GXI-3000 Preset Dimming Controls

3691017b 1 08.12.16

GXI-3000 Control Unit

Description Cover (shown open)

• Provides pushbutton recall of four

preset lighting scenes, plus Off.
• Allows setup of lighting scenes
using buttons on the Control Unit.
• Controls virtually any light source
(LED, incandescant, etc.) without
an interface.
• Provides lockout options to
prevent accidental changes.
• Includes built-in infrared receiver
for operation with an optional
remote control.
Models available to:
• Accept 230 V~ (CE) input power.
• Control four zones of lighting.
Base Zone Infrared Receiver Scene Selection
GXI-3100 Control Unit allows Buttons
setup of lighting scenes using
buttons on the Control Unit.
GXI-3000 Control Unit
GXI-3500 Control Unit allows
setup of lighting scenes using a
PC, including setting lighting
levels in 1% increments.

S pecificat ion Sub mitt al Page 1

Job Name: Model Numbers:

Job Number:
 GXI-3000 Preset Dimming Controls
3691017b 2 08.12.16

Specifications

Input Power • Provides air gap isolation when the Off scene is
• 230 V~ (CE) 50 Hz selected.
• Lightning Strike Protection: • 10-year power failure memory automatically restores
Can withstand voltage surges of up to 6000 V~ lighting to levels prior to power
and current surges up to 3000 A. interruption.
• Faceplate snaps on with no visible means of
Sources attachment.
Controls the following lighting sources with a
System Communications and Capacities
smooth, continuous Square Law dimming curve
or on a full conduction non-dim basis: • Low-voltage type PELV wiring connects Control
• LEDs Units, Wallstations, and Control Interfaces.
• Incandescent • Up to 8 Control Units may be linked to control up to
• Electronic Low Voltage 32 zones.
• Magnetic Low Voltage • Up to 16 total Wallstations and Control Interfaces
• Fluorescent may be added for a total of 24 control points.
• Neon and Cold Cathode Environment
Load Types • 0-40°C. Relative humidity less than 90%
• Leading/Trailing-edge dimming non-condensing.
• 0-10 V-
• DALIR (broadcast only)
• Switching (non-dimming)
Preset Controls
• 4 preset lighting scenes and off are accessible from
the Control Unit front panel.
• 12 additional scenes are stored in the Control Unit.
These scenes are accessible via Wallstations and/or
Control Interfaces.
• Light levels fade smoothly between scenes. Fade
time can be set differently for each scene, between
0-59 sec. or 1-60 min. Fade time from Off is capped
at 5 sec.
Key Design Features
• Meets IEC 801-2. Tested to withstand 15 kV
electrostatic discharge without damage or
memory loss.
• Provides over-current and short-circuit
protection.
• Provides capability to trim High End and Low End.
• Manual or automatic selection between
leading edge or trailing edge dimming for low
voltage transformers.

S pecificat ion Sub mitt al Page 2

Job Name: Model Numbers:

Job Number:
 GXI-3000 Preset Dimming Controls
3691017b 3 08.12.16

How to Build a Model Number

GXI-3104-T-CE-WH Cover Options Color Options

Opaque A Architectural Matte Finishes
Prefix Cover and Base will match. Standard – Ship in 48 hours
Cover Option: A or T
Translucent Black T
Set-Up White WH
Method Color Black Cover and choice of Ivory IV
Option base color. Beige BE
Number Input Gray GR
Also available: Brown BR
of Zones Voltage
- Custom controls Black BL
Cover - Color matching Designer Gloss Finishes
Option - Engraving Ship in 4 to 6 weeks
Prefix: These options ship in 4 to 6 Cover Option: A only
weeks White GWH
GXI for GRAFIK Integrale 3000 Series Light Almond GLA
Control Units Almond GAL
Ivory GIV
Set-Up Method:
Satin Color Matte Finishes
1 for standard setup via front panel Cover Option: A or T
5 for PC setup Hot HT
Ochre OC
Number of Zones: Terracotta TC
4 Desert Stone DS
Stone ST
Cover Option: Limestone LS
Blue Mist BT
A for Opaque Midnight MN
T for Translucent Black Taupe TP
Biscuit BI
Input Voltage Eggshell ES
CE for 230 V~ (CE) Snow SW
Architectural Metal Finishes
Color Option: Cover Option: T only
See Color Options list Bright Brass BB
Bright Chrome BC
Satin Brass SB
Model Number Satin Chrome SC
Satin Nickel SN
230 V~ (CE) Input Power Antique Brass QB
Antique Bronze QZ
Zone Capacity Bright Nickel BN
Number of Unit Dimmed/ Low-voltage Anodized Aluminum Finishes
Model Number Cover Option: T only
Zones Capacity Switched control
Clear CLA
Live OUtput output Black BLA
Up to 20 LED Brass BRA
4 GXI-3104-_-CE-__ 2300 W/VA 800 W/VA
Drivers / Ballasts Bronze BZA
Up to 20 LED
4 GXI-3504-_-CE-__ 2300 W/VA 800 W/VA
Drivers / Ballasts

S pecificat ion Sub mitt al Page 3

Job Name: Model Numbers:

Job Number:
 GXI-3000 Preset Dimming Controls
3691017b 4 08.12.16

Dimensions and Mounting

Dimensions shown as: in (mm)

