Statics and load tables

2
 3

STATICS AND
LOAD TABLES

Statics
and
Load
Tables

EUROPEAN COURT OF JUSTICE,

LUXEMBOURG
4 LOAD TABLES FOR STAIR TREADS

Determination of the bearing bars for the individual span widths, DIN EN 1991, S235
mesh spacing 33.3 x 33.3 mm

Industrial staircases, working platforms and walkways, Load 5.00 kN/m² / 2.0 kN point loading,
load 2.00 kN/m² / 1.5 kN point loading, residential building load 3.00 kN/m² / 2.0 kN point loading,
Tread DIN EN ISO 14122, RAL-GZ 638 - 2008 contact area 50 x 50 mm
length
[mm] Bearing bar/deflection [cm] Bearing bar/deflection [cm]
without sl.prot. with sl.prot. without sl.prot. with sl.prot.

500 30 x 2 / 0,06 30 x 2 / 0,07 30 x 3 / 0,08 30 x 3 / 0,09

600 30 x 2 / 0,10 30 x 2 / 0,12 35 x 3 / 0,10 35 x 3 / 0,12
700 30 x 2 / 0,16 30 x 3 / 0,15 35 x 3 / 0,16 40 x 3 / 0,14
800 30 x 3 / 0,18 30 x 3 / 0,22 40 x 3 / 0,18 45 x 3 / 0,16
900 30 x 3 / 0,26 35 x 3 / 0,23 45 x 3 / 0,16 45 x 3 / 0,18
1.000 35 x 3 / 0,26 35 x 3 / 0,31 45 x 3 / 0,22 45 x 3 / 0,25
1.100 35 x 3 / 0,34 40 x 3 / 0,30 45 x 3 / 0,29 50 x 3 / 0,27
1.200 45 x 2 / 0,39 45 x 3 / 0,34 50 x 3 / 0,31 50 x 3 / 0,35
1.250 45 x 3 / 0,34 45 x 3 / 0,40 50 x 3 / 0,35 60 x 3 / 0,26
1.300 45 x 3 / 0,39 50 x 3 / 0,36 50 x 3 / 0,39 60 x 3 / 0,29
1.400 50 x 3 / 0,40 50 x 3 / 0,47 60 x 3 / 0,32 60 x 3 / 0,37
1.500 60 x 3 / 0,33 60 x 3 / 0,38 60 x 3 / 0,40 60 x 3 / 0,45
1.600 60 x 3 / 0,41 60 x 3 / 0,47 60 x 3 / 0,48 60 x 3 / 0,55
1.700 60 x 3 / 0,51 60 x 3 / 0,58 60 x 3 / 0,58 60 x 4 / 0,52
1.800 60 x 4 / 0,55 60 x 5 / 0,51 60 x 4 / 0,55 60 x 5 / 0,51
1.900 60 x 5 / 0,55 70 x 3 / 0,53 60 x 5 / 0,55 70 x 3 / 0,53
2.000 70 x 3 / 0,59 70 x 4 / 0,52 70 x 3 / 0,59 70 x 4 / 0,52
2.100 70 x 4 / 0,56 70 x 5 / 0,52 70 x 4 / 0,56 70 x 5 / 0,52
2.200 70 x 5 / 0,55 70 x 5 / 0,62 70 x 5 / 0,55 70 x 5 / 0,62
2.300 80 x 4 / 0,57 80 x 5 / 0,51 80 x 4 / 0,57 80 x 5 / 0,51
2.500 90 x 5 / 0,51 90 x 5 / 0,55 90 x 5 / 0,51 90 x 5 / 0,55
3.000 110 x 5 / 0,58 120 x 5 / 0,48 110 x 5 / 0,58 120 x 5 / 0,48

The requirements of RAL GZ 638, September 2008 edi-

tion, are complied with (deflection f < l/300 and < 0.6
cm).

Selection instructions: If there is no clear assignment of

industrial or fire exit staircases, the values for industrial
staircases should always be used.

For intermediate sizes (e.g. tread length 735 mm – in-

dustrial staircase without slide protection), the next high-
er tread length (800 mm) should be taken as the basis
of assessment (bearing bar 30 x 3 mm).

Note:
The determination of the bearing bars for rescue and es-
cape staircases was carried out using the same calcula-
tion methods as for industrial staircases. As it concerns
the building supervisory area, this is only a preliminary
estimate and should be checked for the individual case.

SILICON, BITTERFELD
 5

Determination of the bearing bars for the individual span widths, DIN EN 1991, S235
mesh spacing 33,3 x 11,1 mm on TS 2 – 3 mm, mesh spacing 33,3 x 16,65 mm on TS 5 mm

Industrial staircase, working platforms and walkways, Load 5.00 kN/m² / 2.0 kN point loading,
load 2.00 kN/m² / 1.5 kN point loading, DIN EN ISO 14122, residential building load 3.00 kN/m² / 2.0 kN point loading,
Tread
RAL-GZ 638 - 2008 contact area 50 x 50
length
[mm] Bearing bar/deflection [cm] Bearing bar/deflection [cm]
without sl.prot. with sl.prot. without sl.prot. with sl.prot.

500 30 x 2 / 0,05 30 x 2 / 0,05 * 30 x 2 / 0,07 30 x 2 / 0,07 *

600 30 x 2 / 0,08 30 x 2 / 0,08 * 30 x 3 / 0,10 30 x 3 / 0,10 *
700 30 x 2 / 0,13 30 x 2 / 0,13 * 30 x 3 / 0,16 30 x 3 / 0,16 *
800 30 x 2 / 0,19 30 x 2 / 0,19 * 35 x 3 / 0,17 35 x 3 / 0,17 *
900 30 x 3 / 0,21 30 x 3 / 0,21 * 35 x 3 / 0,25 35 x 3 / 0,25 *
1.000 30 x 3 / 0,29 30 x 3 / 0,29 * 40 x 3 / 0,25 40 x 3 / 0,25 *
1.100 35 x 3 / 0,27 35 x 3 / 0,27 * 40 x 3 / 0,33 40 x 3 / 0,33 *
1.200 40 x 3 / 0,35 40 x 3 / 0,35 * 45 x 3 / 0,33 45 x 3 / 0,33 *
1.250 40 x 3 / 0,41 40 x 3 / 0,41 * 45 x 3 / 0,32 45 x 3 / 0,32 *
1.300 45 x 2 / 0,43 45 x 2 / 0,43 * 45 x 3 / 0,36 45 x 3 / 0,36 *
1.400 45 x 3 / 0,41 45 x 3 / 0,41 * 45 x 3 / 0,45 45 x 3 / 0,45 *
1.500 50 x 3 / 0,41 50 x 3 / 0,41 * 50 x 3 / 0,44 50 x 3 / 0,44 *
1.600 50 x 3 / 0,51 50 x 3 / 0,51 * 50 x 3 / 0,54 50 x 3 / 0,54 *
1.700 60 x 3 / 0,40 60 x 3 / 0,40 * 60 x 3 / 0,42 60 x 3 / 0,42 *
1.800 60 x 3 / 0,56 60 x 3 / 0,56 * 60 x 3 / 0,56 60 x 3 / 0,56 *
1.900 60 x 4 / 0,56 60 x 4 / 0,56 * 60 x 4 / 0,56 60 x 4 / 0,56 *
2.000 60 x 5 / 0,55 60 x 5 / 0,55 * 60 x 5 / 0,55 60 x 5 / 0,55 *
2.100 70 x 3 / 0,57 70 x 3 / 0,57 * 70 x 3 / 0,57 70 x 3 / 0,57 *
2.200 70 x 4 / 0,56 70 x 4 / 0,56 * 70 x 4 / 0,56 70 x 4 / 0,56 *
2.300 70 x 5 / 0,55 70 x 5 / 0,55 * 70 x 5 / 0,55 70 x 5 / 0,55 *
2.500 80 x 5 / 0,58 80 x 5 / 0,58 * 80 x 5 / 0,58 80 x 5 / 0,58 *
3.000 110 x 5 / 0,49 110 x 5 / 0,49 * 110 x 5 / 0,49 110 x 5 / 0,49 *

