Scribd
Upload
59 views4 pages

Integrator Using Ic741 Op-Amp: Engr. Faiz Ullah

The objective of the experiment was to study the operation of an integrator circuit using an op-amp and observe the output waveforms for sine and square wave inputs. A practical integrator circuit was assembled using resistors, a capacitor, and an op-amp. For a sine wave input, the output was a cosine wave shifted by 90 degrees, while a square wave input produced a triangular output wave. The experimental and theoretical output voltages were measured and found to match closely with less than 1% error.

Uploaded by

ZAINUL ABIDEEN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
59 views4 pages

Integrator Using Ic741 Op-Amp: Engr. Faiz Ullah

The objective of the experiment was to study the operation of an integrator circuit using an op-amp and observe the output waveforms for sine and square wave inputs. A practical integrator circuit was assembled using resistors, a capacitor, and an op-amp. For a sine wave input, the output was a cosine wave shifted by 90 degrees, while a square wave input produced a triangular output wave. The experimental and theoretical output voltages were measured and found to match closely with less than 1% error.

Uploaded by

ZAINUL ABIDEEN
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

INTEGRATOR USING IC741 OP-AMP

Lab # 09

Fall 2022

CSE-203L CIRCUITS & SYSTEMS-II

Submitted by: Zainul Abideen


Registration No.: 21PWCSE2022
Class Section: C

 “On my honor, as student of University of Engineering and Technology, I have neither given
nor received unauthorized assistance on this academic work.”

Submitted to: 
Engr. Faiz Ullah
(December 19, 2022)

Department of Computer Systems Engineering


University of Engineering and Technology, Peshawar
Objective:- 
To study the operation of the Integrator using op-amp and trace the output wave forms
for sine and square wave inputs. 

Equipment  

1. Oscilloscope  
2. AC Function Generator  
3. Digital Multimeter 

Theory Overview  

Figure 1 

A circuit in which the output voltage is the integration of the input voltage is called an
integrator. 

In the practical integrator shown in Figure 1, to reduce the error voltage at the output,
a resistor RF is connected across the feedback capacitor CF. Thus, RF limits the low-
frequency gain and hence minimizes the variations in the output voltage.  
Integrator has wide applications in  

1. Analog computers used for solving differential equations in simulation


arrangements.  2. A/D Converters.  
3. Signal wave shaping.  
4. Function Generators.  

Components  
1. Resistors: 10kΩ, 22kΩ  
2. Capacitor 0.1µF  
3. Op-amp 741

 Figure 2 

Procedure
1. Connect the components/equipment as shown in the circuit diagram
Figure 2.  2. Switch ON the power supply.  
3. Apply sine wave at the input terminals of the circuit using function Generator. 
4. Connect channel-1 of CRO at the input terminals and channel-2 at the output
terminals. 
5. Observe the output of the circuit on the CRO which is a cosine wave (90o phase
shifted from the  
Sine wave input) and note down the position, the amplitude and the time period of
Vin & Vo. 
6. Now apply the square wave as input signal.  
7. Observe the output of the circuit on the CRO which is a triangular wave and note
down the position,
The amplitude and the time period of Vin & Vo.  
8. Plot the output voltages corresponding to sine and square wave inputs as shown in
the Figure 3 below.
Figure 3

Table

Vin(p-p)  Frequency  V (Theoretical) 


o V (Experimental) 
o %Error

1V  1kHz -0.156 v 0.15 v 0%

2V  1kHz 0.3184 v 0.31 v 0%

1V  2kHz 0.0796 v 0.080 v -0.50%

2V  1.5kHz 0.212 v 0.210 v 0.94 %

2.5V  2.5kHz 0.159 v 0.16 v 0.62%

You might also like