Automotive Relays

PCB Double Relays

Double Micro Relay K (THT – THR)

n Small power relay

n Limiting continuous current 30A
n Minimal weight
n Low noise operation
n Wave (THT) and reflow (THR/pin-in-paste) solderable versions
n For single version refer to Single Micro Relay K

Typical applications
Car alarm, door control, door lock, hazard warning signal, heated front/rear
screen, immobilizer, lamps front/rear/fog light, interior lights, seat control,
sun roof, turn signal, window lifter, wiper control.

086C/R2_fcw1b

Contact Data
Contact arrangement 2 form C, 2 CO Contact Data (continued)
Rated voltage 10/12VDC Mechanical endurance > 5x106 ops.
Rated current, form A/form B NO/NC 1) The values apply to a resistive or inductive load with suitable spark suppression and at
30A/25A maximum 13.5VDC for 12VDC load voltages.For a load current duration of maximum 3s
for a make/break ratio of 1:10.
Limiting continuous current, form A/form B
2) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
23°C 30/25A http://relays.te.com/appnotes/
85°C 20/15A 3) Measured at nominal voltage without coil suppression unit. A low resistive suppression
Limiting making current 40A1) device in parallel to the relay coil increases the release time and reduces the lifetime
Limiting breaking current 30A caused by increased erosion and/or higher risk of contact tack welding
Contact material AgSnO2
Min. recommended contact load 1A at 5VDC2)
Initial voltage drop at 10A, typ./max. 30/300 mV Coil Data
Operate/release time typ. 3/1.5ms3) Rated coil voltage 12VDC
Electrical endurance
-40°C, +25°C, +85°C and 14 VDC, Coil versions, DC coil
form C (CO), cyclic temperature Coil Rated Operate Release Coil Rated coil
motor reverse blocked, 25A, 0.77mH >1x105 ops. code voltage voltage voltage resistance power
wiper 25A make/5A break, VDC VDC VDC Ω±10% mW
generator peak -20A on NC, L=1.0mH >1x106 ops. 001 12 6.9 1.5 254 567
form A contact (NO), cyclic temperature 002 10 5.7 1.25 181 552
resistive 20A >3x105 ops. All figures are given for coil without pre-energization, at ambient temperature +23°C.

Coil operating range

300

Max. DC load breaking capacity

250 Umax

200

150

100

50 Uop (E=0V)

0
-40 -20 0 20 40 60 80 100 120
Ambient temperature in °C

Does not take into account the temperature rise due to the contact current
E = pre-energization

Insulation Data
Initial dielectric strength
Load limit curve I: safe shutdown, arc extinguishes during transit time.
between open contacts 500VACrms
Load limit curve II: safe shutdown, no stationary arc.
between contact and coil 500VACrms
Load limit curves measured with low inductive resistors verified for 1000 switching events.

1
09-2011, Rev. 0911 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company. http://relays.te.com/definitions
 Automotive Relays
PCB Double Relays

Double
Micro Relay K (THT – THR) (Continued)

Terminal Assignment
Other Data Bottom view on solder pins
EU RoHS/ELV compliance compliant
Ambient temperature -40 to +105°C 2 form C, 2 CO
Cold storage, IEC 60068-2-1 1000h; -40°C 13 14
Dry heat, IEC 60068-2-2 1000h; +125°C 22
Climatic cycling with condensation, 15 11
EN ISO 6988 20 cycles, storage 8/16 h
Temperature cycling (shock),
21 25
IEC 60068-2-14, Na 100 cycles; -40/+125°C
Temperature cycling, 12
IEC 60068-2-14, Nb 35 cycles; -40/+125°C 24 23
Damp heat cyclic, 86dtw_ab
IEC 60068-2-30, Db, Variant 1 6 cycles 25°C/55°C/93%RH
Damp heat constant,
IEC 60068-2-3 method Ca 56 days 40°C/95%RH
Degree of protection Dimensions
THT: RT III (61810), IP67 (IEC 60529) Double Micro Relay THT
THR: RT II (61810), IP56 (IEC 60529)
Corrosive gas, IEC 60068-2-17: THT Qc, method 2, 1min, 70°C
IEC 60068-2-42 10 days 23,6 ±0,2
IEC 60068-2-43 10 days 6,2 ±0,1
Vibration resistance (functional) 2,5 ±0,2
IEC 60068-2-6 (sine sweep) 10 to 500Hz; 6g6)
0,6 ±0,2
Shock resistance (functional)
IEC 60068-2-27 (half sine) 6ms, up to 30g6)
Terminal type PCB:THT, THR
Weight approx. 8g (0.28oz)

7,65 ±0,2
Solderability (aging 3: 4h/155°C) THT,

9,9 ±0,2
0,4 ±0,1

IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C

Resistance to soldering heat THT,
IEC 60068-2-20 Tb, method 1A, hot dip 10s, 260°C,
with thermal screen
Resistance to soldering heat THR,
IEC 60068-2-58 260°C; preheating min 130°C