* Slide protection only on the cross bar

Statics
and
Load
Tables
6 LOAD TABLE PRESS LOCKED GRATING / STEEL

Press locked grating mesh spacing 33.3 x 33.3 mm, DIN EN 1991 S235 JR+N St 37-2

Bearing bars Width between supports [mm]

[mm] 200 300 400 500 600 700 800 900 1.000 1.100

FP 4,25 2,13 1,42 1,06 0,85 0,71 0,61 0,42 0,31 0,23
20/2
FV 70,71 31,43 17,68 11,31 7,86 5,77 3,91 2,44 1,60 1,09
FP 7,02 3,51 2,34 1,76 1,40 1,17 0,91 0,63 0,46 0,34
20/3
FV 116,67 51,85 29,17 18,67 12,96 8,75 5,86 3,66 2,40 1,64
FP 9,89 4,94 3,30 2,47 1,98 1,65 1,41 1,23 0,89 0,67
25/2
FV 165,73 73,66 41,43 26,52 18,41 13,53 10,36 7,15 4,69 3,20
FP 16,31 8,16 5,44 4,08 3,26 2,72 2,33 1,84 1,34 1,00
25/3
FV 273,45 121,53 68,36 43,75 30,38 22,32 17,09 10,73 7,04 4,81
FP 14,11 7,06 4,70 3,53 2,82 2,35 2,02 1,76 1,53 1,14
30/2
FV 238,65 106,07 59,66 38,18 26,52 19,48 14,92 11,79 8,11 5,54
FP 23,29 11,64 7,76 5,82 4,66 3,88 3,33 2,91 2,29 1,72
30/3
FV 393,77 175,01 98,44 63,00 43,75 32,14 24,61 18,54 12,16 8,31
FP 31,05 15,53 10,35 7,76 6,21 5,18 4,44 3,88 3,05 2,29
30/4
FV 525,03 233,35 131,26 84,00 58,34 42,86 32,81 24,71 16,21 11,07
FP 38,81 19,41 12,94 9,70 7,76 6,47 5,54 4,85 3,82 2,86
30/5
FV 656,29 291,68 164,07 105,01 72,92 53,57 41,02 30,89 20,27 13,84
FP 19,02 9,51 6,34 4,76 3,80 3,17 2,72 2,38 2,11 1,80
35/2
FV 324,83 144,37 81,21 51,97 36,09 26,52 20,30 16,04 12,87 8,79
FP 31,39 15,69 10,46 7,85 6,28 5,23 4,48 3,92 3,49 2,70
35/3
FV 535,97 238,21 133,99 85,75 59,55 43,75 33,50 26,47 19,31 13,19
FP 41,85 20,93 13,95 10,46 8,37 6,98 5,98 5,23 4,65 3,60
35/4
FV 714,62 317,61 178,66 114,34 79,40 58,34 44,66 35,29 25,75 17,59
FP 52,31 26,16 17,44 13,08 10,46 8,72 7,47 6,54 5,81 4,50
35/5
FV 893,28 397,07 223,32 142,92 99,25 72,92 55,83 44,11 32,19 21,98
FP 24,63 12,31 8,21 6,16 4,93 4,10 3,52 3,08 2,74 2,46
40/2
FV 424,27 188,56 106,07 67,88 47,14 34,63 26,52 20,95 16,97 13,13
FP 40,64 20,32 13,55 10,16 8,13 6,77 5,81 5,08 4,52 3,99
40/3
FV 700,04 311,13 175,01 112,01 77,78 57,15 43,75 34,57 28,00 19,69
FP 54,18 27,09 18,06 13,55 10,84 9,03 7,74 6,77 6,02 5,32
40/4
FV 933,38 414,84 233,35 149,34 103,71 76,19 58,34 46,09 37,34 26,25
FP 67,73 33,86 22,58 16,93 13,55 11,29 9,68 8,47 7,53 6,65
40/5
FV 1166,73 518,55 291,68 186,68 129,64 95,24 72,92 57,62 46,67 32,81
FP 67,96 33,98 22,65 16,99 13,59 11,33 9,71 8,50 7,55 6,80
45/4
FV 1181,31 525,03 295,33 189,01 131,26 96,43 73,83 58,34 47,25 37,38
FP 37,75 18,88 12,58 9,44 7,55 6,29 5,39 4,72 4,19 3,78
50/2
FV 662,91 294,63 165,73 106,07 73,66 54,12 41,43 32,74 26,52 21,91
FP 62,29 31,15 20,76 15,57 12,46 10,38 8,90 7,79 6,92 6,23
50/3
FV 1093,81 486,14 273,45 175,01 121,53 89,29 68,36 54,02 43,75 36,16
FP 83,06 41,53 27,69 20,76 16,61 13,84 11,87 10,38 9,23 8,31
50/4
FV 1458,41 648,18 364,60 233,35 162,05 119,05 91,15 72,02 58,34 48,21
FP 103,82 51,91 34,61 25,96 20,76 17,30 14,83 12,98 11,54 10,38
50/5
FV 1823,01 810,23 455,75 291,68 202,56 148,82 113,94 90,03 72,92 60,26
FP 88,08 44,04 29,36 22,02 17,62 14,68 12,58 11,01 9,79 8,81
60/3
FV 1575,08 700,04 393,77 252,01 175,01 128,58 98,44 77,78 63,00 52,07
FP 117,44 58,72 39,15 29,36 23,49 19,57 16,78 14,68 13,05 11,74
60/4
FV 2100,11 933,38 525,03 336,02 233,35 171,44 131,26 103,71 84,00 69,43
FP 146,80 73,40 48,93 36,70 29,36 24,47 20,97 18,35 16,31 14,68
60/5
FV 2625,14 1166,73 656,29 420,02 291,68 214,30 164,07 129,64 105,01 86,78
FP 117,54 58,77 39,18 29,38 23,51 19,59 16,79 14,69 13,06 11,75
70/3
FV 2143,86 952,83 535,97 343,02 238,21 175,01 133,99 105,87 85,75 70,87
FP 156,71 78,36 52,24 39,18 31,34 26,12 22,39 19,59 17,41 15,67
70/4
FV 2858,49 1270,44 714,62 457,36 317,61 233,35 178,66 141,16 114,34 94,50
FP 195,89 97,95 65,30 48,97 39,18 32,65 27,98 24,49 21,77 19,59
70/5
FV 3573,11 1588,05 893,28 571,70 397,01 291,68 223,32 176,45 142,92 118,12

