CableTraySystems Interflex
CableTraySystems Interflex
CableTraySystems Interflex
our wire-mesh
cable tray program with We are grateful for
All accessories and complements of the system comply with our two basic premises:
Safety for installers and conductors and Easiness of installation.
Multiadvantages cable trays
Self coupling sheet steel cable tray
Highest care
A rounded protection at
the base of the cable tray
protects the cables from
shipping while pulling.
Highest guarantee Highest strength
Highest comfort Cable tray Reinforced base and wings with longitudinal
Inlaid fitters to hide and accessories and traverse profiles
the bolts and guarantee identified with that enable the fixation
a good traction our tradenames. of the cover without
and distribution accessories.
of the conductors.
In accordance with European Directive INTERFLEX S.A. has decided to use trivalent
2002/95/CE (RoHS) and the later modifications chrome (Cr 3+) instead, a product that allows
2005/717/CE and 2005/747/CE, a high degree of protection and presents
the use of dangerous substances, such as a silver finish that differentiates it from
hexavalent chrome (Cr 6+) is forbidden. the bright yellow colour of hexavalent chrome.
That means that hexavalent chrome, that In spite of the fact that trivalent chrome
had previously been used in the passivating can be dyed with the use of colourings,
of the zinc coating for cable trays protection this does not improve the resistance
against corrosion, has to be replaced to corrosion and can cause confusion
for another non-polluting material. to the user, favours pollution and fades
with time.
These are the reasons why the car industry,
pioneer in labour and environmental safety,
has declined the use of colourings
in the passivating of the electrozincated
products it uses.
new
The superior coating
+ environmentally friendly
This new treatment with trivalent chrome (Cr 3+)
will replace at the same time the hexavalent
bichromated zinc plating (Z) and the zinc plating
(ZP) finishes.
The new Z3 is environmentally friendly and
non-pollutant, fulfilling INTERFLEX S.A.'s
comittment in contributing to the
environmental protection.
+ resistant
This new Z3 treatment has an equivalent protection
against white corrosion appearance as the old
hexavalent bichromated zinc plating (Z) finish and
has a much greater protection against white corrosion
than the zinc plating (ZP).
+ rational
The use of a unique coating (Z3) instead of the two
previous ones (Z and ZP), allows a stock reduction
for both our customers and installers, providing less
occupied space and better service.
In short, with the new Z3 coating, VIAFIL MULTIVIA
cable tray follows once again the main trend
in the European market.
Follow us!
Cable
Flexibilidad tray
de montaje
System overview
Visión general del sistema
Easy assembly
10
A wide range of supporting elements
5 6
11
Tray side 30
Coatings:
Ecologic zinc plating
Hot dip galvanized
I Stainless steel AISI 304L/316L Passivated
50 50
200 /300
B
200
PERMISSIBLE LOAD. (N/m)*
100
300
150
200
100
50 100
0
1 1,25 1,50 1,75 2
SPAN BETWEEN SUPPORTS (m)
* Values obtained using UUR.. couplers on sides and bottom.
12
All measurements in mm
Tray side 60
Coatings:
Ecologic zinc plating
Hot dip galvanized
I Stainless steel AISI 304L/316L Passivated
30
30
56
62
60 50
100
60 x 150
30
62
Reference B Weight Useful cross section m/pack
kg/m mm2
R0606Z3 60 0,67 2230 24 50
R0610Z3 100 0,96 4390 24 150
R0615Z3 150 1,02 7040 24
R0620Z3 200 1,32 9460 12 60 x 200 a 60 x 600 30
R0630Z3 300 1,68 14660 12
62
R0640Z3 400 2,04 19860 6
R0650Z3 500 2,86 25060 6
R0660Z3 600 3,29 30260 6 50 50
200 / 600
R0606G 60 0,77 2230 24
R0610G 100 1,10 4390 24
R0615G 150 1,17 7040 24
R0620G 200 1,52 9460 12
100
800
600
R0615I 150 1,02 7040 24
R0620I 200 1,32 9460 12 500
600
R0630I 300 1,68 14660 12
R0640I 400 2,04 19860 6 400
R0650I 6 400
500 2,40 25060
R0660I 600 2,77 30260 6
300
200 200
150
100
60
0
1 1,25 1,50 1,75 2
SPAN BETWEEN SUPPORTS (m)
* Values obtained using ULR06..couplers on sides and UUR.. on bottom.
