 4 min. L≻40mm 3.0
Safety vent
MINIATURE TYPES
WV 420 450 500
μF
47 16 × 35.5 360
56 16 × 40 420
16 × 40
16 × 35.5 560
68 16 × 31.5 550 16 × 45 490
18 × 31.5 560 18 × 40
16 × 40 630
82 16 × 31.5 580 16 × 50 520
18 × 31.5 630
16 × 40 750
100 16 × 40 725 16 × 50 700
18 × 35.5 750
120 16 × 45 850 16 × 50 800
150 16 × 50 870

C, 120Hz

Frequency 120Hz 1kHz 10kHz 50kHz, 100kHz
WV
420 ~ 500V 1.00 1.40 1.50 2.00
133
LY Miniature, Long Life, For LED Lighting

・Miniature, long life

・For LED Lighting
C
C
I = 0.01CV or 3μA wichever is greater (after 2 minutes)
I = 0.03CV or 4μA wichever is greater (after 1 minute)
C
Dissipation factor max. WV 10 16 25 35 50

(at 120Hz, 20°C) tanδ 0.45 0.35 0.30 0.22 0.19
Low temperature characteristics WV 10 16 25 35 50

C/Z+20°
C 8 6 4 4 3

(after application of the rated Capacitance change Within ±25% of the initial value
C)
ØD+0.5 max.
＋
ØD 5 6.3 8
－ P±0.5 P 2.0 2.5 3.5
Ød 0.5 0.5 0.6
L+βmax. 15 min. 4 min. β 1.5

WV 10 16 25 35 50
Item Ripple Ripple Ripple Ripple Ripple

ØD×L current ØD×L current ØD×L current ØD×L current ØD×L current
(mA rms) (mA rms) (mA rms) (mA rms) (mA rms)
(mm) 105°C (mm) 105°C (mm) 105°C (mm) 105°C (mm) 105°C
μF 100kHz 100kHz 100kHz 100kHz 100kHz
1 5×11 32
2.2 5×11 42
3.3 5×11 84
4.7 5×11 96
10 5×11 108
22 5×11 132
33 5×11 156 5×11 175 6.3×11 228
47 5×11 175 5×11 175 6.3×11 252 6.3×11 228
100 5×11 175 6.3×11 252 6.3×11.5 252 8×11.5 396 8×11.5 324
220 6.3×11 252 8×11.5 396 8×11.5 396 8×15 430
330 8×11.5 396 8×11.5 396

μF
~ 33 0.42 0.70 0.90 0.95 1.00
47 ~ 0.55 0.73 0.92 0.96 1.00
134
LQ Low Imp., High Ripple Current

・For LED Lighting

C
C
WV 6.3 10 16 25 35 50 63 80 100
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08 0.08

C / Z+20°
C 2
C / Z+20°
C 3
C.
Rated voltage (Vdc) 6.3 ~ 10 16 ~ 100
Capacitance change Within ±30% of initial value Within ±25% of initial value
Load life Life time (hrs)

ØD
6.3Vdc 10~50Vdc 63~100Vdc
Ø5 ~ Ø6.3 6000 7000 6000
Ø8×11.5L 8000 9000 8000
Ø8×15L ~ 20L 9000 10000 9000
Ø10×12.5L 9000
Ø10×16L ~ 25L
10000
Ø12.5 ~
MINIATURE TYPES
ØD 5 6.3 8 10 12.5 16 18
ØD+0.5 max.
－ P±0.5
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
β 1.5 2.0

μF
~ 33 0.42 0.70 0.90 0.95 1.00
47 ~ 270 0.50 0.73 0.92 0.96 1.00
330 ~ 680 0.55 0.77 0.94 0.97 1.00
820 ~ 1800 0.60 0.80 0.96 0.98 1.00
2200 ~ 0.70 0.85 0.98 0.99 1.00
135
LQ series
WV 6.3 10 16 25 35
Item IMP. Ripple IMP. Ripple IMP. Ripple IMP. Ripple IMP. Ripple
(Ω)max. current (Ω)max. current (Ω)max. current (Ω)max. current (Ω)max. current
ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms)
20°
C 105°C 20°
C 105°C 20°
C 105°C 20°
C 105°C 20°
C 105°C
(mm) (mm) (mm) (mm) (mm)
100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
μF
47 5 ×11 0.400 450
68 5 ×11 0.400 450
100 5 ×11 0.400 450 6.3 ×11 0.170 700
120 5 ×11 0.400 450
150 5 ×11 0.400 450 6.3 ×11 0.170 700
180 8 ×11.5 0.075 1200
220 5 ×11 0.400 345 8 ×15 0.059 1600
270 10 ×12.5 0.053 1700
330 5 ×11 0.170 700 8 ×11.5 0.075 1200 8 ×20 0.041 1960
390 8 ×15 0.059 1600 10 ×16 0.038 2000
470 6.3 ×11 0.170 540 8 ×11.5 0.075 1200 10 ×12.5 0.053 1700 10 ×16 0.038 2100
560 8 ×11.5 0.110 1200 8 ×15 0.059 1600 8 ×20 0.041 1960 10 ×20 0.028 2500
680 8 ×15 0.059 1600 10 ×12.5 0.053 1700 10 ×16 0.036 2000 10 ×25 0.024 2900
820 8 ×11.5 0.075 945 10 ×12.5 0.053 1700 8 ×20 0.041 1960 12.5 ×20 0.025 2600
1000 8 ×15 0.059 1250 10 ×16 0.041 1960 10 ×16 0.036 2000 10 ×20 0.027 2500 12.5 ×20 0.025 2800
1200 10 ×12.5 0.053 1500 10 ×16 0.036 2000 10 ×25 0.023 2900 12.5 ×25 0.019 3200
12.5 ×30 0.018 3660
1500 8×20 0.041 1500 10×20 0.027 2500 12.5×20 0.024 2600
16 ×20 0.021 3330
12.5 ×34.5 0.016 4120
1800 10×16 0.036 1760 10×20 0.027 2500 10×25 0.023 2900 12.5×25 0.018 3200
16 ×25 0.017 3810
12.5 ×30 0.017 3660
2200 10×25 0.023 2900 12.5×20 0.024 2600
16 ×20 0.020 3330
2700 10 ×20 0.027 1960 10 ×20 0.024 2600 12.5 ×25 0.018 3200 12.5 ×34.5 0.015 4120
12.5 ×30 0.017 3660
3300 10×25 0.023 2250 12.5×25 0.018 3200 16×25 0.016 3810
16 ×20 0.020 3300
3900 12.5 ×20 0.024 2480 12.5 ×34.5 0.015 4120
12.5 ×30 0.018 3660
4700 12.5×25 0.018 2900 16×25 0.016 3810
16 ×25 0.016 3300
16 ×25 0.021 4120
5600 12.5×30 0.017 3450
16 ×25 0.017 3810
12.5 ×34.5 0.015 3570
6800
16 ×20 0.020 3250
8200 16 ×25 0.016 3630
WV 50 63 80 100
Item IMP. Ripple IMP. Ripple IMP. Ripple IMP. Ripple

20°
C 105°C 20°
C 105°C 20°
C 105°C 20°
C 105°C
(mm) (mm) (mm) (mm)
100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
μF
8.2 5 ×11 1.200 220
12 5 ×11 1.200 220
18 5 ×11 0.710 240 6.3 ×11 0.460 370
27 5 ×11 0.480 310 6.3 ×11 0.460 370
33 8 ×11.5 0.450 620
8 ×15 0.350 780
47 6.3×11 0.380 400 6.3×11 0.280 420 8×11.5 0.290 620
10 ×12.5 0.250 780
56 6.3 ×11 0.220 500 8 ×15 0.200 780 10 ×12.5 0.250 780
8 ×20 0.250 1040
68 10×12.5 0.170 780
10 ×16 0.105 1040
82 8 ×11.5 0.180 720 8 ×20 0.160 1040 10 ×16 0.105 1140
10 ×20 0.080 1430
100 8×11.5 0.120 950 8×15 0.130 990 10×16 0.110 1040
12.5 ×16 0.105 1430
120 8 ×15 0.082 1230 10 ×12.5 0.110 990 10 ×25 0.066 1620
10 ×20 0.084 1430
150 10×12.5 0.073 1280 8×20 0.096 1200 12.5×20 0.650 1750
12.5 ×16 0.110 1430
180 8 ×20 0.058 1580 10 ×16 0.076 1200 10 ×25 0.069 1620
220 10 ×16 0.050 1650 12.5 ×20 0.062 1750 12.5 ×25 0.045 2210
12.5 ×30 0.040 2400
270 10×20 0.070 1570 12.5×25 0.047 2210
16 ×20 0.046 1950
12.5 ×30 0.042 2400
330 10×20 0.036 2060 10×25 0.060 1990 12.5×34.5 0.034 2600
16 ×20 0.048 1950
12.5 ×40 0.030 2860
390 10 ×25 0.030 2240 12.5 ×20 0.041 1990 12.5 ×34.5 0.036 2600 16 ×25 0.036 2430
18 ×20 0.045 2270
12.5 ×40 0.032 2860 16 ×31.5 0.030 2640
470 12.5 ×20 0.030 2300 12.5 ×25 0.031 2460 16 ×25 0.038 2430
18×25 0.034 2500
18 ×20 0.045 2270
12.5 ×30 0.028 2760 16 ×35.5 0.028 2860
560 16×31.5 0.032 2640
16 ×20 0.032 2380 18 ×31.5 0.029 2860
16 ×35.5 0.029 2860 16 ×40 0.026 3510
680 12.5×25 0.024 2800 12.5×34.5 0.024 3040
18 ×25 0.036 2500 18 ×35.5 0.026 3510
12.5 ×30 0.022 3370 16 ×40 0.027 3510
820 16×25 0.025 2890 18×40 0.025 3860
16 ×20 0.025 3070 18 ×31.5 0.030 2860
12.5 ×34.5 0.020 3810
1000 16×31.5 0.023 2950 18×35.5 0.027 3510
16 ×25 0.021 3510
1200 18 ×40 0.026 3860
2200 18×40 0.02 3200
136

Upgrade
LJ 130°C, Long Life, Low Impedance

WV≦100V
・For LED Lighting, LED Display

C
C(10 ~ 100WV), -25 ~ +130°
C(200, 400WV)
WV ≦ 100 WV > 100
A whichever is greater (after 2 min.)
I = 0.02CV + 15μA (after 5 min.)
I = 0.03CV or 4μ
A whichever is greater (after 1 min.)
C
WV 10 16 25 35 50 63 100 200 400
(at 120Hz, 20°C)
tanδ 0.19 0.16 0.14 0.12 0.1 0.09 0.08 0.15 0.2
WV 10 16 25 35 50 63 100 200 400

Z-25°
C/Z+20°
C 3 2 2 2 2 2 2 3 6
Z-40°
C/Z+20°
C 6 4 3 3 3 3 3 - -
Rated voltage (Vdc) 10 ~ 100WV 200, 400WV

Capacitance change Within ±30% of initial value Within ±20% of initial value
tanδ Within ±300% of initial value Within ±200% of initial value
Life time(hrs)
voltage for 4000 hours at 130° C) ØD
~100V 200, 400V
ØD = 6.3 1,000 -
ØD = 8,10 2,000 3,000
ØD ≥ 12.5 4,000 -
C)
MINIATURE TYPES
ØD 8 10 12.5 16 18
ØD+0.5 max.
－ P±0.5
P 3.5 5.0 5.0 7.5 7.5
Ød 0.6 0.6 0.6 0.8 0.8
β 1.5 2.0

Frequency
WV μF 120Hz 1kHz 10kHz 50kHz 100kHz≦
~ 4.7 0.42 0.60 0.80 0.90 1.00
10 ~ 33 0.55 0.75 0.90 0.95 1.00
10~100 47 ~ 330 0.70 0.85 0.95 0.98 1.00
470 ~ 1500 0.75 0.90 0.98 1.00 1.00
2200 ~ 0.80 0.95 1.00 1.00 1.00
~ 5.6 0.20 0.40 0.80 0.90 1.00
200, 400 6.8 ~ 15 0.30 0.60 0.90 0.95 1.00
22 ~ 0.50 0.80 0.90 0.95 1.00
137
LJ series

WV 10 16 25 35 50
Item IMP. Ripple IMP. Ripple IMP. Ripple IMP. Ripple IMP. Ripple
(Ω)max. current (Ω)max. current (Ω)max. current (Ω)max. current (Ω)max. current
ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms)
20°
C 130°C 20°
C 130°C 20°
C 130°C 20°
C 130°C 20°
C 130°C
(mm) (mm) (mm) (mm) (mm)
100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
μF
4.7 8 ×11.5 1.00 100
10 8 ×11.5 0.80 200
22 8 ×11.5 0.80 260
33 8 ×11.5 0.60 300
47 8 ×11.5 0.60 300
100 8 ×11.5 0.220 360 10 ×12.5 0.180 520
220 8 ×11.5 0.220 360 10 ×12.5 0.150 620 10 ×20 0.082 890
330 8 ×11.5 0.22 360 8 ×11.5 0.22 360 10 ×12.5 0.150 620 10 ×16 0.10 800 12.5 ×20 0.065 1000
470 10 ×12.5 0.15 620 10 ×12.5 0.15 620 10 ×16 0.100 800 10 ×20 0.073 960 12.5 ×25 0.051 1200
1000 10 ×20 0.07 960 10 ×20 0.07 960 12.5 ×20 0.06 1100 12.5 ×25 0.040 1430 16 ×31.5 0.037 2180
2200 12.5 ×25 0.040 1430 12.5 ×25 0.040 1430 16 ×31.5 0.034 2300 16 ×35.5 0.031 2550 18 ×40 0.029 2800
3300 16 ×25 0.038 1900 16 ×31.5 0.034 2300 16 ×35.5 0.031 2550 18 ×35.5 0.028 2800
4700 16 ×31.5 0.034 2300 16 ×35.5 0.031 2550
WV 63 100 200 400
Item IMP. Ripple IMP. Ripple Ripple Ripple

(Ω)max. current (Ω)max. current current current
ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms) ØD×L (mA rms)
20°
C 130°C 20°
C 130°C 130°C 130°C
(mm) (mm) (mm) (mm)
100kHz 100kHz 100kHz 100kHz 100kHz 100kHz
μF
1.0 8 × 11.5 65
8 × 11.5 75
1.5
8 × 15 80
8 × 11.5 75
1.8
8 × 15 85
8 × 11.5 75
2.2 8 × 15 90
8 × 20 110
8 × 15 95
2.7
8 × 20 115
3.3 8 × 20 120
8 × 20 120
4.7 8×11.5 1.300 100 8 × 11.5 120
10 × 16 125
8 × 11.5 130 10 × 16 130
5.6
8 × 15 180 10 × 20 145
8 × 11.5 130 10 × 20 150
6.8
8 × 15 180
8 × 15 200
10 8×11.5 1.000 200
8 × 20 240
8 × 15 200
15
8 × 20 240
8 × 20 240
22 8×11.5 0.670 220
10 × 16 240
33 8 × 11.5 0.50 250 10 ×12.5 0.45 260 10 × 20 320
47 10 × 12.5 0.37 400 10 ×16 0.33 330
100 10 × 16 0.30 450 12.5 ×20 0.17 670
220 12.5 × 20 0.12 820 16 ×25 0.130 1100
330 12.5 × 25 0.102 1000 16 ×31.5 0.100 1300
470 16 × 25 0.089 1500 18 ×31.5 0.092 1600
1000 16 × 31.5 0.076 1850
1500 18 × 40 0.063 2350
138
BA For PSU, Smaller Case Size

Series
・105°
C 2000 hours
・Smaller case size for energy saving lamp & ballast
I = 0.03CV + 15μA (CV≦1000)
I = 0.02CV + 25μA (after 5 minutes)
Dissipation factor max. WV 160 200 250 350 400 450
(at 120Hz, 20°C) tanδ 0.10 0.10 0.10 0.15 0.15 0.15
WV 160 200 250 350 400 450

Z-25°
C/Z+20°
C 3 3 3 4 6 6
Z-40°
C/Z+20°
C 4 4 4 - - -
C.
Load life Less than specified value
Leakage current

ØD+0.5 max.
＋
ØD 8 10 12.5 16 18
－ P±0.5 P 3.5 5.0 5.0 7.5 7.5
Ød 0.6 0.6 0.6 0.8 0.8
L+βmax. 15 min. 4 min. β 1.5 2.0
MINIATURE TYPES
Safety vent

WV 160 200 250 350 400 450
μF
1.0 8 × 11.5 27 10 × 12.5 27
2.2 10 × 12.5 37 10 × 12.5 43 10 × 12.5 33
3.3 10 × 12.5 44 10 × 12.5 53 10 × 16 58 10 × 16 51
4.7 8 × 11.5 53 10 × 12.5 53 10 × 16 64 10 × 16 66 10 × 20 66
10 10 × 12.5 77 10 × 12.5 86 10 × 16 88 10 × 20 110 10 × 20 125 12.5 × 20 101
22 10 × 16 140 10 × 16 140 10 × 20 168 12.5 × 20 175 12.5 × 25 196 16 × 25 168
33 10 × 20 206 10 × 20 206 12.5 × 20 223 16 × 20 240 16 × 25 260 18 × 25 228
47 10 × 20 266 12.5 × 20 266 12.5 × 25 297 16 × 25 311 18 × 25 317
100 12.5 × 25 420 16 × 25 460 18 × 25 470 Ripple current (mA rms) at 105°
C, 120Hz
220 18 × 25 500 Case size ØD×L (mm)

μF Frequency 60Hz 120Hz 1kHz 10kHz 50kHz 100kHz≦
~ 47 0.75 1.00 1.55 2.00 2.00 2.00
100 ~ 0.80 1.00 1.34 2.00 2.00 2.00
139

Upgrade
RH For PSU High Ripple Current, Long Life

Series Long Life
・High ripple current

C
・Suited for ballast application
WV 160 ~ 450 500
Temperature range -40 ~ +105° C -25 ~ +105°
C
Leakage current max. I = 0.02CV + 15μA (after 5 minutes)
Dissipation factor max. WV 160 200 250 350 400 450 500
(at 120Hz, 20°C) tanδ 0.15 0.15 0.15 0.20 0.24 0.24 0.24
WV 160 200 250 350 400 450 500

Z-25°
C/Z+20°
C 3 3 3 4 6 6 6
Z-40°
C/Z+20°
C 4 4 4 8 10 10 -
C.
C)
Unit : mm
● DRAWING
＋ ØD 10 12.5 16 18 20 22
ØD+αmax.
P±0.5
P 5.0 5.0 7.5 7.5 10.0 10.0
－
Ød 0.6 0.6 0.8 0.8 0.8 1.0
β 2.0 3.0
α 0.5 1.0
Safety vent

~ 4.7 0.25 0.30 0.60 0.80 0.90 1.00
6.8 ~ 15 0.30 0.40 0.70 0.90 0.95 1.00
22 ~ 0.40 0.50 0.80 0.90 0.95 1.00
140
RH series

μF WV 160 200 250 350
4.7 10 × 16 200
6.8 10 × 12.5 120 10 × 12.5 120 10 × 16 200
10 10 × 16 250 10 × 16 300 10 × 20 300 10 × 20 280
15 10 × 12.5 260
10 × 16 360 10 × 16 360
22 12.5 × 20 600 12.5 × 20 350
10 × 20 500 10 × 20 500
10 × 20 500
33 10 × 20 500 12.5 × 20 600 16 × 20 500
12.5 × 20 600
47 12.5 × 20 600 12.5 × 20 660 12.5 × 25 720 16 × 25 660
68 12.5 × 25 600 12.5 × 25 760 16 × 25 920 16 × 31.5 800
82 16 × 20 760 16 × 20 880 16 × 25 1120 18 × 31.5 920
100 16 × 25 1100 16 × 25 1120 16 × 31.5 1200 18 × 31.5 1020
120 16 × 25 1180 16 × 31.5 1200 18 × 25 1200 18 × 31.5 1150
18 × 25 1250
150 16 × 31.5 1300 16 × 31.5 1300 18 × 40 1250
18 × 31.5 1250
220 18 × 35.5 1600
μF WV 400 420 450 500

1.0 10 × 12.5 90
10 × 12.5 100 10 × 12.5 100
2.2 10 × 16 120
10 × 16 120 10 × 16 120
3.3 10 × 16 140 10 × 16 140 10 × 16 140
4.7 10 × 16 180 10 × 16 180 10 × 20 180
6.8 10 × 16 200 10 × 16 200 10 × 20 200
12.5 × 20 300
10 10 × 20 280 10 × 20 280 12.5 × 20 300
12.5 × 25 360
15 12.5 × 16 280 12.5 × 25 360
12.5 × 20 430
22 12.5 × 25 430 12.5 × 25 430 16 × 25 420
16 × 25 550
33 16 × 25 640 16 × 25 660 16 × 31.5 700 16 × 31.5 560
47 16 × 31.5 750 16 × 31.5 750 16 × 31.5 700 18 × 35.5 700
56 18 × 25 750 18 × 35.5 740
MINIATURE TYPES
18 × 25 900
68 16 × 31.5 880 16 × 31.5 900 18 × 35.5 900
18 × 31.5 1000
18 × 31.5 1035
82 16 × 35.5 1000 16 × 35.5 1000 18 × 40 1030
18 × 35.5 1100
18 × 45 1100
100 18 × 35.5 1120 18 × 35.5 1170 18 × 35.5 1500
20 × 41 1200
120 18 × 40 1250 18 × 40 1280 18 × 40 1500
150 20 × 41 1380 20 × 41 1500 20 × 41 1796
180 20 × 41 1450 20 × 41 1600 22 × 45 1800

C, 100kHz
141

Upgrade
RU For PSU, High Ripple Current

Series
・High ripple current compared with RH series

C
WV 160 ~ 450 500
Temperature range -40 ~ +105°C -25 ~ +105°
C
Dissipation factor max. WV 160 200 250 350 400 450 500
(at 120Hz, 20°C) tanδ 0.15 0.15 0.15 0.20 0.20 0.20 0.24
WV 160 200 250 350 400 450 500

Z-25°
C/Z+20°
C 3 3 3 4 6 6 6
Z-40°
C/Z+20°
C 4 4 4 8 10 10 -
C.
C)
Unit : mm
ØD 10 12.5 16 18 20 22
ØD+αmax.
＋
P 5.0 5.0 7.5 7.5 10.0 10.0
－
P±0.5 Ød 0.6 0.6 0.8 0.8 0.8 1.0
β 2.0 3.0
L+βmax. 15 min. 4 min. α 0.5 1.0
Safety vent

μF Frequency 120Hz 1kHz 10kHz 50kHz 100kHz≦
~ 8.2 0.30 0.56 0.78 0.90 1.00
10 ~ 47 0.35 0.60 0.80 0.90 1.00
68 ~ 0.40 0.65 0.85 0.95 1.00
142
RU series

μF WV 160 200 250 350
6.8 10 × 12.5 250
10 10 × 16 290 10 × 16 350 10 × 16 350 10 × 20 325
15 10 × 16 340 10 × 16 430 10 × 16 430 10 × 20 360
22 10 × 16 415 10 × 20 525 12.5 × 20 525 12.5 × 20 405
33 10 × 20 580 695 12.5 × 20 695 16 × 20 580
47 12.5 × 20 635 10 × 12.5 765 12.5 × 25 835 16 × 25 765
16 × 20 1000
68 12.5 × 25 695 12.5 × 20 880 18 × 25 925
16 × 25 1065
16 × 25 1275
82 12.5 × 25 880 12.5 × 25 1100 18 × 25 985
18 × 25 1300
100 16 × 20 1200 16 × 25 1275 18 × 25 1330 18 × 31.5 1180
120 16 × 25 1330 18 × 25 1390 18 × 25 1450 18 × 31.5 1330
18 × 25
150 16 × 25 1450 18 × 25 1500 1550 18 × 40 1450
18 × 25
μF WV 400 420 450 500

3.3 10 × 12.5 180
10 × 16 310 10 × 16 310
10 12.5 × 20 345 12.5 × 20 345
10 × 20 325 10 × 20 325
15 10 × 20 400 10 × 20 450 16 × 20 530 16 × 25 490
12.5 × 20 475 12.5 × 20 490 16 × 20
22 635 16 × 25 485
12.5 × 25 500 12.5 × 25 520 16 × 25
16 × 25
33 16 × 25 740 16 × 25 750 810 16 × 31.5 650
18 × 20
18 × 25 18 × 25 18 × 25
47 870 890 900 18 × 35.5 810
16 × 31.5 16 × 31.5 16 × 31.5
68 18 × 31.5 1020 18 × 31.5 1100 18 × 31.5 1160 18 × 35.5 1040
82 18 × 31.5 1160 18 × 31.5 1200 18 × 31.5 1250 18 × 40 1100
100 18 × 35.5 1300 18 × 35.5 1400 18 × 35.5 1450 20 × 41 1275
120 18 × 40 1450 18 × 40 1600 18 × 40 1620 22 × 45 1800
18 × 45 1500 18 × 45 1650 18 × 45 1700
150
20 × 41 1600 20 × 41 1750 20 × 41 1800
MINIATURE TYPES
C, 100kHz
143
BH For PSU, High Ripple Current

Series Long Life
・Higher ripple current compared with RH series

・Operating tempersture range of -25 ~ +105° C
C
C
I = 0.04CV + 100μA (after 1 minute)
C
Dissipation factor max. WV 200 250 350 400

(at 120Hz, 20°C) tanδ 0.15 0.15 0.20 0.24
Low temperature characteristics WV 200 250 350 400

C/Z+20°
C 3 3 6 6
C.