The table applies to the standard mesh spacing of 33.3 x 33.3 and material S235 JR+N St 37-2. The values represent
the maximum permitted load-bearing capacity of the grating.
 7

Press locked grating mesh spacing 33.3 x 33.3 mm, DIN EN 1991 S235 JR+N St 37-2

Bearing bars Width between supports [mm]

[mm] 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000

FP 0,18 0,14 0,11 0,09 0,07 0,06 0,05 0,04 0,04

20/2
FV 0,77 0,56 0,42 0,32 0,24 0,19 0,15 0,12 0,10
FP 0,26 0,21 0,17 0,14 0,11 0,09 0,08 0,07 0,06
20/3
FV 1,16 0,84 0,63 0,47 0,37 0,29 0,23 0,18 0,15
FP 0,51 0,40 0,32 0,26 0,22 0,18 0,15 0,13 0,11
25/2
FV 2,26 1,64 1,22 0,93 0,72 0,56 0,45 0,36 0,29
FP 0,77 0,60 0,48 0,39 0,32 0,27 0,23 0,19 0,16
25/3
FV 3,39 2,46 1,83 1,39 1,07 0,84 0,67 0,54 0,44
FP 0,88 0,69 0,55 0,45 0,37 0,31 0,26 0,22 0,19
30/2
FV 3,91 2,84 2,11 1,60 1,24 0,97 0,77 0,62 0,51
FP 1,32 1,03 0,83 0,67 0,55 0,46 0,39 0,33 0,28
30/3
FV 5,86 4,26 3,17 2,40 1,86 1,46 1,16 0,93 0,76
FP 1,76 1,38 1,10 0,90 0,74 0,61 0,52 0,44 0,38
30/4
FV 7,82 5,68 4,22 3,20 2,47 1,94 1,54 1,24 1,01
FP 2,20 1,72 1,38 1,12 0,92 0,77 0,65 0,55 0,47
30/5
FV 9,77 7,10 5,28 4,00 3,09 2,43 1,93 1,56 1,27
FP 1,38 1,08 0,87 0,70 0,58 0,48 0,41 0,35 0,30
35/2
FV 6,21 4,51 3,35 2,54 1,96 1,54 1,23 0,99 0,80
FP 2,07 1,63 1,30 1,06 0,87 0,72 0,61 0,52 0,44
35/3
FV 9,31 6,76 5,03 3,81 2,95 2,31 1,84 1,48 1,21
FP 2,76 2,17 1,73 1,41 1,16 0,97 0,81 0,69 0,59
35/4
FV 12,42 9,02 6,70 5,09 3,93 3,08 2,45 1,98 1,61
FP 3,45 2,71 2,17 1,76 1,45 1,21 1,02 0,86 0,74
35/5
FV 15,52 11,27 8,38 6,36 4,91 3,85 3,07 2,47 2,01
FP 2,04 1,60 1,28 1,04 0,86 0,71 0,60 0,51 0,44
40/2
FV 9,27 6,73 5,00 3,80 2,93 2,30 1,83 1,47 1,20
FP 3,07 2,41 1,92 1,56 1,29 1,07 0,90 0,77 0,66
40/3
FV 13,90 10,09 7,50 5,69 4,40 3,45 2,75 2,21 1,80
FP 4,09 3,21 2,57 2,08 1,72 1,43 1,20 1,02 0,88
40/4
FV 18,54 13,46 10,00 7,59 5,86 4,60 3,66 2,95 2,40
FP 5,11 4,01 3,21 2,60 2,14 1,79 1,50 1,28 1,09
40/5
FV 23,17 16,82 12,51 9,49 7,33 5,75 4,58 3,69 3,00
FP 5,77 4,53 3,62 2,94 2,42 2,02 1,70 1,44 1,24
45/4
FV 26,39 19,16 14,25 10,81 8,35 6,55 5,21 4,20 3,42
FP 3,43 3,08 2,46 2,00 1,64 1,37 1,15 0,98 0,84
50/2
FV 18,10 13,14 9,77 7,41 5,73 4,49 3,58 2,88 2,35
FP 5,66 4,61 3,69 2,99 2,46 2,05 1,73 1,47 1,26
50/3
FV 27,15 19,71 14,66 11,12 8,59 6,74 5,36 4,32 3,52
FP 7,55 6,15 4,92 3,99 3,29 2,74 2,30 1,96 1,68
50/4
FV 36,20 26,28 19,54 14,83 11,45 8,99 7,15 5,76 4,69
FP 9,44 7,69 6,15 4,99 4,11 3,42 2,88 2,45 2,10
50/5
FV 45,25 32,85 24,43 18,54 14,32 11,23 8,94 7,20 5,86
FP 8,01 7,34 6,26 5,08 4,18 3,48 2,93 2,49 2,14
60/3
FV 43,75 34,06 25,32 19,22 14,84 11,65 9,27 7,47 6,08
FP 10,68 9,79 8,34 6,77 5,58 4,65 3,91 3,32 2,85
Statics
60/4
FV 58,34 45,42 33,77 25,62 19,79 15,53 12,36 9,95 8,11
and
FP 13,35 12,23 10,43 8,47 6,97 5,81 4,89 4,15 3,56
Load
60/5
FV 72,92 56,77 42,21 32,03 24,74 19,41 15,45 12,44 10,13
Tables
FP 10,69 9,79 9,04 7,91 6,51 5,42 4,57 3,88 3,32
70/3
FV 59,55 50,74 40,21 30,52 23,57 18,50 14,72 11,85 9,66
FP 14,25 13,06 12,05 10,55 8,68 7,23 6,09 5,17 4,43
70/4
FV 79,40 67,66 53,62 40,69 31,43 24,66 19,62 15,81 12,87
FP 17,81 16,32 15,07 13,18 10,85 9,04 7,61 6,47 5,54
70/5
FV 99,25 84,57 67,02 50,86 39,29 30,83 24,53 19,76 16,09

Legend for conversion values: see page 8/9.

