-|Transparent Guide|-

3-Phase Slim Power Controllers

Product Components Insulating Barrier Specifications

SPR3 Series
• Product ×1 • Insulating barrier ×4 It is recommended to use the included interphase barriers for insulation between Model SPR3-1▭ SPR3-2▭ SPR3-3▭ SPR3-4▭
• 11-pin connector ×1 phases and reduce influence from conductive material. Control phase 3-Phase
• Unit: mm, For the detailed drawings, • With the insulating barrier

INSTRUCTION MANUAL
110 VACᜠ 50 / 220 VACᜠ 50 / 380 VACᜠ 50 / 440 VACᜠ 50 /
Rated load voltage
follow the Autonics website. A 60 Hz 60 Hz 60 Hz 60 Hz
Manual Rated load current Rated load current 25 / 35 / 50 / 70 / 100 / 150 A

B
For the detailed information about communication, etc., please refer to the manuals, Display method 3 digit 7segment LED

2.5
and be sure to follow cautions written in the technical descriptions. Indicators
Operation / manual control indicator (green)
Alarm / output / unit (V, A) indicator (red)

3.8
Visit Autonics website to download manuals.
DRW180136AE 55 DC 4 - 20 mA, 1 - 5 VDCᜡ, ON / OFF contact (non-voltage input), pulse
Auto control input
voltage (5 - 12 VDCᜡ)

1.5

C
DAQMaster Manual control input External adjuster (10 kΩ), internal adjuster (output limit)
Digital input (DI) RUN / STOP selectable, AUTO / MAN selectable, RESET

42.5
Thank you for choosing our Autonics product. • DAQMaster is comprehensive device management program. It is available for

40
Alarm output 250 VACᜠ 3 A, 30 VDCᜡ 3 A, 1c resistance load
Read and understand the instruction manual and manual thoroughly before parameter setting, monitoring. RS485 comm. output Modbus RTU method
• Visit Autonics website to download the manual and the program.
using the product. Rated load current 25 / 35 / 50 A: natural cooling
Rated load current A B C Cooling method
For your safety, read and follow the below safety considerations before using. Rated load current 70 / 100 / 150 A: forced air cooling (with cooling fan)
25 / 35 / 50 A 30 28.2 300 Rated load current 25 / 35 / 50 A: ≈ 4.1 kg (≈ 4.9 kg)
For your safety, read and follow the considerations written in the instruction
Ordering Information 70 A 30 28.2 300
Unit weight
(packaged)
Rated load current 70 A: ≈ 4.2 kg (≈ 5 kg)
manual, other manuals and Autonics website. Rated load current 100 / 150 A: ≈ 8.7 kg (≈ 9.7 kg)
100 / 150 A 40.5 50 370
Keep this instruction manual in a place where you can find easily. This is only for reference. Approval ᜢ
The specifications, dimensions, etc. are subject to change without notice for product For selecting the specified model, follow the Autonics website.
improvement. Some models may be discontinued without notice. Control method Phase control Cycle control ON/OFF control

Follow Autonics website for the latest information. SPR 3 - ❶ ❷ ❸ ❹ ❺ Cautions during Installation Normal /
constant current feedback /
Control mode Fixed cycle -
constant voltage feedback /
❶ Rated load voltage ❹ Feedback control High Temperature Caution constant power feedback
Safety Considerations 1: 110 VACᜠ
2: 220 VACᜠ
N: Normal control
F: Normal, feedback control (constant
While supplying power to the load or right after turning off the power of the load, Applied load
Resistance load,
Resistance load
Resistance load,
do not touch the body and heatsink. inductive load inductive load
3: 380 VACᜠ current / constant voltage / constant Failure to follow this instruction may result in a burn due to the high temperature. Output range 0 to 98% 0 to 100% 0 / 100%
• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.
4: 440 VACᜠ power) Normal control: within ± 10% F.S. of rated load voltage
• ᜸ symbol indicates caution due to special circumstances in which hazards may occur.
❷ Rated load current ❺ Fuse ■ Mount space 4-Ø6 Panel
Phase control Constant current feedback control: within ± 3% F.S. of rated load current
output accuracy Constant voltage feedback control: within ± 3% F.S. of rated load voltage
Number: Rated load current (unit: A) N: None
᜸ Warning