C) After 1000 hours no load test, leakage current, capacitance and tanδare same as load life value.
Unit : mm

μF WV 200 250 350 400
2.2 10 × 16 160
3.3 10 × 16 190 10 × 16 180
4.7 10 × 16 220 10 × 16 220
6.8 10 × 16 280 10 × 16 280
8 × 20 300 8 × 20 400
8.2 × 300 10 × 20 400
10 16
8 × 20 300 8 × 23 400
10 10 × 16 320 10 × 16 320
10 × 20 400 10 × 20 400
8 × 20 300 8 × 23 350 10 × 30 500 12.5 × 20 700
12.5 × 20 650
22 10 × 20 550 10 × 20 550 12.5 × 25 780
12.5 × 25 680
33 12.5 × 20 700 12.5 × 20 800 16 × 25 910 16 × 25 920
12.5 × 30 1050
47 12.5 × 20 980 12.5 × 25 1040
18 × 20 1150
12.5 × 20 1100 12.5 × 30 1300
68 16 × 31.5 1300
12.5 × 25 1300 16 × 25 1350
82 16 × 20 1450 12.5 × 30 1450
C, 100kHz
12.5 × 30 1550
100 Case size ØD×L (mm)
16 × 25 1630

~ 4.7 0.30 0.40 0.60 0.80 0.90 1.00
6.8 ~ 10 0.35 0.40 0.70 0.90 0.95 1.00
22 ~ 0.40 0.50 0.80 0.90 0.95 1.00
144
PQ For PSU, High Ripple Current, Long Life

Series

C
C
Dissipation factor max. Rated Voltage(V) 400 450
(at 120Hz, 20°C) tanδ 0.20 0.20
Low temperature characteristics WV 400 450

C) / Z(+20°
C) 6 6
C.
ØD 12.5 16 18 20
＋
ØD+αmax.
P 5.0 7.5 7.5 10.0

－ P±0.5
Ød 0.6 0.8 0.8 0.8
β 2.0 3.0
L+βmax. 15 min. 4 min. α 0.5 1.0
MINIATURE TYPES
Safety vent

WV 400 450
μF
22 12.5 × 25 215 16 × 25 175
33 16 × 25 320 16 × 31.5 350
47 16 × 31.5 375 16 × 31.5 350
68 16 × 31.5 435 18 × 25 520
82 18 × 31.5 500 18 × 31.5 600
100 18 × 35.5 560 18 × 35.5 750
120 18 × 40 625 18 × 40 850
150 20 × 41 690 20 × 41 930

C, 120Hz

~ 68 0.80 1.00 1.60 1.80 1.90 2.00
82 ~ 0.50 1.00 1.08 1.33 1.50 1.67
145

NEW
MU For Display, 5000 hours at 150°

Series
C
・High ripple current compared with RU series

C
WV 160 ~ 350 400 ~ 500
Temperature range -40 ~ +105° C -25 ~ +105° C
I = 0.04CV + 100μA (after 1 minutes),
Dissipation factor max. WV 160 200 250 350 400 420 450 500
(at 120Hz, 20°C) tanδ 0.20 0.24
WV 160 200 250 350 400 420 450 500

Z-25°
C/Z+20°
C 3 3 3 3 6 6 6 6
Z-40°
C/Z+20°
C 4 4 4 6 - - - -
C.
Unit : mm
● DRAWING
＋ ØD 10 12.5 16 18 20
ØD+αmax.
P 5.0 5.0 7.5 7.5 10.0

－ P±0.5
Ød 0.6 0.6 0.8 0.8 0.8
β 2.0 3.0
Safety vent

Frequency 120Hz 300Hz 1kHz 10kHz 100kHz≦
μF
10 ~ 82 1.00 1.75 2.25 2.35 2.50
100 ~ 470 1.00 1.67 2.05 2.15 2.25
146
MU series

μF WV 160 200 250 350
10 10 × 16 102 10 × 16 110 10 × 12.5 110 10 × 16 135
22 10 × 16 195 10 × 16 200 10 × 16 195 12.5 × 20 270
27 10 × 16 222 10 × 16 222 10 × 20 240 12.5 × 20 285
33 10 × 16 245 10 × 20 280 12.5 × 20 294 12.5 × 20 290
39 10 × 16 265 10 × 20 305 12.5 × 20 322 12.5 × 25 320
10 × 20 335
47 10 × 20 335 12.5 × 20 400 16 × 25 410
12.5 × 20 400
12.5 × 20 447 12.5 × 25 540
68 12.5 × 20 400 16 × 25 550
12.5 × 25 540 16 × 20 540
10 × 25 450 12.5 × 25 560
82 16 × 20 600 18 × 25 625
12.5 × 20 450 16 × 20 560
12.5 × 25 525 16 × 25 652
100 16 × 25 652 18 × 31.5 743
16 × 20 525 18 × 20 652
12.5 × 25 580
120 16 × 25 714 16 × 25 714 18 × 35.5 840
16 × 25 580
150 16 × 25 750 16 × 25 760 18 × 25 820 18 × 35.5 942
180 16 × 25 810 16 × 31.5 850 18 × 31.5 920 18 × 40 1050
16 × 31.5 880
220 18 × 31.5 1000 18 × 31.5 1000
18 × 25 880
270 16 × 35.5 1000 18 × 35 1150
16 × 40 1142
330 18 × 40 1250
18 × 31.5 1119
470 18 × 40 1401
μF WV 400 420 450 500

10 10 × 16 135 10 × 20 135 10 × 20 135 12.5 × 20 165
22 12.5 × 20 270 12.5 × 20 225 12.5 × 25 296 16 × 20 260
27 12.5 × 20 285 12.5 × 20 254 12.5 × 25 305 16 × 25 329
33 12.5 × 25 320 16 × 20 345 16 × 20 364 16 × 25 350
39 12.5 × 25 320 16 × 25 345 16 × 25 400 16 × 31.5 413
16 × 25 420 16 × 25 450 16 × 25 450 16 × 35.5 462
47
18 × 20 436 18 × 20 450 18 × 20 450 18 × 31.5 468
18 × 25
MINIATURE TYPES
16 × 31.5 540 520 18 × 25 560 16 × 45 630
68
18 × 25 540 18 × 31.5 580 18 × 31.5 590 18 × 35.5 600
18 × 25 600 16 × 40 650 16 × 50 685
82 18 × 31.5 700
18 × 31.5 650 18 × 31.5 670 18 × 40 670
18 × 31.5 743 16 × 45 770 16 × 45 770 18 × 45 800
100
18 × 35.5 820 18 × 35.5 770 18 × 35.5 790 20 × 41 800
18 × 35.5 840 16 × 50 850 16 × 50 850
120 18 × 50 920
18 × 40 912 18 × 40 850 18 × 40 850
18 × 45 1000
150 18 × 40 1020
20 × 41 1000
18 × 45 1080 Ripple current (mA rms) at 105°
C, 120Hz
180
20 × 41 1080 Case size ØD×L (mm)
147

Upgrade
BL For PSU, High Ripple Current, Long Life

Series Long Life
・High ripple current

・Operating temperature range of -25 ~ +105°
C
・For power supply and adapter
C
C
(at 120Hz, 20°C) tanδ 0.15 0.15 0.15 0.20 0.20 0.20 0.20 0.24
Low temperature characteristics WV 160 200 250 350 400 420 450 500
C/Z+20°
C 3 3 3 4 6 6 6 6
C.
Ø8 products are for 9000 hours
ØD 8 10 12.5 16 18 20
ØD+αmax.
＋
P 3.5 5.0 5.0 7.5 7.5 10.0
－
P±0.5 Ød 0.6 0.6 0.6 0.8 0.8 0.8
β 1.5 2.0 3.0
L+βmax. 15 min. 4 min. α 0.5 1.0
Safety vent

Frequency 60Hz 120Hz 1kHz 10kHz 50kHz 100kHz≦
Coefficient 0.35 0.50 0.80 0.90 0.95 1.00
148
BL series

μF WV 160 200 250 350
4.7 8 × 11.5 160
8 × 11.5 180
6.8 10 × 16 220
10 × 12.5 190
8 × 15 240 8 × 20 350
10 10 × 16 250 10 × 16 250
10 × 20 280 10 × 20 280
22 10 × 20 500 10 × 20 500 12.5 × 20 600 12.5 × 20 350
33 10 × 20 500 12.5 × 20 600 12.5 × 20 600 16 × 20 500
47 12.5 × 20 660 12.5 × 20 660 12.5 × 25 720 16 × 25 660
12.5 × 25 760
68 12.5 × 25 760 16 × 25 920 18 × 25 840
10 × 30 950
12.5 × 30 955 18 × 31.5 900
82 12.5 × 25 830 16 × 25 955
16 × 25 1010
100 16 × 25 1120 18 × 25 1120 18 × 25 1200
150 18 × 25 1360 18 × 25 1360
μF WV 400 420 450 500

1 8 × 11.5 60 8 × 11.5 82
2.2 8 × 11.5 80 8 × 11.5 94
3.3 8 × 11.5 130 8 × 11.5 130
3.9 8 × 11.5 140 8 × 15 150
8 × 15 145 8 × 20 220
4.7
10 × 12.5 190 10 × 16 220
8 × 20 350
6.8 10 × 16 220
10 × 16 220
10 10 × 20 280 10 × 20 300 12.5 × 20 320 12.5 × 25 320
15 10 × 20 320
430 12.5 × 20 400 16 × 25 560

12.5 × 25
22 12.5 × 25 430 12.5 × 25 400
16 × 20 430 16 × 31.5 675
16 × 25 560
33 16 × 25 640 16 × 25 680 18 × 25 700 18 × 35.5 720
47 18 × 25 840 18 × 31.5 840 18 × 31.5 880 18 × 40 1000
18 × 25 900 18 × 25 1000 18 × 35.5 1000
68 18 × 31.5 870
18 × 31.5 930 18 × 31.5 1000 18 × 40 1060
MINIATURE TYPES
82 18 × 35.5 950 18 × 31.5 1000 18 × 35.5 1050 16 × 50 1100
18 × 35.5 1050 18 × 35.5 1100
100 18 × 40 1000
18 × 40 1100 18 × 40 1150
120 18 × 40 1200
150 20 × 41 1300

C, 100kHz
149
BG For PSU, Long Life

Series Long Life

C
・For power supply and adapter
C
Dissipation factor max. Rated Voltage(V) 400 450
(at 120Hz, 20°C) tanδ 0.20 0.20
Low temperature characteristics WV 400 450

C) / Z(+20°
C) 6 6
C.
ØD 12.5 16 18 20
ØD+αmax.
＋
P 5.0 7.5 7.5 10.0
－ P±0.5
Ød 0.6 0.8 0.8 0.8
β 2.0 3.0
α 0.5 1.0
Safety vent

WV 400 450
μF
22 12.5 × 25 430 12.5 × 25 350
33 16 × 20 640 16 × 25 650
47 18 × 20 840 18 × 20 880
68 18 × 25 870 18 × 25 1000
82 18 × 31.5 950 18 × 31.5 1050
100 18 × 31.5 1000 18 × 35.5 1100
120 18 × 40 1160 18 × 40 1300
150 20 × 41 1280 20 × 41 1440

C, 100kHz

Coefficient 0.50 0.80 0.90 0.95 1.00
150

Upgrade
BJ For PSU, High Ripple, Long Life

Series Long Life

C
Operating temperature range -40 ~ +105°C (160 ~ 250WV), -25 ~ +105° C (350 ~ 500WV)
Leakage current max. I = 0.04CV + 100μA (after 1 minutes), I = 0.02CV + 25μA (after 5 minutes)
C
(at 120Hz, 20°C) tanδ 0.15 0.15 0.15 0.20 0.20 0.20 0.20 0.24
WV 160 200 250 350 400 420 450 500

C/Z+20°
C 3 3 3 6 6 6 6 6
Z-40°
C/Z+20°
C 4 4 4 - - - - -
C.
Load life
500WV products are for 10000 hours
C)
＋ ØD 10 12.5 16 18 20
ØD+αmax.
MINIATURE TYPES
－ P±0.5 P 5.0 5.0 7.5 7.5 10.0
Ød 0.6 0.6 0.8 0.8 0.8
β 2.0 3.0
α 0.5 1.0
Safety vent

Frequency
WV μF 120Hz 1kHz 10kHz 50kHz 100kHz≦
~ 15 0.30 0.60 0.90 0.95 1.00
160~450 22 ~ 47 0.40 0.70 0.90 0.95 1.00
68 ~ 0.50 0.80 0.90 0.95 1.00
~ 39 0.40 0.70 0.90 0.95 1.00
500
47 ~ 0.50 0.80 0.90 0.95 1.00
151
BJ series

μF WV 160 200 250 350
4.7 10 × 12.5 180
6.8 10 × 12.5 290 10 × 16 280
10 10 × 16 325 10 × 16 370 10 × 16 370 10 × 20 420
22 10 × 16 520 10 × 20 580 10 × 20 580 12.5 × 20 675
27 10 × 16 555 10 × 20 625 10 × 20 600 12.5 × 20 713
33 10 × 16 690 10 × 20 750 12.5 × 20 775 16 × 20 780
39 10 × 20 690 12.5 × 20 763 12.5 × 20 805 16 × 20 800
47 10 × 20 840 12.5 × 20 1000 12.5 × 20 1000 16 × 25 1125
12.5 × 25 1080
68 12.5 × 20 875 16 × 20 1100 18 × 25 1220
16 × 20 1100
82 12.5 × 25 945 16 × 25 1120 16 × 20 1340 18 × 25 1370
12.5 × 25 16 × 25
100 1210 16 × 25 1304 1400 18 × 31.5 1470
16 × 20 18 × 20
120 16 × 25 1325 16 × 25 1428 18 × 25 1495 18 × 35.5 1680
150 16 × 25 1495 18 × 25 1570 18 × 25 1740 18 × 40 1884
180 16 × 25 1620 18 × 25 1600 18 × 31.5 1840 20 × 41 2100
220 18 × 25 1900 18 × 31.5 2020 18 × 35.5 2000
270 16 × 35.5 2000 18 × 35.5 2300
330 16 × 40 2280 18 × 40 2500
470 18 × 45 2804
μF WV 400 420 450 500

4.7 10 × 16 220 10 × 16 220
10 × 16 330
6.8 10 × 16 280
10 × 20 400
10 × 20 400
10 10 × 20 420 10 × 20 420 12.5 × 20 413
12.5 × 20 480
12.5 × 20 480
15 12.5 × 20 480 12.5 × 20 480 12.5 × 25 440
12.5 × 25 600
12.5 × 25 745 12.5 × 25 890
22 12.5 × 25 720 16 × 25 675
16 × 20 780 16 × 20 900
27 16 × 20 730 16 × 20 875 16 × 20 950 16 × 25 823
12.5 × 30 980 16 × 25 16 × 31.5
33 16 × 20 960 1095 880
16 × 25 1035 18 × 20 18 × 25
39 16 × 20 1000 16 × 25 1050 16 × 25 1100 16 × 31.5 1033
16 × 25 12.5 × 40 1125
47 1080 18 × 25 1150 18 × 31.5 1033
18 × 20 16.5 × 25 1125
68 16 × 31.5 1190 18 × 25 1150 18 × 31.5 1180 18 × 40 1200
82 18 × 31.5 1490 18 × 31.5 1450 18 × 35.5 1430 18 × 40 1340
18 × 35.5 1740
100 18 × 35.5 1810 18 × 35.5 1700 20 × 41 1600
18 × 40 1740
120 18 × 40 1824 18 × 40 1700 18 × 45 1740
150 20 × 41 2040 20 × 41 2000

C, 100kHz
152
BK For PSU, High Temperature

Series
・High reliability withstanding 5000 Hours load life at 125°

C
・Suitable for compact energy saving lamp
Leakage current max. I = 0.03CV+15μA (CV≦1000), I = 0.02CV+25μA (CV >1000) (after 5 minutes)
C
Dissipation factor max. Rated Voltage(V) 160 200 250 350 400 450
(at 120Hz, 20°C) tanδ 0.15 0.15 0.15 0.20 0.24 0.24
Low temperature characteristics WV 160 200 250 350 ~ 450

C/Z+20°
C 3 3 3 6
C.
450WV products are for 2000 hours.
C)
ØD 10 12.5 16
ØD+0.5 max.
－ P±0.5
P 5.0 5.0 7.5
Ød 0.6 0.6 0.8
β 2.0
MINIATURE TYPES
Safety vent

WV 160 200 250 350 400 450
μF
2.2 10 × 12.5 90 10 × 12.5 90
3.3 10 × 12.5 90 10 × 16 120 10 × 16 100

10 × 12.5 100 10 × 16 130
4.7 10 × 12.5 90 10 × 12.5 100 10 × 20 170 10 × 25 104
10 × 16 120 10 × 20 170
10 × 12.5 110 10 × 12.5 130 10 × 16 140
10 12.5 × 20 250 12.5 × 20 250 12.5 × 20 155
10 × 16 140 10 × 16 160 10 × 20 170
22 10 × 20 280 10 × 20 280 12.5 × 20 300 16 × 25 277
C,
33 12.5 × 20 400 12.5 × 20 400 12.5 × 25 450 16 × 31.5 365
100kHz
47 12.5 × 25 520 12.5 × 25 520 Case size ØD×L (mm)

Coefficient 0.30 0.40 0.70 0.90 0.95 1.00
153
BM For PSU, 2000 hours at 150°

Series
C

C
・Suitable for compact energy saving lamp
A (after 5 minutes)
Dissipation factor max. Rated Voltage(V) 160 200 350 400
(at 120Hz, 20°C) tanδ 0.20 0.20 0.24 0.24

C/Z+20°
C 3 3 6 6
C.
Unit : mm
● DRAWING
ØD 10 12.5
ØD+0.5 max.
＋
P 5.0 5.0
－ P±0.5
Ød 0.6 0.6
β 2.0
Safety vent

μF WV 160 200 350 400
2.2 10 × 12.5 36 10 × 16 42
3.3 10 × 12.5 48 10 × 16 50
4.7 10 × 16 77 10 × 20 83
5.6 10 × 20 100 12.5 × 20 97
10 10 × 12.5 110 10 × 16 83 12.5 × 25 120 12.5 × 25 105
22 10 × 20 160 10 × 20 170
33 12.5 × 20 230 12.5 × 20 210 Case size ØD×L (mm)
47 12.5 × 25 250 12.5 × 25 240 Ripple current (mA rms) at 150°
C, 120Hz

Coefficient 0.75 1.00 1.50 1.75 1.77 1.80
154
PF High Ripple Current, High Reliability

Series Long Life
・High ripple current for diaplay module

C
Dissipation factor max. WV 160 200 250 275
(at 120Hz, 20°C) tanδ 0.15 0.15 0.15 0.20

C/Z+20°
C 4 4 4 4
C.
C)

ØD+0.5 max.
＋
ØD 10 12.5 16 18
－ P±0.5 P 5.0 5.0 7.5 7.5
Ød 0.6 0.6 0.8 0.8
L+βmax. 15 min. 4 min. β 2.0
MINIATURE TYPES
Safety vent

μF WV 160 200 250 275
10 10 × 16 320 10 × 16 320 10 × 16 320
22 10 × 16 500 10 × 16 500 10 × 20 500 10 × 20 350
33 10 × 20 650 10 × 20 650 12.5 × 20 770 12.5 × 20 500
47 10 × 20 750 12.5 × 20 840 12.5 × 20 980 12.5 × 25 840
68 12.5 × 20 970 12.5 × 25 970 16 × 20 1080 16 × 25 970
82 12.5 × 25 1060 16 × 20 1125 16 × 20 1190 18 × 25 1100
100 12.5 × 25 1250 16 × 20 1230 16 × 25 1425 18 × 25 1400
120 16 × 20 1350 16×20, 18×20 1435 18 × 25 1660 18 × 31.5 1600
16 × 25 1610 18 × 25 1740 18 × 25 2000 18 × 35.5 1900
150
18 × 31.5 2075

C, 100kHz

Frequency(Hz) 50(60)Hz 120Hz 1kHz 10kHz 50kHz 100kHz≦
Coefficient 0.30 0.40 0.70 0.80 0.90 1.00
155
CS For Charger and Adapter

Series
・Load life of 2000 hours at 105°

C
・Voltage range 400 ~ 450V
Dissipation factor max. 0.2max. at 120Hz, 20° C
Appearance Normal
Surge test Leakage current Less than specified value
(1.5kVDC: 5th interval 5 sec) Capacitance change Within initial value

Shelf life (at 85°
C/105°
C)

ØD+0.5 max.
－ P±0.5
15 min. 4 min.
Safety vent
ØD 8 10 12.5 16 18
P 3.5 5.0 5.0 7.5 7.5
Ød 0.6 0.6 0.8 0.8 0.8
β 1.5 2.0 2.0 2.0 2.0
Note : Other case sizes, rated voltage or capacitance are available upon request.
Please check with us about individual size and dimensions.
156
RB High Temperature, For 125°

Series
C Use
Solvent Proof
WV≦100V
・Load life of 2000 hours at 125°C

・For Electronic Control unit and other high
temperature applications
Operating temperature range WV≦50: -55 ~ +125°C, WV≧63: -40 ~ +125° C
WV≦50: I = 0.01CV or 3μA whichever is greater (after 2 minutes)
WV≧63: 0.03CV +10μA(after 5 min.)
C
Rated Votage(V) 6.3 10 16 25 35 50 63 ~ 100 160 ~ 250
(at 120Hz, 20°C)
tanδ 0.22 0.19 0.16 0.14 0.12 0.10 0.08 0.15
WV 6.3 ~10 16 ~ 250

Z-25°
C/Z+20°
C 3 2
Z-40°
C/Z+20°
C 5 4

Load life
Ø5, 6.3 and WV≧100 products are for 1000 hours
C)
Unit : mm
● DRAWING
MINIATURE TYPES
ØD+0.5 max.
＋
ØD 5 6.3 8 10 12.5 16 18
－ P±0.5
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
L+βmax. 15 min. 4 min. β 1.5 2.0

Frequency
WV μF 60Hz 120Hz 1kHz 10kHz 50kHz 100kHz≦
~ 47 0.38 0.50 0.78 1.00 1.00 1.00
6.3~100 68 ~ 680 0.46 0.57 0.77 0.86 0.93 1.00
1000 ~ 0.57 0.67 0.77 0.77 0.88 1.00
0.47 ~ 220 0.44 0.56 0.78 0.89 0.94 1.00
160~250
330 ~ 0.60 0.67 0.75 0.77 0.88 1.00
157
RB series

WV 6.3 10 16
Item Ripple Ripple Ripple

(mm) 125°C (mm) 125°C (mm) 125°C
μF 100kHz 100kHz 100kHz
33
47 5×11 124
68 5×11 124 6.3×11 176
100 5×11 120 6.3×11 168 6.3×11 212
150 6.3×11 180 6.3×11 212 8×11.5 310
220 6.3×11 228 8×11.5 310 8×11.5 368
330 8×11.5 234 8×11.5 368 10×12.5 500
470 10×12.5 460 10×12.5 480 10×16 616
680 10×16 560 10×16 616 10×20 816
1000 10×20 760 10×20 848 12.5×20 1129
1500 10×25 976 12.5×20 1134 12.5×25 1328
2200 12.5×20 1150 12.5×25 1368 16×20 1440
3300 12.5×25 1368 16×20 1480 16×25 1676
4700 16×25 1548 16×31.5 1936 16×35.5 2144
6800 16×31.5 1896 16×35.5 2144 18×35.5 2320
10000 16×40 2200 18×40 2432
15000 18×40 2368
WV 25 35 50
Item Ripple Ripple Ripple

