@

RX 60-16

RX 60 Technical Data. RX 60-18

RX 60-20
Electric forklift trucks
2 RX 60 TECHNICAL DATA.

This specification sheet to VDI Guideline 2198 only gives the technical figures for the standard truck.
Different tyres, other masts, additional equipment etc. could give different figures.

1.1 Manufacturer STILL STILL STILL

1.2 Manufacturer’s model designation RX 60-16 RX 60-18 RX 60-20
Characteristics

1.3 Power supply - electric, diesel, petrol, gas, mains electric Electric Electric Electric
1.4 Type of control - hand, pedestrian, stand-on, rider seated Rider seated Rider seated Rider seated
1.5 Carrying capacity/load Q kg 1600 1800 2000
1.6 Load centre c mm 500 500 500
1.8 Load distance x mm 355 355 365
1.9 Wheelbase y mm 1448 1448 1448
2.1 Weight kg 3479 3479 3517
2.2 Axle loadings laden front kg 4175 4495 4873
Weights

2.2.1 Axle loadings laden rear kg 904 784 644

2.3 Axle loadings unladen front kg 1615 1615 1659
2.3.1 Axle loadings unladen rear kg 1864 1864 1858
3.1 Tyres - rubber (V), SE, pneu.(L), poly.(PE) SE SE SE
3.2 Tyre size - front 18 x 7-8 200/50-10 200/50-10
Wheels | Chassis

3.3 Tyre size - rear 16 x 6-8 16 x 6-8 16 x 6-8

3.5 Wheels - number front (x = drive wheel) 2x 2x 2x
3.5.1 Wheels - number rear (x = drive wheel) 2 2 2
3.6 Track width - front b10 mm 932 942 942
3.7 Track width - rear b11 mm 865 865 865
4.1 Tilt angle, mast/fork carriage forwards ° 3 3 3
4.1.1 Tilt angle, mast/fork carriage backwards ° 8 8 8
4.2 Closed height h1 mm 2160 2160 2160
4.3 Free lift h2 mm 150 150 150
4.4 Lift height h3 mm 3230 3230 3150
4.5 Height, mast raised h4 mm 3873 3873 3725
4.7 Height to top of overhead guard (cabin) h6 mm 2240 2240 2240
4.8 Seat height h7 mm 1173 1173 1173
4.12 Coupling height h 10 mm 460/350 460/350 460/350
4.19 Overall length l1 mm 2908 2908 2918
Basic dimensions

4.20 Length to front face of forks l2 mm 2061 1983 2092

4.21 Overall width b1 mm 1099 1138 1138
4.22 Fork thickness s mm 40 40 40
4.22.1 Fork width e mm 80 80 80
4.22.2 Fork length l mm 800 800 800
4.23 Fork carriage to DIN 15173 - class/form A or B ISO II/A ISO II/A ISO II/A
4.24 Fork carriage width b3 mm 980 980 980
4.31 Ground clearance beneath mast, laden m1 mm 90 90 90
4.32 Ground clearance at centre of wheelbase m2 mm 123 123 123
4.33 Aisle width for pallets 1000 x 1200 wide A st mm 3439 3439 3449
4.34 Aisle width for pallets 800 x 1200 long A st mm 3638 3638 3648
4.35 Outer turning radius Wa mm 1883 1883 1883
4.36 Inner turning radius b13 mm 538.5 538.5 538.5
5.1 Speed laden km/ h 20 20 20
5.1.1 Speed unladen km/ h 20 20 20
5.2 Lift speed laden m/ s 0.53 0.52 0.45
5.2.1 Lift speed unladen m/ s 0.62 0.62 0.58
5.3 Lowering speed laden m/ s 0.51 0.52 0.53
5.3.1 Lowering speed unladen m/ s 0.47 0.48 0.49
5.5 Rated drawbar pull laden N 2775 2611 2602
Performance data