2,8 ±0,2 *)
A

Storage conditions according IEC 600688 7)

12,9 ±0,3
Packaging unit 990 pcs.
6) Depending on mounting position: no change in the switching state >10μs. 0,95 ±0,2
7) For general storage and processing recommendations please refer to our Application
Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/

*) Additional tin tops

max. 1 mm
86dtw_se

View of the Terminals

Bottom view on solder pins

8,5
6x
0 ,05

7,5 5,87 0,15

0
1,2 +

C 0,5 3,7 0,25

B 3,4 0,25 0,97 0,15
1,72
4,5 0,25 0,97 0,15
0,06

13 14 22 13 14 22
0,15
3,6
4x

0,25
0,25
6,66
1,37

0,15

1 0,1
0,25

15 15
7,26
+0,05

0,25

11 11
10,26
10,2

21 25 21 25
0,48
0

1,4
2,1
0,48
2,1
1,4
0,5

4x

12 24 23 12 24 23

10x 11,67 4,5 0,25

0,5 A B 0,97 0,15 3,4 0,25
0,4 A 12,67
0,97 0,15
10x 19,67
3,7 0,25
0,5 A C
0,4 A 20,17 5,87 0,15

Remark:
Positional tolerances according to DIN EN ISO 5458

2
09-2011, Rev. 0911 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company. http://relays.te.com/definitions
 Automotive Relays
PCB Double Relays

Double Micro Relay K (THT – THR) (Continued)

Dimensions
23,6 0,2
Double Micro Relay THR
6,2 0,1

2,5 0,2
23,6 0,2
0,6 0,2
6,2 0,1

2,5 0,2

0,6 0,2
0,2 2)

0,1

0,2
0,1

0,17,65
0,1 0,7

0,210,2
2,5
0,2 2)

7,65
0,7

10,2
2,5

12,9 0,3

0,95 0,2

12,9 0,3

0,95 0,2

View of the Terminals View of Stand-Offs

Bottom view on solder pins Bottom view on solder pins

8,5 8,5
0,0 x
6x
6
0 ,05

0 5

7,5 7,5 0,15 0,15

5,87 5,87
0
1,2 +

1,2 +

C C 0,5 0,5 0,25 0,25

3,7 3,7
B B 0,25 0,25
3,4 3,4 0,15 0,15
0,97 0,97
1,72 1,72
0,25 0,25
4,5 4,5 0,15 0,15
0,97 0,97
0,06

0,06

13 13 14 14 22 22 13 13 14 14 22 22
0,15

0,15
3,6
4x

3,6
4x

0,48 0,25
0,25
0,25
6,66

6,66
1,37

1,37

0,48 0,15

1 0,1
0,15

1 0,1
0,25

0,25

15 15 15 15
7,26
+0,05

7,26
+0,05

0,25

1,4 0,25

11 11 11 11
10,26

10,26
10,2

10,2

21 21 25 25 21 21 25 25
0,48
0
0,5 0

1,4
2,1
1,4
2,1
0,48
2,1

2,1
1,4
0,5

4x

4x

12 12 24 24 23 23 12 12 24 24 23 23

10x 10x 11,6711,67 0,25 0,25

4,5 4,5
0,5 0,5 A B A B 0,15 0,15
0,97 0,97 0,25 0,25
3,4 3,4
0,4 0,4 A A 12,6712,67
0,15 0,15
0,97 0,97
10x 10x 19,6719,67 0,25 0,25
3,7 3,7
0,5 0,5 A C A C
0,4 0,4 A A 20,1720,17 0,15 0,15
5,87 5,87

3
09-2011, Rev. 0911 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company. http://relays.te.com/definitions
 Automotive Relays
PCB Double Relays

Double
Micro Relay K (THT – THR) (Continued)

Product code structure Typical product code V23086 -C 20 01 -A 4 03

Type
V2086 Micro Relay K (THT-THR)
Terminal and enclosure
C PCB version THT, sealed R PCB version THR, vented
Design
20 Double relay (THT) 28 Double relay (THR)
Coil
01 Standard 02 Sensitive
Contact type
A Single contact
Contact material index
4 AgSnO2 standard 8 Wiper load
Contact arrangement index
03 form C (CO)

Product code Terminal/Encl. Design Coil Contact Cont. material Arrangement Part number
V23086-C2001-A403 PCB THT, imm., clean Double Standard Single AgSnO2 2 form C, 2 CO (standard) 0-1413009-9
V23086-R2801-A403 PCB THR, vented relay 6-1414920-1
V23086-R2802-A803 Sensitive 2 form C, 2 CO (wiper load) 8-1414964-5
This list represents the most common types and does not show all variants covered by this datasheet.
Other types on request.

4
09-2011, Rev. 0911 Datasheets and product specification ac- Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com cording to IEC 61810-1 and to be used only terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company. http://relays.te.com/definitions