13
All measurements in mm
Tray side 110
Coatings:
Ecologic zinc plating
Hot dip galvanized
I Stainless steel AISI 304L/316L Passivated
30
R1050Z3 500 3,34 49260 6
R1060Z3 600 3,78 59460 6
40
112
R1020G 200 1,95 18660 6
R1030G 300 2,38 28860 6
R1040G 400 3,34 39060 6 42
R1050G 500 3,84 49260 6
R1060G 600 4,35 59460 6 50 50
R1020I 200 1,66 18660 6 200/600
R1030I 300 2,02 28860 6
R1040I 400 2,39 39060 6
R1050I 500 2,75 49260 6
R1060I 600 3,11 59460 6
100
B
PERMISSIBLE LOAD. (N/m)*
1400 600
1200
500
1000
400
800
300
600
400 200
1 1,25 1,50 1,75 2
SPAN BETWEEN SUPPORTS m)
* Values obtained using ULR06..couplers on sides and UUR.. on bottom.
14
All measurements in mm
Complements Coatings:
S Sendzimir galvanized
TB06G 60 0,67 24
TB10G 100 0,72 24
TB15G 150 1,00 12
TB20G 200 1,28 12
TB30G 300 2,14 6 When covering 60 & 110 side trays,
TB40G 400 2,78 6 use ULR06 side coupler.
TB50G 500 3,91 6
TB60G 600 4,65 6
TB06I 60 0,54 24
TB10I 100 0,63 24
TB15I 150 0,87 12
TB20I 200 1,11 12
TB30I 300 1,86 6
TB40I 400 2,42 6
TB50I 500 3,40 6
TB60I 600 4,04 6
400
A
TSR03G 30 23 0,46 30
TSR06G 60 53 0,74 30
TSR10G 110 95 1,05 30 To separate electrical networks
of different characteristics
Use BFTG clamps
15
All measurements in mm
Coatings:
Accessories Ecologic zinc plating
S Sendzimir galvanized
Hot dip galvanized
Multipurpose coupler I Stainless steel AISI 304L/316L Passivated
SIDE 30
15 22
UURI 0,03 50
15
22
ULR06I 0,07 50
For coupling 2 cable tray stretches SIDES 60 and 110, you will need:
Widths 60-100-150: 2 pcs. ULR06..
Widths 200-300: 2 pcs. ULR06.. + 1 pc. UUR..
Widths 400-500-600: 2 pcs. ULR06.. + 2 pcs. UUR..
16
All measurements in mm
INSTA-FIX Side coupler
¡CLICK!
1 B
8
A
220
23,5
40
21,5
Ø 20
114
Ø 25
75
Ø 34
100
VIAFIL Fixation
clamp to support
22 15
FSRI 0,02 50
Dividing strip
fixation clamp for VIAFIL
6,5 x 6,5
20
15
TCA670Z3 M6 x 70 0,02 50
TCA820Z3 M8 x 20 0,02 50
TCA860Z3 M8 x 60 0,03 50
TCA620G M6 x 20 0,01 50
TCA820G M8 x 20 0,02 50
TCA620I M6 x 20 0,01 50
19
All measurements in mm
Conformation and
assembly examples
90º angle
Width 60
500
260
UUR...
Pcs. needed
1
Easy assembly
UUR...
Pcs. needed
2
D F
Width D F
100 300 100
150 400 200
200 400 200
F 300 500 300
400 600 400
500 700 500
600 800 600
Easy assembly
20
All measurements in mm
Widths 100 and 150
700
UUR... 375
Pcs. needed
1
Easy assembly
UUR... SCR.. L
Pcs. needed
1 1
Width D F L
200 525 100 1000
300 625 200 1200
400 725 300 1400
F
500 825 400 1600
600 925 500 1800
Easy assembly
21
All measurements in mm
Conformation and
assembly examples
Widths 60 to 600
D D
Easy assembly
22
All measurements in mm
Level change
Easy assembly
23
Conformations and
assembly examples
Derivation
UUR..