(mm) 125°C (mm) 125°C (mm) 125°C
μF 100kHz 100kHz 100kHz
1.0 5×11 29
1.5 5×11 36
2.2 5×11 43
3.3 5×11 53
4.7 5×11 65
6.8 5×11 73
10 5×11 92
15 5×11 116
22 5×11 128 6.3×11 156
33 5×11 124 6.3×11 180 6.3×11 192
47 6.3×11 168 6.3×11 216 8×11.5 275
68 6.3×11 208 8×11.5 307 8×11.5 328
100 8×11.5 306 8×11.5 368 10×16 465
150 8×11.5 368 10×12.5 500 10×20 656
220 10×12.5 480 10×16 616 10×25 832
330 10×16 600 10×20 848 12.5×20 1025
470 10×20 816 12.5×20 1121 12.5×25 1200
680 12.5×20 1114 12.5×25 1328 16×20 1304
1000 12.5×25 1328 16×20 1416 16×31.5 1696
1500 16×20 1416 16×31.5 1908 16×40 1928
2200 16×25 1641 16×35.5 2144 18×40 2048
3300 16×35.5 2144 18×40 2432
4700 18×40 2368
158
RB series

WV 63 100 160
Item
Ripple current Ripple current Ripple current
ØD×L ØD×L ØD×L
(mm) (mm) (mm)
125°C 100kHz 125°C 100kHz 125°C 100kHz
μF
0.47 8×11.5 13 8×11.5 13 10×12.5 10
1.0 8×11.5 19 8×11.5 19 10×12.5 15
2.0 8×11.5 28 10×12.5 33 10×16 24
3.3 8×11.5 34 10×16 44 10×16 32
4.7 8×11.5 41 10×16 52 10×20 38
10 8×11.5 60 10×20 83 12.5×20 66
22 10×16 113 12.5×25 157 16×25 118
33 10×20 151 16×25 214 16×31.5 158
47 12.5×20 211 16×31.5 279
100 12.5×25 336
WV 200 250
Item
Ripple current Ripple current
ØD×L ØD×L
(mA rms) (mA rms)
(mm) (mm)
125°C 100kHz 125°C 100kHz
μF
0.47 10×12.5 10 10×12.5 10
1.0 10×12.5 15 10×12.5 14
2.0 10×16 24 10×16 24
3.3 10×20 32 10×20 32
4.7 10×20 38 12.5×20 45
10 12.5×20 72 16×25 79
22 16×31.5 129
MINIATURE TYPES
159
WT High Temperature, For 125°

Long Life Series
C Use
Low Impedance Solvent Proof
・Load life of 5000 hours at 125° C

・Low impedance at high frequency
・For electronic control unit and other high
Leakage Current max. I = 0.03CV or 3μ
Capacitance Tolerance ±20% at 120Hz, 20° C
Dissipation Factor max. WV 6.3 10 16 25 35 50 63 100
(at 120Hz, 20°
C)
tanδ 0.22 0.20 0.16 0.14 0.12 0.10 0.10 0.08
WV 6.3 10 16 25 35 50 63 100
Z-25°
C/Z+20°
C 3 3 3 2 2 2 2 2
Z-40°
C/Z+20°
C 6 6 4 3 3 3 3 3

Load life tanδ Less than 300% of the specified value
(after application of the rated Leakage current Less than specified value
voltage for 5000 hours at 125° C) ØD ØD = 6.3 ØD = 8 ØD = 10 ØD ≧ 12.5
Unit : mm
● DRAWING

ØD+0.5 max.
＋
ØD 5 6.3 8 10 12.5 16
－ P±0.5
P 2.0 2.5 3.5 5.0 5.0 7.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8
L+βmax. 15 min. 4 min. β 1.5 2.0

μF
~ 33 0.20 0.50 0.80 0.90 1.00
47 ~ 100 0.25 0.60 0.90 0.95 1.00
150 ~ 220 0.35 0.70 0.92 0.96 1.00
330 ~ 680 0.45 0.75 0.95 0.97 1.00
1000 ~ 1500 0.50 0.80 0.96 0.98 1.00
2200 ~ 0.55 0.85 0.98 0.99 1.00
160
WT series

WV 6.3 10 16 25

(mm) 20°
C 125°C (mm) 20°
C 125°C (mm) 20°
C 125°C (mm) 20°
C 125°C
47 5×11 0.80 250
68 5×11 0.80 250 5×11 0.80 250 6.3×11 0.34 405
100 5×11 0.80 250 6.3×11 0.34 405 6.3×11 0.34 405 6.3×11 0.34 405
150 6.3×11 0.34 405 6.3×11 0.34 405 6.3×11 0.34 405 8×11.5 0.28 760
220 6.3×11 0.34 405 8×11.5 0.30 760 8×11.5 0.28 760 10×12.5 0.14 1030
330 8×11.5 0.28 760 8×11.5 0.28 760 10×12.5 0.14 1030 10×16 0.10 1430
470 10×12.5 0.14 1030 10×12.5 0.14 1030 10×16 0.10 1430 10×20 0.08 1500
680 10×16 0.10 1430 10×16 0.10 1430 10×20 0.06 1500 12.5×20 0.06 1720
1000 10×20 0.06 1500 10×20 0.06 1500 12.5×20 0.06 1720 12.5×25 0.05 1900
1500 10×25 0.06 1620 12.5×20 0.06 1720 12.5×25 0.05 1900
2200 12.5×20 0.06 1720 12.5×25 0.05 1900
3300 12.5×25 0.05 1900
WV 35 50 63 100

(mm) 20°
C 125°C (mm) 20°
C 125°C (mm) 20°
C 125°C (mm) 20°
C 125°C
10
22 5 ×11 0.80 250 10× 12.5 0.80 480
33 6.3 ×11 0.34 405 8× 11.5 0.65 300 8× 11.5 1.50 150 10× 12.5 0.80 480
47 6.3 ×11 0.34 405 8× 11.5 0.50 440 10× 12.5 0.59 530 10× 16 0.55 630
68 8 ×11.5 0.19 760
100 8 ×11.5 0.28 760 10× 12.5 0.30 555 10× 16 0.41 690 12.5× 20 0.25 990
150 10 ×12.5 0.14 1030
MINIATURE TYPES
220 10 ×16 0.10 1430 10× 20 0.15 930 12.5× 20 0.16 1050 16× 25 0.11 1500
330 10 ×25 0.06 1620 12.5× 20 0.13 1330 12.5× 25 0.12 1290 16× 31.5 0.08 1790
470 12.5 ×20 0.06 1720 12.5× 25 0.10 1650 12.5× 34.5 0.10 1460
680 12.5 ×25 0.05 1900 16× 31.5 0.05 2430
161
VA 130°C, Long Life, Low Impedance

Series Low Impedance Long Life Solvent Proof

・Low impedance at high frequency
・For Electronic Control Unit and other high temperature applications
Operating temperature range -40 ~ +130° C
Dissipation factor max. Rated Voltage(V) 10 16 25 35
(at 120Hz, 20°C)
tanδ 0.20 0.16 0.14 0.12
WV 10 16 25 35
C/Z+20°
C 3 2 2 2
Z-40°
C/Z+20°
C 6 4 3 3

voltage for 4000 hours at 130° C) ØD ØD ≦ 10 ØD ≧ 12.5

ØD 8 10 12.5 16 18
ØD+0.5 max.
＋ P 3.5 5.0 5.0 7.5 7.5

－ P±0.5 Ød 0.6 0.6 0.6 0.8 0.8
β 1.5 2.0
Safety vent

μF
~ 330 0.50 0.85 0.95 0.97 1.00
470 ~ 1500 0.55 0.90 0.98 0.99 1.00
2200 ~ 0.60 0.95 1.00 1.00 1.00
162
VA series

WV 10 16
Item Impedance Ripple Impedance Ripple

ØD×L current ØD×L current
(Ω)max. (Ω)max.
(mA rms) (mA rms)
(mm) 20°
C 130°C (mm) 20°
C 130°C
μF 100kHz 100kHz 100kHz 100kHz
220
330 8×11.5 0.22 360 8×11.5 0.22 360
470 10×12.5 0.15 620 10×12.5 0.15 620
1000 10×20 0.073 960 10×20 0.073 960
2200 12.5×25 0.040 1430 12.5×25 0.040 1430
3300 16×25 0.038 1900 16×31.5 0.034 2300
4700 16×31.5 0.034 2300 16×35.5 0.031 2550
WV 25 35
Item Impedance Ripple Impedance Ripple

ØD×L current ØD×L current
(Ω)max. (Ω)max.
(mA rms) (mA rms)
(mm) 20°
C 130°C (mm) 20°
C 130°C
μF 100kHz 100kHz 100kHz 100kHz
220 8×11.5 0.22 360 10×12.5 0.15 500
330 10×12.5 0.15 620 10×16 0.10 700
470 10×20 0.10 800 10×20 0.073 800
1000 12.5×25 0.055 1100 12.5×25 0.040 1100
2200 16×31.5 0.034 2300 16×35.5 0.031 2550
3300 16×35.5 0.031 2550 18×35.5 0.028 2800
MINIATURE TYPES
163
VB 155°C, High Temp, High Reliability

・Load life of 1000 hours at 155°C use

・For Electronic Control Unit and other high
Rated Voitafe(V) 10 16 25 35 50 63 80 100
(at 120Hz, 20°C)
tanδ 0.20 0.16 0.14 0.12 0.10 0.10 0.08 0.08
WV 10 16 25 35 50 63 80 100
Z-25°
C/Z+20°
C 3 2 2 2 2 2 2 2
Z-40°
C/Z+20°
C 4 4 4 4 4 4 4 4

C)
Unit : mm
● DRAWING

ØD 10 12.5 16 18
P 5.0 5.0 7.5 7.5
ØD+0.5 max.
P±0.5
Ød 0.6 0.6 0.8 0.8
－
β 2.0
Safety vent

Frequency 120Hz 1kHz 50kHz 100kHz≦
CV
1000 ≦ CV 0.67 0.91 0.95 1.00
1000 ≻ CV 0.50 0.83 0.91 1.00
164
VB series

WV 10 16 25 35
Item Ripple Ripple Ripple Ripple
ØD×L(mm) (mA rms) ØD×L(mm) (mA rms) ØD×L(mm) (mA rms) ØD×L(mm) (mA rms)
155°C,100kHz 155°C,100kHz 155°C,100kHz 155°C,100kHz
μF
22 10 × 12.5 200
33 10 × 12.5 225
47 10 × 12.5 250
100 10 × 12.5 250 10 × 20 400
220 10 × 16 300 12.5 × 20 500 12.5 × 25 600
330 10 × 16 300 10 × 20 400 12.5 × 25 600 16 × 25 800
470 10 × 20 400 12.5 × 20 600 16 × 25 800 16 × 31.5 1000
1000 12.5 × 25 600 16 × 25 800 16 × 31.5 1000 18 × 40 1300
2200 16 × 31.5 1000 18 × 35.5 1200
3300 18 × 35.5 1200 18 × 40 1300
4700 18 × 40 1300
WV 50 63 80 100
Item Ripple Ripple Ripple Ripple

ØD×L(mm) (mA rms) ØD×L(mm) (mA rms) ØD×L(mm) (mA rms) ØD×L(mm) (mA rms)
155°C,100kHz 155°C,100kHz 155°C,100kHz 155°C,100kHz
μF
22 10 × 12.5 390
33 10 × 12.5 420 10 × 16 510
47 10 × 16 550 10 × 20 640
56 10 × 12.5 430 10 × 20 690 10 × 20 640
68 10 × 16 560 10 × 20 690 12.5 × 20 760
100 10 ×16 380 10 × 20 710 12.5 × 20 820 12.5 × 25 950
220 12.5 ×20 640 12.5 × 25 1040 16 × 25 1250 16 × 31.5 1380
330 16 ×20 770 16 × 20 1080 16 × 31.5 1480 18 × 31.5 1430
470 16 ×25 960 16 × 25 1280 18 × 31.5 1530
MINIATURE TYPES
560 16 ×31.5 1080 16 × 31.5 1520
680 18 ×25 1190 16 × 35.5 1520
1000 18 ×31.5 1420
165
NP Non-Polarized
WV≦100V
・Standard non-polarized series

・Designed for use in circuits with reversing polarity
・Higher voltage ratings available up to 250V
WV 6.3 10 16 25 35 50 63 80 100 160 200,250
(at 120Hz, 20°C)
tanδ 0.25 0.23 0.20 0.15 0.15 0.12 0.12 0.12 0.12 0.15 0.20
WV 6.3 10 16 25~100 160~250

C/Z+20°
C 4 3 2 2 3
Z-40°
C/Z+20°
C 10 8 6 4 5

Load life
Shelf life (at 85°
C)
ØD 5 6.3 8 10 12.5 16 18 22
ØD+αmax.
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0

P±0.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0
β 1.5 2.0 3.0
α 0.5 1.0

Frequency 50Hz 120Hz 1kHz 10kHz≦
μF
~ 47 0.75 1.00 1.55 2.00
68 ~ 680 0.80 1.00 1.34 1.50
1000 ~ 0.85 1.00 1.13 1.15
166
NP series

WV
μF
6.3 10 16 25 35 50 63 80 100 160 200 250
5 × 11 5 × 11 5 × 11 5 × 11
1.0
18 18 18 18
5 × 11 5 × 11 5 × 11 5 × 11
1.5
21 21 21 21
5 × 11 5 × 11 5 × 11 5 × 11
2.2
26 26 26 26
5 × 11 5 × 11 5 × 11 5 × 11 10 × 16 10 × 16 10 × 20
3.3
32 32 32 32 49 42 46
5 × 11 5 × 11 5 × 11 6.3 × 11 10 × 16 10 × 20 12.5 × 20
4.7
38 38 38 44 59 55 63
5 × 11 5 × 11 6.3 × 11 8 × 11.5 10 × 20 12.5 × 20 12.5 × 20
6.8
46 46 52 62 77 78 78
5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 12.5 × 20 12.5 × 20 12.5 × 25
10
55 64 64 75 109 95 103
5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 12.5 × 20 12.5 × 25 16 × 25
15
61 78 78 92 107 134 127 140
5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 12.5 × 25 16 × 25 16 × 31.5
22
73 84 94 111 129 142 177 170 186
5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 16 × 25 16 × 35.5 18 × 35.5
33
78 103 103 136 158 173 189 240 239 256
5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 12.5 × 20 16 × 35.5 18 × 40
47
87 107 123 145 189 207 226 265 329 321
5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 12.5 × 20 12.5 × 25 18 × 35.5
68
100 120 129 175 203 249 272 319 348 425
6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20 16 × 25
100
139 145 184 247 270 329 329 387 468
6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20 12.5 × 25 16 × 25
150
171 210 262 331 361 404 474 516 573
8 × 11.5 10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 35.5
220
244 295 347 437 437 574 625 694 797
10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20 16 × 25 16 × 25 16 × 35.5 18 × 40
330
347 396 464 535 628 850 850 976 1098
10 × 16 10 × 20 10 × 20 12.5 × 20 12.5 × 25 16 × 31.5 16 × 35.5 18 × 40 22 × 41
MINIATURE TYPES
470
454 516 553 750 818 1110 1164 1311 1443
10 × 20 12.5 × 20 12.5 × 20 12.5 × 25 16 × 25 18 × 35.5 18 × 40 22 × 41
680
595 729 781 984 1091 1503 1577 1736
12.5 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 35.5 18 × 40 22 × 41
1000
847 883 1033 1323 1519 1912 2105
12.5 × 20 12.5 × 25 16 × 25 16 × 35.5 18 × 40 22 × 41
1500
999 1132 1338 1748 1968 2386
12.5 × 25 16 × 25 16 × 35.5 18 × 40 22 × 41
2200
1272 1463 1781 2254 2481
16 × 25 16 × 35.5 18 × 40 22 × 41
3300
1672 1985 2360 2890
16 × 35.5 18 × 40 22 × 41
4700
2221 2579 2987
18 × 41 22 × 41
6800
2840 3214
22 × 41 Case size ØD×L (mm)
10000
3516 Ripple current (mA rms) at 85°
C, 120Hz
167
NS Non-Polarized, Height 7mmL

・Non-polarized series with 7mmL height

C
Dissipation factor max. WV 6.3 10 16 25 35 40 50 63
(at 120Hz, 20°C) tanδ 0.24 0.20 0.17 0.16 0.15 0.14 0.12 0.10
WV 6.3 10 16~25 35~63

C/Z+20°
C 4 3 2 2
Z-40°
C/Z+20°
C 8 6 4 4

Load life
Shelf life (at 85°
Unit : mm
● DRAWING
ØD 4 5 6.3
ØD+0.5 max.
P 1.5 2.0 2.5

P±0.5
Ød 0.45 0.5 0.5
β 1.0 1.5

WV 6.3 10 16 25 35 40 50 63
μF
1.0 4×7 13 4×7 14
1.5 4×7 16 4×7 17
2.2 4×7 19 5×7 24
3.3 4×7 20 4×7 21 4×7 18 5×7 27 6.3×7 34
4.7 4×7 23 4×7 24 5×7 29 5×7 25 6.3×7 37 6.3×7 40
6.8 4×7 26 5×7 32 5×7 33 6.3×7 39 5×7 29
10 4×7 31 5×7 39 6.3×7 47 6.3×7 48 6.3×7 41
15 4×7 35 5×7 44 6.3×7 55
22 5×7 49 6.3×7 62 6.3×7 67 Ripple current (mA rms) at 85°
C, 120Hz
33 6.3×7 69 6.3×7 76 Case size ØD×L (mm)
47 6.3×7 83

Coefficient 0.75 1.00 1.55 2.00
168
NE Non-Polarized, Height 5mmL

Series Miniaturized Non-polarized Solvent Proof
・Non-polarized and low profile series with 5mmL height

・Uniquely designed for use in lightweight
and portable equipment
(at 120Hz, 20°C) tanδ 0.24 0.20 0.17 0.17 0.15 0.15
WV 6.3 10 16, 25 35, 50

C/Z+20°
C 4 3 2 2
Z-40°
C/Z+20°
C 8 6 4 3

Load life
Shelf life (at 85°
C)
ØD 4 5 6.3
ØD+0.5 max.
P 1.5 2.0 2.5

P±0.5
Ød 0.45 0.45 0.45
β 1.0 1.5
● DIMENSIONS & MAXIMUM PERMISSIBLE RIPPLE CURRENT MINIATURE TYPES

μF WV 6.3 10 16 25 35 50
1.0 4×5 10
1.5 4×5 12
2.2 4×5 14 4×5 15 5×5 17
3.3 5×5 20 5×5 21 5×5 21
4.7 4×5 21 5×5 24 5×5 25 6.3×5 30
6.8 5×5 29 6.3×5 33 6.3×5 36 6.3×5 36
10 4×5 28 5×5 35 6.3×5 41 6.3×5 43
15 4×5 31 5×5 39 6.3×5 50
22 5×5 43 6.3×5 55 6.3×5 60 Ripple current (mA rms) at 85°
C, 120Hz
33 6.3×5 62 6.3×5 68
47 6.3×5 74

Coefficient 0.75 1.00 1.55 2.00
169
BP For Speaker Networks

・Non-polarized series for crossover networks in Hi-Fi sound systems

・Excellent frequency characteristics
・Close capacitance tolerance
・Extended voltage range of 25V, 50V, 100V, 200V
Series BP
Dissipation factor max. Frequency 25WV, 50WV, 100WV 200WV
(at 120Hz, 20°C) 1kHz 0.10 0.12
5kHz 0.15 0.30

Load life
Shelf life (at 85°
ØD 8 10 12.5 16 18 22
ØD+αmax.
P 3.5 5.0 5.0 7.5 7.5 10.0

P±0.5 Ød 0.6 0.6 0.6 0.8 0.8 1.0
β 1.5 2.0 3.0
L+βmax. 15 min. 4 min. α 0.5 1.0
Safety vent

μF
1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100
WV
8× 11.5 8× 11.5 10× 12.5 10× 12.5 10× 12.5 10× 16 10× 20 10× 20 10× 20 12.5× 20 12.5× 25
25
67 82 114 139 166 222 297 364 440 678 890
8× 11.5 8× 11.5 10× 12.5 10× 12.5 10× 12.5 10× 16 10× 20 10× 20 10× 20 12.5× 20 12.5× 25 16× 31.5 16× 35.5
50
67 82 114 139 166 222 297 364 440 678 890 950 1170
10× 16 10× 16 10× 16 10× 16 10× 16 10× 20 12.5× 20 12.5× 20 12.5× 25 16× 25 16× 31.5 16× 35.5 16× 40
100
100 125 150 185 225 275 340 420 543 737 790 983 1253
16× 25 16× 31.5 16× 35.5 16× 40 18× 40 22× 40
200
403 540 687 884 920 1218

C, 1kHz
170
RN Non-Polarized, Wide Temperature Range

・Wide operating temperature range of -40 ~ +105° C

・Designed for use in circuits with reversing polarity
WV 6.3 10 16 25 35 50 63 80 100
(at 120Hz, 20°C)
tanδ 0.24 0.20 0.16 0.16 0.14 0.12 0.12 0.12 0.12
WV 6.3 10 16 25 ~ 100
C/Z+20°
C 4 3 2 2
Z-40°
C/Z+20°
C 8 6 4 3
Load life
C)
ØD 5 6.3 8 10 12.5 16 18 22
ØD+αmax.
P 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0

P±0.5
Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0
MINIATURE TYPES
β 1.5 2.0 3.0
α 0.5 1.0

μF
~ 47 0.75 1.00 1.55 2.00
68 ~ 680 0.80 1.00 1.34 1.50
1000 ~ 0.85 1.00 1.13 1.15
171
RN series

WV
μF
6.3 10 16 25 35 50 63 80 100
5 × 11 5 × 11 5 × 11 5 × 11
1.0
11 12 12 13
5 × 11 5 × 11 5 × 11 5 × 11
1.5
14 15 15 16
5 × 11 5 × 11 5 × 11 5 × 11
2.2
17 18 18 19
5 × 11 5 × 11 6.3 × 11 6.3 × 11
3.3
21 23 26 27
5 × 11 5 × 11 6.3 × 11 6.3 × 11 8 × 11.5
4.7 23 25 31 31 39
5 × 11 5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5
6.8 27
26 34 37 44 54
5 × 11 5 × 11 6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 12.5
10 38
31 31 41 53 62 65
5 × 11 5 × 11 6.3 × 11 8 × 11.5 8 × 11.5 10 × 12.5 10 × 12.5 10 × 16
15 55
34 38 44 60 76 76 88
5 × 11 5 × 11 6.3 × 11 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16 10 × 16
22 67
38 41 53 63 84 101 101
5 × 11 6.3 × 11 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16 10 × 16 10 × 20
33 95
46 58 77 77 113 124 135
6.3 × 11 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20
47 125
63 69 92 106 147 161 189
6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20 12.5 × 25
68 164
76 98 128 140 177 227 248
8 × 11.5 10 × 12.5 10 × 16 10 × 20 10 × 20 12.5 × 20 12.5 × 25 16 × 25
100 198
109 139 170 185 251 300 333
10 × 12.5 10 × 16 10 × 20 12.5 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 35.5
150 285
155 186 227 267 336 408 468
10 × 12.5 10 × 20 12.5 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 35.5 18 × 35.5
220 376
188 246 323 323 451 567 609
10 × 16 12.5 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 35.5 18 × 35.5 18 × 40
330 511
252 354 396 431 634 745 782
10 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 35.5 18 × 35.5 18 × 40 22 × 41
470 701
328 422 515 571 812 933 1027
12.5 × 20 12.5 × 25 16 × 25 16 × 35.5 18 × 35.5 18 × 40 22 × 41
680 904
464 554 687 788 1025 1236
12.5 × 25 16 × 25 16 × 35.5 18 × 35.5 18 × 40 22 × 41
1000 1151
613 745 956 1026 1368
16 × 25 16 × 35.5 18 × 35.5 18 × 40 22 × 41
1500 1451
800 999 1184 1243
16 × 35.5 18 × 35.5 18 × 40 22 × 41
2200
1072 1242 1428 1572
18 × 35.5 18 × 40 22 × 41 Case size ØD×L (mm)
3300 Ripple current (mA rms) at 105°
C, 120Hz
1361 1534 1835
18 × 40 22 × 41
4700
1650 1942
22 × 41
6800
2060
172
BR For Speaker Networks