8 LOAD TABLE PRESS LOCKED GRATING / STEEL

Press locked grating mesh spacing 33.3 x 33.3 mm, DIN EN 1991 S235 JR+N St 37-2

Bearing bars Width between supports [mm]

[mm] 200 300 400 500 600 700 800 900 1.000 1.100

FP 200,60 100,30 66,87 50,15 40,12 33,43 28,66 25,07 22,29 20,06
80/4
FV 3733,53 1659,35 933,38 597,37 414,84 304,78 233,35 184,37 149,34 123,42
FP 250,75 125,37 83,58 62,69 50,15 41,79 35,82 31,34 27,86 25,07
80/5
FV 4666,92 2074,19 1166,73 746,71 518,55 380,97 291,68 230,47 186,68 154,28
FP 249,01 124,50 83,00 62,25 49,80 41,50 35,57 31,13 27,67 24,90
90/4
FV 4725,25 2100,11 1181,31 756,04 525,03 385,73 295,33 233,35 189,01 156,21
FP 311,26 155,63 103,75 77,82 62,25 51,88 44,47 38,91 34,58 31,13
90/5
FV 5906,57 2625,14 1476,64 945,05 656,29 482,17 369,16 291,68 236,26 195,26
FP 363,00 188,14 125,43 94,07 75,26 62,71 53,75 47,04 41,81 37,63
100/5
FV 7292,06 3240,91 1823,01 1166,73 810,23 595,27 455,75 360,10 291,68 241,06
FP 399,30 227,65 151,77 113,83 91,06 75,88 65,04 56,91 50,59 45,53
110/5
FV 8823,39 3921,51 2205,85 1411,74 981,38 720,28 551,46 435,72 352,94 291,68
FP 435,50 270,92 180,62 135,46 108,37 90,31 77,41 67,73 60,21 54,18
120/5
FV 10500,56 4666,92 2625,14 1680,09 1166,73 857,19 656,29 518,55 420,02 347,13
FP 471,00 317,96 211,97 158,98 127,18 105,99 90,85 79,49 70,66 63,59
130/5
FV 11760,00 5477,15 3080,89 1971,77 1369,29 1006,01 770,22 608,57 492,94 407,39
FP 508,00 368,76 245,84 184,38 147,50 122,92 105,36 92,19 81,95 73,75
140/5
FV 12700,00 6352,19 3573,11 2286,79 1588,05 1166,73 893,28 705,80 571,70 472,48
FP 544,00 423,32 282,21 211,66 169,33 141,11 120,95 105,83 94,07 84,66
150/5
FV 13610,00 7292,06 4101,78 2625,14 1823,01 1339,36 1025,45 810,23 656,29 542,38
FP 580,00 481,64 321,09 240,82 192,66 160,55 137,61 120,41 107,03 96,33
160/5
FV 14520,00 8296,74 4666,92 2986,83 2074,19 1523,89 1166,73 921,86 746,71 617,11
FP 617,00 543,73 362,49 271,86 217,49 181,24 155,36 135,93 120,83 108,75
170/5
FV 15420,00 9366,24 5268,51 3371,85 2341,56 1720,33 1317,13 1040,69 842,96 696,66

The table applies to the standard mesh spacing of 33.3 x 33.3 and material S235 JR+N St 37-2. The values represent
the maximum permitted load-bearing capacity of the grating.

Simply select the grating based on your characteristic action Qk from the tables.
All required partial safety factors have already been taken into account.

FP (Qk) and FV (Qk), for the individual spans, were determined according to RAL-GZ 638 - 2008 and DIN EN 1993-
1-1(3) + NA (Germany).

FP (Qk) is the maximum individual load in kN on a load cube of 200 x 200 mm.

FV (Qk) is the maximum uniformly distributed area load in kN/m².

FP (Qk) and FV (Qk) were determined either by load capacity or serviceability (4mm or L/200th criterion).

For the load of gratings made of the material S355 JR, the maximum load to the left of the black line can be multiplied
by 1.5.

The support width for gratings should correspond to the grating height, but at least 30 mm (BGI/GUV-I 588-1).

This is just an excerpt from our load tables. The complete tables can be found in the download area of our website at
www.meiser.co.uk.
 9

Press locked grating mesh spacing 33.3 x 33.3 mm, DIN EN 1991 S235 JR+N St 37-2

Bearing bars Width between supports [mm]

[mm] 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000

FP 18,24 16,72 15,43 14,33 12,70 10,58 8,91 7,57 6,48

80/4
FV 103,71 88,37 76,19 60,74 46,92 36,81 29,29 23,59 19,22
FP 22,80 20,90 19,29 17,91 15,88 13,22 11,13 9,46 8,11
80/5
FV 129,64 110,46 95,24 75,92 58,65 46,02 36,61 29,49 24,02
FP 22,64 20,75 19,15 17,79 16,60 14,77 12,44 10,57 9,06
90/4
FV 131,26 111,84 96,43 84,00 66,80 52,42 41,70 33,59 27,36
FP 28,30 25,94 23,94 22,23 20,75 18,47 15,55 13,21 11,32
90/5
FV 164,07 139,80 120,54 105,01 83,50 65,52 52,13 41,99 34,20
FP 34,21 31,36 28,94 26,88 25,09 23,52 20,88 17,74 15,21
100/5
FV 202,56 172,59 148,82 129,64 113,94 89,88 71,51 57,60 46,92
FP 41,39 37,94 35,02 32,52 30,35 28,46 26,78 23,62 20,24
110/5
FV 245,09 208,84 180,07 156,86 137,87 119,63 95,18 76,67 62,45
FP 49,26 45,15 41,68 38,70 36,12 33,87 31,87 30,10 26,28
120/5
FV 291,68 248,53 214,30 186,68 164,07 145,34 123,57 99,54 81,07
FP 57,81 52,99 48,92 45,42 42,39 39,74 37,41 35,33 33,41
130/5
FV 342,32 291,68 251,50 219,09 192,56 170,57 152,14 126,55 103,08
FP 67,05 61,46 56,73 52,68 49,17 46,09 43,38 40,97 38,82
140/5
FV 397,01 338,28 291,68 254,09 223,32 197,82 176,45 158,06 128,74
FP 76,97 70,55 65,13 60,47 56,44 52,91 49,80 47,04 44,56
150/5
FV 455,75 388,33 334,84 291,68 256,36 227,09 202,56 181,80 158,35
FP 87,57 80,27 74,10 68,81 64,22 60,21 56,66 53,52 50,70
160/5
FV 518,55 441,84 380,97 331,87 291,68 258,38 230,47 206,84 186,68
FP 98,86 90,62 83,65 77,68 72,50 67,97 63,97 60,41 57,23
170/5
FV 585,39 498,79 430,08 374,65 329,28 291,68 260,17 233,51 210,74

Legend for conversion values: see page 8/9.

Conversion values: Accessible area with a point loading of 1.5 kN on a

1 kN ≙ 100 kg 200 x 200 mm load cube with a deflection ≤ 4 mm
according to BGI 588 and RAL GZ 637.
10 KN ≙ 1 to
10 N ≙1 daN ≙ 1 kp Area with a point loading of 1.5 kN on a 200 x 200
The width between supports mm load cube with a deflection ≤ L/200.