100
Failure to follow instructions may result in serious injury or death. • When installing multiple power controllers, Constant power feedback control: within ± 3% F.S. of rated load power
F: Supports fuse
keep space between power controllers for heat
❸ Option output Power supply 100 - 240 VACᜠ ±10% 50 / 60 Hz
01. Fail-safe device must be installed when using the unit with machinery that N: Alarm output radiation.
may cause serious injury or substantial economic loss.(e.g. nuclear power Min. load current 1A
T: A
 larm output + RS485 comm. output Horizontal: ≥ 50 mm, vertical: ≥ 100 mm
control, medical equipment, ships, vehicles, railways, aircraft, combustion Rated load current 25 / 35 / 50 A: ≤ 14 VA
Power
apparatus, safety equipment, crime / disaster prevention devices, etc.) 50 Rated load current 70 A: ≤ 22 VA
consumption
Failure to follow this instruction may result in personal injury, economic loss or fire. Rated load current 100 / 150 A: ≤ 32 VA

100
02. Do not use the unit in the place where flammable / explosive / corrosive gas, Dimensions Insulation
≥ 200 MΩ (500 VDCᜡ megger)
high humidity, direct sunlight, radiant heat, vibration, impact or salinity may resistance
be present. • Unit: mm, For the detailed drawings, follow the Autonics website.
Dielectric strength 2,000 VACᜠ 50 / 60 Hz for 1 min (between input and power terminal)
Failure to follow this instruction may result in explosion or fire. ■ Rated load current 25 / 35 / 50 A Unit Descriptions Output leakage
03. Install on the device panel, and ground to the bolt for grounding separately. ≤ 10 mArms
105 currents
Failure to follow this instruction may result in fire or electric shock. 92.2 261 Noise immunity ±2 kV the square wave noise (pulse width: 1 ㎲) by the noise simulator
04. Do not connect, repair, or inspect the unit while connected to a power source. 68 4-Ø6 203.1
Memory retention ≈ 10 years (when using non-volatile semiconductor memory type)
Failure to follow this instruction may result in fire or electric shock.
6.8

05. Check ‘Connections’ before wiring. 10 0.75mm amplitude at frequency of 5 to 55Hz in each X, Y, Z direction
Vibration
21.8

Failure to follow this instruction may result in fire. R S T

for 2 hours
06. Do not disassemble or modify the unit. Vibration 0.5mm amplitude at frequency of 5 to 55Hz in each X, Y, Z direction for
Failure to follow this instruction may result in fire or electric shock. (malfunction) 10 min
80 14 15 Ambient temp. -10 to 55 ℃, storage: -20 to 80 ℃ (rated at no freezing or condensation)
01
᜸ Caution Failure to follow instructions may result in injury or product damage. Ambient humi. 35 to 85%RH, storage: 35 to 85%RH (rated at no freezing or condensation)
243.6

80
227

200

09

01. Use the unit within the rated specifications. 02

Failure to follow this instruction may result in fire or product damage. 03
05
04 RS485 Communication Interface
02. Use a dry cloth to clean the unit, and do not use water or organic solvent. 06
Failure to follow this instruction may result in fire or electric shock. 07 Communication protocol Modbus RTU
03. Keep the product away from metal chip, dust, and wire residue which flow 08
into the unit.
■ Rated load current 70 A Connection RS485
Application standard Compliance with EIA RS485
Failure to follow this instruction may result in fire or product damage. 105
Max. connections 31 units (address: 01 to 99)
04. Since leakage current still flows right after turning off the power or in the 92.2 261 09
68 4-Ø6 203.1 Synchronous method Asynchronous
output OFF status, do not touch the load terminal.
Communication method Two-wire half duplex
6.8

Failure to follow this instruction may result in electric shock. 13

11 Communication distance Max. 800 m
21.8

Communication speed 2400, 4800, 9600, 19200, 38400 bps

12 13
Cautions during Use U V W
Communication response time 5 to 99 ms (default: 20 ms)
Start bit 1-bit (fixed)
80
01. Bracket [except rated load current 100 / 150 A model] Data bit 8-bit (fixed)
• Follow instructions in ‘Cautions during Use’. 02. Indicator
Otherwise, it may cause unexpected accidents. 80 Parity bit None, Even, Odd
200
266.6
250

• Use the product, after 3 sec of supplying power. Indicator Function Stop bit 1-bit, 2-bit
• Before use, set the mode and function according to the specification. Especially, RUN Operation indicator (green) Turns on in the RUN mode.
be cautious that the product does not operate when OUT ADJ. is set to 0%. Since Turns on when adjusting load output in
MAN Manual control indicator (green)
changing the mode / parameter during operation may result in malfunction, set the
Load Output Formula
the manual control mode.
mode and function after disconnecting load output. ALM Alarm indicator (red) Flashes in alarming status.
25