Pcs. needed
4
Easy assembly
24
Reduction
P c s . n e e d e d
3 2 1
100 mm reduction
200 mm reduction
Easy assembly
25
Coatings:
Supports
Ecologic zinc plating
30
6,5 x 10
Ø 8,5
105
Central suspension
clamp for VIAFIL
50
35
SCRI 0,04 50
Use 2 pieces for each suspension with VS8.. rod only for sides
100-150-200 with light and equilibrated loads.
8 x 20 50
14
26
All measurements in mm
INSTA-FIX support
for trapeze suspension
80
11
60
Place Bend
Place Bend
27
All measurements in mm
Coatings:
Ecologic zinc plating
Elements for supports
Hot dip galvanized
I Stainless steel AISI 304L/316L Passivated
Threaded hanging rod P Bluing
Length 1 m
C6923.8I M8 0,01 50
C6923.10I M10 0,01 50
VERTICAL
Ceiling fixation Load: 700N
(2 coupled pieces)
10,5 x 18
10,5 x 18
65
40 35
INCLINED
Reference Weight pcs./pack Load: 700 N
kg/u
(2 coupled pieces)
FTZ3 0,10 10
28
All measurements in mm
Horizontal fastening clip
de 4 a 10 40
52
M8
40 19
de 4 a 10
92
M8
44
29
All measurements in mm
Supports Coatings:
S Sendzimir galvanized
58 20
30
50
75
9 x 15
SDRI 0,84 10
Place Bend
Place Bend
30
All measurements in mm
Distancing support
B
Wall fixation
9 x 15 60
6,5 x 25
37,5
47
9 x 15
Floor fixation
31
All measurements in mm
“OMEGA” supports and elements Coatings:
Ecologic zinc plating
50
110
9x20 B
50
20
L
57
“OMEGA” profile
ceiling support
110
180
9x20 B
50
57
Support load capacity
Reference Cable tray B L Weight pcs./pack Reference Cable tray Load (N)
width kg/pc. width
32
All measurements in mm
“OMEGA” profile
for trapeze suspension
Length 2 m
50
9x20
57 L
Use VS8.. hanging rod. For an easier assembly, use TSOZ3 shims.
57
9x20
L
50
20,5 34
50
6,5x25
45
50
50
SSH20S 200 241 0,41 10
86
SSH10G 100 141 0,30 10
SSH15G 150 166 0,34 10 6,5x15
20,5 34
50
6,5x25
45
50
A
8,5 11
111
width kg/pc.
SSH30S 300 341 0,84 10
SSH30G 300 341 0,92 10
6,5x15
20,5 34
50
6,5x25
45
50
A
8,5 11
75
121
6,5x15
34
All measurements in mm
20,5 34
50
6,5x25
45
50
A
8,5 11
125
162
6,5x15
For fixation over a “C” profile use 2 TE1015Z3 bolts with TG10Z3
guided locknuts.
35
All measurements in mm
Supports
6,5 x 25
20 50 79,5
24
40
20
166
40
85
30,5
50
Reference Cable tray Weight pcs./pack
width kg/pc.
11
SIC10G 100 0,19 10 10,5x15
6,5 x 25
20 50 104,5
24
40
20
191
40
85
30,5
50
Reference Cable tray Weight pcs./pack 11 50
width kg/pc. 10,5x15
40
20
266
40
32,5
50
95
11
50 10,5x15
Reference Cable tray Weight pcs./pack
width kg/pc.
SIC20G 200 0,37 10
6,5 x 25 30
20 50 79,5
24
40 20
366
40
32,5
50
105
6,5 x 25 30
20 50 79,5
24
40
20
466
40
50
33
112
36
All measurements in mm
From above From below
Bend tabs after
Place Bend
placing VIAFIL
cable tray
Place Bend
6,5 x 25 30
20 50 79,5
24
40
20
50
566
33
100
143
50
11 50 10,5x15
6,5 x 25 30
20 50 79,5
24
40
20
666
50
33
100
143
50
11 50
10,5x15
37
All measurements in mm
Supports Coatings:
S Sendzimir galvanized
45
A
Reference Cable tray A Weight pcs./pack
width kg/pc.