Series Non-polarized
・Non-polarized series for crossover networks in Hi-Fi sound systems

・Excellent frequency characteristics
・Close capacitance tolerance
Series BR
Dissipation factor max. Frequency 200WV
(at 120Hz, 20°C) 1kHz 0.12
5kHz 0.30

Load life

ØD+0.5 max.
ØD 10 12.5 16 18
P±0.5 P 5.0 5.0 7.5 7.5
Ød 0.6 0.6 0.8 0.8
MINIATURE TYPES
L+2.0 max. 15 min. 4 min.
Safety vent

μF
3.3 4.7 6.8 10 15 22 33 47 68 100
WV
10× 16 10× 20 12.5× 20 12.5× 20 12.5× 25 16× 25 18× 25 18× 40 18× 40 18× 40
200
185 250 300 340 420 650 730 920 935 950

C, 1kHz
173
NF For Horizontal Deflection Current Correction

・Designed for horizontal deflection current correction in TV,

monitor or computer
・Stable characteristics at high frequency and high ripple current
C
Capacitance tolerance ±10, ±20% at 120Hz, 20°
C
Dissipation factor max. 0.04 max. at 120Hz, 20°
C

C/Z+20°
C 1.5
C/Z+20°
C 3.0

Load life
(after application of DC 12V
superimposed with specified tanδ Less than 200% of specified value
ripple current) Test method Polarity reverse each 250 hours
NF series are for 2000 hours at 85°
C
Shelf life (at 85°

ØD+0.5 max.
ØD 10 12.5 16 18
P±0.5 P 5.0 5.0 7.5 7.5
Ød 0.6 0.6 0.8 0.8
Safety vent

μF
1. 0 1. 5 2.2 3.3 4.7 6.8 8.2 10
WV
10× 20 12.5× 20 12.5× 25 16× 25 16× 31.5 16× 35.5 16× 40 18 ×40
25, 50
1.8 2.4 3.3 4.5 6.0 8.0 9.0 10.0
Ripple current (Ap-p) at 85°
C, 15.75kHz
174
NH For Horizontal Deflection Current Correction

・Designed for horizontal deflection current correction in TV,

monitor or computer
・Stable characteristics at high frequency and high ripple current
C
Capacitance tolerance ±10, ±20% at 120Hz, 20°
C
Dissipation factor max. 0.04 max. at 120Hz, 20°
C
C/Z+20°
C 1.5
C/Z+20°
C 3.0

Load life
(after application of DC 12V
superimposed with specified tanδ Less than 200% of specified value
ripple current) Test method Polarity reverse each 250 hours
NH series are for 2000 hours at 105°
C

ØD+0.5 max.
ØD 10 12.5 16 18
P±0.5 P 5.0 5.0 7.5 7.5
MINIATURE TYPES
Ød 0.6 0.6 0.8 0.8
Safety vent

μF
1. 0 1. 5 2.2 3.3 4.7 6.8 8.2 10
WV
10× 20 12.5× 20 12.5× 25 16× 25 16× 31.5 16 ×35.5 16 ×40 18 ×40
25, 50
2.3 3.1 4.8 6.5 8.6 10.6 10.4 10.7
Ripple current (Ap-p) at 85°
C, 15.75kHz
175
LL Low Leakage Current

Series Low Leakage
Current
Solvent Proof
・Standard low leakage current series

・Suited for high gain audio coupling applications
・Stable leakage current characteristics for a long period of use
・Voltage range of 10 ~ 100V
Leakage current max. I = 0.002CV or 0.4μA whichever is greater (after 2 minutes)
(at 120Hz, 20°C)
tanδ 0.17 0.15 0.12 0.12 0.12 0.10 0.09 0.09
WV 10~25 35 40 50 63 100
C/Z+20°
C 2 1.75 1.75 1.5 1.5 1.5
Z-40°
C/Z+20°
C 4 4 4 2 2 2

Load life WV≦16 WV > 16
(after application of the rated Capacitance change ØD≦6.3 ±20% ±20%
voltage for 2000 hours at 85° C) ØD > 6.3 ±20% ±15%
Shelf life (at 85°

ØD+0.5 max.
＋ ØD 5 6.3 8 10 12.5 16 18
－ P±0.5 P 2.0 2.5 3.5 5.0 5.0 7.5 7.5

Ød 0.5 0.5 0.6 0.6 0.6 0.8 0.8
β 1.5 2.0

μF
~ 47 0.75 1.00 1.55 2.00
68 ~ 680 0.80 1.00 1.35 1.50
1000 ~ 0.85 1.00 1.15 1.15
176
LL series

μF WV 10 16 25 35
1.0
1.5
2.2
3.3
4.7
6.8 5 × 11 46
10 5 × 11 55 5 × 11 55
15 5 × 11 61 5 × 11 68 5 × 11 68
22 69 5 × 11 73 5 × 11 82 6.3 × 11 94
33 5 × 11 84 5 × 11 90 6.3 × 11 116 6.3 × 11 116
47 5 × 11 101 6.3 × 11 123 8 × 11.5 163 8 × 11.5 163
68 6.3 × 11 139 6.3 × 11 148 8 × 11.5 196 10 × 12.5 227
100 6.3 × 11 169 8 × 11.5 212 10 × 12.5 276 10 × 16 302
150 8 × 11.5 244 10 × 12.5 302 10 × 16 370 10 × 20 404
220 10 × 12.5 344 10 × 16 401 10 × 20 489 12.5 × 20 574
330 10 × 16 461 10 × 20 535 12.5 × 20 703 12.5 × 25 766
470 10 × 20 600 12.5 × 20 750 12.5 × 25 914 12.5 × 25 914
680 12.5 × 20 847 12.5 × 20 902 12.5 × 25 1100 16 × 25 1220
1000 12.5 × 20 1028 12.5 × 25 1193 16 × 25 1480 16 × 31.5 1619
1500 12.5 × 25 1298 16 × 25 1522 16 × 31.5 1835 18 × 35.5 2066
2200 16 × 25 1659 16 × 31.5 1908 18 × 35.5 2341
3300 16 × 31.5 2124 18 × 35.5 2502
4700 18 × 35.5 2737

C, 120Hz
μF WV 40 50 63 100
1.0 5 × 11 20 5 × 11 18
1.5 5 × 11 25 5 × 11 22
2.2 5 × 11 30 5 × 11 26
3.3 5 × 11 35 5 × 11 37 5 × 11 32
4.7 5 × 11 38 5 × 11 42 5 × 11 44 5 × 11 38
6.8 5 × 11 46 5 × 11 50 5 × 11 53 6.3 × 11 53
10 5 × 11 55 6.3 × 11 70 6.3 × 11 73 8 × 11.5 76
15 6.3 × 11 78 6.3 × 11 85 8 × 11.5 106 8 × 11.5 93
22 6.3 × 11 94 8 × 11.5 122 8 × 11.5 129 10 × 12.5 130
33 8 × 11.5 136 8 × 11.5 149 10 × 12.5 183 10 × 16 175
47 8 × 11.5 163 10 × 12.5 207 10 × 16 239 10 × 20 227
68 10 × 12.5 227 10 × 16 273 10 × 20 314 12.5 × 20 313
100 10 × 16 302 10 × 20 361 12.5 × 20 447 12.5 × 25 380
MINIATURE TYPES
150 10 × 20 404 12.5 × 20 519 12.5 × 25 596 16 × 25 508
220 12.5 × 20 475 12.5 × 25 685 16 × 25 801 16 × 31.5 699
330 12.5 × 25 766 16 × 25 931 16 × 31.5 1074 16 × 35.5 983
470 16 × 25 1014 16 × 31.5 1216 16 × 35.5 1345 18 × 40 1320
680 16 × 25 1220 18 × 35.5 1534 18 × 40 1821
1000 16 × 31.5 1699 18 × 40 2095
1500 18 × 40 2168

C, 120Hz
177
LS Low Leakage Current, Height 7mmL

Series Low Leakage
Current
Solvent Proof
・Low leakage current series with 7mmL height

C
Dissipation factor max. WV 6.3 10 16 25 35 40 50 63
(at 120Hz, 20°C) tanδ 0.24 0.20 0.16 0.14 0.12 0.12 0.10 0.10
WV 6.3 10 16, 25 35 ~ 63
Z-25°
C/Z+20°
C 4 3 2 2
Z-40°
C/Z+20°
C 8 6 4 3

Shelf life (at 85°
C)
ØD 4 5 6.3
ØD+0.5 max.
＋
P 1.5 2.0 2.5
－ P±0.5
Ød 0.45 0.5 0.5
β 1.0 1.5

WV 6.3 10 16 25 35 40 50 63
μF
1.0 4×7 14 4×7 14
1.5 4×7 17 4×7 17
2.2 4×7 21 4×7 21
3.3 4×7 25 5×7 29
4.7 4×7 28 4×7 28 5×7 35 6.3×7 40
6.8 4×7 31 5×7 38 5×7 39 5×7 42 6.3×7 49
10 4×7 35 5×7 43 5×7 46 5×7 47 6.3×7 59
15 4×7 38 5×7 49 5×7 53 6.3×7 66 6.3×7 66 6.3×7 72
22 4×7 43 5×7 53 5×7 60 6.3×7 74 6.3×7 80 6.3×7 79
33 5×7 60 5×7 65 6.3×7 85 6.3×7 91
47 5×7 71 6.3×7 90 6.3×7 101
68 6.3×7 99 6.3×7 109 Ripple current (mA rms) at 85°
C, 120Hz
100 6.3×7 120 Case size ØD×L (mm)

Frequency
μF 50Hz 120Hz 1kHz 10kHz≦
~ 47 0.75 1.00 1.55 2.00
68 ~ 0.80 1.00 1.35 1.50
178
LE Low Leakage Current, Height 5mmL

Series Low Leakage Miniaturized Solvent Proof
Current
・Low leakage current series with 5mmL height

・Designed for use in lightweight and
portable equipment
(at 120Hz, 20°C) tanδ 0.35 0.24 0.20 0.16 0.14 0.12 0.10
WV 4 6.3 10 16 25 35, 50
C/Z+20°
C 7 4 3 2 2 2
Z-40°
C/Z+20°
C 15 10 8 6 4 3
Shelf life (at 85°
C)

ØD+0.5 max.
＋ ØD 4 5 6.3
－ P±0.5 P 1.5 2.0 2.5
Ød 0.45 0.45 0.45
15 min. 4 min.
β 1.0 1.5
L+βmax.
MINIATURE TYPES
WV 4 6.3 10 16 25 35 50
μF
1.0 4×5 12
1.5 4×5 15
2.2 4×5 18
3.3 4×5 22
4.7 4×5 25 5×5 31
6.8 4×5 27 5×5 34 6.3×5 44
10 4×5 31 5×5 38 5×5 42 6.3×5 53
15 4×5 34 5×5 44 6.3×5 55 6.3×5 59
22 4×5 37 5×5 47 6.3×5 62 6.3×5 66
33 5×5 44 5×5 53 6.3×5 68 6.3×5 76
47 5×5 52 6.3×5 74 6.3×5 81
68 6.3×5 74 6.3×5 89 Ripple current (mA rms) at 85°
C, 120Hz
100 6.3×5 89 Case size ØD×L (mm)

Frequency
~ 47 0.75 1.00 1.55 2.00
68 ~ 0.80 1.00 1.35 1.50
179
RL Low Leakage Current, Wide Temperature

Range Series Low Leakage
Current
Solvent Proof
・Low leakage current series

・Wide operating temperature range of -55 ~ +105°
C
・For Hi-Fi sound audio systems
(at 120Hz, 20°C) tanδ 0.15 0.12 0.08 0.08 0.08 0.08
WV 10 16 25~50
Z-25°
C/Z+20°
C 2 2 1.5
Z-40°
C/Z+20°
C 4 3 2

C)

ØD+0.5 max.
＋ ØD 5 6.3 8 10
－ P±0.5 P 2.0 2.5 3.5 5.0
Ød 0.5 0.5 0.6 0.6
L+βmax. 15 min. 4 min. β 1.5 2.0

μF WV 10 16 25 35 40 50
1.0 5×11 14
1.5 5×11 17
2.2 5×11 21
3.3 5×11 25
4.7 5×11 30
6.8 5×11 36
10 5×11 44 5×11 44
15 5×11 54 6.3×11 62 6.3×11 62
22 5×11 65 6.3×11 75 6.3×11 75 6.3×11 75
33 5×11 65 6.3×11 92 6.3×11 92 8×11.5 109 8×11.5 109
47 5×11 70 6.3×11 90 6.3×11 110 8×11.5 129 8×11.5 129 8×11.5 129
68 6.3×11 96 6.3×11 108 8×11.5 156 8×11.5 156 10×12.5 181 10×12.5 181
100 6.3×11 117 8×11.5 154 8×11.5 189 10×12.5 219
150 8×11.5 169 8×11.5 189 10×12.5 269
220 8×11.5 205 10×12.5 266 Ripple current (mA rms) at 105°
C, 120Hz
330 10×12.5 291 Case size ØD×L (mm)

Frequency
~ 47 0.75 1.00 1.55 2.00
68 ~ 0.80 1.00 1.35 1.50
180

NEW
VM,VL For Refolw

WV≦100V

・VM series is load life of 5000 hours at 105°C
・VL series is load life of 8000 hours at 105°
C
Operating temperature range -40 ~ 105°
C
WV ≦ 100 WV > 100
I = 0.01CV or 3μ
A whichever is greater (after 2 min.) I = 0.02CV + 25μA (after 5 min.)
C
(at 120Hz, 20°C) tanδ 0.16 0.13 0.12 0.08 0.14 0.20
Low temperature characteristics WV 25 35 50 100 160 250

C/Z+20°
C 5 4 3 3 6 8
After application of the rated voltage 5000(VM), 8000(VL) hours at 105° C
Load life
C) The measurement shall be performed after exposure for 24 hours at room temperature after
application of DC reted voltage to the capacitors for 30 minutes.

ØD+0.5 max.
＋ ØD 8 10
－ P±0.5 P 3.5 5.0

Ød 0.5 0.6
β 1.5 2.0
Safety vent
MINIATURE TYPES
μF WV 25 35 50 100 160 250
15 8 × 20 375
22 8 × 20 375 10 × 16 469
33 8 × 20 469 10 × 20 625
47 10 × 20 625
68 8 × 20 630
82 10 × 16 725
100 10 × 20 830
180 8 × 20 760
220 10 × 16 810
330 10 × 20 890
470 8 × 20 780 8 × 20 810
560 8 × 20 930 10 × 20 1029
680 10 × 16 1089 10 × 20 1295 Ripple current (mA rms) at 105°
C, 100kHz
820 10 × 20 1351 Case size ØD×L (mm)
1000 10 × 20 1600

Frequency 120Hz 300Hz 1kHz 10kHz 100kHz≦
μF
~ 33 0.32 0.60 0.80 0.90 1.00
39 ~ 270 0.40 0.63 0.82 0.91 1.00
330 ~ 1000 0.45 0.67 0.84 0.92 1.00
Refer to page 182 for soldering recommendation.
181
Reflow soldering method for series of VM, VL
1. Recommended conditions for reflow soldering

The aluminum electrolytic capacitor is subjected to soldering by reflow method.
Temperature and time conditions of reflow soldering shall be set as per each temperature profile shown below
as a standard. The following are recommended conditions in the case of reflow soldering method for the
aluminum electrolytic capacitor.
(1) The capacitor shall not be subjected to either flow or dip soldering method.
(2) Avoid soldering twice by reflow. The number of reflow time for aluminum electrolytic capacitor shall be once
basically. If this type of capacitor has to be inevitably subjected to the reflow twice, enough cooling time between
the first and the second reflow (at least more than 30 minutes) shall be taken to avoid the consecutive reflows
by all means.
(3) On setting the reflow conditions, it shall be done lest the temperature at surface of the capacitor should exceed
more than 175°
C
2. RECOMMENDED REFLOW SOLDERING CONDITIONS
Tp
Tp
TL
Ramp-up
Ts max.
tL
Ts min.
Ramp down
Preheat
0
Ts (150°
C max., 120sec.max)
Time (sec.)
t (25°
C to Peak)
Soldering condition
Profile Feature
Ø8 ~ Ø10
Average Ramp-up Rate (TL to TP) 2°
C / second max.
Temperature Min. (TS min) 100°C
Preheat Temperature Max. (TS max) 125°C
Time (TS min to TS max) 60 ~ 90 seconds
TS max to TL - Ramp-up Rate 2°
C / second max.
Time maintained Temperature (TL) 140°C
above Time (tL) 40 ~ 60 seconds
Peak/classification Temperature (TP) 175°C
Time within 5°
C of actual peak temperature(TP) 10 seconds max.
Ramp-Down rate 3°
C / second max.
Time 25° C to peak temperature 6 minute max.
182
5 LARGE ALUMINUM ELECTROLYTIC CAPACITORS
LARGE ALUMINUM ELECTROLYTIC CAPACITORS
PART NUMBER SYSTEM
Part Number System
Series Name Rated Voltage Capacitance Cap. Tol. Case Diameter Case Height Terminal Internal Control
Configurations Code
Series Name
See page 7. Case Diameter
ex) 22 22
25.4 25
30 30
35 35
Rated Working Voltage 40 40
51 51
WV 6.3 10 16 25 35 63.5 64
Code 0J 1A 1C 1E 1V 76.2 76
89 89
WV 40 50 63 80 100
Code 1G 1H 1J 1K 2A
Case Height
WV 160 200 220 250 315
ex) 30mm 030
Code 2C 2D 7D 2E 2F 105mm 105
WV 330 350 360 375 400
Code 2L 2V 2Z 7S 2G Terminal Configurations

WV 450 475 500 550 600 Terminal Configurations Code
Code 2W 7W 2H 7H 2X Snap-in Terminal for Terminal Length 6mm HA

PC board mounting Terminal Length 4mm HC
D 35 LC
Capacitance Lug Terminal for D = 40 LA
ex) 47 F 476 Soldering D = 51 LD
470 F 477 D 63.5 LE
4700 F 478
47000 F 479 D = 22 PK
Photo Flash D = 25.4, 30 LC
D = 35 LF
Screw Terminal Type SB
Capacitance Tolerance Screw Terminal Type (Stud Type) TB

Screw Terminal Type (M6) S6
Tolerance 0 10 10 10 10 Screw Terminal Type (Stud Type, M6) T6
(%) 10 15 20 20 20 30 50 75
Code K L M W V Q T U
184
PACKING
FIGURE 1 FIGURE 2
SNAP-IN TYPE INNER, MIDDLE BOX SCREW TYPE BOX
SNAP-IN TYPE PACKAGING Quantity (pcs) / BOX (FIGURE 1)

SIZE SNAP-IN(QUANTITY)
D L INNER BOX MIDDLE BOX
20 ~ 40
22 200 600
45 ~ 50
20 ~ 40
150 450
25 45 ~ 50
60 150 300
20 ~ 40
30 45 ~ 55 100 300
60 ~ 80
20 ~ 40
200
45 ~ 55
35 50
60 ~ 80
150
100 ~ 120
30 ~ 40
50 150
40 50
60 ~ 80
90 ~ 110 100
SCREW TYPE PACKAGING Quantity (pcs) / BOX & BOX SIZE (FIGURE 2)
SIZE SCREW
D QUANTITY
35 45
LARGE TYPES
51 23
64 16
76 12
89 9
185
SNAP-IN DRAWING
STANDARD 2 PIN ( 22~ 40) 2 PIN - 1 ( 25, 30, 35)
Type : HA, HC Type : HR

Insulating sleeve Insulating sleeve
Terminal Terminal
L 6.0 1 4.0 0.5 L 4.0 0.5
3.3 0.1
10
10
0.2 0.2 2 0.1
4.75 0.1
2 2 0.1
10 0.1
3 PIN - 1 (ONLY 25) 4 PIN ( 35, 40)
Type : KT Type : HA, HC

Insulating sleeve Insulating sleeve (4pin)
Terminal Terminal
3MAX
L 7.5 1 L 6.0 1 4.0 0.5
3- 1.3 1 Blank Blank 4 2 0.1
30 30 30
22.5
12.5 1
Blank
22.5 0.2
10 1
5 PIN (ONLY 40)
Type : KP
Insulating sleeve
Blank
20 0.1
Terminal 17.5 0.1
10 0.1
5- 1.3 0.1
20 0.1
3MAX
L 7.5 1 Blank Blank
186
SCREW CASE DRAWING

STANDARD STUD TYPE
Type : SB Type : TB
Insulation Sleeve
Insulation Bottom
“ + ” SIGN
Plate
Safety Vent
M12 BOLT
+
12
--
“ -- ” SIGN
16
(ONLY 51, , 76)
T-BOARD DRAWING
STANDARD (+) 3mm Up WILD TYPE (M6 BOLT)
M5 HEXA BOLT M5 HEXA BOLT M6 HEXA BOLT
10.0 10.0 13.0
(+) (-) 6.0 1 9.0 1 (+) (-) 6.0 1 (+) (-) 6.0 1
(ONLY 76) (ONLY 76)
STUD TYPE DRAWING

NON-INSULATED VERSION INSULATED VERSION
Stud Type
21.0 1.0
Washer
Stud Type
19.0 10.0
(7.0)
Bolt
LARGE TYPES
38.0
Stud Type Insulation Insulation

Washer Cap 17.6
Stud Type Cap
Bolt
21.5
187
Snap-in Terminal Type, Standard

HC Series Solvent Proof
WV 100V
Standard snap-in terminal type

Including 550WV products
Operating temperature range WV< 350 : -40 ~ +85 C, WV 350 : -25 ~ +85 C
Leakage current max. I=3 CV ( A) (after 5 minutes)
WV 6.3 10 16, 25 35 50, 63 80, 100 160 ~ 400 450~550
(at 120Hz, 20 C)
tan 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.20

DRAWING Unit : mm
D 40
Insulating sleeve
PC Board Terminal
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1
Shorter terminal(4.0 0.5) is also available upon request.