• Re-supply the power to the unit after the unit is discharged completely. Failure to OUT Output indicator (red) Turns on when load control outputs.
follow this instruction may result in malfunction. Type Input Formula
• To ensure the reliability of the product, install the product on the panel or metal ■ Rated load current 100 / 150 A 03. Display part Current DC 4 - 20 mA Load output [%]
surface vertically to the ground. 170 RUN mode: Displays depending the front display setting Auto
158 326.5 Voltage 1 - 5 VDCᜡ = Control input [%] × output slope [%]
• Install the unit in the well ventilated place. Setting mode: Displays parameter and setting value (AUTO)
• While supplying power to the load or right after turning off the power of the load, do 140 4 - Ø 6.5 233.2
04. Unit indicator (V, A) 07. Output limit adjuster (OUT ADJ) RS485 communication Load output [%] = RS485 [%]
not touch the body and heat sink. Failure to follow this instruction may result in a burn Dependent on the display setting. Limits output from 0 to 100%. Internal adjuster Load output [%] = internal adjuster [%]
due to the high temperature. 08. Control input /
30

• Install a power switch or circuit breaker in the easily accessible place for supplying or Display setting V A Manual Output External adjuster Load output [%] = external adjuster [%]
Resistance and input OFF OFF comm. output terminal (MAN) limit
disconnecting the power. Internal / external Load output [%]
(11-pin connector terminal)
• Do not wire to terminals which are not used. Voltage ON OFF adjuster = internal adjuster [%] × External adjuster [%]
• Since inter element can be damaged when using with coil load, inductive load, etc., 09. Terminal protection cover
80 Current OFF ON
the inrush current must be under the rated load current. 10. R, S, T load input terminal
Power ON ON 11. Alarm output / power input terminal
• Do not use near the equipment which generates strong magnetic force or high 80
270
210

frequency noise. 05. [MODE] key 12. U, V, W load output terminal

• This unit may be used in the following environments. Enters parameter group, returns to RUN 13. Cooling fan
- Indoors (in the environment condition rated in ‘Specifications’) mode, moves parameters, and saves the [Rated load current 70 / 100 / 150 A model]
- Altitude max. 2,000 m setting value. 14. Heatsink
- Pollution degree 2 06. [◀], [▼], [▲] key Rated load current 100 / 150 A models have
- Installation category III Enters SV setting mode and move digits. left / right mounting holes.
15. Bolt for grounding (M4)
25
-|Transparent Guide|-

Connections Alarm ■ Parameter 1 group Replacement of Fuse

Parameter Display Default Setting range
• Terminal configuration by model may differ depending on the supported spec. • Supported alarms are different depending on the model. P1-1 SOFT START time ■ Case removal
• When several alarms occur at same time, the highest priority error is displayed based
S-T 3

■C
 ontrol input / comm. ■ Load input / output terminal P1-2 SOFT UP time U-T 3 0 to 100 sec
on priority.
output terminal
P1-3 SOFT DOWN time D-T 3
Output low-limit
(11-pin connector) Operation P1-4
value
L-L 0
Priority Type Display Alarm release Model 0 ≤ L-L ≤ H-L ≤ 100 %
①
Alarm Output Output high-limit
P1-5
Noise filter01) 1 SCR error Feedback control value
H-L 100

②
SCR
VR • Error 0 to 100%
Over • Re-supply
Rapid 2 Feedback control • In case of auto control (AUTO), set the output
③ current
O-C display power. P1-6 Output slope
01)

