ST-1509 User Manual

CBN033049(B)
Chisel solder tip (type D) Figure Model

T9130-1.6D

T9130-2.4D

T9130-3.2D

T9130-4.6D

Cone solder tip (type I) Figure Model

T9130-0.5I

T9130-1.0I

Knife-shaped solder tip (type K) Model

Figure

T9130-K

Y9150 series
Beveled solder tip (type C) Figure Model

T9150-3C

T9150-5C

T9150-6.5C

Chisel solder tip (type D) Figure Model

T9150-3.2D

T9150-4.6D

T9150-6.5D

Knife-shaped solder tip (type K) Figure Model

T9150-K

13
Specification and model of integrated heating element
Y950 series
Beveled solder tip (type C)
Figure Model

T950-1.2C

Chisel solder tip (type D) Figure Model

T950-1.3D

T950-2.2D

T950-3.0D

Cone solder tip (type I) Figure Model

T950-0.5I

Knife-shaped solder tip (type K) Figure Model

T950-K

N9100 series
Chisel solder tip (type D) Figure Model
T9100-1.3D

T9100-2.2D

T9100-3.0D

Cone solder tip (type I) Figure Model

T9100-0.5I

Y9130 series
Beveled solder tip (type C) Figure Model
T9130-1.2C

T9130-2.4C

T9130-3.2C

T9130-4.6C

12
 Replacement of Heating Core of Y950 Handle

1 Putting the handle into the stand slot to pull its integrated heater out, then put the
integated heater in the hole of stand.

Replacement of Heating Core of Y9130 and Y9150 Handles

Power cord
Main host
Soldering handle
1 Putting the handle into the stand slot to pull its integrated heater out, then put the
integated heater in the hole of stand.

Iron stand

Packing list: Main host + Soldering handle

+ Iron stand + Power cord + Manual

11
Product specification and model

Model Y950 Y9130 Y9150 N9100 ST-1509

Voltage
Power 150W

consumption
Temperature T1.6A(230VAC) T3A(110VAC)
range
80℃~480℃/176℉~896℉
Cable material Heat-resisting silica gel
Type of
Integrated heating element
heating core
Temperature Thermocouple
sensor 30

Model of Y950 Y9130 Y9150 N9100

heating core series series series series
Note: Replacing the handle or heater may cause temperature inaccurate,
if the temperature is inaccurate, we suggest use the temperature
3
calibration function.

Replacement of heating element

Replacement of Heating Core of N9100 Tweezers

10
 (means:ST-1509 V0.1 version)

30

2.Enter standby mode

150 standby
(Default standby mode after 1 minute.)

3.Enter sleep mode (only after turning on the standby function) E02:Sensor alarm(diagram 1-25)
E03:Zero-cross detection abnormal alarm(diagram 1-26)
（Only when the standby function is on can it be used. By default, it will enter E04:Abnormal temperature alarm
the sleep mode after 30 minutes.） E05:over-current protection
E07:Short circuit of sensor

S 8
REAL E08:Abnormal soldering tip temperature
E09:The soldering pen has been removed

e02 e 03
SL P
REAL SET
Under the H-L menu, press “▲”and “▼” button to set the upper lower temperature values and
OFF. (diagram 1-19) It will alarm if upper temperature more than 20℃(68℉) and the lower
temperature less than -20℃(68℉). (diagram 1-20) alarm function is OFF. The upper and lower
temperature rang is 20℃ to 80℃(68℉ to 176℉).

Under the PSD menu, press “▲” and “▼” button to adjust the password setting value.The
password value can be set from “01" to “999". (diagram 1-21) Display 01 means the password
function is turn on, (diagram 1-22) to enter the menu interface. The first time you enter the
password in not set, press 2 button to enter the menu mode, then set the password and press
2 button to confirm the menu.
(Note: Directly enter password 906 to enter the menu interface in case of forgetting the password)

0P S 0l
SET

e
SET

l 9
5.Auto-standby function
Under the STB menu, press "▲" and "▼" to set the standby parameters:Off/On Time:10~60
(default 1) minutes. the heater temperature is 150 ℃ under standby status. (diagram 1-14)
open the auto standby function, and the standby time is 20 minutes. (diagram 1-15) turn off the
auto standby function . In standby mode, pick up the soldering tool or press any key to
automaticallyresume normal operation. (Note: If the device is not in a static state, it will affect the
device to enter auto sleep)

2S 80Y o fS 8fY
SET SET

6.Auto-sleep function
Note: The auto sleep function needs to be used when the auto standby function is turned on.
When the auto standby function is turned off, the auto sleep function is turned off at the same
time. The auto sleep function cannot be turned off when the auto standby function is turned on.
Under the OFF menu, press "▲" and "▼" button can be set the heating time:10~60(default 30)
minutes. When the heating state is turned off, pressing any button will automatically resume the
normal working mode.
Example:The standby time is 10, and the sleep time is 20. The total time is 30 minutes. After
heating is turned off, the heating core is not heated.

2S0L P
SET