11
SHE10S 100 122 0,22 10
SHE15S 150 172 0,28 10
50
86
SHE20S 200 222 0,31 10
11x13
SHE10G 100 122 0,24 10
SHE15G 150 172 0,31 10
SHE20G 200 222 0,34 10 6,5x15
45
A
11
111
75
11x13
6,5x15
11
75
121
11x13
6,5x15
38
All measurements in mm
6,5x25 6,5x15 5 17,5
45
A
11
20x32
125
162
11x13
6,5x15
39
All measurements in mm
Supports
6,5 x 25 5
65
24
40
6,5 x 15
20
40
171,5
85
Reference Cable tray Weight pcs./pack
50
22
width kg/pc.
SEC10G 100 0,15 10
11
10,5x15
6,5 x 25 5
65
24
6,5 x 15 40
20
40
221,5
85
50
22
Reference Cable tray Weight pcs./pack
width kg/pc.
11 50
SEC15G 150 0,19 10 10,5x15
6,5 x 15 6,5 x 25 5
24 65
40
20
40
271,5
50
95
23
6,5 x 15 6,5 x 25 5
65
24
40
20
40
371,5
50
105
23
11 50 10,5x15
Reference Cable tray Weight pcs./pack
width kg/pc.
SEC30G 300 0,45 10
6,5 x 15 6,5 x 25 5
65
24
40
20
40
471,5
50
24
112
11
50 10,5x15
40
All measurements in mm
6,5 x 15 6,5 x 25 5
65
24
40
20
50
571,5
24
100
143
11 10,5x15
50
40
20
50
671,5
24
100
143
11
50 10,5x15
For fixation over a “C” profile use 2 TE1015Z3 bolts with TG10Z3
guided locknuts.
Length 3 m 41
2,5
20,5
7,5
22
13x30
50
“C21” profile
with head plate
80
130
170
10,5x21
5
25
50
13x30
To be used with SSH.., SHE.., SIC and SEC supports fixing them
with TE1015Z3 bolts and TG10Z3 guided locknuts.
Use SO “OMEGA” supports fixing them with TE835Z3 bolts,
42 TG8Z3 guided locknuts and TSOZ3 shims.
All measurements in mm
Double “C21” profile
with head plate
80
170
130
43
10,5x21
5
25
50
13x30
Balanced load = 5 KN
Reference L Weight pcs./pack
kg/u
PDCB50G 500 2,57 1
PDCB100G 1000 4,48 1
To be used with SSH.., SHE.., SIC and SEC supports fixing them
with TE1015Z3 bolts and TG10Z3 guided locknuts.
Guided locknut
for “C” profiles
34
MB
A
20
Hexagonal bolt
for guided locknut
Length 3 m 41
2,5
41
7,5
22
13x30
50
With load applied only at one side, use SHE.., SSH.., SIC or SEC
supports fastening them with TE1015Z3 bolts and TG10Z3
guided locknuts. With even loads on both sides use 2 TE1070Z3 bolts
and C6923.10Z3 toothed locknuts.
60,5
100
Ø10,5
50
15X10,5
130
170
37
42,6
44
All measurements in mm
Guided locknut
for “C” profile
34
MB
20
A
Toothed locknut
for “C41” profile
45
All measurements in mm
Cable tray
System overview
46
A whole range of supporting elements
To floor
7
1
10
r
ON Fastgeher
TI Tou aper 9
ALLA Che
INST
Assembly instructions for the self-coupling edges cable tray
A B C D
TCA612.. x3 47
Perforated cable tray side 35
Coatings:
S Sendzimir galvanized
Hot dip galvanized
LIN G
F - C OUP
S E L T R AY
B
250
PERMISSIBLE LOAD (N/m)*
300
7x30
200
150 200
150
100
100
50
0
1 1,25 1,50 1,75 2
Coatings:
S Sendzimir galvanized
Hot dip galvanized
LIN G
F - C OUP
S E L T R AY
B
1000
PERMISSIBLE LOAD (N/m)*
600 7x30
800
500
600
400
400 300
200
200
100
150
0
1 1,25 1,50 1,75 2
Coatings:
S Sendzimir galvanized
Hot dip galvanized
LIN G
F - C OUP
S E L T R AY
B
1250 600
PERMISSIBLE LOAD (N/m)*
7x30
1000 500
400
750
300
500
200
150
250
100
0
1 1,25 1,50 1,75 2
Coatings:
S Sendzimir galvanized
Hot dip galvanized
IN G
C O UPL