fuse slop limit proportional to control input for limit

SLP 100
flashes. • RESET input
1 - 5 4 - 20 mA Heatsink Output Normal /
④ CAP01) load power.
4 • Alarm
ON/OFF VDCᜡ over heat stops. • Switch to stop Feedback control
TEM
indicator
⑤ S Over (SCR OFF) (STOP) mode. ■ Parameter 2 group
R T 5 (ALM) Feedback control
voltage
⑥
O-V
flashes. Parameter Display Default Setting range
Fuse • Alarm Automatically Normal / 420: DC 4 - 20 mA
RUN / STOP 3
⑦ break output cleared when Feedback control 1-5: 1 - 5 VDCᜡ
FUS
Case fixed bolt
AUTO / MAN turns ON returning within
⑧
Heater Normal P2-1 Control input 512: 5 - 12 VDCᜡ
01)
6 the setting range Feedback control ■ Replacement of fuse
INT 420
break operation ONF: ON / OFF contact
U V W
H-B
RESET
⑨
COM: RS485 communication
• SCR error alarm • Fuse none model is not equipped with a rapid fuse inside. Install the suitable fuse for
*[Feedback control model]
⑩
A (+) LOAD LOAD Even though output is 0%, if the current of 10% or more of the rated load current flows for
over 3 sec continuously, SCR error alarm occurs. Set Control method rated load current of the model separately.
RS485
B (-)
⑪ LOAD
01) When connecting noise filter and
• Over current alarm
This function protects the load from over current. If the current flows over the P2-7 over
PA
V-F*
Normal
Constant voltage feedback
• The performance of the product is guaranteed only when using the fuse provided by
Phase us. For replacing the fuse, use the recommended fuse.
■A
 larm output / power input capacitor, it is appropriate for EMC. current alarm value and P2-8 over current alarm delay time, over current alarm occurs. P2-2 Control method C-F* control Constant current feedback
• Heatsink over heat alarm
C-M PA
[CAP]
terminal Rated load voltage 110 / 220 VACᜠ When the temperature of a heatsink is over 85 ℃, heatsink over heat alarm occurs.
W-F* Constant power feedback Rated load
current
Rec. fuse Manufacturer
Cycle
Alarm Output : 1 μF / 250 VACᜠ • Over voltage alarm F-C
control
Fixed cycle
This function protects the load from over voltage. If the current flows over the P2-9 over 25 A 50FE
(250 VACᜠ 3 A 1c) 100 - 240 VACᜠ Rated load voltage 380 / 440 VACᜠ ONF ON / OFF control
(30 VDCᜡ 3 A 1c) voltage alarm value and P2-10 over voltage alarm delay time, over voltage alarm occurs.
Resistive Load
50 / 60 Hz : 0.47 μF / 500 VACᜠ 35 A 63ET
• Fuse break alarm Manual control (MAN) I_R: Internal adjuster BUSSMANN
Fuse 50 A 80ET
When breaking fuse, not suppling load power, breaking load (single load), fuse brake alarm P2-3 output limit method E_R: External adjuster
N.C. COM N.O. N L
70 A 100FE
MAN I_R
occurs. In the case of normal control model, real-time fuse break alarm is not available during
01)
E_I: Internal / external adjuster
1 2 3 4 5 output, and fuse break alarm operates at 0% output such as RESET. P2-4 Input correction
01)
100 A 660GH-160
• Heater break alarm HINODE
INB )0
Input slope correction -99 to 99% Fuse 150 A 660GH-200
Comparing the full load resistance value and the current load resistance value, if the current P2-5 01)
fixed
SPN )0

Cautions during Wiring

load resistivity is maintained under the P2-12 heater break alarm value for over 3 sec
*[Feedback control model] bolt
continuously, heater break alarm occurs. This alarm operates when control output is over
IN: Resistance and input
10% and load current is over 10% of the rated current. Output does not stop and operates ■ Bolt specification
■ Control input / comm. output terminal (11-pin connector) normally. U-V*: U-V line load voltage
Full load resistance value × 100 V-W*: V-W line load voltage
• Unit: mm, Use penhole terminals of size specified below. Current load resistance (%) = P2-6 Front display W-U*: W-U line load voltage Rated load current Case fixed bolt Fuse fixed bolt
Current load resistance value
DIS IN
U-A*: U-phase load current 25 / 35 / 50 / 70 A M3 M6
6 to 7 V-A*: V-phase load current Top: M8
W-A*: W-phase load current 100 A M4
Bottom: M6
Mode Setting L-W*: Load power
150 A M4 M8
Over current alarm [Feedback control model]
P2-7
value 0 to 120%
OCV 120

≤ 3.5 [MODE] → Monitoring group [MODE] 3 sec → Over current alarm [Feedback control model]
P2-8
delay time 0 to 100 sec
Derating Curve
OCT 5
≤ 1.5
[MODE] 2 sec → Parameter 1 group [MODE] 3 sec → Over voltage alarm [Feedback control model]
P2-9
value
■ Rated load current 25 A ■ Rated load current 35 A
0 to 120%
■ Alarm output / power input & R, S, U load output terminal
OVV 120

Over voltage alarm [Feedback control model]

[MODE] 4 sec → Parameter 2 group [MODE] 3 sec → P2-10
delay time 0 to 100 sec
• Unit: mm, Use crimp terminals of size specified below.
OVT 5

Load current [A]

Load current [A]

