Sat Avr-1

Site Acceptance Test (SAT)
SITE ACCEPTANCE TEST (SAT)
CUSTOMER : Chilime jalavidhyut company Limited

PROJECT : Chilime Hydro Electric Project,2x11.28MW
DOCUMENT NAME : AVR PANEL-1
DOCUMENT NO. : NICPL-137-01
Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Title: AVR PANEL-1 Project Title: Chilime Hydro Electric Project 2X11.28MW
Nelumbo Icona Controls Pvt Ltd
Noida India - 201301 Sheet: 1 of 33
Introduction
This document describes the Generator Relay Metering Panel item to be tested on a SAT period. The SAT
will demonstrate the operation and integration of the UCB,Governor system and verify the hardware
being supplied.
References
The following documents will be available as references during the SAT.
Ref Document Reference Description

1 NICPL-137-06-117 Wiring drawings
Manufacturer/Model Number Serial Number Cal Cert Ref Cal Exp Date
Relay tester / ISA DRTS 33 2119/48617
Digital Multi meter / Fluke 46311178WS
Health and Safety
The tests to be conducted involve test and measurement operations with hazardous voltages present. All
tests must be performed by skilled persons taking due care and attention to avoid electrical shocks. The
tests are to be performed in the stated sequence to avoid danger. All faults during electrical testing must
be rectified or deemed by a qualified and competent person not to compromise safety before further
testing can proceed.

Exciter Specification
Exciter Description
Make Alstom France
Excitation Brushless
Exciter Type RK 90-20B
Exciter current No load 8.3A
Nominal Exciter Current 16.6A
Exciter time constant at no load 0.376S
Ceiling Exciter Current 33.5A
Maximum Exciter voltage at VAn 306V
Nominal Exciter voltage 116VDC
Exciter voltage at no load 58VDC
Ceiling Exciter Voltage 235VDC
CHANNEL-1 SETTINGS
;-----------------------------------------
; ABB Switzerland Ltd
; CMT 1000 v6.200
;
; UN1020 Parameter File
; Saved: 18.04.2021, 12:36
; AVR Serial Number: 00046200/5005
; Control SW Version: 6.318
; MCU SW Version: 6.318
;-----------------------------------------
[SYSTEM DATA]
Ie Nominal = 16.5A
Potential Transformer = Three_Phase
UM Nominal = 11.000kV
UM Primary = 11.000kV
UM Secondary = 100.0V
UNet Nominal = 11.00kV
UNet Primary = 66.00kV
UNet Secondary = 110.0V
IM2 Nominal = 682A
IM2 Primary = 800A
IM2Secondary = 1.000A
Ie No Load = 30.0%

Kceiling = 3.00V/V
Xq = 0.80
f Nominal = 50.00Hz
Single Phase Machine = FALSE
[FIELD FLASHING]
Off Level = 0.0%
[SOFTSTART]
Starting Level = 20.0%
Hold Time = 2.0s
Ramp Time = 8.0s
Frequency Start Threshold = 0.0Hz
Line Charging Starting Level = 20.0%
Line Charging Hold Time = 20.0s
Line Charging Ramp Time = 80.0s
[V/Hz LIMITER]
fKnee = 48.0Hz
Slope = 90.0%
[IeMin LIMITER]
Minimum = 0.0%
Active = FALSE
[IeMax LIMITER]
Maximum = 160.0%
Maximum Hold Time = 10.0s
Delayed = 120.0%
Delayed Hold Time = 60.0s
Continuous = 105.0%
Active = TRUE
[PQ LIMITER]
Minimum Q (P @ 0%) = -40.0%
Minimum Q (P @ 25%) = -35.0%

Minimum Q (P @ 50%) = -30.0%

Minimum Q (P @ 75%) = -25.0%
Minimum Q (P @ 100%) = -20.0%
Voltage Dependency = TRUE
Active = TRUE
[UM LIMITER]
Minimum = 90.0%
Maximum = 110.0%
Minimum Active = TRUE
Maximum Active = TRUE
[BOOST]
Threshold = 40.0%
Hold Time = 3.0s
Hysteresis = 15.0%
Delayed OFF = 0.0s
Block Boosting in case of PT Alarm = FALSE
Boost on Grid only = FALSE
[FRT]
Power Threshold = 25.0%
Low Level = 40.0%
High Level = 55.0%
[AUTO SETPOINT]
Initial = 100.0%
Minimum = 95.0%
Maximum = 110.0%
Ramp Rate = 0.30%/s
Disable CB Check = FALSE
PF and VAR Initial SP Enabled = TRUE
Reset SP to Initial SP = FALSE
[PF SETPOINT]
Initial = 0.9500
Minimum = -0.8500

Maximum = 0.8500
Ramp Rate = 0.0050/s
[Var SETPOINT]
Initial = 0.0%
Minimum = -20.0%
Maximum = 100.0%
Ramp Rate = 1.00%/s
[MANUAL SETPOINT]
Initial = 0.0%
Minimum = 0.0%
Maximum = 150.0%
Ramp Rate = 1.67%/s
[OPEN LOOP SETPOINT]

Initial = 0.0%
Minimum = 0.0%
Maximum = 100.0%
Ramp Rate = 1.00%/s
[VDC]
Primary Net ID = 1
Secondary Net ID 1 = 2
Ramp Up Time = 10.0s
Segment Count = 0
Baud Rate = 59.9k
Error on 485 forces Auto = FALSE
Calc Ref from AVRs in VDC mode only = FALSE
[DIGITAL I/O 1]
Input = None
Polarity_IN = Normal
Output = None
Polarity_OUT = Normal

Direction = Out
[DIGITAL I/O 2]
Input = None
Output = None
Direction = Out
[DIGITAL I/O 3]
Input = None
Output = Limit_Active
Direction = Out
[DIGITAL I/O 4]
Input = None
Output = Diode_Trip
Direction = Out
[DIGITAL I/O 5]
Input = None
Output = Supervision_Alarm_2
Direction = Out
[DIGITAL I/O 6]
Input = None
Output = None
Direction = Out

[DIGITAL I/O 7]
Input = Reset_Alarm
Output = None
Direction = In
[DIGITAL I/O 8]
Input = None
Output = Switch_Over
Polarity_OUT = Inverted
Direction = Out
[DIGITAL INPUT 9]
Input = Excitation_ON
[DIGITAL INPUT 10]

Input = Parallel_With_Grid
[DIGITAL INPUT 11]

Input = Gen_CB_Closed
[DIGITAL INPUT 12]

Input = Manual_Enable
[DIGITAL INPUT 13 from +AI]

Input = Standby

[DIGITAL INPUT 14 from -AI]

Input = None

Input = Increase

Input = Decrease

Input = PF_Enable

Input = None
[ANALOG INPUT]
UM Aux Minimum = -10.0%
UM Aux Maximum = 10.0%
PSS Ext Maximum = 25.0%
[ANALOG INPUT 1]
Input = Din13&14
Uin 0% = 5.0V
Uin 100% = 8.0V
[ANALOG INPUT 2]
Input = Din15&16
Uin 0% = 5.0V
Uin 100% = 8.0V

[ANALOG INPUT 3]
Input = Din17&18
Uin 0% = 5.0V
Uin 100% = 8.0V
[ANALOG OUTPUT]
Output1 = None
Output2 = None
Uout1 0% = 0.0V
Uout1 100% = 10.0V
Uout2 0% = 0.0V
Uout2 100% = 10.0V
Ie 0% = 0.0%
Ie 100% = 300.0%
Fbias 0% = -3.0Hz
Fbias 100% = 3.0Hz
Slip 100% = 10.0Hz
Active Power 0% = -200.0%
Active Power 100% = 200.0%
Ue Field Voltage 100% = 450.0V
Upwr DC Link Voltage 100% = 450.0V
UM relative 100% = 199.9%
VAR relative 100% = 200.0%
[TUNE AUTO]
Proportional Gain (Vp) = 3.0
Derivation Time (Tb) = 0.20s
Integration Time (Ta) = 4.00s
Droop (Kq) = 0.0%
Derivation Gain (Kb) = 3
No Load Power Voltage = 0.0V
Kceil Freq. Dependency = FALSE
Max. PWM at Boost = FALSE
Uf @ Ie100% = 100%
Uf @ Ie200% = 200%
Uf @ Ie300% = 300%
Uf @ Ie400% = 400%
UfMax = 200%
UfLimGain = 0

[TUNE PF/Var/PQ LIMITER]

[TUNE MANUAL/Ie LIMITER]

[COMMUNICATION]
AVR ID = 1
Channel Identification = Main
TCP IP = 192.168.10.44
SubNet = 255.255.255.0
Gateway = 169.254.162.91
Control Password = 65535
[SYNCHRONIZATION]
UNetOffset = 0.0%
AnglOffset = 0.0deg
Min Slip = 0.00Hz
Max Slip = -0.40Hz
MaxDeltaU = 5.00%
Max Delta Angle = 10deg
Tot CB Close Time = 90ms
[DIODE MONITORING]
f Exc Nominal = 50Hz
Tconst Exc = 350ms
Active = FALSE
Alarm Level = 5.0%
Alarm Delay = 10.0s
Trip Level = 20.0%
Trip Delay = 0.3s
[IM Limiter]

IMlim_Active = FALSE
IMlim_K = 1.00
IMlim_Im_th = 100.0%
[TEMP INFLUENCE]
IMlim_T1 = 50.0°C
IMlim_Im_th2 = 75.0%
IMlim_T2 = 60.0°C
IMlim_T3 = 70.0°C
IMlim_T4 = 80.0°C
IElim_T1 = 50.0°C
IElim_Ie_th2 = 75.0%
IElim_T2 = 60.0°C
IElim_T3 = 70.0°C
IElim_T4 = 80.0°C
[MODBUS]
MB Slave ID = 247
MB_Protocol = 0
MB_Bitrate = 7
MB_ChrFrame = 0
MB_KeepAliveTime = 0s
MB_KeepAliveAction = 0
MB_Enable = FALSE
MB_Delay = 10ms
[DOUBLE CHANNEL]
Switchover Start Hold Time = 0.0s
CAN Enable = TRUE
Alarm 1 Enable = FALSE
Trip Enable = TRUE
Switchover block at Backup Alarm = FALSE
Switchover block at Backup Trip = TRUE
Alarm(DO) at Standby = TRUE
Trip(DO) at Standby = TRUE
Alarm(DO) Toggling = FALSE

Force Manual at Alarm 1 = FALSE

Force Excitation Off at Trip = FALSE
Disable ExcOff when GCB active = TRUE
UM Over Voltage Level = 150.0%
UM Over Voltage Hysteresis = 10.0%
UM Over Voltage Detection Time = 1.000s
UM Under Voltage Level = 50.0%
UM Under Voltage Hysteresis = 10.0%
UM Under Voltage Detection Time = 1.000s
Ie Over Current Level = 200.0%
Ie Over Current Hysteresis = 10.0%
Ie Over Current Detection Time = 0.500s
Reverse Power Level = -5.0%
Reverse Power Detection Time = 0.500s
Alarm 1 at loss of Remote Control = FALSE
Alarm 1 at Partial loss of UM = FALSE
Alarm 1 at loss of UM = FALSE
Alarm 1 at loss of UM phase 1 = FALSE
Alarm 1 at loss of Unet = FALSE
Alarm 1 at loss of IM = FALSE
Alarm 1 at loss of control = FALSE
Alarm 1 at loss of excitation = FALSE
Alarm 1 at Temperature 1 = FALSE
Alarm 1 at External Alarm = FALSE
Alarm 1 at 485 Error = FALSE
Alarm 1 at VDC Ring Error = FALSE
Alarm 1 at Internal Power Fail = FALSE
Alarm 1 at Digital Output Fail = FALSE
Alarm 1 at Monitor Alarm 1 = FALSE
Monitor Alarm 1 at FCB Alarm = FALSE
Monitor Alarm 1 at Diode Alarm = FALSE
Monitor Alarm 1 at Diode Trip = FALSE
Monitor Alarm 1 at UM Over Voltage = FALSE
Monitor Alarm 1 at UM Under Voltage = FALSE
Monitor Alarm 1 at Ie Over Current = FALSE
Monitor Alarm 1 at External Alarm = FALSE
Monitor Alarm 1 at Emergency Exc. OFF = FALSE

Monitor Alarm 1 at Reverse Power = FALSE

Monitor Alarm 1 at GCB Alarm = FALSE
Trip at loss of Remote Control = FALSE
Trip at Partial loss of UM = FALSE
Trip at loss of UM = FALSE
Trip at loss of UM phase 1 = FALSE
Trip at loss of Unet = FALSE
Trip at loss of IM = FALSE
Trip at loss of control = FALSE
Trip at loss of excitation = FALSE
Trip at temperature 1 = FALSE

Trip at Temperature 2 = FALSE

Trip at External Alarm = FALSE
Trip at 485 Error = FALSE
Trip at VDC Ring Error = FALSE
Trip at Internal Power Fail = FALSE
Trip at Digital Output Fail = FALSE
Trip at Monitor Alarm 1 = FALSE
[TIME]
SNTP IP = 169.254.162.91
SNTP Enabled = FALSE
Time Offset = 01:00
[DATA LOGGER]
Sample Rate = Off
Pre Trigger = 50.0%/bit
Trigger Event 1 = 0
Trigger Event 2 = 0
Trigger Event 3 = 0
Trigger Event 4 = 0
Trigger Event 5 = 0
Trigger Event 6 = 0
Trigger Event 7 = 0
Trigger Event 8 = 0
[MODBUS CHANNELS]
MB TCP Channel 0 = 0



CHANNEL-2 SETTINGS
;-----------------------------------------
; ABB Switzerland Ltd
; CMT 1000 v6.200
;
; UN1020 Parameter File
; Saved: 18.04.2021, 12:38
; AVR Serial Number: 00046200/5035
; Control SW Version: 6.318
; MCU SW Version: 6.318
;-----------------------------------------
[SYSTEM DATA]
Ie Nominal = 16.5A
Potential Transformer = Three_Phase
UM Nominal = 11.000kV
UM Primary = 11.000kV
UM Secondary = 100.0V
UNet Nominal = 11.00kV
UNet Primary = 66.00kV
UNet Secondary = 110.0V
IM2 Nominal = 682A
IM2 Primary = 800A
IM2Secondary = 1.000A
Ie No Load = 30.0%
Kceiling = 3.00V/V
Xq = 0.80
f Nominal = 50.00Hz
Single Phase Machine = FALSE
[FIELD FLASHING]
Off Level = 0.0%
[SOFTSTART]
Starting Level = 20.0%
Hold Time = 2.0s
Ramp Time = 8.0s
Frequency Start Threshold = 0.0Hz

Line Charging Starting Level = 20.0%

Line Charging Hold Time = 20.0s
Line Charging Ramp Time = 80.0s
[V/Hz LIMITER]
fKnee = 48.0Hz
Slope = 90.0%
[IeMin LIMITER]
Minimum = 0.0%
Active = FALSE
[IeMax LIMITER]
Maximum = 160.0%
Maximum Hold Time = 10.0s
Delayed = 120.0%
Delayed Hold Time = 60.0s
Continuous = 105.0%
Active = TRUE
[PQ LIMITER]
Minimum Q (P @ 0%) = -40.0%
Minimum Q (P @ 25%) = -35.0%
Minimum Q (P @ 50%) = -30.0%
Minimum Q (P @ 75%) = -25.0%
Minimum Q (P @ 100%) = -20.0%
Voltage Dependency = TRUE
Active = TRUE
[UM LIMITER]
Minimum = 90.0%
Maximum = 110.0%
Minimum Active = TRUE
Maximum Active = TRUE
[BOOST]

Threshold = 40.0%
Hold Time = 3.0s
Hysteresis = 15.0%
Delayed OFF = 0.0s
Block Boosting in case of PT Alarm = FALSE
Boost on Grid only = FALSE
[FRT]
Power Threshold = 25.0%
Low Level = 40.0%
High Level = 55.0%
[AUTO SETPOINT]
Initial = 100.0%
Minimum = 95.0%
Maximum = 110.0%
Ramp Rate = 0.30%/s
Disable CB Check = FALSE
PF and VAR Initial SP Enabled = TRUE
Reset SP to Initial SP = FALSE
[PF SETPOINT]
Initial = 0.9500
Minimum = -0.8500
Maximum = 0.8500
Ramp Rate = 0.0050/s
[Var SETPOINT]
Initial = 0.0%
Minimum = -20.0%
Maximum = 100.0%
Ramp Rate = 1.00%/s
[MANUAL SETPOINT]
Initial = 0.0%
Minimum = 0.0%
Maximum = 150.0%

Ramp Rate = 1.67%/s
[OPEN LOOP SETPOINT]

Initial = 0.0%
Minimum = 0.0%
Maximum = 100.0%
Ramp Rate = 1.00%/s
[VDC]
Primary Net ID = 1
Ramp Up Time = 10.0s
Segment Count = 0
Baud Rate = 59.9k
Error on 485 forces Auto = FALSE
Calc Ref from AVRs in VDC mode only = FALSE
[DIGITAL I/O 1]
Input = None
Output = None
Direction = Out
[DIGITAL I/O 2]
Input = None
Output = None
Direction = Out
[DIGITAL I/O 3]
Input = None
Output = Limit_Active

Direction = Out
[DIGITAL I/O 4]
Input = None
Output = Diode_Trip
Direction = Out
[DIGITAL I/O 5]
Input = None
Output = Supervision_Alarm_2
Direction = Out
[DIGITAL I/O 6]
Input = None
Output = None
Direction = Out
[DIGITAL I/O 7]
Input = Reset_Alarm
Output = None
Direction = In
[DIGITAL I/O 8]
Input = None
Output = Switch_Over
Polarity_OUT = Inverted
Direction = Out

[DIGITAL INPUT 9]
Input = Excitation_ON
[DIGITAL INPUT 10]

Input = Parallel_With_Grid
[DIGITAL INPUT 11]

Input = Gen_CB_Closed
[DIGITAL INPUT 12]

Input = Manual_Enable

Input = Standby

Input = None

Input = Increase

Input = Decrease


Input = PF_Enable

Input = None
[ANALOG INPUT]
UM Aux Minimum = -10.0%
UM Aux Maximum = 10.0%
PSS Ext Maximum = 25.0%
[ANALOG INPUT 1]
Input = Din13&14
Uin 0% = 5.0V
Uin 100% = 8.0V
[ANALOG INPUT 2]
Input = Din15&16
Uin 0% = 5.0V
Uin 100% = 8.0V
[ANALOG INPUT 3]
Input = Din17&18
Uin 0% = 5.0V
Uin 100% = 8.0V
[ANALOG OUTPUT]
Output1 = None
Output2 = None
Uout1 0% = 0.0V
Uout1 100% = 10.0V
Uout2 0% = 0.0V
Uout2 100% = 10.0V
Ie 0% = 0.0%

Ie 100% = 300.0%
Fbias 0% = -3.0Hz
Fbias 100% = 3.0Hz
Slip 100% = 10.0Hz
Active Power 0% = -200.0%
Active Power 100% = 200.0%
Ue Field Voltage 100% = 450.0V
Upwr DC Link Voltage 100% = 450.0V
UM relative 100% = 199.9%
VAR relative 100% = 200.0%
[TUNE AUTO]
Derivation Time (Tb) = 0.20s
Droop (Kq) = 0.0%
Derivation Gain (Kb) = 3
No Load Power Voltage = 0.0V
Kceil Freq. Dependency = FALSE
Max. PWM at Boost = FALSE
Uf @ Ie100% = 100%
Uf @ Ie200% = 200%
Uf @ Ie300% = 300%
Uf @ Ie400% = 400%
UfMax = 200%
UfLimGain = 0
[TUNE PF/Var/PQ LIMITER]

[TUNE MANUAL/Ie LIMITER]

[COMMUNICATION]
AVR ID = 1
Channel Identification = Main

TCP IP = 192.168.10.45
SubNet = 255.255.255.0
Gateway = 169.254.162.91
Control Password = 65535
[SYNCHRONIZATION]
UNetOffset = 0.0%
AnglOffset = 0.0deg
Min Slip = 0.00Hz
Max Slip = -0.40Hz
MaxDeltaU = 5.00%
Max Delta Angle = 10deg
Tot CB Close Time = 90ms
[DIODE MONITORING]
f Exc Nominal = 50Hz
Tconst Exc = 350ms
Active = FALSE
Alarm Level = 5.0%
Alarm Delay = 10.0s
Trip Level = 20.0%
Trip Delay = 0.3s
[IM Limiter]
IMlim_Active = FALSE
IMlim_K = 1.00
IMlim_Im_th = 100.0%
[TEMP INFLUENCE]
IMlim_T1 = 50.0°C
IMlim_T2 = 60.0°C
IMlim_T3 = 70.0°C
IMlim_T4 = 80.0°C
IElim_T1 = 50.0°C
IElim_T2 = 60.0°C

IElim_T3 = 70.0°C
IElim_T4 = 80.0°C
[MODBUS]
MB Slave ID = 247
MB_Protocol = 0
MB_Bitrate = 7
MB_ChrFrame = 0
MB_KeepAliveTime = 0s
MB_KeepAliveAction = 0
MB_Enable = FALSE
MB_Delay = 10ms
[DOUBLE CHANNEL]
Switchover Start Hold Time = 0.0s
CAN Enable = TRUE
Trip Enable = TRUE
Switchover block at Backup Alarm = FALSE
Switchover block at Backup Trip = TRUE
Alarm(DO) at Standby = TRUE
Trip(DO) at Standby = TRUE
Alarm(DO) Toggling = FALSE
Force Excitation Off at Trip = FALSE
Disable ExcOff when GCB active = TRUE
UM Over Voltage Level = 150.0%
UM Over Voltage Hysteresis = 10.0%
UM Over Voltage Detection Time = 1.000s
UM Under Voltage Level = 50.0%
UM Under Voltage Hysteresis = 10.0%
UM Under Voltage Detection Time = 1.000s
Ie Over Current Level = 200.0%
Ie Over Current Hysteresis = 10.0%
Ie Over Current Detection Time = 0.500s
Reverse Power Level = -5.0%
Reverse Power Detection Time = 0.500s