Terminal length of height 20mm products is applied shorter terminal to standard terminal type.
D 35, 40
PC Board
Mounting Holes
Insulating sleeve
Blank Blank
4 2 0.1
D 1 max.
30 30 30
22.5
Safety vent L 2 max. 6.0 1

22.5 0.2

Frequency
50Hz 120Hz 300Hz 1kHz 10kHz
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 250 0.85 1.00 1.20 1.25 1.45
315 ~ 0.85 1.00 1.15 1.20 1.40
188
HC series

WV 6.3 10 16
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
22 25
10000
3.32
22 25 22 30 25.4 25
12000
3.31 3.55 3.89
22 25 22 30 25.4 25 22 35 25.4 30 30 25
15000
3.39 3.82 3.39 4.29 4.45 4.56
22 30 25.4 25 22 35 25.4 25 22 40 25.4 35 30 30
18000
3.85 3.96 4.28 4.17 4.77 4.96 5.10
22 35 25.4 25 22 40 25.4 30 30 25 22 50 25.4 40 30 30
22000
4.34 4.22 4.79 4.71 4.83 5.51 5.51 5.39
22 40 25.4 30 30 25 22 45 25.4 35 30 30 25.4 45 30 35 35 25
27000
4.85 4.77 4.89 5.30 5.26 5.41 6.06 5.98 5.80
22 45 25.4 35 30 30 22 50 25.4 40 30 30 35 25 30 40 35 30
33000
5.36 5.32 5.47 5.82 5.81 5.69 5.81 6.56 6.41
22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 30 30 45 35 35
39000
5.83 5.82 5.70 5.82 6.31 6.22 6.38 7.08 6.96
25.4 45 30 35 35 30 25.4 50 30 40 35 30 30 50 35 40
47000
6.35 6.26 6.41 6.83 6.78 6.62 7.62 7.54
25.4 50 30 40 35 30 30 45 35 35 35 45 40 40
56000
6.85 6.80 6.64 7.31 7.18 8.08 8.23
30 45 35 35 35 40 35 50 40 50
68000
7.35 7.23 7.76 8.63 9.13
35 45 40 40 40 50 40 60
100000
8.34 8.49 9.35 10.2
WV 25 35 50
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
22 30 25.4 25
3300
2.97 3.06
22 30 25.4 25 22 40 25.4 35 30 25 35 25
4700
3.06 2.98 3.83 3.98 3.86 4.19
22 25 22 35 25.4 30 22 45 25.4 40 30 30 35 25
5600
2.65 3.28 3.39 4.26 4.44 4.35 4.44
22 30 25.4 25 22 40 25.4 30 30 25 22 50 25.4 40 30 35 35 30
6800
3.06 3.15 3.73 3.67 3.76 4.77 4.76 4.92 5.04
22 35 25.4 30 22 45 25.4 35 30 30 25.4 50 30 40 35 30
8200
3.45 3.57 4.13 4.10 4.22 5.43 5.38 5.26
22 40 25.4 30 30 25 22 50 25.4 40 30 30 30 45 35 35
10000
3.95 3.89 3.99 4.68 4.68 4.58 6.07 5.97
22 45 25.4 35 30 30 25.4 45 30 35 35 30 30 50 35 40
12000
4.41 4.37 4.50 5.18 5.11 5.24 6.62 6.55
22 50 25.4 40 30 35 30 40 35 35 35 45
15000
4.94 4.94 5.10 5.72 5.88 7.20
25.4 45 30 35 35 30 30 45 35 40 35 50 40 40
18000
5.45 5.38 5.51 6.28 6.46 7.74 7.62
30 45 35 35 35 45 40 40 40 50
22000
6.22 6.12 7.07 7.20 8.54
30 50 35 40 40 50 40 60
27000
6.82 6.74 8.14 9.45
35 45 40 40 40 50
33000
7.35 7.48 8.46
WV 63 80 100
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
22 25 22 30 25.4 25
1200
2.24 2.39 2.46
22 30 22 35 25.4 30 30 25
1500
2.67 2.83 2.93 3.00
22 25 22 30 25.4 25 22 40 25.4 35 30 30
1800
2.20 2.92 3.01 3.26 3.39 3.49
22 30 25.4 25 22 35 25.4 30 30 25 22 45 25.4 40 30 30
2200
2.50 2.58 3.25 3.36 3.45 3.58 3.74 3.66
22 35 25.4 30 22 40 25.4 35 30 30 25.4 45 30 35 35 30
2700
2.94 3.04 3.79 3.94 4.05 4.33 4.27 4.37
22 35 25.4 30 30 25 22 45 25.4 40 30 30 25.4 50 30 40 35 35
3300
3.14 3.26 3.34 4.18 4.36 4.27 4.76 4.72 4.85
LARGE TYPES
22 40 25.4 35 30 30 22 50 25.4 45 30 35 30 45 35 35
3900
3.60 3.74 3.85 4.75 4.96 4.89 5.36 5.27
22 50 25.4 40 30 35 35 30 25.4 50 30 40 35 30 30 50 35 40
4700
4.19 4.19 4.10 4.19 5.44 5.39 5.27 5.86 5.80
25.4 45 30 35 35 30 30 45 35 35 35 45 40 40
5600
4.65 4.58 4.70 5.91 5.81 6.34 6.45
25.4 50 30 40 35 30 35 40 40 50
6800
5.20 5.16 5.04 6.45 7.40
30 45 35 35 35 45 40 40 40 50
8200
5.62 5.53 6.91 7.04 7.60
30 50 35 40 40 50 Case size D L (mm)
10000
6.32 6.25 8.14 Ripple current (Arms) at 85 C, 120Hz
35 45 40 40
12000
6.83 6.95
189
HC series
WV 160 200 250
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
150
22 25 25.4 20
0.90 0.92
180
22 20 22 25 25.4 20
0.91 0.90 1.01
220
22 20 22 25 25.4 20 22 25 25.4 25 30 20
1.01 1.09 1.11 1.09 1.19 1.22
270
22 25 25.4 20 22 25 25.4 25 30 20 22 30 25.4 25 30 20
1.20 1.32 1.20 1.32 1.35 1.28 1.32 1.35
330
22 25 25.4 20 22 30 25.4 25 30 20 22 30 25.4 30 30 20
1.33 1.36 1.42 1.46 1.49 1.42 1.56 1.49
390
22 25 25.4 25 30 20 22 30 25.4 25 30 25 22 35 25.4 30 30 25
1.45 1.59 1.62 1.54 1.59 1.74 1.63 1.69 1.73
470
22 30 25.4 25 30 20 22 35 25.4 30 30 25 22 40 25.4 30 30 25 35 25
1.69 1.75 1.78 1.79 1.86 1.90 1.89 1.84 1.90 2.06
560
22 35 25.4 30 30 25 22 40 25.4 35 30 25 35 25 22 50 25.4 40 30 30 35 25
1.96 2.03 2.08 2.06 2.14 2.08 2.25 2.26 2.25 2.20 2.25
680
22 40 25.4 30 30 25 22 45 25.4 40 30 30 35 25 25.4 45 30 35 35 30
2.27 2.23 2.29 2.38 2.48 2.43 2.48 2.60 2.56 2.62
820
22 45 25.4 35 30 30 35 25 22 50 25.4 45 30 35 35 30 25.4 45 30 40 35 30
2.61 2.59 2.67 2.73 2.73 2.85 2.81 2.88 2.82 2.95 2.88
1000
22 50 25.4 40 30 30 35 25 30 40 35 30 30 45 35 35
3.01 3.01 2.95 3.01 3.26 3.18 3.40 3.35
1200
25.4 45 30 35 35 30 30 45 35 35 35 40 40 40
3.23 3.18 3.26 3.49 3.43 3.59 3.81
1500
30 40 35 35 30 50 35 40 35 50 40 50
3.73 3.83 4.06 4.01 4.35 4.60
1800
35 40 40 40 35 45 40 40 40 60
4.39 4.66 4.58 4.66 5.39
WV 315 350 400
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
68
22 20 25.4 20
0.56 0.61
82
22 20 22 25 25.4 20
0.62 0.66 0.68
100
22 20 22 25 25.4 20 22 25 25.4 25 30 20
0.68 0.73 0.75 0.74 0.81 0.82
120
22 25 25.4 20 22 25 25.4 25 30 20 22 30 25.4 25 30 20
0.80 0.82 0.81 0.88 0.90 0.86 0.88 0.90
150
22 25 25.4 25 30 20 22 30 25.4 25 30 20 22 30 25.4 30 30 25
0.89 0.99 1.01 0.96 0.97 1.01 0.96 1.05 1.08
180
22 30 25.4 25 30 20 22 35 25.4 30 30 25 22 40 25.4 35 30 25 35 25
1.05 1.07 1.10 1.12 1.14 1.18 1.17 1.21 1.18 1.28
220
22 35 25.4 30 30 25 22 40 25.4 30 30 25 35 25 22 45 25.4 40 30 30 35 25
1.23 1.27 1.30 1.29 1.26 1.30 1.41 1.35 1.41 1.38 1.41
270
22 40 25.4 30 30 25 35 25 25.4 35 30 30 35 25 25.4 40 30 30 35 25
1.43 1.40 1.44 1.56 1.47 1.53 1.65 1.55 1.55 1.56
330
22 50 25.4 35 30 30 35 25 25.4 40 30 35 35 30 25.4 45 30 35 35 30
1.73 1.63 1.69 1.73 1.71 1.78 1.83 1.80 1.78 1.83
390
25.4 40 30 35 35 30 30 40 35 30 30 40 35 30
1.86 1.94 1.99 2.03 1.98 2.03 1.98
470
30 35 35 30 30 40 35 35 30 45 35 35
2.13 2.18 2.23 2.30 2.30 2.30
560
30 40 35 35 30 45 35 40 35 40 40 40
2.44 2.50 2.55 2.62 2.62 2.78
680
30 45 35 40 30 50 35 45 40 40 35 50 40 50
2.80 2.88 2.92 3.01 3.06 3.13 3.31
820
30 50 35 50 40 40 35 50 40 50 40 60
3.21 3.44 3.37 3.44 3.63 3.89
WV 450 500 550
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
22 30 25.4 25 30 20
47
0.41 0.42 0.43
22 20 22 30 25.4 30 30 25
56
0.51 0.45 0.49 0.50
22 25 25.4 20 22 25 22 35 25.4 30 30 25
68
0.60 0.61 0.46 0.52 0.53 0.55
22 30 25.4 25 30 20 22 30 25.4 25 22 40 25.4 35 30 30 35 25
82
0.71 0.72 0.74 0.54 0.55 0.60 0.62 0.64 0.66
22 30 25.4 30 30 25 22 40 25.4 30 30 25 22 45 25.4 40 30 30 35 25
100
0.78 0.85 0.88 0.66 0.66 0.67 0.70 0.72 0.71 0.73
22 35 25.4 30 30 25 25.4 40 30 30 25.4 45 30 35 35 30
120
0.91 0.93 0.96 0.78 0.78 0.83 0.82 0.84
22 40 25.4 35 30 30 35 25 30 35 25.4 50 30 40 35 35
150
1.07 1.10 1.14 1.16 0.92 0.96 0.96 0.99
25.4 35 30 30 35 25 30 40 30 45 35 35
180
1.20 1.25 1.28 1.05 1.10 1.08
25.4 40 30 35 35 30 30 45 35 40 35 45 40 40
220
1.40 1.45 1.49 1.22 1.25 1.31 1.33
30 40 35 30 35 45 35 50 40 50
270
1.62 1.65 1.44 1.51 1.59
30 45 35 35 35 45 40 50
330
1.94 1.94 1.62 1.76
30 50 35 35 35 50 40 60
390
2.21 2.09 1.80 2.05
30 50 35 40 40 40 40 50 40 60
470
2.42 2.42 2.55 2.10 2.25
35 50 40 50 40 60
560
2.84 3.00 2.45
680
3.54 2.70 Ripple current (Arms) at 85 C, 120Hz
190
Snap-in Terminal Type,

HJ Series Solvent Proof
WV 100V
High voltage, high capacitance series

Load life of 3000 hours at 85°C
WV 10 16, 25 35 50, 63 80, 100 160 ~ 400 450
(at 120Hz, 20 C)
tan 0.40 0.35 0.30 0.25 0.20 0.15 0.20

DRAWING Unit : mm
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1

LARGE TYPES

Frequency
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 250 0.85 1.00 1.20 1.25 1.45
350 ~ 0.85 1.00 1.15 1.20 1.40
191
HJ series

WV 10 16 25
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
6800
22 25
2.24
8200
22 30
2.61
10000
22 30 22 35 25.4 30 30 25
2.68 3.24 3.14 3.25
12000
22 25 22 35 25.4 25 22 40 25.4 35 30 25
2.39 3.12 3.00 3.70 3.63 3.56
15000
22 30 22 40 25.4 30 30 25 25.4 40 30 30 35 25
2.86 3.67 3.58 3.70 4.09 4.00 4.07
18000
22 35 25.4 25 22 45 25.4 35 30 25 25.4 45 30 35 35 30
3.21 3.05 4.15 4.13 3.93 4.62 4.60 4.64
22000
22 40 25.4 30 25.4 40 30 30 25.4 50 30 40 35 30
3.74 3.64 4.44 4.38 5.14 5.17 5.05
27000
22 45 25.4 35 30 25 25.4 45 30 35 35 25 30 45 35 35
4.06 3.98 3.57 4.89 4.84 4.71 5.98 5.88
33000
25.4 40 30 30 35 25 30 40 35 30 35 40
4.50 3.99 4.57 5.50 5.41 6.59
39000
25.4 45 30 30 35 30 30 45 35 35
5.17 4.55 5.18 6.19 6.09
47000
30 35 35 35 30 50 35 40
5.15 5.76 6.80 6.75
56000
30 40 35 40
5.61 6.45
WV 35 50 63
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
2200
22 30
2.15
2700
22 25 22 30 25.4 25
1.95 2.38 2.42
3300
22 30 25.4 25 22 35 25.4 30
2.40 2.35 2.72 2.74
3900
22 25 22 30 25.4 25 22 40 25.4 35 30 25
1.89 2.50 2.50 3.07 3.16 3.00
4700
22 30 25.4 25 22 35 25.4 30 30 25 22 45 25.4 40 30 30
2.29 2.26 2.91 2.98 3.01 3.44 3.55 3.51
5600
22 30 25.4 25 22 40 25.4 35 30 30 22 50 25.4 45 30 35 35 30
2.42 2.42 3.31 3.44 3.42 3.92 4.01 3.98 3.93
6800
22 35 25.4 30 30 25 22 45 25.4 40 30 35 35 25 25.4 50 30 40 35 30
2.82 2.89 2.89 3.70 3.81 3.93 3.80 4.47 4.48 4.38
8200
22 40 25.4 35 30 25 25.4 45 30 40 35 30 30 45 35 35
3.26 3.30 3.19 4.32 4.51 4.41 5.07 4.99
10000
22 45 25.4 40 30 30 35 25 25.4 50 30 45 35 35 30 50 35 40
3.57 3.65 3.60 3.60 4.83 5.04 4.88 5.75 5.68
12000
25.4 45 30 35 35 30 30 45 35 40 35 45
4.15 4.13 4.23 5.44 5.60 6.47
15000
25.4 50 30 40 35 35 35 45
4.76 4.76 4.90 6.53
18000
30 45 35 40 35 45
5.22 5.44 7.04
22000
35 45
6.28
27000
35 50
6.90
WV 80 100
D
F 22 25.4 30 35 22 25.4 30 35
1200
22 25 22 30 25.4 25
1.77 2.02 2.06
1500
22 30 25.4 25 22 35 25.4 30
2.00 2.02 2.40 2.45
1800
22 35 25.4 30 22 40 25.4 35 30 30
2.35 2.35 2.76 2.81 2.84
2200
22 40 25.4 30 30 25 22 45 25.4 40 30 30 35 25
2.86 2.79 2.85 3.00 3.10 3.06 3.13
2700
22 45 25.4 35 30 30 25.4 45 30 35 35 30
3.23 3.05 3.17 3.59 3.57 3.66
3300
22 50 25.4 40 30 30 30 40 35 35
3.18 3.28 3.24 4.15 4.18
3900
25.4 45 30 35 30 45 35 35
3.62 3.60 4.58 4.51
4700
25.4 50 30 40 35 30 35 40
4.22 4.23 4.12 5.18
5600
30 45 35 35 35 50
4.66 4.59 5.91
6800
35 40
5.20
8200
35 45
5.86
35 50 Case size D L (mm)
10000
6.61 Ripple current (A rms) at 85 C, 120Hz
192
HJ series

WV 160 200 250
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 20
150
0.97
22 20 22 20
180
0.91 1.06
22 20 22 25 25.4 20
220
1.18 1.24 1.22
22 20 22 25 25.4 20 22 25 25.4 25
270
1.30 1.37 1.35 1.50 1.32
22 25 22 25 25.4 20 22 30 25.4 25 30 20
330
1.50 1.51 1.49 1.66 1.61 1.58
22 25 25.4 20 22 25 25.4 25 30 20 22 35 25.4 30 30 25
390
1.63 1.62 1.73 1.71 1.71 1.88 1.88 1.86
22 30 25.4 20 22 30 25.4 25 30 20 22 35 25.4 35 30 25
470
1.86 1.86 1.97 1.95 1.88 2.15 2.15 2.04
22 30 25.4 25 30 20 22 35 25.4 30 30 25 22 40 25.4 35 30 25 35 25
560
2.15 2.15 2.05 2.18 2.15 2.15 2.48 2.35 2.35 2.35
22 35 25.4 30 30 25 22 40 25.4 30 30 25 35 25 22 50 25.4 40 30 30 35 25
680
2.35 2.33 2.33 2.48 2.48 2.48 2.33 2.61 2.67 2.71 2.58
22 40 25.4 30 30 25 22 45 25.4 35 30 30 35 25 25.4 45 30 35 35 30
820
2.68 2.65 2.64 2.81 2.79 2.80 2.83 3.01 2.98 2.96
22 45 25.4 35 30 30 35 25 22 50 25.4 40 30 35 35 30 30 40 35 35
1000
3.02 3.00 2.96 3.13 3.28 3.28 3.15 3.26 3.56 3.48
22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 30 30 45 35 35
1200
3.47 3.43 3.41 3.40 3.61 3.61 3.57 3.99 3.84
25.4 45 30 35 35 30 30 45 35 35 30 50 35 40
1500
3.96 3.96 3.94 4.13 4.06 4.33 4.33
30 40 35 35 30 50 35 40 35 50
1800
4.31 4.28 4.60 4.59 4.76
30 50 35 40 35 45
2200
4.96 4.96 5.25
35 45
2700
5.57
35 50
3300
6.21
WV 350 400 450
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 20
56
0.61
22 20 22 20
68
0.65 0.71
22 20 22 25 25.4 20
82
0.85 0.86 0.84
22 20 22 25 25.4 20 22 25 25.4 25
100
0.80 0.99 0.82 0.95 0.97
22 25 25.4 20 22 25 25.4 20 22 30 25.4 25 30 20
120
1.04 0.90 1.09 1.13 1.07 1.09 1.12
22 25 25.4 25 22 30 25.4 25 30 20 22 35 25.4 30 30 25
150
1.20 1.22 1.24 1.27 1.20 1.18 1.25 1.29
22 30 25.4 25 22 30 25.4 25 30 25 22 35 25.4 35 30 25
180
1.34 1.37 1.41 1.44 1.52 1.32 1.40 1.45
22 30 25.4 30 30 25 22 35 25.4 30 30 25 22 40 25.4 35 30 25 35 25
220
1.47 1.53 1.54 1.58 1.64 1.66 1.48 1.59 1.64 1.59
22 35 25.4 30 30 25 22 40 25.4 35 30 30 35 25 22 50 25.4 40 30 30 35 25
270
1.70 1.73 1.80 1.65 1.79 1.82 1.63 1.88 1.87 1.89 1.90
22 45 25.4 35 30 30 35 25 22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 30
330
1.87 1.97 2.03 1.80 1.95 2.00 2.05 2.05 2.12 2.12 2.15
22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 30 30 40 35 35
390
2.08 2.14 2.23 2.30 2.12 2.26 2.28 2.03 2.09
25.4 45 30 35 35 30 25.4 50 30 40 35 30 30 45 35 35
470
2.55 2.53 2.55 2.46 2.51 2.51 2.68 2.68
25.4 50 30 40 35 35 30 45 35 35 35 40
560
2.46 2.73 2.75 2.85 2.85 2.88
30 45 35 35 30 50 35 40 35 50
680
3.15 3.15 3.01 3.01 3.44
LARGE TYPES

820
35 45
1000
3.65
193
Upgrade
Wide Temperature Range, Standard

HE Series Solvent Proof
WV 100V
Wide temperature range of -40(-25) ~ +105 C

Standard snap-in terminal type
WV 6.3, 10 16 25, 35 50, 63 80, 100 160~400 450, 500
(at 120Hz, 20 C)
tan 0.50 0.40 0.35 0.25 0.20 0.15 0.20

DRAWING Unit : mm
D 40
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1

D 35, 40
PC Board
Mounting Holes
Insulating sleeve
Blank Blank
4 2 0.1
D 1 max.
30 30 30
22.5
Safety vent L 2 max. 6.0 1

22.5 0.2

Frequency(Hz)
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 250 0.85 1.00 1.20 1.25 1.45
315 ~ 0.85 1.00 1.15 1.20 1.40
194
HE series

WV 6.3 10 16
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
22 25
8200
2.14
22 25 22 30 25.4 25
10000
2.17 2.48 2.56
22 25 22 30 22 35 25.4 30 30 25
12000
2.19 2.48 2.80 2.90 2.97
22 30 22 35 25.4 25 22 40 25.4 35 30 30
15000
2.53 2.83 2.75 3.17 3.29 3.38
22 35 25.4 25 22 35 25.4 30 22 45 25.4 40 30 30
18000
2.85 2.77 3.00 3.11 3.50 3.65 3.57
22 35 25.4 30 22 40 25.4 35 30 25 25.4 45 30 35
22000
3.04 3.15 3.35 3.48 3.38 4.03 3.98
22 40 25.4 35 30 25 22 50 25.4 40 30 30 25.4 50 30 40 35 30
27000
3.40 3.53 3.42 3.88 3.87 3.79 4.42 4.39 4.29
22 50 25.4 40 30 30 25.4 45 30 35 30 45 35 35
33000
3.92 3.91 3.83 4.26 4.20 4.79 4.71
25.4 45 30 35 25.4 50 30 40 35 30 30 50 35 40
39000
4.26 4.20 4.60 4.57 4.46 5.16 5.10
25.4 50 30 40 35 30 30 45 35 35 35 45 40 40
47000
4.63 4.60 4.50 4.95 4.87 5.50 5.60
30 50 35 40 35 45 40 40 40 50
56000
5.17 5.12 5.49 5.59 6.22
35 45 40 40 40 50 40 60
68000
5.52 5.62 6.22 6.83
WV 25 35 50
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
2700
22 30
1.94
3300
22 25 22 35
1.62 2.20
3900
22 30 22 40 25.4 35 30 25
1.88 2.52 2.62 2.54
4700
22 25 22 35 25.4 25 22 45 25.4 40 30 30
1.73 2.14 2.09 2.81 2.93 2.87
5600
22 30 22 35 25.4 30 30 25 22 50 25.4 40 30 35
1.98 2.29 2.37 2.43 3.11 3.11 3.21
6800
22 30 22 40 25.4 35 30 30 25.4 50 30 40 35 30
2.14 2.61 2.71 2.79 3.64 3.61 3.53
8200
22 35 25.4 30 22 50 25.4 40 30 30 30 45 35 35
2.42 2.50 3.02 3.02 2.95 3.94 3.87
10000
22 40 25.4 35 25.4 45 30 35 30 50 35 40
2.77 2.88 3.43 3.38 4.42 4.37
12000
22 45 25.4 40 30 30 25.4 50 30 40 35 30 35 45
3.09 3.22 3.15 3.78 3.75 3.67 4.78
15000
25.4 45 30 35 35 30 30 45 35 35 35 50 40 40
3.62 3.57 3.65 4.19 4.12 5.24 5.13
18000
25.4 50 30 40 35 35 35 40 40 50
3.98 3.95 4.06 4.52 5.76
22000
30 45 35 35 35 45 40 40 40 50
4.36 4.28 4.95 5.04 5.98
27000
35 45 40 40 40 50 40 60
4.92 5.01 5.92 6.61
WV 63 80 100
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
820
22 25 22 30 25.4 25
1.37 1.46 1.51
1000
22 30 25.4 25 22 35 25.4 30
1.62 1.67 1.71 1.77
1200
22 25 22 30 25.4 25 22 40 25.4 35 30 25
1.37 1.67 1.72 1.86 1.94 1.88
1500
22 30 25.4 25 22 35 25.4 30 22 45 25.4 40 30 30
1.50 1.54 1.98 2.05 2.18 2.28 2.23
1800
22 30 25.4 25 22 40 25.4 35 30 25 25.4 45 30 35
1.64 1.69 2.28 2.37 2.30 2.61 2.57
2200
22 35 25.4 30 22 45 25.4 35 30 30 25.4 50 30 40 35 30
1.86 1.92 2.51 2.49 2.56 2.85 2.83 2.76
2700
22 40 25.4 30 30 25 25.4 45 30 35 30 45 35 35
2.17 2.13 2.18 3.03 2.99 3.27 3.22
LARGE TYPES
3300
22 50 25.4 40 30 30 25.4 50 30 40 35 30 30 50 35 40
2.53 2.53 2.48 3.33 3.30 3.23 3.59 3.55
3900
25.4 45 30 35 30 45 35 35 35 45
2.88 2.84 3.75 3.69 4.03
4700
25.4 50 30 40 35 30 30 50 35 40 35 50 40 40
3.20 3.17 3.10 4.10 4.06 4.40 4.31
5600
30 45 35 35 35 45 40 50
3.51 3.46 4.44 4.88
6800
30 50 35 40 35 50 40 40 40 50
3.92 3.88 4.90 4.80 5.18
8200
10000
35 50 40 40
4.74 4.64
195
HE series