5.5.1 Rated drawbar pull unladen N 2916 2916 2905

5.6 Max. drawbar pull laden N 9967 9983 9663
5.6.1 Max. drawbar pull unladen N 9789 9789 9785
5.7 Gradeability laden % 11.6 10.7 10.2
5.7.1 Gradeability unladen % 17.0 17.0 16.8
5.8 Max. gradeability laden % 20.2 19.4 18.0
5.8.1 Max. gradeability unladen % 26.0 26.0 26.3
5.9 Acceleration time laden s 4.1 4.3 4.3
5.9.1 Acceleration time unladen s 4.0 4.1 4.2
5.10 Brakes electr. /mech. electr. /mech. electr. /mech.
6.1 Drive motor hourly capacity kW 2x5.5 2x5.5 2x5.5
6.2 Hoist motor capacity at 15% duty factor kW 11 11 11
6.3 Battery equipment to DIN 43531/ 35 / 36 A, B, C, no DIN 43536 A DIN 43536 A DIN 43536 A
E-Motor

6.4 Battery voltage U V 80 80 80

6.4.1 Battery capacity K5 Ah 420LA 420LA 420LA
6.5 Battery weight kg 1238 1238 1238
6.6 Energy consumption 60 VDI work cycles/hour kWh/h 4.4 4.5 4.7
8.1 Drive control
Miscellaneous

8.2 Operating pressure for attachments bar 250 250 250

8.3 Oil flow for attachments l/min 30 30 30
8.4 Average noise peak at operator’s ears dB(A) <70 <70 <70
8.5 Trailer coupling, type/DIN Bolt Bolt Bolt
 Ast

100 100

α β

l6
h4

Seat adjustable
h3

l +
± 90

h6
h1
h7
Q

b12
c

h10

b13
h2

m1

m2
s

x y
l1 R

Wa
e
adjustable
Forks
b10
b1
b3

Dimensions relate
to a vertical mast.

Fork carriage
Hook-on sideshift

Capacities RX 60-16 Tele -/ HiLo mast Capacities RX 60-16 Triplex mast

Load centre c = 500 mm Load centre c = 500 mm

Load centre c = 600 mm

Load centre c = 600 mm
Load centre c = 800 mm
Capacity

Capacity

Load centre c = 800 mm

Rated lift Rated lift

Capacities RX 60-18 Tele -/ HiLo mast Capacities RX 60-18 Triplex mast

Load centre c = 500 mm Load centre c = 500 mm

Load centre c = 600 mm

Load centre c = 600 mm
Load centre c = 800 mm
Capacity

Capacity

Load centre c = 800 mm

Rated lift Rated lift

Capacities RX 60-20 Tele -/ HiLo mast Capacities RX 60-20 Triplex mast

2000 Load centre c = 500 mm Load centre c = 500 mm
2000
1900
1800 1800
Load centre c = 600 mm
1700 Load centre c = 600 mm 1600
Capacity

1600
Capacity

1400 Load centre c = 800 mm

1500
1200
1400 Load centre c = 800 mm
1300 1000
1200 800
900
600
2000 2500 3000 3500 4000 4500 5000 5500 3000 4000 5000 6000 7000 8000
Rated lift Rated lift
 4

Telescopic mast HiLo mast Triplex mast

Rated lift h3 mm 2630 - 4430 4530 - 5430 2775 - 3975 4020 - 5520 5620 - 7870
Closed height h1 mm 1860 - 2760 2810 - 3260 1860 - 2460 1860 - 2360 2460 - 3210
Free lift Form “B” h2/h5 mm 150 150 1230 - 1830 1230 - 1730 1830 - 2580
Free lift Form “A” h2/h5 mm 150 150 1262 - 1862 1262 - 1762 1812 - 2562
Overall height raised Form “B” h4 mm 3280 - 5080 5180 - 6080 3425 - 4625 4670 - 6170 6270 - 8670
Overall height raised Form “A” h4 mm 3273 - 5073 5173 - 6073 3393 - 4593 4638 - 6138 6238 - 8488
RX 60-16

