0% found this document useful (0 votes)
35 views6 pages

Manual For Nano Receiver

Uploaded by

tgvfd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
0% found this document useful (0 votes)
35 views6 pages

Manual For Nano Receiver

Uploaded by

tgvfd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 6
/& BETAFPV Nano Receiver User Manual BETAFPV Nano receiver is based on ExpressLRS project, open source RC link for RC applications. ExpressLRS aims to achieve the best possible link preformance in both speed, latency and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range preformance. Github Project Link: https://github.com/ExpressLRS Facebook Group: https://www.facebook.com/groups/636441730280366 | Specifications + Weight: 0.7g (receiver only) + Size: 12mm*19mm «Telemetry power: 20dbm + Frequency bands (Nano receiver 2.4G version): 2.4GHz ISM + Frequency bands (Nano receiver 915MHz/868MHz version): 915MHz FCC/868MHz EU + Input voltage: 5V «Antenna connector: IPEX MHF Nano receiver 2.4G version diagram as show below. LED IPEX MHF WIFI Antenna PA+LNA Firmware Upgrade Button ESP8285 $X1280 GND 5V TX Nano receiver 868MHz/915MHz version diagram as show below. LED IPEX MHF WIFI Antenna Firmware Upgrade Button SX1276 ESP8285 Nano receiver LED status indication as show below. Indicator status Meaning Solide on Connected successfully Flash double quickly Binding status Flash slowly Connection fail Flash qucikly WIFI upgrade status | Basic Configuration https://github.com/ExpressLRS/ExpressLRS/wiki/OpenTX-and- Betaflight-Setup ExpressLRS uses the Crossfire serial protocol (AKA CRSF protocol) to communicate between the receiver and the flight controller board. So make sure your flight controller board support the CRSF serial protocol. Next, we use the flight controller with Betaflight firmware to show how to setup the CRSF protocol. The connection between ELRS Nano receiver and FC board is show as below. Enable the corresponding UART (e.g. UART3 below) as a Serial Rx on Betaflight Configurator "Ports" tab. USB VCP @™D 115200 v UART1 115200 v UART2 115200 v UART3 115200 ¥ ea On the "Configuration" tab, select "Serial-based receiver" on the "Receiver" panel, and select "CRSF" as the protocol. Telemetry is optional here and will reduce your stick update rate due to those transmit slots being used for telemetry. Isle ‘Serial-based receiver (SPEKSAT,£ ¥ | Receiver Mode Note:Remember to configure a Serial Port (via Ports tab) and choes a Serial Receiver Provider when using RX_SERIAL ferture _CRSF vy Serial Receiver Provider | Bind Nano reciever could enter binding status by power on/off three times. + Plug in and unplug nano receiver three times; + Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode; + Make sure the RF TX module or radio transmtter enter binding status, which sends out a binding pulse; «If the receiver has a solid light, it's bound. Note: Binding onece and the receiver will store the binding information. Re-power and the connect successfully auto. | More Information As ExpressLRS project is still in frequently update, please check BETAFPV Support (Technical Support -> ExpressLRS Radio Link) for more details and newest maunal. https://support.betafpv.com/hc/en-us + Newest user manual; + How to upgrade the firmware; + FAQ and troubleshooting.

You might also like