3 (76)
8 (200) 8 (208)

5 (138)

4 (95)

3 (84)

9 (227)

Side View Backbox Front Views

0.3 (8) Lutron P/N 241-400

2 (49)

4.5 (116) 3 (73)

Lutron P/N 241-691 (old-work backbox)

S pecificat ion Sub mitt al Page 4

Job Name: Model Numbers:

Job Number:
 GXI-3000 Preset Dimming Controls
3691017b 5 08.12.16

230 V~ (CE) Mains Voltage Wiring

Pull power wiring from distribution panel and to light fixtures. Each Consult Lutron for:
line voltage terminal can accept up to two 12 AWG (2.5 mm2) wires. • Non-dim relay wiring.
For phase-to-neutral wiring, connect one phase to Live and the other • Load side emergency transfer
phase to Neutral. When wired phase-to-phase, the air gap does not wiring.
break both phases while the Control Unit is Off: the MCB(s) must
be turned off when servicing the Control Unit or associated loads.

Load 1
Hot/Live
Hot/Live
Distribution Panel Neutral
Neutral
Load 2
Earth/ D
Ground D 0-10Ballast Control Outputs
V- / DALIR control outputs DL/SL1
DL/SL2
DL/SL3 (2) 2.5 mm2
Hot/Live
Zone 1

Zone 2

Zone 3

Zone 4
DL/SL 4

Neutral (2) PELV ONLY

}
}

}
}
2.5 mm2 1 2 3 4 - + - + - + - +

Load 3

Rear View of GXI-3104 Control Unit

0-10 V- and DALIR control Wiring (2) 2.5 mm2
(2) 1.0 mm2
+
-
Load 4 - Driver

Low-Voltage PELV Wiring

• System communications use low-voltage PELV (Class 2) wiring.
• Wiring must be daisy-chained.
• Wiring must run separately from line (mains) voltage.

PELV (Class 2) wiring link requires:

Two 12 AWG (2.5 mm2) conductors for control power.
One twisted, shielded pair of 18 AWG (0.75 mm2) for data link.

Total length of Control Link may be up to 2000 ft (610 m).

Approved low-voltage cable is available from Lutron1, Belden, and Liberty.
These are approved with 22 AWG (0.25 mm2) data link wires.

Control Interface
Control Unit Wallstations Power
Supply

External 12 V- Power Supply is

required to power more than three
1 GRX-CBL-346S PELV (Class 2) wiring cable is available from Lutron and contains: Wallstations and/or Control Interfaces
- Two 12 AWG (2.5 mm2) conductors for control power. from a single Control Unit.
- One twisted, shielded pair of 22 AWG (0.25 mm2) for data link.

S pecificat ion Sub mitt al Page 5

Job Name: Model Numbers:

Job Number:
 GXI-3000 Preset Dimming Controls
3691017b 6 08.12.16

PELV Terminal Connections

• Each PELV terminal accepts up to two 1.0 mm2 wires.

• Daisy chain the terminal 1, 3, and 4 connections to all Control
Units, Wallstations, and Control Interfaces.
Hot/Live
Neutral

• Each Control Unit has its own power supply. Terminate the
Ballast Control Outputs DL/SL 1
DL/SL 2
DL/SL 3

Zone 1

Zone 2

Zone 3

Zone 4
DL/SL 4

terminal 2 connection (12 V- power) so that each1 2 3 4Control PELV ONLY

Neutral
Neutral

}
}

}
}
1 2 3 4 + - + - + - + -

Unit supplies power to a maximum of three Wallstations. Each

Wallstation should receive power from only one Control Unit.
• Make all connections in the Control Unit’s wallbox. Remote
connections must be in a switchbox or junction box with
a maximum wire length of 8 ft (2.5 m) from the link to the
connected unit.
• Do not allow PELV wires to contact line/mains wires.

Rear View of GXI-3000 Control Unit

Rear View of GXI-3000 Control Unit a3

PELV ONLY
1 2 3 4

a1
PELV ONLY
1 2 3 4
5
Lutron Cable,
GRX-CBL-346S
4
3
2
1

A3 powers Wallstations
A2 and A3
have their own
2, 3, and 4 – no terminal 6
No. 2 connection
power supplies –
between Wallstations
no terminal No. 2 2
1 connection
4 and 5 4
3
4 2
1
4 3
3 2
2 4
1
1
7
3
4 2
3 1
2
1

A1 powers 1 only – 3
4
terminal No. 2 connection 4
3
2

terminates at Wallstation 1 3 1

2
4
1
3
2

A4 powers Wallstations
1

5, 6, and 7 – no terminal
4 No. 2 connection between
4 3 2 1
4
Wallstations 4 and 5
PELV ONLY
3
a2 2
1
4
3
2
1

Rear View of GXI-3000 Control Unit

4 3 2 1
PELV ONLY
Note: A4
• Up to 8 GXI-3000 Series Control Units and 16 Wallstations/Control Interfaces may be
daisy-chained together in one system.
Rear View of GXI-3000 Control Unit
• PELV/Class 2 cable is available from Lutron - order GRX-CBL-346S.

S pecificat ion Sub mitt al Page 6

Job Name: Model Numbers:

Job Number: