Popular Mechanics - Saturday Mechanic: Electric Cooling Fan Problems http://hearst.corp.printthis.clickability.com/pt/cpt?action=cpt&title=Popu...

SAVE THIS | EMAIL THIS | Close

Electric Cooling Fan Problems

BY PAUL WEISSLER
Published on: April 1, 1999

It's a really, really warm day, but the temperature gauge reads
normal and the a/c is blowing out a lot of cold air, so who cares?
Then the traffic suddenly slows to a crawl and doesn't get any
better. Gradually the temperature gauge needle creeps toward the
Hot end of the dial, and the air blowing out of the a/c registers is
anything but cold. In fact, to forestall overheating, you shut it off.
Even worse, you soon have to turn on the heat to try to prevent a
boil-over, and open the windows to try to get a breeze.

If you're lucky, the traffic tie-up breaks, and you're cruising again.
The gauge needle starts dropping, and you turn off the heater. Still
sweaty, you turn on the a/c again, and even if the air isn't frigid, it's
cold enough to make you feel better.

Later, you lift the hood with the engine running near an overheat
and the a/c on-the radiator electric fans aren't running. But why?
The fan may be under the complex control of a powertrain
computer, but the basic circuit is pretty straightforward.

On almost all cars the fans should go on if the a/c is turned on,
triggered by the powertrain computer or by an a/c pressure switch.
The fans may not go on instantly, but certainly within a couple of
minutes. If they don't, proceed to a circuit diagnosis.

The simplest first circuit check you can make is the current feed,
starting at the fuse, which on late models is in an underhood fuse Try jumping the battery direct to the fan to see if it
box. Just pull it out and look. Replace it if it's blown. On older spins.
models it's often a fusible link-a short section of wire typically four
gauge numbers higher than the wire of which it's part. You may see
it's singed. Even if it isn't, pull on the ends of the wrap, and if it
stretches, the wire underneath is broken.

Checking The Fan Motors

Fuse okay? The most practical approach is to go next to the end of

1 of 4 29/08/2006 12:21 PM
Popular Mechanics - Saturday Mechanic: Electric Cooling Fan Problems http://hearst.corp.printthis.clickability.com/pt/cpt?action=cpt&title=Popu...

the circuit: the fans themselves. Most cars have two fans. Unplug
one fan's wiring connector and (referring to the wiring diagram
color codes) hot-wire the fan motor's half of the connector. Run
one jumper wire from the current feed terminal of the connector
half to the battery's positive terminal. Attach a second jumper wire
to the other terminal of the connector and run it to an electrical
ground. The fan should run. If it doesn't, the fan motor apparently
is defective.

Some cars have a single fan that runs at two speeds. In these cases,
the connector may have:
Two terminals (one from a dual power feed-through a dropping
resistor for low speed and a resistor-bypass circuit for high
speed-plus the second one for the ground). There's a splice or
connector for the dual power feed earlier in the circuit. If you
check by hot-wiring at the fan motor itself, it will run at high
speed.
Three terminals (one for low-speed feed, one for high-speed and a
common ground). Check each power feed terminal separately,
using the common ground in each case.
Four terminals (high, low and two grounds). Hot-wire each pair
separately with your jumper wires.

Testing Coolant Switch Or Sensor

If both fans run when they're hot-wired, the problem is somewhere
between the current feed at the fuse and the fan motors. On systems
where the trigger for the fans is a coolant temperature switch,
unplug the switch connector. Be sure you have the right one, as
some vehicles have as many as three: one for a dashboard warning
light, one for an overhead console and one for the powertrain
computer.

With the engine running and with the coolant switch unplugged, the
fan should come on because the powertrain computer logs a trouble There may be several temperature sensors and
switches on the engine. Find the correct one and
code for a failed switch and turns on the fans in most systems. If it check it with a test light or an ohmmeter.
doesn't, and the switch is a typical domestic design, it has a
normally open type that stays open until coolant temperatures are
high, when it closes to turn on the fan. To double-check, just ground
the unplugged connector's single wire terminal, using a jumper
wire. The fan should spin. Many Japanese cars have circuits with
normally closed switches. They open with high coolant
temperatures to turn on the fan, so a simple unplugging (with the
ignition on) always should get the fans to operate with this setup.