Statics
and
Load
Tables

Lichte
Stützw
eite
Stützw
eite
10 LOAD TABLE PRESS WELDED GRATING

Press welded grating mesh spacing 34.3 x 38.1 mm, DIN EN 1991 S235 JR+N St 37-2

Bearing bars Width between supports [mm]

[mm] 200 300 400 500 600 700 800 900 1.000 1.100

FP 6,14 3,07 2,05 1,53 1,23 1,02 0,87 0,61 0,44 0,33
20/2
FV 114,53 50,90 28,63 18,32 12,73 9,35 6,33 3,95 2,59 1,77
FP 10,13 5,06 3,38 2,53 2,03 1,69 1,31 0,92 0,66 0,50
20/3
FV 188,97 83,99 47,24 30,23 21,00 14,18 9,50 5,93 3,89 2,66
FP 9,52 4,76 3,17 2,38 1,90 1,59 1,36 1,18 0,86 0,64
25/2
FV 178,95 79,53 44,74 28,63 19,88 14,61 11,18 7,72 5,07 3,46
FP 15,71 7,85 5,24 3,93 3,14 2,62 2,24 1,77 1,29 0,96
25/3
FV 295,26 131,23 73,82 47,24 32,81 24,10 18,45 11,58 7,60 5,19
FP 13,61 6,80 4,54 3,40 2,72 2,27 1,94 1,70 1,47 1,10
30/2
FV 257,68 114,53 64,42 41,23 28,63 21,04 16,10 12,73 8,75 5,98
FP 22,45 11,22 7,48 5,61 4,49 3,74 3,21 2,81 2,21 1,65
30/3
FV 425,18 188,97 106,29 68,03 47,24 34,71 26,57 20,01 13,13 8,97
FP 29,93 14,97 9,98 7,48 5,99 4,99 4,28 3,74 2,94 2,21
30/4
FV 566,90 251,96 141,73 90,70 62,99 46,28 35,43 26,68 17,51 11,96
FP 37,42 18,71 12,47 9,35 7,48 6,24 5,35 4,68 3,68 2,76
30/5
FV 708,63 314,95 177,16 113,38 78,74 57,85 44,29 33,36 21,88 14,95
FP 18,35 9,18 6,12 4,59 3,67 3,06 2,62 2,29 2,04 1,74
35/2
FV 350,68 155,88 87,68 56,12 38,97 28,63 21,92 17,32 13,90 9,49
FP 30,29 15,14 10,10 7,57 6,06 5,05 4,33 3,79 3,37 2,60
35/3
FV 578,72 257,21 144,68 92,59 64,30 47,24 36,17 28,58 20,85 14,24
FP 40,38 20,19 13,46 10,10 8,08 6,73 5,77 5,05 4,49 3,47
35/4
FV 771,62 342,94 192,91 123,46 85,74 62,99 48,23 38,10 27,80 18,99
FP 50,48 25,24 16,83 12,62 10,10 8,41 7,21 6,31 5,61 4,34
35/5
FV 964,53 428,68 241,13 154,32 107,17 78,74 60,28 47,63 34,75 23,74
FP 23,79 11,90 7,93 5,95 4,76 3,97 3,40 2,97 2,64 2,38
40/2
FV 458,11 203,60 114,53 73,30 50,90 37,40 28,63 22,62 18,32 14,17
FP 39,26 19,63 13,09 9,81 7,85 6,54 5,61 4,91 4,36 3,86
40/3
FV 755,87 335,94 188,97 120,94 83,99 61,70 47,24 37,33 30,23 21,26
FP 52,35 26,17 17,45 13,09 10,47 8,72 7,48 6,54 5,82 5,14
40/4
FV 1007,83 447,92 251,96 161,25 111,98 82,27 62,99 49,77 40,31 28,35
FP 65,43 32,72 21,81 16,36 13,09 10,91 9,35 8,18 7,27 6,43
40/5
FV 1259,79 559,91 314,95 201,57 139,98 102,84 78,74 62,21 50,39 35,43
FP 65,74 32,87 21,91 16,44 13,15 10,96 9,39 8,22 7,30 6,57
45/4
FV 1275,54 566,90 318,88 204,09 141,73 104,13 79,72 62,99 51,02 40,36
FP 36,61 18,30 12,20 9,15 7,32 6,10 5,23 4,58 4,07 3,66
50/2
FV 715,79 318,13 178,95 114,53 79,53 58,43 44,74 35,35 28,63 23,66
FP 60,40 30,20 20,13 15,10 12,08 10,07 8,63 7,55 6,71 6,04
50/3
FV 1181,05 524,91 295,26 188,97 131,23 96,41 73,82 58,32 47,24 39,04
FP 80,54 40,27 26,85 20,13 16,11 1,42 11,51 10,07 8,95 8,05
50/4
FV 1574,74 699,88 393,68 251,96 174,97 128,55 98,42 77,76 62,99 52,06
FP 100,67 50,34 33,56 25,17 20,13 16,78 14,38 12,58 11,19 10,07
50/5
FV 1968,42 874,85 492,10 314,95 218,71 160,69 123,03 97,21 78,74 65,07
FP 85,51 42,86 28,50 21,38 17,10 14,25 12,22 10,69 9,50 8,55
60/3
FV 1700,71 755,87 425,18 272,11 188,97 138,83 106,29 83,99 68,03 56,22
FP 114,02 57,01 38,01 28,50 22,80 19,00 16,29 14,25 12,67 11,40
60/4
FV 2267,62 1007,83 566,90 362,82 251,96 185,11 141,73 111,98 90,70 74,96
FP 142,52 71,26 47,51 35,63 28,50 23,75 20,36 17,82 15,84 14,25
60/5
FV 2834,52 1259,79 708,63 453,2 314,95 231,39 177,16 139,98 113,38 93,70
FP 114,55 57,27 38,18 28,64 22,91 19,09 16,36 14,32 12,73 11,45
70/3
FV 2314,86 1028,83 578,72 370,38 257,21 188,97 144,68 114,31 92,59 76,52
FP 152,73 76,37 50,91 38,18 30,55 25,46 21,82 19,09 16,97 15,27
70/4
FV 3086,48 1371,77 771,62 493,84 342,94 251,86 192,91 152,42 123,46 102,03
FP 190,92 95,46 63,64 47,73 38,18 31,82 27,27 23,86 21,21 19,09
70/5
FV 3858,10 1714,71 964,53 617,30 428,68 314,95 241,13 190,52 154,32 127,54
FP 196,01 98,01 65,34 49,00 39,20 32,67 28,00 24,50 21,78 19,60
80/4
FV 4031,32 1791,70 1007,83 645,01 447,92 329,09 251,96 199,08 161,25 133,27
FP 245,02 122,51 81,67 61,25 49,00 40,84 35,00 30,63 27,22 24,50
80/5
FV 5039,16 2239,62 1259,79 806,26 559,91 411,36 314,95 248,85 201,57 166,58