WV 160 200 250
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
150
22 20 22 20 25.4 20
0.63 0.68 0.69
180
22 20 22 20 22 25 25.4 20 30 20
0.69 0.69 0.74 0.76 0.83
220
22 20 22 25 25.4 20 22 25 25.4 25 30 20
0.76 0.82 0.84 0.88 0.90 0.92
270
22 25 25.4 20 22 25 25.4 25 30 20 22 30 25.4 25 30 25
0.91 0.93 0.91 1.00 1.02 1.03 1.06 1.09
330
22 25 25.4 25 30 20 22 30 25.4 25 30 20 22 35 25.4 30 30 25
1.01 1.10 1.13 1.07 1.11 1.13 1.20 1.18 1.21
390
22 30 25.4 25 30 20 22 30 25.4 30 30 25 22 40 25.4 35 30 25 35 25
1.17 1.20 1.23 1.24 1.28 1.31 1.36 1.42 1.39 1.42
470
22 30 25.4 25 30 25 22 35 25.4 30 30 25 35 25 22 45 25.4 35 30 30 35 25
1.36 1.32 1.44 1.43 1.48 1.44 1.56 1.56 1.56 1.53 1.56
560
22 35 25.4 30 30 25 35 25 22 45 25.4 35 30 30 35 25 25.4 40 30 30 35 30
1.56 1.53 1.57 1.70 1.63 1.62 1.67 1.70 1.86 1.76 1.80
680
22 40 25.4 35 30 25 35 25 22 50 25.4 40 30 30 35 25 30 35 35 35
1.80 1.79 1.73 1.88 1.88 1.96 1.84 1.88 2.12 2.09
820
25.4 40 30 30 35 25 25.4 45 30 35 35 30 30 40 35 35
2.06 2.02 2.06 2.25 2.13 2.18 2.23 2.40
1000
25.4 40 30 35 35 30 30 40 35 35 35 40 40 40
2.38 2.35 2.41 2.57 2.53 2.76 2.81
1200
25.4 50 30 40 35 30 30 50 35 35 40 40 35 45 40 50
2.52 2.50 2.44 2.72 2.57 2.85 2.91 3.08
1500
35 40 40 40 35 45 40 50 40 60
3.00 3.19 3.13 3.44 3.68
WV 315 350 400
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
56
22 20
0.37
68
22 20 22 20 25.4 20
0.41 0.44 0.45
82
22 20 22 25 25.4 20 22 25 25.4 25 30 20
0.45 0.48 0.49 0.48 0.53 0.54
100
22 25 25.4 20 22 25 25.4 25 30 20 22 25 25.4 25 30 20
0.53 0.55 0.53 0.59 0.60 0.56 0.58 0.60
120
22 30 25.4 25 30 20 22 30 25.4 25 30 20 22 30 25.4 30 30 25
0.62 0.64 0.65 0.62 0.64 0.65 0.66 0.68 0.70
150
22 30 25.4 25 30 20 22 35 25.4 30 30 25 22 35 25.4 30 30 25
0.74 0.76 0.73 0.78 0.76 0.78 0.77 0.75 0.78
180
22 35 25.4 30 30 25 22 40 25.4 35 30 30 22 40 25.4 40 30 30 35 25
0.85 0.88 0.86 0.89 0.88 0.91 0.89 0.93 0.91 0.93
220
22 40 25.4 35 30 25 22 50 25.4 40 30 30 35 25 22 45 25.4 40 30 30 35 30
0.98 0.98 0.98 1.03 1.03 1.00 1.03 1.02 1.01 1.00 1.08
270
25.4 40 30 30 35 25 25.4 45 30 35 35 30 25.4 45 30 35 35 30
1.19 1.12 1.14 1.19 1.17 1.20 1.17 1.17 1.20
330
25.4 40 30 35 35 30 25.4 50 30 40 35 30 25.4 50 30 40 35 35
1.24 1.36 1.33 1.35 1.36 1.36 1.35 1.36 1.40
390
30 35 35 30 25.4 50 30 40 35 35 25.4 60 30 50 35 40
1.47 1.52 1.47 1.54 1.54 1.54 1.61 1.59
470
30 40 35 35 35 40 30 50 35 40 40 40
1.70 1.74 1.74 1.76 1.82 1.85
560
30 45 35 40 35 45 40 40 35 45 40 50
1.90 1.90 2.06 2.02 2.06 2.18
680
30 50 35 45 40 40 40 50 35 50 40 60
2.12 2.18 2.23 2.40 2.27 2.57
WV 450 500
D
F 22 25.4 30 35 40 22 25.4 30 35 40
22 20 22 25 25.4 20
47
0.34 0.27 0.27
22 25 25.4 20 22 30 25.4 25 30 20
56
0.40 0.41 0.31 0.32 0.33
22 25 25.4 25 30 20 22 30 25.4 25 30 25
68
0.44 0.48 0.49 0.34 0.35 0.39
22 30 25.4 25 30 20 22 35 25.4 30 30 25
82
0.51 0.52 0.54 0.40 0.41 0.43
22 30 25.4 25 30 25 22 35 25.4 35 30 25 35 25
100
0.56 0.58 0.64 0.46 0.48 0.47 0.51
22 35 25.4 30 30 25 35 20 22 40 25.4 35 30 30 35 30
120
0.66 0.67 0.70 0.76 0.53 0.55 0.55 0.59
22 45 25.4 30 30 25 35 25 25.4 40 30 30 35 30
150
0.80 0.77 0.83 0.85 0.65 0.64 0.66
25.4 35 30 30 35 25 25.4 45 30 40 35 35
180
0.93 0.90 0.98 0.70 0.74 0.76
25.4 40 30 30 35 30 30 40 35 35
220
1.08 1.06 1.08 0.85 0.88
30 35 35 30 30 50 35 40 40 40
270
1.23 1.26 0.98 1.01 1.03
30 40 35 35 35 50 40 50
330
1.42 1.46 1.17 1.23
30 50 35 40 35 50 40 50
390
1.60 1.66 1.27 1.34
35 40 40 40 40 60
470
1.81 1.85 1.57
560
196
Upgrade
Miniaturized
HK Series Solvent Proof
WV 100V
Miniaturized
Smaller case sizes than HE series

WV 6.3, 10 16 25, 35 50, 63 80, 100 160~400 450, 500
(at 120Hz, 20 C)
tan 0.50 0.40 0.35 0.25 0.20 0.15 0.20

DRAWING Unit : mm
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1

Terminal length of height 20mm products is applied shorter terminal to standard terminal type. LARGE TYPES

Frequency
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 250 0.85 1.00 1.20 1.25 1.45
350 ~ 0.85 1.00 1.15 1.20 1.40
197
HK series

WV 6.3 10 16
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
22 25
8200
2.14
22 25 22 30 25.4 25
10000
2.17 2.48 2.56
22 25 22 30 22 35 25.4 30 30 25
12000
2.19 2.48 2.80 2.90 2.97
22 30 22 35 25.4 25 22 40 25.4 35 30 30
15000
2.53 2.83 2.75 3.17 3.29 3.38
22 35 25.4 25 22 35 25.4 30 22 45 25.4 40 30 30
18000
2.85 2.77 3.00 3.11 3.50 3.65 3.57
22 35 25.4 30 22 40 25.4 35 30 25 25.4 45 30 35
22000
3.04 3.15 3.35 3.48 3.38 4.03 3.98
22 40 25.4 35 30 25 22 50 25.4 40 30 30 25.4 50 30 40 35 30
27000
3.40 3.53 3.42 3.88 3.87 3.79 4.42 4.39 4.29
22 50 25.4 40 30 30 25.4 45 30 35 30 45 35 35
33000
3.92 3.91 3.83 4.26 4.20 4.79 4.71
25.4 45 30 35 25.4 50 30 40 35 30 30 50 35 40
39000
4.26 4.20 4.60 4.57 4.46 5.16 5.10
25.4 50 30 40 35 30 30 45 35 35 35 45 40 40
47000
4.63 4.60 4.50 4.95 4.87 5.50 5.60
30 50 35 40 35 45 40 40 40 50
56000
5.17 5.12 5.49 5.59 6.22
35 45 40 40 40 50 40 60
68000
5.52 5.62 6.22 6.83
WV 25 35 50
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
2700
22 30
1.94
3300
22 25 22 35
1.62 2.20
3900
22 30 22 40 25.4 35 30 25
1.88 2.52 2.62 2.54
4700
22 25 22 35 25.4 25 22 45 25.4 40 30 30
1.73 2.14 2.09 2.81 2.93 2.87
5600
22 30 22 35 25.4 30 30 25 22 50 25.4 40 30 35
1.98 2.29 2.37 2.43 3.11 3.11 3.21
6800
22 30 22 40 25.4 35 30 30 25.4 50 30 40 35 30
2.14 2.61 2.71 2.79 3.64 3.61 3.53
8200
22 35 25.4 30 22 50 25.4 40 30 30 30 45 35 35
2.42 2.50 3.02 3.02 2.95 3.94 3.87
10000
22 40 25.4 35 25.4 45 30 35 30 50 35 40
2.77 2.88 3.43 3.38 4.42 4.37
12000
22 45 25.4 40 30 30 25.4 50 30 40 35 30 35 45
3.09 3.22 3.15 3.78 3.75 3.67 4.78
15000
25.4 45 30 35 35 30 30 45 35 35 35 50 40 40
3.62 3.57 3.65 4.19 4.12 5.24 5.13
18000
25.4 50 30 40 35 35 35 40 40 50
3.98 3.95 4.06 4.52 5.76
22000
30 45 35 35 35 45 40 40 40 50
4.36 4.28 4.95 5.04 5.98
27000
35 45 40 40 40 50 40 60
4.92 5.01 5.92 6.61
WV 63 80 100
D
F 22 25.4 30 35 40 22 25.4 30 35 40 22 25.4 30 35 40
820
22 25 22 30 25.4 25
1.37 1.46 1.51
1000
22 30 25.4 25 22 35 25.4 30
1.62 1.67 1.71 1.77
1200
22 25 22 30 25.4 25 22 40 25.4 35 30 25
1.37 1.67 1.72 1.86 1.94 1.88
1500
22 30 25.4 25 22 35 25.4 30 22 45 25.4 40 30 30
1.50 1.54 1.98 2.05 2.18 2.28 2.23
1800
22 30 25.4 25 22 40 25.4 35 30 25 25.4 45 30 35
1.64 1.69 2.28 2.37 2.30 2.61 2.57
2200
22 35 25.4 30 22 45 25.4 35 30 30 25.4 50 30 40 35 30
1.86 1.92 2.51 2.49 2.56 2.85 2.83 2.76
2700
22 40 25.4 30 30 25 25.4 45 30 35 30 45 35 35
2.17 2.13 2.18 3.03 2.99 3.27 3.22
3300
22 50 25.4 40 30 30 25.4 50 30 40 35 30 30 50 35 40
2.53 2.53 2.48 3.33 3.30 3.23 3.59 3.55
3900
25.4 45 30 35 30 45 35 35 35 45
2.88 2.84 3.75 3.69 4.03
4700
25.4 50 30 40 35 30 30 50 35 40 35 50 40 40
3.20 3.17 3.10 4.10 4.06 4.40 4.31
5600
30 45 35 35 35 45 40 50
3.51 3.46 4.44 4.88
6800
30 50 35 40 35 50 40 40 40 50
3.92 3.88 4.90 4.80 5.18
8200
10000
35 50 40 40
4.74 4.64
198
HK series
WV 160 200 250
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
120
22 20
0.56
150
22 20 22 20
0.63 0.68
180
22 20 25.4 20 22 25 25.4 20
0.69 0.76 0.74 0.76
220
22 20 22 25 25.4 20 22 25 25.4 25 30 20
0.76 0.82 0.84 0.82 0.90 0.92
270
22 25 25.4 20 22 25 25.4 25 30 20 22 30 25.4 25 30 20
0.91 0.93 0.91 1.00 1.02 0.97 1.00 1.02
330
22 25 25.4 20 22 30 25.4 25 30 20 22 35 25.4 30 30 25
1.01 1.03 1.07 1.11 1.13 1.14 1.18 1.21
390
22 25 25.4 25 30 20 22 30 25.4 25 30 25 22 40 25.4 35 30 25 35 25
1.09 1.20 1.23 1.17 1.20 1.31 1.30 1.35 1.31 1.42
470
22 30 25.4 25 30 20 22 35 25.4 30 30 25 35 20 22 45 25.4 35 30 30 35 25
1.28 1.32 1.35 1.36 1.40 1.44 1.47 1.50 1.48 1.53 1.56
560
22 35 25.4 30 30 25 22 40 25.4 30 30 25 35 25 22 50 25.4 40 30 30 35 25
1.48 1.53 1.57 1.56 1.53 1.57 1.70 1.71 1.70 1.67 1.70
680
22 40 25.4 30 30 25 35 20 22 45 25.4 35 30 30 35 25 25.4 50 30 35 35 30
1.72 1.69 1.73 1.76 1.80 1.79 1.84 1.88 2.05 1.94 1.98
820
22 45 25.4 35 30 30 35 25 25.4 45 30 30 35 25 30 40 35 35
1.98 1.96 2.02 2.06 2.16 2.02 2.06 2.23 2.29
1000
22 50 25.4 40 30 30 35 25 25.4 50 30 35 35 30 30 50 35 40
2.28 2.28 2.23 2.28 2.48 2.35 2.41 2.68 2.65
1200
25.4 45 30 35 35 30 30 40 35 35 30 60 35 45
2.41 2.38 2.44 2.50 2.57 2.92 2.80
1500
25.4 50 30 40 35 30 30 50 35 40 35 50
2.81 2.79 2.73 3.04 3.00 3.25
1800
30 45 35 35 35 45
3.19 3.14 3.43
2200
30 50 35 45 35 50
3.44 3.55 3.68
2700
35 50
4.08
WV 350 400 450
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
47
22 20
0.34
56
22 20 22 20 22 25
0.37 0.37 0.40
68
22 20 25.4 20 22 20 25.4 20 22 30 25.4 20
0.41 0.45 0.44 0.45 0.47 0.48
82
22 25 25.4 20 22 25 25.4 20 22 30 25.4 25
0.48 0.49 0.48 0.53 0.51 0.53
100
22 25 25.4 25 30 20 22 30 25.4 25 30 20 22 35 25.4 30 30 25
0.53 0.58 0.60 0.57 0.58 0.60 0.60 0.62 0.64
120
22 30 25.4 25 30 20 22 30 25.4 25 30 25 22 40 25.4 30 30 25
0.62 0.64 0.65 0.66 0.64 0.70 0.69 0.68 0.70
150
22 35 25.4 30 30 25 22 35 25.4 30 30 25 35 20 22 45 25.4 35 30 25 35 25
0.74 0.76 0.78 0.78 0.76 0.78 0.80 0.81 0.85 0.83 0.85
25.4 30
180 22 40 25.4 30 30 25 35 20 22 40 25.4 35 30 30 35 25 22 50 0.83 30 30 35 25
0.85 0.83 0.86 0.87 0.89 0.88 0.91 0.93 0.93 25.4 35 0.91 0.93
0.93
220
22 45 25.4 30 30 30 35 25 22 50 25.4 40 30 30 35 25 25.4 40 30 35 35 25
0.98 0.98 1.00 1.03 1.03 1.03 1.00 1.03 1.07 1.06 1.03
270
22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 30 30 35 35 30
1.14 1.14 1.11 1.14 1.19 1.17 1.20 1.23 1.20
330
25.4 45 30 35 35 30 25.4 50 30 40 35 30 30 40 35 35
1.31 1.30 1.33 1.37 1.36 1.33 1.42 1.40
390
25.4 45 30 40 35 35 30 45 35 35 30 45 35 40
1.49 1.48 1.52 1.54 1.52 1.61 1.59
470
30 45 35 35 30 50 35 40 35 45
1.69 1.67 1.76 1.74 1.82
560
30 50 35 40 35 45 35 50
1.92 1.90 1.98 2.06
680
35 45 35 50
2.27 2.27
WV 500
D
F 22 25.4 30 35 40
22 35 25.4 30
82
0.42 0.43
22 40 25.4 35 30 25
100
0.49 0.48 0.50
LARGE TYPES
22 45 25.4 35 30 30 35 25
120
0.51 0.50 0.50 0.51
25.4 40 30 35 35 30
150
0.53 0.53 0.54
25.4 45 30 40 35 35
180
0.74 0.74 0.76
30 50 35 35
220
0.89 0.84
30 50 35 40
270
1.02 0.97
30 55 35 50
330
1.17 1.17
35 60
390
1.36
35 60 40 60
470
1.53 1.57
560
1.82 Ripple current (Arms) at 105 C, 120Hz 199
High Ripple
HG Series
High ripple current compared with HK series

WV 250 400 450
(at 120Hz, 20 C)
tan 0.15 0.15 0.20

DRAWING Unit : mm
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 3.0 max. 6.0 1 4.0 0.5
1.5 0.1


WV 250 400 450
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 35 25 30
150
1.10 1.10
22 20 25 20 22 35 25 25 30 20 22 40 25 35 30 25 35 25
180
0.88 0.89 1.26 1.25 1.29 1.32 1.32 1.29 1.32
22 25 25 20 22 40 25 30 30 25 25 35 30 30 35 25
220
0.93 1.06 1.46 1.47 1.43 1.52 1.50 1.46
22 30 25 25 30 20 25 40 30 30 35 25 30 35 35 30
330
1.35 1.39 1.43 1.95 1.93 1.89 2.03 2.20
22 40 25 30 30 25 30 40 35 30 35 40
470
1.78 1.74 1.80 2.20 2.48 2.59
22 45 25 35 30 25 35 25 35 35 35 45
560
2.02 2.01 1.98 2.01 2.82 2.93
25 40 30 30 35 25 Case size D L (mm) 35 40 35 50
680
2.43 2.29 2.34 3.24 3.43
Ripple current (Arms) at 105 C, 120Hz

Frequency
WV
250 0.85 1.00 1.20 1.25 1.45

400, 450 0.85 1.00 1.15 1.20 1.40
200
Upgrade
Long Life
HL Series Solvent Proof
WV 100V
Long Life
Long life than HK series

WV 10 16 25, 35 50, 63 80, 100 160 ~ 400 450
(at 120Hz, 20 C)
tan 0.50 0.40 0.35 0.25 0.20 0.15 0.20

DRAWING Unit : mm
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1

LARGE TYPES

Frequency(Hz)
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 250 0.85 1.00 1.20 1.25 1.45
350 ~ 0.85 1.00 1.15 1.20 1.40
201
HL series
WV 10 16 25
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
5600
22 25
1.50
6800
22 30 25.4 25
1.90 1.90
8200
22 25 22 35 25.4 30 30 25
1.80 2.10 2.10 2.10
10000
22 30 25.4 25 22 40 25.4 35 30 25
2.20 2.20 2.30 2.30 2.20
12000
22 30 22 35 25.4 30 22 40 25.4 35 30 30
2.10 2.40 2.40 2.50 2.50 2.60
15000
22 30 25.4 25 22 40 25.4 35 30 30 25.4 40 30 35 35 30
2.30 2.30 2.70 2.70 2.70 2.80 2.90 2.90
18000
22 35 25.4 30 22 45 25.4 40 30 30 35 25 25.4 50 30 40 35 30
2.70 2.70 2.80 3.00 3.00 3.00 3.10 3.10 3.10
22000
22 40 25.4 35 30 30 25.4 40 30 35 35 30 30 45 35 35
2.90 2.90 2.90 3.10 3.30 3.30 3.50 3.50
27000
22 45 25.4 40 30 30 35 25 30 40 35 30 30 50 35 40
3.30 3.30 3.30 3.30 3.60 3.60 3.80 3.70
33000
25.4 45 30 35 35 30 30 45 35 35 35 45
3.50 3.50 3.50 4.00 4.00 4.10
39000
30 40 35 30 30 50 35 40 35 50
3.80 3.70 4.30 4.30 4.40
47000
30 45 35 35 35 45
4.00 3.90 4.60
56000
35 40
4.50
WV 35 50 63
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
1200
22 25
1.30
1500
22 30 25.4 25
1.50 1.50
1800
22 25 22 35 25.4 30 30 25
1.30 1.60 1.60 1.60
2200
22 30 22 40 25.4 30 30 30
1.40 1.80 1.80 1.80
2700
22 30 25.4 25 22 45 25.4 35 30 30
1.60 1.60 2.00 2.00 2.00
3300
22 25 22 35 25.4 30 22 50 25.4 40 30 35 35 25
1.50 1.80 1.80 2.20 2.20 2.20 2.20
3900
22 30 22 40 25.4 30 30 25 25.4 45 30 35 35 30
1.60 1.90 1.90 1.90 2.40 2.40 2.40
4700
22 35 25.4 25 22 40 25.4 35 30 30 35 25 25.4 50 30 40 35 35
1.80 1.80 2.00 2.10 2.10 2.10 2.60 2.60 2.60
5600
22 35 25.4 30 22 45 25.4 40 30 35 35 25 30 45 35 35
2.00 2.00 2.20 2.30 2.30 2.30 2.80 2.80
6800
22 40 25.4 35 30 25 22 50 25.4 45 30 35 35 30 35 40
2.20 2.20 2.20 2.40 2.50 2.50 2.50 3.10
8200
22 45 25.4 35 30 30 35 25 30 40 35 30 35 45
2.30 2.30 2.40 2.40 2.80 2.70 3.40
10000
25.4 40 30 35 35 25 30 45 35 35 35 50
2.50 2.60 2.50 3.00 3.00 3.80
12000
25.4 45 30 35 35 30 35 40
2.80 2.80 2.90 3.30
15000
30 40 35 35 35 45
3.10 3.20 3.70
18000
30 45 35 40
3.30 3.50
22000
35 45
3.70
WV 80 100
D
F 22 25.4 30 35 22 25.4 30 35
22 25
680
1.10
22 25 22 30 25.4 25
820
1.20 1.30 1.30
22 30 25.4 25 22 35 25.4 30
1000
1.30 1.30 1.50 1.50
22 35 25.4 25 22 40 25.4 35 30 25
1200
1.50 1.50 1.60 1.60 1.60
22 40 25.4 30 30 25 22 45 25.4 40 30 30
1500
1.60 1.60 1.60 1.80 1.80 1.80
22 45 25.4 35 30 30 25.4 45 30 35 35 25
1800
1.80 1.80 1.80 2.00 2.00 2.00
22 50 25.4 40 30 30 35 25 25.4 50 30 40 35 30
2200
2.00 2.00 2.00 2.00 2.20 2.20 2.20
25.4 45 30 35 35 30 30 45 35 35
2700
2.20 2.20 2.20 2.40 2.40
30 40 35 35 35 40
3300
2.40 2.40 2.70
30 45 35 40 35 45
3900
2.60 2.60 2.90
35 45
4700
3.00
5600
3.30 Ripple current (Arms) at 105 C, 120Hz
202
HL series

WV 160 200 250
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 20
120
0.56
22 20 22 25 25.4 20
150
0.63 0.68 0.69
22 20 25.4 20 22 25 25.4 20
180
0.69 0.76 0.74 0.76
22 20 22 25 25.4 20 22 25 25.4 25 30 20
220
0.76 0.82 0.84 0.82 0.90 0.92
22 25 25.4 20 22 25 25.4 25 30 20 22 30 25.4 25 30 20
270
0.91 0.93 0.91 1.00 1.02 0.97 1.00 1.02
22 25 25.4 20 22 30 25.4 25 30 20 22 35 25.4 30 30 25
330
1.01 1.03 1.07 1.11 1.13 1.14 1.18 1.21
22 25 25.4 25 30 20 22 30 25.4 25 30 25 22 40 25.4 35 30 25 35 25
390
1.09 1.20 1.23 1.17 1.20 1.31 1.30 1.35 1.31 1.42
22 30 25.4 25 30 20 22 35 25.4 30 30 25 22 45 25.4 35 30 30 35 25
470
1.28 1.32 1.35 1.36 1.40 1.44 1.50 1.48 1.53 1.56
22 35 25.4 30 30 25 22 40 25.4 30 30 25 35 25 22 50 25.4 40 30 30 35 25
560
1.48 1.53 1.57 1.56 1.53 1.57 1.70 1.71 1.70 1.67 1.70
22 40 25.4 30 30 25 22 45 25.4 35 30 30 35 25 25.4 50 30 35 35 30
680
1.72 1.69 1.73 1.80 1.79 1.84 1.88 2.05 1.94 1.98
22 45 25.4 35 30 30 35 25 25.4 45 30 30 35 25 30 40 35 35
820
1.98 1.96 2.02 2.06 2.16 2.02 2.06 2.23 2.29
22 50 25.4 40 30 30 35 25 25.4 50 30 35 35 30 30 50 35 40
1000
2.28 2.28 2.23 2.28 2.48 2.35 2.41 2.68 2.65
25.4 45 30 35 35 30 30 40 35 35 35 45
1200
2.41 2.38 2.44 2.50 2.57 2.80
25.4 50 30 40 35 35 30 50 35 40 35 50
1500
2.81 2.79 2.73 3.04 3.00 3.25
WV 350 400 450
D 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35

F
22 20 22 20 25.4 20 22 25
56
0.37 0.40 0.45 0.44
22 20 25.4 20 22 25 25.4 20 22 30 25.4 25
68
0.41 0.45 0.48 0.49 0.51 0.52
22 25 25.4 20 22 25 25.4 25 30 20 22 30 25.4 25
82
0.48 0.49 0.52 0.58 0.59 0.56 0.58
22 25 25.4 25 30 20 22 30 25.4 25 30 20 22 35 25.4 30 30 25
100
0.53 0.58 0.60 0.62 0.63 0.66 0.66 0.68 0.70
22 30 25.4 25 30 20 22 35 25.4 25 30 25 22 40 25.4 30 30 25 35 25
120
0.62 0.64 0.65 0.72 0.70 0.77 0.75 0.74 0.77 0.83
22 35 25.4 30 30 25 22 40 25.4 30 30 25 22 45 25.4 40 30 30 35 25
150
0.74 0.76 0.78 0.85 0.83 0.85 0.89 0.93 0.91 0.93
22 40 25.4 30 30 25 22 45 25.4 35 30 30 35 25 22 50 25.4 40 30 30 35 25
180
0.85 0.83 0.86 0.97 0.96 1.00 1.02 1.02 1.02 1.00 1.02
22 45 25.4 35 30 30 35 25 22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 25
220
0.98 0.98 1.00 1.03 1.13 1.13 1.10 1.13 1.17 1.16 1.13
22 50 25.4 40 30 30 35 25 25.4 45 30 35 35 30 30 40 35 30
270
1.14 1.14 1.11 1.14 1.30 1.28 1.32 1.35 1.30
25.4 45 30 35 35 30 25.4 50 30 40 35 30 30 45 35 35
330
1.31 1.30 1.33 1.50 1.49 1.46 1.56 1.50
25.4 50 30 40 35 35 30 45 35 35 30 50 35 40
390
1.49 1.48 1.52 1.69 1.67 1.77 1.74
30 45 35 35 30 50 35 40 Case size D L (mm)
470
1.69 1.67 1.93 1.91
30 50 35 40
560
LARGE TYPES
203
Upgrade
Snap-in Terminal Type, Long Life

HY Series Long Life

Voltage range of 160 ~ 450V
Suited for use in industrial power supplies where high reliability
Operating temperature range WV< 350: -40 ~ +105 C, WV 350: -25 ~ +105 C
WV 160 200 250 350 400 450
(at 120Hz, 20 C)
tan 0.15 0.15 0.15 0.15 0.15 0.20

Unit : mm
DRAWING
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0. 1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1


Frequency
WV
160 ~ 250 0.85 1.00 1.20 1.25 1.45
350 ~ 0.85 1.00 1.15 1.20 1.40
204
HY series

WV 160 200 250
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 25 22 30 25.4 25 22 35 25.4 30 30 25
270
0.91 1.05 1.05 1.02 1.06 1.09
22 25 22 30 25.4 25 22 40 25.4 35 30 25
330
1.11 1.16 1.16 1.19 1.24 1.20
22 30 25.4 25 22 35 25.4 30 30 25 22 45 25.4 35 30 30
390
1.26 1.35 1.29 1.29 1.31 1.36 1.35 1.39
22 30 25.4 30 22 40 25.4 35 30 30 25.4 45 30 35 35 30
470
1.39 1.40 1.42 1.48 1.52 1.63 1.61 1.64
22 40 25.4 30 30 25 22 45 25.4 35 30 30 25.4 50 30 35 35 30
560
1.55 1.55 1.57 1.63 1.62 1.67 1.85 1.75 1.80
22 45 25.4 35 30 30 25.4 40 30 35 30 45 35 35
680
1.80 1.78 1.93 1.87 1.93 2.12 2.08
25.4 40 30 30 25.4 50 30 40 35 30 30 50 35 40
820
2.06 2.01 2.24 2.23 2.17 2.42 2.39
25.4 45 30 35 30 45 35 35 35 45
1000
2.38 2.34 2.57 2.52 2.76
25.4 50 30 40 35 35 30 50 35 40 35 50
1200
2.54 2.56 2.56 2.71 2.68 2.90
30 45 35 35 35 50
1500
2.96 2.89 3.25
30 50 35 40
1800
3.32 3.30
WV 350 400 450
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 25
47
0.46
22 20 22 30 25.4 20
56
0.48 0.52 0.52
22 25 25.4 20 22 30 25.4 25
68
0.55 0.55 0.58 0.58
22 25 22 30 25.4 25 22 35 25.4 30 30 20
82
0.58 0.63 0.63 0.65 0.65 0.65
22 25 25.4 25 22 30 25.4 25 22 40 25.4 30 30 25
100
0.67 0.67 0.70 0.70 0.74 0.72 0.73
22 30 25.4 25 22 35 25.4 30 30 25 25.4 35 30 30
120
0.77 0.76 0.79 0.79 0.79 0.82 0.82
22 35 25.4 30 22 40 25.4 30 30 25 25.4 40 30 35 35 25
150
0.88 0.88 0.90 0.88 0.90 0.94 0.96 0.94
22 40 25.4 30 25.4 35 30 30 35 25 30 35 35 30
180
0.99 0.96 1.01 1.01 1.01 1.05 1.07
22 45 25.4 35 30 30 25.4 40 30 35 35 25 30 40 35 35
220
1.12 1.11 1.11 1.14 1.16 1.14 1.20 1.21
25.4 40 30 35 35 25 30 40 35 30 35 40
270
1.26 1.28 1.26 1.33 1.31 1.40
30 35 35 30 30 45 35 35 35 45
330
1.42 1.45 1.52 1.48 1.60
30 40 35 35 35 40 35 50
390
1.60 1.61 1.68 1.79
35 40 35 45
470
1.85 1.91
560
2.06 2.14 Ripple current (A rms) at 105 C, 120Hz
LARGE TYPES
205
New
Snap-in Terminal Type, Long Life

JY Series Long Life

Voltage range of 400 ~ 450V
Suited for use in industrial power supplies where high reliability

WV 400 450
(at 120Hz, 20 C)
tan 0.15 0.20

Unit : mm
DRAWING
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1


Frequency
WV
Coefficient 0.85 1.00 1.15 1.20 1.40
206
JY series

WV 400 450
D
F 22 25.4 30 35 22 25.4 30 35
22 25
47
0.38
22 20 22 30 25.4 20
56
0.39 0.45 0.43
22 25 25.4 20 22 30 25.4 25
68
0.46 0.48 0.52 0.51
22 30 25.4 25 22 35 25.4 30 30 20
82
0.54 0.53 0.60 0.59 0.57
22 30 25.4 25 22 40 25.4 30 30 25
100
0.60 0.62 0.69 0.69 0.67
22 35 25.4 30 30 25 25.4 35 30 30
120
0.69 0.72 0.69 0.79 0.74
22 40 25.4 30 30 25 25.4 40 30 35 35 25
150
0.84 0.84 0.82 0.92 0.91 0.89
25.4 35 30 30 35 25 30 35 35 30
180
0.97 0.95 0.92 1.04 1.03
25.4 40 30 35 35 25 30 40 35 35
220
1.11 1.11 1.08 1.20 1.19
30 40 35 30 35 40
270
1.28 1.26 1.37
30 45 35 35 35 45
330
1.47 1.46 1.58
35 40
390
1.65
470
LARGE TYPES
207
HB High Temperature Range, For 125 C Use

WV 100V

With a guaranteed useful life of 10 years at 60 C
Ideal for industrial applications requiring continuous operation

WV 10 16 25 35 50, 63 80 ~ 160 200, 250
(at 120Hz, 20 C)
tan 0.50 0.40 0.30 0.25 0.20 0.17 0.15


Unit : mm
DRAWING
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1 4.0 0.5
1.5 0.1


Frequency
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 0.85 1.00 1.20 1.25 1.45
208
HB series

WV 10 16 25
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 30
1500
0.95
22 30 22 40 25.4 30
2200
1.00 1.28 1.26
22 30 22 40 25.4 35 22 50 25.4 40 30 30
3300
1.09 1.36 1.41 1.72 1.72 1.68
22 40 25.4 35 22 50 25.4 40 30 30 25.4 50 30 40 35 30
4700
1.45 1.51 1.78 1.77 1.74 2.23 2.22 2.17
22 50 25.4 40 30 35 30 40 35 30 30 50 35 40
6800
1.91 1.91 1.97 2.31 2.26 2.90 2.87
30 45 35 35 35 45
10000
2.62 2.57 3.14
35 45
15000
3.44
WV 35 50 63
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 35 25.4 30
470
0.69 0.71
22 30 22 40 25.4 35 30 30
680
0.78 0.87 0.91 0.93
22 30 22 40 25.4 30 25.4 45 30 35 35 30
1000
0.85 1.06 1.04 1.21 1.19 1.22
22 40 25.4 30 22 50 25.4 40 30 30 30 45 35 40
1500
1.16 1.14 1.42 1.42 1.39 1.60 1.65
22 50 25.4 40 30 30 30 40 35 35 35 50
2200
1.54 1.54 1.50 1.86 1.91 2.16
30 40 35 35 35 40
3300
2.04 2.09 2.45
35 40
4700
2.61
WV 80 100 160
D
F 22 25.4 30 35 22 25.4 30 35 22 25.4 30 35
22 30
150
0.37
22 30 22 40 25.4 30
220
0.48 0.50 0.49
22 30 22 40 25.4 30 22 50 25.4 40 30 30
330
0.59 0.66 0.65 0.67 0.67 0.65
22 40 25.4 35 22 50 25.4 40 30 35 25.4 50 30 40 35 30
470
0.79 0.82 0.86 0.86 0.89 0.87 0.86 0.84
25.4 40 30 35 30 40 35 30 30 50 35 40
680
1.04 1.07 1.12 1.09 1.12 1.11
30 45 35 35 35 40 35 50
1000
1.42 1.40 1.46 1.46
35 45
1500
1.86
WV 200 250
D
F 22 25.4 30 35 22 25.4 30 35
22 30
LARGE TYPES
100
0.32
22 35 22 40 25.4 30
150
0.42 0.44 0.43
22 45 25.4 40 30 30 22 50 25.4 40 30 35 35 30
220
0.56 0.58 0.57 0.58 0.58 0.60 0.61
25.4 50 30 40 35 30 30 45 35 35
330
0.77 0.77 0.75 0.80 0.79
30 50 35 40 35 45 Case size D L (mm)
470
0.99 0.98 1.03 Ripple current (A rms) at 125 C, 120Hz
35 50
680
1.28
209
Lug Terminal Type

LM Series Solvent Proof
WV 100V
Lug terminal series

Suited for use in power supplies and industrial controls
WV 16 25 35~63 80~350 400~450
(at 120Hz, 20 C)
tan 0.35 0.30 0.25 0.20 0.25

DRAWING Unit : mm
Insulating sleeve Terminal Safety vent

max.
D
L max. P 1
Bottom plate
TERMINAL
For solder tag
D 35 40 51 D 25.4 30 35 40 51
P 10 10 14 18 18
1 2
2 3
Dimensions
3
Code LC LA LD

Frequency
WV
~ 100 0.85 1.00 1.06 1.15 1.20

160 ~ 250 0.85 1.00 1.20 1.25 1.45
315 ~ 0.85 1.00 1.15 1.20 1.40
210
LM series

WV
16 25 35 40 50
F
3300 25.4 30 2.46 25.4 30 2.46
4700 25.4 30 2.89 25.4 40 3.21 25.4 40 3.21
6800 25.4 30 3.12 25.4 40 3.73 25.4 50 4.07 25.4 50 4.07
10000 25.4 30 3.42 25.4 40 4.03 25.4 50 4.71 25.4 60 5.07 30 50 5.08
15000 25.4 40 4.41 25.4 50 5.07 30 50 5.81 30 60 6.24 35 60 6.67
22000 25.4 50 5.44 30 50 6.15 35 60 7.44 35 60 7.44 35 80 8.34
33000 30 50 6.57 35 60 7.85 35 80 9.18 35 80 9.18 40 100 10.6
47000 35 60 8.19 35 80 9.49 40 100 11.3 51 105 12.5 51 105 12.5
68000 35 80 9.85 40 100 11.6 51 105 13.2
100000 40 100 12.0 51 105 13.5
150000 51 105 13.9
WV
63 80 100 160 200
F
330 25.4 30 0.92 25.4 30 0.92
470 25.4 40 1.22 25.4 40 1.22
680 25.4 50 1.60 25.4 50 1.60
1000 25.4 30 1.60 25.4 60 2.09 30 50 2.09
1500 25.4 30 1.92 25.4 40 2.13 30 60 2.69 35 60 2.87
2200 25.4 30 2.05 25.4 40 2.52 25.4 50 2.75 35 60 3.40 35 80 3.81
3300 25.4 40 2.73 25.4 50 3.29 30 50 3.55 35 100 5.02 40 100 5.27
4700 25.4 50 3.50 25.4 60 4.14 35 60 4.76 40 100 6.15 51 105 6.80
6800 25.4 60 4.38 30 60 5.15 35 80 6.17 51 105 7.86
10000 30 60 5.46 35 80 7.08 40 100 8.16
15000 35 80 7.48 40 80 8.43 51 105 10.2
22000 35 100 9.16 51 105 11.3
33000 51 105 11.7
WV
250 315 350 400 450
F
68 25.4 30 0.37
100 25.4 30 0.51 25.4 30 0.45 25.4 40 0.50
150 25.4 30 0.62 25.4 40 0.69 25.4 40 0.62 25.4 50 0.67
220 25.4 30 0.75 25.4 40 0.84 25.4 50 0.91 25.4 50 0.81 30 50 0.88
25.4 40 1.02 25.4 50 1.12 25.4 60 1.20 30 60 1.16 35 60 1.24

LARGE TYPES
330
470 25.4 50 1.33 25.4 60 1.43 30 60 1.54 35 60 1.47 35 80 1.65
680 30 50 1.73 30 60 1.86 35 60 1.98 35 80 1.99 35 100 2.18
1000 30 60 2.25 35 70 2.56 35 100 2.96 40 100 2.78 51 80 2.77
1500 35 80 3.22 35 100 3.54 40 100 3.72 51 105 3.69
2200 35 100 4.19 40 100 4.40 51 105 4.86 Ripple current (A rms) at 85 C, 120Hz
3300 51 80 5.24 51 105 5.82 Case size D L (mm)
211
Upgrade
Screw Terminal Type, Standard

GT Series
Ideally suited for use as input and output filter capacitors in

power supplies
Suited for smoothing circuits for general purpose inverters
and control circuits for F.A. machines
Designed for use as input filter capacitor for current U.P.S.
D WV 16 25 35 50 63 80 100 160 ~250 350 ~500
35 0.70 0.45 0.45 0.30 0.25 0.25 0.20 0.15 0.25
51 1.00 0.60 0.60 0.45 0.35 0.30 0.20 0.15 0.25
(at 120Hz, 20 C) 63.5 1.30 0.80 0.70 0.50 0.40 0.35 0.25 0.20 0.25
76.2 2.00 1.60 0.90 0.70 0.50 0.45 0.35 0.25 0.25
89 2.50 2.40 1.00 0.80 0.60 0.50 0.40 0.30 0.25

Load life WV 250 : Within 15% of the initial value
Capacitance change
(after application of the rated WV 350 : Within 20% of the initial value
voltage for 2000 hours at 85 C) WV 250 : Less than 175% of the specified value
tan
WV 350 : Less than 300% of the specified value
DRAWING Unit : mm
Bottom plate Insulating sleeve

D 2 max.
P 1
Safety vent
L 3 max. M5 Hexagon head bolt
6.0 1
TWO LEGS ANGLE THREE LEGS ANGLE
120
T
3.5
U
4.5
B B T
A 1 A 1 U
TWO LEGS ANGLE SIZE TABLE THREE LEGS ANGLE SIZE TABLE
D B A T U P D B A T U P
35 24 29 7 10 30 12.7 51 32.9 38.9 7 12 60 22

51 33.6 39.9 6 14 30 22 63.5 38.4 45.3 7 14 60 28.6
63.5 40.8 46.8 6 14 30 28.6 76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
212
GT series

WV
16 25 35 50
F
10000 35 60 6.2
15000 35 50 5.8 35 80 8.5
22000 35 60 7.5 35 68 7.9 35 100 11.3
33000 35 60 7.4 35 80 10.3 35 100 11.3 35 120 15.0
47000 35 80 9.9 35 100 13.5 35 120 14.6 51 100 15.2
68000 35 100 13.1 51 80 14.5 51 100 15.9 51 120 19.7
100000 51 80 13.7 51 100 19.2 51 120 20.7 63.5 120 24.2
150000 51 100 18.3 51 140 27.1 63.5 120 25.1 76.2 120 25.9
220000 51 140 25.4 63.5 120 28.4 76.2 120 27.7 76.2 160 35.1
330000 63.5 120 27.3 76.2 120 29.3 76.2 160 37.9
470000 76.2 120 27.1 76.2 160 39.2
680000 76.2 160 36.5
WV
63 80 100 160
F
1500 35 60 3.4
2200 35 80 4.6
3300 35 100 6.2
4700 35 60 5.2 51 80 7.7
6800 35 50 5.2 35 60 5.6 35 80 7.0 51 100 10.0
10000 35 60 6.8 35 80 7.6 35 100 9.4 51 140 14.1
15000 35 80 9.3 35 120 11.1 51 80 11.8 63.5 140 16.5
22000 35 120 13.4 51 80 11.7 51 100 15.6 76.2 140 17.6
33000 51 100 14.5 51 120 16.8 51 140 22.0
47000 51 120 18.6 63.5 100 18.5 63.5 140 25.0
68000 63.5 100 20.8 63.5 140 25.4 76.2 140 26.2
100000 76.2 120 25.0 76.2 140 29.7
150000 76.2 140 32.5
WV
200 250
F
330
470
680 35 50 2.1
1000 35 60 2.8 35 68 2.9
1500 35 68 3.6 35 80 3.8
2200 35 100 5.1 35 120 5.5
3300 35 120 6.7 51 100 7.0
4700 51 100 8.3 51 140 9.6
6800 51 140 11.5 63.5 120 10.0
10000 63.5 120 12.1 76.2 120 11.2
15000 76.2 120 13.7 76.2 160 15.3 Ripple current (A rms) at 85 C, 120Hz
22000 76.2 160 18.6 Case size D L (mm)
LARGE TYPES
213
GT series

WV
350 400 450
Item Ripple current Ripple current Ripple current

D L D L D L
(A rms) (A rms) (A rms)
(mm) (mm) (mm)
F 40 C 120Hz 85 C 120Hz 40 C 120Hz 85 C 120Hz 40 C 120Hz 85 C 120Hz
180 35 60 2.9 1.0

220 35 50 3.0 1.1 35 60 3.2 1.1
270 35 50 3.3 1.2 35 50 3.3 1.2 35 60 3.6 1.2
330 35 50 3.7 1.3 35 60 3.9 1.4 35 80 4.4 1.5
390 35 60 4.3 1.5 35 60 4.3 1.5 35 80 4.8 1.7
470 35 60 4.7 1.6 35 80 5.3 1.8 35 100 5.8 2.0
560 35 80 5.8 2.0 35 100 6.3 2.2 35 100 6.3 2.2
680 35 80 6.4 2.2 35 100 7.0 2.4 35 120 7.5 2.6
820 35 100 7.7 2.7 35 120 8.3 2.9 51 80 8.0 2.8
1000 35 120 9.2 3.2 51 80 8.8 3.1 51 80 9.6 3.4
1200 51 80 9.7 3.4 51 80 9.7 3.4 51 100 10.6 3.7
1500 51 80 10.8 3.8 51 100 11.8 4.1 51 100 12.7 4.4
1800 51 100 12.9 4.5 51 100 13.9 4.9 51 110 13.8 4.8
2200 51 120 15.4 5.4 51 120 16.4 5.7 51 120 16.3 5.7
2700 51 140 18.2 6.4 63.5 100 18.1 6.3 51 140 19.2 6.7
3300 63.5 120 20.0 7.0 63.5 120 21.3 7.4 63.5 120 20.6 7.2
3900 63.5 140 23.1 8.1 63.5 130 24.4 8.6 63.5 130 23.7 8.3
4700 63.5 160 26.8 9.4 76.2 120 26.0 9.1 76.2 120 27.5 9.6
5600 76.2 140 28.4 10.0 76.2 130 30.0 10.5 76.2 130 31.3 10.9
6800 76.2 160 33.0 11.6 76.2 140 34.5 12.1 76.2 140 36.3 12.7
8200 89 140 37.8 13.2 76.2 160 39.8 13.9
10000 89 160 44.0 15.4 89 140 44.0 15.4
WV
500
Item Ripple current

D L
(A rms)
(mm)
40 C 120Hz 85 C 120Hz
F
1000 51 120 12.2 4.2

1200 63.5 100 13.1 4.5
1500 63.5 100 14.8 5.1
1800 63.5 120 17.4 6.0
2200 63.5 140 20.3 7.0
2700 76.2 120 22.3 7.5
3300 76.2 140 26.1 8.8

Frequency
WV
~ 100 0.8 1.0 1.1 1.15 1.2

160 ~ 250 0.8 1.0 1.1 1.15 1.3
350 ~ 0.8 1.0 1.2 1.35 1.4
214
Upgrade
Screw Terminal Type, High Ripple

GK Series
Ideally suited for use as input and output filter capacitors in

power supplies
High ripple current capability
Suited for smoothing circuits for general purpose inverters
and control circuits for F.A. machines

Dissipation factor max. 0.25 max. at 120Hz, 20 C

DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
35 24 29 7 10 30 12.7 51 32.9 38.9 7 12 60 22

51 33.6 39.9 6 14 30 22 63.5 38.4 45.3 7 14 60 28.6
63.5 40.8 46.8 6 14 30 28.6 76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
215
GK series
WV 350 400 450 500
Item Ripple current Ripple current Ripple current Ripple current

D L D L D L D L
(A rms) (A rms) (A rms) (A rms)
(mm) (mm) (mm) (mm)
F 85 C 120Hz 85 C 120Hz 85 C 120Hz 85 C 120Hz
180 35 60 1.5
220 35 50 1.7 35 60 1.7
270 35 50 1.8 35 50 1.8 35 60 1.8
330 35 50 2.0 35 60 2.1 35 80 2.3
390 35 60 2.3 35 60 2.3 35 80 2.6
470 35 60 2.4 35 80 2.7 35 100 3.0
560 35 80 3.0 35 100 3.3 35 100 3.3
680 35 80 3.3 35 100 3.6 35 120 3.9
820 35 100 4.1 35 120 4.4 51 80 4.2
1000 35 100 4.8 51 80 4.7 51 80 5.1 51 120 5.5
1200 51 80 5.1 51 80 5.1 51 100 5.6 63.5 100 5.9
1500 51 80 5.7 51 100 6.2 51 100 6.6 63.5 100 6.6
1800 51 100 6.8 51 100 7.4 51 110 7.2 63.5 120 7.8
2200 51 100 8.1 51 120 8.6 51 120 8.6 63.5 140 9.1
2700 51 120 9.6 63.5 100 9.5 51 140 10.1 76.2 120 9.8
3300 63.5 100 10.5 63.5 120 11.1 63.5 120 10.8 76.2 140 11.4
3900 63.5 120 12.2 63.5 130 12.9 63.5 130 12.5 76.2 160 13.2
4700 63.5 130 14.1 76.2 120 13.7 76.2 120 14.4 89 140 15.3
5600 76.2 120 15.0 76.2 130 15.8 76.2 130 16.4 89 160 17.7
6800 76.2 130 17.4 76.2 140 18.2 76.2 140 19.1 89 160 20.5
8200 76.2 150 19.8 76.2 160 20.9
10000 76.2 160 23.1 89 140 23.1

Frequency 50Hz 120Hz 300Hz 1kHz 3kHz
Coefficient 0.8 1.0 1.1 1.3 1.4
216
Screw Terminal Type, High Ripple