Most late models have a coolant temperature sensor. It isn't a

switch, but a temperature-sensitive resistor (thermistor) that sends a
signal to the powertrain computer. The computer, which also has
some control over a/c operation, then decides when the fans should

2 of 4 29/08/2006 12:21 PM
Popular Mechanics - Saturday Mechanic: Electric Cooling Fan Problems http://hearst.corp.printthis.clickability.com/pt/cpt?action=cpt&title=Popu...

operate and at what speed. You may not be able to get a response by
simply unplugging the sensor connector or even by grounding it.
Instead, check its calibration by connecting an ohmmeter. The
thermistor develops lower resistance as the temperature goes up,
higher resistance as it drops. If the sensor reads a thousand ohms or
more (which signals low temperature) when the engine coolant is
warmed up, it's out of calibration. Replace it.

Relay Diagnosis You can jump across the fan relay to confirm the
relay's failure.
Head for the fan relay (or relays--some systems have low- and
high-speed fan relays). Turn on the ignition, and locate the relay
terminal for the wire from the switch. When you ground its terminal
with a jumper wire, the relay should click and the fan should run. If
it does, the relay and its circuit to the fans are good. Any problem is
in the wiring between the coolant temperature switch and the relay.

If the fan still won't spin, continue at the relay, which has two
current feeds, one to the electromagnetic coil, one to the electrical
contacts. Probe the two current feed terminals of its wiring
connector with a grounded test light. With the ignition on, it should
go on in both cases. No light in one? There's a break in the wiring
from the fuse to that relay terminal.

On systems with computer control via a sensor signal, make a

similar test of the relay current feed terminals with a grounded test
light and the ignition on.

If the current feeds are good, ground the relay's switch terminal (the
one with the wire that goes to the coolant switch). If there's a sensor
and the switch terminal wire goes to the powertrain computer,
unplug the wire before grounding the terminal. The relay should
click and operate the fans. If it doesn't, replace the relay.

You may have trouble doing this with relays that plug into an
underhood relay "center." Unplug the relay, turn on the ignition and
with your test light probe the two current feed terminals in the relay
center. If they pass (turning on the test light), make up short jumper
wires to connect to the unplugged relay and one long jumper (that
you run to an electrical ground) for the switch terminal. If the relay
still doesn't work (ignition on), replace the relay. If the relay does
click, probe the output terminal to the fan motor with a grounded
test light. Light goes on? The problem is in the wiring from relay to
fan motor.

Your diagnosis may point to the powertrain computer. It's rare, but
a computer failure can be responsible--without a Check Engine light
or trouble code. Perhaps just a single driver has blown, so the
computer itself seems to be performing normally. In addition, in a
number of cars, particularly GM models, the powertrain computer
turns off the fans if the vehicle is cruising 40 to 45 mph or higher.
This strategy relies on the vehicle speed sensor, which may be

3 of 4 29/08/2006 12:21 PM
Popular Mechanics - Saturday Mechanic: Electric Cooling Fan Problems http://hearst.corp.printthis.clickability.com/pt/cpt?action=cpt&title=Popu...

misbehaving. If your speedometer is way off, or not working at all,

it's something to consider if the relay works when grounded. Want
to work through one of these problems? Boot up your PM CD-ROM
or open your factory service manual, plug in a Saturday
Mechanic-level scan tool and go through the trouble-tree
diagnostics to find the answer.

HOW IT WORKS:The Electric Fan

The fan is powered by an electric motor, which is wired to a

relay. The relay is a magnetically controlled switch. It typically
has four terminals, two of which are current feeds from a fused
source of 12-volt electricity. At the relay, there is one current
feed into an electromagnetic coil, and one feed into a set of
contacts for the switch, which is open. The other terminal for
that open switch is connected to the electric motor for the fan.
The fourth terminal, also for the coil, is wired to the powertrain
computer, which may look at various signals to determine
whether or not to provide an electrical ground for that coil. If, as
in this circuit example, it gets a high-temperature signal from the
coolant temperature sensor, also wired to it, the powertrain
computer can choose to ground the coil terminal. This energizes
the coil, creating a magnetic field that pulls the arm on the
power feed contact, so that it touches the terminal for the wire to
the electric motor. That closes the switch of the relay. Current
flows through the closed contacts of this switch to the electric
motor, which spins to operate the fan.

Links referenced within this article

Find this article at:

http://www.popularmechanics.com/home_improvement/how_to_central/electrical/1272431.html

SAVE THIS | EMAIL THIS | Close

Uncheck the box to remove the list of links referenced in the article.

4 of 4 29/08/2006 12:21 PM