The table applies to the standard mesh spacing of 34.3 x 38.1 and material S235 JR + N St 37-2. The values repre-
sent the maximum permitted load-bearing capacity of the grating.
 11

Press welded grating mesh spacing 34.3 x 38.1 mm, DIN EN 1991 S235 JR+N St 37-2

Bearing bars Width between supports [mm]

[mm] 1.200 1.300 1.400 1.500 1.600 1.700 1.800 1.900 2.000

FP 0,25 0,20 0,16 0,13 0,11 0,09 0,07 0,06 0,05

20/2
FV 1,25 0,91 0,68 0,51 0,40 0,31 0,25 0,20 0,16
FP 0,38 0,30 0,24 0,19 0,16 0,13 0,11 0,10 0,08
20/3
FV 1,88 1,36 1,01 0,77 0,59 0,47 0,37 0,30 0,24
FP 0,49 0,39 0,31 0,25 0,21 0,17 0,15 0,12 0,11
25/2
FV 2,44 1,77 1,32 1,00 0,77 0,61 0,48 0,39 0,32
FP 0,74 0,58 0,46 0,38 0,31 0,26 0,22 0,19 0,16
25/3
FV 3,66 2,66 1,98 1,50 1,16 0,91 0,72 0,58 0,47
FP 0,85 0,67 0,53 0,43 0,36 0,30 0,25 0,21 0,18
30/2
FV 4,22 3,07 2,28 1,73 1,34 1,05 0,83 0,67 0,55
FP 1,27 1,00 0,80 0,65 0,53 0,44 0,37 0,32 0,27
30/3
FV 6,33 4,60 3,42 2,59 2,00 1,57 1,25 1,01 0,82
FP 1,69 1,33 1,06 0,86 0,71 0,59 0,50 0,42 0,36
30/4
FV 8,44 6,13 4,56 3,46 2,67 2,10 1,67 1,34 1,09
FP 2,12 1,66 1,33 1,08 0,89 0,74 0,62 0,53 0,45
30/5
FV 10,55 7,66 5,70 4,32 3,34 2,62 2,08 1,68 1,37
FP 1,33 1,05 0,84 0,68 0,56 0,47 0,39 0,33 0,29
35/2
FV 6,70 4,87 3,62 2,75 2,12 1,66 1,32 1,07 0,87
FP 2,00 1,57 1,26 1,02 0,84 0,70 0,59 0,50 0,43
35/3
FV 10,06 7,30 5,43 4,12 3,18 2,50 1,99 1,60 1,30
FP 2,67 2,09 1,67 1,36 1,12 0,93 0,78 0,67 0,57
35/4
FV 13,41 9,73 7,24 5,49 4,24 3,33 2,65 2,13 1,74
FP 3,33 2,62 2,09 1,70 1,40 1,16 0,98 0,83 0,71
35/5
FV 16,76 12,17 9,05 6,86 5,30 4,16 3,31 2,67 2,17
FP 1,98 1,55 1,24 1,01 0,83 0,69 0,58 0,49 0,42
40/2
FV 10,01 7,27 5,40 4,10 3,17 2,48 1,98 1,59 1,30
FP 2,96 2,33 1,86 1,51 1,24 1,04 0,87 0,74 0,63
40/3
FV 15,01 10,90 8,10 6,15 4,75 3,73 2,96 2,39 1,95
FP 3,95 3,10 2,48 2,01 1,66 1,38 1,16 0,99 0,85
40/4
FV 20,01 14,53 10,80 8,20 6,33 4,97 3,95 3,18 2,59
FP 4,94 3,88 3,10 2,52 2,07 1,73 1,45 1,23 1,06
40/5
FV 25,02 18,16 13,50 10,25 7,92 6,21 4,94 3,98 3,24
FP 5,58 4,38 3,50 2,84 2,34 1,95 1,64 1,40 1,20
45/4
FV 28,50 20,69 15,38 11,67 9,02 7,07 5,63 4,53 3,69
FP 3,33 2,98 2,38 1,94 1,59 1,33 1,12 0,95 0,81
50/2
FV 19,54 14,19 10,55 8,01 6,18 4,85 3,86 3,11 2,53
FP 5,49 4,47 3,58 2,90 2,39 1,99 1,68 1,42 1,22
50/3
FV 29,32 21,28 15,82 12,01 9,28 7,28 5,79 4,66 3,80
FP 7,32 5,96 4,77 3,87 3,19 2,65 2,23 1,90 1,63
50/4
FV 39,09 28,38 21,10 16,01 12,37 9,70 7,72 6,22 5,07
FP 9,15 7,46 5,96 4,84 3,98 3,32 2,79 2,37 2,03
50/5
FV 48,86 35,47 26,37 20,01 15,46 12,13 9,65 7,77 6,33
FP 7,77 7,13 6,07 4,93 4,06 3,38 2,85 2,42 2,07
60/3
FV 47,24 36,78 27,34 20,75 16,03 12,58 10,01 8,06 6,57
FP 10,37 9,50 8,10 6,58 5,41 4,51 3,80 3,23 2,76
60/4
FV 62,99 49,04 36,46 27,67 21,37 16,77 13,34 10,75 8,75
Statics
FP 12,96 11,88 10,12 8,22 6,77 5,64 4,75 4,03 3,46
60/5 and
FV 78,74 61,30 45,57 34,58 26,72 20,96 16,68 13,43 10,94
Load
FP 10,41 9,55 8,81 7,71 6,35 5,29 4,45 3,78 3,24
70/3 Tables
FV 64,30 54,79 42,94 43,42 25,45 19,97 15,89 12,80 10,43
FP 13,88 12,73 11,75 10,28 8,46 7,05 5,93 5,04 4,32
70/4
FV 85,74 73,05 57,90 43,93 33,94 26,63 21,19 17,07 13,90
FP 17,36 15,91 14,69 12,85 10,58 8,81 7,42 6,30 5,40
70/5
FV 107,17 91,32 72,37 54,92 42,42 33,29 26,48 21,33 17,38
FP 17,82 16,33 15,08 14,00 12,41 10,34 8,70 7,39 6,34
80/4
FV 111,98 95,42 82,27 65,14 50,66 39,75 31,63 25,48 20,75
FP 22,27 20,42 18,85 17,50 15,51 12,92 10,88 9,24 7,92
80/5
FV 139,98 119,27 102,84 81,98 63,32 49,69 39,53 31,84 25,94

Legend for conversion values: see page 8/9.

12 LOAD TABLE VEHICULAR GRATING

Vehicular grating, DIN EN 1991, S235 JR+N St 37-2

Width between supports [mm]

Load
200 300 400 500 600 700 800 900 1.000 1.100 1.200 1.300 1.400 1.500
Total load Small van (F2)
Wheel load 10 kN 30/4 30/4 30/4 40/4 40/4 40/5 50/4 50/4 60/4 60/4 60/4 70/4 70/4 70/4
LA 200 x 200 mm
Total load Van 6,0 to
Wheel load 20 kN 30/4 40/5 50/5 60/4 60/5 70/5 70/5 80/5 80/5 90/5 90/5 100/5 100/5 110/5
LA 200 x 200 mm
Total load Van 9,0 to
Wheel load 30 kN 30/5 50/4 60/4 70/4 80/4 80/5 90/5 100/5 100/5 110/5 110/5 120/5 120/5 130/5
LA 200 x 260 mm
Total load Van 12,0 to
Wheel load 40 kN 30/5 50/5 60/5 70/5 80/5 90/5 100/5 110/5 120/5 120/5 130/5 140/5 140/5 150/5
LA 200 x 300 mm
Total load Van 16,0 to /
Heavy truck 30 to
30/5 50/4 60/5 80/5 90/5 100/5 110/5 120/5 130/5 130/5 140/5 150/5 150/5 -
Wheel load 50 kN
LA 200 x 400 mm
Total load Heavy truck 60 to
Wheel load 100 kN 40/4 60/4 70/5 90/5 110/5 130/5 140/5 150/5 - - - - - -
LA 200 x 600 mm
The calculation of the bearing bars for passenger cars is carried out taking into account the vibration coefficient (braking factor) of 1.0 according to DIN EN 1991-1-1:2010-12 +
NA. The calculation of the bearing bars for trucks and heavy trucks is carried out taking into account the vibration coefficient (braking factor) of 1.4 according to DIN 1072 (12.85).

Vehicular grating with forklift truck, pneumatic tyres, DIN EN 1991, S235 JR+N St 37-2

Width between supports [mm]

Load
200 300 400 500 600 700 800 900 1.000 1.100 1.200 1.300 1.400 1.500
Total load 3,1 to
Wheel load 13 kN 30/4 30/5 40/5 50/4 50/5 60/4 60/5 60/5 70/5 70/5 80/4 80/5 80/5 90/5
LA 200 x 200 mm
Total load 4,6 to
Wheel load 20 kN 30/4 40/5 50/5 60/4 60/5 70/5 70/5 80/5 80/5 90/5 90/5 100/5 100/5 110/5
LA 200 x 200 mm
Total load 7 to
Wheel load 31,5 kN 35/5 50/5 60/5 70/5 80/5 90/5 90/5 100/5 110/5 110/5 120/5 120/5 130/5 130/5
LA 200 x 200 mm
Total load 10 to
Wheel load 45 kN 45/5 60/5 70/5 80/5 100/5 100/5 110/5 120/5 130/5 130/5 140/5 150/5 150/5 -
LA 200 x 200 mm
Total load 15 to
Wheel load 70 kN 50/5 70/5 90/5 110/5 120/5 130/5 140/5 150/5 - - - - - -
LA 200 x 200 mm
Total load 19 to
Wheel load 85 kN 60/5 80/5 100/5 120/5 130/5 140/5 150/5 - - - - - - -
LA 200 x 200 mm
The calculation of the bearing bars is carried out taking into account the vibration coefficient (braking factor) of 1.4.

Vehicular grating with forklift truck, solid rubber tyres, DIN EN 1991, S235 JR+N St 37-2

Width between supports [mm]

Load
200 300 400 500 600 700 800 900 1.000 1.100 1.200 1.300 1.400 1.500
Total load 3,1 to
Wheel load 13 kN 30/4 35/5 45/5 50/5 60/5 70/5 70/5 80/5 80/5 90/5 90/5 90/5 100/5 100/5
LA 200 x 200 mm
Total load 4,6 to
Wheel load 20 kN 35/4 45/5 60/5 70/5 80/4 80/5 90/5 100/5 100/5 110/5 110/5 120/5 120/5 130/5
LA 200 x 200 mm
Total load 7 to
Wheel load 31,5 kN 40/5 60/5 70/5 80/5 100/5 100/5 110/5 120/5 130/5 130/5 140/5 150/5 150/5 -
LA 200 x 200 mm
Total load 10 to
Wheel load 45 kN 50/5 70/5 90/5 100/5 110/5 120/5 130/5 140/5 150/5 - - - - -
LA 200 x 200 mm
Total load 15 to
Wheel load 70 kN 60/5 90/5 110/5 130/5 140/5 150/5 - - - - - - - -
LA 200 x 200 mm
Total load 19 to
Wheel load 85 kN 70/5 100/5 120/5 140/5 150/5 - - - - - - - - -
LA 200 x 200 mm

The calculation of the bearing bars is carried out taking into account the vibration coefficient (braking factor) of 1.4.
 13

Vehicular grating, DIN EN 1991, S235 JR+N St 37-2 The table applies to the standard mesh spacing of 33.3 x 33.3
and material S235 JR+N St 37-2.
Width between supports [mm]
Load The values represent the maximum permitted load-bearing ca-
1.600 1.700 1.800 1.900 2.000
pacity of the grating.
Total load Small van (F2)
Wheel load 10 kN 70/5 80/4 80/5 90/5 90/5 LA = load carrying area
LA 200 x 200 mm
Total load Van 6,0 to
Wheel load 20 kN 110/5 110/5 120/5 120/5 130/5 Conversion values:
LA 200 x 200 mm
1 kN ≙ 100 kg
Total load Van 9,0 to
Wheel load 30 kN 130/5 140/5 140/5 150/5 150/5 10 KN ≙ 1 to
LA 200 x 260 mm
10 N ≙1 daN ≙ 1 kp
Total load Van 12,0 to
Wheel load 40 kN 150/5 - - - -
LA 200 x 300 mm
Total load Van 16,0 to / The support length for gratings should correspond to the grating
Heavy truck 30 to height, but at least 30 mm.
Wheel load 50 kN - - - - -
LA 200 x 400 mm
* NOTE: DIN 1072 is no longer valid. However, these load as-
Total load Heavy truck 60 to sumptions are still frequently used for gratings. When using
Wheel load 100 kN - - - - - these load assumptions, it is advisable to consult with the in-
LA 200 x 600 mm
spector and client.
** according to BGI/GUV-I 588-1, page 12

Vehicular grating with forklift truck, pneumatic tyres, DIN EN 1991, S235 JR+N St 37-2

Width between supports [mm]

Load
1.600 1.700 1.800 1.900 2.000

Total load 3,1 to

Wheel load 13 kN 90/5 90/5 100/5 110/5 110/5
LA 200 x 200 mm
Total load 4,6 to
Wheel load 20 kN 110/5 110/5 120/5 120/5 130/5
LA 200 x 200 mm
Total load 7 to
Wheel load 31,5 kN 140/5 140/5 150/5 150/5 150/5
LA 200 x 200 mm
Total load 10 to
Wheel load 45 kN - - - - -
LA 200 x 200 mm
Total load 15 to
Wheel load 70 kN - - - - -
LA 200 x 200 mm
Total load 19 to
Wheel load 85 kN - - - - -
LA 200 x 200 mm

Vehicular grating with forklift truck, solid rubber tyres, DIN EN 1991, S235 JR+N St 37-2

Width between supports [mm]

Load
1.600 1.700 1.800 1.900 2.000

Total load 3,1 to

Wheel load 13 kN 110/5 110/5 110/5 120/5 120/5
LA
Statics
200 x 200 mm
and
Total load 4,6 to
Wheel load 20 kN 130/5 140/5 140/5 140/5 150/5
Load
LA 200 x 200 mm Tables
Total load 7 to
Wheel load 31,5 kN - - - - -
LA 200 x 200 mm
Total load 10 to
Wheel load 45 kN - - - - -
LA 200 x 200 mm
Total load 15 to
Wheel load 70 kN - - - - -
LA 200 x 200 mm
Total load 19 to
Wheel load 85 kN - - - - -
LA 200 x 200 mm
14 STANDARDS AND CERTIFICATES

Q u a l i t y a n d Te s t S p e c i f i c a t i o n
are described in the quality assurance document RAL-

LARGEST SIDE LENGTH S

GZ 638.

These manufacturing and delivery tolerances must be

observed for the production of all grating in accordance
with the following specification of sizes:
- for bearing bars ≤ 60 mm x 5 mm
- mesh spacing max. 68 mm and min. 11 mm D¹ D²
- grating size max. 2.0 m², with a permissible lateral
dimension of at most 2,000 mm.

Diagonal distortion: D1 - D2 0,01 x s

Permitted tolerances for
press locked gratings:
The tolerances occurring under a load (deformations)
are not included.
N

J I
Top protruding edge N max. = 1.0 mm Inclination of the bearing and edge bars I max. = 0.1 x
J, but max. 3 mm

H O

Deviations for convex O max. = 1/200 of the length for

t dimensions > 450 mm; max. 8 mm for dimensions
Oblique section of the bearing bar and cross bar t smaller than 450 mm; max. 3 mm
max. = ± 0.1 x H, but max. 3 mm
P

K
Deviations for concave P max. = 1/200 of the length
for dimensions > 600 mm; max. 8 mm for dimensions
smaller than 600 mm; max. 3 mm

Higher cross bar K max. = 1.5 mm

Q

Deviations for convex Q max. = 1/200 of the width for di-

M mensions > 450 mm; max. 8 mm for dimensions small-
er than 450 mm; max. 3 mm
Bottom protruding edge M max. = 1.0 mm

Deviations for concave R max. = 1/200 of the width

for dimensions > 600 mm; max. 8 mm for dimensions
smaller than 600 mm; max. 3 mm
 15

Permitted tolerances for press

welded grating:
The tolerances occurring under a load (deformations)
are not included.
L

Projecting cross and edge bar L max. = 0.5 mm Inclination of the bearing and/or cross bar t max. = ±
0.1 x H, but max. 3 mm

J I
Deviations for convex O max. = 1/150 of the length for
dimensions > 450 mm; max. 8 mm for dimensions
smaller than 450 mm; max. 3 mm
Inclination of the bearing and edge bars J max. = 0.1 x
I, but max. 3 mm
P

K
Deviations for concave P max. = 1/200 of the length
for dimensions > 600 mm; max. 8 mm for dimensions
smaller than 600 mm; max. 3 mm
Higher cross bar K max. = 1.5 mm

Q
N

Deviations for convex Q max. = 1/150 of the width for

dimensions > 600 mm; max. 8 mm for dimensions
Top protruding edge N max. = 1.0 mm smaller than 450 mm; max. 3 mm

Deviations for concave R max. = 1/200 of the width

Bottom protruding edge M max. = 1.0 mm for dimensions > 600 mm; max. 8 mm for dimensions
smaller than 600 mm; max. 3 mm

Service
/Stan-
dards /
Certi-
fi-cates
 MEISER INTERNATIONAL

Production sites
Germany Egypt Peru
Gebr. MEISER GmbH Hady MEISER Egypt GRATING MEISER LATAM
Edmund Meiser Straße 1 for Bar grating production S.A.E. Calla San Carlos Mz Lote 6
D-66839 Schmelz-Limbach 6, Ramo Buildings/Nasr Road Urb. Santa Marta Ate
Tel +49 (0) 68 87 - 3 09-0 Nasr City, Cairo Lima - Peru
Fax +49 (0) 68 87 - 3 09-3000 Arab Republic of Egypt Tel  +51 (0) 989 26 16 19
E-Mail [email protected] Tel +20 (0) 2 44 69 70 48 Fax +51 (0) 171 86 182
Fax +20 (0) 24 15 14 85 E-mail [email protected]
MEISER Vogtland OHG E-Mail [email protected] www.gratingperu.com
Am Lehmteich 3
D-08606 Oelsnitz France Turkey
Tel +49 (0) 37 421 - 50-0 MEISER Sarl MEISER Izgara San ve Tic Ltd Sti
Fax +49 (0) 37 421 - 50 2120 2101 Route de Béthune Arslanbey OSB Mah. 3. Sok. No: 8
E-Mail [email protected] ZA l’Alouette 41080 Kartepe-Kocaeli
F-62136 LESTREM Tel +90-262-3512051
Belgium François Bernardeau Tel +90-5-444-634737
MEISER FAMECO S.A. Tel +33 321 64 75 43 Fax +90-262-3512041
Rue Pelé-Bois 4 Fax +33 321 64 75 42 E-Mail [email protected]
B-4590 Ouffet E-Mail [email protected]
Tel + 32 (0) 86 36 91 12 UAE
Tel + 32 (0) 86 36 64 33 Hungary Lionweld MEISER LLC
E-Mail [email protected] MEISER Ferroste Kft. DUTCO Compound
Papirgyári ut 13 Jebel Ali Industrial 2
Brazil H-2400 Dunaújváros DUBAI
MARANGONI MEISER Tel +36 (0) 25 511-100 United Arab Emirates
Pisos Metálicos Ltda. +36 (0) 25 511-012 Tel + 971 (0) 48 80 11 25
Avenida João Pinto, 1017 Fax +36 (0) 25 501-870 Fax + 971 (0) 48 80 11 99
Parque da Empresa E-Mail [email protected] E-Mail [email protected]
CEP 13803-360 Mogi Mirim –
SP BRASIL Marocco
Tel + 55 19 38059640 MEISER EGL Sarl
E-Mail [email protected] Zone Industrielle sud ouest -
Lot 118
Mohammedia - Marokko
Tel +212 523 31 29 48
Tel +212 523 31 29 45
E-Mail [email protected]

You will find all our further offices and agencies listed on our website.
www.meiser.de/en/meiser-worldwide 05/2022-online