Trip at loss of Remote Control = FALSE
Trip at Partial loss of UM = FALSE
Trip at loss of UM = FALSE
Trip at loss of Unet = FALSE
Trip at loss of IM = FALSE
Trip at loss of control = FALSE
Trip at loss of excitation = FALSE
Trip at temperature 1 = FALSE
Trip at Temperature 2 = FALSE
Trip at External Alarm = FALSE
Trip at 485 Error = FALSE
Trip at VDC Ring Error = FALSE
Trip at Internal Power Fail = FALSE
Trip at Digital Output Fail = FALSE
[TIME]
SNTP IP = 169.254.162.91
SNTP Enabled = FALSE
Time Offset = 01:00

[DATA LOGGER]
Sample Rate = Off
Pre Trigger = 50.0%/bit
Trigger Event 1 = 0
Trigger Event 2 = 0
Trigger Event 3 = 0
Trigger Event 4 = 0
Trigger Event 5 = 0
Trigger Event 6 = 0
Trigger Event 7 = 0
Trigger Event 8 = 0
[MODBUS CHANNELS]

CHANNEL-1 AVR
Description Remarks
AVR Manual mode Voltage Buildup Found Ok
AVR Auto mode Voltage Buildup Found Ok

AVR voltage Manual mode Increase & Decrease Found Ok

AVR voltage Auto Mode Increase & Decrease Found Ok
AVR Manual mode Auto mode Transfer scheme Found Ok
AVR Auto mode Manual mode Transfer scheme
AVR in Auto mode channel1 to channel -2 Transfer scheme Found ok
Channel to Channel Transferring time no effect in Generator & not Found ok
operate in protection Scheme.
CHANNEL-2 AVR
Description Remarks
AVR Manual mode Voltage Buildup Found Ok
AVR Auto mode Voltage Buildup Found Ok
AVR voltage Manual mode Increase & Decrease Found Ok
AVR voltage Auto Mode Increase & Decrease Found Ok
AVR Manual mode Auto mode Transfer scheme Found Ok
AVR Auto mode Manual mode Transfer scheme
Channel to Channel Transferring time no effect in Generator & not Found ok
operate in protection Scheme.

Nelumbo Chilime Electrical Engineer Chilime Project Manager
Chilime Consultant


Sat Avr-1

Uploaded by

Copyright:

Available Formats

Sat Avr-1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sat Avr-1

Uploaded by

Copyright:

Available Formats

Site Acceptance Test (SAT)

SITE ACCEPTANCE TEST (SAT)

CUSTOMER : Chilime jalavidhyut company Limited

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Ref Document Reference Description

Digital Multi meter / Fluke 46311178WS

Health and Safety

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Minimum Q (P @ 50%) = -30.0%

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[OPEN LOOP SETPOINT]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[DIGITAL INPUT 10]

[DIGITAL INPUT 11]

[DIGITAL INPUT 12]

[DIGITAL INPUT 13 from +AI]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[DIGITAL INPUT 14 from -AI]

[DIGITAL INPUT 15 from +AI]

[DIGITAL INPUT 16 from -AI]

[DIGITAL INPUT 17 from +AI]

[DIGITAL INPUT 18 from -AI]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[TUNE PF/Var/PQ LIMITER]

[TUNE MANUAL/Ie LIMITER]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Force Manual at Alarm 1 = FALSE

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Monitor Alarm 1 at Reverse Power = FALSE

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Trip at Temperature 2 = FALSE

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Line Charging Starting Level = 20.0%

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Ramp Rate = 1.67%/s

[OPEN LOOP SETPOINT]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[DIGITAL INPUT 10]

[DIGITAL INPUT 11]

[DIGITAL INPUT 12]

[DIGITAL INPUT 13 from +AI]

[DIGITAL INPUT 14 from -AI]

[DIGITAL INPUT 15 from +AI]

[DIGITAL INPUT 16 from -AI]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[DIGITAL INPUT 17 from +AI]

[DIGITAL INPUT 18 from -AI]

Doc Type Site Acceptance Test report NICPL Doc No NICPL-137-01

[TUNE PF/Var/PQ LIMITER]