Forward tilt a ° 3
Back tilt b ° 8 6
Fork location centre - centre mm 216 368 445 521 673 760
Greatest width B mm 1099 1188 1099 1099 1188
Overall length L2 mm 2108 2128
Load distance x mm 355 375
(1000 x 1200) 3439 (1000 x 1200) 3459
Working aisle width Ast mm
(1200 x 800) 3638 (1200 x 800) 3658
Tyres v/h 18 x 7 - 8 / 16 x 6 - 8
Track v/h mm 932/865 990/865 932/865 932/865 990/865
Rated lift h3 mm 2630 - 4430 4530 - 5430 2675 - 3875 3870 - 5370 5470 - 7720
Closed height h1 mm 1860 - 2760 2810 - 3260 1860 - 2460 1860 - 2360 2460 - 3210
Free lift Form “B” h2/h5 mm 150 150 1212 - 1812 1212 - 1712 1812 - 2562
Free lift Form “A” h2/h5 mm 150 150 1212 - 1812 1212 - 1712 1812 - 2562
Overall height raised Form “B” h4 mm 3280 - 5080 5180 - 6080 3343 - 4543 4538 - 6038 6138 - 8389
Overall height raised Form “A” h4 mm 3273 - 5073 5173 - 6073 3343 - 4543 4538 - 6038 6138 - 8388
Forward tilt a ° 3
RX 60-18

Back tilt b ° 8 6
Fork location centre - centre mm 216 368 445 521 673 760
Greatest width B mm 1138 1188 1138 1138 1188
Overall length L2 mm 2108 2128
Load distance x mm 355 375
(1000 x 1200) 3439 (1000 x 1200) 3459
Working aisle width Ast mm
(1200 x 800) 3638 (1200 x 800) 3658
Tyres v/h 200/50 - 10 / 16 x 6 - 8
Track v/h mm 942/865 990/865 942/865 942/865 990/865
Rated lift h3 mm 2550 - 4350 4530 - 5330 2670 - 4370 3865 - 5365 5515 - 7915
Closed height h1 mm 1860 - 2760 2810 - 3210 1860 - 2710 1860 - 2360 2410 - 3210
Free lift Form “B” h2/h5 mm 150 150 1230 - 2080 1230 - 1730 1780 - 2580
Free lift Form “A” h2/h5 mm 150 150 1305 - 5155 1305 - 1805 1855 - 2655
Overall height raised Form “B” h4 mm 3200 - 5000 5100 - 5900 3320 - 5020 4530 - 6030 6180 - 8580
Overall height raised Form “A” h4 mm 3273 - 5073 5173 - 5825 3393 - 4693 4455 - 5955 6105 - 8505
Forward tilt a ° 3
RX 60-20

Back tilt b ° 8 6
Fork location centre - centre mm 216 368 445 521 673 760
Greatest width B mm 1138 1188 1138 1138 1188
Overall length L2 mm 2118 2140
Load distance x mm 365 387
(1000 x 1200) 3449 (1000 x 1200) 3471
Working aisle width Ast mm
(1200 x 800) 3648 (1200 x 800) 3670
Tyres v/h 200/50 - 10 / 16 x 6 - 8
Track v/h mm 942/865 990/865 942/865 942/865 990/865

Drive. The STILL controller ensures sensitive driving with optimal utilisation
The two energy efficient and noise optimised three-phase drive units of energy. It also enables the truck to be held on ramps without using
on the RX 60 act on the front wheels. High traction power and driving the maintenance-free multi-disc brakes, for greater safety and driving
dynamics, even on uneven ground or when climbing ramps, ensure a comfort. The power electronics are protected within the counterweight.
high turnround of goods. This provides a steady build-up of power from The heat from the controller is dissipated into the counterweight over
standstill to maximum speed. In addition, the RX 60’s power boost a large area. This arrangement provides very good cooling without
function, whereby a momentary increase in power is provided when additional fans or filters and makes the work pleasantly quiet and
needed, is a particularly useful characteristic when pushing pallets or reliable.
starting on ramps, for example.
The maintenance-free, efficiency-optimised three-phase drive Electrical system.
guarantees a long battery operating life. Thanks to complete enclosure The electrical system on the RX 60 works digitally. The two separate
the whole drive is protected against the ingress of damaging dust and CAN bus systems allow operation without repercussions on the drive
water spray, so that even applications in the worst conditions are no train. This provides breakdown security. At the same time the robust
problem. controller with its two processors provides mutual monitoring for the
In addition to this, thanks to their electrical regenerative braking, the greatest possible safety. Simple retro-fitting of other electrical units is
motors feed back up to 15% of the energy into the battery when the possible through pre-prepared connections.
drive pedal is released, and thus increase the useful time from a
battery charge by up to 1.5 hours. This means that interim battery
charging or even changing is often not necessary.
 5