F-
S E L T R AY
B
1800
PERMISSIBLE LOAD (N/m)*
600 7x30
1500
500
1200
400
900
300
600
200
150
300 100
0
1 1,25 1,50 1,75 2
Coatings:
S Sendzimir galvanized
Hot dip galvanized
ING
UPL
E L F - C OAY
S TR
B
1000
PERMISSIBLE LOAD (N/m)*
600
800
500
600
400
400 300
200
200
100
0
150
1 1,25 1,50 1,75 2
Coatings:
S Sendzimir galvanized
Hot dip galvanized
PL ING
L F - COU
SE Y
TRA
B
1250
PERMISSIBLE LOAD (N/m)*
600
1000 500
400
750
300
500
250
150
250
100
0
1 1,25 1,50 1,75 2
Coatings:
S Sendzimir galvanized
Hot dip galvanized
PL ING
L F - COU
SE Y
TRA
B
1800
PERMISSIBLE LOAD (N/m)*
600
1500
500
1200
400
900
300
600
200
150
300 100
0
1 1,25 1,50 1,75 2
50 7 x 30 37,5
Width 100 Width 500 (Side 60)
12,5
81
28
75
180
12,5
99
75 75 7 x 45 Ø 11
Width 150
140
7 x 45
7x40
25
36
28
78
74
180
36
25
106
Rest of dimensions: the
same as the ones for width 100 37,5
Rest of dimensions: the same as the ones for width 200
Width 200
Width 500 (Sides 85 y 110)
61
80
7x45
78
61
Width 300
80
80
140
7x40
Width 600
80
Width 400
49 25 56
130
340
7x40
140
7x40
130
130
Rest of dimensions: the same as the ones for width 200 Rest of dimensions: the same as the ones for width 400
55
All measurements in mm
Complements and accessories
Coatings:
Sendzimir galvanized
Cable tray cover S
Hot dip galvanized
Length 3 m
450
A
TSC03G 35 28 0,46 30
TSC06G 60 53 0,74 30 To separate electrical networks
of differents characteristics
TSC08G 85 78 0,89 30
TSC10G 110 100 1,05 30
56
All measurements in mm
Lateral bendable coupler
Fixed coupler
B 6,5 x 16,5
8,5
6,5 x 10
A
Bendable joining
57
Cable trays
for illumination and complements Coatings:
S Sendzimir galvanized
55
75 97
60
28
Reference Weight pcs./pack
kg/u
ULC10S
P0506S 0,93 24 75 7 x 45 Ø 11
55
50
60
Reference Weight pcs./pack
kg/u
ULC10S
C0506S 1,27 24
SIDE 55 coupler
180
6,5 x 10
39
Multipurpose support 42
for 55x60 cable tray 9 x15
9 x15
120
7x10 7x35
45
S Sendzimir galvanized
45º Elbow Hot dip galvanized
60
All measurements in mm
45º Elbow cover
61
All measurements in mm
Complements
Coatings:
S Sendzimir galvanized
90º Elbow Hot dip galvanized
62
All measurements in mm
90º Elbow cover
63
All measurements in mm
Complements
Coatings:
S Sendzimir galvanized
90º Inside bend Hot dip galvanized
300
CV0640G 60 400 205 2,14 1
CV0650G 60 500 205 2,46 1
A
64
All measurements in mm
90º Inside bend cover
65
All measurements in mm
Complements
Coatings:
S Sendzimir galvanized
90º Outside bend Hot dip galvanized
66
All measurements in mm
90º Outside bend cover
67
All measurements in mm
Complements
Coatings:
S Sendzimir galvanized
Derivation Hot dip galvanized
A
DT0320G 35 200 315 0,44 1
DT0330G 35 300 415 0,51 1
68
All measurements in mm
Derivation cover
69
All measurements in mm
Coatings:
Complements Ecologic zinc plating
S Sendzimir galvanized
Hot dip galvanized
Reduction or end piece I Stainless steel AISI 304L/316L Passivated
Central reduction
A
B
Reducción a la izquierda End piece
Use TCA612Z3 bolts wit toothed locknuts. Use TCA612G bolts with toothed locknuts.
