Program Instructions:

1. Delete the existing code of our remote duplicator

1)Click and Hold A and B buttons together - Led will flash 3 times.
2)Keep holding A button and release B button.
3)Keep holding A button and push B button 3 times, Led will start flashing Non-stop.
Now press any key on the remote control, LED lights are not bright, so delete code success; if you
press the button LED lamp is lit, indicating that the original code is not deleted !
2. Clone your original remote
1)Put both remotes Into back to Back position. Make sure they have direct contact.
2)Click and hold 1 button on your original remote and 1 button on your clone remote. Keep holding
until led will make 2 blinks.
3)Blinks then goes into Steady and you have successfully cloned. (the left keys follow the same
above operation)
If for some reason the clone does not go further then 2 blinks, it means the signal does not go
through, please shift the remote slowly up and down until you get the point where it will go through.

Features:
Privacy is strong. Each key password alone save. Easy to use.
Stable signal can pass through walls, floors, doors or windows.
Widely used in Vehicle central locking systems, Garage doors, Electronic gates, Electrical
appliances, Home automation, lights, Car sunroofs, Car/Motorbike alarms, etc.
Remote Control only, other accessories demo in the picture are not included!

Tips:
1. The essential condition for the selection of the remote control;the copyed remote control operates
normal,chip is compatible and frequency is correct.
2. Before buying ,please make sure the copyed remote control operating frequency or choose & buy
the frequency adjustable type remote control.
3. Before buying,please confirm whether your remote control can be copyed or not.
4. The remote control can copy the fixed codes and learning codes. It can't copy original car remote
control, two-way remote control and rolling code remote control (Rolling code chips start with HCS
commonly,such as HCS200,HCS201,HCS300,HCS301,etc)

Specification:
Model: KB1815
Material: ABS+Metal
Rated Voltage: 12V
Frequency: 433MHz
Wireless Communication: RF
Encoding Type: Self Copy
Modulation: ASK (Amplitude Modulation)
Wireless Transmitting Distance: 50-100m (Open Space)
Color: As Pictures Shown
Size: One Size
Diameter: 4.8cm/ 1.89in
Height: 1.5cm/ 0.59in
Quantity: 1 Pc

Package includes:
1 x Remote Control (with battery)
Note:
1.No retail package.
2.Please allow 0-1cm error due to manual measurement. plz make sure you do not mind before you
bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of the
item. Thank you!

Operation Manual:
1. Clean code: shut at the same time hold the lock with two keys (some of the shell are the two key)
upward and downward, the LED indicator lights flashing three times, press release any one of the
key, another is not loose, click the release button three times, rapid flashing LED light into the state,
at this time of memory data all cleared, after cleaning the data of the remote control, press any key,
the LED indicator is on.
2. Copy: One hand-held original remote controller, the other hand-held copy remote controller, two
remote controllers as close as possible, (ideally two remote controllers zero distance side by side on
the desktop) respectively press the required copy buttons, LED indicator flickers quickly after three
flickers, copy success, other key operation method is the same. Some remote controllers have low
transmitting power, so they should be equipped with remote controllers and back-to-back operation
of copying remote controllers to cope well. If there is interference in some operating environments,
interference operation should be avoided. If copying is not good, copying should be done again after
code clearance.
3. Recovery: When you inadvertently clear the code of the copying remote controller, you can press
the bottom two keys of the copying remote controller at the same time. After three flashes of
the LED lamp, it will flicker quickly. After release, you press any key again and the light is long,
which indicates that the code of the copying remote controller has been restored. Before using our
copy remote control to copy, please make sure to clear the existing code of the copy remote control
first.

4. How to control some of the keys after copying, and the rest can not be controlLED, you can use
the tips of cleaning and restoring operation, the specific operation is as follows:
(1) Clearing the code first.
(2) Copy the keys that have not been copied successfully again after the successful code clearance,
and do not copy the keys that have been copied successfully before.
(3) Clearing the code again.
(4) Make a restore operation once; at this time, the key that had not been successfully copied was
covered by the new copy code, while the original copy of the successful code was retained. If there
are still keys that have not been copied successfully after the second copy, they can be coded again,
and the keys that have not been copied successfully can be copied again, and then coded and
restored again. This is repeated until all keys are successfully copied. This little trick can be used to
reduce the hassle of repetitive operations.

Warm Tips:
1. Prerequisites for selecting the duplicate remote controller: the original remote controller has
normal function, the remote control chip is the same or compatible, and the remote control work
frequency is the same.
2. The copying remote controller can only copy fixed code, learning code chip and remote controller
of some single chip computers (the type of chip that can be copied is shown in the description of the
type of chip that can be copied).
3. Two-way remote controller, scroll code remote controller and single-chip encryption program
remote controller can not be copied. Such as HCS200, HCS201, HCS300, HCS301, etc.
4. Before copying the remote controller, make sure that the existing code of the remote controller
has been cleared and check whether the code has been cleared successfully. Otherwise, replication
is not possible.
5. Make sure your remote controller has enough power when copying. The closer the two remote
controllers are, the better. If the copy distance is too close, the switch can copy from different angles.
Pressing the button of the original remote control requires that the transmitting signal be completely
normal, and then press the button of the duplicate remote control to ensure that the function is
completely duplicated.