Mast. Safety.
Depending on the application, the Telescopic, HiLo or Triplex options Electrical braking when the drive pedal is released, and the fully
offer the following: automatic hold-on-ramp feature which works without using the
- Telescopic: an inexpensive mast design suitable for many brakes, plus the mechanical parking and service brake guarantees safe
applications, with full visibility through the mast use at any time. Battery changes on the RX 60 are carried
- HiLo: supplements the telescopic mast with an additional out using a hand pallet truck, low lift pallet truck, forklift truck or hoist.
central full free lift cylinder to allow high stacking under low Along with the considerable saving in time compared with conventional
ceilings - e.g. in containers or lorries. craning of the battery, especially with cab variants, this concept
- Triplex: for use where there are low doorways but high lift heights, for minimizes the risk of crushing and damage of any
utilisation of warehouses right up to the roof. sort that could occur with a heavy swinging battery.

Hydraulic system. Service.

The speed of the pump motor is demand controlled and precise. The maintenance interval of the RX 60 is 1000 hours or 12 months.
It operates only when either the valve levers or steering wheel are These intervals save time and maintenance costs especially in one
moved, thus providing longer usage from a battery charge. The shift operation, where the 1000 hours roughly corresponds to the
sensitive operation of the hydraulics increases working safety by number of annual operating hours and thus the maintenance and the
positioning loads to the nearest millimetre. The hydraulics improve the annual examination can be carried out at the same time.
energy consumption thanks to: Quick diagnosis by laptop computer and good accessibility of all
- The high efficiency of hydraulic pump even at low speeds, maintenance components in conjunction with the quick availability of
(e.g. when steering). Bronze coated backing washers with very good all necessary parts guarantee short service times and a high level of
anti-friction properties seal the gears against the housing thereby availability for the RX 60.
reducing internal losses.
- The replacement of pre-load valves with load retention valves so that,
when tilting unladen for example, the pump does not have to
overcome a high pre-set valve pre-load with a defined hydraulic
pressure. Furthermore the whole hydraulic system has a separate
pressure relief valve.
The priority valve for the steering is directly connected to the pump so
that hydraulic interfaces and hoses are done away with. This ensures
safer, cleaner operation.

Driver’s compartment.
The driver’s work place in the RX 60:
- The large footwell with its inclined floor plate and anti-slip covering
provides quick convenient entry and exit and also a relaxed leg
position when driving.
- The adjustable steering column with its small steering wheel
provides an ergonomic match to the driver and reduces steering
movements.
- The automotive style foot pedal arrangement can, if wished, be
replaced by a double pedal arrangement, to adapt the RX 60 to
whatever the driver is familiar with, for a maximum turnround of
goods.
- The drive direction switch on the valve lever (hoist and lower)
aids untiring concentrated work, even during long shifts, because it
allows convenient changing of the drive direction without
changing grip.
- Thanks to the heated fully graphic display, the time, maintenance
intervals and battery state, for example, are clearly displayed even
when changing from cold to warm areas of use. The whole RX 60 is
subjected to constant on-board diagnosis.
- With 5 selectable drive programs the driver can match the driving
characteristics of the RX 60 to the application situation or to what is
personally preferred at any time. Each program can be precisely
adapted to the application profile in order to achieve optimum
economy and load turnround performance.
- The driver’s compartment of the RX 60 provides a lot of head room
even for tall drivers, and also good all round vision thanks to the large
viewing panels in the roof, very slim overhead guard legs and the high
seating position.
Your contact

STILL GmbH
Berzeliusstraße 10
D-22113 Hamburg
@
Telephone: +49 (0)40/73 39-2000
Telefax: +49 (0)40/73 39-2001
[email protected]
For further information please visit:
RX 60 16 20 0.8 HHe 05/08 TD Subject to technical modifications.

www.still.de/RX60