70
All measurements in mm
Bolts with toothed locknuts
for VIATEC cable trays
TCA670Z3 M6 x 70 0,02 50
TCA820Z3 M8 x 20 0,02 50
TCA860Z3 M8 x 60 0,03 50
TCA620G M6 x 20 0,01 50
TCA620I M6 x 20 0,01 50
TCA820I M8 x 20 0,02 50
Ground connection
for VIATEC
For this application, use the FSR.. VIAFIL fixation clamp (pag. 18)
71
All measurements in mm
Supports Coatings:
S Sendzimir galvanized
Distancing support I
Hot dip galvanized
Stainless steel AISI 304L/316L Passivated
B
9 x 15 60 To wall
6,5 x 25
37,5
47
9 x 15
To floor
72
All measurements in mm
73
“OMEGA” supports and elements Coatings:
Ecologic zinc plating
S Sendzimir galvanized
“OMEGA” profile bracket Hot dip galvanized
50
110
9x20 B
50
57
“OMEGA” profile
ceiling support
110
180
9x20 B
50
57
Support load capacity
Reference Cable tray Load (N)
Reference Cable tray B L Weight pcs./pack width
width kg/pc. SO14.. 100 900
STO14S 100 145 170 0,56 1 SO19.. 150 900
STO24S 200 245 270 0,64 1 SO24.. 200 900
STO34S 300 345 370 0,76 1 SO34.. 300 900
STO14.. 100 700
STO14G 100 145 170 0,62 1
STO24.. 200 700
STO24G 200 245 270 0,70 1
STO34.. 300 700
STO34G 300 345 370 0,84 1
57 L
Use VS8.. hanging rod. For an easier assembly, use TSOZ3 shims.
57
9x20
L
50
75
All measurements in mm
Supports
Coatings:
S Sendzimir galvanized
Support for wall Hot dip galvanized
or “C” profile I Stainless steel AISI 304L/316L Passivated
45
A
Reference Cable tray A Weight m/Pack
width kg/m
11
SHE10S 100 122 0,22 10
SHE15S 150 172 0,28 10
50
86
SHE20S 200 222 0,31 10
11x13
SHE10G 100 122 0,24 10
SHE15G 150 172 0,31 10
SHE20G 200 222 0,34 10 6,5x15
45
A
11
111
75
11x13
6,5x15
11
75
121
11x13
6,5x15
76
All measurements in mm
6,5x25 6,5x15 5 17,5
45
A
11
20x32
125
162
11x13
6,5x15
For fixation over a “C” profile use 2 TE1015Z3 bolts with TG10Z3
guided locknuts.
77
All measurements in mm
Supports
6,5 x 25 5
65
24
40
6,5 x 15
20
40
171,5
85
Reference Cable tray Weight pcs./pack
50
22
width kg/pc.
SEC10G 100 0,15 10
11
10,5x15
6,5 x 25 5
65
24
6,5 x 15 40
20
40
221,5
85
50
22
Reference Cable tray Weight pcs./pack
width kg/pc.
11 50
SEC15G 150 0,19 10 10,5x15
6,5 x 15 6,5 x 25 5
24 65
40
20
40
271,5
50
95
23
6,5 x 15 6,5 x 25 5
65
24
40
20
40
371,5
50
105
23
11 50 10,5x15
Reference Cable tray Weight pcs./pack
width kg/pc.
SEC30G 300 0,45 10
6,5 x 15 6,5 x 25 5
65
24
40
20
40
471,5
50
24
112
11
50 10,5x15
78
All measurements in mm
6,5 x 15 6,5 x 25 5
65
24
40
20
50
571,5
24
100
143
11 10,5x15
50
40
20
50
671,5
24
100
143
11
50 10,5x15
For fixation over a “C” profile use 2 TE1015Z3 bolts with TG10Z3
guided locknuts.
Length 3 m 41
2,5
20,5
7,5
22
13x30
50
To be used with SHE.. and SEC supports fixing them with TE1015Z3
bolts and TG10Z3 guided locknuts. Use SO “OMEGA” supports fixing
them with TE835Z3 bolts, TG8Z3 guided locknuts
and TSOZ3 shims.