GM Series
Ideally suited for use as input and output filter capacitors in power supplies
High ripple current compared with GK series
Suited for smoothing circuits for general purpose inverters,
control circuits for F.A. machines and medical equipment


DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 29
76.2 44.5 51.5 8 16 60 32
89 50.8 61 8 16 60 31.8
217
GM series
WV 350 400 450

D L D L D L
(mm) (mm) (mm)
F 85 C 120Hz 85 C 120Hz 85 C 120Hz
820 51 80 4.8
1000 51 80 5.3 51 100 5.8
1200 51 80 5.8 51 80 5.8 51 100 6.3
1500 51 80 6.5 51 100 7.0 51 120 7.5
1800 51 100 7.7 51 120 8.3 51 140 8.2
2200 51 120 9.2 51 140 9.7 63.5 100 8.9
2700 51 140 10.9 63.5 100 10.0 63.5 120 10.4
3300 63.5 100 11.0 63.5 120 11.6 63.5 130 11.7
3900 63.5 120 13.0 63.5 130 13.2 76.2 120 13.4
4700 63.5 130 14.5 76.2 120 14.7 76.2 130 15.5
5600 76.2 120 15.5 76.2 130 16.1 76.2 160 17.2
6800 76.2 130 17.8 76.2 160 19.0 76.2 170 19.4
8200 76.2 160 21.1 76.2 170 21.4
10000 76.2 170 23.8 89 160 25.0

Frequency 50Hz 120Hz 1kHz 3kHz
Coefficient 0.8 1.0 1.3 1.4
218
Upgrade
Screw Terminal Type, Wide Temperature Range

CU Series
Screw terminal series for high temperature up to 105 C

High ripple current capability
Ideally suited for use as input and output filter capacitors
in power supplies
WV 16 25 35 50 63 80 100 160 200, 250 350~500
D
35 0.50 0.45 0.40 0.30 0.25 0.25 0.20 0.15 0.15 0.25
51 0.70 0.60 0.45 0.45 0.35 0.30 0.20 0.15 0.15 0.25
(at 120Hz, 20 C)
63.5 1.00 0.80 0.60 0.50 0.40 0.35 0.25 0.20 0.20 0.25
76.2 1.60 1.20 0.80 0.75 0.70 0.50 0.40 0.35 0.25 0.25


DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
THREE LEGS ANGLE SIZE TABLE

TWO LEGS ANGLE SIZE TABLE D B A T U P
D B A T U P 51 32.9 38.9 7 12 60 22
35 24 29 7 10 30 12.7 63.5 38.4 45.3 7 14 60 28.6
51 33.6 39.9 6 14 30 22 76.2 44.5 51.5 8 16 60 31.8
63.5 40.8 46.8 6 14 30 28.6 89 50.8 61 8 16 60 31.8
219
CU series
WV
16 25 35 50
F
6800 35 50 3.1
10000 35 60 3.5 35 60 4.0
15000 35 50 3.8 35 80 4.8 35 80 5.5
22000 35 60 4.9 35 68 5.1 35 100 6.4 35 120 8.0
33000 35 80 6.7 35 100 7.4 35 120 8.5 51 100 8.3
47000 35 100 8.8 35 120 9.5 51 100 9.9 51 120 10.7
68000 51 80 9.5 51 100 10.3 51 120 12.8 63.5 100 12.6
100000 51 100 12.5 51 120 13.5 63.5 120 16.4 76.2 120 13.7
150000 51 140 17.6 63.5 120 16.9 76.2 120 16.8 76.2 140 17.9
220000 63.5 120 18.4 76.2 120 18.0 76.2 160 22.8
330000 76.2 120 19.1 76.2 160 24.6
470000 76.2 160 25.5
WV
63 80 100 160
F
1000 35 60 1.7
1500 35 60 1.9 35 68 2.1
2200 35 80 2.6 35 100 3.0
3300 35 100 3.5 35 120 4.0
4700 35 60 3.0 51 80 4.3 51 100 5.0
6800 35 60 3.7 35 80 4.1 51 100 5.7 51 140 7.0
10000 35 80 5.0 35 100 5.4 51 140 7.9 63.5 120 7.3
15000 35 120 7.2 51 80 6.3 63.5 140 9.2 76.2 120 7.0
22000 51 80 7.0 51 100 8.3 76.2 140 9.1 76.2 160 9.4
33000 51 120 10.1 51 140 11.7
47000 63.5 100 11.7 63.5 140 14.3
68000 63.5 140 16.0 76.2 140 14.2
100000 76.2 140 14.6
WV
200 250 350 400
F
1000 35 68 1.8 35 80 2.1 35 100 3.4 51 70 3.2

1500 35 80 2.3 35 100 2.6 51 80 4.4 51 80 4.8
2200 35 120 3.3 51 80 3.4 51 100 5.7 51 120 6.4
3300 51 100 4.2 51 120 4.8 63.5 100 7.8 63.5 120 10.5
4700 51 140 5.8 63.5 100 5.2 63.5 120 9.0 76.2 120 12.5
6800 63.5 120 6.2 63.5 120 5.5 76.2 120 12.4 76.2 140 15.1
10000 76.2 120 6.7 76.2 140 7.5
15000 76.2 160 9.2
WV
450 500
F
2200 63.5 100 6.7 63.5 130 7.0

2700 63.5 120 7.9 63.5 150 8.6
3300 63.5 140 9.4 76.2 130 9.7
3900 76.2 120 10.5 76.2 150 10.7
4700 76.2 130 11.9 89 150 12.0
5600 76.2 140 13.3
6800 89 140 14.9
Ripple current (A rms) at 105 C, 120Hz

Case size D L (mm)

Frequency
WV
~ 100 0.8 1.0 1.1 1.15 1.2

160 ~ 250 0.8 1.0 1.1 1.15 1.3
350 ~ 0.8 1.0 1.2 1.35 1.4
220
For Inverter Circuits

GF Series Long Life
Screw terminal series in compact case sizes

High reliability, long life guaranteed for 5000 hours load life at 85 C
500 ~ 600WV is assured 2000 hours at 85 C)
Suited for use in industrial power supplies for inverters

Load life

500~600WV products are for 2000 hours.
DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 28.6
76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
221
GF series

WV
350 400 450

D L D L D L
(mm) (mm) (mm)
2200 51 110 16.0 6.0 51 130 17.1 6.4 63.5 110 17.0 6.4
2700 51 130 18.9 7.1 63.5 110 18.9 7.1 63.5 130 20.0 7.5
3300 63.5 100 20.5 7.5 63.5 130 22.2 8.3 76.2 110 21.4 8.0
3900 63.5 100 23.2 8.2 76.2 100 24.2 8.4 76.2 130 24.7 8.3
4700 76.2 100 26.9 9.5 76.2 130 27.1 10.2 76.2 150 28.7 10.8
5600 76.2 110 28.9 10.5 76.2 150 31.3 11.8 76.2 160 32.5 12.1
6800 76.2 130 33.7 12.3 76.2 160 35.8 13.4 89 150 37.9 14.3
8200 76.2 160 38.3 14.7 89 150 41.6 15.7 89 160 42.6 16.1
10000 89 150 45.9 17.3 89 160 46.4 17.8
12000 89 160 51.7 19.5
WV
500 550 600

D L D L D L
(mm) (mm) (mm)
1000 51 120 12.2 4.2 51 130 12.2 4.2 63.5 130 17.1 5.9
1200 63.5 100 13.1 4.5 63.5 110 14.5 5.0 76.2 120 19.4 6.7
1500 63.5 100 14.8 5.1 63.5 130 17.4 6.0 76.2 140 23.4 8.1
1800 63.5 120 17.4 6.0 76.2 110 19.4 6.7 76.2 160 27.8 9.6
2200 63.5 140 20.3 7.0 76.2 130 23.2 8.0 76.2 160 31.0 10.7
2700 76.2 120 22.3 7.5 76.2 150 27.2 9.4 89 160 36.5 12.6
3300 76.2 140 26.1 8.8 76.2 160 31.9 11.0
3900 89 160 36.2 12.5

Coefficient 0.8 1.0 1.1 1.3 1.4
222
For inverter Circuits

GH Series Miniaturized Long Life

Miniature size, High ripple current compared with GF series
(500WV is assured 2000 hours at 85 C)

Leakage current Less than the specified value
Load life

500WV products are for 2000 hours
DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 28.6
76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
223
GH series

WV
F
400 450 500
1800 63.5 110 6.5
2200 51 100 8.4 51 130 8.6 63.5 130 7.7
2700 51 130 10.5 63.5 110 10.5 76.2 110 8.8
3300 63.5 100 11.6 63.5 120 11.9 76.2 130 10.4
3900 63.5 110 12.3 76.2 110 13.9 76.2 150 12.1
4700 63.5 130 14.5 76.2 120 15.5 89 130 13.7
5600 76.2 120 15.7 76.2 140 15.9 89 150 17.8
6800 76.2 130 17.5 76.2 160 18.4
8200 76.2 150 18.7 89 150 19.7
10000 89 150 20.5
12000 89 160 21.0

Case size D L (mm)

Coefficient 0.8 1.0 1.1 1.3 1.4
224
For Inverter, Miniature, High Ripple

GN Series Miniaturized Long Life
Miniature size, High ripple current compared with GH series

(500WV is assured 2000 hours at 85 C)

Load life

500WV products are for 2000 hours.

DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 28.6
76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
225
GN series

WV
400 450 500
F
1800 63.5 100 6.5
2200 51 100 8.4 51 120 8.6 63.5 120 7.7
2700 51 110 10.0 63.5 100 10.5 76.2 100 8.8
3300 63.5 100 11.6 63.5 110 11.9 76.2 120 10.4
3900 63.5 100 12.3 76.2 100 13.9 76.2 140 12.1
4700 63.5 120 14.5 76.2 110 15.5 89 120 13.7
5600 76.2 110 16.5 76.2 130 15.9 89 140 17.8
6800 76.2 120 17.5 76.2 150 18.4
8200 76.2 140 18.7 89 140 19.7
10000 89 140 20.5
12000 89 150 21.0

Case size D L (mm)

Coefficient 0.8 1.0 1.1 1.3 1.4
226
For Inverter, High Ripple

GQ Series Long Life
High ripple current compared with GN series


(after application of the rated Capacitance change Within 20% of the initial value
DRAWING Unit : mm

D 2 max.
P 1
Safety vent
L 4.5 max. M5 Hexagon head bolt
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 28.6
76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
227
GQ series

WV
400 450
F
1800
2200 51 100 10.9 51 120 7.3
2700 51 110 13.0 63.5 100 13.7
3300 63.5 100 15.1 63.5 110 15.5
3900 63.5 110 16.0 76.2 100 18.1
4700 63.5 130 18.9 76.2 110 20.2
5600 76.2 110 21.5 76.2 130 20.7
6800 76.2 130 22.8 76.2 150 23.9
8200 76.2 150 24.3 89 140 25.6
10000 89 140 26.7
12000 89 150 27.3

Case size D L (mm)

Coefficient 0.8 1.0 1.1 1.3 1.4
228
Screw Terminal Type, Long Life

GL Series Long Life



DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
LARGE TYPES
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 28.6
76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
229
GL series
WV 350 400 450

D L D L D L
(mm) (mm) (mm)
F 85 C 120Hz 85 C 120Hz 85 C 120Hz
1500 51 110 6.1
1800 51 110 6.6 51 130 7.1
2200 51 110 7.3 51 130 7.9 63.5 110 7.8
2700 51 130 8.7 63.5 110 8.7 63.5 130 9.2
3300 63.5 100 9.2 63.5 130 10.2 76.2 110 9.9
3900 63.5 110 10.4 76.2 100 10.3 76.2 130 11.4
4700 76.2 100 11.4 76.2 130 12.5 76.2 150 13.2
5600 76.2 110 12.8 76.2 150 14.5 76.2 160 14.8
6800 76.2 130 15.1 76.2 160 16.4 89 150 17.5
8200 76.2 150 18.0 89 150 19.2 89 160 19.7
10000 89 150 21.2 89 160 21.8
12000 89 160 23.9

Coefficient 0.8 1.0 1.1 1.3 1.4
230
High ripple Current, High Reliability

EV Series Long Life
High ripple current compared with CU series

Long life guaranteed for 5000 hours load life at 105 C
Suited for the general-purpose inverter

Leakage current max. I = 3 CV ( A) (after 5 minutes)
Load life
500WV products are for 2000hours
DRAWING Unit : mm
TWO LEGS ANGLE SIZE TABLE

D 2 max.
D B A T U P
P 1
51 33.6 39.9 6 14 30 22
Safety vent
63.5 40.8 46.8 6 14 30 28.6
M5 Hexagon head bolt
L 3 max. 6.0 1
TWO LEGS ANGLE THREE LEGS ANGLE THREE LEGS ANGLE SIZE TABLE
120 D B A T U P
T
51 32.9 38.9 7 12 60 22
63.5 38.4 45.3 7 14 60 28.6
3.5
U
4.5
76.2 44.5 51.5 8 16 60 31.8
B B T 89 50.8 61 8 16 60 31.8
A 1 A 1 U

WV 400 450 500
Item
Ripple Current Ripple Current Ripple Current
D L D L D L
F (mm) (mm) (mm)

105 C 120Hz 105 C 120Hz 105 C 120Hz
1000 51 130 6.3

1500 63.5 110 7.5
2200 63.5 110 11.6 63.5 115 12.1 76.2 130 10.1
2700 63.5 115 13.7 63.5 130 14.3 76.2 140 12.3
LARGE TYPES
3300 63.5 130 16.1 76.2 130 16.9 76.2 150 13.0
3900 63.5 140 18.1 76.2 140 20.5 89 160 15.0
4700 76.2 130 21.2 76.2 150 22.6 89 160 16.5
5600 76.2 150 24.3 76.2 160 25.2
6800 89 150 27.1 89 150 26.0

Coefficient 0.8 1.0 1.1 1.3 1.4
231
High Ripple, High Reliability Long Life

EY Series Long Life
High ripple current compared with EV Series

Suited for use in industrial power supplies for inverter

DRAWING Unit : mm

D 2 max.
P 1
Safety vent
6.0 1
120
T
3.5
U
4.5
B B T
A 1 A 1 U
51 33.6 39.9 6 14 30 22 51 32.9 38.9 7 12 60 22

63.5 40.8 46.8 6 14 30 28.6 63.5 38.4 45.3 7 14 60 28.6
76.2 44.5 51.5 8 16 60 31.8
89 50.8 61 8 16 60 31.8
232
EY series
WV 350 400 450

D L D L D L
(mm) (mm) (mm)
F 105 C 120Hz 105 C 120Hz 105 C 120Hz
1500 51 110 6.1
1800 51 110 7.4 51 130 7.1
2200 51 110 8.2 51 130 8.8 63.5 110 7.8
2700 51 130 9.8 63.5 110 9.7 63.5 130 9.2
3300 63.5 100 10.3 63.5 130 11.4 76.2 110 9.9
3900 63.5 110 11.6 76.2 100 11.6 76.2 130 11.4
4700 76.2 100 12.7 76.2 130 14.0 76.2 150 13.2
5600 76.2 110 14.3 76.2 150 16.2 76.2 160 14.8
6800 76.2 130 16.8 76.2 160 18.3 89 150 17.5
8200 76.2 150 20.1 89 150 21.5 89 160 19.7
10000 89 150 23.7 89 160 24.3
12000 89 160 26.7
LARGE TYPES

Coefficient 0.8 1.0 1.1 1.3 1.4
233
For Welding Machine

LW,SW Series
For welding machine applications

Charge and discharge characteristic : 100000 cycles at 5 ~ 35 C
LW series with lug terminal type, SW series with screw terminal type

Capacitance tolerance -10 ~ +50% at 120Hz, 20 C (Capacitance Tolerance “T”)
Dissipation factor max. 0.20 max.at 120Hz, 20 C
After charge and discharge for 100000 cycles at 5~35 C with application of the rate voltage,
the capacitors shall be satisfied the following specifications.
Leakage current Less than 150% of specified value
Charge and discharge
charateristics
Conditions
Charge resistance :4 Charge time : 1 sec
Discharge resistance : 0.12 Discharge time : 0.5sec
DRAWING Unit : mm
LW series
Insulating sleeve Terminal Safety vent
D 35 51
max.
P 14 18
D
1 2
2 3
L max. P 1
Bottom plate
SW series

D 2 max.
D 35 51 63.5 76.2
P 1
P 12.7 22 28.6 31.8
Safety vent
6.0 1
DIMENSIONS D L (mm)
WV
315 475
SERIES
LW SW LW SW
F
225 51 100 51 100
330 35 100
470 51 100 76.2 120
1000 63.5 140 76.2 160
1500 76.2 120
2200 76.2 160
234
For Hi-Fi Component System

AM Series For Audio Use Solvent Proof
For high grade audio equipment

High resonance frequency, low ESR and low impedance
Ideally suited for Hi-Fi VTR and CD players
Snap-in terminal type
Voltage range of 16~100V

Leakage current max. I = 3 CV ( A) (after 5 minutes)
Dissipation factor max. WV 16 25 ~ 35 50 ~ 71 80 ~ 100
(at 120Hz, 20 C) tan 0.25 0.22 0.20 0.15
After charge and discharge for 5000 cycles at 70 C with application of the rated voltage,
the capacitors shall be satisfied the following specifications.
Appearance No visible damage and no leakage electrolyte
characteristics
Conditions
Charge resistance : 4 Applied current : 1A
Discharge resistance : 100 Charge and discharge time : 60sec. (each)


DRAWING Unit : mm
PC Board Terminal
Insulating sleeve
Mounting Holes
Terminal 0.8 0.1
10 0.8
0.1
10
0.2
D 1 max.
6.0 1
2 2 0.1
Safety vent
L 2 max. 6.0 1
1.5 0.1
LARGE TYPES
235
AM series
DIMENSIONS D L(mm)
WV
16 25 35 50 63 80 100
F
470 22 40
680 22 40 25.4 40
1000 22 40 25.4 40 25.4 50
1500 22 40 25.4 40 25.4 50 30 50
2200 22 40 25.4 40 25.4 50 30 50 35 50
3300 22 40 25.4 40 25.4 50 30 50 30 60 35 60
4700 25.4 40 25.4 50 30 50 30 60 35 60
6800 22 40 25.4 50 30 50 30 60 35 60
8200 25.4 40 30 50 35 50 35 60 35 60
10000 25.4 50 35 50 35 60 35 60
12000 30 50 35 50 35 60
15000 35 50 35 60
22000 35 60
33000 35 60
236
For Photo Flash

DF Series
For photo flash applications with lug terminal

Low dissipation factor, low leakage current and high stability
during the repetition of charge and discharge

Capacitance tolerance -10 ~ +20% at 120Hz, 20 C
Leakage current max. I=1 C ( A) (after 5 minutes), where C=Nominal capacitance ( F)
Dissipation factor max. Capacitance range( F) 150 ~ 600 700 ~ 1500
(at 120Hz, 20 C) tan 0.10 0.15
Charge and discharge at rated voltage at 5~35 C with a switch sequence of 30 seconds for 5000
times via xenon flash tube with discharge resistance of 0.7~1.0
Leakage current Less than 150% of specified value
characteristics
After leaving capacitors under no load at 55 C for 1000 hours.
Shelf life Leakage current Less than 300% of specified value
DRAWING Unit : mm
D 22

D 1 max.
D=22 D 25.4 D 40
A 1
3.5 4.5 4.5

P 1
B 6.0 8.0 11.0

p 8.0 10.0 18.0
Safety vent L 2 max. B 1
Note : 40 is available upon request. Please check with us individual size and dimensions.
LARGE TYPES
237
DF series
DIMENSIONS D L(mm)
D
WV
22 25.4 30 35
(SV) F
200
250 22 27
300 22 30
350 22 33
400 22 36 25.4 30
450 22 42 25.4 33
500 22 44 25.4 37
330
(350)
600 25.4 42 30 33
700 25.4 47 30 38
800 25.4 54 30 42
900 25.4 57 30 45
1000 30 48 35 40
1200 30 58 35 45
1300 30 63 35 50
1500 30 70 35 55
200 22 27
250 22 30
300 22 36 25.4 30
350 22 40 25.4 33
400 22 42 25.4 35
450 22 48 25.4 40
500 25.4 44 30 35
360
600 25.4 54 30 38
(390)
700 25.4 57 30 45
800 30 50 35 40
900 30 55 35 45
1000 30 58 35 55
1200 30 70 35 55
1300 35 60
1500 35 70
238
NEW
For Inverter Air-conditionings

AR,AG
For high ripple current application such as air conditioning system
AR series is load life of 3000 hours at 85 C
AG series is load life of 5000 hours at 85 C

Dissipation factor WV 400 450
(120Hz, 20 C ) tan 0.15 0.20
The following specifications shall be satisfied when the capacitors are restored to 20 C after
subjected to DC voltage with the rated ripple current is applied for 3000/5000 hours at 85 C
Shelf life
DRAWING Unit : mm
Insulating sleeve
14.2
Terminal
D 1 max.
4.2
L 2 max. 4.5 1
Safety vent D 1 max.
SERIES
AR AG
WV
D 30 35 30 35
F
30 55 35 45
560
2.80 2.70
30 60 35 50 30 60 35 50
LARGE TYPES
680
3.20 3.10 3.50 3.50
400
30 70 35 60 30 70 35 60
820
4.00 4.00 4.00 4.00
35 70
1000
5.00
30 60 35 50 35 50
560
2.70 2.60 2.60
30 70 35 60 30 70 35 60
450 680
3.10 3.00 3.50 3.40
820
239

Aluminium Electrolytic Capacitor

Uploaded by

Copyright:

Available Formats

Aluminium Electrolytic Capacitor

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aluminium Electrolytic Capacitor

Uploaded by

Copyright:

Available Formats

2015-2장 2015.1.

20 03:35 PM 페이지31 태산아이인쇄그룹(국) 2261-2488 2400DPI 175LPI

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

Hi-CAP (Conductive Polymer Aluminum Electrolytic Capacitor)

2. Capacitor handling techniques

(3) Circuit board cleaning

3. Electrical characteristics comparison of Capacitors

Species High Frequency Temperature Allowable ripple Miniaturized

※ Superior ◉ Ordinary Inferior

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

PRECAUTIONS AND GUIDELINES (Conductive Polymer)

3) Use in High Reliable and Critical Applications

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

Rated voltage (VDC) 2.5 4 6.3 10 16 20 25 35

9) Charging and Discharging in Capacitor

10) Leakage current

11) Failures and Service Life

(1) Failure Modes

(2) Service Life

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

12) Capacitor Insulation

13) Capacitor Usage Environment

Before unseal After unseal

(2) LEAD Type

Before unseal After unseal

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

●Taping Specifications for Lead Type Polymer Capacitors

Applicable Drawing No. Ⅰ

● PACKAGING Q’ty(pcs.) / BOX

● BULK PACKING QUANTITY(PCS) / BOX ● CUTTING PACKING QUANTITY(PCS) / BOX

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

●Taping Specifications for SMD Type Polymer Capacitors (Vertical type)

● Reel(Taping Code : VR) ● Recommended Land Size

ØD×L A ØD×L Q’ty/Reel(pcs) Q’ty/Box(pcs) ØD×L A B C

●Recommendable reflow soldering temperature

250 Peak temperature

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

FA Chip type, With Conductive Polymer

・Low ESR, high ripple current

Resistance to soldering heat Leakage current Less than specified value

< Dimensions >

0.3 max. C±0.2

5×5.9 5 5.9 5.3 5.3 1.4 2.2 0.5~0.8

6.3 5.9 6.6 6.6 2.2 2.45 0.5~0.8

8×6.9 8 6.9 8.3 8.3 3.2 2.9 0.5~0.8

8×11.9 8 11.9 8.3 8.3 3.2 2.9 0.8~1.1

< Marking >

Series Code Series Code

Lot No. Lot No.

Negative Polarity Negative Polarity

(Ø4, Ø5) (Ø6.3, Ø8, Ø10)

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

● Table1. FA(SMD type) Series Characteristics List

● FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

CONDUCTIVE POLYMER ALUMINUM ELECTROLYTIC CAPACITORS

FH Chip type, Large Capacitance, Low ESR

・Large capacitance, Low ESR than FA Series

Resistance to soldering heat Leakage current Less than specified value

< Dimensions >

0.3 max. C±0.2 Size ØD L B C E A R