[Feedback control model] 25 35
Rated load Alarm output / Load input / RUN [◀ + ▲ + ▼] 5 sec → Parameter reset [MODE] → RUN OFF, ON
Spec. Load resistance value • It executes 100% control output for 3 sec
20 28
current power input output P2-11
6 - 9 terminal auto recognition and the load resistance value recognized 15 21
→ RUN / STOP →
F-L OFF
25 / 35 / 50 / a ≥ 3.0 ≥ 6.0 Auto
external contact automatically as the initial set when the
10 14
70 A b ≤ 6.0 ≤ 16.0 function is ON.
a 7 - 9 terminal Auto / Manual
b → Auto → Heater break alarm [Feedback control model] 5 7
a ≥ 3.0 ≥ 8.0 external contact P2-12
100 / 150 A control value
HBV 10
10 to 100%, OFF 0 0
b ≤ 6.0 ≤ 26.0 0 10 20 30 40 50 55 60 70 0 10 20 30 35 40 50 55 60 70
[▲ + ▼] 2 sec or [RS485 communication output model]
→ Reset 01)
Auto → P2-13 Comm. address Ambient temp.[℃] Ambient temp.[℃]
8 - 9 terminal 01 to 99
ADR 01
• Cable / screw / tightening torque spec. is different depending on the load current. Be
P2-14 Comm. speed
[RS485 communication output model] ■ Rated load current 50 A ■ Rated load current 70 A
sure to the below before connection. 01) In the event of system anomalies and alarms, RESET input restarts the power controller. (parameters are not
BPS 96
24, 48, 96, 192, 384 bps (× 100)
reset.) [RS485 communication output model]
P2-15 Comm. parity bit

Load current [A]

Load current [A]

Rated load Alarm output / NON, EVE, ODD 50 70
Spec. Load input / output
PRT NON
current power input [RS485 communication output model]
P2-16 Comm. stop bit 40 56
Cable AWG 18 to 14 AWG 13 to 4 Parameter Setting 1, 2 bit
STP 2
30 42
Screw M3 M6 [RS485 communication output model]
P2-17 Comm. response time
25 / 35 / 50 / 70 A 5 to 99 ms 20 28
• Some parameters are activated / deactivated depending on the model or setting of
RwT 20
Tightening [RS485 communication output model]
0.5 N m 5.5 to 6.0 N m other parameters. Refer to the description of each parameter. P2-18 Comm. write 10 14
torque EN.A: Enable, DS.A: Disable
• If any key is not entered for 30 sec in each parameter, it returns to RUN mode.
CmW EnA
0 0
Cable AWG 18 to 14 AWG 4 to 2 / 0 OFF 0 10 20 25 30 40 50 55 60 70 0 10 20 30 35 40 50 55 60 70
• [MODE] key: Saves current setting value and moves to the next parameter. P2-19 Lock LC1: Locks parameter 1 group
Screw M3 M8 Ambient temp.[℃] Ambient temp.[℃]
[◀] key: Changes setting digits.
LOC OFF
100 / 150 A LC2: Locks parameter 2 group
Tightening
0.5 N m 6.5 to 7.0 N m
[▲], [▼] key: Changes setting values. P2-20 Parameter reset NO, YES ■ Rated load current 100 A ■ Rated load current 150 A
torque
INI NO

■ Monitoring group
01) Set the below parameters available depends on the control input.

Load current [A]

Load current [A]

Input Input slope Output Monitoring 100 150
Type Control input Display
Parameter Display Display range correction correction slope value
80 120
M1-1 Monitoring value IN 0 to 100% Current DC 4 - 20 mA 420 ○ ○ ○
60 90
M1-2 U-V line load voltage value Voltage 1 - 5 VDCᜡ 1-5 ○ ○ ○
[Feedback control model]
U-V
Auto 40 60
M1-3 V-W line load voltage value Pulse
V-W
0 to rated voltage range, V control
voltage
5 - 12 VDCᜡ INT 512 × × ○
M1-4 W-U line load voltage value W-U (AUTO) The last 20 30
No-voltage ON / OFF contact ONF × × ○
M1-5 U-phase load current value control 0 0
[Feedback control model] input value 0 10 20 30 35 40 50 55 60 70 0 10 20 25 30 40 50 55 60 70
U-A
RS485 communication COM × × ×
M1-6 V-phase load current value Ambient temp.[℃] Ambient temp.[℃]
V-A
0 to rated current range, A Internal adjuster I_R
0 to 100%
M1-7 W-phase load current value
Manual
W-A
[Feedback control model] Output External adjuster E_R
control MAN × × ×
M1-8 Load power value limit
L-W
0 to rated Power range, kW (MAN) Internal /
E_I
external adjuster
[Feedback control model]
0 to 100%
M1-9 Resistance value percentage L-R • Displays the present resistance as percentage
compared to the set resistance of full load auto
recognition.
M1-10 Heatsink temp. TMP 0 to 100 ℃
M1-11 Power supply frequency FRQ 50, 60 Hz

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

www.autonics.com | +82-51-519-3232 | [email protected]