“C21” profile
with head plate
80
130
170
10,5x21
5
25
50
13x30
170
130
43
10,5x21
5
25
50
13x30
Guided locknut
for “C” profiles
34
MB
A
20
Hexagonal bolt
for guided locknut
Length 3 m 41
2,5
41
7,5
22
13x30
50
60,5
100
Ø10,5
50
15X10,5
130
170
37
42,6
20
A
Toothed locknut
for “C41” profile
83
All measurements in mm
General technical
information
84
MULTIVIA other materials: Table 1. Selecting the surface treatment
Performance:
I Stainless steel VG = very good
Numerous products of our catalogue are supplied G = good
P = possible
in steel no.14301 according to EN 10088 (AISI 304) S = superfluous
with excellent resistance characteristics to corrosion NA = not advised
in indoors, aggressive outdoors, highly humid
(industrial, chemical, marine,…) and aseptic environments
Applications Zinc chromatized Sendzimir Hot dip Stainless
(specially indicated for alimentary industry). electroplating galvanized steel
Upon request, we can also provide wire-mesh Indoors installation.
VG VG S S
cable trays and accessories in steel no.14404 (AISI 316L) Normal environment
Indoors installation
with excellent resistance to corrosion with high humidity NA NA G S
(specially indicated for chemical industry). Outdoors installation
Normal environment NA P VG S
Used both types in wire-mesh cables trays and accessories.
Marine environment (saline) NA NA P G
Acid environment NA NA NA P
The permissible load diagrams have been obtained
experimentally in our laboratory according Alcaline environment NA NA P P
to CEI 61537:2001 standard and load limitations Environment with
NA NA NA P
determined by: presence of halogens
85
General technical information
Calculation example
We are looking for a perforated sheet steel cable tray to house With a cross section of cables equal or superior to 30.707 mm2
the cables in these quantities and with these manufacturer and according to the column of useful cross section we can
specifications: choose among 60x600 mm, 85x400 mm and 110x300 mm
cable trays. In accordance to the permissible load capacity
Nominal External Total Weight Total Weight
diagrams, the longest span between supports would be 2 metres.
Qty of External
cables section (mm2) 2
diameter (mm) section (mm ) section (mm2) (Kg/m) (Kg/m) With 60x600 mm cable tray, ventilation is highly efficient, though
4 1x4 7,2 41 164 0,087 0,348 it takes up too much space; with 85x400 mm cable tray space
and ventilation are balanced and with 110x300 mm cable tray,
3 4x6 17,2 232 696 0,516 1,548
ventilation is not optimal.
8 4x70 35,5 990 7,920 3,574 28,592
6 3x150 44,9 1.583 9.498 5,550 33,300
S = 18.278 mm2 W = 63,788 Kg/m Electrical continuity
Assuming that we want to reserve 20% of the space (R=1,20), and ground connection
and appreciating that most of the cables are power cables
(C=1,40), the minimum useful cross section needed will be: Metallic cable tray systems should present an adequate
electrical continuity to ensure an equipotential connection
Su = 1,40 x 1,20 x 18.278 mm2 = 30.707 mm2
and one or many ground connections if necessary
(CEI 61537-01).
Amongst the different cable tray sizes for this useful cross
According to continuity assay no. 11.1 of CEI 61537-01 values
section, the ones closest to our calculated value to excess are
of impedance in MULTIVIA cable trays and joining materials
the ones measuring 60x600, 85x400 and 110x300 mm.
do not exceed 50 m Ω through the union of two cable trays
and 5 mΩ per metre of cable tray without the union.
Useful cross Ground connection of a cable tray system is achieved
Reference Side mm Width mm section (mm2)
connecting all elements of the system (every cable tray and
P0610S 60 100 5.320 all accessories) to a copper conductor with cover with a section
P0615S 60 150 8.220
not inferior to When using wire-mesh cable trays,
this connection can be made with BTL grounding clamp
P0620S 60 200 11.120 (page 19 in this catalogue) and when using sheet steel cable
P0630S 60 300 16.920 trays, it can be made with FSR.. clamps
(page 71 in this catalogue).
P0640S 60 400 22.720
P0650S 60 500 28.520
P0660S 60 600 34.320
86
The information contained in this catalogue is non-binding
and INTERFLEX reserves the right to modify it at any time
without further notice. 87
CABLE PROTECTION AND MANAGEMENT
Logistic Center
C/ del Mig, 82-84 - Pol. Ind. Pla d’en Coll
E-08110 Montcada i Reixac (Barcelona) Spain